S-1315 Series
5.5 V INPUT, 200 mA,
OUTPUT CAPACITOR-LESS
VOLTAGE REGULATOR
www.ablic.com
Rev.1.4_00
© ABLIC Inc., 2011-2019
The S-1315 Series, developed by using the CMOS technology, is a positive voltage regulator IC of 200 mA output current
which has low dropout voltage, high-accuracy output voltage and low current consumption. The S-1315 Series enables high
density mounting due to output capacitor-less.
The current consumption is extremely low as 7 μA typ., and even without an output capacitor, it realizes high-speed
response.
It also has high-accuracy output voltage of ±1.0%.
Features
• Output voltage:
• Input voltage:
• Output voltage accuracy:
• Dropout voltage:
• Current consumption:
• Output current:
• Input and output capacitors:
• Ripple rejection:
• Built-in overcurrent protection circuit:
• Built-in ON / OFF circuit:
• Operation temperature range:
• Lead-free (Sn 100%), halogen-free
1.0 V to 4.2 V, selectable in 0.05 V step
1.4 V to 5.5 V
±1.0% (1.0 V to 1.45 V output product: ±15 mV)
224 mV typ. (3.0 V output product, IOUT = 200 mA)
During operation:
7 μA typ., 13 μA max.
During power-off:
0.1 μA typ., 1.0 μA max.
Possible to output 200 mA (VIN ≥ VOUT(S) + 1.0 V)*1
A ceramic capacitor of 0.1 μF or more can be used for the input capacitor.
Output capacitor is unnecessary, or a ceramic capacitor of 10 μF or less
can be used.
65 dB typ. (1.0 V output product, f = 1.0 kHz)
60 dB typ. (2.8 V output product, f = 1.0 kHz)
Limits overcurrent of output transistor.
Ensures long battery life.
Discharge shunt function "available" / "unavailable" is selectable.
Pull-down function "available" / "unavailable" is selectable.
Ta = −40°C to +85°C
*1. Attention should be paid to the power dissipation of the package when the output current is large.
Applications
• Constant-voltage power supply for battery-powered device
• Constant-voltage power supply for communication device
• Constant-voltage power supply for mobile phone
• Constant-voltage power supply for module
Packages
• SOT-23-5
• HSNT-6 (1212)
1
5.5 V INPUT, 200 mA, OUTPUT CAPACITOR-LESS VOLTAGE REGULATOR
Rev.1.4_00
S-1315 Series
Block Diagrams
1.
S-1315 Series A type
*1
VIN
VOUT
Overcurrent
protection circuit
ON / OFF
ON / OFF circuit
Function
ON / OFF logic
Discharge shunt
function
Constant current
source pull-down
Status
Active "H"
Function
ON / OFF logic
Discharge shunt
function
Constant current
source pull-down
Status
Active "H"
Available
Available
+
−
Reference
voltage circuit
*1
VSS
*1.
Parasitic diode
Figure 1
2.
S-1315 Series B type
*1
VIN
VOUT
Overcurrent
protection circuit
ON / OFF
ON / OFF circuit
+
−
Reference
voltage circuit
*1
VSS
*1.
Parasitic diode
Figure 2
2
Available
Unavailable
Rev.1.4_00
3.
5.5 V INPUT, 200 mA, OUTPUT CAPACITOR-LESS VOLTAGE REGULATOR
S-1315 Series
S-1315 Series C type
*1
VIN
VOUT
Overcurrent
protection circuit
ON / OFF
ON / OFF circuit
Function
ON / OFF logic
Discharge shunt
function
Constant current
source pull-down
Status
Active "H"
Function
ON / OFF logic
Discharge shunt
function
Constant current
source pull-down
Status
Active "H"
Unavailable
Available
+
−
Reference
voltage circuit
VSS
*1.
Parasitic diode
Figure 3
4.
S-1315 Series D type
*1
VIN
VOUT
Overcurrent
protection circuit
ON / OFF
ON / OFF circuit
Unavailable
Unavailable
+
−
Reference
voltage circuit
VSS
*1.
Parasitic diode
Figure 4
3
5.5 V INPUT, 200 mA, OUTPUT CAPACITOR-LESS VOLTAGE REGULATOR
Rev.1.4_00
S-1315 Series
Product Name Structure
Users can select the product type, output voltage, and package type for the S-1315 Series. Refer to "1. Product
name" regarding the contents of product name, "2. Function list of product types" regarding the product type,
"3. Packages" regarding the package drawings, "4. Product name lists" regarding details of the product name.
1.
Product name
S-1315
x
xx
-
xxxx
U
3
Environmental code
U:
Lead-free (Sn 100%), halogen-free
Package abbreviation and IC packing specifications
M5T1: SOT-23-5, Tape
A6T2: HSNT-6 (1212), Tape
*1
Output voltage*2
10 to 42
(e.g., when the output voltage is 1.0 V, it is expressed as 10.)
Product type*3
A to D
*1.
*2.
*3.
2.
Refer to the tape drawing.
If you request the product which has 0.05 V step, contact our sales office.
Refer to "2. Function list of product types".
Function list of product types
Table 1
Product Type
A
B
C
D
3.
ON / OFF Logic
Active "H"
Active "H"
Active "H"
Active "H"
Constant Current Source Pull-down
Available
Unavailable
Available
Unavailable
Packages
Table 2
Package Name
SOT-23-5
HSNT-6 (1212)
4
Discharge Shunt Function
Available
Available
Unavailable
Unavailable
Dimension
MP005-A-P-SD
PM006-A-P-SD
Package Drawing Codes
Tape
MP005-A-C-SD
PM006-A-C-SD
Reel
MP005-A-R-SD
PM006-A-R-SD
Land
−
PM006-A-L-SD
Rev.1.4_00
4.
5.5 V INPUT, 200 mA, OUTPUT CAPACITOR-LESS VOLTAGE REGULATOR
S-1315 Series
Product name lists
4. 1
S-1315 Series A type
ON / OFF logic:
Discharge shunt function:
Active "H"
Available
Constant current source pull-down: Available
Table 3
Output Voltage
1.0 V ± 15 mV
1.1 V ± 15 mV
1.2 V ± 15 mV
1.3 V ± 15 mV
1.4 V ± 15 mV
1.5 V ± 1.0%
1.6 V ± 1.0%
1.7 V ± 1.0%
1.8 V ± 1.0%
1.85 V ± 1.0%
1.9 V ± 1.0%
2.0 V ± 1.0%
2.1 V ± 1.0%
2.2 V ± 1.0%
2.3 V ± 1.0%
2.4 V ± 1.0%
2.5 V ± 1.0%
2.6 V ± 1.0%
2.7 V ± 1.0%
2.8 V ± 1.0%
2.85 V ± 1.0%
2.9 V ± 1.0%
3.0 V ± 1.0%
3.1 V ± 1.0%
3.2 V ± 1.0%
3.3 V ± 1.0%
3.4 V ± 1.0%
3.5 V ± 1.0%
3.6V ± 1.0%
3.7V ± 1.0%
3.8V ± 1.0%
3.9V ± 1.0%
4.0 V ± 1.0%
4.1 V ± 1.0%
4.2 V ± 1.0%
Remark
SOT-23-5
S-1315A10-M5T1U3
S-1315A11-M5T1U3
S-1315A12-M5T1U3
S-1315A13-M5T1U3
S-1315A14-M5T1U3
S-1315A15-M5T1U3
S-1315A16-M5T1U3
S-1315A17-M5T1U3
S-1315A18-M5T1U3
S-1315A1J-M5T1U3
S-1315A19-M5T1U3
S-1315A20-M5T1U3
S-1315A21-M5T1U3
S-1315A22-M5T1U3
S-1315A23-M5T1U3
S-1315A24-M5T1U3
S-1315A25-M5T1U3
S-1315A26-M5T1U3
S-1315A27-M5T1U3
S-1315A28-M5T1U3
S-1315A2J-M5T1U3
S-1315A29-M5T1U3
S-1315A30-M5T1U3
S-1315A31-M5T1U3
S-1315A32-M5T1U3
S-1315A33-M5T1U3
S-1315A34-M5T1U3
S-1315A35-M5T1U3
S-1315A36-M5T1U3
S-1315A37-M5T1U3
S-1315A38-M5T1U3
S-1315A39-M5T1U3
S-1315A40-M5T1U3
S-1315A41-M5T1U3
S-1315A42-M5T1U3
HSNT-6 (1212)
S-1315A10-A6T2U3
S-1315A11-A6T2U3
S-1315A12-A6T2U3
S-1315A13-A6T2U3
S-1315A14-A6T2U3
S-1315A15-A6T2U3
S-1315A16-A6T2U3
S-1315A17-A6T2U3
S-1315A18-A6T2U3
S-1315A1J-A6T2U3
S-1315A19-A6T2U3
S-1315A20-A6T2U3
S-1315A21-A6T2U3
S-1315A22-A6T2U3
S-1315A23-A6T2U3
S-1315A24-A6T2U3
S-1315A25-A6T2U3
S-1315A26-A6T2U3
S-1315A27-A6T2U3
S-1315A28-A6T2U3
S-1315A2J-A6T2U3
S-1315A29-A6T2U3
S-1315A30-A6T2U3
S-1315A31-A6T2U3
S-1315A32-A6T2U3
S-1315A33-A6T2U3
S-1315A34-A6T2U3
S-1315A35-A6T2U3
S-1315A36-A6T2U3
S-1315A37-A6T2U3
S-1315A38-A6T2U3
S-1315A39-A6T2U3
S-1315A40-A6T2U3
S-1315A41-A6T2U3
S-1315A42-A6T2U3
Please contact our sales office for products other than the above.
