S-13D1 Series
5.5 V INPUT, 150 mA,
2-CIRCUIT VOLTAGE REGULATOR
WITH DELAY FUNCTION
www.ablic.com
Rev.1.4_00
© ABLIC Inc., 2012-2018
The S-13D1 Series, developed by using the CMOS technology, is a 2-channel positive voltage regulator IC which has low
dropout voltage, high accuracy output voltage and low current consumption.
A 0.22 μF small ceramic capacitor can be used, and the S-13D1 Series includes a load current protection circuit that
prevents the output current from exceeding the current capacity of the output transistor and a thermal shutdown circuit that
prevents damage due to overheating. Also, C / F type in the S-13D1 Series has a built-in delay function that sets the
difference of rising time between channels.
Features
• Output voltage:
• Input voltage:
• Output voltage accuracy:
• Dropout voltage:
• Current consumption:
• Output current:
• Input and output capacitors:
• Ripple rejection:
• Delay function is selectable.
• Built-in overcurrent protection circuit:
• Built-in thermal shutdown circuit:
• Built-in ON / OFF circuit:
• Operation temperature range:
• Lead-free (Sn 100%), halogen-free
1.0 V to 3.6 V, selectable in 0.05 V step
1.5 V to 5.5 V
±1.0% (1.0 V to 1.45 V output product : ±15 mV)
80 mV typ. (2.8 V output product, IOUT = 100 mA)
During operation:
39 μA typ., 58 μA max. (per circuit)
During power-off:
0.1 μA typ., 1.0 μA max.
Possible to output 150 mA (VIN ≥ VOUT(S) + 1.0 V)*1 (per circuit)
A ceramic capacitor of 0.22 μF or more can be used.
70 dB typ. (3.6 V output product, f = 1.0 kHz)
Limits overcurrent of output transistor.
Prevents damage caused by heat.
Ensures long battery life
Discharge shunt function "available" / "unavailable" is selectable.
Pull-down function "available" / "unavailable" is selectable.
Ta = −40°C to +85°C
*1. Attention should be paid to the power dissipation of the package when the output current is large.
Applications
• Constant-voltage power supply for digital camera
• Constant-voltage power supply for mobile phone
• Constant-voltage power supply for portable equipment
Packages
• SOT-23-6
• HSNT-6 (1212)
1
5.5 V INPUT, 150 mA, 2-CIRCUIT VOLTAGE REGULATOR WITH DELAY FUNCTION
Rev.1.4_00
S-13D1 Series
Block Diagrams
1.
S-13D1 Series A type
*1
ON / OFF1
VOUT1
Overcurrent protection circuit
Thermal shutdown circuit
ON / OFF
circuit
+
−
Function
ON / OFF logic
Discharge shunt
function
Constant current
source pull-down
Delay function
Status
Active "H"
Unavailable
Available
Unavailable
Reference
voltage circuit
VIN
VSS
*1
Overcurrent protection circuit
+
−
ON / OFF
circuit
Reference
voltage circuit
ON / OFF2
*1.
VOUT2
Parasitic diode
Figure 1
2.
S-13D1 Series B type
*1
VOUT1
ON / OFF1
Overcurrent protection circuit
Thermal shutdown circuit
ON / OFF
circuit
+
−
*1
Reference
voltage circuit
VIN
VSS
*1
Overcurrent protection circuit
ON / OFF
circuit
+
−
*1
Reference
voltage circuit
VOUT2
ON / OFF2
*1.
Parasitic diode
Figure 2
2
Function
ON / OFF logic
Discharge shunt
function
Constant current
source pull-down
Delay function
Status
Active "H"
Available
Available
Unavailable
5.5 V INPUT, 150 mA, 2-CIRCUIT VOLTAGE REGULATOR WITH DELAY FUNCTION
Rev.1.4_00
S-13D1 Series
3.
S-13D1 Series C type
*1
ON / OFF1
VOUT1
Overcurrent protection circuit
Thermal shutdown circuit
ON / OFF
circuit
+
−
*1
Function
ON / OFF logic
Discharge shunt
function
Constant current
source pull-down
Delay function
Status
Active "H"
Available
Available
Available
Reference
voltage circuit
VIN
VSS
*1
Overcurrent protection circuit
ON / OFF
circuit
Delay circuit
+
−
*1
Reference
voltage circuit
VOUT2
ON / OFF2
*1.
Parasitic diode
Figure 3
4.
S-13D1 Series D type
*1
ON / OFF1
VOUT1
Overcurrent protection circuit
Thermal shutdown circuit
ON / OFF
circuit
+
−
Function
ON / OFF logic
Discharge shunt
function
Constant current
source pull-down
Delay function
Status
Active "H"
Unavailable
Unavailable
Unavailable
Reference
voltage circuit
VIN
VSS
*1
Overcurrent protection circuit
ON / OFF
circuit
+
−
Reference
voltage circuit
ON / OFF2
*1.
VOUT2
Parasitic diode
Figure 4
3
5.5 V INPUT, 150 mA, 2-CIRCUIT VOLTAGE REGULATOR WITH DELAY FUNCTION
Rev.1.4_00
S-13D1 Series
5.
S-13D1 Series E type
*1
VOUT1
ON / OFF1
Overcurrent protection circuit
Thermal shutdown circuit
ON / OFF
circuit
+
−
*1
Function
ON / OFF logic
Discharge shunt
function
Constant current
source pull-down
Delay function
Status
Active "H"
Available
Unavailable
Unavailable
Reference
voltage circuit
VIN
VSS
*1
Overcurrent protection circuit
ON / OFF
circuit
+
−
*1
Reference
voltage circuit
ON / OFF2
*1.
VOUT2
Parasitic diode
Figure 5
6.
S-13D1 Series F type
*1
VOUT1
ON / OFF1
Overcurrent protection circuit
Thermal shutdown circuit
ON / OFF
circuit
+
−
*1
Reference
voltage circuit
VIN
VSS
*1
Overcurrent protection circuit
ON / OFF
circuit
Delay circuit
+
−
*1
Reference
voltage circuit
ON / OFF2
*1.
VOUT2
Parasitic diode
Figure 6
4
Function
ON / OFF logic
Discharge shunt
function
Constant current
source pull-down
Delay function
Status
Active "H"
Available
Unavailable
Available
5.5 V INPUT, 150 mA, 2-CIRCUIT VOLTAGE REGULATOR WITH DELAY FUNCTION
Rev.1.4_00
S-13D1 Series
Product Name Structure
Users can select the product type, output voltage, and package type for the S-13D1 Series. Refer to "1. Product
name" regarding the contents of product name, "2. Function list of product types" regarding the product type,
"3. Packages" regarding the package drawings, "4. Product name list" regarding details of the product name.
1.
Product name
S-13D1
x
xx
xx
-
xxxx
U
3
Environmental code
U:
Lead-free (Sn 100%), halogen-free
Package abbreviation and IC packing specifications*1
M6T1: SOT-23-6, Tape
A6T2: HSNT-6 (1212), Tape
Output voltage of voltage regulator 2*2
10 to 36
(e.g., when the output voltage is 1.0 V, it is expressed as 10.)
Output voltage of voltage regulator 1*2
10 to 36
(e.g., when the output voltage is 1.0 V, it is expressed as 10.)
*3
Product type
A to F
*1.
*2.
*3.
2.
Refer to the tape drawing.
If you request the product which has 0.05 V step, contact our sales office.
Refer to "2. Function list of product types".
Function list of product types
Table 1
Product Type
A
B
C
D
E
F
3.
Constant Current Source
Pull-down
ON / OFF Logic
Discharge Shunt Function
Active "H"
Active "H"
Active "H"
Active "H"
Active "H"
Active "H"
Unavailable
Available
Available
Unavailable
Available
Available
Available
Available
Available
Unavailable
Unavailable
Unavailable
Table 2
Package Drawing Codes
Delay Function
Unavailable
Unavailable
Available
Unavailable
Unavailable
Available
Packages
Package Name
SOT-23-6
HSNT-6 (1212)
Dimension
MP006-A-P-SD
PM006-A-P-SD
Tape
MP006-A-C-SD
PM006-A-C-SD
Reel
MP006-A-R-SD
PM006-A-R-SD
Land
−
PM006-A-L-SD
5
5.5 V INPUT, 150 mA, 2-CIRCUIT VOLTAGE REGULATOR WITH DELAY FUNCTION
Rev.1.4_00
S-13D1 Series
4.
