S-8541

Rev.3.2_00 STEP-DOWN, 600 kHz PWM CONTROL or PWM/PFM SWITCHABLE SWITCHING REGULATOR CONTROLLER S-8540/8541 Series The S-8540/8541 Series is a family of CMOS stepdown switching regulator controllers with PWM control (S-8540 Series) and PWM/PFM switchover control (S8541 Series). These devices consist of a reference voltage source, oscillation circuit, an error amplifier, phase compensation circuit, PWM control circuit, current limit circuit. A high efficiency and large current switching regulator is realized with the help of small external components due to the high oscillation frequency, 300 kHz and 600 kHz. The S-8540 Series provides low-ripple voltage, high efficiency, and excellent transient characteristics which come from the PMW control circuit capable of varying the duty ratio linearly from 0 to 100%, the optimized error amplifier, and the phase compensation circuit. The S-8541 Series operates under PWM control when the duty ratio is 29% or higher and operates under PFM control when the duty ratio is less than 29% to ensure high efficiency over all load range. These controllers serve as ideal main power supply units for portable devices due to the high oscillation frequencies together with the small 8-Pin MSOP package. Features • Oscillation frequency • Output voltage • Output voltage precision • Feed back type for output voltage (FB) • External components: • Built-in PWM/PFM switchover control circuit (S-8541 series) • Current limit circuit • Soft-start • Shutdown function • Small package • Lead-free products 600 kHz (A, B types) 300 kHz (C, D types) 1.5 to 6.0 V, selectable in 0.1V steps (A, C types) ±2.0% a transistor, a coil, a diode, and capacitors Duty ratio: 29% (PFM control) 29 to 100% (PWM control) Current is set by an external resistor RSENSE. Time is set by a capacitor CSS and a resistor RSS. 8-Pin MSOP Applications • Power supplies for PDAs, electric organizers, and portable devices. • Power supplies for audio equipment such as portable CD players and headphone stereos. • Main or sub Power supplies for notebook computers and peripheral equipment. Package Package Name 8-Pin MSOP Package FN008-A Drawing Code Tape FN008-A Reel FN008-A Seiko Instruments Inc. 1 STEP-DOWN, 600 kHz PWM CONTROL or PWM/PFM SWITCHABLE SWITCHING REGULATOR CONTROLLER Rev.3.2_00 S-8540/8541 Series Block Diagrams 1. A, C types (fixed output voltage) P ch Pow er M OS FET L VIN Po we r for IC T riangu lar wave o scillatio n circu it PWM comp arato r P hase com pen satio n circuit RS ENS E SENSE 125 mV VO UT VIN EXT SD CIN P WM or PWM / PFM switch ing Sh utdo wn soft start circuit Erro r a mplifier COUT V RE F= 1.0 V V o ltage/c urrent referen ce V SS O N/O FF RS S CS S V ON/ OFF CVREF CV L Figure 1 2. B, D types (feed back) P ch Power MOS FET L VIN Power for IC RS ENS E SENSE V OUT Trian gula r wave oscill ation circuit PWM com parato Phase com pensation circuit Error amplifier 125 mV VOUT CFB RA COUT FB V RE F= 1.0 V V oltage/current reference VIN EXT SD CIN PWM or PWM / PF M switchin g Sh utdown soft start circ uit RB V SS O N/OFF RS S CS S V ON/ OFF CVREF CV L Figure 2 2 Seiko Instruments Inc. STEP-DOWN, 600 kHz PWM CONTROL or PWM/PFM SWITCHABLE SWITCHING REGULATOR CONTROLLER Rev.3.2_00 S-8540/8541 Series Product Name Structure • The control types, product types, and output voltage for the S-8540/8541 series can be selected at the user’s request. Please refer to the “1. Product name” for the definition of the product name and “2. Product Name List” for the full product names. 