5
5.5 V INPUT, 200 mA, OUTPUT CAPACITOR-LESS VOLTAGE REGULATOR
Rev.1.4_00
S-1315 Series
4. 2
S-1315 Series B type
ON / OFF logic:
Discharge shunt function:
Active "H"
Available
Constant current source pull-down: Unavailable
Table 4
Output Voltage
1.0 V ± 15 mV
1.1 V ± 15 mV
1.2 V ± 15 mV
1.3 V ± 15 mV
1.4 V ± 15 mV
1.5 V ± 1.0%
1.6 V ± 1.0%
1.7 V ± 1.0%
1.8 V ± 1.0%
1.85 V ± 1.0%
1.9 V ± 1.0%
2.0 V ± 1.0%
2.1 V ± 1.0%
2.2 V ± 1.0%
2.3 V ± 1.0%
2.4 V ± 1.0%
2.5 V ± 1.0%
2.6 V ± 1.0%
2.7 V ± 1.0%
2.8 V ± 1.0%
2.85 V ± 1.0%
2.9 V ± 1.0%
3.0 V ± 1.0%
3.1 V ± 1.0%
3.2 V ± 1.0%
3.3 V ± 1.0%
3.4 V ± 1.0%
3.5 V ± 1.0%
3.6 V ± 1.0%
3.7 V ± 1.0%
3.8 V ± 1.0%
3.9 V ± 1.0%
4.0 V ± 1.0%
4.1 V ± 1.0%
4.2 V ± 1.0%
Remark
6
SOT-23-5
S-1315B10-M5T1U3
S-1315B11-M5T1U3
S-1315B12-M5T1U3
S-1315B13-M5T1U3
S-1315B14-M5T1U3
S-1315B15-M5T1U3
S-1315B16-M5T1U3
S-1315B17-M5T1U3
S-1315B18-M5T1U3
S-1315B1J-M5T1U3
S-1315B19-M5T1U3
S-1315B20-M5T1U3
S-1315B21-M5T1U3
S-1315B22-M5T1U3
S-1315B23-M5T1U3
S-1315B24-M5T1U3
S-1315B25-M5T1U3
S-1315B26-M5T1U3
S-1315B27-M5T1U3
S-1315B28-M5T1U3
S-1315B2J-M5T1U3
S-1315B29-M5T1U3
S-1315B30-M5T1U3
S-1315B31-M5T1U3
S-1315B32-M5T1U3
S-1315B33-M5T1U3
S-1315B34-M5T1U3
S-1315B35-M5T1U3
S-1315B36-M5T1U3
S-1315B37-M5T1U3
S-1315B38-M5T1U3
S-1315B39-M5T1U3
S-1315B40-M5T1U3
S-1315B41-M5T1U3
S-1315B42-M5T1U3
HSNT-6 (1212)
S-1315B10-A6T2U3
S-1315B11-A6T2U3
S-1315B12-A6T2U3
S-1315B13-A6T2U3
S-1315B14-A6T2U3
S-1315B15-A6T2U3
S-1315B16-A6T2U3
S-1315B17-A6T2U3
S-1315B18-A6T2U3
S-1315B1J-A6T2U3
S-1315B19-A6T2U3
S-1315B20-A6T2U3
S-1315B21-A6T2U3
S-1315B22-A6T2U3
S-1315B23-A6T2U3
S-1315B24-A6T2U3
S-1315B25-A6T2U3
S-1315B26-A6T2U3
S-1315B27-A6T2U3
S-1315B28-A6T2U3
S-1315B2J-A6T2U3
S-1315B29-A6T2U3
S-1315B30-A6T2U3
S-1315B31-A6T2U3
S-1315B32-A6T2U3
S-1315B33-A6T2U3
S-1315B34-A6T2U3
S-1315B35-A6T2U3
S-1315B36-A6T2U3
S-1315B37-A6T2U3
S-1315B38-A6T2U3
S-1315B39-A6T2U3
S-1315B40-A6T2U3
S-1315B41-A6T2U3
S-1315B42-A6T2U3
Please contact our sales office for products other than the above.
Rev.1.4_00
4. 3
5.5 V INPUT, 200 mA, OUTPUT CAPACITOR-LESS VOLTAGE REGULATOR
S-1315 Series
S-1315 Series C type
ON / OFF logic:
Discharge shunt function:
Active "H"
Unavailable
Constant current source pull-down: Available
Table 5
SOT-23-5
HSNT-6 (1212)
Output Voltage
1.0 V ± 15 mV
S-1315C10-M5T1U3
S-1315C10-A6T2U3
1.1 V ± 15 mV
S-1315C11-M5T1U3
S-1315C11-A6T2U3
1.2 V ± 15 mV
S-1315C12-M5T1U3
S-1315C12-A6T2U3
1.3 V ± 15 mV
S-1315C13-M5T1U3
S-1315C13-A6T2U3
1.4 V ± 15 mV
S-1315C14-M5T1U3
S-1315C14-A6T2U3
1.5 V ± 1.0%
S-1315C15-M5T1U3
S-1315C15-A6T2U3
1.6 V ± 1.0%
S-1315C16-M5T1U3
S-1315C16-A6T2U3
1.7 V ± 1.0%
S-1315C17-M5T1U3
S-1315C17-A6T2U3
1.8 V ± 1.0%
S-1315C18-M5T1U3
S-1315C18-A6T2U3
1.85 V ± 1.0%
S-1315C1J-M5T1U3
S-1315C1J-A6T2U3
1.9 V ± 1.0%
S-1315C19-M5T1U3
S-1315C19-A6T2U3
2.0 V ± 1.0%
S-1315C20-M5T1U3
S-1315C20-A6T2U3
2.1 V ± 1.0%
S-1315C21-M5T1U3
S-1315C21-A6T2U3
2.2 V ± 1.0%
S-1315C22-M5T1U3
S-1315C22-A6T2U3
2.3 V ± 1.0%
S-1315C23-M5T1U3
S-1315C23-A6T2U3
2.4 V ± 1.0%
S-1315C24-M5T1U3
S-1315C24-A6T2U3
2.5 V ± 1.0%
S-1315C25-M5T1U3
S-1315C25-A6T2U3
2.6 V ± 1.0%
S-1315C26-M5T1U3
S-1315C26-A6T2U3
2.7 V ± 1.0%
S-1315C27-M5T1U3
S-1315C27-A6T2U3
2.8 V ± 1.0%
S-1315C28-M5T1U3
S-1315C28-A6T2U3
2.85 V ± 1.0%
S-1315C2J-M5T1U3
S-1315C2J-A6T2U3
2.9 V ± 1.0%
S-1315C29-M5T1U3
S-1315C29-A6T2U3
3.0 V ± 1.0%
S-1315C30-M5T1U3
S-1315C30-A6T2U3
3.1 V ± 1.0%
S-1315C31-M5T1U3
S-1315C31-A6T2U3
3.2 V ± 1.0%
S-1315C32-M5T1U3
S-1315C32-A6T2U3
3.3 V ± 1.0%
S-1315C33-M5T1U3
S-1315C33-A6T2U3
3.4 V ± 1.0%
S-1315C34-M5T1U3
S-1315C34-A6T2U3
3.5 V ± 1.0%
S-1315C35-M5T1U3
S-1315C35-A6T2U3
S-1315C36-M5T1U3
S-1315C36-A6T2U3
3.6 V ± 1.0%
S-1315C37-M5T1U3
S-1315C37-A6T2U3
3.7 V ± 1.0%
S-1315C38-M5T1U3
S-1315C38-A6T2U3
3.8 V ± 1.0%
S-1315C39-M5T1U3
S-1315C39-A6T2U3
3.9 V ± 1.0%
S-1315C40-M5T1U3
S-1315C40-A6T2U3
4.0 V ± 1.0%
S-1315C41-M5T1U3
S-1315C41-A6T2U3
4.1 V ± 1.0%
S-1315C42-M5T1U3
S-1315C42-A6T2U3
4.2 V ± 1.0%
Remark Please contact our sales office for products other than the above.
7
5.5 V INPUT, 200 mA, OUTPUT CAPACITOR-LESS VOLTAGE REGULATOR
Rev.1.4_00
S-1315 Series
4. 4
S-1315 Series D type
ON / OFF logic:
Discharge shunt function:
Active "H"
Unavailable
Constant current source pull-down: Unavailable
Table 6
Output Voltage
1.0 V ± 15 mV
1.1 V ± 15 mV
1.2 V ± 15 mV
1.3 V ± 15 mV
1.4 V ± 15 mV
1.5 V ± 1.0%
1.6 V ± 1.0%
1.7 V ± 1.0%
1.8 V ± 1.0%
1.85 V ± 1.0%
1.9 V ± 1.0%
2.0 V ± 1.0%
2.1 V ± 1.0%
2.2 V ± 1.0%
2.3 V ± 1.0%
2.4 V ± 1.0%
2.5 V ± 1.0%
2.6 V ± 1.0%
2.7 V ± 1.0%
2.8 V ± 1.0%
2.85 V ± 1.0%
2.9 V ± 1.0%
3.0 V ± 1.0%
3.1 V ± 1.0%
3.2 V ± 1.0%
3.3 V ± 1.0%
3.4 V ± 1.0%
3.5 V ± 1.0%
3.6 V ± 1.0%
3.7 V ± 1.0%
3.8 V ± 1.0%
3.9 V ± 1.0%
4.0 V ± 1.0%
4.1 V ± 1.0%
4.2 V ± 1.0%
Remark
8
SOT-23-5
S-1315D10-M5T1U3
S-1315D11-M5T1U3
S-1315D12-M5T1U3
S-1315D13-M5T1U3
S-1315D14-M5T1U3
S-1315D15-M5T1U3
S-1315D16-M5T1U3
S-1315D17-M5T1U3
S-1315D18-M5T1U3
S-1315D1J-M5T1U3
S-1315D19-M5T1U3
S-1315D20-M5T1U3
S-1315D21-M5T1U3
S-1315D22-M5T1U3
S-1315D23-M5T1U3
S-1315D24-M5T1U3
S-1315D25-M5T1U3
S-1315D26-M5T1U3
S-1315D27-M5T1U3
S-1315D28-M5T1U3
S-1315D2J-M5T1U3
S-1315D29-M5T1U3
S-1315D30-M5T1U3
S-1315D31-M5T1U3
S-1315D32-M5T1U3
S-1315D33-M5T1U3
S-1315D34-M5T1U3
S-1315D35-M5T1U3
S-1315D36-M5T1U3
S-1315D37-M5T1U3
S-1315D38-M5T1U3
S-1315D39-M5T1U3
S-1315D40-M5T1U3
S-1315D41-M5T1U3
S-1315D42-M5T1U3
HSNT-6 (1212)
S-1315D10-A6T2U3
S-1315D11-A6T2U3
S-1315D12-A6T2U3
S-1315D13-A6T2U3
S-1315D14-A6T2U3
S-1315D15-A6T2U3
S-1315D16-A6T2U3
S-1315D17-A6T2U3
S-1315D18-A6T2U3
S-1315D1J-A6T2U3
S-1315D19-A6T2U3
S-1315D20-A6T2U3
S-1315D21-A6T2U3
S-1315D22-A6T2U3
S-1315D23-A6T2U3
S-1315D24-A6T2U3
S-1315D25-A6T2U3
S-1315D26-A6T2U3
S-1315D27-A6T2U3
S-1315D28-A6T2U3
S-1315D2J-A6T2U3
S-1315D29-A6T2U3
S-1315D30-A6T2U3
S-1315D31-A6T2U3
S-1315D32-A6T2U3
S-1315D33-A6T2U3
S-1315D34-A6T2U3
S-1315D35-A6T2U3
S-1315D36-A6T2U3
S-1315D37-A6T2U3
S-1315D38-A6T2U3
S-1315D39-A6T2U3
S-1315D40-A6T2U3
S-1315D41-A6T2U3
S-1315D42-A6T2U3
Please contact our sales office for products other than the above.