Product name list
4. 1
S-13D1 Series B type
ON / OFF logic:
Constant current source pull-down:
Active "H"
Available
Discharge shunt function:
Delay function:
Available
Unavailable
Table 3
Voltage Regulator 1
Voltage Regulator 2
SOT-23-6
HSNT-6 (1212)
Output Voltage
Output Voltage
S-13D1B1218-A6T2U3
1.2 V ± 15 mV
1.8 V ± 1.0%
S-13D1B1218-M6T1U3
S-13D1B1528-A6T2U3
1.5 V ± 1.0%
2.8 V ± 1.0%
S-13D1B1528-M6T1U3
S-13D1B1812-A6T2U3
1.8 V ± 1.0%
1.2 V ± 15 mV
S-13D1B1812-M6T1U3
S-13D1B1815-A6T2U3
1.8 V ± 1.0%
1.5 V ± 1.0%
S-13D1B1815-M6T1U3
S-13D1B1818-A6T2U3
1.8 V ± 1.0%
1.8 V ± 1.0%
S-13D1B1818-M6T1U3
S-13D1B1828-A6T2U3
1.8 V ± 1.0%
2.8 V ± 1.0%
S-13D1B1828-M6T1U3
S-13D1B1833-A6T2U3
1.8 V ± 1.0%
3.3 V ± 1.0%
S-13D1B1833-M6T1U3
S-13D1B2518-A6T2U3
2.5 V ± 1.0%
1.8 V ± 1.0%
S-13D1B2518-M6T1U3
S-13D1B2818-A6T2U3
2.8 V ± 1.0%
1.8 V ± 1.0%
S-13D1B2818-M6T1U3
S-13D1B2828-A6T2U3
2.8 V ± 1.0%
2.8 V ± 1.0%
S-13D1B2828-M6T1U3
S-13D1B2833-A6T2U3
2.8 V ± 1.0%
3.3 V ± 1.0%
S-13D1B2833-M6T1U3
S-13D1B2J2J-A6T2U3
2.85 V ± 1.0%
2.85 V ± 1.0%
S-13D1B2J2J-M6T1U3
S-13D1B3018-A6T2U3
3.0 V ± 1.0%
1.8 V ± 1.0%
S-13D1B3018-M6T1U3
S-13D1B3130-A6T2U3
3.1 V ± 1.0%
3.0 V ± 1.0%
S-13D1B3130-M6T1U3
S-13D1B3330-A6T2U3
3.3 V ± 1.0%
3.0 V ± 1.0%
S-13D1B3330-M6T1U3
S-13D1B3333-A6T2U3
3.3 V ± 1.0%
3.3 V ± 1.0%
S-13D1B3333-M6T1U3
Remark Please contact our sales office for products with specifications other than the above.
4. 2
S-13D1 Series C type
ON / OFF logic:
Constant current source pull-down:
Active "H"
Available
Discharge shunt function:
Delay function:
Available
Available
Table 4
Voltage Regulator 1
Voltage Regulator 2
SOT-23-6
HSNT-6 (1212)
Output Voltage
Output Voltage
S-13D1C1218-M6T1U3
S-13D1C1218-A6T2U3
1.2 V ± 15 mV
1.8 V ± 1.0%
S-13D1C1528-M6T1U3
S-13D1C1528-A6T2U3
1.5 V ± 1.0%
2.8 V ± 1.0%
S-13D1C1818-M6T1U3
S-13D1C1818-A6T2U3
1.8 V ± 1.0%
1.8 V ± 1.0%
S-13D1C1828-M6T1U3
S-13D1C1828-A6T2U3
1.8 V ± 1.0%
2.8 V ± 1.0%
S-13D1C1833-M6T1U3
S-13D1C1833-A6T2U3
1.8 V ± 1.0%
3.3 V ± 1.0%
S-13D1C2828-M6T1U3
S-13D1C2828-A6T2U3
2.8 V ± 1.0%
2.8 V ± 1.0%
S-13D1C2833-M6T1U3
S-13D1C2833-A6T2U3
2.8 V ± 1.0%
3.3 V ± 1.0%
S-13D1C2J2J-M6T1U3
S-13D1C2J2J-A6T2U3
2.85 V ± 1.0%
2.85 V ± 1.0%
S-13D1C3636-M6T1U3
S-13D1C3636-A6T2U3
3.6 V ± 1.0%
3.6 V ± 1.0%
Remark Please contact our sales office for products with specifications other than the above.
6
5.5 V INPUT, 150 mA, 2-CIRCUIT VOLTAGE REGULATOR WITH DELAY FUNCTION
Rev.1.4_00
S-13D1 Series
4. 3
S-13D1 Series D type
ON / OFF logic:
Constant current source pull-down:
Active "H"
Unavailable
Discharge shunt function:
Delay function:
Unavailable
Unavailable
Table 5
Voltage Regulator 1
Voltage Regulator 2
SOT-23-6
HSNT-6 (1212)
Output Voltage
Output Voltage
S-13D1D1218-M6T1U3
S-13D1D1218-A6T2U3
1.2 V ± 15 mV
1.8 V ± 1.0%
S-13D1D1528-M6T1U3
S-13D1D1528-A6T2U3
1.5 V ± 1.0%
2.8 V ± 1.0%
S-13D1D1818-M6T1U3
S-13D1D1818-A6T2U3
1.8 V ± 1.0%
1.8 V ± 1.0%
S-13D1D1828-M6T1U3
S-13D1D1828-A6T2U3
1.8 V ± 1.0%
2.8 V ± 1.0%
S-13D1D1833-M6T1U3
S-13D1D1833-A6T2U3
1.8 V ± 1.0%
3.3 V ± 1.0%
S-13D1D2828-M6T1U3
S-13D1D2828-A6T2U3
2.8 V ± 1.0%
2.8 V ± 1.0%
S-13D1D2833-M6T1U3
S-13D1D2833-A6T2U3
2.8 V ± 1.0%
3.3 V ± 1.0%
S-13D1D2J2J-M6T1U3
S-13D1D2J2J-A6T2U3
2.85 V ± 1.0%
2.85 V ± 1.0%
Remark Please contact our sales office for products with specifications other than the above.
7
5.5 V INPUT, 150 mA, 2-CIRCUIT VOLTAGE REGULATOR WITH DELAY FUNCTION
Rev.1.4_00
S-13D1 Series
Pin Configurations
1.
SOT-23-6
Table 6
Top view
6 5 4
1 2 3
Pin No.
1
2
3
4
5
6
Symbol
ON / OFF1
VIN
ON / OFF2
VOUT2
VSS
VOUT1
Pin No.
1
2
3
4
5
6
Symbol
VOUT1
VOUT2
VSS
ON / OFF2
VIN
ON / OFF1
Description
ON / OFF 1 pin
Input voltage pin
ON / OFF 2 pin
Output voltage 2 pin
GND pin
Output voltage 1 pin
Figure 7
2.
HSNT-6 (1212)
Table 7
Top view
1
2
3
6
5
4
Bottom view
6
5
4
1
2
3
Description
Output voltage 1 pin
Output voltage 2 pin
GND pin
ON / OFF 2 pin
Input voltage pin
ON / OFF 1 pin
*1
Figure 8
*1. Connect the heat sink of backside at shadowed area to the board, and set electric potential GND.
However, do not use it as the function of electrode.
8
5.5 V INPUT, 150 mA, 2-CIRCUIT VOLTAGE REGULATOR WITH DELAY FUNCTION
Rev.1.4_00
S-13D1 Series
Absolute Maximum Ratings
Table 8
Item
Symbol
VIN
VON / OFF1, VON / OFF2
VOUT1, VOUT2
IOUT1, IOUT2
Input voltage
Output voltage
Output current
SOT-23-6
PD
HSNT-6 (1212)
Operation ambient temperature
Topr
Storage temperature
Tstg
*1. When mounted on board
[Mounted board]
(1) Board size:
114.3 mm × 76.2 mm × t1.6 mm
(2) Name:
JEDEC STANDARD51-7
Power dissipation
VSS − 0.3 to VSS + 6.0
VSS − 0.3 to VSS + 6.0
VSS − 0.3 to VIN + 0.3
200
650*1
480*1
−40 to +85
−40 to +125
V
V
V
mA
mW
mW
°C
°C
The absolute maximum ratings are rated values exceeding which the product could suffer physical
damage. These values must therefore not be exceeded under any conditions.
1200
Power Dissipation (PD) [mW]
Caution
(Ta = +25°C unless otherwise specified)
Absolute Maximum Rating
Unit
1000
HSNT-6 (1212)
800
SOT-23-6
600
400
200
0
0
Figure 9
150
100
50
Ambient Temperature (Ta) [°C]
Power Dissipation of Package (When Mounted on Board)
9
5.5 V INPUT, 150 mA, 2-CIRCUIT VOLTAGE REGULATOR WITH DELAY FUNCTION
Rev.1.4_00
S-13D1 Series
Power Dissipation of HSNT-6 (1212) (Reference)
Power dissipation of package differs depending on the mounting conditions.
Consider the power dissipation characteristics under the following conditions as reference.
[Mounted board]
(1) Board size:
(2) Board material:
(3) Wiring ratio:
(4) Test conditions:
(5) Land pattern:
40 mm × 40 mm × t0.8 mm
Glass epoxy resin (four layers)
50%
When mounted on board (wind speed: 0 m/s)
Refer to the recommended land pattern (drawing code: PM006-A-L-SD)
Power Dissipation (PD) [mW]
1200
1000
800
600
400
200
0
0
Figure 10
150
100
50
Ambient Temperature (Ta) [°C]
Power Dissipation of Package (When Mounted on Board)
Table 9
Condition
HSNT-6 (1212) (When mounted on board)
10
Power Dissipation (Reference)
1000 mW
Thermal Resistance Value (θj−a)
100°C/W
5.5 V INPUT, 150 mA, 2-CIRCUIT VOLTAGE REGULATOR WITH DELAY FUNCTION
Rev.1.4_00
S-13D1 Series
Electrical Characteristics (per Circuit)
Table 10 (1 / 2)
Item
Symbol
Output voltage*1
Output current
*2
VOUT(E)
IOUT
Condition
1.0 V ≤ VOUT(S) < 1.5 V
VIN = VOUT(S) + 1.0 V,
IOUT = 30 mA
1.5 V ≤ VOUT(S) ≤ 3.6 V
VIN ≥ VOUT(S) + 1.0 V
1.0 V ≤ VOUT(S) < 1.1 V
1.1 V ≤ VOUT(S) < 1.2 V
1.2 V ≤ VOUT(S) < 1.3 V
1.3 V ≤ VOUT(S) < 1.4 V
1.4 V ≤ VOUT(S) < 1.5 V
1.5 V ≤ VOUT(S) < 1.7 V
1.7 V ≤ VOUT(S) < 2.1 V
2.1 V ≤ VOUT(S) < 2.5 V
2.5 V ≤ VOUT(S) < 2.8 V
2.8 V ≤ VOUT(S) ≤ 3.6 V
Dropout voltage*3
Vdrop
Line regulation
ΔVOUT1
VOUT(S) + 0.5 V ≤ VIN ≤ 5.5 V, IOUT = 30 mA
ΔVIN • VOUT
Load regulation
ΔVOUT2
Output voltage
temperature
coefficient*4
Current consumption
during operation
(2 circuits)
Current consumption
during operation
(per circuit)
Current consumption
during power-off
Input voltage
ON / OFF pin
input voltage "H"
ON / OFF pin
input voltage "L"
ON / OFF pin
input current "H"
ON / OFF pin
input current "L"
Ripple rejection
Short-circuit current
IOUT = 100 mA
(Ta = +25°C unless otherwise specified)
Test
Min.