1. Product name S-854X X XX FN - XXX T2 G IC direction in tape specifications Product code*2 Package code FN: 8-Pin MSOP Output voltage*3 15 to 60 (e.g. When the output voltage is 1.5 V, it is expressed as 15.) Product type A: Fixed output voltage, fosc = 600 kHz B: Feed back type, fosc = 600kHz C: Fixed output voltage, fosc = 300 kHz D: Feed back type, fosc = 300 kHz Control system 0: PWM control 1: PWM/PFM switching control *1 *1. *2. *3. Refer to the taping specifications at the end of this book. Refer to the “2. Product name list”. 00: Feed back type Seiko Instruments Inc. 3 STEP-DOWN, 600 kHz PWM CONTROL or PWM/PFM SWITCHABLE SWITCHING REGULATOR CONTROLLER Rev.3.2_00 S-8540/8541 Series 2. Product name list 2.1 A, B types (oscillation frequency: 600 kHz) Output Voltage (V) Table 1 S-8540XXXFN Series S-8541XXXFN Series 1.5 S-8540A15FN-IAAT2G − 1.6 S-8541A16FN-IGBT2G − 1.8 S-8540A18FN-IADT2G S-8541A18FN-IGDT2G 2.5 S-8540A25FN-IAKT2G S-8541A25FN-IGKT2G 3.3 S-8540A33FN-IAST2G S-8541A33FN-IGST2G 5.0 S-8540A50FN-IBBT2G − Feed back (1.5 to 6.0) S-8540B00FN-IMAT2G S-8541B00FN-IMDT2G Remark Please consult the SII marketing department for products with an output voltage other than those specified above. 2.2 C,D types (oscillation frequency: 300 kHz) Table 2 Output Voltage (V) S-8540XXXFN Series S-8541XXXFN Series 1.8 S-8540C18FN-ICDT2G S-8541C18FN-IIDT2G 2.5 S-8540C25FN-ICKT2G S-8541C25FN-IIKT2G 3.2 S-8541C32FN-IIRT2G − 3.3 S-8540C33FN-ICST2G S-8541C33FN-IIST2G Feed back (1.5 to 6.0) S-8540D00FN-IMBT2G S-8541D00FN-IMET2G Remark Please consult the SII marketing department for products with an output voltage other than those specified above. 4 Seiko Instruments Inc. STEP-DOWN, 600 kHz PWM CONTROL or PWM/PFM SWITCHABLE SWITCHING REGULATOR CONTROLLER Rev.3.2_00 S-8540/8541 Series Pin Configuration Table 3 Pin Description GND pin Connection pin for external transistor IC power supply pin Bypass capacitor connection pin for CVREF reference voltage source Shutdown pin Soft-start capacitor connection pin ON/ OFF • Normal operation (step-down operation) • All circuit halts (no step-down operation) None connected (A, C types) NC*1 FB Feed back pin (B, D types) VOUT Output voltage pin SENSE Current limit detection pin The NC pin is electrically open. The NC pin can be connected to VIN and VSS. Pin Name VSS EXT VIN 8-Pin MSOP TOP view 1 2 3 4 8 7 6 5 Pin No. 1 2 3 4 5 Figure 3 6 7 8 *1. Seiko Instruments Inc. 5 STEP-DOWN, 600 kHz PWM CONTROL or PWM/PFM SWITCHABLE SWITCHING REGULATOR CONTROLLER Rev.3.2_00 S-8540/8541 Series Absolute Maximum Ratings Table 4 Item VIN pin voltage CVREF pin voltage ON/OFF pin voltage FB pin voltage*1 VOUT pin voltage SENSE pin voltage EXT pin voltage EXT pin current Power dissipation Symbol VIN VCVREF VON/OFF VFB VOUT VSENSE VEXT IEXT PD (Ta = 25 °C unless otherwise specified) Absolute Maximum Ratings Unit VSS − 0.3 to VSS + 12 V VSS − 0.3 to VIN + 0.3 V VSS − 0.3 to VSS + 12 V VSS − 0.3 to VSS + 12 V VSS − 0.3 to VSS + 12 V VSS − 0.3 to VSS + 12 V VSS − 0.3 to VIN + 0.3 V ± 100 mA 300 (When not mounted on board) mW mW 500*2 − 40 to + 85 °C − 40 to + 125 °C Operating ambient temperature Topr Storage temperature Tstg *1. Feed back type (B, D types) *2. When mounted on board [Mounted board] (1) Board size : 114.3 mm × 76.2 mm × t1.6 mm (2) Board name : JEDEC STANDARD51-7 Caution The absolute maximum ratings are rated values exceeding which the product could suffer physical damage. These values must therefore not be exceeded under any conditions. (2) When not mounted on board 350 (1) When mounted on board 600 Power dissipation PD (mW) 500 400 300 200 100 0 0 50 100 150 Power dissipation PD (mW) 300 250 200 150 100 50 0 0 50 100 150 Ambient temperature Ta (°C) Ambient temperature Ta (°C) Figure 4 Power Dissipation of Package 6 Seiko Instruments Inc. STEP-DOWN, 600 kHz PWM CONTROL or PWM/PFM SWITCHABLE SWITCHING REGULATOR CONTROLLER Rev.3.2_00 S-8540/8541 Series Electrical Characteristics 1. S-8540/8541 Series A, C types Table 5 (Ta = 25 °C, unless otherwise specified) Parameter Output voltage *1 Input voltage Current consumption 1 Current consumption during shutdown EXT pin output current Line regulation Load regulation Output voltage temperature coefficient Oscillation frequency Maximum duty ratio PWM/PFM-control switch *2 duty ratio Current limit detection voltage SENSE pin input current Shutdown pin input voltage Shutdown pin input leakage current Soft-start time Efficiency Symbol VIN = VOUT (S) × 1.5 IOUT = 120 mA − VIN = VOUT (S) × 1.5 100 % duty ratio S-8540/8541Axx S-8540/8541Cxx Conditions Min. VOUT (S) × 0.980 2.5 − − − − 32 45 − − − 510 255 100 19 100 6.7 2.3 − − 0.1 − 0.1 7.0 − Typ. Max. VOUT (S) × 1.020 10.0 300 240 1.0 − − 60 60 − 690 345 − 39 150 16.8 − 0.3 0.1 0.1 17.0 − Units Measurement Circuit 2 1 1 1 1 1 2 2 2 2 2 2 1 1 2 1 1 1 2 2 VOUT (E) VIN ISS1 ISSS IEXTH IEXTL ΔVOUT1 ΔVOUT2 ΔVOUT ΔTa • VOUT VOUT (S) − 180 140 − − 48 66 30 30 ± 100 600 300 − 29 125 11.2 − − − − 12.0 90 V V μA μA mA mA mV mV ppm/ °C kHz % % mV μA V V μA μA ms % fOSC MaxDuty PFMDuty VSENSE ISENSE VSH VSL ISH ISL tSS EFFI VON/OFF = 0 V VOUT = VOUT (S) × 0.95 VIN = 10 V, VEXT = VIN − 0.2 V VIN = 10 V, VEXT = 0.2 V VOUT (S) × 1.1 ≤ VIN ≤ 10 V, IOUT = 120 mA VIN = VOUT (S) × 1.5, 10 μA ≤ IOUT ≤ 150 mA VIN = VOUT (S) × 1.5, IOUT = 120 mA − 40 ≤ Ta ≤ + 85 °C Measure waveform at the EXT S-8540/8541Axx pin. S-8540/8541Cxx Measure waveform at the EXT pin. VIN = VOUT (S) × 1.5, no load VIN = VOUT (S) × 1.5, Measure waveform at the EXT pin. VIN = VOUT (S) × 1.5, VSENSE = VIN − 0.1 V VIN = VOUT (S) × 1.5, Judge VOUT(S) × 0.98. VIN = VOUT (S) × 1.5, Judge CVREF pin "L". VIN = VOUT (S) × 1.5, VON/OFF = VOUT VIN = VOUT (S) × 1.5, VON/OFF = 0 V Time until VOUT (E) reaches 90% or higher of the VOUT(S) − External components Coil (L) Diode (SD) Output capacitor (COUT) Input capacitor (CIN) Transistor (PSW) Base resistor (Rb) Base capacitor (Cb) CVL CSS RSS RSENSE :Sumida Corporation. CDRH6D28-100 :Matsushita Electric Inducstrial Co., Ltd. MA2Q737 (Schottky diode) :Nichicon Corporation F93 (16 V, 47 μF, tantalum) :Nichicon Corporation F93 (16 V, 47 μF, tantalum) :Toshiba Corporation 2SA1213 :100 mΩ :2200 pF :1.0 μF :0.047 μF :220 kΩ :100 mΩ Condition: Recommended parts are used unless otherwise specified. VIN =VOUT (S) ×1.5 V, IOUT = 120 mA (When VOUT (S) ≤ 1.6 V, then VIN = 2.5 V) *1. VOUT (S) : Specified output voltage value, *2. Applied to the S-8541 series only VOUT (E) : Actual output voltage value Caution 1. Line regulation and load regulation may change greatly due to GND wiring when VIN is high. 2. In the S-8540 series (PWM control), a state in which the duty ratio 0% continues for several clocks may occur when the input voltage is high and the output current is low. In this case, the operation changes to the pseudo PFM mode, but the ripple voltage hardly increases. Seiko Instruments Inc. 7 STEP-DOWN, 600 kHz PWM CONTROL or PWM/PFM SWITCHABLE SWITCHING REGULATOR CONTROLLER Rev.3.2_00 S-8540/8541 Series 2. S-8540/8541 Series B, D types Table 6 (Ta = 25 °C,unless otherwise