Rev.1.4_00
5.5 V INPUT, 200 mA, OUTPUT CAPACITOR-LESS VOLTAGE REGULATOR
S-1315 Series
Pin Configurations
1.
SOT-23-5
Table 7
Top view
5
4
1 2 3
Pin No.
1
2
3
4
5
Symbol
VIN
VSS
ON / OFF
NC*1
VOUT
Description
Input voltage pin
GND pin
ON / OFF pin
No connection
Output voltage pin
Figure 5
*1.
2.
The NC pin is electrically open.
The NC pin can be connected to the VIN pin or the VSS pin.
HSNT-6 (1212)
Table 8
Top view
1
2
3
6
5
4
Bottom view
6
5
4
1
2
3
Pin No.
1
2
3
4
5
6
Symbol
VOUT
VSS
NC*2
ON / OFF
NC*2
VIN
Description
Output voltage pin
GND pin
No connection
ON / OFF pin
No connection
Input voltage pin
*1
Figure 6
*1.
Connect the heat sink of backside at shadowed area to the board, and set electric potential GND.
However, do not use it as the function of electrode.
*2. The NC pin is electrically open.
The NC pin can be connected to the VIN pin or the VSS pin.
9
5.5 V INPUT, 200 mA, OUTPUT CAPACITOR-LESS VOLTAGE REGULATOR
Rev.1.4_00
S-1315 Series
Absolute Maximum Ratings
Table 9
Item
Symbol
VIN
VON / OFF
VOUT
IOUT
Input voltage
Output voltage
Output current
SOT-23-5
PD
HSNT-6 (1212)
Operation ambient temperature
Topr
Storage temperature
Tstg
*1. When mounted on board
[Mounted board]
(1) Board size:
114.3 mm × 76.2 mm × t1.6 mm
(2) Name:
JEDEC STANDARD51-7
Power dissipation
Caution
(Ta = +25°C unless otherwise specified)
Absolute Maximum Rating
Unit
VSS − 0.3 to VSS + 6.0
VSS − 0.3 to VIN + 0.3
VSS − 0.3 to VIN + 0.3
260
600*1
480*1
−40 to +85
−40 to +125
The absolute maximum ratings are rated values exceeding which the product could suffer physical
damage. These values must therefore not be exceeded under any conditions.
Power Dissipation (PD) [mW]
1200
1000
800
Figure 7
HSNT-6 (1212)
SOT-23-5
600
400
200
0
10
V
V
V
mA
mW
mW
°C
°C
0
150
100
50
Ambient Temperature (Ta) [°C]
Power Dissipation of Package (When Mounted on Board)
Rev.1.4_00
5.5 V INPUT, 200 mA, OUTPUT CAPACITOR-LESS VOLTAGE REGULATOR
S-1315 Series
Power Dissipation of HSNT-6 (1212) (Reference)
Power dissipation of package differs depending on the mounting conditions.
Consider the power dissipation characteristics under the following conditions as reference.
[Mounted board]
(1) Board size:
(2) Board material:
(3) Wiring ratio:
(4) Test conditions:
(5) Land pattern:
40 mm × 40 mm × t0.8 mm
Glass epoxy resin (four layers)
50%
When mounted on board (wind speed: 0 m/s)
Refer to the recommended land pattern (drawing code: PM006-A-L-SD)
Power Dissipation (PD) [mW]
1200
1000
800
600
400
200
0
Figure 8
0
150
100
50
Ambient Temperature (Ta) [°C]
Power Dissipation of Package (When Mounted on Board)
Table 10
Condition
HSNT-6 (1212)
(When mounted on board)
Power Dissipation (Reference)
Thermal Resistance Value (θj−a)
1000 mW
100°C/W
11
5.5 V INPUT, 200 mA, OUTPUT CAPACITOR-LESS VOLTAGE REGULATOR
Rev.1.4_00
S-1315 Series
Electrical Characteristics
Table 11
Item
Output voltage*1
Output current*2
Dropout voltage*3
Line regulation
Load regulation
Output voltage
temperature coefficient*4
Current consumption
during operation
Current consumption
during power-off
Input voltage
Symbol
VOUT(E)
IOUT
Vdrop
ΔVOUT1
12
VIN ≥ VOUT(S) + 1.0 V
IOUT = 200 mA
1.0 V ≤ VOUT(S) < 1.1 V
1.1 V ≤ VOUT(S) < 1.2 V
1.2 V ≤ VOUT(S) < 1.5 V
1.5 V ≤ VOUT(S) < 2.0 V
2.0 V ≤ VOUT(S) < 2.6 V
2.6 V ≤ VOUT(S) ≤ 4.2 V
0.2
%/V
1
VIN = VOUT(S) + 1.0 V, 1 mA ≤ IOUT ≤ 200 mA
−
25
50
mV
1
ΔTa • VOUT
VIN = VOUT(S) + 1.0 V, IOUT = 30 mA
−40°C ≤ Ta ≤ +85°C
−
±100
−
ppm/°C
1
ISS1
VIN = VOUT(S) + 1.0 V, ON / OFF pin = ON, no load
−
7.0
13
μA
2
ISS2
VIN = VOUT(S) + 1.0 V, ON / OFF pin = OFF, no load
−
0.1
1.0
μA
2
VIN
−
VIN = VOUT(S) + 1.0 V, RL = 1.0 kΩ
determined by VOUT output level
VIN = VOUT(S) + 1.0 V, RL = 1.0 kΩ
determined by VOUT output level
A / C type
(with constant current source
pull-down)
VIN = 5.5 V,
VON / OFF = 5.5 V
B / D type
(without constant current
source pull-down)
1.4
−
5.5
V
−
1.0
−
−
V
4
−
−
0.30
V
4
−
0.1
−
μA
4
−0.1
−
0.1
μA
4
−0.1
−
0.1
μA
4
VIN = VOUT(S) + 1.0 V, 1.0 V ≤ VOUT(S) ≤ 1.2 V
f = 1.0 kHz,
1.2 V < VOUT(S) ≤ 2.8 V
ΔVrip = 0.2 Vrms,
IOUT = 30 mA
2.8 V < VOUT(S) ≤ 4.2 V
−
65
−
dB
5
−
60
−
dB
5
−
55
−
dB
5
VIN = VOUT(S) + 1.0 V, ON / OFF pin = ON, VOUT = 0 V
VIN = 5.5 V,
A / B type
VOUT = 0.1 V
(with discharge shunt function)
−
50
−
mA
3
−
30
−
Ω
3
ΔVOUT2
ΔVOUT
VSL
Short-circuit current
Discharge shunt resistance
during power-off
1.5 V ≤ VOUT(S) ≤ 4.2 V
0.05
ON / OFF pin input voltage "L"
Ripple rejection
1.0 V ≤ VOUT(S) < 1.5 V
−
VSH
ON / OFF pin input current "L"
VIN = VOUT(S) + 1.0 V,
IOUT = 30 mA
VOUT(S) + 0.5 V ≤ VIN ≤ 5.5 V, IOUT = 30 mA
ΔVIN • VOUT
ON / OFF pin input voltage "H"
ON / OFF pin input current "H"
Condition
(Ta = +25°C unless otherwise specified)
Test
Min.
Typ.
Max.
Unit
Circuit
VOUT(S)
VOUT(S)
VOUT(S)
V
1
− 0.015
+ 0.015
VOUT(S)
VOUT(S)
VOUT(S)
V
1
× 0.99
× 1.01
200*5
−
−
mA
3
0.629
0.844
V
1
−
0.554
0.744
V
1
−
0.485
0.665
V
1
−
0.371
0.486
V
1
−
0.272
0.344
V
1
−
0.224
0.280
V
1
−
ISH
ISL
RR
Ishort
RLOW
VIN = 5.5 V, VON / OFF = 0 V
Rev.1.4_00
5.5 V INPUT, 200 mA, OUTPUT CAPACITOR-LESS VOLTAGE REGULATOR
S-1315 Series
*1. VOUT(S): Set output voltage
VOUT(E): Actual output voltage
Output voltage when fixing IOUT (= 30 mA) and inputting VOUT(S) + 1.0 V
*2. The output current at which the output voltage becomes 95% of VOUT(E) after gradually increasing the output current.
*3. Vdrop = VIN1 − (VOUT3 × 0.98)
VOUT3 is the output voltage when VIN = VOUT(S) + 1.0 V and IOUT = 200 mA.
VIN1 is the input voltage at which the output voltage becomes 98% of VOUT3 after gradually decreasing the input
voltage.
*4. A change in the temperature of the output voltage [mV/°C] is calculated using the following equation.
ΔVOUT
ΔVOUT
[mV/°C]*1 = VOUT(S) [V]*2 × ΔTa•VOUT [ppm/°C]*3 ÷ 1000
ΔTa
*1. Change in temperature of output voltage
*2. Set output voltage
*3. Output voltage temperature coefficient
*5. The output current can be at least this value.
Due to restrictions on the package power dissipation, this value may not be satisfied. Attention should be paid to the
power dissipation of the package when the output current is large.
This specification is guaranteed by design.
13
5.5 V INPUT, 200 mA, OUTPUT CAPACITOR-LESS VOLTAGE REGULATOR
Rev.1.4_00
S-1315 Series
Test Circuits
+
VOUT
VIN
ON / OFF
VSS
V
A
+
Set to ON
Figure 9
+
A
Test Circuit 1
VOUT
VIN
ON / OFF
VSS
Set to VIN or GND
Figure 10
Test Circuit 2
VOUT
VIN
ON / OFF
A
V
+
VSS
Set to VIN or GND
Figure 11
Test Circuit 3
VOUT
VIN
+
A
ON / OFF
V
+
VSS
Figure 12
Test Circuit 4
VOUT
VIN
ON / OFF
V
VSS
Set to ON
Figure 13
14
RL
Test Circuit 5
+
RL
Rev.1.4_00
5.5 V INPUT, 200 mA, OUTPUT CAPACITOR-LESS VOLTAGE REGULATOR
S-1315 Series
Standard Circuit
Input
Output
VOUT
VIN
CIN*1
ON / OFF
VSS
Single GND
CL
*2
GND
*1. CIN is a capacitor for stabilizing the input.
*2. An output capacitor (CL) is unnecessary.
However, if it is used, select an output capacitor which is 10 μF or less.
Figure 14
Caution
The above connection diagram and constants will not guarantee successful operation. Perform
thorough evaluation using the actual application to set the constants.
Condition of Application
Input capacitor (CIN):
Output capacitor (CL):
0.1 μF or more
Unnecessary, or an output capacitor which is 10 μF or less.