Typ.
Max.
Unit
Circuit
VOUT(S)
VOUT(S)
V
V
1, 2
− 0.015 OUT(S) + 0.015
VOUT(S)
VOUT(S)
VOUT(S)
V
1, 2
× 0.99
× 1.01
*5
mA
4, 5
150
−
−
0.5
0.52
0.54
V
1, 2
−
0.42
0.44
V
1, 2
−
0.32
0.34
V
1, 2
−
0.22
0.24
V
1, 2
−
0.15
0.22
V
1, 2
−
0.14
0.21
V
1, 2
−
0.12
0.19
V
1, 2
−
0.10
0.16
V
1, 2
−
0.09
0.14
V
1, 2
−
0.08
0.13
V
1, 2
−
0.02
0.2
%/V
1, 2
VIN = VOUT(S) + 1.0 V,
1 mA ≤ IOUT ≤ 150 mA
−
15
40
mV
1, 2
ΔVOUT
ΔTa • VOUT
VIN = VOUT(S) + 1.0 V, IOUT = 30 mA,
−40°C ≤ Ta ≤ + 85°C
−
±100
−
ppm/°C
1, 2
ISS
VIN = 5.5 V, ON / OFF pin = ON,
no load
−
78
116
μA
3
ISS1
VIN = VOUT(S) + 1.0 V, ON / OFF pin = ON,
no load
−
39
58
μA
3
−
0.1
1.0
μA
3
VIN
VIN = VOUT(S) + 1.0 V, ON / OFF pin = OFF,
no load
−
1.5
−
5.5
V
−
VSH
VIN = VOUT(S) + 1.0 V, RL = 1.0 kΩ
1.0
−
−
V
6, 7
VSL
VIN = VOUT(S) + 1.0 V, RL = 1.0 kΩ
−
−
0.25
V
6, 7
0.15
0.30
0.60
μA
6, 7
−0.1
−
0.1
μA
6, 7
−0.1
−
0.1
μA
6, 7
1.0 V ≤ VOUT(S) ≤ 2.0 V
−
75
−
dB
8, 9
2.0 V < VOUT(S) ≤ 3.0 V
−
72
−
dB
8, 9
3.0 V < VOUT(S) ≤ 3.6 V
−
70
−
dB
8, 9
−
40
−
mA
4, 5
ISS2
ISH
ISL
RR
Ishort
VIN = 5.5 V,
VON / OFF = 5.5 V
A / B / C type
(with constant current
source pull-down)
D / E / F type
(without constant current
source pull-down)
VIN = 5.5 V, VON / OFF = 0 V
VIN = VOUT(S) + 1.0 V,
f = 1.0 kHz,
ΔVrip = 0.5 Vrms,
IOUT = 30 mA
VIN = VOUT(S) + 1.0 V, ON / OFF pin = ON,
VOUT = 0 V
11
5.5 V INPUT, 150 mA, 2-CIRCUIT VOLTAGE REGULATOR WITH DELAY FUNCTION
Rev.1.4_00
S-13D1 Series
Table 10 (2 / 2)
Item
Thermal shutdown
detection temperature
Thermal shutdown
release temperature
Symbol
Condition
(Ta = +25°C unless otherwise specified)
Test
Min.
Typ.
Max.
Unit
Circuit
TSD
Junction temperature
−
160
−
°C
−
TSR
Junction temperature
−
130
−
°C
−
VOUT2 pin of C / F type
(with delay function)
VIN = 5.5 V,
VOUT1 pin of C / F type
VOUT = 0.1 V
(with delay function)
B / E type
(without delay function)
VIN ≥ VOUT(S) + 1.0 V, ON / OFF1 pin and
ON / OFF2 pin are set to ON simultaneously,
RL = 1.0 kΩ, CL1, CL2 = 0.22 μF
−
12
−
Ω
4, 5
−
50
−
Ω
4, 5
50
100
−
μs
10
Discharge shunt
resistance during
power-off
(With discharge shunt
function)
RLOW
Delay time*6
(C / F type only)
tDELAY
*1. VOUT(S): Set output voltage
VOUT(E): Actual output voltage
Output voltage when fixing IOUT (= 30 mA) and inputting VOUT(S) + 1.0 V
*2. The output current at which the output voltage becomes 95% of VOUT(E) after gradually increasing the output current.
*3. Vdrop = VIN1 − (VOUT3 × 0.98)
VOUT3 is the output voltage when VIN = VOUT(S) + 1.0 V and IOUT = 100 mA.
VIN1 is the input voltage at which the output voltage becomes 98% of VOUT3 after gradually decreasing the input
voltage.
*4. A change in the temperature of the output voltage [mV/°C] is calculated using the following equation.
ΔVOUT
ΔVOUT
[mV/°C]*1 = VOUT(S) [V]*2 × ΔTa•V
[ppm/°C]*3 ÷ 1000
ΔTa
OUT
*1. Change in temperature of output voltage
*2. Set output voltage
*3. Output voltage temperature coefficient
*5. The output current can be at least this value.
Due to restrictions on the package power dissipation, this value may not be satisfied. Attention should be paid to the
power dissipation of the package when the output current is large.
This specification is guaranteed by design.
*6. Delay time shows the time period from when VOUT1 pin voltage reaches 50% of the set output voltage until VOUT2 pin
voltage reaches 50% of the set output voltage, when the ON / OFF1 pin and the ON / OFF2 pin are set to ON
simultaneously. Refer to "8. Delay function (S-13D1 Series C / F type)" in " Operation" for details.
12
5.5 V INPUT, 150 mA, 2-CIRCUIT VOLTAGE REGULATOR WITH DELAY FUNCTION
Rev.1.4_00
S-13D1 Series
Test Circuits
+
A
+
V
VIN
VOUT2
*1
VOUT1
ON / OFF2 ON / OFF1
VSS
*2
*1. Set to OFF
*2. Set to ON
Figure 11
A
Test Circuit 1
+
VIN
VOUT2
+
V
*1
VOUT1
ON / OFF2 ON / OFF1
VSS
*2
*1. Set to ON
*2. Set to OFF (set to ON in case of C / F type)
Figure 12
+
Test Circuit 2
A
VIN
VOUT2
*1
*1.
VOUT1
ON / OFF2 ON / OFF1
VSS
*1
Set to VIN or GND
Figure 13
Test Circuit 3
VIN
VOUT2
*1
A
VOUT1
ON / OFF2 ON / OFF1
VSS
*2
+
V
*1. Set to OFF
*2. Set to VIN or GND
Figure 14
Test Circuit 4
13
5.5 V INPUT, 150 mA, 2-CIRCUIT VOLTAGE REGULATOR WITH DELAY FUNCTION
Rev.1.4_00
S-13D1 Series
VIN
A
VOUT2
+
V
*1.
*2.
*1
VOUT1
ON / OFF2 ON / OFF1
VSS
*2
Set to VIN or GND
Set to OFF (set to ON in case of C / F type)
Figure 15
Test Circuit 5
VIN
VOUT2
*1
*1.
VOUT1
A
ON / OFF2 ON / OFF1
VSS
+
+
V
RL
Set to OFF
Figure 16
Test Circuit 6
VIN
RL
*1.
+
+
VOUT2
A
V
VOUT1
ON / OFF2 ON / OFF1
VSS
*1
Set to OFF (set to ON in case of C / F type)
Figure 17
Test Circuit 7
VIN
VOUT2
*1
*1.
*2.
14
ON / OFF2 ON / OFF1
VSS
Set to OFF
Set to ON
Figure 18
VOUT1
Test Circuit 8
*2
+
V
RL
5.5 V INPUT, 150 mA, 2-CIRCUIT VOLTAGE REGULATOR WITH DELAY FUNCTION
Rev.1.4_00
S-13D1 Series
VIN
VOUT2
+
V
RL
*1.
*2.
*1
VOUT1
ON / OFF2 ON / OFF1
VSS
*2
Set to ON
Set to OFF (set to ON in case of C / F type)
Figure 19
Test Circuit 9
Oscilloscope
Oscilloscope
VIN
VOUT2
VOUT1
ON / OFF2 ON / OFF1
VSS
RL
Figure 20
RL
Test Circuit 10
Standard Circuit
Input
VIN
ON / OFF1
CIN*1
Output1
VOUT1
CL1
*2
ON / OFF2 VOUT2
*2
CL2
VSS
Output2
GND
Single GND
*1.
*2.
CIN is a capacitor for stabilizing the input.
A ceramic capacitor of 0.22 μF or more can be used as CL1 and CL2.
Figure 21
Caution
The above connection diagram and constants will not guarantee successful operation. Perform
thorough evaluation using the actual application to set the constants.
