S-24CM01C
2-WIRE SERIAL E2PROM
www.ablic.com
www.ablicinc.com
Rev.2.0_03_S
© ABLIC Inc., 2010-2013
The S-24CM01C is a 2-wire, low current consumption and wide range operation serial E2PROM. The S-24CM01C has the
capacity of 1 M-bit, and the organization is 131072 words 8-bit. Page write and sequential read are available.
Features
Operating voltage range
Page write:
Sequential read
Operation frequency:
Read:
1.6 V to 5.5 V
Write:
1.7 V to 5.5 V
256 bytes / page
1.0 MHz (VCC = 2.5 V to 5.5 V)
400 kHz (VCC = 1.6 V to 2.5 V)
Write time:
5.0 ms max.
Noise suppression:
Schmitt trigger and noise filter on input pins (SCL, SDA)
Write protect function during the low power supply voltage
Endurance:
106cycles / unit*1 (Ta = 25°C)
Data retention:
100 years (Ta = 25°C)
Memory capacity:
1 M-bit
Write protect:
100%
Initial shipment data:
FFh
Lead-free (Sn 100%), halogen-free*2
*1. For each unit (unit: the 4 bytes with the same address of P0, W15 to W2)
*2. Refer to “ Product Name Structure” for details.
Package
8-Pin SOP (JEDEC)
Caution
This product is intended to use in general electronic devices such as consumer electronics,
office equipment, and communications devices. Before using the product in medical equipment
or automobile equipment including car audio, keyless entry and engine control unit, contact to
ABLIC Inc. is indispensable.
1
2-WIRE SERIAL E2PROM
S-24CM01C
Rev.2.0_03_S
Pin Configuration
1. 8-Pin SOP (JEDEC)
8-Pin SOP (JEDEC)
Top view
Table 1
Pin No
1
8
2
7
3
6
4
5
Figure 1
S-24CM01CI-J8T1U4
1
2
3
4
5
6
Description
No connection
Slave address input
Slave address input
Ground
Serial data I/O
Serial clock input
Write protect input
7
WP
Connected to VCC:
Protection valid
Open or connected to GND: Protection invalid
8
VCC
Power supply
*1. Connect to GND or VCC.
*2. Do not use it in high impedance.
Remark Refer to the “Package drawings” for the details.
2
Symbol
NC*1
A1
A2
GND
SDA*2
SCL*2
2-WIRE SERIAL E2PROM
S-24CM01C
Rev.2.0_03_S
Block Diagram
VCC
WP
SCL
GND
Start / Stop
Detector
SDA
Voltage Detector
Serial Clock
Controller
High-Voltage Generator
LOAD
Device Address
Comparator
COMP
Data Register
LOAD INC
A2
R/W
A1
Address
Counter
Y Decoder
X Decoder
Memory Cell Array
Selector
Data Output
ACK Output
Controller
DIN
DOUT
Figure 2
3
2-WIRE SERIAL E2PROM
S-24CM01C
Rev.2.0_03_S
Absolute Maximum Ratings
Table 2
Item
Symbol
Absolute Maximum Ratings
Unit
Power supply voltage
VCC
0.3 to 6.5
V
Input voltage
VIN
0.3 to 6.5
V
Output voltage
VOUT
0.3 to 6.5
V
Operation ambient temperature
Topr
40 to 85
°C
Storage temperature
Tstg
65 to 150
°C
Caution The absolute maximum ratings are rated values exceeding which the product could suffer
physical damage. These values must therefore not be exceeded under any conditions.
Recommended Operating Conditions
Table 3
Item
Symbol
Power supply voltage
VCC
High level input voltage
VIH
Low level input voltage
VIL
Condition
Read Operation
Write Operation
VCC = 1.8 V to 5.5 V
VCC = 1.6 V to 1.8 V
VCC = 1.8 V to 5.5 V
VCC = 1.6 V to 1.8 V
Ta = 40°C to 85°C
Min.
Max.
1.6
1.7
5.5
5.5
0.7 VCC
0.8 VCC
0.3
0.3
5.5
5.5
0.3 VCC
0.2 VCC
Unit
V
V
V
V
V
V
Pin Capacitance
Table 4
Item
Input capacitance
I/O capacitance
Symbol
CIN
CI / O
Condition
VIN = 0 V (SCL, A1, A2, WP)
VI / O = 0 V (SDA)
(Ta = 25°C, f = 1.0 MHz, VCC = 5.0 V)
Min.
Max.
Unit
10
pF
10
pF
Endurance
Table 5
Item
Symbol
Operation Ambient Temperature
Min.
Endurance
NW
Ta = 25°C
106
*1. For each unit (unit: the 4 bytes with the same address of P0, W15 to W2)
Max.
Unit
cycles / unit*1
Max.
Unit
year
Data Retention
Table 6
Item
Data retention
4
Symbol
Operation Ambient Temperature
Ta = 25°C
Min.
100
2-WIRE SERIAL E2PROM
S-24CM01C
Rev.2.0_03_S
DC Electrical Characteristics
Table 7
Item
Symbol
Current consumption (READ)
ICC1
Condition
Ta = 40°C to 85°C
VCC = 2.5 V to 5.5 V
VCC = 1.6 V to 2.5 V
fSCL = 1.0 MHz
fSCL = 400 kHz
Min.