Caution Generally a series regulator may cause oscillation, depending on the selection of external parts.
Confirm that no oscillation occurs in the application for which the above capacitors are used.
Selection of Input and Output Capacitors (CIN, CL)
The S-1315 Series does not require an output capacitor between the VOUT pin and the VSS pin for phase
compensation. Operation is stabilized even without an output capacitor over the entire temperature range. If the
capacitor is used, the operation is stabilized with a ceramic capacitor which is CL ≤ 10 μF in the same way. Moreover,
when using an OS capacitor, a tantalum capacitor, or an aluminum electrolytic capacitor, the capacitance must be 10 μF
or less.
The value of the output overshoot or undershoot transient response varies depending on the value of the output
capacitor. The required capacitance of the input capacitor differs depending on the application.
The recommended capacitance for an application is CIN ≥ 0.1 μF; however, when selecting the output capacitor, perform
sufficient evaluation, including evaluation of temperature characteristics, on the actual device.
15
5.5 V INPUT, 200 mA, OUTPUT CAPACITOR-LESS VOLTAGE REGULATOR
Rev.1.4_00
S-1315 Series
Explanation of Terms
1.
Low dropout voltage regulator
This voltage regulator has the low dropout voltage due to its built-in low on-resistance transistor.
2.
Output voltage (VOUT)
The accuracy of the output voltage is ensured at ±1.0% or ±15 mV*1 under the specified conditions of fixed input
voltage*2, fixed output current, and fixed temperature.
*1.
*2.
When VOUT < 1.5 V: ±15 mV, when VOUT ≥ 1.5 V: ±1.0%
Differs depending on the product.
Caution
3.
If the above conditions change, the output voltage value may vary and exceed the accuracy range
of the output voltage. Refer to " Electrical Characteristics" and " Characteristics (Typical
Data)" for details.
ΔVOUT1
Line regulation
ΔVIN•VOUT
Indicates the dependency of the output voltage on the input voltage. That is, the values show how much the output
voltage changes due to a change in the input voltage with the output current remaining unchanged.
4.
Load regulation (ΔVOUT2)
Indicates the dependency of the output voltage on the output current. That is, the values show how much the output
voltage changes due to a change in the output current with the input voltage remaining unchanged.
5.
Dropout voltage (Vdrop)
Indicates the difference between input voltage (VIN1) and the output voltage when; decreasing input voltage (VIN)
gradually until the output voltage has dropped out to the value of 98% of output voltage (VOUT3), which is at
VIN = VOUT(S) + 1.0 V.
Vdrop = VIN1 − (VOUT3 × 0.98)
16
Rev.1.4_00
6.
5.5 V INPUT, 200 mA, OUTPUT CAPACITOR-LESS VOLTAGE REGULATOR
S-1315 Series
ΔVOUT
Output voltage temperature coefficient
ΔTa•VOUT
The shaded area in Figure 15 is the range where VOUT varies in the operation temperature range when the output
voltage temperature coefficient is ±100 ppm/°C.
Example of the S-1315A10 typ. product
VOUT
[V]
+0.10 mV/°C
*1
VOUT(E)
−0.10 mV/°C
−40
*1.
+25
+85
Ta [°C]
VOUT(E) is the value of the output voltage measured at Ta = +25°C.
Figure 15
A change in the temperature of the output voltage [mV/°C] is calculated using the following equation.
ΔVOUT
ΔVOUT
[mV/°C]*1 = VOUT(S) [V]*2 × ΔTa•VOUT [ppm/°C]*3 ÷ 1000
ΔTa
*1. Change in temperature of output voltage
*2. Set output voltage
*3. Output voltage temperature coefficient
17
5.5 V INPUT, 200 mA, OUTPUT CAPACITOR-LESS VOLTAGE REGULATOR
Rev.1.4_00
S-1315 Series
Operation
1.
Basic operation
Figure 16 shows the block diagram of the S-1315 Series.
The error amplifier compares the reference voltage (Vref) with feedback voltage (Vfb), which is the output voltage
resistance-divided by feedback resistors (Rs and Rf). It supplies the gate voltage necessary to maintain the constant
output voltage which is not influenced by the input voltage and temperature change, to the output transistor.
VIN
*1
Current
supply
Error
amplifier
Vref
VOUT
−
Rf
+
Vfb
Reference voltage
circuit
Rs
VSS
*1.
Parasitic diode
Figure 16
2.
Output transistor
In the S-1315 Series, a low on-resistance P-channel MOS FET is used as the output transistor.
Be sure that VOUT does not exceed VIN + 0.3 V to prevent the voltage regulator from being damaged due to reverse
current flowing from the VOUT pin through a parasitic diode to the VIN pin, when the potential of VOUT became higher
than VIN.
18
Rev.1.4_00
3.
5.5 V INPUT, 200 mA, OUTPUT CAPACITOR-LESS VOLTAGE REGULATOR
S-1315 Series
ON / OFF pin
This pin starts and stops the regulator.
When the ON / OFF pin is set to OFF level, the entire internal circuit stops operating, and the built-in
P-channel MOS FET output transistor between the VIN pin and the VOUT pin is turned off, reducing current
consumption significantly.
Note that the current consumption increases when a voltage of 0.25 V to 1.0 V is applied to the ON / OFF pin.
The ON / OFF pin is configured as shown in Figure 17 and Figure 18.
3. 1 S-1315 Series A / C type
The ON / OFF pin is internally pulled down to the VSS pin in the floating status, so the VOUT pin is set to the VSS
level. For the ON / OFF pin current, refer to the A / C type of ON / OFF pin input current "H" in " Electrical
Characteristics".
3. 2 S-1315 Series B / D type
The ON / OFF pin is internally not pulled up or pulled down, so do not use this pin in the floating status. When not
using the ON / OFF pin, connect the pin to the VIN pin.
Product Type
A/B/C/D
A/B/C/D
ON / OFF Pin
"H": ON
"L": OFF
Table 12
Internal Circuit
VOUT Pin Voltage
Operate
Set value
Stop
VSS level
Current Consumption
ISS1*1
ISS2
*1. Note that the IC's current consumption increases as much as current flows into the constant current when
the ON / OFF pin is connected to the VIN pin and the S-1315 Series A / C type is operating (refer to
Figure 17).
VIN
ON / OFF
VIN
ON / OFF
VSS
Figure 17
S-1315 Series A / C type
VSS
Figure 18
S-1315 Series B / D type
19
5.5 V INPUT, 200 mA, OUTPUT CAPACITOR-LESS VOLTAGE REGULATOR
Rev.1.4_00
S-1315 Series
4.
Discharge shunt function (S-1315 Series A / B type)
The S-1315 Series A / B type has a built-in discharge shunt circuit to discharge the output capacitance. The output
capacitance is discharged as follows so that the VOUT pin reaches the VSS level.
(1) The ON / OFF pin is set to OFF level.
(2) The output transistor is turned off.
(3) The discharge shunt circuit is turned on.
(4) The output capacitor discharges.
Since the S-1315 Series C / D type does not have a discharge shunt circuit, the VOUT pin is set to the VSS level
through several MΩ internal divided resistors between the VOUT pin and the VSS pin. The S-1315 Series A / B type
allows the VOUT pin to reach the VSS level rapidly due to the discharge shunt circuit.
S-1315 Series
Output transistor: OFF
*1
VOUT
VIN
Discharge shunt circuit
: ON
*1
ON / OFF
ON / OFF circuit
Output
capacitor
(CL)
ON / OFF Pin
: OFF
Current flow
GND
VSS
*1. Parasitic diode
Figure 19
5.
Constant current source pull-down (S-1315 Series A / C type)
The ON / OFF pin is internally pulled down to the VSS pin in the floating status, so the VOUT pin is set to the VSS level.
Note that the IC's current consumption increases as much as current flows into the constant current of 0.1 μA typ.
when the ON / OFF pin is connected to the VIN pin.
20
Rev.1.4_00
6.
5.5 V INPUT, 200 mA, OUTPUT CAPACITOR-LESS VOLTAGE REGULATOR
S-1315 Series
Overcurrent protection circuit
The S-1315 Series includes an overcurrent protection circuit having the characteristics shown in "1. Output voltage
vs. Output current (When load current increases) (Ta = +25°C)" in " Characteristics (Typical Data)", in order to
protect the output transistor against an excessive output current and short circuiting between the VOUT pin and the
VSS pin. The current (Ishort) when the output pin is short-circuited is internally set at approx. 50 mA typ., and the normal
value is restored for the output voltage, if releasing a short circuit once.
Caution This overcurrent protection circuit does not work as for thermal protection. If this IC long keeps
short circuiting inside, pay attention to the conditions of input voltage and load current so that,
under the usage conditions including short circuit, the loss of the IC will not exceed power
dissipation of the package.
21
5.5 V INPUT, 200 mA, OUTPUT CAPACITOR-LESS VOLTAGE REGULATOR
Rev.1.4_00
S-1315 Series
Precautions
• Wiring patterns for the VIN pin, the VOUT pin and GND should be designed so that the impedance is low. When
mounting an output capacitor between the VOUT pin and the VSS pin (CL) and the capacitor for stabilizing the input
between the VIN pin and the VSS pin (CIN), the distance from the capacitors to these pins should be as short as
possible.
• Note that generally the output voltage may increase when a series regulator is used at low load current (0.1 mA or
less).
• Note that generally the output voltage may increase due to the leakage current from an output driver when a series
regulator is used at high temperature.
• Note that the output voltage may increase due to the leakage current from an output driver even if the ON / OFF pin is
at OFF level when a series regulator is used at high temperature.
• Generally a series regulator may cause oscillation, depending on the selection of external parts. The following
conditions are recommended for the S-1315 Series. However, be sure to perform sufficient evaluation under the actual
usage conditions for selection, including evaluation of temperature characteristics. Refer to "5. Example of
equivalent series resistance vs. Output current characteristics (Ta = +25°C)" in " Reference Data" for the
equivalent series resistance (RESR) of the output capacitor.
Input capacitor (CIN):
Output capacitor (CL):
0.1 μF or more
Unnecessary or an output capacitor which is 10 μF or less.
• The voltage regulator may oscillate when the impedance of the power supply is high and the input capacitance is small
or an input capacitor is not connected.
• If the output capacitance is small, power supply's fluctuation and the characteristics of load fluctuation become worse.
Sufficiently evaluate the output voltage's fluctuation with the actual device.
• Overshoot may occur in the output voltage momentarily if the voltage is rapidly raised at power-on or when the power
supply fluctuates. Sufficiently evaluate the output voltage at power-on with the actual device.
• Output voltage noise may increase when the output current is low.
• The application conditions for the input voltage, the output voltage, and the load current should not exceed the
package power dissipation.