specified) MeasureMin. Typ. Max. Units ment Circuit VOUT (S) VOUT (S) VOUT (S) V 4 × 0.980 = 3.000 × 1.020 2.5 10.0 V 3 − 180 300 − 3 μA 140 240 − − − 32 45 − − − 510 255 100 19 100 6.7 2.3 − − 0.1 − 0.1 7.0 − − − 48 66 30 30 ± 100 600 300 − 29 125 11.2 − − − − 12.0 90 1.0 − − 60 60 − 690 345 − 39 150 16.8 − 0.3 0.1 0.1 17.0 − μA mA mA mV mV ppm/ °C kHz % % mV μA V V μA μA ms % 3 3 3 4 4 4 4 4 4 3 3 4 3 3 3 4 4 Parameter Output voltage Input voltage Current consumption 1 Current consumption during shutdown EXT pin output current Line regulation Load regulation Output voltage temperature coefficient Oscillation frequency Maximum duty ratio PWM/PFM-control switch duty ratio *3 Current limit detection voltage SENSE pin input current Shutdown pin input voltage Shutdown pin input leakage current Soft-start time Efficiency External components: *1, *2 Symbol VOUT (E) VIN ISS1 ISSS IEXTH IEXTL ΔVOUT1 ΔVOUT2 ΔVOUT ΔTa • VOUT Conditions VIN = 4.5 V IOUT = 120 mA − S-8540/8541B00 VIN = 4.5 V 100% duty ratio S-8540/8541D00 VON/OFF = 0 V VOUT = VOUT (S) × 0.95 VIN = 10 V, VEXT = VIN − 0.2 V VIN = 10 V, VEXT = 0.2 V 3.3 ≤ VIN ≤ 10 V, IOUT = 120 mA 10 μA ≤ IOUT ≤ 150 mA VIN = VOUT (S) × 1.5, IOUT = 120 mA − 40 ≤ Ta ≤ + 85°C Measure waveform at S-8540/8541B00 the EXT pin. S-8540/8541D00 Measure waveform at the EXT pin. VIN = VOUT (S) × 1.5 V, no load VIN = 4.5 V, Measure waveform at the EXT pin. VIN = 4.5 V, VSENSE = VIN − 0.1 V VIN = 4.5 V, Judge VOUT (S) × 0.98. VIN = 4.5 V, Judge CVREF pin "L". VIN = 4.5 V, VON/OFF = VOUT VIN = 4.5 V, VON/OFF = 0 V Time until VOUT (E) reaches 90% or higher of the VOUT (S) − fOSC MaxDuty PFM Duty VSENSE ISENSE VSH VSL ISH ISL tSS EFFI Coil (L) :Sumida Corporation CDRH6D28-100 Diode (SD) :Matsushita Electric Inducstrial Co., Ltd. MA2Q737 (Schottky diode) Output capacitor (COUT) :Nichicon Corporation F93 (16 V, 47 μF, tantalum) Input capacitor (CIN) :Nichicon Corporation F93 (16 V, 47 μF, tantalum) :Toshiba Corporation 2SA1213 Transistor (PSW) Base resistor (Rb) :100 mΩ :2200 pF Base capacitor (Cb) CVL :1.0 μF CSS :0.047 μF RSS :220 kΩ RSENSE :100 mΩ RA :200 kΩ RB :100 kΩ :50 pF CFB Condition: Connect recommended parts unless otherwise specified. VIN =4.5 V, IOUT =120 mA *1. VOUT (S) : Specified output voltage value, VOUT (E) : Actual output voltage value *2. The typical value (specified output voltage value) is VOUT (S) = 1 + RA/RB = 3.0 V. See “Output Voltage adjustment”. *3. S-8541 series only Caution 1. Line regulation and load regulation may change greatly due to GND wiring when VIN is high. 2. In the S-8540 series (PWM control), a state in which the duty ratio 0% continues for several clocks may occur when the input voltage is high and the output current is low. In this case, the operation changes to the pseudo PFM mode, but the ripple voltage hardly increases. 8 Seiko Instruments Inc. STEP-DOWN, 600 kHz PWM CONTROL or PWM/PFM SWITCHABLE SWITCHING REGULATOR CONTROLLER Rev.3.2_00 S-8540/8541 Series Measurement Circuits 1. ON/OFF A CVREF VIN EXT VSS A A A VOUT A A SENSE CIN CVL Figure 5 2. RSS CSS RSENSE + ON/OFF VOUT SENSE CVREF VIN EXT VSS Rb Cb CIN PSW + COUT VON/OFF VI N CVL L SD Figure 6 3. ON/OFF A CVREF VIN EXT A A A RFB1 CFB A VOUT FB CIN CVL RFB2 SENSE A VSS Figure 7 4. CFB CSS + COUT VON/OFF R FB2 ON/OFF VOUT FB SENSE RSENSE VSS L SD C VREF VIN EXT Rb Cb C IN PSW + VIN CVL RSS RFB1 Figure 8 Seiko Instruments Inc. 9 STEP-DOWN, 600 kHz PWM CONTROL or PWM/PFM SWITCHABLE SWITCHING REGULATOR CONTROLLER Rev.3.2_00 S-8540/8541 Series Operation 1. Switching control method 1. 