S-13R1 Series
www.ablic.com
5.5 V INPUT, 150 mA VOLTAGE REGULATOR
WITH REVERSE CURRENT PROTECTION
Rev.1.3_00
© ABLIC Inc., 2012-2018
The S-13R1 Series, developed by using the CMOS technology, is a positive voltage regulator IC of 150 mA output current,
which has low dropout voltage, high-accuracy output voltage and low current consumption.
Even with low current consumption of 5 μA typ., it has high ripple-rejection of 70 dB typ., and a ceramic capacitor of 1.0 μF or
more can be used as the input and output capacitors.
The S-13R1 Series includes an overcurrent protection circuit that prevents the load current from exceeding the current
capacity of the output transistor and a thermal shutdown circuit that prevents damage because of overheating.
Due to the built-in reverse current protection function, the reverse current flowing from the VOUT pin to the VIN pin can be
controlled as the small value 0.09 μA max. Therefore, IC protection diode is not needed.
Features
• Output voltage:
• Input voltage:
• Output voltage accuracy:
• Dropout voltage:
• Current consumption:
• Output current:
• Input and output capacitors:
• Ripple rejection:
• Reverse current protection function:
• Built-in overcurrent protection circuit:
• Built-in thermal shutdown circuit:
• Built-in ON / OFF circuit:
• Operation temperature range:
• Lead-free (Sn 100%), halogen-free
1.2 V to 4.0 V, selectable in 0.05 V step
2.0 V to 5.5 V
±1.0% (1.2 V to 1.45 V output product: ±15 mV)
150 mV typ. (3.0 V output product, IOUT = 100 mA)
During operation: 5 μA typ., 9 μA max.
During power-off: 0.1 μA typ., 1.0 μA max.
Possible to output 150 mA (VIN ≥ VOUT(S) + 1.0 V)*1
A ceramic capacitor of 1.0 μF or more can be used.
70 dB typ. (3.0 V output product, f = 1.0 kHz)
IREV = 0.09 μA max.
Limits overcurrent of output transistor.
Prevents damage caused by heat.
Ensures long battery life.
Discharge shunt function "available" / "unavailable" is selectable.
Pull-down function "available" / "unavailable" is selectable.
Ta = −40°C to +85°C
*1. Attention should be paid to the power dissipation of the package when the output current is large.
Applications
• Constant-voltage power supply for battery-powered device
• Constant-voltage power supply for portable equipment
• Constant-voltage power supply for home electric appliance
• Constant-voltage power supply for mobile phone
Packages
• SOT-23-5
• SC-82AB
• HSNT-4 (1010)
1
5.5 V INPUT, 150 mA VOLTAGE REGULATOR WITH REVERSE CURRENT PROTECTION
S-13R1 Series
Rev.1.3_00
Block Diagrams
1.
S-13R1 Series A type
VOUT
Function
Status
ON / OFF logic
Active "H"
Discharge shunt
Available
function
Constant current
Available
source pull-down
VOUT
Function
Status
ON / OFF logic
Active "H"
Discharge shunt
Available
function
Constant current
Unavailable
source pull-down
Reverse current
detection circuit
VIN
Overcurrent
protection circuit
Thermal shutdown circuit
ON / OFF
circuit
ON / OFF
+
−
*1
Reference
voltage
circuit
*1
VSS
*1.
Parasitic diode
Figure 1
2.
S-13R1 Series B type
Reverse current
detection circuit
VIN
Overcurrent
protection circuit
Thermal shutdown circuit
ON / OFF
ON / OFF
circuit
+
−
*1
Reference
voltage
circuit
*1
VSS
*1.
Parasitic diode
Figure 2
2
5.5 V INPUT, 150 mA VOLTAGE REGULATOR WITH REVERSE CURRENT PROTECTION
Rev.1.3_00
S-13R1 Series
3.
S-13R1 Series C type
VOUT
Function
Status
ON / OFF logic
Active "H"
Discharge shunt
Unavailable
function
Constant current
Available
source pull-down
VOUT
Function
Status
ON / OFF logic
Active "H"
Discharge shunt
Unavailable
function
Constant current
Unavailable
source pull-down
Reverse current
detection circuit
VIN
Overcurrent
protection circuit
Thermal shutdown circuit
ON / OFF
circuit
ON / OFF
+
−
*1
Reference
voltage
circuit
VSS
*1.
Parasitic diode
Figure 3
4.
S-13R1 Series D type
Reverse current
detection circuit
VIN
Overcurrent
protection circuit
Thermal shutdown circuit
ON / OFF
ON / OFF
circuit
+
−
*1
Reference
voltage
circuit
VSS
*1.
Parasitic diode
Figure 4
3
5.5 V INPUT, 150 mA VOLTAGE REGULATOR WITH REVERSE CURRENT PROTECTION
S-13R1 Series
Rev.1.3_00
Product Name Structure
Users can select the product type, output voltage, and package type for the S-13R1 Series. Refer to "1. Product
name" regarding the contents of product name, "2. Function list of product types" regarding the product type,
"3. Packages" regarding the package drawings, "4. Product name lists" regarding details of the product name.
1.
Product name
S-13R1
x
xx
-
xxxx
U
3
Environmental code
U:
Lead-free (Sn 100%), halogen-free
Package abbreviation and IC packing specifications*1
M5T1: SOT-23-5, Tape
N4T1: SC-82AB, Tape
A4T2: HSNT-4 (1010), Tape
Output voltage*2
12 to 40
(e.g., when the output voltage is 1.2 V, it is expressed as 12.)
Product type*3
A to D
*1.
*2.
*3.
2.
Refer to the tape drawing.
If you request the product which has 0.05 V step, contact our sales office.
Refer to "2. Function list of product types".
Function list of product types
Table 1
Product Type
A
B
C
D
3.
ON / OFF Logic
Active "H"
Active "H"
Active "H"
Active "H"
Constant Current Source Pull-down
Available
Unavailable
Available
Unavailable
Packages
Table 2
4
Discharge Shunt Function
Available
Available
Unavailable
Unavailable
Package Name
SOT-23-5
Dimension
MP005-A-P-SD
SC-82AB
NP004-A-P-SD
HSNT-4 (1010)
PL004-A-P-SD
Package Drawing Codes
Tape
MP005-A-C-SD
NP004-A-C-SD
NP004-A-C-S1
PL004-A-C-SD
Reel
MP005-A-R-SD
Land
−
NP004-A-R-SD
−
PL004-A-R-SD
PL004-A-L-SD
5.5 V INPUT, 150 mA VOLTAGE REGULATOR WITH REVERSE CURRENT PROTECTION
Rev.1.3_00
S-13R1 Series
4.
Product name lists
4. 1
S-13R1 Series A type
ON / OFF logic:
Discharge shunt function:
Active "H"
Available
Constant current source pull-down: Available
Table 3
Output Voltage
1.2 V ± 15 mV
1.3 V ± 15 mV
1.4 V ± 15 mV
1.5 V ± 1.0%
1.6 V ± 1.0%
1.7 V ± 1.0%
1.8 V ± 1.0%
1.85 V ± 1.0%
1.9 V ± 1.0%
2.0 V ± 1.0%
2.1 V ± 1.0%
2.2 V ± 1.0%
2.3 V ± 1.0%
2.4 V ± 1.0%
2.5 V ± 1.0%
2.6 V ± 1.0%
2.7 V ± 1.0%
2.8 V ± 1.0%
2.85 V ± 1.0%
2.9 V ± 1.0%
3.0 V ± 1.0%
3.1 V ± 1.0%
3.2 V ± 1.0%
3.3 V ± 1.0%
3.4 V ± 1.0%
3.5 V ± 1.0%
3.6 V ± 1.0%
3.7 V ± 1.0%
3.8 V ± 1.0%
3.9 V ± 1.0%
4.0 V ± 1.0%
Remark
SOT-23-5
S-13R1A12-M5T1U3
S-13R1A13-M5T1U3
S-13R1A14-M5T1U3
S-13R1A15-M5T1U3
S-13R1A16-M5T1U3
S-13R1A17-M5T1U3
S-13R1A18-M5T1U3
S-13R1A1J-M5T1U3
S-13R1A19-M5T1U3
S-13R1A20-M5T1U3
S-13R1A21-M5T1U3
S-13R1A22-M5T1U3
S-13R1A23-M5T1U3
S-13R1A24-M5T1U3
S-13R1A25-M5T1U3
S-13R1A26-M5T1U3
S-13R1A27-M5T1U3
S-13R1A28-M5T1U3
S-13R1A2J-M5T1U3
S-13R1A29-M5T1U3
S-13R1A30-M5T1U3
S-13R1A31-M5T1U3
S-13R1A32-M5T1U3
S-13R1A33-M5T1U3
S-13R1A34-M5T1U3
S-13R1A35-M5T1U3
S-13R1A36-M5T1U3
S-13R1A37-M5T1U3
S-13R1A38-M5T1U3
S-13R1A39-M5T1U3
S-13R1A40-M5T1U3
SC-82AB
S-13R1A12-N4T1U3
S-13R1A13-N4T1U3
S-13R1A14-N4T1U3
S-13R1A15-N4T1U3
S-13R1A16-N4T1U3
S-13R1A17-N4T1U3
S-13R1A18-N4T1U3
S-13R1A1J-N4T1U3
S-13R1A19-N4T1U3
S-13R1A20-N4T1U3
S-13R1A21-N4T1U3
S-13R1A22-N4T1U3
S-13R1A23-N4T1U3
S-13R1A24-N4T1U3
S-13R1A25-N4T1U3
S-13R1A26-N4T1U3
S-13R1A27-N4T1U3
S-13R1A28-N4T1U3
S-13R1A2J-N4T1U3
S-13R1A29-N4T1U3
S-13R1A30-N4T1U3
S-13R1A31-N4T1U3
S-13R1A32-N4T1U3
S-13R1A33-N4T1U3
S-13R1A34-N4T1U3
S-13R1A35-N4T1U3
S-13R1A36-N4T1U3
S-13R1A37-N4T1U3
S-13R1A38-N4T1U3
S-13R1A39-N4T1U3
S-13R1A40-N4T1U3
HSNT-4 (1010)
S-13R1A12-A4T2U3
S-13R1A13-A4T2U3
S-13R1A14-A4T2U3
S-13R1A15-A4T2U3
S-13R1A16-A4T2U3
S-13R1A17-A4T2U3
S-13R1A18-A4T2U3
S-13R1A1J-A4T2U3
S-13R1A19-A4T2U3
S-13R1A20-A4T2U3
S-13R1A21-A4T2U3
S-13R1A22-A4T2U3
S-13R1A23-A4T2U3
S-13R1A24-A4T2U3
S-13R1A25-A4T2U3
S-13R1A26-A4T2U3
S-13R1A27-A4T2U3
S-13R1A28-A4T2U3
S-13R1A2J-A4T2U3
S-13R1A29-A4T2U3
S-13R1A30-A4T2U3
S-13R1A31-A4T2U3
S-13R1A32-A4T2U3
S-13R1A33-A4T2U3
S-13R1A34-A4T2U3
S-13R1A35-A4T2U3
S-13R1A36-A4T2U3
S-13R1A37-A4T2U3
S-13R1A38-A4T2U3
S-13R1A39-A4T2U3
S-13R1A40-A4T2U3
Please contact our sales office for products with specifications other than the above.