• Do not apply an electrostatic discharge to this IC that exceeds the performance ratings of the built-in electrostatic
protection circuit.
• In determining the output current, attention should be paid to the output current value specified in Table 11 in
" Electrical Characteristics" and footnote *5 of the table.
• ABLIC Inc. claims no responsibility for any disputes arising out of or in connection with any infringement by products
including this IC of patents owned by a third party.
22
5.5 V INPUT, 200 mA, OUTPUT CAPACITOR-LESS VOLTAGE REGULATOR
S-1315 Series
Rev.1.4_00
Characteristics (Typical Data)
1.
Output voltage vs. Output current (When load current increases) (Ta = +25°C)
1. 1
VOUT = 1.0 V
1.2
1. 2
1.0
0.6
VIN = 1.4 V
3.0 V
2.0 V
1.8 V
0.4
0.2
0
0
1. 3
5.0
4.5
4.0
3.5
3.0
2.5
2.0
1.5
1.0
0.5
0
VOUT [V]
100
200
300
IOUT [mA]
400
500
400
500
Remark
VIN = 5.5 V
5.2 V
4.7 V
100
200
300
IOUT [mA]
400
In determining the output current, attention should
be paid to the following.
1. The minimum output current value and
footnote *5 in Table 11 in " Electrical
Characteristics"
2. The package power dissipation
500
Output voltage vs. Input voltage (Ta = +25°C)
VOUT = 1.0 V
2. 2
3.0
1.0
2.5
0.8
IOUT = 1 mA
IOUT = 30 mA
IOUT = 50 mA
IOUT = 100 mA
0.6
0.4
0.2
2.0
IOUT = 1 mA
IOUT = 30 mA
IOUT = 50 mA
IOUT = 100 mA
1.5
1.0
0.5
0
0
0
2. 3
VOUT = 2.8 V
1.2
VOUT [V]
VOUT [V]
2. 1
VOUT [V]
3.3 V
3.8 V
4.8 V
VOUT = 4.2 V
0
2.
VOUT [V]
VOUT [V]
0.8
VOUT = 2.8 V
3.5
3.0
2.5
2.0
VIN = 5.5 V
1.5
1.0
0.5
0
100
200
300
0
IOUT [mA]
1.0
2.0
3.0
4.0
VIN [V]
5.0
6.0
0
1.0
2.0
3.0
4.0
VIN [V]
5.0
6.0
VOUT = 4.2 V
4.5
4.0
3.5
3.0
2.5
2.0
1.5
1.0
0.5
0
IOUT = 1 mA
IOUT = 30 mA
IOUT = 50 mA
IOUT = 100 mA
0
1.0
2.0
3.0
4.0
VIN [V]
5.0
6.0
23
5.5 V INPUT, 200 mA, OUTPUT CAPACITOR-LESS VOLTAGE REGULATOR
Rev.1.4_00
S-1315 Series
Dropout voltage vs. Output current
Vdrop [V]
3. 1
3. 3
VOUT = 1.0 V
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0
0
50
3. 2
Vdrop [V]
3.
Ta = +85°C
Ta = +25°C
Ta = −40°C
100
150
IOUT [mA]
200
250
200
250
VOUT = 4.2 V
0.30
Vdrop [V]
0.25
Ta = +85°C
Ta = +25°C
Ta = −40°C
0.20
0.15
0.10
0.05
0
0
Vdrop [V]
4.
100
150
IOUT [mA]
Dropout voltage vs. Set output voltage
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0
IOUT = 200 mA
100 mA
50 mA
30 mA
1 mA
1.0
24
50
1.5
2.0
2.5 3.0 3.5
VOUT(S) [V]
4.0
4.5
VOUT = 2.8 V
0.35
0.30
Ta = +85°C
0.25
Ta = +25°C
0.20
Ta = −40°C
0.15
0.10
0.05
0
0
50
100
150
IOUT [mA]
200
250
Rev.1.4_00
Output voltage vs. Ambient temperature
5. 1
VOUT [V]
1.20
1.15
1.10
1.05
1.00
0.95
0.90
0.85
0.80
5. 3
5. 2
−40 −25
0
25
Ta [°C]
50
75 85
0
25
Ta [°C]
50
75 85
VOUT = 2.8 V
3.00
2.95
2.90
2.85
2.80
2.75
2.70
2.65
2.60
2.55
2.50
−40 −25
0
25
Ta [°C]
75 85
50
VOUT = 4.2 V
4.40
4.35
4.30
4.25
4.20
4.15
4.10
4.05
4.00
VOUT [V]
6.
VOUT = 1.0 V
VOUT [V]
5.
5.5 V INPUT, 200 mA, OUTPUT CAPACITOR-LESS VOLTAGE REGULATOR
S-1315 Series
−40 −25
Current consumption vs. Input voltage
6. 1
VOUT = 1.0 V
6. 2
Ta = +25°C
10
ISS1 [μA]
ISS1 [μA]
20
6
4
2
15
10
5
0
0
0
ISS1 [μA]
Ta = +25°C
25
8
6. 3
VOUT = 2.8 V
1
2
3
VIN [V]
4
5
6
0
1
2
3
VIN [V]
4
5
6
VOUT = 4.2 V
Ta = +25°C
50
45
40
35
30
25
20
15
10
5
0
0
1
2
3
VIN [V]
4
5
6
25
5.5 V INPUT, 200 mA, OUTPUT CAPACITOR-LESS VOLTAGE REGULATOR
Rev.1.4_00
S-1315 Series
Current consumption vs. Ambient temperature
7. 1
ISS1 [μA]
9
8
7
6
5
4
3
2
1
0
7. 3
7. 2
−40 −25
0
25
Ta [°C]
50
75 85
0
25
Ta [°C]
50
75 85
VOUT = 2.8 V
9
8
7
6
5
4
3
2
1
0
−40 −25
0
−40 −25
VOUT = 1.0 V
8. 2
75 85
VOUT = 2.8 V
100
IOUT = 30 mA
80
60
IOUT = 1 mA
IOUT = 150 mA
IOUT = 50 mA
40
20
0
10
8. 3
100
1k
10k
100k
Frequency [Hz]
1M
VOUT = 4.2 V
VIN = 5.2 V, CL = 0.1 μF
100
IOUT = 150 mA
80
60
40
IOUT = 1 mA
IOUT = 30 mA
IOUT = 50 mA
20
0
10
100
1k
10k
100k
Frequency [Hz]
VIN = 3.8 V, CL = 0.1 μF
Ripple Rejection [dB]
Ripple Rejection [dB]
VIN = 2.0 V, CL = 0.1 μF
Ripple Rejection [dB]
50
Ripple rejection (Ta = +25°C)
8. 1
26
25
Ta [°C]
VOUT = 4.2 V
9
8
7
6
5
4
3
2
1
0
ISS1 [μA]
8.
VOUT = 1.0 V
ISS1 [μA]
7.
1M
100
IOUT = 150 mA
80
60
40
IOUT = 1 mA
IOUT = 30 mA
IOUT = 50 mA
20
0
10
100
1k
10k
100k
Frequency [Hz]
1M
Rev.1.4_00
Ripple rejection vs. Output capacitance (Ta = +25°C)
9. 1
VOUT = 1.0 V
9. 2
VOUT = 2.8 V
100
80
60
CL = 0 μF
40
CL = 0.1 μF
20
CL = 1 μF
0
10
9. 3
100
1k
10k
100k
Frequency [Hz]
VIN = 3.8 V, IOUT = 30 mA
Ripple Rejection [dB]
Ripple Rejection [dB]
VIN = 2.0 V, IOUT = 30 mA
1M
100
80
60
CL = 0 μF
40
CL = 0.1 μF
20
CL = 1 μF
0
10
100
1k
10k
100k
Frequency [Hz]
1M
VOUT = 4.2 V
VIN = 5.2 V, IOUT = 30 mA
Ripple Rejection [dB]
9.
5.5 V INPUT, 200 mA, OUTPUT CAPACITOR-LESS VOLTAGE REGULATOR
S-1315 Series
100
80
60
CL = 0 μF
40
CL = 0.1 μF
20
CL = 1 μF
0
10
100
1k
10k
100k
Frequency [Hz]
1M
27
5.5 V INPUT, 200 mA, OUTPUT CAPACITOR-LESS VOLTAGE REGULATOR
Rev.1.4_00
S-1315 Series
Reference Data
Transient response characteristics when input (Ta = +25°C)
VOUT = 1.0 V
VIN = 2.0 V ↔ 3.0 V, CL = 0 μF, IOUT = 30 mA, tr = tf = 5.0 μs
4
1.20
1.10
3
1.15
2
1.10
1
1.05
VOUT
1.00
0
1.00
VOUT
0
0.95
−1
0.95
−1
−2
0.90
−2
−40 −20 0
20 40 60 80 100 120 140
t [μs]
3
VOUT
2
2.75
1
2.70
0
−40 −20 0
1. 3
3
2.85
2.80
VOUT
2
2.75
1
2.70
0
4.35
4
4.30
3
VOUT
−40 −20 0
5
2
20 40 60 80 100 120 140
t [μs]
VIN [V]
VIN
4.15
4.10
4
−40 −20 0
20 40 60 80 100 120 140
t [μs]
VIN = 4.5 V ↔ 5.5 V, CL = 0.1 μF, IOUT = 30 mA, tr = tf = 5.0 μs
6
4.40
VOUT [V]
4.20
VIN
VOUT = 4.2 V
4.30
4.25
2.90
20 40 60 80 100 120 140
t [μs]
VIN = 4.5 V ↔ 5.5 V, CL = 0 μF, IOUT = 30 mA, tr = tf = 5.0 μs
6
4.40
4.35
5
2.95
VOUT [V]
4
2.85
2.80
20 40 60 80 100 120 140
t [μs]
VIN = 3.8 V ↔ 4.8 V, CL = 0.1 μF, IOUT = 30 mA, tr = tf = 5.0 μs
6
3.00
5
VIN
2.90
−40 −20 0
VOUT = 2.8 V
VIN [V]
2.95
VOUT [V]
1
1.05
VIN = 3.8 V ↔ 4.8 V, CL = 0 μF, IOUT = 30 mA, tr = tf = 5.0 μs
6
3.00
VOUT [V]
2
0.90
1. 2
28
3
VIN
VIN [V]
VIN
VIN [V]
VOUT [V]
VOUT [V]
1.15
VIN = 2.0 V ↔ 3.0 V, CL = 0.1 μF, IOUT = 30 mA, tr = tf = 5.0 μs
4
1.20
VIN [V]
1. 1
4.25
4.20
1
4.15
0
4.10
5
VIN
4
3
VOUT
2
1
0
−40 −20 0
20 40 60 80 100 120 140
t [μs]
VIN [V]
1.