Max.
Min.
Max.
2.0
1.5
Unit
mA
Table 8
Item
Symbol
Current consumption (WRITE)
ICC2
Condition
Ta = 40°C to 85°C
VCC = 2.5 V to 5.5 V
VCC = 1.7 V to 2.5 V
fSCL = 1.0 MHz
fSCL = 400 kHz
Min.
Max.
Min.
Max.
4.0
4.0
Unit
mA
Table 9
Ta = 40°C to 85°C
Item
Symbol
Standby current consumption ISB
Input leakage current 1
ILI1
Input leakage current 2
ILI2
Output leakage current
ILO
Input current 1
IIL
Input current 2
IIH
Input Impedance 1
ZIL
Input Impedance 2
ZIH
Low level output voltage
VOL
Condition
VIN = VCC or GND
SCL, SDA,
VIN = GND to VCC
A1, A2
VIN > 0.7 VCC
At standby mode
SDA
VOUT = GND to VCC
WP
VIN < 0.3 VCC
WP
VIN > 0.7 VCC
WP
VIN = 0.3 VCC
WP
VIN = 0.7 VCC
IOL = 3.2 mA
IOL = 1.5 mA
IOL = 0.7 mA
VCC = 2.5 V to 5.5 V
VCC = 1.6 V to 2.5 V
Unit
Min.
Max.
Min.
Max.
10.0
4.0
A
1.0
1.0
A
1.0
1.0
A
1.0
1.0
A
50.0
50.0
A
2.0
2.0
A
30
30
k
500
500
k
0.4
0.3
0.2
0.3
0.2
V
V
V
5
2-WIRE SERIAL E2PROM
S-24CM01C
Rev.2.0_03_S
AC Electrical Characteristics
Table 10 Measurement Conditions
Input pulse voltage
Input pulse rising / falling time
Output reference voltage
Output load
Input pulse voltage
0.2 VCC to 0.8 VCC
20 ns or less
0.3 VCC to 0.7 VCC
100 pF
Output reference voltage
0.8 VCC
0.7 VCC
0.3 VCC
0.2 VCC
Figure 3 I/O Waveform during AC Measurement
Table 11
Item
Symbol
SCL clock frequency
SCL clock time “L”
SCL clock time “H”
SDA output delay time
SDA output hold time
Start condition setup time
Start condition hold time
Data input setup time
Data input hold time
Stop condition setup time
SCL, SDA rising time
SCL, SDA falling time
WP setup time
WP hold time
WP release setup time
WP release hold time
Bus release time
Noise suppression time
fSCL
tLOW
tHIGH
tAA
tDH
tSU.STA
tHD.STA
tSU.DAT
tHD.DAT
tSU.STO
tR
tF
tWS1
tWH1
tWS2
tWH2
tBUF
tI
Ta = 40°C to 85°C
VCC = 2.5 V to 5.5 V
VCC = 1.6 V to 2.5 V
Min.
Max.
Min.
Max.
0
1000
0
400
0.4
1.3
0.3
0.6
0.1
0.5
0.1
0.9
50
50
0.25
0.6
0.25
0.6
80
100
0
0
0.25
0.6
0.3
0.3
0.3
0.3
0
0
0
0
0
0
0
0
0.5
1.3
50
50
tHIGH
tF
tLOW
Unit
kHz
s
s
s
ns
s
s
ns
ns
s
s
s
s
s
s
s
s
ns
tR
SCL
tHD.STA
tHD.DAT
tSU.STA
tSU.DAT
tSU.STO
SDA
(input)
tAA
tDH
SDA
(output)
Figure 4 Bus Timing
6
tBUF
2-WIRE SERIAL E2PROM
S-24CM01C
Rev.2.0_03_S
Table 12
Item
Symbol
Write time
Start Condition
tWR
Ta = 40°C to 85°C
VCC = 1.7 V to 5.5 V
Min.
Max.
5.0
Acknowledgment
Signal
Write data
Stop Condition
Unit
ms
tWR
Start Condition
SCL
D0
SDA
tWS1
tWH1
tWS2
tWH2
WP
(valid)
WP
(invalid)
Figure 5 Write Cycle Timing
7
2-WIRE SERIAL E2PROM
S-24CM01C
Rev.2.0_03_S
Pin Functions
1. A1 and A2 (Slave address input) pins
In the S-24CM01C, to set the slave address, connect each pin of A1, A2 to GND or VCC. Therefore the users can set
4 types of slave address by a combination of A1, A2 pins.
Comparing the slave address transmitted from the master device and one that you set, makes possible to select the
S-24CM01C from other devices connected onto the bus.
Each A1 and A2 pin has a pull-down resistor. In open, these pins have the status when they are connected to GND.
2. SDA (Serial data input / output) pin
The SDA pin is used for the bi-directional transmission of serial data. This pin is a signal input pin, and an Nch open
drain output pin.
In use, generally, connect the SDA line to any other device which has the open-drain or open-collector output with
Wired-OR connection by pulling up to VCC by a resistor (Figure 6 shows the relation with an output load).