15
5.5 V INPUT, 150 mA, 2-CIRCUIT VOLTAGE REGULATOR WITH DELAY FUNCTION
Rev.1.4_00
S-13D1 Series
Condition of Application
0.22 μF or more
Input capacitor (CIN):
Output capacitors (CL1, CL2): 0.22 μF or more
Caution Generally a series regulator may cause oscillation, depending on the selection of external parts.
Confirm that no oscillation occurs in the application for which the above capacitors are used.
Selection of Input and Output Capacitors (CIN, CL1, CL2)
The S-13D1 Series requires an output capacitor between the VOUT pin and the VSS pin for phase compensation.
Operation is stabilized by a ceramic capacitor with an output capacitance of 0.22 μF or more over the entire temperature
range. When using an OS capacitor, a tantalum capacitor, or an aluminum electrolytic capacitor, the capacitance must
be 0.22 μF or more.
The value of the output overshoot or undershoot transient response varies depending on the value of the output
capacitor. The required capacitance of the input capacitor differs depending on the application.
The recommended capacitance for an application is CIN ≥ 0.22 μF, CL1 ≥ 0.22 μF, CL2 ≥ 0.22 μF; however, when
selecting the output capacitor, perform sufficient evaluation, including evaluation of temperature characteristics, on the
actual device.
Explanation of Terms
1.
Low dropout voltage regulator
This voltage regulator has the low dropout voltage due to its built-in low on-resistance transistor.
2.
Output voltage (VOUT)
The accuracy of the output voltage is ensured at ±1.0% or ±15 mV*1 under the specified conditions of fixed input
voltage*2, fixed output current, and fixed temperature.
*1.
*2.
When VOUT < 1.5 V: ±15 mV, When VOUT ≥ 1.5 V: ±1.0%
Differs depending on the product.
Caution
3.
If the above conditions change, the output voltage value may vary and exceed the accuracy range
of the output voltage. Refer to " Electrical Characteristics (per Circuit)" and " Characteristics
(Typical Data) (per Circuit)" for details.
ΔVOUT1
Line regulation
ΔVIN•VOUT
Indicates the dependency of the output voltage on the input voltage. That is, the values show how much the output
voltage changes due to a change in the input voltage with the output current remaining unchanged.
4.
Load regulation (ΔVOUT2)
Indicates the dependency of the output voltage on the output current. That is, the values show how much the output
voltage changes due to a change in the output current with the input voltage remaining unchanged.
5.
Dropout voltage (Vdrop)
Indicates the difference between input voltage (VIN1) and the output voltage when; decreasing input voltage (VIN)
gradually until the output voltage has dropped out to the value of 98% of output voltage (VOUT3), which is at
VIN = VOUT(S) + 1.0 V.
Vdrop = VIN1 − (VOUT3 × 0.98)
16
5.5 V INPUT, 150 mA, 2-CIRCUIT VOLTAGE REGULATOR WITH DELAY FUNCTION
Rev.1.4_00
S-13D1 Series
6.
ΔVOUT
Output voltage temperature coefficient
ΔTa•VOUT
The shaded area in Figure 22 is the range where VOUT varies in the operation temperature range when the output
voltage temperature coefficient is ±100 ppm/°C.
Example of S-13D1B3333 typ. product
VOUT
[V]
+0.33 mV/°C
*1
VOUT(E)
−0.33mV/°C
−40
*1.
+25
+85
Ta [°C]
VOUT(E) is the value of the output voltage measured at Ta = +25°C.
Figure 22
A change in the temperature of the output voltage [mV/°C] is calculated using the following equation.
ΔVOUT
ΔVOUT
[mV/°C]*1 = VOUT(S) [V]*2 × ΔTa•V
[ppm/°C]*3 ÷ 1000
ΔTa
OUT
*1. Change in temperature of output voltage
*2. Set output voltage
*3. Output voltage temperature coefficient
17
5.5 V INPUT, 150 mA, 2-CIRCUIT VOLTAGE REGULATOR WITH DELAY FUNCTION
Rev.1.4_00
S-13D1 Series
Operation
1.
Basic operation
Figure 23 shows the block diagram of the S-13D1 Series.
The error amplifier compares the reference voltage (Vref) with feedback voltage (Vfb), which is the output voltage
resistance-divided by feedback resistors (Rs and Rf). It supplies the gate voltage necessary to maintain the constant
output voltage which is not influenced by the input voltage and temperature change, to the output transistor.
VIN
*1
Current
supply
Error
amplifier
Vref
VOUT
−
Rf
+
Vfb
Reference voltage
circuit
Rs
VSS
*1.
Parasitic diode
Figure 23
2.
Output transistor
In the S-13D1 Series, a low on-resistance P-channel MOS FET is used as the output transistor.
Be sure that VOUT does not exceed VIN + 0.3 V to prevent the voltage regulator from being damaged due to reverse
current flowing from the VOUT pin through a parasitic diode to the VIN pin, when the potential of VOUT became higher
than VIN.
18
5.5 V INPUT, 150 mA, 2-CIRCUIT VOLTAGE REGULATOR WITH DELAY FUNCTION
Rev.1.4_00
S-13D1 Series
3.
ON / OFF pin
This pin starts and stops the regulator.
When the ON / OFF pin is set to OFF level, the entire internal circuit stops operating, and the built-in P-channel MOS
FET output transistor between the VIN pin and the VOUT pin is turned off, reducing current consumption significantly.
Note that the current consumption increases when a voltage of 0.3 V to VIN − 0.3 V is applied to the ON / OFF pin.
The ON / OFF pin is configured as shown in Figure 24 and Figure 25.
3. 1 S-13D1 Series A / B / C type
The ON / OFF pin is internally pulled down to the VSS pin in the floating status, so the VOUT pin is set to the VSS
level.
3. 2 S-13D1 Series D / E / F type
The ON / OFF pin is not internally pulled down to the VSS pin, so do not use it in the floating status. When not using
the ON / OFF pin, connect the pin to the VIN pin.
Product Type
A/B/C/D/E/F
A/B/C/D/E/F
ON / OFF Pin
"H": ON
"L": OFF
Table 11
Internal Circuit
Operate
Stop
VOUT Pin Voltage
Set value
VSS level
Current Consumption
ISS1*1
ISS2
*1. Note that the IC's current consumption increases as much as current flows into the constant current of 0.3 μA
typ. when the ON / OFF pin is connected to VIN pin and the S-13D1 Series A / B / C type is operating (refer to
Figure 24).
VIN
ON / OFF
VIN
ON / OFF
VSS
Figure 24
S-13D1 Series A / B / C Type
VSS
Figure 25
S-13D1 Series D / E / F Type
19
5.5 V INPUT, 150 mA, 2-CIRCUIT VOLTAGE REGULATOR WITH DELAY FUNCTION
Rev.1.4_00
S-13D1 Series
4.
Discharge shunt function (S-13D1 Series B / C / E / F type)
The S-13D1 Series B / C / E / F type has a built-in discharge shunt circuit to discharge the output capacitance.
The output capacitance is discharged as follows so that the VOUT pin reaches the VSS level.
(1) The ON / OFF pin is set to OFF level.
(2) The output transistor is turned off.
(3) The discharge shunt circuit is turned on.
(4) The output capacitor discharges.
Since the S-13D1 Series A / D type does not have a discharge shunt circuit, the VOUT pin is set to the VSS level
through several hundred kΩ internal divided resistors between the VOUT pin and the VSS pin. The S-13D1 Series B /
C / E / F type allows the VOUT pin to reach the VSS level rapidly due to the discharge shunt circuit.
S-13D1 Series
Output transistor: OFF
*1
VOUT
VIN
Discharge shunt circuit
: ON
*1
ON / OFF
ON / OFF circuit
Output
capacitor
(CL)
ON / OFF pin: OFF
Current flow
GND
VSS
*1. Parasitic diode
Figure 26
20
5.5 V INPUT, 150 mA, 2-CIRCUIT VOLTAGE REGULATOR WITH DELAY FUNCTION
Rev.1.4_00
S-13D1 Series
Moreover, C / F type in the S-13D1 Series, if the ON / OFF1 pin and the ON / OFF2 pin are set to OFF
simultaneously, the discharge shunt on-resistance connected with the VOUT2 pin is reduced in order to make it
easy for VOUT2 pin voltage to fall previously.
Table 12
Product Type
VOUT2 pin of C / F type
VOUT1 pin of C / F type, and B / E type
Discharge Shunt ON-resistance (VIN = 5.5 V, VOUT = 0.1 V)
12 Ω
50 Ω
ON / OFF1, ON / OFF2
VOUT1
VOUT2
Figure 27
50 Ω
Discharge
12 Ω
Discharge
Discharge Shunt Function of S-13D1 Series C / F Type
21
5.5 V INPUT, 150 mA, 2-CIRCUIT VOLTAGE REGULATOR WITH DELAY FUNCTION
Rev.1.4_00
S-13D1 Series
5.
Constant current source pull-down (S-13D1 Series A / B / C type)
The ON / OFF pin is internally pulled down to the VSS pin in the floating status, so the VOUT pin is set to the VSS level.
Note that the IC's current consumption increases as much as current flows into the constant current of 0.3 μA typ.
when the ON / OFF pin is connected to the VIN pin and the S-13D1 Series A / B / C type is operating.
6.
Overcurrent protection circuit
The S-13D1 Series includes an overcurrent protection circuit which has the characteristics shown in "1. Output
voltage vs. Output current (When load current increases) (Ta = +25°C)" in " Characteristics (Typical Data) (per
Circuit)", in order to protect the output transistor against an excessive output current and short circuiting between the
VOUT pin and the VSS pin. The current when the output pin is short-circuited (Ishort) is internally set at approx. 40 mA
typ., and the normal value is restored for the output voltage, if releasing a short circuit once.