Rev.1.4_00
Transient response characteristics of load (Ta = +25°C)
VOUT = 1.0 V
CL = 0.1 μF
VOUT
CL = 1 μF
−40 −20 0
20 40 60 80 100 120 140
t [μs]
CL = 0 μF
CL = 0.1 μF
VOUT
CL = 1 μF
−40 −20 0
20 40 60 80 100 120 140
t [μs]
IOUT
CL = 0 μF
VOUT
CL = 0.1 μF
CL = 1 μF
−40 −20 0
20 40 60 80 100 120 140
t [μs]
100
50
0
−50
−100
−150
−200
−250
−300
IOUT [mA]
VOUT [V]
VOUT
CL = 0.1 μF
CL = 1 μF
−20 −10 0
10 20 30 40 50 60 70
t [μs]
VIN = 3.8 V, CIN = 0.1 μF, IOUT = 50 mA ↔ 100 mA, tr = tf = 0.5 μs
3.4
3.3
3.2
3.1
3.0
2.9
2.8
2.7
2.6
IOUT
CL = 0 μF
VOUT
CL = 0.1 μF
CL = 1 μF
−20 −10 0
10 20 30 40 50 60 70
t [μs]
150
100
50
0
−50
−100
−150
−200
−250
VOUT = 4.2 V
VIN = 5.2 V, CIN = 0.1 μF, IOUT = 5.0 mA ↔ 50 mA, tr = tf = 2.0 μs
4.8
4.7
4.6
4.5
4.4
4.3
4.2
4.1
4.0
CL = 0 μF
150
100
50
0
−50
−100
−150
−200
−250
IOUT [mA]
IOUT
100
50
0
−50
−100
−150
−200
−250
−300
IOUT [mA]
VOUT [V]
2. 3
IOUT
VOUT = 2.8 V
VIN = 3.8 V, CIN = 0.1 μF, IOUT = 5.0 mA ↔ 50 mA, tr = tf = 2.0 μs
3.4
3.3
3.2
3.1
3.0
2.9
2.8
2.7
2.6
1.6
1.5
1.4
1.3
1.2
1.1
1.0
0.9
0.8
IOUT [mA]
CL = 0 μF
100
50
0
−50
−100
−150
−200
−250
−300
VIN = 5.2 V, CIN = 0.1 μF, IOUT = 50 mA ↔ 100 mA, tr = tf = 0.5 μs
4.8
4.7
4.6
4.5
4.4
4.3
4.2
4.1
4.0
IOUT
CL = 0 μF
VOUT
CL = 0.1 μF
CL = 1 μF
−20 −10 0
10 20 30 40 50 60 70
t [μs]
150
100
50
0
−50
−100
−150
−200
−250
IOUT [mA]
2. 2
IOUT
IOUT [mA]
1.6
1.5
1.4
1.3
1.2
1.1
1.0
0.9
0.8
VIN = 2.0 V, CIN = 0.1 μF, IOUT = 50 mA ↔ 100 mA, tr = tf = 0.5 μs
VOUT [V]
VOUT [V]
VIN = 2.0 V, CIN = 0.1 μF, IOUT = 5.0 mA ↔ 50 mA, tr = tf = 2.0 μs
VOUT [V]
2. 1
VOUT [V]
2.
5.5 V INPUT, 200 mA, OUTPUT CAPACITOR-LESS VOLTAGE REGULATOR
S-1315 Series
29
5.5 V INPUT, 200 mA, OUTPUT CAPACITOR-LESS VOLTAGE REGULATOR
Rev.1.4_00
S-1315 Series
Transient response characteristics of ON / OFF pin (when rising) (Ta = +25°C)
VOUT = 1.0 V
1.0
0.5
IOUT = 30 mA
IOUT = 200 mA
0
1.5
IOUT = 1 mA
1.0
0.5
−2
0
−3
−0.5
VOUT
IOUT = 30 mA
IOUT = 200 mA
−100 0 100 200 300 400 500 600 700 800
t [μs]
1
0
−1
−2
−3
VOUT = 2.8 V
VON / OFF [V]
VIN = 3.8 V, CIN = 0.1 μF, CL = 1.0 μF, VON / OFF = 0 V → 3.8 V
6.3
5
4
5.6
VON / OFF
3
4.9
2
4.2
IOUT = 1 mA
1
3.5
VOUT
0
2.8
−1
2.1
−2
1.4
IOUT = 30 mA
−3
0.7
IOUT = 200 mA
−4
0
−0.7
−5
−100 0 100 200 300 400 500 600 700 800
t [μs]
VOUT = 4.2 V
VIN = 5.2 V, CIN = 0.1 μF, CL = 0 μF, VON / OFF = 0 V → 5.2 V
6.3
6
5
5.6
VON / OFF
4
4.9
3
4.2
2
VOUT
3.5
1
2.8
0
2.1
IOUT = 1 mA
−1
1.4
IOUT = 30 mA
−2
0.7
IOUT = 200 mA
−3
0
−0.7
−4
−100 0 100 200 300 400 500 600 700 800
t [μs]
VIN = 5.2 V, CIN = 0.1 μF, CL = 1.0 μF, VON / OFF = 0 V → 5.2 V
6.3
6
5
5.6
V
ON
/
OFF
4
4.9
3
4.2
2
3.5
VOUT
1
2.8
0
2.1
IOUT = 1 mA
−1
1.4
IOUT = 30 mA
−2
0.7
IOUT = 200 mA
−3
0
−0.7
−4
−100 0 100 200 300 400 500 600 700 800
t [μs]
VOUT [V]
VOUT [V]
−1
VIN = 3.8 V, CIN = 0.1 μF, CL = 0 μF, VON / OFF = 0 V → 3.8 V
6.3
5
4
5.6
VON / OFF
3
4.9
2
4.2
IOUT = 1 mA
1
3.5
VOUT
0
2.8
−1
2.1
−2
1.4
IOUT = 30 mA
−3
0.7
IOUT = 200 mA
−4
0
−0.7
−5
−100 0 100 200 300 400 500 600 700 800
t [μs]
3. 3
30
0
VOUT [V]
VOUT [V]
3. 2
−100 0 100 200 300 400 500 600 700 800
t [μs]
1
VON / OFF [V]
−0.5
VOUT
VOUT [V]
IOUT = 1 mA
VON / OFF [V]
1.5
VIN = 2.0 V, CIN = 0.1 μF, CL = 1.0 μF, VON / OFF = 0 V → 2.0 V
2.5
3
VON / OFF
2.0
2
VON / OFF [V]
VOUT [V]
VIN = 2.0 V, CIN = 0.1 μF, CL = 0 μF, VON / OFF = 0 V → 2.0 V
2.5
3
VON / OFF
2.0
2
VON / OFF [V]
3. 1
VON / OFF [V]
3.
Rev.1.4_00
Transient response characteristics of ON / OFF pin (when falling) (Ta = +25°C)
VON / OFF [V]
VOUT [V]
VOUT [V]
VON / OFF [V]
VON / OFF [V]
VIN = 5.2 V, CIN = 0.1 μF, CL = 1.0 μF, VON / OFF = 5.2 V → 0 V
8
6
7
4
6
2
VON / OFF
5
0
IOUT = 1 mA
4
−2
IOUT = 30 mA
3
−4
2
−6
IOUT = 200 mA
1
−8
VOUT
0
−10
−1
−12
−20 0 20 40 60 80 100 120 140 160 180
t [μs]
VON / OFF [V]
VOUT [V]
VIN = 3.8 V, CIN = 0.1 μF, CL = 1.0 μF, VON / OFF = 3.8 V → 0 V
6.3
4
5.6
3
4.9
2
4.2
1
VON / OFF
3.5
0
IOUT = 1 mA
−1
2.8
IOUT = 30 mA
−2
2.1
−3
1.4
IOUT = 200 mA
−4
0.7
VOUT
−5
0
−0.7
−6
−20 0 20 40 60 80 100 120 140 160 180
t [μs]
VOUT = 4.2 V
VIN = 5.2 V, CIN = 0.1 μF, CL = 0 μF, VON / OFF = 5.2 V → 0 V
8
6
7
4
6
2
VON / OFF
5
0
IOUT = 1 mA
4
−2
3
−4
IOUT = 30 mA
2
−6
IOUT = 200 mA
1
−8
VOUT
0
−10
−1
−12
−10 0 10 20 30 40 50 60 70 80
t [μs]
5.
VIN = 2.0 V, CIN = 0.1 μF, CL = 1.0 μF, VON / OFF = 2.0 V → 0 V
3.0
3
2.5
2
2.0
1
VON / OFF
1.5
0
IOUT = 1 mA
1.0
−1
IOUT = 30 mA
0.5
−2
IOUT = 200 mA
0
−3
VOUT
−0.5
−4
−20 0 20 40 60 80 100 120 140 160 180
t [μs]
VOUT = 2.8 V
VIN = 3.8 V, CIN = 0.1 μF, CL = 0 μF, VON / OFF = 3.8 V → 0 V
6.3
4
5.6
3
4.9
2
4.2
1
VON / OFF
3.5
0
IOUT = 1 mA
−1
2.8
−2
2.1
IOUT = 30 mA
−3
1.4
IOUT = 200 mA
−4
0.7
VOUT
−5
0
−0.7
−6
−10 0 10 20 30 40 50 60 70 80
t [μs]
4. 3
VON / OFF [V]
VIN = 2.0 V, CIN = 0.1 μF, CL = 0 μF, VON / OFF = 2.0 V → 0 V
3.0
3
2.5
2
2.0
1
VON / OFF
1.5
0
IOUT = 1 mA
1.0
−1
IOUT = 30 mA
0.5
−2
IOUT = 200 mA
0
−3
VOUT
−0.5
−4
−10 0 10 20 30 40 50 60 70 80
t [μs]
4. 2
VOUT [V]
VOUT = 1.0 V
VOUT [V]
VOUT [V]
4. 1
VON / OFF [V]
4.
5.5 V INPUT, 200 mA, OUTPUT CAPACITOR-LESS VOLTAGE REGULATOR
S-1315 Series
Example of equivalent series resistance vs. Output current characteristics (Ta = +25°C)
CIN = CL = 0.1 μF
100
RESR [Ω]
VIN
VOUT
CIN
Stable
ON / OFF
0
0.01
S-1315 Series
VSS
200
CL
*1
RESR
IOUT [mA]
*1.
Figure 20
CL: Murata Manufacturing Co.,Ltd. GRM31CR72E104KW03L (0.1 μF)
Figure 21
31
5.5 V INPUT, 200 mA, OUTPUT CAPACITOR-LESS VOLTAGE REGULATOR
Rev.1.4_00
S-1315 Series
Marking Specifications
1.