5
5.5 V INPUT, 150 mA VOLTAGE REGULATOR WITH REVERSE CURRENT PROTECTION
S-13R1 Series
Rev.1.3_00
4. 2
S-13R1 Series B type
ON / OFF logic:
Discharge shunt function:
Active "H"
Available
Constant current source pull-down: Unavailable
Table 4
Output Voltage
1.2 V ± 15 mV
1.3 V ± 15 mV
1.4 V ± 15 mV
1.5 V ± 1.0%
1.6 V ± 1.0%
1.7 V ± 1.0%
1.8 V ± 1.0%
1.85 V ± 1.0%
1.9 V ± 1.0%
2.0 V ± 1.0%
2.1 V ± 1.0%
2.2 V ± 1.0%
2.3 V ± 1.0%
2.4 V ± 1.0%
2.5 V ± 1.0%
2.6 V ± 1.0%
2.7 V ± 1.0%
2.8 V ± 1.0%
2.85 V ± 1.0%
2.9 V ± 1.0%
3.0 V ± 1.0%
3.1 V ± 1.0%
3.2 V ± 1.0%
3.3 V ± 1.0%
3.4 V ± 1.0%
3.5 V ± 1.0%
3.6 V ± 1.0%
3.7 V ± 1.0%
3.8 V ± 1.0%
3.9 V ± 1.0%
4.0 V ± 1.0%
Remark
6
SOT-23-5
S-13R1B12-M5T1U3
S-13R1B13-M5T1U3
S-13R1B14-M5T1U3
S-13R1B15-M5T1U3
S-13R1B16-M5T1U3
S-13R1B17-M5T1U3
S-13R1B18-M5T1U3
S-13R1B1J-M5T1U3
S-13R1B19-M5T1U3
S-13R1B20-M5T1U3
S-13R1B21-M5T1U3
S-13R1B22-M5T1U3
S-13R1B23-M5T1U3
S-13R1B24-M5T1U3
S-13R1B25-M5T1U3
S-13R1B26-M5T1U3
S-13R1B27-M5T1U3
S-13R1B28-M5T1U3
S-13R1B2J-M5T1U3
S-13R1B29-M5T1U3
S-13R1B30-M5T1U3
S-13R1B31-M5T1U3
S-13R1B32-M5T1U3
S-13R1B33-M5T1U3
S-13R1B34-M5T1U3
S-13R1B35-M5T1U3
S-13R1B36-M5T1U3
S-13R1B37-M5T1U3
S-13R1B38-M5T1U3
S-13R1B39-M5T1U3
S-13R1B40-M5T1U3
SC-82AB
S-13R1B12-N4T1U3
S-13R1B13-N4T1U3
S-13R1B14-N4T1U3
S-13R1B15-N4T1U3
S-13R1B16-N4T1U3
S-13R1B17-N4T1U3
S-13R1B18-N4T1U3
S-13R1B1J-N4T1U3
S-13R1B19-N4T1U3
S-13R1B20-N4T1U3
S-13R1B21-N4T1U3
S-13R1B22-N4T1U3
S-13R1B23-N4T1U3
S-13R1B24-N4T1U3
S-13R1B25-N4T1U3
S-13R1B26-N4T1U3
S-13R1B27-N4T1U3
S-13R1B28-N4T1U3
S-13R1B2J-N4T1U3
S-13R1B29-N4T1U3
S-13R1B30-N4T1U3
S-13R1B31-N4T1U3
S-13R1B32-N4T1U3
S-13R1B33-N4T1U3
S-13R1B34-N4T1U3
S-13R1B35-N4T1U3
S-13R1B36-N4T1U3
S-13R1B37-N4T1U3
S-13R1B38-N4T1U3
S-13R1B39-N4T1U3
S-13R1B40-N4T1U3
HSNT-4 (1010)
S-13R1B12-A4T2U3
S-13R1B13-A4T2U3
S-13R1B14-A4T2U3
S-13R1B15-A4T2U3
S-13R1B16-A4T2U3
S-13R1B17-A4T2U3
S-13R1B18-A4T2U3
S-13R1B1J-A4T2U3
S-13R1B19-A4T2U3
S-13R1B20-A4T2U3
S-13R1B21-A4T2U3
S-13R1B22-A4T2U3
S-13R1B23-A4T2U3
S-13R1B24-A4T2U3
S-13R1B25-A4T2U3
S-13R1B26-A4T2U3
S-13R1B27-A4T2U3
S-13R1B28-A4T2U3
S-13R1B2J-A4T2U3
S-13R1B29-A4T2U3
S-13R1B30-A4T2U3
S-13R1B31-A4T2U3
S-13R1B32-A4T2U3
S-13R1B33-A4T2U3
S-13R1B34-A4T2U3
S-13R1B35-A4T2U3
S-13R1B36-A4T2U3
S-13R1B37-A4T2U3
S-13R1B38-A4T2U3
S-13R1B39-A4T2U3
S-13R1B40-A4T2U3
Please contact our sales office for products with specifications other than the above.
5.5 V INPUT, 150 mA VOLTAGE REGULATOR WITH REVERSE CURRENT PROTECTION
Rev.1.3_00
S-13R1 Series
4. 3
S-13R1 Series C type
ON / OFF logic:
Discharge shunt function:
Active "H"
Unavailable
Constant current source pull-down: Available
Table 5
Output Voltage
1.2 V ± 15 mV
1.3 V ± 15 mV
1.4 V ± 15 mV
1.5 V ± 1.0%
1.6 V ± 1.0%
1.7 V ± 1.0%
1.8 V ± 1.0%
1.85 V ± 1.0%
1.9 V ± 1.0%
2.0 V ± 1.0%
2.1 V ± 1.0%
2.2 V ± 1.0%
2.3 V ± 1.0%
2.4 V ± 1.0%
2.5 V ± 1.0%
2.6 V ± 1.0%
2.7 V ± 1.0%
2.8 V ± 1.0%
2.85 V ± 1.0%
2.9 V ± 1.0%
3.0 V ± 1.0%
3.1 V ± 1.0%
3.2 V ± 1.0%
3.3 V ± 1.0%
3.4 V ± 1.0%
3.5 V ± 1.0%
3.6 V ± 1.0%
3.7 V ± 1.0%
3.8 V ± 1.0%
3.9 V ± 1.0%
4.0 V ± 1.0%
Remark
SOT-23-5
S-13R1C12-M5T1U3
S-13R1C13-M5T1U3
S-13R1C14-M5T1U3
S-13R1C15-M5T1U3
S-13R1C16-M5T1U3
S-13R1C17-M5T1U3
S-13R1C18-M5T1U3
S-13R1C1J-M5T1U3
S-13R1C19-M5T1U3
S-13R1C20-M5T1U3
S-13R1C21-M5T1U3
S-13R1C22-M5T1U3
S-13R1C23-M5T1U3
S-13R1C24-M5T1U3
S-13R1C25-M5T1U3
S-13R1C26-M5T1U3
S-13R1C27-M5T1U3
S-13R1C28-M5T1U3
S-13R1C2J-M5T1U3
S-13R1C29-M5T1U3
S-13R1C30-M5T1U3
S-13R1C31-M5T1U3
S-13R1C32-M5T1U3
S-13R1C33-M5T1U3
S-13R1C34-M5T1U3
S-13R1C35-M5T1U3
S-13R1C36-M5T1U3
S-13R1C37-M5T1U3
S-13R1C38-M5T1U3
S-13R1C39-M5T1U3
S-13R1C40-M5T1U3
SC-82AB
S-13R1C12-N4T1U3
S-13R1C13-N4T1U3
S-13R1C14-N4T1U3
S-13R1C15-N4T1U3
S-13R1C16-N4T1U3
S-13R1C17-N4T1U3
S-13R1C18-N4T1U3
S-13R1C1J-N4T1U3
S-13R1C19-N4T1U3
S-13R1C20-N4T1U3
S-13R1C21-N4T1U3
S-13R1C22-N4T1U3
S-13R1C23-N4T1U3
S-13R1C24-N4T1U3
S-13R1C25-N4T1U3
S-13R1C26-N4T1U3
S-13R1C27-N4T1U3
S-13R1C28-N4T1U3
S-13R1C2J-N4T1U3
S-13R1C29-N4T1U3
S-13R1C30-N4T1U3
S-13R1C31-N4T1U3
S-13R1C32-N4T1U3
S-13R1C33-N4T1U3
S-13R1C34-N4T1U3
S-13R1C35-N4T1U3
S-13R1C36-N4T1U3
S-13R1C37-N4T1U3
S-13R1C38-N4T1U3
S-13R1C39-N4T1U3
S-13R1C40-N4T1U3
HSNT-4 (1010)
S-13R1C12-A4T2U3
S-13R1C13-A4T2U3
S-13R1C14-A4T2U3
S-13R1C15-A4T2U3
S-13R1C16-A4T2U3
S-13R1C17-A4T2U3
S-13R1C18-A4T2U3
S-13R1C1J-A4T2U3
S-13R1C19-A4T2U3
S-13R1C20-A4T2U3
S-13R1C21-A4T2U3
S-13R1C22-A4T2U3
S-13R1C23-A4T2U3
S-13R1C24-A4T2U3
S-13R1C25-A4T2U3
S-13R1C26-A4T2U3
S-13R1C27-A4T2U3
S-13R1C28-A4T2U3
S-13R1C2J-A4T2U3
S-13R1C29-A4T2U3
S-13R1C30-A4T2U3
S-13R1C31-A4T2U3
S-13R1C32-A4T2U3
S-13R1C33-A4T2U3
S-13R1C34-A4T2U3
S-13R1C35-A4T2U3
S-13R1C36-A4T2U3
S-13R1C37-A4T2U3
S-13R1C38-A4T2U3
S-13R1C39-A4T2U3
S-13R1C40-A4T2U3
Please contact our sales office for products with specifications other than the above.
7
5.5 V INPUT, 150 mA VOLTAGE REGULATOR WITH REVERSE CURRENT PROTECTION
S-13R1 Series
Rev.1.3_00
4. 4
S-13R1 Series D type
ON / OFF logic:
Discharge shunt function:
Active "H"
Unavailable
Constant current source pull-down: Unavailable
Table 6
Output Voltage
1.2 V ± 15 mV
1.3 V ± 15 mV
1.4 V ± 15 mV
1.5 V ± 1.0%
1.6 V ± 1.0%
1.7 V ± 1.0%
1.8 V ± 1.0%
1.85 V ± 1.0%
1.9 V ± 1.0%
2.0 V ± 1.0%
2.1 V ± 1.0%
2.2 V ± 1.0%
2.3 V ± 1.0%
2.4 V ± 1.0%
2.5 V ± 1.0%
2.6 V ± 1.0%
2.7 V ± 1.0%
2.8 V ± 1.0%
2.85 V ± 1.0%
2.9 V ± 1.0%
3.0 V ± 1.0%
3.1 V ± 1.0%
3.2 V ± 1.0%
3.3 V ± 1.0%
3.4 V ± 1.0%
3.5 V ± 1.0%
3.6 V ± 1.0%
3.7 V ± 1.0%
3.8 V ± 1.0%
3.9 V ± 1.0%
4.0 V ± 1.0%
Remark
8
SOT-23-5
S-13R1D12-M5T1U3
S-13R1D13-M5T1U3
S-13R1D14-M5T1U3
S-13R1D15-M5T1U3
S-13R1D16-M5T1U3
S-13R1D17-M5T1U3
S-13R1D18-M5T1U3
S-13R1D1J-M5T1U3
S-13R1D19-M5T1U3
S-13R1D20-M5T1U3
S-13R1D21-M5T1U3
S-13R1D22-M5T1U3
S-13R1D23-M5T1U3
S-13R1D24-M5T1U3
S-13R1D25-M5T1U3
S-13R1D26-M5T1U3
S-13R1D27-M5T1U3
S-13R1D28-M5T1U3
S-13R1D2J-M5T1U3
S-13R1D29-M5T1U3
S-13R1D30-M5T1U3
S-13R1D31-M5T1U3
S-13R1D32-M5T1U3
S-13R1D33-M5T1U3
S-13R1D34-M5T1U3
S-13R1D35-M5T1U3
S-13R1D36-M5T1U3
S-13R1D37-M5T1U3
S-13R1D38-M5T1U3
S-13R1D39-M5T1U3
S-13R1D40-M5T1U3
SC-82AB
S-13R1D12-N4T1U3
S-13R1D13-N4T1U3
S-13R1D14-N4T1U3
S-13R1D15-N4T1U3
S-13R1D16-N4T1U3
S-13R1D17-N4T1U3
S-13R1D18-N4T1U3
S-13R1D1J-N4T1U3
S-13R1D19-N4T1U3
S-13R1D20-N4T1U3
S-13R1D21-N4T1U3
S-13R1D22-N4T1U3
S-13R1D23-N4T1U3
S-13R1D24-N4T1U3
S-13R1D25-N4T1U3
S-13R1D26-N4T1U3
S-13R1D27-N4T1U3
S-13R1D28-N4T1U3
S-13R1D2J-N4T1U3
S-13R1D29-N4T1U3
S-13R1D30-N4T1U3
S-13R1D31-N4T1U3
S-13R1D32-N4T1U3
S-13R1D33-N4T1U3
S-13R1D34-N4T1U3
S-13R1D35-N4T1U3
S-13R1D36-N4T1U3
S-13R1D37-N4T1U3
S-13R1D38-N4T1U3
S-13R1D39-N4T1U3
S-13R1D40-N4T1U3
HSNT-4 (1010)
S-13R1D12-A4T2U3
S-13R1D13-A4T2U3
S-13R1D14-A4T2U3
S-13R1D15-A4T2U3
S-13R1D16-A4T2U3
S-13R1D17-A4T2U3
S-13R1D18-A4T2U3
S-13R1D1J-A4T2U3
S-13R1D19-A4T2U3
S-13R1D20-A4T2U3
S-13R1D21-A4T2U3
S-13R1D22-A4T2U3
S-13R1D23-A4T2U3
S-13R1D24-A4T2U3
S-13R1D25-A4T2U3
S-13R1D26-A4T2U3
S-13R1D27-A4T2U3
S-13R1D28-A4T2U3
S-13R1D2J-A4T2U3
S-13R1D29-A4T2U3
S-13R1D30-A4T2U3
S-13R1D31-A4T2U3
S-13R1D32-A4T2U3
S-13R1D33-A4T2U3
S-13R1D34-A4T2U3
S-13R1D35-A4T2U3
S-13R1D36-A4T2U3
S-13R1D37-A4T2U3
S-13R1D38-A4T2U3
S-13R1D39-A4T2U3
S-13R1D40-A4T2U3
Please contact our sales office for products with specifications other than the above.