Caution This overcurrent protection circuit does not work as for thermal protection. If this IC long keeps
short circuiting inside, pay attention to the conditions of input voltage and load current so that,
under the usage conditions including short circuit, the loss of the IC will not exceed power
dissipation of the package.
7.
Thermal shutdown circuit
The S-13D1 Series has a thermal shutdown circuit to protect the device from damage due to overheat. When the
junction temperature rises to 160°C typ., the thermal shutdown circuit operates to stop regulating. When the junction
temperature drops to 130°C typ., the thermal shutdown circuit is released to restart regulating.
Due to self-heating of the S-13D1 Series, if the thermal shutdown circuit starts operating, it stops regulating so that
the output voltage drops. When regulation stops, the S-13D1 Series does not itself generate heat and the IC's
temperature drops. When the temperature drops, the thermal shutdown circuit is released to restart regulating, thus
the S-13D1 Series generates heat again. Repeating this procedure makes the waveform of the output voltage into a
pulse-like form. Stop or restart of regulation continues unless decreasing either or both of the input voltage and the
output current in order to reduce the internal power consumption, or decreasing the ambient temperature.
Table 13
Thermal Shutdown Circuit
Operate: 160°C typ.*1
Release: 130°C typ.*1
*1. Junction temperature
22
VOUT Pin Voltage
VSS level
Set value
5.5 V INPUT, 150 mA, 2-CIRCUIT VOLTAGE REGULATOR WITH DELAY FUNCTION
Rev.1.4_00
S-13D1 Series
8.
Delay function (S-13D1 Series C / F type)
C / F type in the S-13D1 Series has a built-in delay function that sets the difference of rising time between
channels. If the ON / OFF1 pin and the ON / OFF2 pin are set to ON simultaneously, VOUT2 pin voltage rises after
the delay time (tDELAY = 100 μs typ.).
ON / OFF1, ON / OFF2
50% of the set output voltage
tDELAY =
100 μs typ.
VOUT1
50% of the set output voltage
VOUT2
Figure 28
8. 1
In case ON / OFF2 pin is set to ON later
The VOUT1 pin voltage rises simultaneously when the ON / OFF1 pin is set to ON. After the ON / OFF2 pin is
set to ON, VOUT2 pin voltage rises in 100 μs typ.
ON / OFF1
ON / OFF2
VOUT1
100 μs typ.
VOUT2
Figure 29
8. 2
In case ON / OFF2 pin is set to ON previously
VOUT2 pin voltage does no rise even if the ON / OFF2 pin is set to ON. VOUT1 pin voltage rises if the ON /
OFF1 pin is set to ON. After VOUT1 pin voltage rises, VOUT2 pin voltage rises in 100 μs typ.
Current comsumption < 10 μA
ON / OFF1
ON / OFF2
VOUT1
100 μs typ.
VOUT2
Figure 30
Caution
Note that the current consumption of less than 10 μA flows during the time period from when
the ON / OFF2 pin is set to ON until the ON / OFF1 pin is set to ON.
23
5.5 V INPUT, 150 mA, 2-CIRCUIT VOLTAGE REGULATOR WITH DELAY FUNCTION
Rev.1.4_00
S-13D1 Series
Precautions
• Wiring patterns for the VIN pin, the VOUT pin and GND should be designed so that the impedance is low. When
mounting the output capacitors between the VOUT pin and the VSS pin (CL1, CL2) and a capacitor for stabilizing the
input between the VIN pin and the VSS pin (CIN), the distance from the capacitors to these pins should be as short as
possible.
• Note that generally the output voltage may increase when a series regulator is used at low load current (1.0 mA or
less).
• Note that generally the output voltage may increase due to the leakage current from an output driver when a series
regulator is used at high temperature.
• Note that the output voltage may increase due to the leakage current from an output driver even if the ON / OFF pin is
at OFF level when a series regulator is used at a high temperature.
• Generally a series regulator may cause oscillation, depending on the selection of external parts. The following
conditions are recommended for the S-13D1 Series. However, be sure to perform sufficient evaluation under the
actual usage conditions for selection, including evaluation of temperature characteristics. Refer to "6. Example of
equivalent series resistance vs. Output current characteristics (Ta = +25°C)" in " Reference Data (per Circuit)"
for the equivalent series resistance (RESR) of the output capacitors.
Input capacitor (CIN):
Output capacitors (CL1, CL2):
0.22 μF or more
0.22 μF or more
• The voltage regulator may oscillate when the impedance of the power supply is high and the input capacitance is small
or an input capacitor is not connected.
• If the output capacitance is small, power supply's fluctuation and the characteristics of load fluctuation become worse.
Sufficiently evaluate the output voltage's fluctuation with the actual device.
• Overshoot may occur in the output voltage momentarily if the voltage is rapidly raised at power-on or when the power
supply fluctuates. Sufficiently evaluate the output voltage at power-on with the actual device.
• The application conditions for the input voltage, the output voltage, and the load current should not exceed the
package power dissipation.
• Do not apply an electrostatic discharge to this IC that exceeds the performance ratings of the built-in electrostatic
protection circuit.
• In determining the output current, attention should be paid to the output current value specified in Table 10 in
" Electrical Characteristics (per Circuit)" and footnote *5 of the table.
• ABLIC Inc. claims no responsibility for any disputes arising out of or in connection with any infringement by products
including this IC of patents owned by a third party.
24
5.5 V INPUT, 150 mA, 2-CIRCUIT VOLTAGE REGULATOR WITH DELAY FUNCTION
Rev.1.4_00
S-13D1 Series
Characteristics (Typical Data) (per Circuit)
Output voltage vs. Output current (When load current increases) (Ta = +25°C)
1. 1
VOUT = 1.0 V
1. 2
1.2
1.0
VOUT [V]
0.8
2.5
VIN = 2.0 V
VIN = 3.0 V
VIN = 5.5 V
VIN = 1.3 V
0.6
0.4
0.2
1.0
100
200
300
IOUT [mA]
400
500
0
100
200
300
IOUT [mA]
400
500
VOUT = 3.6 V
4.0
3.5
3.0
2.5
2.0
1.5
1.0
0.5
0
VOUT [V]
1.5
0
0
VIN = 4.6 V
VIN = 5.5 V
VIN = 3.9 V
VIN = 4.1 V
0
100
200
300
IOUT [mA]
400
Remark
In determining the output current, attention should
be paid to the following.
1. The minimum output current value and
footnote *5 in Table 10 in " Electrical
Characteristics (per Circuit)"
2. The package power dissipation
500
Output voltage vs. Input voltage (Ta = +25°C)
VOUT [V]
2. 1
VOUT = 1.0 V
2. 2
3.0
1.0
2.5
0.8
IOUT = 1 mA
IOUT = 30 mA
IOUT = 50 mA
IOUT = 100 mA
0.6
0.4
0.2
IOUT = 1 mA
IOUT = 30 mA
IOUT = 50 mA
IOUT = 100 mA
1.5
1.0
0
0
VOUT [V]
2.0
0.5
0
2. 3
VOUT = 2.5 V
1.2
VOUT [V]
2.
VIN = 3.5 V
VIN = 4.5 V
VIN = 5.5 V
VIN = 2.8 V
VIN = 3.0 V
2.0
0.5
0
1. 3
VOUT = 2.5 V
3.0
VIN = 1.5 V
VOUT [V]
1.
1
2
3
VIN [V]
4
5
6
0
1
2
3
VIN [V]
4
5
6
VOUT = 3.6 V
4.0
3.5
3.0
2.5
2.0
1.5
1.0
0.5
0
IOUT = 1 mA
IOUT = 30 mA
IOUT = 50 mA
IOUT = 100 mA
0
1
2
3
VIN [V]
4
5
6
25
5.5 V INPUT, 150 mA, 2-CIRCUIT VOLTAGE REGULATOR WITH DELAY FUNCTION
Rev.1.4_00
S-13D1 Series
Dropout voltage vs. Output current
Vdrop [V]
3. 1
VOUT = 1.0 V
0.40
0.35
0.30
0.25
0.20
0.15
0.10
0.05
0
Ta = +85°C
Ta = +25°C
Ta = −40°C
0
25
50
100
75
IOUT [mA]
125
150
125
150
VOUT = 3.6 V
Vdrop [V]
Ta = +85°C
Ta = +25°C
Ta = −40°C
0.10
0.05
0
0
Vdrop [V]
0.10
0.05
0.15
25
50
100
75
IOUT [mA]
Dropout voltage vs. Set output voltage (Ta = +25°C)
0.50
0.45
0.40
0.35
0.30
0.25
0.20
0.15
0.10
0.05
0
IOUT = 150 mA
IOUT = 100 mA
IOUT = 50 mA
IOUT = 30 mA
IOUT = 10 mA IOUT = 1 mA
1.0
26
Ta = +85°C
Ta = +25°C
Ta = −40°C
0.15
0.20
4.
VOUT = 2.5 V
0.20
0
3. 3
3. 2
Vdrop [V]
3.