3. SCL (Serial clock input) pin
The SCL pin is used for the serial clock input. Since the signals are processed at a rising or falling edge of the SCL
clock, pay attention to the rising and falling time and comply with the specification.
4. WP (Write protect input) pin
The write protect is enabled by connecting the WP pin to VCC. When not using the write protect, connect this pin to
GND or set in open.
Maximum value of pull-up resistor
[k]
20
18
16
14
12
10
8
6
4
2
0
fSCL= 400 kHz
fSCL= 1000 kHz
10
100
Value of load capacity
[pF]
Figure 6 Output Load
Initial Shipment Data
Initial shipment data of all addresses is “FFh”.
8
200
2-WIRE SERIAL E2PROM
S-24CM01C
Rev.2.0_03_S
ECC Function (Error correction function)
S-24CM01C Series adds 6 ECC bits for error correction to each 4 bytes with the same address of P0, W15 to W2. The
ECC function can make correction and output correct data even if wrong data of 1 bit is in the 4 bytes when reading.
In addition, the S-24CM01C Series rewrites the 4 bytes used as the rewriting minimum unit and 6 ECC bits if only 1 byte
data is input.
Therefore, it is recommended to rewrite data of each 4 bytes with the same address of P0, W15 to W2 in order to get the
maximum endurance in the application in which the data is rewritten frequently.
Operation
1. Start condition
Start is identified by a high to low transition of the SDA line while the SCL line is stable at high.
Every operation begins from a start condition.
2. Stop condition
Stop is identified by a low to high transition of the SDA line while the SCL line is stable at high.
When a device receives a stop condition during a read sequence, the read operation is interrupted, and the device
enters standby mode.
When a device receives a stop condition during a write sequence, the reception of the write data is halted, and the S24CM01C initiates a write cycle.
tSU.STA
tHD.STA
tSU.STO
SCL
SDA
Start Condition
Stop Condition
Figure 7 Start / Stop Conditions
9
2-WIRE SERIAL E2PROM
S-24CM01C
Rev.2.0_03_S
3. Data transmission
Changing the SDA line while the SCL line is low, data is transmitted.
Changing the SDA line while the SCL line is high, a start or stop condition is recognized.
tSU.DAT
tHD.DAT
SCL
SDA
Figure 8 Data Transmission Timing
4. Acknowledge
The unit of data transmission is 8 bits. During the 9th clock cycle period the receiver on the bus pulls down the SDA
line to acknowledge the receipt of the 8-bit data.
When an internal write cycle is in progress, the S-24CM01C does not generate an acknowledge.
SCL
(E2PROM Input)
1
8
9
SDA
(Master Output)
Acknowledge
Output
SDA
(E PROM Output)
2
Start Condition
tAA
Figure 9 Acknowledge Output Timing
10
tDH
2-WIRE SERIAL E2PROM
S-24CM01C
Rev.2.0_03_S
5. Device addressing
To start communication, the master device on the system sends a start condition to the bus line. Next, the master
device sends a 7-bit device address and a 1-bit read / write instruction code to the SDA bus.
The upper 4 bits of the device address are the “Device Code”, and are fixed to “1010”.
In the S-24CM01C, 2 bits with successive values are called the “Slave Address”. These bits are used to identify a
device on the system bus and are compared with a predetermined value defined by the address input pins (A2 and
A1). If the comparison result is a match, the slave device responds with an acknowlede during the 9th clock cycle.
The bit that follows the slave address (P0) is the "Page Address". This bit is used to select one of two 64 K-byte
memory blocks (addresses 00000h to 0FFFFh, and addresses 10000h to 1FFFFh).
Slave / Page
Address
Device Code
1
0
1
0
A2
A1
MSB
P0
R/W
LSB
Figure 10 Device Address
11
2-WIRE SERIAL E2PROM
S-24CM01C
Rev.2.0_03_S
6. Write
6. 1 Byte write
When the master sends a 7-bit device address and a 1-bit read / write instruction code set to “0” following a start
condition, the S-24CM01C acknowledges it. The S-24CM01C then receives the upper 8-bit word address and
responds with an acknowledge. The S-24CM01C then receives the lower 8-bit word address and responds with
an acknowledge. After the S-24CM01C receives 8-bit write data and responds with an acknowledge, it receives a
stop condition and that initiates the write cycle at the addressed memory.
During the write cycle, all operations are forbidden and no acknowledge is generated.
S
T
A
R
T
SDA LINE
DEVICE
ADDRESS
W
R
I
T
E
1 0 1 0 A2 A1 P0 0
M
S
B
UPPER WORD
ADDRESS
W15 W14 W13 W12 W11 W10 W9 W8
L R A
S / C
B W K
LOWER WORD
ADDRESS
DATA
W7 W6 W5 W4 W3 W2 W1 W0
D7 D6 D5 D4 D3 D2 D1 D0
A
C
K
Figure 11 Byte Write
12
A
C
K
S
T
O
P
A
C
K
2-WIRE SERIAL E2PROM
S-24CM01C
Rev.2.0_03_S
6. 2 Page write
The page write mode allows up to 256 bytes to be written in a single write operation in the S-24CM01C.
The basic process used to transmit data is the same as byte write, but page write involves sequentially receiving
as much 8-bit write data as the size of the page.