1 PWM control (S-8540 Series) The S-8540 series consists of pulse width modulation (PWM) DC/DC converters. In conventional pulse frequency modulation (PFM) DC/DC converters, pulses are skipped when they operate at low output load current, causing the variation in the ripple frequency and the increase in the ripple voltage of the output voltage both of which constitute inherent drawbacks to those converters. In the S-8540 series the pulse width varies in the range from 0 to 100% according to the load current, yet ripple voltage produced by the switching can easily be removed by a filter since the switching frequency is always constant. These converters thus provide a low-ripple voltage over wide range of input voltage and load current. And it will be skippped to be low current consumption when the pulse width is 0% or it is no load, input current voltage is high. 1. 2 PWM/PFM switchover control (S-8541 Series) The S-8541 series is a DC-DC converter that automatically switches between a pulse width modulation method (PWM) and a pulse frequency modulation method (PFM), depending on the load current, and features low current consumption. The S-8541 series operates under PWM control with the pulse width duty changing from 29 to 100% when the output load current is high. On the other hand, when the output current is low, the S-8541 series operates under PFM control with the pulse width duty fixed at 29%, and pulses are skipped according to the load current. The oscillation circuit thus oscillates intermittently so that the resultant lower self current consumption prevents a reduction in the efficiency when the load current is low. The switching point from PWM control to PFM control depends on the external devices (coil, diode, etc.), input voltage, and output voltage. This series is an especially efficient DC-DC converter at an output current of around 100 μA. 10 Seiko Instruments Inc. STEP-DOWN, 600 kHz PWM CONTROL or PWM/PFM SWITCHABLE SWITCHING REGULATOR CONTROLLER Rev.3.2_00 S-8540/8541 Series 2. Soft-start function The S-8540/8541 series has a built-in soft-start circuit. This circuit enables the output voltage to rise gradually over the specified soft-start time to suppress the overshooting of the output voltage and the rush current from the power source when the power is switched on or the power-off pin is set to "H" The soft-start function of this IC, however, can not suppress rush current to the load completely (Refer to Figure 9) . The rush current is affected by the input voltage and the load. Please evaluate the rush current under the actual test condition. S-8540A33FN (VIN = VON / OFF = 0 → 5 V) 3.0 V V OU T ( 1 V/div) 0V 1A Rush current (0.5 A/div) 0A time (1 ms/div) Figure 9 Waveforms of output voltage and rush current at soft-start The soft-start function of the IC is achieved by raising internal reference voltage gradually, which is caused by the raising of shutdown pin voltage through RC components (RSS and CSS) connected to shutdown pin. A soft-start time (tSS) is changed by RSS, CSS and the input voltage V ON/OFF to RSS. tSS is calculated from the following formula: tSS [ms]=R [kΩ] × C [μF] × In (V ON/OFF [V] / (V ON/OFF [V] − 1.8)) e.g. When RSS = 220 kΩ, CSS = 0.047 μF, V ON/OFF = 2.7 V , then tSS = 11.4 ms. Seiko Instruments Inc. 11 STEP-DOWN, 600 kHz PWM CONTROL or PWM/PFM SWITCHABLE SWITCHING REGULATOR CONTROLLER Rev.3.2_00 S-8540/8541 Series 3. ON/ OFF pin (shutdown pin) This pin deactivates or activates the step-down operation. When the ON / OFF