5.5 V INPUT, 150 mA VOLTAGE REGULATOR WITH REVERSE CURRENT PROTECTION
Rev.1.3_00
S-13R1 Series
Pin Configurations
1.
SOT-23-5
Top view
5
4
1 2 3
Table 7
Pin No.
1
2
3
4
5
Symbol
VIN
VSS
ON / OFF
NC*1
VOUT
Description
Input voltage pin
GND pin
ON / OFF pin
No connection
Output voltage pin
Figure 5
*1. The NC pin is electrically open.
The NC pin can be connected to the VIN pin or the VSS pin.
2.
SC-82AB
Top view
4
3
1
2
Table 8
Pin No.
1
2
3
4
Symbol
ON / OFF
VSS
VOUT
VIN
Description
ON / OFF pin
GND pin
Output voltage pin
Input voltage pin
Figure 6
3.
HSNT-4 (1010)
Top view
1
2
4
3
Bottom view
4
3
Table 9
Pin No.
1
2
3
4
Symbol
VOUT
VSS
ON / OFF
VIN
Description
Output voltage pin
GND pin
ON / OFF pin
Input voltage pin
1
2
*1
Figure 7
*1. Connect the heat sink of backside at shadowed area to the board, and set electric potential GND.
However, do not use it as the function of electrode.
9
5.5 V INPUT, 150 mA VOLTAGE REGULATOR WITH REVERSE CURRENT PROTECTION
S-13R1 Series
Rev.1.3_00
Absolute Maximum Ratings
Table 10
Item
Symbol
VIN
VON / OFF
VOUT
IOUT
Input voltage
Output voltage
Output current
SOT-23-5
PD
SC-82AB
HSNT-4 (1010)
Operation ambient temperature
Topr
Storage temperature
Tstg
*1. When mounted on board
[Mounted board]
(1) Board size:
114.3 mm × 76.2 mm × t1.6 mm
(2) Name:
JEDEC STANDARD51-7
Power dissipation
Caution
(Ta = +25°C unless otherwise specified)
Absolute Maximum Rating
Unit
VSS − 0.3 to VSS + 6.0
VSS − 0.3 to VSS + 6.0
VSS − 0.3 to VSS + 6.0
200
600*1
400*1
340*1
−40 to +85
−40 to +125
The absolute maximum ratings are rated values exceeding which the product could suffer physical
damage. These values must therefore not be exceeded under any conditions.
Power Dissipation (PD) [mW]
1200
Figure 8
SOT-23-5
1000
SC-82AB
800
HSNT-4 (1010)
600
400
200
0
10
V
V
V
mA
mW
mW
mW
°C
°C
0
150
100
50
Ambient Temperature (Ta) [°C]
Power Dissipation of Package (When Mounted on Board)
5.5 V INPUT, 150 mA VOLTAGE REGULATOR WITH REVERSE CURRENT PROTECTION
Rev.1.3_00
S-13R1 Series
Power Dissipation of HSNT-4 (1010) (Reference)
Power dissipation of package differs depending on the mounting conditions.
Consider the power dissipation characteristics under the following conditions as reference.
[Mounted board]
(1) Board size:
(2) Board material:
(3) Wiring ratio:
(4) Test conditions:
(5) Land pattern:
40 mm × 40 mm × t0.8 mm
Glass epoxy resin (four layers)
50%
When mounted on board (wind speed: 0 m/s)
Refer to the recommended land pattern (drawing code: PL004-A-L-SD)
Power Dissipation (PD) [mW]
1200
1000
800
600
400
200
0
Figure 9
0
150
100
50
Ambient Temperature (Ta) [°C]
Power Dissipation of Package (When Mounted on Board)
Table 11
Condition
HSNT-4 (1010) (When mounted on board)
Power Dissipation (Reference)
870 mW
Thermal Resistance Value (θj−a)
115°C/W
11
5.5 V INPUT, 150 mA VOLTAGE REGULATOR WITH REVERSE CURRENT PROTECTION
S-13R1 Series
Rev.1.3_00
Electrical Characteristics
Table 12 (1 /2)
Item
Symbol
Output voltage*1
Output current
*2
Dropout voltage*3
Line regulation
Load regulation
Output voltage
temperature
*4
coefficient
Current consumption
during operation
Reverse current
Current consumption
during power-off
Input voltage
ON / OFF pin
input voltage "H"
ON / OFF pin
input voltage "L"
ON / OFF pin
input current "H"
VOUT(E)
IOUT
Vdrop
Condition
VIN = VOUT(S) + 1.0 V,
IOUT = 30 mA
1.2 V ≤ VOUT(S) < 1.5 V
1.5 V ≤ VOUT(S) ≤ 4.0 V
VIN ≥ VOUT(S) + 1.0 V
IOUT = 100 mA
1.2 V ≤ VOUT(S) < 1.3 V
1.3 V ≤ VOUT(S) < 1.4 V
1.4 V ≤ VOUT(S) < 1.5 V
1.5 V ≤ VOUT(S) < 1.6 V
1.6 V ≤ VOUT(S) < 1.7 V
1.7 V ≤ VOUT(S) < 1.8 V
1.8 V ≤ VOUT(S) < 2.0 V
2.0 V ≤ VOUT(S) < 2.8 V
2.8 V ≤ VOUT(S) < 3.0 V
3.0 V ≤ VOUT(S) ≤ 4.0 V
2.0 V ≤ VIN ≤ 5.5 V,
1.2 V ≤ VOUT(S) < 1.5 V
ΔVOUT1 IOUT = 30 mA
ΔVIN•VOUT VOUT(S) + 0.5 V ≤ VIN ≤ 5.5 V,
1.5 V ≤ VOUT(S) ≤ 4.0 V
IOUT = 30 mA
ΔVOUT2
VIN = VOUT(S) + 1.0 V, 10 μA ≤ IOUT ≤ 100 mA
ΔVOUT
VIN = VOUT(S) + 1.0 V, IOUT = 100 mA,
ΔTa•VOUT −40°C ≤ Ta ≤ +85°C
ISS1
IREV
ISS2
VIN
VSH
VSL
ISH
VIN = VOUT(S) + 1.0 V, ON / OFF pin = ON,
no load
0 V ≤ VIN < VOUT
VIN = VOUT(S) + 1.0 V, ON / OFF pin = OFF,
no load
−
VIN = VOUT(S) + 1.0 V, RL = 1.0 kΩ,
determined by VOUT output level
VIN = VOUT(S) + 1.0 V, RL = 1.0 kΩ,
determined by VOUT output level
B / D type
(without constant current
source pull-down)
VIN = 5.5 V,
VON / OFF = 5.5 V
A / C type
(with constant current
source pull-down)
(Ta = +25°C unless otherwise specified)
Test
Min.
Typ.
Max.
Unit
Circuit
VOUT(S)
VOUT(S)
V
V
1
− 0.015 OUT(S) + 0.015
VOUT(S)
VOUT(S)
VOUT(S)
V
1
× 0.99
× 1.01
*5
150
mA
3
−
−
0.80
0.84
0.88
V
1
0.74
0.78
−
V
1
0.64
0.68
−
V
1
0.54
0.58
−
V
1
0.44
0.48
−
V
1
0.34
0.38
−
V
1
0.24
0.28
−
V
1
0.19
0.28
−
V
1
0.17
0.23
−
V
1
0.15
0.23
−
V
1
−
0.05
0.2
%/V
1
−
0.05
0.2
%/V
1
−
25
40
mV
1
−
±100
−
ppm/°C
1
−
5.0
9.0
μA
2
−
−
0.09
μA
6
−
0.1
1.0
μA
2
2.0
−
5.5
V
−
1.0
−
−
V
4
−
−
0.3
V
4
−0.1
−
0.1
μA
4
0.05
0.10
0.20
μA
4
−0.1
−
0.1
μA
4
−
70
−
dB
5
ON / OFF pin
input current "L"
ISL
VIN = VOUT(S) + 1.0 V, VON / OFF = 0 V
Ripple rejection
|RR|
VIN = VOUT(S) + 1.0 V, f = 1.0 kHz,
ΔVrip = 0.5 Vrms, IOUT = 100 mA
Limit current
ILIM
VIN = VOUT(S) + 1.0 V, ON / OFF pin = ON
200
250
400
mA
3
Short-circuit current
Ishort
VIN = VOUT(S) + 1.0 V, ON / OFF pin = ON,
VOUT = 0 V
−
30
−
mA
3
Junction temperature
−
150
−
°C
−
Junction temperature
−
120
−
°C
−
Thermal shutdown
T
detection temperature SD
Thermal shutdown
TSR
release temperature
12
5.5 V INPUT, 150 mA VOLTAGE REGULATOR WITH REVERSE CURRENT PROTECTION
Rev.1.3_00
S-13R1 Series
Table 12 (2 /2)
Item
Discharge shunt
resistance during
power-off
Reverse current
protection mode
detection voltage
Reverse current
protection mode
release voltage
Symbol
Condition
RLOW
VIN = 5.5 V,
VOUT = 0.1 V
VREVD
VREVR
A / B type
(with discharge shunt function)
(Ta = +25°C unless otherwise specified)
Test
Min.
Typ.
Max.
Unit
Circuit
−
35
−
Ω
3
0 V ≤ VIN ≤ 5.5 V, VOUT ≥ 0.5 V,
VREVD = VIN − VOUT
20
45
100
mV
6
0 V ≤ VIN ≤ 5.5 V, VOUT ≥ 0.5 V,
VREVR = VIN − VOUT
50
75
120
mV
6
*1. VOUT(S): Set output voltage
VOUT(E): Actual output voltage
Output voltage when fixing IOUT (= 30 mA) and inputting VOUT(S) + 1.0 V
*2. The output current at which the output voltage becomes 95% of VOUT(E) after gradually increasing the output current.
*3. Vdrop = VIN1 − (VOUT3 × 0.98)
VOUT3 is the output voltage when VIN = VOUT(S) + 1.0 V and IOUT = 100 mA.
VIN1 is the input voltage at which the output voltage becomes 98% of VOUT3 after gradually decreasing the input
voltage.