SOT-23-5
Top view
5
(1) to (3):
(4):
4
Product code (Refer to Product name vs. Product code)
Lot number
(1) (2) (3) (4)
1
2
3
Product name vs. Product code
1. 1
S-1315 Series A type
Product Name
S-1315A10-M5T1U3
S-1315A11-M5T1U3
S-1315A12-M5T1U3
S-1315A13-M5T1U3
S-1315A14-M5T1U3
S-1315A15-M5T1U3
S-1315A16-M5T1U3
S-1315A17-M5T1U3
S-1315A18-M5T1U3
S-1315A1J-M5T1U3
S-1315A19-M5T1U3
S-1315A20-M5T1U3
S-1315A21-M5T1U3
S-1315A22-M5T1U3
S-1315A23-M5T1U3
S-1315A24-M5T1U3
S-1315A25-M5T1U3
S-1315A26-M5T1U3
S-1315A27-M5T1U3
S-1315A28-M5T1U3
S-1315A2J-M5T1U3
S-1315A29-M5T1U3
S-1315A30-M5T1U3
S-1315A31-M5T1U3
S-1315A32-M5T1U3
S-1315A33-M5T1U3
S-1315A34-M5T1U3
S-1315A35-M5T1U3
S-1315A36-M5T1U3
S-1315A37-M5T1U3
S-1315A38-M5T1U3
S-1315A39-M5T1U3
S-1315A40-M5T1U3
S-1315A41-M5T1U3
S-1315A42-M5T1U3
32
1. 2
(1)
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
Product Code
(2)
(3)
J
A
J
B
J
C
J
D
J
E
J
F
J
G
J
H
J
I
J
J
J
K
J
L
J
M
J
N
J
O
J
P
J
Q
J
R
J
S
J
T
J
U
J
V
J
W
J
X
J
Y
J
Z
J
2
J
3
J
4
J
5
J
6
J
7
J
8
J
9
J
1
S-1315 Series B type
Product Name
S-1315B10-M5T1U3
S-1315B11-M5T1U3
S-1315B12-M5T1U3
S-1315B13-M5T1U3
S-1315B14-M5T1U3
S-1315B15-M5T1U3
S-1315B16-M5T1U3
S-1315B17-M5T1U3
S-1315B18-M5T1U3
S-1315B1J-M5T1U3
S-1315B19-M5T1U3
S-1315B20-M5T1U3
S-1315B21-M5T1U3
S-1315B22-M5T1U3
S-1315B23-M5T1U3
S-1315B24-M5T1U3
S-1315B25-M5T1U3
S-1315B26-M5T1U3
S-1315B27-M5T1U3
S-1315B28-M5T1U3
S-1315B2J-M5T1U3
S-1315B29-M5T1U3
S-1315B30-M5T1U3
S-1315B31-M5T1U3
S-1315B32-M5T1U3
S-1315B33-M5T1U3
S-1315B34-M5T1U3
S-1315B35-M5T1U3
S-1315B36-M5T1U3
S-1315B37-M5T1U3
S-1315B38-M5T1U3
S-1315B39-M5T1U3
S-1315B40-M5T1U3
S-1315B41-M5T1U3
S-1315B42-M5T1U3
(1)
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
Product Code
(2)
(3)
K
A
K
B
K
C
K
D
K
E
K
F
K
G
K
H
K
I
K
J
K
K
K
L
K
M
K
N
K
O
K
P
K
Q
K
R
K
S
K
T
K
U
K
V
K
W
K
X
K
Y
K
Z
K
2
K
3
K
4
K
5
K
6
K
7
K
8
K
9
K
1
Rev.1.4_00
1. 3
5.5 V INPUT, 200 mA, OUTPUT CAPACITOR-LESS VOLTAGE REGULATOR
S-1315 Series
S-1315 Series C type
Product Name
S-1315C10-M5T1U3
S-1315C11-M5T1U3
S-1315C12-M5T1U3
S-1315C13-M5T1U3
S-1315C14-M5T1U3
S-1315C15-M5T1U3
S-1315C16-M5T1U3
S-1315C17-M5T1U3
S-1315C18-M5T1U3
S-1315C1J-M5T1U3
S-1315C19-M5T1U3
S-1315C20-M5T1U3
S-1315C21-M5T1U3
S-1315C22-M5T1U3
S-1315C23-M5T1U3
S-1315C24-M5T1U3
S-1315C25-M5T1U3
S-1315C26-M5T1U3
S-1315C27-M5T1U3
S-1315C28-M5T1U3
S-1315C2J-M5T1U3
S-1315C29-M5T1U3
S-1315C30-M5T1U3
S-1315C31-M5T1U3
S-1315C32-M5T1U3
S-1315C33-M5T1U3
S-1315C34-M5T1U3
S-1315C35-M5T1U3
S-1315C36-M5T1U3
S-1315C37-M5T1U3
S-1315C38-M5T1U3
S-1315C39-M5T1U3
S-1315C40-M5T1U3
S-1315C41-M5T1U3
S-1315C42-M5T1U3
1. 4
Product Code
(1)
(2)
(3)
W
L
A
W
L
B
W
L
C
W
L
D
W
L
E
W
L
F
W
L
G
W
L
H
W
L
I
W
L
J
W
L
K
W
L
L
W
L
M
W
L
N
W
L
O
W
L
P
W
L
Q
W
L
R
W
L
S
W
L
T
W
L
U
W
L
V
W
L
W
W
L
X
W
L
Y
W
L
Z
W
L
2
W
L
3
W
L
4
W
L
5
W
L
6
W
L
7
W
L
8
W
L
9
W
L
1
S-1315 Series D type
Product Name
S-1315D10-M5T1U3
S-1315D11-M5T1U3
S-1315D12-M5T1U3
S-1315D13-M5T1U3
S-1315D14-M5T1U3
S-1315D15-M5T1U3
S-1315D16-M5T1U3
S-1315D17-M5T1U3
S-1315D18-M5T1U3
S-1315D1J-M5T1U3
S-1315D19-M5T1U3
S-1315D20-M5T1U3
S-1315D21-M5T1U3
S-1315D22-M5T1U3
S-1315D23-M5T1U3
S-1315D24-M5T1U3
S-1315D25-M5T1U3
S-1315D26-M5T1U3
S-1315D27-M5T1U3
S-1315D28-M5T1U3
S-1315D2J-M5T1U3
S-1315D29-M5T1U3
S-1315D30-M5T1U3
S-1315D31-M5T1U3
S-1315D32-M5T1U3
S-1315D33-M5T1U3
S-1315D34-M5T1U3
S-1315D35-M5T1U3
S-1315D36-M5T1U3
S-1315D37-M5T1U3
S-1315D38-M5T1U3
S-1315D39-M5T1U3
S-1315D40-M5T1U3
S-1315D41-M5T1U3
S-1315D42-M5T1U3
Product Code
(1)
(2)
(3)
W
M
A
W
M
B
W
M
C
W
M
D
W
M
E
W
M
F
W
M
G
W
M
H
W
M
I
W
M
J
W
M
K
W
M
L
W
M
M
W
M
N
W
M
O
W
M
P
W
M
Q
W
M
R
W
M
S
W
M
T
W
M
U
W
M
V
W
M
W
W
M
X
W
M
Y
W
M
Z
W
M
2
W
M
3
W
M
4
W
M
5
W
M
6
W
M
7
W
M
8
W
M
9
W
M
1
33
5.5 V INPUT, 200 mA, OUTPUT CAPACITOR-LESS VOLTAGE REGULATOR
Rev.1.4_00
S-1315 Series
2.
HSNT-6 (1212)
Top view
6
5
(1) to (3):
(4), (5):
4
Product code (Refer to Product name vs. Product code)
Lot number
(1) (2) (3)
(4) (5)
1
2
3
Product name vs. Product code
2. 1
S-1315 Series A type
Product Name
S-1315A10-A6T2U3
S-1315A11-A6T2U3
S-1315A12-A6T2U3
S-1315A13-A6T2U3
S-1315A14-A6T2U3
S-1315A15-A6T2U3
S-1315A16-A6T2U3
S-1315A17-A6T2U3
S-1315A18-A6T2U3
S-1315A1J-A6T2U3
S-1315A19-A6T2U3
S-1315A20-A6T2U3
S-1315A21-A6T2U3
S-1315A22-A6T2U3
S-1315A23-A6T2U3
S-1315A24-A6T2U3
S-1315A25-A6T2U3
S-1315A26-A6T2U3
S-1315A27-A6T2U3
S-1315A28-A6T2U3
S-1315A2J-A6T2U3
S-1315A29-A6T2U3
S-1315A30-A6T2U3
S-1315A31-A6T2U3
S-1315A32-A6T2U3
S-1315A33-A6T2U3
S-1315A34-A6T2U3
S-1315A35-A6T2U3
S-1315A36-A6T2U3
S-1315A37-A6T2U3
S-1315A38-A6T2U3
S-1315A39-A6T2U3
S-1315A40-A6T2U3
S-1315A41-A6T2U3
S-1315A42-A6T2U3
34
2. 2
(1)
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
Product Code
(2)
(3)
J
A
J
B
J
C
J
D
J
E
J
F
J
G
J
H
J
I
J
J
J
K
J
L
J
M
J
N
J
O
J
P
J
Q
J
R
J
S
J
T
J
U
J
V
J
W
J
X
J
Y
J
Z
J
2
J
3
J
4
J
5
J
6
J
7
J
8
J
9
J
1
S-1315 Series B type
Product Name
S-1315B10-A6T2U3
S-1315B11-A6T2U3
S-1315B12-A6T2U3
S-1315B13-A6T2U3
S-1315B14-A6T2U3
S-1315B15-A6T2U3
S-1315B16-A6T2U3
S-1315B17-A6T2U3
S-1315B18-A6T2U3
S-1315B1J-A6T2U3
S-1315B19-A6T2U3
S-1315B20-A6T2U3
S-1315B21-A6T2U3
S-1315B22-A6T2U3
S-1315B23-A6T2U3
S-1315B24-A6T2U3
S-1315B25-A6T2U3
S-1315B26-A6T2U3
S-1315B27-A6T2U3
S-1315B28-A6T2U3
S-1315B2J-A6T2U3
S-1315B29-A6T2U3
S-1315B30-A6T2U3
S-1315B31-A6T2U3
S-1315B32-A6T2U3
S-1315B33-A6T2U3
S-1315B34-A6T2U3
S-1315B35-A6T2U3
S-1315B36-A6T2U3
S-1315B37-A6T2U3
S-1315B38-A6T2U3
S-1315B39-A6T2U3
S-1315B40-A6T2U3
S-1315B41-A6T2U3
S-1315B42-A6T2U3
(1)
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
Product Code
(2)
(3)
K
A
K
B
K
C
K
D
K
E
K
F
K
G
K
H
K
I
K
J
K
K
K
L
K
M
K
N
K
O
K
P
K
Q
K
R
K
S
K
T
K
U
K
V
K
W
K
X
K
Y
K
Z
K
2
K
3
K
4
K
5
K
6
K
7
K
8
K
9
K
1
Rev.1.4_00
2. 3
5.5 V INPUT, 200 mA, OUTPUT CAPACITOR-LESS VOLTAGE REGULATOR
S-1315 Series
S-1315 Series C type
Product Name
S-1315C10-A6T2U3
S-1315C11-A6T2U3
S-1315C12-A6T2U3
S-1315C13-A6T2U3
S-1315C14-A6T2U3
S-1315C15-A6T2U3
S-1315C16-A6T2U3
S-1315C17-A6T2U3
S-1315C18-A6T2U3
S-1315C1J-A6T2U3
S-1315C19-A6T2U3
S-1315C20-A6T2U3
S-1315C21-A6T2U3
S-1315C22-A6T2U3
S-1315C23-A6T2U3
S-1315C24-A6T2U3
S-1315C25-A6T2U3
S-1315C26-A6T2U3
S-1315C27-A6T2U3
S-1315C28-A6T2U3
S-1315C2J-A6T2U3
S-1315C29-A6T2U3
S-1315C30-A6T2U3
S-1315C31-A6T2U3
S-1315C32-A6T2U3
S-1315C33-A6T2U3
S-1315C34-A6T2U3
S-1315C35-A6T2U3
S-1315C36-A6T2U3
S-1315C37-A6T2U3
S-1315C38-A6T2U3
S-1315C39-A6T2U3
S-1315C40-A6T2U3
S-1315C41-A6T2U3
S-1315C42-A6T2U3
2. 4
Product Code
(1)
(2)
(3)
W
L
A
W
L
B
W
L
C
W
L
D
W
L
E
W
L
F
W
L
G
W
L
H
W
L
I
W
L
J
W
L
K
W
L
L
W
L
M
W
L
N
W
L
O
W
L
P
W
L
Q
W
L
R
W
L
S
W
L
T
W
L
U
W
L
V
W
L
W
W
L
X
W
L
Y
W
L
Z
W
L
2
W
L
3
W
L
4
W
L
5
W
L
6
W
L
7
W
L
8
W
L
9
W
L
1
S-1315 Series D type
Product Name
S-1315D10-A6T2U3
S-1315D11-A6T2U3
S-1315D12-A6T2U3
S-1315D13-A6T2U3
S-1315D14-A6T2U3
S-1315D15-A6T2U3
S-1315D16-A6T2U3
S-1315D17-A6T2U3
S-1315D18-A6T2U3
S-1315D1J-A6T2U3
S-1315D19-A6T2U3
S-1315D20-A6T2U3
S-1315D21-A6T2U3
S-1315D22-A6T2U3
S-1315D23-A6T2U3
S-1315D24-A6T2U3
S-1315D25-A6T2U3
S-1315D26-A6T2U3
S-1315D27-A6T2U3