pin is set to "L", the VIN voltage appears through the EXT pin, prodding the switching transistor to go off. All the internal circuits stop working, and substantial savings in current consumption are thus achieved. The ON / OFF pin is configured as shown in Figure 10. Since pull-up or pull-down is not performed internally, please avoid operating the pin in a floating state. Also, try to refrain from applying a voltage of 0.3 to 1.8 V to the pin, lest the current consumption increase. When this ON / OFF pin is not used, leave it coupled to the VIN pin. ON / OFF Pin “H” “L” Table 7 CR Oscillation Circuit Output Voltage Set value OPEN Activated Deactivated VIN ON/OFF VSS Figure 10 12 Seiko Instruments Inc. STEP-DOWN, 600 kHz PWM CONTROL or PWM/PFM SWITCHABLE SWITCHING REGULATOR CONTROLLER Rev.3.2_00 S-8540/8541 Series 4. Current limit circuit The S-8540/8541 series contains a current limit circuit. The current limit circuit is designed to prevent thermal destruction of external transistors due to overload or magnetic saturation of the coil. The current limit circuit can be enabled by inserting a SENSE resistor (RSENSE) between the external coil and the output pin VOUT, and connecting the node for the SENSE resistor and the coil to the SENSE pin. A current limit comparator in the IC is used to check whether the voltage between the SENSE pin and VOUT pin reaches the current limit detection voltage (VSENSE = 125 mV (typ.) ). The current flowing through the external transistor is limited by turning it off during the left time of the oscillation period after detection. The transistor is turned on again at the next clock and current limit detection resumes. If the overcurrent state still persists, the current limit circuit operates again, and the process is repeated. If the overcurrent state is eliminated, the normal operation resumes. Slight overshoot occurs in the output voltage when the overcurrent state is eliminated. Current limit setting value (ILimit) is calculated by the following formula: ILimit = Vsense ( = 125 mV) Rsense If the change with time of the current flowing through the sense resistor is higher than the response speed of the current limit comparator in the IC, the actual current limit value becomes higher than the ILimit (current limit setting value) calculated by the above formula. When the voltage difference between VIN pin and VOUT pin is large, the actual current limit value increases since the change with time of the current flowing through the sense resistor becomes large. 4. 1 VIN vs. Ipeak in the overcurrent state V IN vs. Ipeak (IC: S-8540A33FN, coil: CDRH6D28-100, RS ENSE: 100 m Ω) 3.0 2.5 I peak (A) 2.0 1.5 1.0 1 .25 A 0.5 0.0 2.5 4.0 5.5 7.0 8.5 10.0 V IN (V) Figure 11 lpeak change by input voltage When the output voltage is approximate 1.0 V or less, the load short-circuit protection does not work, since the current limit circuit does not operate. When the current limit circuit is not used, remove the SENSE resistor and connect the SENSE pin to the VSS or VOUT pin. 5. 