When the S-24CM01C receives a 7-bit device address and a 1-bit read / write instruction code set to “0” following
a start condition, it generates an acknowledge. The S-24CM01C then receives the upper 8-bit word address, and
responds with an acknowledge. The S-24CM01C then receives the lower 8-bit word address, and responds with
an acknowledge. After the S-24CM01C receives 8-bit write data and responds with an acknowledge, it receives 8bit write data corresponding to the next word address, and generates an acknowledge. The S-24CM01C repeats
reception of 8-bit write data and generation of acknowledges in succession. The S-24CM01C can receive as
much write data as the maximum page size.
Receiving a stop condition initiates a write cycle of the area starting from the designated memory address and
with a page size equal to the received write data.
W
R
I
T
E
UPPER
WORD ADDRESS (n)
1 0 1 0 A2 A1 P0 0
W15 W14 W13 W12 W11 W10 W9 W8
S
T
A
R
T
SDA LINE
DEVICE
ADDRESS
M
S
B
L R A
S / C
B W K
LOWER
WORD ADDRESS (n)
DATA (n)
W7 W6 W5 W4 W3 W2 W1 W0
A
C
K
D7
S
T
O
P
DATA (n+x)
D0
D7
D0
A
C
K
Figure 12 Page Write
In the S-24CM01C, the lower 8 bits of the word address are automatically incremented every time the
S-24CM01C receives 8-bit write data. If the size of the write data exceeds 256 bytes, the upper 8 bits of the word
address and the page address (P0) remain unchanged, and the lower 8 bits are rolled over so that the last
256-byte data that the S-24CM01C received is overwritten.
13
2-WIRE SERIAL E2PROM
S-24CM01C
Rev.2.0_03_S
6. 3 Write protect
Write protect is available in the S-24CM01C. When the WP pin is connected to the VCC, write operation to memory
area is inhibited.
When the WP pin is connected to GND or set in open, the write protect is invalid, and write operation in all
memory area is available.
Fix the level of the WP pin from start condition in the write operation (byte write, page write) until stop condition. If
the WP pin changes during this time, the address data being written at this time is not guaranteed. Regarding the
timing of write protect, refer to Figure 5.
In not using the write protect, connect the WP pin to GND or set it open. The write protect is valid in the range of
operation power supply voltage.
As seen in Figure 13 when the write protect is valid, the S-24CM01C does not generate an acknowledgment
signal after data input.
S
T
A
R
T
SDA LINE
DEVICE
ADDRESS
W
R
I
T
E
1 0 1 0 A2 A1 P0 0
M
S
B
UPPER
WORD ADDRESS
W15 W14 W13 W12 W11 W10 W9 W8
L R A
S / C
B W K
LOWER WORD
ADDRESS
DATA
W7 W6 W5 W4 W3 W2 W1 W0
D7 D6 D5 D4 D3 D2 D1 D0
A
C
K
WP
Figure 13 Write Protect
14
A
C
K
S
T
O
P
N
A
C
K
2-WIRE SERIAL E2PROM
S-24CM01C
Rev.2.0_03_S
6. 4 Acknowledge polling
Acknowledge polling is used to know the completion of the write cycle in the S-24CM01C.
After the S-24CM01C receives a stop condition and once the write cycle starts, all operations are inhibited and no
response is made to the signal transmitted by the master device.
Accordingly the master device can recognize the completion of the write cycle in the S-24CM01C by detecting a
response from the slave device after transmitting the start condition, the device address and the read / write
instruction code to the S-24CM01C (slave device).
That is, if the S-24CM01C does not generate an acknowledgment signal, the write cycle is in progress and if the
S-24CM01C generates an acknowledgment signal, the write cycle has been completed.
It is recommended to use the read instruction “1” as the read / write instruction code transmitted by the master
device.
Acknowledge polling during write
DATA
SDA
LINE
D2 D1 D0
S
T
O
P
W
R
I
T
E
S
T
A
R
T
S
T
A
R
T
DEVICE
ADDRESS 0
W
R
I
T
E
DEVICE
ADDRESS 0
R N
/ A
W C
K
WORD
ADDRESS
A
C
K
R A
/ C
WK
tWR
Acknowledge polling during read
S
S
T
T
A
O
R
P
DATA
T
SDA
DEVICE
D2 D1 D0
ADDRESS
LINE
R
E
A
D
1
R N
/ A
W C
K
S
T
A
R
T
NO ACK from
R Master Device
E
A
D
DEVICE
ADDRESS 1
DATA
R A
/ C
WK
S
T
O
P
S
T
A
R
T
DEVICE
ADDRESS
R A
/ C
WK
tWR
Remark
Users are able to input word address and data after ACK output in acknowledge polling during write.
Users are able to read data after ACK output in acknowledge polling during read. However, after that users input
the write instruction, a start condition may not be input during data output. Input a stop condition and the next
instruction after data output and ACK output.
Figure 14 Usage Example of Acknowledge Polling
15
2-WIRE SERIAL E2PROM
S-24CM01C
Rev.2.0_03_S
7. Read
7. 1 Current address read
Either in writing or in reading, the S-24CM01C holds the last accessed memory address. The memory address is
maintained as long as the power voltage does not decrease less than the operating voltage.