S-1315D28-A6T2U3
S-1315D2J-A6T2U3
S-1315D29-A6T2U3
S-1315D30-A6T2U3
S-1315D31-A6T2U3
S-1315D32-A6T2U3
S-1315D33-A6T2U3
S-1315D34-A6T2U3
S-1315D35-A6T2U3
S-1315D36-A6T2U3
S-1315D37-A6T2U3
S-1315D38-A6T2U3
S-1315D39-A6T2U3
S-1315D40-A6T2U3
S-1315D41-A6T2U3
S-1315D42-A6T2U3
Product Code
(1)
(2)
(3)
W
M
A
W
M
B
W
M
C
W
M
D
W
M
E
W
M
F
W
M
G
W
M
H
W
M
I
W
M
J
W
M
K
W
M
L
W
M
M
W
M
N
W
M
O
W
M
P
W
M
Q
W
M
R
W
M
S
W
M
T
W
M
U
W
M
V
W
M
W
W
M
X
W
M
Y
W
M
Z
W
M
2
W
M
3
W
M
4
W
M
5
W
M
6
W
M
7
W
M
8
W
M
9
W
M
1
35
2.9±0.2
1.9±0.2
4
5
1
2
+0.1
0.16 -0.06
3
0.95±0.1
0.4±0.1
No. MP005-A-P-SD-1.3
TITLE
SOT235-A-PKG Dimensions
No.
MP005-A-P-SD-1.3
ANGLE
UNIT
mm
ABLIC Inc.
4.0±0.1(10 pitches:40.0±0.2)
+0.1
ø1.5 -0
+0.2
ø1.0 -0
2.0±0.05
0.25±0.1
4.0±0.1
1.4±0.2
3.2±0.2
3 2 1
4
5
Feed direction
No. MP005-A-C-SD-2.1
TITLE
SOT235-A-Carrier Tape
No.
MP005-A-C-SD-2.1
ANGLE
UNIT
mm
ABLIC Inc.
12.5max.
9.0±0.3
Enlarged drawing in the central part
ø13±0.2
(60°)
(60°)
No. MP005-A-R-SD-1.1
SOT235-A-Reel
TITLE
No.
MP005-A-R-SD-1.1
ANGLE
QTY.
UNIT
mm
ABLIC Inc.
3,000
0.40
1.00±0.05
0.38±0.02
0.40
4
6
3
1
+0.05
0.08 -0.02
1.20±0.04
The heat sink of back side has different electric
potential depending on the product.
Confirm specifications of each product.
Do not use it as the function of electrode.
0.20±0.05
No. PM006-A-P-SD-1.1
TITLE
HSNT-6-B-PKG Dimensions
No.
PM006-A-P-SD-1.1
ANGLE
UNIT
mm
ABLIC Inc.
2.0±0.05
+0.1
ø1.5 -0
4.0±0.1
0.25±0.05
+0.1
ø0.5 -0
0.50±0.05
4.0±0.1
1.32±0.05
3
1
4
6
Feed direction
No. PM006-A-C-SD-2.0
TITLE
HSNT-6-B-C a r r i e r Tape
No.
PM006-A-C-SD-2.0
ANGLE
UNIT
mm
ABLIC Inc.
+1.0
9.0 - 0.0
11.4±1.0
Enlarged drawing in the central part
ø13±0.2
(60°)
(60°)
No. PM006-A-R-SD-1.0
TITLE
HSNT-6-B-Reel
No.
PM006-A-R-SD-1.0
ANGLE
UNIT
QTY.
mm
ABLIC Inc.
5,000
1.04min.
Land Pattern
0.24min.
1.02
0.40±0.02
0.40±0.02
(1.22)
Caution It is recommended to solder the heat sink to a board
in order to ensure the heat radiation.
PKG
Metal Mask Pattern
Aperture ratio
Aperture ratio
Caution
Mask aperture ratio of the lead mounting part is 100%.
Mask aperture ratio of the heat sink mounting part is 40%.
Mask thickness: t0.10mm to 0.12 mm
100%
40%
t0.10mm ~ 0.12 mm
TITLE
HSNT-6-B
-Land Recommendation
PM006-A-L-SD-2.0
No.
ANGLE
No. PM006-A-L-SD-2.0
UNIT
mm
ABLIC Inc.
Disclaimers (Handling Precautions)
1.
All the information described herein (product data, specifications, figures, tables, programs, algorithms and
application circuit examples, etc.) is current as of publishing date of this document and is subject to change without
notice.
2.
The circuit examples and the usages described herein are for reference only, and do not guarantee the success of
any specific mass-production design.
ABLIC Inc. is not liable for any losses, damages, claims or demands caused by the reasons other than the products
described herein (hereinafter "the products") or infringement of third-party intellectual property right and any other
right due to the use of the information described herein.
3.
ABLIC Inc. is not liable for any losses, damages, claims or demands caused by the incorrect information described
herein.
4.
Be careful to use the products within their ranges described herein. Pay special attention for use to the absolute
maximum ratings, operation voltage range and electrical characteristics, etc.
ABLIC Inc. is not liable for any losses, damages, claims or demands caused by failures and / or accidents, etc. due to
the use of the products outside their specified ranges.
5.
Before using the products, confirm their applications, and the laws and regulations of the region or country where they
are used and verify suitability, safety and other factors for the intended use.
6.
When exporting the products, comply with the Foreign Exchange and Foreign Trade Act and all other export-related
laws, and follow the required procedures.
7.
The products are strictly prohibited from using, providing or exporting for the purposes of the development of
weapons of mass destruction or military use. ABLIC Inc. is not liable for any losses, damages, claims or demands
caused by any provision or export to the person or entity who intends to develop, manufacture, use or store nuclear,
biological or chemical weapons or missiles, or use any other military purposes.
8.
The products are not designed to be used as part of any device or equipment that may affect the human body, human
life, or assets (such as medical equipment, disaster prevention systems, security systems, combustion control
systems, infrastructure control systems, vehicle equipment, traffic systems, in-vehicle equipment, aviation equipment,
aerospace equipment, and nuclear-related equipment), excluding when specified for in-vehicle use or other uses by
ABLIC, Inc. Do not apply the products to the above listed devices and equipments.
ABLIC Inc. is not liable for any losses, damages, claims or demands caused by unauthorized or unspecified use of
the products.
9.
In general, semiconductor products may fail or malfunction with some probability. The user of the products should
therefore take responsibility to give thorough consideration to safety design including redundancy, fire spread
prevention measures, and malfunction prevention to prevent accidents causing injury or death, fires and social
damage, etc. that may ensue from the products' failure or malfunction.
The entire system in which the products are used must be sufficiently evaluated and judged whether the products are
allowed to apply for the system on customer's own responsibility.
10. The products are not designed to be radiation-proof. The necessary radiation measures should be taken in the
product design by the customer depending on the intended use.
11. The products do not affect human health under normal use. However, they contain chemical substances and heavy
metals and should therefore not be put in the mouth. The fracture surfaces of wafers and chips may be sharp. Be
careful when handling these with the bare hands to prevent injuries, etc.
12. When disposing of the products, comply with the laws and ordinances of the country or region where they are used.
13. The information described herein contains copyright information and know-how of ABLIC Inc. The information
described herein does not convey any license under any intellectual property rights or any other rights belonging to
ABLIC Inc. or a third party. Reproduction or copying of the information from this document or any part of this
document described herein for the purpose of disclosing it to a third-party is strictly prohibited without the express
permission of ABLIC Inc.
14. For more details on the information described herein or any other questions, please contact ABLIC Inc.'s sales
representative.
15. This Disclaimers have been delivered in a text using the Japanese language, which text, despite any translations into
the English language and the Chinese language, shall be controlling.
2.4-2019.07
www.ablic.com
工商网监
湘ICP备2023018690号