100% duty cycle The S-8540/8541 series operates up to the maximum duty cycle of 100%. The switching transistor is kept on continuously to supply current to the load, when the input voltage falls below the preset output voltage value. The output voltage in this case is equal to the subtraction of lowering causes by DC resistance of the coil and on resistance of the switching FET from the input voltage. Even when the duty cycle is 100%, the current limit circuit works when overcurrent flows. Seiko Instruments Inc. 13 STEP-DOWN, 600 kHz PWM CONTROL or PWM/PFM SWITCHABLE SWITCHING REGULATOR CONTROLLER Rev.3.2_00 S-8540/8541 Series Selection of Series Products and Associated External Components 1. Selecting a product The S-8540/8541 series is classified into eight types according to the way of control (PWM and PWM/PFM switching), the oscillation frequencies, and output voltage settings (fixed and feed back). Please select the type that suits your needs best by taking the advantage described below into account. 1. 1 Control method: Two different control methods are available: PWM control (S-8540 series) and PWM/PFM switching control (S-8541 series). 1. 2 Oscillation frequencies: The oscillation frequencies are selectable in 600 kHz (A and B types) or 300 kHz (C and D types). Because of their high oscillation frequency, the products in the A and B types allow the use of small size inductors since the peak current decreases when the same load current flows. In addition, they can also be used with small output capacitors. These outstanding features make the A and B types ideal for downsized devices. On the other hand, the C and D types, having lower oscillation frequency, are characterized by small self-consumption current and excellent efficiency under light load. 1. 3 Output voltage setting: Two different types are available: fixed output (A and C types) and feed back type (B and D types). Table 8 provides a rough guide for selecting a product depending on the requirements of the application. Choose the product that has the best score ( ). Table 8 S-8540 A B C D A S-8541 B C D The set output voltage is fixed (1.5 to 6.0 V) Set an output voltage freely (1.5 to 6.0 V) The efficiency at light load (less than 10 mA) is important. The efficiency at 100 mA or more is important. Low-ripple voltage is important. Use of small external parts is Important. Remark : Indispensable condition : Superiority of requirement : Particularly superiority of requirement 14 Seiko Instruments Inc. STEP-DOWN, 600 kHz PWM CONTROL or PWM/PFM SWITCHABLE SWITCHING REGULATOR CONTROLLER Rev.3.2_00 S-8540/8541 Series 2. Inductor The inductance value (L) greatly affects the maximum output current (IOUT) and the efficiency (η). The peak current (IPK) increases by decreasing L and the stability of the circuit improves and IOUT increases. If L is made even smaller, the efficiency falls causing a decline in the current drive capacity for the switching transistor, and IOUT decreases. The loss of IPK by the switching transistor decreases by increasing L and the efficiency becomes maximum at a certain L value. Increasing L further decreases the efficiency due to the loss of coil DC resistance. IOUT also decreases. When the inductance is large in an S-8540/8541 series product, the output voltage may grow unstable in some cases, depending on the conditions of the input voltage, output voltage, and the load current. Perform sufficient evaluation under the actual condition and decide an optimum inductance. The recommended inductances are 10 μH for A, B types and 22 μH for C, D types. When choosing an inductor, attention to its allowable current should be paid since the current over the allowable value will cause magnetic saturation in the inductor, leading to a marked decline in efficiency. An inductor should therefore be selected so as not IPK to surpass its allowable current. The peak current (IPK) is represented by the following equation in non-continuous operation mode: IPK = IOUT + VOUT × (VIN − VOUT) 2 × fOSC × L × VIN Where fOSC is the oscillation frequency. 