The master device can read the data at the memory address of the current address pointer without assigning the
word address as a result, when it recognizes the position of the address pointer in the S-24CM01C. This is called
“Current Address Read”.
In the following, the address counter in the S-24CM01C is assumed to be “n”.
When the S-24CM01C receives a 7-bit device address and a 1-bit read / write instruction code set to “1” following
a start condition, it responds with an acknowledge.
Next, an 8-bit data at the address “n” is sent from the S-24CM01C synchronous to the SCL clock. The address
counter is incremented and the content of the address counter becomes n 1.
The master device outputs stop condition not an acknowledge, the reading of S-24CM01C is ended.
S
T
A
R
T
SDA LINE
DEVICE
ADDRESS
R
E
A
D
1 0 1 0 A2 A1 X 1
M
S
B
NO ACK from
Master Device
S
T
O
P
D7 D6 D5 D4 D3 D2 D1 D0
L R A
S / C
B W K
DATA
Figure 15 Current Address Read
Attention should be paid to the following point on the recognition of the address pointer in the S-24CM01C.
When reading, the memory address counter in the S-24CM01C is automatically incremented after the 8th bit of
data is output. When writing, on the other hand, the upper bits of the memory address (the upper bits of the word
address and the page address*1) are left unchanged and are not incremented.
16
1. The upper 8 bits of the word address and the page address (P0)
2-WIRE SERIAL E2PROM
S-24CM01C
Rev.2.0_03_S
7. 2 Random read
Random read is used to read the data at an arbitrary memory address.
A dummy write is performed to load the memory address into the address counter.
When the S-24CM01C receives a 7-bit device address and a 1-bit read / write instruction code set to “0” following
a start condition, it responds with an acknowledge.
The S-24CM01C then receives a upper 8-bit word address and responds with an acknowledge. And the
S-24CM01C receives a lower 8-bit word address and responds with an acknowledge. The memory address is
loaded to the address counter in the S-24CM01C by these operations. Reception of write data does not follow in a
dummy write whereas reception of write data follows in byte write and in page write.
Since the memory address is loaded into the memory address counter by dummy write, the master device can
read the data starting from the arbitrary memory address by transmitting a new start condition and performing the
same operation in the current address read.
That is, when the S-24CM01C receives a 7-bit device address and a 1-bit read / write instruction code set to “1”,
following a start condition signal, it responds with an acknowledge. Next, 8-bit data is transmitted from the
S-24CM01C in synchronous to the SCL clock. The master device outputs stop condition not an acknowledge, the
reading of S-24CM01C is ended.
S
T
A
R
T
SDA
LINE
DEVICE
ADDRESS
W
R
I
T
E
1 0 1 0 A2 A1 P0 0
M
S
B
UPPER
WORD ADDRESS
LOWER
WORD ADDRESS
W15
X W14 W13W12W11W10 W9W8
W7 W6 W5 W4 W3 W2 W1 W0
L R A
S / C
B W K
A
C
K
S
T
A
R
T
DEVICE
ADDRESS
R
E
A
D
1 0 1 0 A2 A1 X 1
A
C
K
M
S
B
NO ACK from
Master Device
DATA
下図へ続く
D7 D6
D5 D4 D3 D2 D1 D0
L R A
S / C
B W K
DUMMY WRITE
Figure 16 Random Read
17
S
T
O
P
2-WIRE SERIAL E2PROM
S-24CM01C
Rev.2.0_03_S
7. 3 Sequential read
When the S-24CM01C receives a 7-bit device address and a 1-bit read / write instruction code set to “1” following
a start condition both in current address read and random read, it responds with an acknowledge.
When an 8-bit data is output from the S-24CM01C synchronous to the SCL clock, the address counter is
automatically incremented.
When the master device responds with an acknowledge, the data at the next memory address is transmitted.
Response with an acknowledge by the master device has the memory address counter in the S-24CM01C
incremented and makes it possible to read data in succession. This is called “Sequential Read”.
The master device outputs stop condition not an acknowledge, the reading of S-24CM01C is ended.
Data can be read in succession in the sequential read mode. When the memory address counter reaches the last
word address, it rolls over to the first word address.
DEVICE
ADDRESS
SDA
LINE
NO ACK from
Master Device
R
E
A
D
1
R A
/ C
W K
A
C
K
D7
D0
DATA (n)
A
C
K
D7
D0
D7
DATA (n+1)
Figure 17 Sequential Read
18
S
T
O
P
A
C
K
D0
DATA (n+2)
D7
D0
DATA (n+x)
2-WIRE SERIAL E2PROM
S-24CM01C
Rev.2.0_03_S
Write Protect Function during the Low Power Supply Voltage
The S-24CM01C has a built-in detection circuit which operates with the low power supply voltage, cancels Write when the
power supply voltage drops and power-on. Its detection and release voltages are 1.50 V typ. (Refer to Figure 18).
The S-24CM01C cancels Write by detecting a low power supply voltage when it receives a stop condition.
In the data trasmission and the Write operation, data in the address written during the low power supply voltage is not
assurable.