1.5
2.0
2.5
3.0
VOUT(S) [V]
3.5
4.0
0
25
50
100
75
IOUT [mA]
125
150
5.5 V INPUT, 150 mA, 2-CIRCUIT VOLTAGE REGULATOR WITH DELAY FUNCTION
Rev.1.4_00
S-13D1 Series
Output voltage vs. Ambient temperature
5. 1
VOUT = 1.0 V
VOUT [V]
1.05
1.04
1.03
1.02
1.01
1.00
0.99
0.98
0.97
0.96
0.95
−40 −25
5. 3
0
25
Ta [°C]
50
75 85
0
25
Ta [°C]
50
75 85
VOUT = 2.5 V
2.55
2.54
2.53
2.52
2.51
2.50
2.49
2.48
2.47
2.46
2.45
−40 −25
0
25
Ta [°C]
75 85
50
VOUT = 3.6 V
VOUT [V]
3.65
3.64
3.63
3.62
3.61
3.60
3.59
3.58
3.57
3.56
3.55
−40 −25
Current consumption vs. Input voltage
ISS1 [μA]
6. 1
VOUT = 1.0 V
6. 2
60
50
50
40
Ta = −40°C
Ta = +25°C
Ta = +85°C
30
20
10
40
Ta = −40°C
Ta = +25°C
Ta = +85°C
30
20
10
0
0
0
6. 3
VOUT = 2.5 V
60
ISS1 [μA]
6.
5. 2
VOUT [V]
5.
1
2
3
VIN [V]
4
5
6
4
5
6
0
1
2
3
VIN [V]
4
5
6
VOUT = 3.6 V
60
ISS1 [μA]
50
Ta = −40°C
Ta = +25°C
Ta = +85°C
40
30
20
10
0
0
1
2
3
VIN [V]
27
5.5 V INPUT, 150 mA, 2-CIRCUIT VOLTAGE REGULATOR WITH DELAY FUNCTION
Rev.1.4_00
S-13D1 Series
7.
Ripple rejection (Ta = +25°C)
7. 1
VOUT = 1.0 V
7. 2
VOUT = 2.5 V
120
100
80
60
IOUT = 1 mA
IOUT = 30 mA
IOUT = 100 mA
40
20
0
10
7. 3
100
1k
10k
100k
Frequency [Hz]
VIN = 3.5 V, CLn = 0.22 μF
Ripple Rejection [dB]
Ripple Rejection [dB]
VIN = 2.0 V, CLn = 0.22 μF
120
100
80
60
20
0
1M
VOUT = 3.6 V
Ripple Rejection [dB]
VIN = 4.6 V, CLn = 0.22 μF
120
100
80
60
IOUT = 1 mA
IOUT = 30 mA
IOUT = 100 mA
40
20
0
10
Remark
28
100
1k
10k
100k
Frequency [Hz]
IOUT = 1 mA
IOUT = 30 mA
IOUT = 100 mA
40
1M
CLn: Output capacitor set to the VOUTn pin externally (n = 1, 2)
10
100
1k
10k
100k
Frequency [Hz]
1M
5.5 V INPUT, 150 mA, 2-CIRCUIT VOLTAGE REGULATOR WITH DELAY FUNCTION
Rev.1.4_00
S-13D1 Series
Reference Data (per Circuit)
Transient response characteristics when input (Ta = +25°C)
1. 1
VOUT = 1.0 V
1. 2
VOUT = 2.5 V
IOUT = 30 mA, CLn = 0.22 μF,
VIN = 3.5 V ↔ 4.5 V, tr = tf = 5.0 μs
VOUT
−40 −20 0
1. 3
6.0
5.5
5.0
4.5
4.0
3.5
3.0
2.5
2.0
1.5
1.0
VOUT [V]
VIN
4.0
3.5
3.0
2.5
2.0
1.5
1.0
0.5
0.0
−0.5
−1.0
VIN [V]
1.14
1.12
1.10
1.08
1.06
1.04
1.02
1.00
0.98
0.96
0.94
VIN [V]
VOUT [V]
IOUT = 30 mA, CIN = CLn = 0.22 μF,
VIN = 2.0 V ↔ 3.0 V, tr = tf = 5.0 μs
2.65
2.63
2.61
2.59
2.57
2.55
2.53
2.51
2.49
2.47
2.45
VIN
VOUT
−40 −20 0
20 40 60 80 100 120 140
t [μs]
6.0
5.5
5.0
4.5
4.0
3.5
3.0
2.5
2.0
1.5
1.0
20 40 60 80 100 120 140
t [μs]
VOUT = 3.6 V
VOUT [V]
IOUT = 30 mA, CLn = 0.22 μF,
VIN = 4.6 V ↔ 5.5 V, tr = tf = 5.0 μs
3.75
3.73
3.71
3.69
3.67
3.65
3.63
3.61
3.59
3.57
3.55
VIN
VOUT
−40 −20 0
Remark
20 40 60 80 100 120 140
t [μs]
CLn: Output capacitor set to the VOUTn pin externally (n = 1, 2)
29
VIN [V]
1.
5.5 V INPUT, 150 mA, 2-CIRCUIT VOLTAGE REGULATOR WITH DELAY FUNCTION
Rev.1.4_00
S-13D1 Series
Transient response characteristics of load (Ta = +25°C)
2. 1
VOUT = 1.0 V
2. 2
VOUT = 2.5 V
VOUT
−40 −20 0
2. 3
140
120
100
80
60
40
20
0
−20
−40
−60
VOUT [V]
IOUT
140
120
100
80
60
40
20
0
−20
−40
−60
IOUT [mA]
VOUT [V]
1.35
1.30
1.25
1.20
1.15
1.10
1.05
1.00
0.95
0.90
0.85
VIN = 3.5 V, CIN = CLn = 0.22 μF,
IOUT = 50 mA ↔ 100 mA
IOUT [mA]
VIN = 2.0 V, CIN = CLn = 0.22 μF,
IOUT = 50 mA ↔ 100 mA
2.90
2.85
2.80
2.75
2.70
2.65
2.60
2.55
2.50
2.45
2.40
IOUT
VOUT
−40 −20 0
20 40 60 80 100 120 140
t [μs]
VOUT = 3.6 V
VOUT [V]
VIN = 4.6 V, CIN = CLn = 0.22 μF,
IOUT = 50 mA ↔ 100 mA
4.00
3.95
3.90
3.85
3.80
3.75
3.70
3.65
3.60
3.55
3.50
IOUT
VOUT
−40 −20 0
Remark
30
140
120
100
80
60
40
20
0
−20
−40
−60
20 40 60 80 100 120 140
t [μs]
CLn: Output capacitor set to the VOUTn pin externally (n = 1, 2)
20 40 60 80 100 120 140
t [μs]
IOUT [mA]
2.
5.5 V INPUT, 150 mA, 2-CIRCUIT VOLTAGE REGULATOR WITH DELAY FUNCTION
Rev.1.4_00
S-13D1 Series
Transient response characteristics of load’s mutual interference (Ta = +25°C)
VOUT1 = VOUT2 = 1.0 V
VOUT1 [V]
VOUT2 [V]
VOUT1 = VOUT2 = 2.5 V
VIN = 3.5 V, CIN = CLn = 0.22 μF, IOUT2 = 50 mA ↔ 100 mA
120
100
IOUT2
80
60
40
2.60
2.55
VOUT2
2.50
2.45
2.40
2.60
2.55
2.50
VOUT1
2.45
2.40
2.35
−40 −20 0 20 40 60 80 100 120 140
t [μs]
VOUT2 [V]
VOUT2 [V]
VOUT1 [V]
VOUT1 [V]
IOUT1 [mA]
VIN = 3.5 V, CIN = CLn = 0.22 μF, IOUT1 = 50 mA ↔ 100 mA
120
100
IOUT1
80
60
40
2.60
2.55
VOUT2
2.50
2.45
2.40
2.60
2.55
2.50
VOUT1
2.45
2.40
2.35
−40 −20 0 20 40 60 80 100 120 140
t [μs]
3. 3 VOUT1 = VOUT2 = 3.6 V
IOUT2 [mA]
3. 2
VIN = 2.0 V, CIN = CLn = 0.22 μF, IOUT2 = 50 mA ↔ 100 mA
120
100
IOUT2
80
60
40
1.10
1.05
VOUT2
1.00
0.95
0.90
1.10
1.05
1.00
VOUT1
0.95
0.90
0.85
−40 −20 0 20 40 60 80 100 120 140
t [μs]
IOUT2 [mA]
IOUT1 [mA]
VIN = 2.0 V, CIN = CLn = 0.22 μF, IOUT1 = 50 mA ↔ 100 mA
120
100
IOUT1
80
60
40
1.10
1.05
VOUT2
1.00
0.95
0.90
1.10
1.05
1.00
VOUT1
0.95
0.90
0.85
−40 −20 0 20 40 60 80 100 120 140
t [μs]
VOUT2 [V]
3. 1
VOUT1 [V]
3.