*4. A change in the temperature of the output voltage [mV/°C] is calculated using the following equation.
ΔVOUT
ΔVOUT
[mV/°C]*1 = VOUT(S) [V]*2 × ΔTa•V
[ppm/°C]*3 ÷ 1000
ΔTa
OUT
*1. Change in temperature of output voltage
*2. Set output voltage
*3. Output voltage temperature coefficient
*5. The output current can be at least this value.
Due to restrictions on the package power dissipation, this value may not be satisfied. Attention should be paid to the
power dissipation of the package when the output current is large.
This specification is guaranteed by design.
13
5.5 V INPUT, 150 mA VOLTAGE REGULATOR WITH REVERSE CURRENT PROTECTION
S-13R1 Series
Rev.1.3_00
Test Circuits
+
VOUT
VIN
ON / OFF
VSS
V
A
+
Set to ON
Figure 10
+
A
Test Circuit 1
VOUT
VIN
ON / OFF
VSS
Set to VIN or GND
Figure 11
Test Circuit 2
VOUT
VIN
A
ON / OFF
V
+
VSS
Set to VIN or GND
Figure 12
Test Circuit 3
VOUT
VIN
+
A
ON / OFF
V
+
VSS
Figure 13
Test Circuit 4
VOUT
VIN
ON / OFF
V
+
VSS
Set to ON
Figure 14
Test Circuit 5
VOUT
VIN
ON / OFF
Set to ON
14
A
+
V
VSS
Figure 15
RL
Test Circuit 6
+
RL
5.5 V INPUT, 150 mA VOLTAGE REGULATOR WITH REVERSE CURRENT PROTECTION
Rev.1.3_00
S-13R1 Series
Standard Circuit
Input
Output
VOUT
VIN
CIN
*1
ON / OFF
VSS
Single GND
CL
*2
GND
*1. CIN is a capacitor for stabilizing the input.
*2. A ceramic capacitor of 1.0 F or more can be used as CL.
Figure 16
Caution
The above connection diagram and constants will not guarantee successful operation. Perform
thorough evaluation using the actual application to set the constants.
Condition of Application
Input capacitor (CIN):
Output capacitor (CL):
1.0 F or more
1.0 F or more
Caution Generally a series regulator may cause oscillation, depending on the selection of external parts.
Confirm that no oscillation occurs in the application for which the above capacitors are used.
Selection of Input and Output Capacitors (CIN, CL)
The S-13R1 Series requires an output capacitor between the VOUT pin and the VSS pin for phase compensation.
Operation is stabilized by a ceramic capacitor with an output capacitance of 1.0 F or more over the entire temperature
range. When using an OS capacitor, a tantalum capacitor, or an aluminum electrolytic capacitor, the capacitance must
be 1.0 F or more.
The value of the output overshoot or undershoot transient response varies depending on the value of the output
capacitor. The required capacitance of the input capacitor differs depending on the application.
The recommended capacitance for an application is CIN 1.0 F, CL 1.0 F; however, when selecting the output
capacitor, perform sufficient evaluation, including evaluation of temperature characteristics, on the actual device.
15
5.5 V INPUT, 150 mA VOLTAGE REGULATOR WITH REVERSE CURRENT PROTECTION
S-13R1 Series
Rev.1.3_00
Explanation of Terms
1.
Low dropout voltage regulator
This voltage regulator has the low dropout voltage due to its built-in low on-resistance transistor.
2.
Output voltage (VOUT)
The accuracy of the output voltage is ensured at ±1.0% or ±15 mV*1 under the specified conditions of fixed input
voltage*2, fixed output current, and fixed temperature.
*1.
*2.
When VOUT(S) < 1.5 V: ±15 mV, when VOUT(S) ≥ 1.5 V: ±1.0%
Differs depending on the product.
Caution
3.
If the above conditions change, the output voltage value may vary and exceed the accuracy range
of the output voltage. Refer to " Electrical Characteristics" and " Characteristics (Typical Data)"
for details.
ΔVOUT1
Line regulation
ΔVIN•VOUT
Indicates the dependency of the output voltage on the input voltage. That is, the values show how much the output
voltage changes due to a change in the input voltage with the output current remaining unchanged.
4.
Load regulation (ΔVOUT2)
Indicates the dependency of the output voltage on the output current. That is, the values show how much the output
voltage changes due to a change in the output current with the input voltage remaining unchanged.
5.
Dropout voltage (Vdrop)
Indicates the difference between input voltage (VIN1) and the output voltage when; decreasing input voltage (VIN)
gradually until the output voltage has dropped out to the value of 98% of output voltage (VOUT3), which is at
VIN = VOUT(S) + 1.0 V.
Vdrop = VIN1 − (VOUT3 × 0.98)
16
5.5 V INPUT, 150 mA VOLTAGE REGULATOR WITH REVERSE CURRENT PROTECTION
Rev.1.3_00
S-13R1 Series
6.
ΔVOUT
Output voltage temperature coefficient
ΔTa•VOUT
The shaded area in Figure 17 is the range where VOUT varies in the operation temperature range when the output
voltage temperature coefficient is ±100 ppm/°C.
Example of S-13R1A30 typ. product
VOUT
[V]
+0.30 mV/°C
VOUT(E)*1
−0.30 mV/°C
−40
*1.
+25
+85
Ta [°C]
VOUT(E) is the value of the output voltage measured at Ta = +25°C.
Figure 17
A change in the temperature of the output voltage [mV/°C] is calculated using the following equation.
ΔVOUT
ΔVOUT
[mV/°C]*1 = VOUT(S) [V]*2 × ΔTa•V
[ppm/°C]*3 ÷ 1000
ΔTa
OUT
*1. Change in temperature of output voltage
*2. Set output voltage
*3. Output voltage temperature coefficient
17
5.5 V INPUT, 150 mA VOLTAGE REGULATOR WITH REVERSE CURRENT PROTECTION
S-13R1 Series
Rev.1.3_00
Operation
1.
Basic operation
Figure 18 shows the block diagram of the S-13R1 Series.
The error amplifier compares the reference voltage (Vref) with feedback voltage (Vfb), which is the output voltage
resistance-divided by feedback resistors (Rs, Rf). It supplies the gate voltage necessary to maintain the constant output
voltage which is not influenced by the input voltage and temperature change, to the output transistor.
VIN
*1
Current
supply
Error
amplifier
Vref
VOUT
−
Rf
+
Vfb
Reference voltage
circuit
Rs
VSS
*1.
Parasitic diode
Figure 18
2.
Output transistor
In the S-13R1 Series, a low on-resistance P-channel MOS FET is used as the output transistor.
Since there exists a parasitic diode between the VIN pin and the VOUT pin, the reverse current arises when potential of
VOUT becomes higher than VIN. However, the reverse current detection circuit prevents the current from flowing from
the VOUT pin in the S-13R1 Series. Therefore, the IC is not damaged even when the potential of VOUT becomes higher
than VIN.
18
5.5 V INPUT, 150 mA VOLTAGE REGULATOR WITH REVERSE CURRENT PROTECTION
Rev.1.3_00
S-13R1 Series
3.
ON / OFF pin
This pin starts and stops the regulator.
When the ON / OFF pin is set to OFF level, the entire internal circuit stops operating, and the built-in
P-channel MOS FET output transistor between the VIN pin and the VOUT pin is turned off, reducing current
consumption significantly.
Note that the current consumption increases when a voltage of 0.3 V to 1.0 V is applied to the ON / OFF pin. The
ON / OFF pin is configured as shown in Figure 19 and Figure 20.
3. 1
S-13R1 Series A / C type
The ON / OFF pin is internally pulled down to the VSS pin in the floating status, so the VOUT pin is set to the VSS
level.
3. 2
S-13R1 Series B / D type
The ON / OFF pin is not internally pulled down to the VSS pin, so do not use this pin in the floating status. When
not using the ON / OFF pin, connect the pin to the VIN pin.
Table 13
Product Type
ON / OFF Pin
Internal Circuit
VOUT Pin Voltage
Current Consumption
*1
A/B/C/D
"H": ON
Operate
Set value
ISS1
A/B
"L": OFF
Stop
VSS level
ISS2
C/D
"L": OFF
Stop
High-Z ≅ VSS level
ISS2
*1. Note that the IC’s current consumption increases as much as current flows into the constant current of
0.1 μA typ. when the ON / OFF pin is connected to the VIN pin and the S-13R1 Series A / C type is
operating (refer to Figure 19).
VIN
VIN
ON / OFF
ON / OFF
VSS
Figure 19
S-13R1 Series A / C type
VSS
Figure 20
S-13R1 Series B / D type
19
5.5 V INPUT, 150 mA VOLTAGE REGULATOR WITH REVERSE CURRENT PROTECTION
S-13R1 Series
Rev.1.3_00
4.
Discharge shunt function (S-13R1 Series A / B type)
The S-13R1 Series A / B type has a built-in discharge shunt circuit to discharge the output capacitance.
The output capacitance is discharged as follows so that the VOUT pin reaches the VSS level.
(1) The ON / OFF pin is set to OFF level.
(2) The output transistor is turned off.
(3) The discharge shunt circuit is turned on.
(4) The output capacitor discharges.
Since the S-13R1 Series C / D type does not have a discharge shunt circuit, the VOUT pin is not discharged. The
S-13R1 Series A / B type allows the VOUT pin to reach the VSS level rapidly due to the discharge shunt circuit.
S-13R1 Series
Output transistor: OFF
VOUT
VIN
Discharge shunt circuit
: ON
*1
ON / OFF
ON / OFF circuit
Output
capacitor
(CL)
ON / OFF Pin
: OFF
Current flow
GND
VSS
*1. Parasitic diode
Figure 21
5.
Constant current source pull-down (S-13R1 Series A / C type)
The ON / OFF pin is internally pulled down to the VSS pin in the floating status, so the VOUT pin is set to the VSS level.
Note that the IC's current consumption increases as much as current flows into the constant current of 0.1 μA typ.
when the ON / OFF pin is connected to the VIN pin and the S-13R1 Series A / C type is operating.
20
5.5 V INPUT, 150 mA VOLTAGE REGULATOR WITH REVERSE CURRENT PROTECTION
Rev.1.3_00
S-13R1 Series
6.
Overcurrent protection circuit
The S-13R1 Series has an overcurrent protection circuit having the characteristics shown in "1. Output voltage vs.
Output current (When load current increases) (Ta = +25°C)" in " Characteristics (Typical Data)", in order to
protect the output transistor against an excessive output current and short circuiting between the VOUT pin and the
VSS pin. The current (Ishort) when the output pin is short-circuited is internally set at approx. 30 mA typ., and the normal
value is restored for the output voltage, if releasing a short circuit once.
Caution This overcurrent protection circuit does not work as for thermal protection. If this IC long keeps
short circuiting inside, pay attention to the conditions of input voltage and load current so that,
under the usage conditions including short circuit, the loss of the IC will not exceed power
dissipation of the package.
7.
Thermal shutdown circuit
The S-13R1 Series has a thermal shutdown circuit to protect the device from damage due to overheat. When the
junction temperature rises to 150°C typ., the thermal shutdown circuit operates to stop regulating. When the junction
temperature drops to 120°C typ., the thermal shutdown circuit is released to restart regulating.
Due to self-heating of the S-13R1 Series, if the thermal shutdown circuit starts operating, it stops regulating so that
the output voltage drops. When regulation stops, the S-13R1 Series does not itself generate heat and the IC's
temperature drops. When the temperature drops, the thermal shutdown circuit is released to restart regulating, thus
the S-13R1 Series generates heat again. Repeating this procedure makes the waveform of the output voltage into a
pulse-like form. Stop or restart of regulation continues unless decreasing either or both of the input voltage and the
output current in order to reduce the internal power consumption, or decreasing the ambient temperature.
Table 14
Thermal Shutdown Circuit
Operate: 150°C typ.*1
Release: 120°C typ.*1
*1. Junction temperature
VOUT Pin Voltage
VSS level
Set value
21
5.5 V INPUT, 150 mA VOLTAGE REGULATOR WITH REVERSE CURRENT PROTECTION
S-13R1 Series
Rev.1.3_00
8.