Power Supply Voltage
Detection Voltage (VDET)
1.50 V typ.
Release Voltage (VDET)
1.50 V typ.
Write Instruction cancel
Figure 18 Operation during Low Power Supply Voltage
19
2-WIRE SERIAL E2PROM
S-24CM01C
Rev.2.0_03_S
Using S-24CM01C
1. Adding a pull-up resistor to SDA I/O pin and SCL input pin
In consideration of I2C-bus protocol function, the SDA I/O pins should be connected with a pull-up resistor.
The S-24CM01C cannot transmit normally without using a pull-up resistor.
In case that the SCL input pin of the S-24CM01C is connected to the Nch open drain output pin of the master device,
connect the SCL pin with a pull-up resistor. As well, in case the SCL input pin of the S-24CM01C is connected to the
tri-state output pin of the master device, connect the SCL pin with a pull-up resistor in order not to set it in high
impedance. This prevents the S-24CM01C from error caused by an uncertain output (high impedance) from the
tri-state pin when resetting the master device during the voltage drop.
2. Equivalent circuit of input and I/O pin
The S-24CM01C does not have a built-in pull-down or pull-up resistor for the SCL and SDA pins. The WP, A2, and
A1 pins have a pull-down resistor. The SDA pin has an open-drain output. The following are equivalent circuits of the
pins.
SCL
Figure 19 SCL Pin
SDA
Figure 20 SDA Pin
20
2-WIRE SERIAL E2PROM
S-24CM01C
Rev.2.0_03_S
WP
Figure 21 WP Pin
A1, A2
Figure 22 A1, A2 Pins
21
2-WIRE SERIAL E2PROM
S-24CM01C
Rev.2.0_03_S
3. Phase adjustment during S-24CM01C access
The S-24CM01C does not have a pin to reset (the internal circuit). The users cannot forcibly reset it externally. If the
communication to the S-24CM01C interrupted, the users need to handle it as you do for software.
In the S-24CM01C, users are able to reset the internal circuit by inputting a start condition and a stop condition.
Although the reset signal is input to the master device, the S-24CM01C’s internal circuit does not go in reset, but it
does by inputting a stop condition to the S-24CM01C. The S-24CM01C keeps the same status thus cannot do the
next operation. Especially, this case corresponds to that only the master device is reset when the power supply
voltage drops.
If the power supply voltage restored in this status, input the instruction after resetting (adjusting the phase with the
master device) the S-24CM01C. How to reset is shown below.
[How to reset S-24CM01C]
The S-24CM01C is able to be reset by a start and stop instructions. When the S-24CM01C is reading data “0” or is
outputting the acknowledgment signal, outputs “0” to the SDA line. In this status, the master device cannot output
an instruction to the SDA line. In this case, terminate the acknowledgment output operation or the Read operation,
and then input a start instruction. Figure 23 shows this procedure.
First, input a start condition. Then transmit 9 clocks (dummy clock) of SCL. During this time, the master device sets
the SDA line to “H”. By this operation, the S-24CM01C interrupts the acknowledgment output operation or data
output, so input a start condition*1. When a start condition is input, the S-24CM01C is reset. To make doubly sure,
input the stop condition to the S-24CM01C. The normal operation is then possible.
Start
Condition
Start
Condition
Dummy Clock
1
2
8
Stop
Condition
9
SCL
SDA
Figure 23 Resetting S-24CM01C
*1. After 9 clocks (dummy clock), if the SCL clock continues to being output without inputting a start condition,
S-24CM01C may go in the write operation when it receives a stop condition. To prevent this, input a start
condition after 9 clocks (dummy clock).
Remark
22
Regarding this reset procedure with dummy clock, it is recommended to perform at the system
initialization after applying the power supply voltage.
2-WIRE SERIAL E2PROM
S-24CM01C
Rev.2.0_03_S
4. Acknowledge check
The I2C-bus protocol includes an acknowledge check function as a handshake function to prevent a communication
error. This function allows detection of a communication failure during data communication between the master
device and S-24CM01C. This function is effective to prevent malfunction, so it is recommended to perform an
acknowledge check with the master device.
5. Built-in power-on-clear circuit
The S-24CM01C has a built-in power-on-clear circuit that initializes itself at the same time during power-on.
Unsuccessful initialization may cause a malfunction. To operate the power-on-clear circuit normally, the following
conditions must be satisfied to raise the power supply voltage.
5. 1 Raising power supply voltage
Shown in Figure 24, raise the power supply voltage from 0.2 V max., within the time defined as tRISE which is the
time required to reach the power supply voltage to be set.
For example, if the power supply voltage is 5.0 V, tRISE = 200 ms seen in Figure 25. The power supply voltage
must be raised within 200 ms.
tRISE max.
Power Supply Voltage (VCC)
VINIT max.
0.2 V
0V
*1
*2
tINIT max.
*1. 0 V means there is no difference in potential between the VCC pin and the GND pin of the S-24CM01C.
*2. tINIT is the time required to initialize the S-24CM01C. No instructions are accepted during this time.
Figure 24 Raising Power Supply Voltage
23
2-WIRE SERIAL E2PROM
S-24CM01C
Rev.2.0_03_S
5.0
4.0
Power Supply Voltage (VCC)
[V]
3.0
2.0
50
100
150
200
Power Supply Voltage Rise Time (tRISE) max.