IOUT1 [mA]
IOUT2 [mA]
VOUT2 [V]
VOUT2 [V]
VOUT1 [V]
Remark
VIN = 4.6 V, CIN = CLn = 0.22 μF, IOUT2 = 50 mA ↔ 100 mA
120
100
IOUT2
80
60
40
3.70
3.65
VOUT2
3.60
3.55
3.50
3.70
3.65
3.60
VOUT1
3.55
3.50
3.45
−40 −20 0 20 40 60 80 100 120 140
t [μs]
VOUT1 [V]
VIN = 4.6 V, CIN = CLn = 0.22 μF, IOUT1 = 50 mA ↔ 100 mA
120
100
IOUT1
80
60
40
3.70
3.65
VOUT2
3.60
3.55
3.50
3.70
3.65
3.60
VOUT1
3.55
3.50
3.45
−40 −20 0 20 40 60 80 100 120 140
t [μs]
CLn: Output capacitor set to the VOUTn pin externally (n = 1, 2)
31
5.5 V INPUT, 150 mA, 2-CIRCUIT VOLTAGE REGULATOR WITH DELAY FUNCTION
Rev.1.4_00
S-13D1 Series
Transient response characteristics of ON / OFF pin (Ta = +25°C)
4. 1
S-13D1 Series A / B / D / E type (without delay function)
4. 1. 1
VOUT = 1.0 V
4. 1. 2
VIN = 3.5 V, CIN = CLn = 0.22 μF, IOUT = 30 mA,
VON / OFF = 0 V → 3.5 V, tr = 1.0 μs
6
6
2.0
4
5
VON / OFF
1.6
VOUT
1.2
2
0
1
−4
0
−40
80 120 160 200 240
t [μs]
VOUT = 3.6 V
VIN = 4.6 V, CIN = CLn = 0.22 μF, IOUT = 30 mA,
VON / OFF = 0 V → 4.6 V, tr = 1.0 μs
7.2
6
VON / OFF
4.8
2
3.6
VOUT
2.4
0
−2
−4
1.2
−6
0
−40
Remark
32
4
VON / OFF [V]
VOUT [V]
6.0
0
40
0
−6
0
4. 1. 3
2
VOUT
3
−4
0.4
40
4
4
−2
−2
0
6
VON / OFF
2
0.8
−40
VOUT [V]
2.4
VON / OFF [V]
VOUT [V]
VIN = 2.0 V, CIN = CLn = 0.22 μF, IOUT = 30 mA,
VON / OFF = 0 V → 2.0 V, tr = 1.0 μs
VOUT = 2.5 V
80 120 160 200 240
t [μs]
CLn: Output capacitor set to the VOUTn pin externally (n = 1, 2)
−6
0
40
80 120 160 200 240
t [μs]
VON / OFF [V]
4.
5.5 V INPUT, 150 mA, 2-CIRCUIT VOLTAGE REGULATOR WITH DELAY FUNCTION
Rev.1.4_00
S-13D1 Series
S-13D1 Series C / F type (with delay function, when VON / OFF1 and VON / OFF2 are raised simultaneously)
VOUT1 = VOUT2 = 1.0 V
(2) VOUT2
(1) VOUT1
VIN = 2.0 V, CIN = CL2 = 0.22 μF, IOUT = 30 mA,
VON / OFF2 = 0 V → 2.0 V, tr = 1.0 μs
2.4
4
2.0
VON / OFF1
1.6
VOUT1
1.2
2
0
0.8
−2
0.4
−4
−6
0
−40
4. 2. 2
0
40
1.2
−2
0.4
−4
−6
0
−40
0
40
80 120 160 200 240
t [μs]
4
6
6
4
5
2
VOUT1
3
0
2
−2
1
−4
VOUT2 [V]
VON / OFF1
VIN = 3.5 V, CIN = CL2 = 0.22 μF, IOUT = 30 mA,
VON / OFF2 = 0 V → 3.5 V, tr = 1.0 μs
VON / OFF1 [V]
VOUT1 [V]
0
(2) VOUT2
5
−6
0
0
40
6
VON / OFF2
4
4
2
3
VOUT2
0
2
−2
1
−4
−6
0
−40
80 120 160 200 240
t [μs]
0
40
80 120 160 200 240
t [μs]
VOUT1 = VOUT2 = 3.6 V
(2) VOUT2
(1) VOUT1
VIN = 4.6 V, CIN = CL1 = 0.22 μF, IOUT = 30 mA,
VON / OFF1 = 0 V → 4.6 V, tr = 1.0 μs
VIN = 4.6 V, CIN = CL2 = 0.22 μF, IOUT = 30 mA,
VON / OFF2 = 0 V → 4.6 V, tr = 1.0 μs
6
7.2
6.0
4
6.0
VON / OFF1
4.8
2
3.6
VOUT1
2.4
0
−2
−4
1.2
−6
0
0
40
80 120 160 200 240
t [μs]
VOUT2 [V]
7.2
VON / OFF1 [V]
VOUT1 [V]
2
VOUT1 = VOUT2 = 2.5 V
6
−40
VOUT2
4
0.8
VIN = 3.5 V, CIN = CL1 = 0.22 μF, IOUT = 30 mA,
VON / OFF1 = 0 V → 3.5 V, tr = 1.0 μs
4. 2. 3
VON / OFF2
1.6
80 120 160 200 240
t [μs]
(1) VOUT1
−40
6
VON / OFF2 [V]
6
2.0
VOUT2 [V]
2.4
VON / OFF1 [V]
VOUT1 [V]
VIN = 2.0 V, CIN = CL1 = 0.22 μF, IOUT = 30 mA,
VON / OFF1 = 0 V → 2.0 V, tr = 1.0 μs
VON / OFF2 [V]
4. 2. 1
6
VON / OFF2
4.8
4
2
3.6
VOUT2
2.4
0
−2
−4
1.2
−6
0
−40
VON / OFF2 [V]
4. 2
0
40
80 120 160 200 240
t [μs]
33
5.5 V INPUT, 150 mA, 2-CIRCUIT VOLTAGE REGULATOR WITH DELAY FUNCTION
Rev.1.4_00
S-13D1 Series
5.
Output capacitance vs. Characteristics of discharge time (Ta = +25°C)
5. 1
S-13D1 Series B / E type (with discharge shunt function, without delay funciton)
5. 1. 1
VOUT
VIN = VOUT + 1.0 V, IOUT = no load,
VON / OFF = VOUT + 1.0 V → VSS, tf = 1.0 μs
tDSC [ms]
4.0
3.5
3.0
2.5
2.0
1.5
1.0
0.5
0
VOUT(S) = 1.0 V
VOUT(S) = 2.5 V
VOUT(S) = 3.6 V
0
2
4
6
8
CLn [μF]
10
12
Figure 31
5. 2
S-13D1 Series C / F type (with discharge shunt function, with delay funciton)
5. 2. 1
VOUT1
5. 2. 2
4.0
3.5
3.0
2.5
2.0
1.5
1.0
0.5
0
VOUT(S) = 1.0 V
VOUT(S) = 2.5 V
VOUT(S) = 3.6 V
0
2
4
6
8
CL1 [μF]
tDSC [ms]
tDSC [ms]
VIN = VOUT1 + 1.0 V, IOUT1 = no load,
VON / OFF1 = VOUT1 + 1.0 V → VSS, tf = 1.0 μs
10
12
VIN = VOUT2 + 1.0 V, IOUT2 = no load,
VON / OFF2 = VOUT2 + 1.0 V → VSS, tf = 1.0 μs
4.0
3.5
3.0
2.5
2.0
VOUT(S) = 1.0 V
1.5
VOUT(S) = 2.5 V
1.0
VOUT(S) = 3.6 V
0.5
0
0
2
4
6
8
10
12
CL2 [μF]
Figure 32
Figure 33
1 μs
VON / OFF
VSS
tDSC
VOUT
VOUT × 10%
VIN = VOUT + 1.0 V
VON / OFF = VOUT + 1.0 V → VSS
Figure 34
Remark
34
VOUT2
Measurement Condition of Discharge Time
CLn: Output capacitor set to the VOUTn pin externally (n = 1, 2)
5.5 V INPUT, 150 mA, 2-CIRCUIT VOLTAGE REGULATOR WITH DELAY FUNCTION
Rev.1.4_00
S-13D1 Series
Example of equivalent series resistance vs. Output current characteristics (Ta = +25°C)
6.
CIN = CLn = 0.22 μF
100
RESR [Ω]
VIN
CIN
Stable
VOUT
S-13D1 Series
CLn
ON / OFF
0
0.1
VSS
200
*1
RESR
IOUT [mA]
*1.
CLn: TDK Corporation C2012X7R1H224K (0.22 μF)
Figure 35
Remark
Figure 36
CLn: Output capacitor set to the VOUTn pin externally (n = 1, 2)
35
5.5 V INPUT, 150 mA, 2-CIRCUIT VOLTAGE REGULATOR WITH DELAY FUNCTION
Rev.1.4_00
S-13D1 Series
Marking Specifications
1.
SOT-23-6
Top view
6
5
4
(1) to (3):
(4):
Product code (Refer to Product name vs. Product code)
Lot number
(1) (2) (3) (4)
1
2
3
Product name vs. Product code
1. 1
S-13D1 Series B type
Product Name
S-13D1B1218-M6T1U3
S-13D1B1528-M6T1U3
S-13D1B1812-M6T1U3
S-13D1B1815-M6T1U3
S-13D1B1818-M6T1U3
S-13D1B1828-M6T1U3
S-13D1B1833-M6T1U3
S-13D1B2518-M6T1U3
S-13D1B2818-M6T1U3
S-13D1B2828-M6T1U3
S-13D1B2833-M6T1U3
S-13D1B2J2J-M6T1U3
S-13D1B3018-M6T1U3
S-13D1B3130-M6T1U3
S-13D1B3330-M6T1U3
S-13D1B3333-M6T1U3
1. 3
S-13D1 Series D type
Product Name
S-13D1D1218-M6T1U3
S-13D1D1528-M6T1U3
S-13D1D1818-M6T1U3
S-13D1D1828-M6T1U3
S-13D1D1833-M6T1U3
S-13D1D2828-M6T1U3
S-13D1D2833-M6T1U3
S-13D1D2J2J-M6T1U3
36
1. 2
Product Code
(1)
(2)
(3)
1
5
K
1
6
B
1
5
G
1
5
H
1
5
L
1
5
N
1
6
A
1
5
J
1
5
F
1
5
O
1
5
P
1
5
Q
1
5
A
1
5
D
1
5
C
1
5
B
(1)
1
1
1
1
1
1
1
1
Product Code
(2)
(3)
7
A
7
H
7
B
7
C
7
G
7
D
7
E
7
F
S-13D1 Series C type
Product Name
S-13D1C1218-M6T1U3
S-13D1C1528-M6T1U3
S-13D1C1818-M6T1U3
S-13D1C1828-M6T1U3
S-13D1C1833-M6T1U3
S-13D1C2828-M6T1U3
S-13D1C2833-M6T1U3
S-13D1C2J2J-M6T1U3
S-13D1C3636-M6T1U3
(1)
1
1
1
1
1
1
1
1
1
Product Code
(2)
(3)
5
U
5
3
5
V
5
X
5
2
5
Y
5
Z
5
1
5
S
5.5 V INPUT, 150 mA, 2-CIRCUIT VOLTAGE REGULATOR WITH DELAY FUNCTION
Rev.1.4_00
S-13D1 Series
2.