Reverse current protection function
8. 1
Detection and release of reverse current protection mode
The reverse current protection function compares values of the VIN pin voltage (VIN) and the VOUT pin voltage
(VOUT), and prevents the current from flowing to the VIN pin and the VSS pin from the VOUT pin. Also, in the
S-13R1 Series A / B type, the current flows from the VOUT pin to the VSS pin due to a discharge shunt circuit.
During the reverse current protection mode, the connection direction of parasitic diode of the output transistor is
switched by the reverse current protection circuit, and the feedback resistors (Rs, Rf) and the VSS pin are
disconnected.
The reverse current is prevented by switching the reverse current protection mode before VIN becomes lower than
VOUT.
As shown in Figure 24, in the case of VIN − VOUT > VREVD, the S-13R1 Series is in normal operation mode. The
reverse current protection mode is detected when VIN − VOUT ≤ VREVD.
In order to insure the stable operation, there is also a hysteresis for detection and release of the reverse current
protection mode. Therefore, the reverse current protection mode is released when VIN − VOUT ≥ VREVR.
The reverse current detection circuit operates at 0 V ≤ VIN ≤ 5.5 V and VOUT ≥ 0.5 V.
Current flow
VIN
VIN
Current
supply
Error
amplifier
Current
supply
−
Error
amplifier
−
+
+
Reverse current
detection circuit
Reference voltage
circuit
VOUT
Reverse current
detection circuit
Rf
Rf
VOUT
Reference voltage
circuit
Rs
Rs
Reverse
current
(IREV)
Current
flow
VSS
VSS
Figure 22
Normal Operation Mode
VIN
Figure 23
Reverse current protection
mode detection voltage (VREVD)
Reverse Current Protection Mode
Reverse current protection
mode release voltage (VREVR)
VOUT + VREVR
VOUT + VREVD
VOUT
Normal operation mode
Reverse current protection mode
Figure 24
22
Normal operation mode
5.5 V INPUT, 150 mA VOLTAGE REGULATOR WITH REVERSE CURRENT PROTECTION
Rev.1.3_00
S-13R1 Series
8. 2
Power-on (ON / OFF pin = ON)
At power-on, the reverse current protection mode and the normal operation mode may be repeated during the time
period of VIN − VOUT ≤ VREVD.
VIN = VON / OFF
VOUT
VIN − VOUT
Reverse current protection mode
/ normal operation mode
Normal operation mode
Figure 25
23
5.5 V INPUT, 150 mA VOLTAGE REGULATOR WITH REVERSE CURRENT PROTECTION
S-13R1 Series
Rev.1.3_00
Precautions
• Wiring patterns for the VIN pin, the VOUT pin and GND should be designed so that the impedance is low. When
mounting an output capacitor between the VOUT pin and the VSS pin (CL) and the capacitor for stabilizing the input
between the VIN pin and the VSS pin (CIN), the distance from the capacitors to these pins should be as short as
possible.
• Note that generally the output voltage may increase when a series regulator is used at low load current (10 μA or
less).
If the S-13R1 Series is used at low load current (several hundred nA), the output voltage may increase due to the
leakage current from an output driver at high temperature, and the reverse current protection mode may not be
released. Perform sufficient evaluation with the actual device in use.
• Note that the output voltage may increase due to the leakage current from an output driver even if the ON / OFF pin is
at OFF level when a series regulator is used at high temperature.
• Generally a series regulator may cause oscillation, depending on the selection of external parts. The following
conditions are recommended for the S-13R1 Series. However, be sure to perform sufficient evaluation under the
actual usage conditions for selection, including evaluation of temperature characteristics. Refer to "5. Example of
equivalent series resistance vs. Output current characteristics (Ta = +25°C)" in " Reference Data" for the
equivalent series resistance (RESR) of the output capacitor.
Input capacitor (CIN):
Output capacitor (CL):
1.0 μF or more
1.0 μF or more
• The voltage regulator may oscillate when the impedance of the power supply is high and the input capacitance is small
or an input capacitor is not connected.
• If the output capacitance is small, power supply's fluctuation and the characteristics of load fluctuation become worse.
Sufficiently evaluate the output voltage's fluctuation with the actual device.
• Overshoot may occur in the output voltage momentarily if the voltage is rapidly raised at power-on or when the power
supply fluctuates. Sufficiently evaluate the output voltage at power-on with the actual device.
• The application conditions for the input voltage, the output voltage, and the load current should not exceed the
package power dissipation.
• Do not apply an electrostatic discharge to this IC that exceeds the performance ratings of the built-in electrostatic
protection circuit.
• In determining the output current, attention should be paid to the output current value specified in Table 12 in
" Electrical Characteristics" and footnote *5 of the table.
• ABLIC Inc. claims no responsibility for any disputes arising out of or in connection with any infringement by products
including this IC of patents owned by a third party.
24
5.5 V INPUT, 150 mA VOLTAGE REGULATOR WITH REVERSE CURRENT PROTECTION
Rev.1.3_00
S-13R1 Series
Characteristics (Typical Data)
Output voltage vs. Output current (When load current increases) (Ta = +25°C)
1. 1
VOUT(S) = 1.2 V
VOUT [V]
VOUT(S) = 3.0 V
3.6
1.4
1.2
1.0
0.8
0.6
0.4
0.2
0
3.0
VIN = 2.0 V
VIN = 2.2 V
VIN = 3.2 V
VIN = 3.5 V
VIN = 4.0 V
VIN = 5.0 V
VIN = 5.5 V
2.4
1.8
1.2
0.6
VIN = 5.5 V
0
1. 3
1. 2
VOUT [V]
1.
0
50 100 150 200 250 300 350 400
IOUT [mA]
0
50 100 150 200 250 300 350 400
IOUT [mA]
VOUT(S) = 4.0 V
4.5
VOUT [V]
3.6
Remark
VIN = 4.5 V
VIN = 5.0 V
VIN = 5.5 V
2.7
1.8
0.9
0
0
50 100 150 200 250 300 350 400
IOUT [mA]
Output voltage vs. Input voltage (Ta = +25°C)
VOUT [V]
2. 1
VOUT(S) = 1.2 V
2. 2
3.6
1.2
3.0
0.9
IOUT = 100 mA
IOUT = 30 mA
IOUT = 1 mA
IOUT = 100 μA
0.6
0.3
IOUT = 100 mA
IOUT = 30 mA
IOUT = 1 mA
IOUT = 100 μA
1.8
1.2
0
0
VOUT [V]
2.4
0.6
0
2. 3
VOUT(S) = 3.0 V
1.5
VOUT [V]
2.
In determining the output current, attention should
be paid to the following.
1. The minimum output current value and
footnote *5 of Table 12 in " Electrical
Characteristics"
2. The package power dissipation
1
2
3
VIN [V]
4
5
6
0
1
2
3
VIN [V]
4
5
6
VOUT(S) = 4.0 V
4.5
4.0
3.5
3.0
2.5
2.0
1.5
1.0
0.5
0
IOUT = 100 mA
IOUT = 30 mA
IOUT = 1 mA
IOUT = 100 μA
0
1
2
3
VIN [V]
4
5
6
25
5.5 V INPUT, 150 mA VOLTAGE REGULATOR WITH REVERSE CURRENT PROTECTION
S-13R1 Series
Rev.1.3_00
Dropout voltage vs. Output current
3. 1
VOUT(S) = 1.2 V
Vdrop [V]
0.50
0.45
0.40
0.35
0.30
0.25
0.20
0.15
0.10
0.05
0
Ta = +85°C
Ta = +25°C
Ta = −40°C
0
3. 3
Vdrop [V]
0.50
0.45
0.40
0.35
0.30
0.25
0.20
0.15
0.10
0.05
0
50
100
75
IOUT [mA]
125
150
125
150
0.50
0.45
0.40
0.35
0.30
0.25
0.20
0.15
0.10
0.05
0
Ta = +85°C
Ta = +25°C
Ta = −40°C
0
25
50
100
75
IOUT [mA]
125
Ta = +85°C
Ta = +25°C
Ta = −40°C
25
50
100
75
IOUT [mA]
Vdrop [V]
Dropout voltage vs. Set output voltage
0.50
0.45
0.40
0.35
0.30
0.25
0.20
0.15
0.10
0.05
0
IOUT = 150 mA
IOUT = 100 mA
IOUT = 30 mA
IOUT = 10 mA
IOUT = 1 mA
1.0
Remark
26
25
VOUT(S) = 3.0 V
VOUT(S) = 4.0 V
0
4.
3. 2
Vdrop [V]
3.
1.6
2.2
2.8
VOUT(S) [V]
3.4
4.0
In dashed line areas, the reverse current protection mode and the normal operation mode are repeated.
150
5.5 V INPUT, 150 mA VOLTAGE REGULATOR WITH REVERSE CURRENT PROTECTION
Rev.1.3_00
S-13R1 Series
Output voltage vs. Ambient temperature
VOUT [V]
5. 1
VOUT(S) = 1.2 V
5. 2
3.30
1.26
3.15
1.20
1.08
3.00
2.85
1.14
5. 3
VOUT(S) = 3.0 V
1.32
VOUT [V]
5.
−40 −25
2.70
0
25
Ta [°C]
50
75 85
0
25
Ta [°C]
50
75 85
−40 −25
0
25
Ta [°C]
75 85
50
VOUT(S) = 4.0 V
4.20
VOUT [V]
4.10
4.00
3.90
3.80
6.
−40 −25
Current consumption vs. Input voltage
6. 1
VOUT(S) = 1.2 V
6. 2
10
ISS1 [μA]
ISS1 [μA]
8
6
4
2
0
1
2
3
VIN [V]
6
Ta = +85°C
Ta = +25°C
Ta = −40°C
4
2
Ta = −40°C
0
6. 3
10
Ta = +85°C
Ta = +25°C
8
VOUT(S) = 3.0 V
0
4
5
6
4
5
6
0
1
2
3
VIN [V]
4
5
6
VOUT(S) = 4.0 V
10
ISS1 [μA]
8
Ta = +85°C
Ta = +25°C
Ta = −40°C
6
4
2
0
0
1
2
3
VIN [V]
27
5.5 V INPUT, 150 mA VOLTAGE REGULATOR WITH REVERSE CURRENT PROTECTION
S-13R1 Series
Rev.1.3_00
7.
Reverse current vs. VOUT pin voltage
7. 1
VIN = 0 V
100
Ta = +85°C
Ta = +25°C
IREV [nA]
80
60
40
Ta = −40°C
20
0
0
8.
1
2
3
4
VOUT [V]
5
6
Ripple rejection (Ta = +25°C)
8. 1
VOUT(S) = 1.2 V
8. 2
VOUT(S) = 3.0 V
120
100
80
60
IOUT = 1 mA
IOUT = 30 mA
IOUT = 100 mA
IOUT = 150 mA
40
20
0
10
8. 3
100
1k
10k
100k
Frequency [Hz]
1M
VOUT(S) = 4.0 V
Ripple Rejection [dB]
VIN = 5.0 V, CL = 1.0 μF
120
100
80
60
IOUT = 1 mA
IOUT = 30 mA
IOUT = 100 mA
IOUT = 150 mA
40
20
0
10
28
100
1k
10k
100k
Frequency [Hz]
VIN = 4.0 V, CL = 1.0 μF
Ripple Rejection [dB]
Ripple Rejection [dB]
VIN = 2.2 V, CL = 1.0 μF
1M
120
100
80
60
IOUT = 1 mA
IOUT = 30 mA
IOUT = 100 mA
IOUT = 150 mA
40
20
0
10
100
1k
10k
100k
Frequency [Hz]
1M
5.5 V INPUT, 150 mA VOLTAGE REGULATOR WITH REVERSE CURRENT PROTECTION
Rev.1.3_00
S-13R1 Series
Reference Data
1.