[ms]
For example: If the power supply voltage = 5.0 V, raise the power supply voltage to 5.0 V within 200 ms.
Figure 25 Power Supply Voltage Rise Time
When initialization is successfully completed by the power-on-clear circuit, the S-24CM01C enters the standby
status.
If the power-on-clear circuit does not operate;
The S-24CM01C has not completed initialization, an instruction previously input is still valid or an instruction may
be inappropriately recognized. In this case, S-24CM01C may perform the Write operation.
The voltage drops due to power off while the S-24CM01C is being accessed. Even if the master device is reset
due to the low power voltage, the S-24CM01C may malfunction unless the power-on-clear operation conditions of
S-24CM01C are satisfied.
When not keeping to the power supply voltage rise time seen in Figure 25, adjust the phase (reset) to reset the
internal circuit in the S-24CM01C normally.
24
2-WIRE SERIAL E2PROM
S-24CM01C
Rev.2.0_03_S
5. 2 Initialization time
The S-24CM01C initializes at the same time when the power supply voltage is raised. Input instructions to the
S-24CM01C after initialization. S-24CM01C does not accept any instruction during initialization.
Figure 26 shows the initialization time of the S-24CM01C.
100 m
10 m
Initialization Time
(tINIT) max.
[s]
1.0 m
100
10
1.0
1.0
10 100 1.0 m 10 m 100 m
Power Supply voltage Rise Time (tRISE)
[s]
Figure 26 Initialization Time of S-24CM01C
25
2-WIRE SERIAL E2PROM
S-24CM01C
Rev.2.0_03_S
6. Data hold time (tHD.DAT = 0 ns)
If SCL and SDA of the S-24CM01C are changed at the same time, it is necessary to prevent a start / stop condition
from being mistakenly recognized due to the effect of noise.
The S-24CM01C may error if it does not recognize a start / stop condition correctly during transmission.
It is recommended to set the delay time of 0.3 s minimum from a falling edge of SCL for the SDA.
This is to prevent S-24CM01C from going in a start / stop condition due to the time lag caused by the load of the bus
line.
tHD.DAT = 0.3 s min.
SCL
SDA
Figure 27 S-24CM01C Data Hold Time
7. SDA pin and SCL pin noise suppression time
The S-24CM01C includes a built-in low-pass filter at the SDA and SCL pins to suppress noise. This means that if the
power supply voltage is 5.0 V, noise with a pulse width of 90 ns or less can be suppressed.
For details of the assurable value, refer to noise suppression time (tl) in Table 11.
300
Noise Suppression Time (tI) max.
[ns]
200
100
1
2
3
4
5
Power supply voltage (VCC)
[V]
Figure 28 Noise Suppression Time for SDA and SCL Pins
26
2-WIRE SERIAL E2PROM
S-24CM01C
Rev.2.0_03_S
8. Operation when input stop condition during input write data
The S-24CM01C does the write operation only when it receives data of 1 byte or more and receives a stop condition
immediately after ACK output.
Refer to Figure 29 regarding details.
Write Enable
by stop condition
Write Inhibition
by stop condition
S
T
A
R
T
SDA
LINE
DEVICE
ADDRESS
W
R
I
T
E
1 0 1 0 A2 A1 P0 0
M
S
B
LOWER
WORD ADDRESS (n)
UPPER
WORD ADDRESS (n)
W15
L R A
S / C
BWK
W7
W8
A
C
K
Write Inhibition
by stop condition
D7 D6 D5 D4 D3 D2 D1 D0
A
C
K
D7
Write Enable
by stop condition
Write Inhibition
by stop condition
DATA (n+1)
DATA (n)
W0
Write Enable
by stop condition
S
T
O
P
DATA (n+x)
D0
A
C
K
D7
A
C
K
D0
A
C
K
Figure 29 Write Operation by Inputting Stop Condition during Write
9. Command cancel by start condition
By a start condition, users are able to cancel command which is being input. However, adjust the phase while the
S-24CM01C is outputting “L” because users are not able to input a start condition. When users cancel the command,
there may be a case that the address will not be identified. Use random read for the read operation, not current
address read.
10. Precaution for use
Do not operate these ICs in excess of the absolute maximum ratings. Attention should be paid to the power supply
voltage, especially. The surge voltage which exceeds the maximum absolute ratings can cause latch-up and
malfunction. Perform operations after confirming the detailed operation condition in the data sheet.
Operations with moisture on the S-24CM01C pins may cause malfunction by short-circuit between pins. Especially, in
occasions like picking the S-24CM01C up from low temperature tank during the evaluation. Be sure that not remain
frost on the S-24CM01C’s pins to prevent malfunction by short-circuit.
Also attention should be paid in using on environment, which is easy to dew for the same reason.
27
2-WIRE SERIAL E2PROM
S-24CM01C
Rev.2.0_03_S
Precautions
● Insert a bypass capacitor of about 0.1 F between the VCC and GND pins for stabilization.
● Do not apply an electrostatic charge to this IC that exceeds the performance ratings of the built-in electrostatic
protection circuit.
● ABLIC Inc. claims no responsibility for any and all disputes arising out of or in connection with any infringement of the
products including this IC upon patents owned by a third party.