HSNT-6 (1212)
Top view
6
5
4
(1) to (3):
(4), (5):
Product code (Refer to Product name vs. Product code)
Lot number
(1) (2) (3)
(4) (5)
1
2
3
Product name vs. Product code
2. 1
S-13D1 Series B type
Product Name
S-13D1B1218-A6T2U3
S-13D1B1528-A6T2U3
S-13D1B1812-A6T2U3
S-13D1B1815-A6T2U3
S-13D1B1818-A6T2U3
S-13D1B1828-A6T2U3
S-13D1B1833-A6T2U3
S-13D1B2518-A6T2U3
S-13D1B2818-A6T2U3
S-13D1B2828-A6T2U3
S-13D1B2833-A6T2U3
S-13D1B2J2J-A6T2U3
S-13D1B3018-A6T2U3
S-13D1B3130-A6T2U3
S-13D1B3330-A6T2U3
S-13D1B3333-A6T2U3
2. 3
2. 2
(1)
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Product Code
(2)
(3)
5
K
6
B
5
G
5
H
5
L
5
N
6
A
5
J
5
F
5
O
5
P
5
Q
5
A
5
D
5
C
5
B
S-13D1 Series C type
Product Name
S-13D1C1218-A6T2U3
S-13D1C1528-A6T2U3
S-13D1C1818-A6T2U3
S-13D1C1828-A6T2U3
S-13D1C1833-A6T2U3
S-13D1C2828-A6T2U3
S-13D1C2833-A6T2U3
S-13D1C2J2J-A6T2U3
S-13D1C3636-A6T2U3
(1)
1
1
1
1
1
1
1
1
1
Product Code
(2)
(3)
5
U
5
3
5
V
5
X
5
2
5
Y
5
Z
5
1
5
S
S-13D1 Series D type
Product Name
S-13D1D1218-A6T2U3
S-13D1D1528-A6T2U3
S-13D1D1818-A6T2U3
S-13D1D1828-A6T2U3
S-13D1D1833-A6T2U3
S-13D1D2828-A6T2U3
S-13D1D2833-A6T2U3
S-13D1D2J2J-A6T2U3
Product Code
(1)
(2)
(3)
1
7
A
1
7
H
1
7
B
1
7
C
1
7
G
1
7
D
1
7
E
1
7
F
37
2.9±0.2
1.9±0.2
6
0.95
4
5
1
2
3
+0.1
0.15 -0.05
0.95
0.35±0.15
No. MP006-A-P-SD-2.1
TITLE
SOT236-A-PKG Dimensions
No.
MP006-A-P-SD-2.1
ANGLE
UNIT
mm
ABLIC Inc.
4.0±0.1(10 pitches:40.0±0.2)
+0.1
ø1.5 -0
+0.2
ø1.0 -0
2.0±0.05
0.25±0.1
4.0±0.1
1.4±0.2
3.2±0.2
3 2 1
4 5 6
Feed direction
No. MP006-A-C-SD-3.1
TITLE
SOT236-A-Carrier Tape
No.
MP006-A-C-SD-3.1
ANGLE
UNIT
mm
ABLIC Inc.
12.5max.
9.0±0.3
Enlarged drawing in the central part
ø13±0.2
(60°)
(60°)
No. MP006-A-R-SD-2.1
TITLE
SOT236-A-Reel
No.
MP006-A-R-SD-2.1
ANGLE
QTY
UNIT
mm
ABLIC Inc.
3,000
0.40
1.00±0.05
0.38±0.02
0.40
4
6
3
1
+0.05
0.08 -0.02
1.20±0.04
The heat sink of back side has different electric
potential depending on the product.
Confirm specifications of each product.
Do not use it as the function of electrode.
0.20±0.05
No. PM006-A-P-SD-1.1
TITLE
HSNT-6-B-PKG Dimensions
No.
PM006-A-P-SD-1.1
ANGLE
UNIT
mm
ABLIC Inc.
2.0±0.05
+0.1
ø1.5 -0
4.0±0.1
0.25±0.05
+0.1
ø0.5 -0
0.50±0.05
4.0±0.1
1.32±0.05
3
1
4
6
Feed direction
No. PM006-A-C-SD-2.0
TITLE
HSNT-6-B-C a r r i e r Tape
No.
PM006-A-C-SD-2.0
ANGLE
UNIT
mm
ABLIC Inc.
+1.0
9.0 - 0.0
11.4±1.0
Enlarged drawing in the central part
ø13±0.2
(60°)
(60°)
No. PM006-A-R-SD-1.0
TITLE
HSNT-6-B-Reel
No.
PM006-A-R-SD-1.0
ANGLE
UNIT
QTY.
mm
ABLIC Inc.
5,000
1.04min.
Land Pattern
0.24min.
1.02
0.40±0.02
0.40±0.02
(1.22)
Caution It is recommended to solder the heat sink to a board
in order to ensure the heat radiation.
PKG
Metal Mask Pattern
Aperture ratio
Aperture ratio
Caution
Mask aperture ratio of the lead mounting part is 100%.
Mask aperture ratio of the heat sink mounting part is 40%.
Mask thickness: t0.10mm to 0.12 mm
100%
40%
t0.10mm ~ 0.12 mm
TITLE
HSNT-6-B
-Land Recommendation
PM006-A-L-SD-2.0
No.
ANGLE
No. PM006-A-L-SD-2.0
UNIT
mm
ABLIC Inc.
Disclaimers (Handling Precautions)
1.
All the information described herein (product data, specifications, figures, tables, programs, algorithms and
application circuit examples, etc.) is current as of publishing date of this document and is subject to change without
notice.
2.
The circuit examples and the usages described herein are for reference only, and do not guarantee the success of
any specific mass-production design.
ABLIC Inc. is not liable for any losses, damages, claims or demands caused by the reasons other than the products
described herein (hereinafter "the products") or infringement of third-party intellectual property right and any other
right due to the use of the information described herein.
3.
ABLIC Inc. is not liable for any losses, damages, claims or demands caused by the incorrect information described
herein.
4.
Be careful to use the products within their ranges described herein. Pay special attention for use to the absolute
maximum ratings, operation voltage range and electrical characteristics, etc.
ABLIC Inc. is not liable for any losses, damages, claims or demands caused by failures and / or accidents, etc. due to
the use of the products outside their specified ranges.
5.
Before using the products, confirm their applications, and the laws and regulations of the region or country where they
are used and verify suitability, safety and other factors for the intended use.
6.
When exporting the products, comply with the Foreign Exchange and Foreign Trade Act and all other export-related
laws, and follow the required procedures.
7.
The products are strictly prohibited from using, providing or exporting for the purposes of the development of
weapons of mass destruction or military use. ABLIC Inc. is not liable for any losses, damages, claims or demands
caused by any provision or export to the person or entity who intends to develop, manufacture, use or store nuclear,
biological or chemical weapons or missiles, or use any other military purposes.
8.
The products are not designed to be used as part of any device or equipment that may affect the human body, human
life, or assets (such as medical equipment, disaster prevention systems, security systems, combustion control
systems, infrastructure control systems, vehicle equipment, traffic systems, in-vehicle equipment, aviation equipment,
aerospace equipment, and nuclear-related equipment), excluding when specified for in-vehicle use or other uses by
ABLIC, Inc. Do not apply the products to the above listed devices and equipments.
ABLIC Inc. is not liable for any losses, damages, claims or demands caused by unauthorized or unspecified use of
the products.
9.
In general, semiconductor products may fail or malfunction with some probability. The user of the products should
therefore take responsibility to give thorough consideration to safety design including redundancy, fire spread
prevention measures, and malfunction prevention to prevent accidents causing injury or death, fires and social
damage, etc. that may ensue from the products' failure or malfunction.
The entire system in which the products are used must be sufficiently evaluated and judged whether the products are
allowed to apply for the system on customer's own responsibility.
10. The products are not designed to be radiation-proof. The necessary radiation measures should be taken in the
product design by the customer depending on the intended use.
11. The products do not affect human health under normal use. However, they contain chemical substances and heavy
metals and should therefore not be put in the mouth. The fracture surfaces of wafers and chips may be sharp. Be
careful when handling these with the bare hands to prevent injuries, etc.
12. When disposing of the products, comply with the laws and ordinances of the country or region where they are used.
13. The information described herein contains copyright information and know-how of ABLIC Inc. The information
described herein does not convey any license under any intellectual property rights or any other rights belonging to
ABLIC Inc. or a third party. Reproduction or copying of the information from this document or any part of this
document described herein for the purpose of disclosing it to a third-party is strictly prohibited without the express
permission of ABLIC Inc.
14. For more details on the information described herein or any other questions, please contact ABLIC Inc.'s sales
representative.
15. This Disclaimers have been delivered in a text using the Japanese language, which text, despite any translations into
the English language and the Chinese language, shall be controlling.
2.4-2019.07
www.ablic.com
工商网监
湘ICP备2023018690号