Transient response characteristics when input (Ta = +25°C)
1. 1
VOUT(S) = 1.2 V
1. 2
IOUT = 30 mA, CIN = CL = 1.0 μF, VIN = 4.0 V ↔ 5.0 V, tr = tf = 5.0 μs
7.0
3.20
6.0
3.15
5.0
3.10
VIN
4.0
3.05
3.0
3.00
VOUT
2.0
2.95
1.0
2.90
0
2.85
−400 −200
0
200 400 600 800
t [μs]
VIN [V]
VIN [V]
VOUT [V]
VOUT [V]
IOUT = 30 mA, CIN = CL = 1.0 μF, VIN = 2.2 V ↔ 3.2 V, tr = tf = 5.0 μs
4.0
1.40
3.5
1.35
3.0
1.30
2.5
1.25
VIN
2.0
1.20
VOUT
1.5
1.15
1.0
1.10
0.5
1.05
0
1.00
−400 −200
0
200 400 600 800
t [μs]
1. 3 VOUT(S) = 4.0 V
VOUT(S) = 3.0 V
VIN [V]
VOUT [V]
IOUT = 30 mA, CIN = CL = 1.0 μF, VIN = 5.0 V ↔ 5.5 V, tr = tf = 5.0 μs
7.0
4.15
6.0
4.10
VIN
5.0
4.05
4.0
4.00
VOUT
3.0
3.95
2.0
3.90
1.0
3.85
0
3.80
−400 −200
0
200 400 600 800
t [μs]
Transient response characteristics of load (Ta = +25°C)
VOUT(S) = 1.2 V
2. 2
IOUT
VOUT
−200 −100
0
100
t [μs]
200
300
400
200
100
0
−100
−200
−300
−400
−500
−600
VOUT [V]
1.40
1.35
1.30
1.25
1.20
1.15
1.10
1.05
1.00
VIN = 2.2 V, CIN = CL = 1.0 μF, IOUT = 1 mA ↔ 150 mA
IOUT [mA]
VOUT [V]
VIN = 2.2 V, CIN = CL = 1.0 μF, IOUT = 50 mA ↔ 100 mA
2.00
1.80
1.60
IOUT
1.40
1.20
VOUT
1.00
0.80
0.60
−200 −100
VOUT
−400 −200
0
200
t [μs]
400
600
800
VIN = 4.0 V, CIN = CL = 1.0 μF, IOUT = 1 mA ↔ 150 mA
VOUT [V]
IOUT
200
100
0
−100
−200
−300
−400
−500
−600
IOUT [mA]
VOUT [V]
100 200 300 400 500
t [μs]
VOUT(S) = 3.0 V
VIN = 4.0 V, CIN = CL = 1.0 μF, IOUT = 50 mA ↔ 100 mA
3.20
3.15
3.10
3.05
3.00
2.95
2.90
2.85
2.80
0
200
100
0
−100
−200
−300
−400
−500
IOUT [mA]
2. 1
3.80
3.60
3.40
IOUT
3.20
3.00
VOUT
2.80
2.60
2.40
2.20
−400 −200
0
200 400 600 800 1000
t [μs]
200
100
0
−100
−200
−300
−400
−500
−600
IOUT [mA]
2.
29
5.5 V INPUT, 150 mA VOLTAGE REGULATOR WITH REVERSE CURRENT PROTECTION
S-13R1 Series
Rev.1.3_00
VOUT(S) = 4.0 V
VOUT
−400 −200
0
200
t [μs]
400
800
3. 2
VIN = 2.2 V, CIN = CL = 1.0 μF, IOUT = 100 mA,
VON / OFF = 0 V → 2.2 V, tr = 1.0 μs
6
5
4
4
4
VON / OFF
3
2
2
0
VOUT
1
−2
0
0
3. 3
100
200
300
t [μs]
400
500
600
−4
VOUT
−800 −400
0
400
t [μs]
800
1200 1600
4
VON / OFF
VOUT
3
2
2
0
1
−2
0
0
200 400 600 800 1000 1200 1400
t [μs]
−4
3
VIN = 4.0 V, CIN = CL = 1.0 μF, IOUT = 100 mA,
VON / OFF = 0 V → 4.0 V, tr = 1.0 μs
6
VON / OFF
4
VOUT
2
2
0
1
−2
0
VIN = 5.0 V, CIN = CL = 1.0 μF, IOUT = 100 mA,
VON / OFF = 0 V → 5.0 V, tr = 1.0 μs
6
4
VOUT(S) = 3.0 V
0
VOUT(S) = 4.0 V
5
VOUT [V]
5
VOUT [V]
IOUT
200
100
0
−100
−200
−300
−400
−500
−600
200 400 600 800 1000 1200 1400
t [μs]
−4
VON / OFF [V]
VOUT(S) = 1.2 V
VON / OFF [V]
3. 1
30
4.60
4.40
4.20
4.00
3.80
3.60
3.40
3.20
3.00
Transient response characteristics of ON / OFF pin when rising (Ta = +25°C)
3.
VOUT [V]
600
VOUT [V]
IOUT
200
100
0
−100
−200
−300
−400
−500
−600
VON / OFF [V]
VOUT [V]
4.20
4.15
4.10
4.05
4.00
3.95
3.90
3.85
3.80
VIN = 5.0 V, CIN = CL = 1.0 μF, IOUT = 1 mA ↔ 150 mA
IOUT [mA]
VIN = 5.0 V, CIN = CL = 1.0 μF, IOUT = 50 mA ↔ 100 mA
IOUT [mA]
2. 3
5.5 V INPUT, 150 mA VOLTAGE REGULATOR WITH REVERSE CURRENT PROTECTION
Rev.1.3_00
S-13R1 Series
4.
Output capacitance vs. Characteristics of discharge time (Ta = +25°C)
tDSC [ms]
VIN = VOUT(S) + 1.0 V, CIN = 1.0 μF, IOUT = no load,
VON / OFF = VOUT(S) + 1.0 V → 0 V, tf = 1.0 μs
1.6
1.4
1.2
1.0
0.8
0.6
0.4
0.2
0
1.0 μs
VON / OFF
VOUT(S) = 1.2 V
VOUT(S) = 3.0 V
VOUT(S) = 4.0 V
VSS
tDSC
VOUT
0
2
4
6
CL [μF]
8
10
12
VOUT × 10%
VIN = VOUT + 1.0 V
VON / OFF = VOUT + 1.0 V → VSS
Figure 26 S-13R1 Series A / B type
(with discharge shunt function)
5.
Figure 27
Test Condition of Discharge Time
Example of equivalent series resistance vs. Output current characteristics (Ta = +25°C)
CIN = CL = 1.0 μF
RESR [Ω]
100
CIN
Stable
ON / OFF
0
0.01
VIN
VOUT
VSS
CL
*1
RESR
150
IOUT [mA]
*1.
Figure 28
CL: ROHM Co.,Ltd. MCH184FN105Z (1.0 μF)
Figure 29
31
5.5 V INPUT, 150 mA VOLTAGE REGULATOR WITH REVERSE CURRENT PROTECTION
S-13R1 Series
Rev.1.3_00
Marking Specifications
1.
SOT-23-5
Top view
5
(1) to (3):
(4):
4
Product code (Refer to Product name vs. Product code)
Lot number
(1) (2) (3) (4)
1
2
3
Product name vs. Product code
1. 1
S-13R1 Series A type
Product Name
S-13R1A12-M5T1U3
S-13R1A13-M5T1U3
S-13R1A14-M5T1U3
S-13R1A15-M5T1U3
S-13R1A16-M5T1U3
S-13R1A17-M5T1U3
S-13R1A18-M5T1U3
S-13R1A1J-M5T1U3
S-13R1A19-M5T1U3
S-13R1A20-M5T1U3
S-13R1A21-M5T1U3
S-13R1A22-M5T1U3
S-13R1A23-M5T1U3
S-13R1A24-M5T1U3
S-13R1A25-M5T1U3
S-13R1A26-M5T1U3
S-13R1A27-M5T1U3
S-13R1A28-M5T1U3
S-13R1A2J-M5T1U3
S-13R1A29-M5T1U3
S-13R1A30-M5T1U3
S-13R1A31-M5T1U3
S-13R1A32-M5T1U3
S-13R1A33-M5T1U3
S-13R1A34-M5T1U3
S-13R1A35-M5T1U3
S-13R1A36-M5T1U3
S-13R1A37-M5T1U3
S-13R1A38-M5T1U3
S-13R1A39-M5T1U3
S-13R1A40-M5T1U3
32
1. 2
(1)
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
Product Code
(2)
(3)
A
A
A
B
A
C
A
D
A
E
A
F
A
G
A
5
A
H
A
I
A
J
A
K
A
L
A
M
A
N
A
O
A
P
A
Q
A
6
A
R
A
S
A
T
A
U
A
V
A
W
A
X
A
Y
A
Z
A
2
A
3
A
4
S-13R1 Series B type
Product Name
S-13R1B12-M5T1U3
S-13R1B13-M5T1U3
S-13R1B14-M5T1U3
S-13R1B15-M5T1U3
S-13R1B16-M5T1U3
S-13R1B17-M5T1U3
S-13R1B18-M5T1U3
S-13R1B1J-M5T1U3
S-13R1B19-M5T1U3
S-13R1B20-M5T1U3
S-13R1B21-M5T1U3
S-13R1B22-M5T1U3
S-13R1B23-M5T1U3
S-13R1B24-M5T1U3
S-13R1B25-M5T1U3
S-13R1B26-M5T1U3
S-13R1B27-M5T1U3
S-13R1B28-M5T1U3
S-13R1B2J-M5T1U3
S-13R1B29-M5T1U3
S-13R1B30-M5T1U3
S-13R1B31-M5T1U3
S-13R1B32-M5T1U3
S-13R1B33-M5T1U3
S-13R1B34-M5T1U3
S-13R1B35-M5T1U3
S-13R1B36-M5T1U3
S-13R1B37-M5T1U3
S-13R1B38-M5T1U3
S-13R1B39-M5T1U3
S-13R1B40-M5T1U3
(1)
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
Product Code
(2)
(3)
B
A
B
B
B
C
B
D
B
E
B
F
B
G
B
5
B
H
B
I
B
J
B
K
B
L
B
M
B
N
B
O
B
P
B
Q
B
6
B
R
B
S
B
T
B
U
B
V
B
W
B
X
B
Y
B
Z
B
2
B
3
B
4
5.5 V INPUT, 150 mA VOLTAGE REGULATOR WITH REVERSE CURRENT PROTECTION
Rev.1.3_00
S-13R1 Series
1. 3
S-13R1 Series C type
Product Name
S-13R1C12-M5T1U3
S-13R1C13-M5T1U3
S-13R1C14-M5T1U3
S-13R1C15-M5T1U3
S-13R1C16-M5T1U3
S-13R1C17-M5T1U3
S-13R1C18-M5T1U3
S-13R1C1J-M5T1U3
S-13R1C19-M5T1U3
S-13R1C20-M5T1U3
S-13R1C21-M5T1U3
S-13R1C22-M5T1U3
S-13R1C23-M5T1U3
S-13R1C24-M5T1U3
S-13R1C25-M5T1U3
S-13R1C26-M5T1U3
S-13R1C27-M5T1U3
S-13R1C28-M5T1U3
S-13R1C2J-M5T1U3
S-13R1C29-M5T1U3
S-13R1C30-M5T1U3
S-13R1C31-M5T1U3
S-13R1C32-M5T1U3
S-13R1C33-M5T1U3
S-13R1C34-M5T1U3
S-13R1C35-M5T1U3
S-13R1C36-M5T1U3
S-13R1C37-M5T1U3
S-13R1C38-M5T1U3
S-13R1C39-M5T1U3
S-13R1C40-M5T1U3
1. 4
Product Code
(1)
(2)
(3)
2
C
A
2
C
B
2
C
C
2
C
D
2
C
E
2
C
F
2
C
G
2
C
5
2
C
H
2
C
I
2
C
J
2
C
K
2
C
L
2
C
M
2
C
N
2
C
O
2
C
P
2
C
Q
2
C
6
2
C
R
2
C
S
2
C
T
2
C
U
2
C
V
2
C
W
2
C
X
2
C
Y
2
C
Z
2
C
2
2
C
3
2
C
4
S-13R1 Series D type
Product Name
S-13R1D12-M5T1U3
S-13R1D13-M5T1U3
S-13R1D14-M5T1U3
S-13R1D15-M5T1U3
S-13R1D16-M5T1U3
S-13R1D17-M5T1U3
S-13R1D18-M5T1U3
S-13R1D1J-M5T1U3
S-13R1D19-M5T1U3
S-13R1D20-M5T1U3
S-13R1D21-M5T1U3
S-13R1D22-M5T1U3
S-13R1D23-M5T1U3
S-13R1D24-M5T1U3
S-13R1D25-M5T1U3
S-13R1D26-M5T1U3
S-13R1D27-M5T1U3
S-13R1D28-M5T1U3
S-13R1D2J-M5T1U3
S-13R1D29-M5T1U3
S-13R1D30-M5T1U3
S-13R1D31-M5T1U3
S-13R1D32-M5T1U3
S-13R1D33-M5T1U3
S-13R1D34-M5T1U3
S-13R1D35-M5T1U3
S-13R1D36-M5T1U3
S-13R1D37-M5T1U3
S-13R1D38-M5T1U3
S-13R1D39-M5T1U3
S-13R1D40-M5T1U3
Product Code
(1)
(2)
(3)
2
D
A
2
D
B
2
D
C
2
D
D
2
D
E
2
D
F
2
D
G
2
D
5
2
D
H
2
D
I
2
D
J
2
D
K
2
D
L
2
D
M
2
D
N
2
D
O
2
D
P
2
D
Q
2
D
6
2
D
R
2
D
S
2
D
T
2
D
U
2
D
V
2
D
W
2
D
X
2
D
Y
2
D
Z
2
D
2
2
D
3
2
D
4
33
5.5 V INPUT, 150 mA VOLTAGE REGULATOR WITH REVERSE CURRENT PROTECTION
S-13R1 Series
Rev.1.3_00
2.