Product Name Structure
1. Product name
S-24CM01C
I
J8T1
U
4
Environmental code
U:
Lead-free (Sn 100%), halogen-free
Package name (abbreviation) and IC packing specification
J8T1: 8-Pin SOP (JEDEC), Tape
Fixed
Product name
S-24CM01C: 1 M-bit
2. Package
Package name
8-Pin SOP (JEDEC)
28
Package
FJ008-Z-P-SD
Drawing code
Tape
FJ008-Z-C-SD
Reel
FJ008-Z-R-SD
+0.20
5.02 -0.35
8
5
1
4
1.27
0.20±0.05
+0.11
0.4 -0.07
No. FJ008-Z-P-SD-2.1
TITLE
SOP8J-Z-PKG Dimensions
FJ008-Z-P-SD-2.1
No.
ANGLE
UNIT
mm
ABLIC Inc.
4.0±0.1(10 pitches:40.0±0.2)
2.0±0.05
ø1.55±0.05
0.3±0.05
ø1.5 min.
8.0±0.1
2.1±0.1
+0.30
6.5 -0.25
1
8
4
5
Feed direction
No. FJ008-Z-C-SD-1.0
TITLE
SOP8J-Z-Carrier Tape
No.
FJ008-Z-C-SD-1.0
ANGLE
UNIT
mm
ABLIC Inc.
17.5±1.5
13.4±1.0
Enlarged drawing in the central part
ø21±0.8
2±0.5
ø13±0.2
No. FJ008-Z-R-SD-1.0
TITLE
SOP8J-Z-Reel
No.
FJ008-Z-R-SD-1.0
QTY.
ANGLE
UNIT
mm
ABLIC Inc.
4,000
Disclaimers (Handling Precautions)
1.
All the information described herein (product data, specifications, figures, tables, programs, algorithms and
application circuit examples, etc.) is current as of publishing date of this document and is subject to change without
notice.
2.
The circuit examples and the usages described herein are for reference only, and do not guarantee the success of
any specific mass-production design.
ABLIC Inc. is not liable for any losses, damages, claims or demands caused by the reasons other than the products
described herein (hereinafter "the products") or infringement of third-party intellectual property right and any other
right due to the use of the information described herein.
3.
ABLIC Inc. is not liable for any losses, damages, claims or demands caused by the incorrect information described
herein.
4.
Be careful to use the products within their ranges described herein. Pay special attention for use to the absolute
maximum ratings, operation voltage range and electrical characteristics, etc.
ABLIC Inc. is not liable for any losses, damages, claims or demands caused by failures and / or accidents, etc. due to
the use of the products outside their specified ranges.
5.
Before using the products, confirm their applications, and the laws and regulations of the region or country where they
are used and verify suitability, safety and other factors for the intended use.
6.
When exporting the products, comply with the Foreign Exchange and Foreign Trade Act and all other export-related
laws, and follow the required procedures.
7.
The products are strictly prohibited from using, providing or exporting for the purposes of the development of
weapons of mass destruction or military use. ABLIC Inc. is not liable for any losses, damages, claims or demands
caused by any provision or export to the person or entity who intends to develop, manufacture, use or store nuclear,
biological or chemical weapons or missiles, or use any other military purposes.
8.
The products are not designed to be used as part of any device or equipment that may affect the human body, human
life, or assets (such as medical equipment, disaster prevention systems, security systems, combustion control
systems, infrastructure control systems, vehicle equipment, traffic systems, in-vehicle equipment, aviation equipment,
aerospace equipment, and nuclear-related equipment), excluding when specified for in-vehicle use or other uses by
ABLIC, Inc. Do not apply the products to the above listed devices and equipments.
ABLIC Inc. is not liable for any losses, damages, claims or demands caused by unauthorized or unspecified use of
the products.
9.
In general, semiconductor products may fail or malfunction with some probability. The user of the products should
therefore take responsibility to give thorough consideration to safety design including redundancy, fire spread
prevention measures, and malfunction prevention to prevent accidents causing injury or death, fires and social
damage, etc. that may ensue from the products' failure or malfunction.
The entire system in which the products are used must be sufficiently evaluated and judged whether the products are
allowed to apply for the system on customer's own responsibility.
10. The products are not designed to be radiation-proof. The necessary radiation measures should be taken in the
product design by the customer depending on the intended use.
11. The products do not affect human health under normal use. However, they contain chemical substances and heavy
metals and should therefore not be put in the mouth. The fracture surfaces of wafers and chips may be sharp. Be
careful when handling these with the bare hands to prevent injuries, etc.
12. When disposing of the products, comply with the laws and ordinances of the country or region where they are used.
13. The information described herein contains copyright information and know-how of ABLIC Inc. The information
described herein does not convey any license under any intellectual property rights or any other rights belonging to
ABLIC Inc. or a third party. Reproduction or copying of the information from this document or any part of this
document described herein for the purpose of disclosing it to a third-party is strictly prohibited without the express
permission of ABLIC Inc.
14. For more details on the information described herein or any other questions, please contact ABLIC Inc.'s sales
representative.
15. This Disclaimers have been delivered in a text using the Japanese language, which text, despite any translations into
the English language and the Chinese language, shall be controlling.
2.4-2019.07
www.ablic.com
工商网监
湘ICP备2023018690号