SC-82AB
Top view
4
(1) to (3):
3
Product code (Refer to Product name vs. Product code)
(1) (2) (3)
1
2
Product name vs. Product code
2. 1
S-13R1 Series A type
Product Name
S-13R1A12-N4T1U3
S-13R1A13-N4T1U3
S-13R1A14-N4T1U3
S-13R1A15-N4T1U3
S-13R1A16-N4T1U3
S-13R1A17-N4T1U3
S-13R1A18-N4T1U3
S-13R1A1J-N4T1U3
S-13R1A19-N4T1U3
S-13R1A20-N4T1U3
S-13R1A21-N4T1U3
S-13R1A22-N4T1U3
S-13R1A23-N4T1U3
S-13R1A24-N4T1U3
S-13R1A25-N4T1U3
S-13R1A26-N4T1U3
S-13R1A27-N4T1U3
S-13R1A28-N4T1U3
S-13R1A2J-N4T1U3
S-13R1A29-N4T1U3
S-13R1A30-N4T1U3
S-13R1A31-N4T1U3
S-13R1A32-N4T1U3
S-13R1A33-N4T1U3
S-13R1A34-N4T1U3
S-13R1A35-N4T1U3
S-13R1A36-N4T1U3
S-13R1A37-N4T1U3
S-13R1A38-N4T1U3
S-13R1A39-N4T1U3
S-13R1A40-N4T1U3
34
2. 2
(1)
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
Product Code
(2)
(3)
A
A
A
B
A
C
A
D
A
E
A
F
A
G
A
5
A
H
A
I
A
J
A
K
A
L
A
M
A
N
A
O
A
P
A
Q
A
6
A
R
A
S
A
T
A
U
A
V
A
W
A
X
A
Y
A
Z
A
2
A
3
A
4
S-13R1 Series B type
Product Name
S-13R1B12-N4T1U3
S-13R1B13-N4T1U3
S-13R1B14-N4T1U3
S-13R1B15-N4T1U3
S-13R1B16-N4T1U3
S-13R1B17-N4T1U3
S-13R1B18-N4T1U3
S-13R1B1J-N4T1U3
S-13R1B19-N4T1U3
S-13R1B20-N4T1U3
S-13R1B21-N4T1U3
S-13R1B22-N4T1U3
S-13R1B23-N4T1U3
S-13R1B24-N4T1U3
S-13R1B25-N4T1U3
S-13R1B26-N4T1U3
S-13R1B27-N4T1U3
S-13R1B28-N4T1U3
S-13R1B2J-N4T1U3
S-13R1B29-N4T1U3
S-13R1B30-N4T1U3
S-13R1B31-N4T1U3
S-13R1B32-N4T1U3
S-13R1B33-N4T1U3
S-13R1B34-N4T1U3
S-13R1B35-N4T1U3
S-13R1B36-N4T1U3
S-13R1B37-N4T1U3
S-13R1B38-N4T1U3
S-13R1B39-N4T1U3
S-13R1B40-N4T1U3
(1)
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
Product Code
(2)
(3)
B
A
B
B
B
C
B
D
B
E
B
F
B
G
B
5
B
H
B
I
B
J
B
K
B
L
B
M
B
N
B
O
B
P
B
Q
B
6
B
R
B
S
B
T
B
U
B
V
B
W
B
X
B
Y
B
Z
B
2
B
3
B
4
5.5 V INPUT, 150 mA VOLTAGE REGULATOR WITH REVERSE CURRENT PROTECTION
Rev.1.3_00
S-13R1 Series
2. 3
S-13R1 Series C type
Product Name
S-13R1C12-N4T1U3
S-13R1C13-N4T1U3
S-13R1C14-N4T1U3
S-13R1C15-N4T1U3
S-13R1C16-N4T1U3
S-13R1C17-N4T1U3
S-13R1C18-N4T1U3
S-13R1C1J-N4T1U3
S-13R1C19-N4T1U3
S-13R1C20-N4T1U3
S-13R1C21-N4T1U3
S-13R1C22-N4T1U3
S-13R1C23-N4T1U3
S-13R1C24-N4T1U3
S-13R1C25-N4T1U3
S-13R1C26-N4T1U3
S-13R1C27-N4T1U3
S-13R1C28-N4T1U3
S-13R1C2J-N4T1U3
S-13R1C29-N4T1U3
S-13R1C30-N4T1U3
S-13R1C31-N4T1U3
S-13R1C32-N4T1U3
S-13R1C33-N4T1U3
S-13R1C34-N4T1U3
S-13R1C35-N4T1U3
S-13R1C36-N4T1U3
S-13R1C37-N4T1U3
S-13R1C38-N4T1U3
S-13R1C39-N4T1U3
S-13R1C40-N4T1U3
2. 4
Product Code
(1)
(2)
(3)
2
C
A
2
C
B
2
C
C
2
C
D
2
C
E
2
C
F
2
C
G
2
C
5
2
C
H
2
C
I
2
C
J
2
C
K
2
C
L
2
C
M
2
C
N
2
C
O
2
C
P
2
C
Q
2
C
6
2
C
R
2
C
S
2
C
T
2
C
U
2
C
V
2
C
W
2
C
X
2
C
Y
2
C
Z
2
C
2
2
C
3
2
C
4
S-13R1 Series D type
Product Name
S-13R1D12-N4T1U3
S-13R1D13-N4T1U3
S-13R1D14-N4T1U3
S-13R1D15-N4T1U3
S-13R1D16-N4T1U3
S-13R1D17-N4T1U3
S-13R1D18-N4T1U3
S-13R1D1J-N4T1U3
S-13R1D19-N4T1U3
S-13R1D20-N4T1U3
S-13R1D21-N4T1U3
S-13R1D22-N4T1U3
S-13R1D23-N4T1U3
S-13R1D24-N4T1U3
S-13R1D25-N4T1U3
S-13R1D26-N4T1U3
S-13R1D27-N4T1U3
S-13R1D28-N4T1U3
S-13R1D2J-N4T1U3
S-13R1D29-N4T1U3
S-13R1D30-N4T1U3
S-13R1D31-N4T1U3
S-13R1D32-N4T1U3
S-13R1D33-N4T1U3
S-13R1D34-N4T1U3
S-13R1D35-N4T1U3
S-13R1D36-N4T1U3
S-13R1D37-N4T1U3
S-13R1D38-N4T1U3
S-13R1D39-N4T1U3
S-13R1D40-N4T1U3
Product Code
(1)
(2)
(3)
2
D
A
2
D
B
2
D
C
2
D
D
2
D
E
2
D
F
2
D
G
2
D
5
2
D
H
2
D
I
2
D
J
2
D
K
2
D
L
2
D
M
2
D
N
2
D
O
2
D
P
2
D
Q
2
D
6
2
D
R
2
D
S
2
D
T
2
D
U
2
D
V
2
D
W
2
D
X
2
D
Y
2
D
Z
2
D
2
2
D
3
2
D
4
35
5.5 V INPUT, 150 mA VOLTAGE REGULATOR WITH REVERSE CURRENT PROTECTION
S-13R1 Series
Rev.1.3_00
3.
HSNT-4 (1010)
Top view
4
(1) to (3):
(4), (5):
3
Product code (Refer to Product name vs. Product code)
Lot number
(1) (2) (3)
(4) (5)
1
2
Product name vs. Product code
3. 1
S-13R1 Series A type
Product Name
S-13R1A12-A4T2U3
S-13R1A13-A4T2U3
S-13R1A14-A4T2U3
S-13R1A15-A4T2U3
S-13R1A16-A4T2U3
S-13R1A17-A4T2U3
S-13R1A18-A4T2U3
S-13R1A1J-A4T2U3
S-13R1A19-A4T2U3
S-13R1A20-A4T2U3
S-13R1A21-A4T2U3
S-13R1A22-A4T2U3
S-13R1A23-A4T2U3
S-13R1A24-A4T2U3
S-13R1A25-A4T2U3
S-13R1A26-A4T2U3
S-13R1A27-A4T2U3
S-13R1A28-A4T2U3
S-13R1A2J-A4T2U3
S-13R1A29-A4T2U3
S-13R1A30-A4T2U3
S-13R1A31-A4T2U3
S-13R1A32-A4T2U3
S-13R1A33-A4T2U3
S-13R1A34-A4T2U3
S-13R1A35-A4T2U3
S-13R1A36-A4T2U3
S-13R1A37-A4T2U3
S-13R1A38-A4T2U3
S-13R1A39-A4T2U3
S-13R1A40-A4T2U3
36
3. 2
(1)
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
Product Code
(2)
(3)
A
A
A
B
A
C
A
D
A
E
A
F
A
G
A
5
A
H
A
I
A
J
A
K
A
L
A
M
A
N
A
O
A
P
A
Q
A
6
A
R
A
S
A
T
A
U
A
V
A
W
A
X
A
Y
A
Z
A
2
A
3
A
4
S-13R1 Series B type
Product Name
S-13R1B12-A4T2U3
S-13R1B13-A4T2U3
S-13R1B14-A4T2U3
S-13R1B15-A4T2U3
S-13R1B16-A4T2U3
S-13R1B17-A4T2U3
S-13R1B18-A4T2U3
S-13R1B1J-A4T2U3
S-13R1B19-A4T2U3
S-13R1B20-A4T2U3
S-13R1B21-A4T2U3
S-13R1B22-A4T2U3
S-13R1B23-A4T2U3
S-13R1B24-A4T2U3
S-13R1B25-A4T2U3
S-13R1B26-A4T2U3
S-13R1B27-A4T2U3
S-13R1B28-A4T2U3
S-13R1B2J-A4T2U3
S-13R1B29-A4T2U3
S-13R1B30-A4T2U3
S-13R1B31-A4T2U3
S-13R1B32-A4T2U3
S-13R1B33-A4T2U3
S-13R1B34-A4T2U3
S-13R1B35-A4T2U3
S-13R1B36-A4T2U3
S-13R1B37-A4T2U3
S-13R1B38-A4T2U3
S-13R1B39-A4T2U3
S-13R1B40-A4T2U3
(1)
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
Product Code
(2)
(3)
B
A
B
B
B
C
B
D
B
E
B
F
B
G
B
5
B
H
B
I
B
J
B
K
B
L
B
M
B
N
B
O
B
P
B
Q
B
6
B
R
B
S
B
T
B
U
B
V
B
W
B
X
B
Y
B
Z
B
2
B
3
B
4
5.5 V INPUT, 150 mA VOLTAGE REGULATOR WITH REVERSE CURRENT PROTECTION
Rev.1.3_00
S-13R1 Series
3. 3
S-13R1 Series C type
Product Name
S-13R1C12-A4T2U3
S-13R1C13-A4T2U3
S-13R1C14-A4T2U3
S-13R1C15-A4T2U3
S-13R1C16-A4T2U3
S-13R1C17-A4T2U3
S-13R1C18-A4T2U3
S-13R1C1J-A4T2U3
S-13R1C19-A4T2U3
S-13R1C20-A4T2U3
S-13R1C21-A4T2U3
S-13R1C22-A4T2U3
S-13R1C23-A4T2U3
S-13R1C24-A4T2U3
S-13R1C25-A4T2U3
S-13R1C26-A4T2U3
S-13R1C27-A4T2U3
S-13R1C28-A4T2U3
S-13R1C2J-A4T2U3
S-13R1C29-A4T2U3
S-13R1C30-A4T2U3
S-13R1C31-A4T2U3
S-13R1C32-A4T2U3
S-13R1C33-A4T2U3
S-13R1C34-A4T2U3
S-13R1C35-A4T2U3
S-13R1C36-A4T2U3
S-13R1C37-A4T2U3
S-13R1C38-A4T2U3
S-13R1C39-A4T2U3
S-13R1C40-A4T2U3
3. 4
Product Code
(1)
(2)
(3)
2
C
A
2
C
B
2
C
C
2
C
D
2
C
E
2
C
F
2
C
G
2
C
5
2
C
H
2
C
I
2
C
J
2
C
K
2
C
L
2
C
M
2
C
N
2
C
O
2
C
P
2
C
Q
2
C
6
2
C
R
2
C
S
2
C
T
2
C
U
2
C
V
2
C
W
2
C
X
2
C
Y
2
C
Z
2
C
2
2
C
3
2
C
4
S-13R1 Series D type
Product Name
S-13R1D12-A4T2U3
S-13R1D13-A4T2U3
S-13R1D14-A4T2U3
S-13R1D15-A4T2U3
S-13R1D16-A4T2U3
S-13R1D17-A4T2U3
S-13R1D18-A4T2U3
S-13R1D1J-A4T2U3
S-13R1D19-A4T2U3
S-13R1D20-A4T2U3
S-13R1D21-A4T2U3
S-13R1D22-A4T2U3
S-13R1D23-A4T2U3
S-13R1D24-A4T2U3
S-13R1D25-A4T2U3
S-13R1D26-A4T2U3
S-13R1D27-A4T2U3
S-13R1D28-A4T2U3
S-13R1D2J-A4T2U3
S-13R1D29-A4T2U3
S-13R1D30-A4T2U3
S-13R1D31-A4T2U3
S-13R1D32-A4T2U3
S-13R1D33-A4T2U3
S-13R1D34-A4T2U3
S-13R1D35-A4T2U3
S-13R1D36-A4T2U3
S-13R1D37-A4T2U3
S-13R1D38-A4T2U3
S-13R1D39-A4T2U3
S-13R1D40-A4T2U3
Product Code
(1)
(2)
(3)
2
D
A
2
D
B
2
D
C
2
D
D
2
D
E
2
D
F
2
D
G
2
D
5
2
D
H
2
D
I
2
D
J
2
D
K
2
D
L
2
D
M
2
D
N
2
D
O
2
D
P
2
D
Q
2
D
6
2
D
R
2
D
S
2
D
T
2
D
U
2
D
V
2
D
W
2
D
X
2
D
Y
2
D
Z
2
D
2
2
D
3
2
D
4
37
2.9±0.2
1.9±0.2
4
5
1
2
+0.1
0.16 -0.06
3
0.95±0.1
0.4±0.1
No. MP005-A-P-SD-1.3
TITLE
SOT235-A-PKG Dimensions
No.
MP005-A-P-SD-1.3
ANGLE
UNIT
mm
ABLIC Inc.
4.0±0.1(10 pitches:40.0±0.2)
+0.1
ø1.5 -0
+0.2
ø1.0 -0
2.0±0.05
0.25±0.1
4.0±0.1
1.4±0.2
3.2±0.2
3 2 1
4
5
Feed direction
No. MP005-A-C-SD-2.1
TITLE
SOT235-A-Carrier Tape
No.
MP005-A-C-SD-2.1
ANGLE
UNIT
mm
ABLIC Inc.
12.5max.
9.0±0.3
Enlarged drawing in the central part
ø13±0.2
(60°)
(60°)
No. MP005-A-R-SD-1.1
SOT235-A-Reel
TITLE
No.
MP005-A-R-SD-1.1
ANGLE
QTY.
UNIT
mm
ABLIC Inc.
3,000
2.0±0.2
1.3±0.2
4
3
0.05
0.3
+0.1
-0.05
+0.1
0.16 -0.06
2
1
+0.1
0.4 -0.05
No. NP004-A-P-SD-2.0
TITLE
SC82AB-A-PKG Dimensions
NP004-A-P-SD-2.0
No.
ANGLE
UNIT
mm
ABLIC Inc.
+0.1
ø1.5 -0
4.0±0.1
2.0±0.05
1.1±0.1
4.0±0.1
0.2±0.05
ø1.05±0.1
(0.7)
2.2±0.2
2
1
3
4
Feed direction
No. NP004-A-C-SD-3.0
TITLE
SC82AB-A-Carrier Tape
No.
NP004-A-C-SD-3.0
ANGLE
UNIT
mm
ABLIC Inc.
4.0±0.1
2.0±0.1
ø1.5
1.1±0.1
+0.1
-0
4.0±0.1
0.2±0.05
ø1.05±0.1
2.3±0.15
2
1
3
4
Feed direction
No. NP004-A-C-S1-2.0
TITLE
SC82AB-A-Carrier Tape
No.
NP004-A-C-S1-2.0
ANGLE
UNIT
mm
ABLIC Inc.
12.5max.
9.0±0.3
Enlarged drawing in the central part
ø13±0.2
(60°)
(60°)
No. NP004-A-R-SD-1.1
TITLE
SC82AB-A-Reel
No.
NP004-A-R-SD-1.1
QTY.
ANGLE
UNIT
mm
ABLIC Inc.
3,000
0.38±0.02
0.65
3
4
1
2
1.00±0.04
0.20±0.05
+0.05
0.08 -0.02
The heat sink of back side has different electric
potential depending on the product.
Confirm specifications of each product.
Do not use it as the function of electrode.
No. PL004-A-P-SD-1.1
TITLE
HSNT-4-B-PKG Dimensions
No.
PL004-A-P-SD-1.1
ANGLE
UNIT
mm
ABLIC Inc.
2.0±0.05
+0.1
ø1.5 -0
4.0±0.05
0.25±0.05
+0.1
1.12±0.05
2
1
3
4
ø0.5 -0
2.0±0.05
0.5±0.05
Feed direction
No. PL004-A-C-SD-2.0
TITLE
HSNT-4-B-C a r r i e r Tape
No.
PL004-A-C-SD-2.0
ANGLE
UNIT
mm
ABLIC Inc.
+1.0
9.0 - 0.0
11.4±1.0
Enlarged drawing in the central part
ø13±0.2
(60°)
(60°)
No. PL004-A-R-SD-1.0
HSNT-4-B-Reel
TITLE
PL004-A-R-SD-1.0
No.
QTY.
ANGLE
UNIT
mm
ABLIC Inc.
10,000
Land Pattern
0.30min.
0.38~0.48
0.38~0.48
0.07
0.65±0.02
(1.02)
Caution It is recommended to solder the heat sink to a board
in order to ensure the heat radiation.
PKG
Metal Mask Pattern
Aperture ratio
Aperture ratio
Caution
Mask aperture ratio of the lead mounting part is 100%.
Mask aperture ratio of the heat sink mounting part is 40%.
Mask thickness: t0.10mm to 0.12 mm
100%
40%
t0.10mm ~ 0.12 mm
TITLE
No. PL004-A-L-SD-2.0
HSNT-4-B
-Land Recommendation
PL004-A-L-SD-2.0
No.
ANGLE
UNIT
mm
ABLIC Inc.
Disclaimers (Handling Precautions)
1.
All the information described herein (product data, specifications, figures, tables, programs, algorithms and
application circuit examples, etc.) is current as of publishing date of this document and is subject to change without
notice.
2.
The circuit examples and the usages described herein are for reference only, and do not guarantee the success of
any specific mass-production design.
ABLIC Inc. is not liable for any losses, damages, claims or demands caused by the reasons other than the products
described herein (hereinafter "the products") or infringement of third-party intellectual property right and any other
right due to the use of the information described herein.
3.
ABLIC Inc. is not liable for any losses, damages, claims or demands caused by the incorrect information described
herein.
4.
Be careful to use the products within their ranges described herein. Pay special attention for use to the absolute
maximum ratings, operation voltage range and electrical characteristics, etc.
ABLIC Inc. is not liable for any losses, damages, claims or demands caused by failures and / or accidents, etc. due to
the use of the products outside their specified ranges.
5.
Before using the products, confirm their applications, and the laws and regulations of the region or country where they
are used and verify suitability, safety and other factors for the intended use.
6.
When exporting the products, comply with the Foreign Exchange and Foreign Trade Act and all other export-related
laws, and follow the required procedures.
7.
The products are strictly prohibited from using, providing or exporting for the purposes of the development of
weapons of mass destruction or military use. ABLIC Inc. is not liable for any losses, damages, claims or demands
caused by any provision or export to the person or entity who intends to develop, manufacture, use or store nuclear,
biological or chemical weapons or missiles, or use any other military purposes.
8.
The products are not designed to be used as part of any device or equipment that may affect the human body, human
life, or assets (such as medical equipment, disaster prevention systems, security systems, combustion control
systems, infrastructure control systems, vehicle equipment, traffic systems, in-vehicle equipment, aviation equipment,
aerospace equipment, and nuclear-related equipment), excluding when specified for in-vehicle use or other uses by
ABLIC, Inc. Do not apply the products to the above listed devices and equipments.
ABLIC Inc. is not liable for any losses, damages, claims or demands caused by unauthorized or unspecified use of
the products.
9.
In general, semiconductor products may fail or malfunction with some probability. The user of the products should
therefore take responsibility to give thorough consideration to safety design including redundancy, fire spread
prevention measures, and malfunction prevention to prevent accidents causing injury or death, fires and social
damage, etc. that may ensue from the products' failure or malfunction.
The entire system in which the products are used must be sufficiently evaluated and judged whether the products are
allowed to apply for the system on customer's own responsibility.
10. The products are not designed to be radiation-proof. The necessary radiation measures should be taken in the
product design by the customer depending on the intended use.
11. The products do not affect human health under normal use. However, they contain chemical substances and heavy
metals and should therefore not be put in the mouth. The fracture surfaces of wafers and chips may be sharp. Be
careful when handling these with the bare hands to prevent injuries, etc.
12. When disposing of the products, comply with the laws and ordinances of the country or region where they are used.
13. The information described herein contains copyright information and know-how of ABLIC Inc. The information
described herein does not convey any license under any intellectual property rights or any other rights belonging to
ABLIC Inc. or a third party. Reproduction or copying of the information from this document or any part of this
document described herein for the purpose of disclosing it to a third-party is strictly prohibited without the express
permission of ABLIC Inc.
14. For more details on the information described herein or any other questions, please contact ABLIC Inc.'s sales
representative.
15. This Disclaimers have been delivered in a text using the Japanese language, which text, despite any translations into
the English language and the Chinese language, shall be controlling.
2.4-2019.07
www.ablic.com
工商网监
湘ICP备2023018690号