3. Diode The diode to be externally coupled to the IC should be a type that meets the following conditions: • The forward voltage is low (Schottky barrier diode recommended). • The switching speed is high (50 ns max.). • The reverse direction voltage is higher than VIN. • The current rating is larger than IPK. 4. Capacitors 4. 1 Capacitors (CIN, COUT) The capacitor inserted in the input side (CIN) serves to reduce the power impedance and to average the input current for better efficiency. The CIN value should be selected according to the impedance of the power supply. It should be 47 to 100 μF, although the actual value depends on the impedance of the power source used and load current value. For the output side capacitor (COUT), select a large capacitance with low ESR (Equivalent Series Resistance) to smoothen the ripple voltage. When the input voltage is extremely high or the load current is extremely large, the output voltage may become unstable. In this case the unstable area will become narrow by selecting a large capacitance for an output side capacitor. A tantalum electrolytic capacitor is recommended since the unstable area widens when a capacitor with a large ESR, such as an aluminum electrolytic capacitor, or a capacitor with a small ESR, such as a ceramic capacitor, is chosen. The range of the capacitance should generally be 47 to 100 μF. 4. 2 Internal power source stabilization capacitor (CVL) The main circuits of the IC work on an internal power source connected to the CVREF pin. The CVL is a bypass capacitor for stabilizing the internal Power source. CVL should be a 1 μF ceramic capacitor and wired in a short distance and at a low impedance. Seiko Instruments Inc. 15 STEP-DOWN, 600 kHz PWM CONTROL or PWM/PFM SWITCHABLE SWITCHING REGULATOR CONTROLLER Rev.3.2_00 S-8540/8541 Series 5. External transistor The S-8540/8541 series can work with an enhancement (Pch) MOS FET or a bipolar (PNP) transistor as an external transistor. 5. 1 Enhancement (Pch) MOS FET The EXT pin can directly drive the Pch MOS FET with a gate capacity of approximate 1200 pF. When a Pch MOS FET is chosen, efficiency will be 2 to 3 % higher than that achieved by a PNP bipolar transistor since the MOS FET switching speed is faster than that of the bipolar transistor and power loss due to the base current is avoided. The important parameters in selecting a Pch MOS FET are the threshold voltage, breakdown voltage between gate and source, breakdown voltage between drain and source, total gate capacity, onresistance, and the current ratings. The EXT pin swings from voltage VIN to VSS. When the input voltage is low, a MOS FET with a low threshold voltage has to be used so that the MOS FET will turn on as required. When, conversely, the input voltage is high, select a MOS FET whose gate-source breakdown voltage is higher than the input voltage by at least several volts. Immediately after the power is turned on, or the power is turned off (that is, when the step-down operation is terminated), the input voltage is applied across the drain and the source of the MOS FET. The transistor therefore needs to have drain-source breakdown voltage that is also several volts higher than the input voltage. The total gate capacity and the on-resistance affect the efficiency. The power loss for charging and discharging the gate capacity by switching operation will affect the efficiency at low load current region more when the total gate capacity becomes larger and the input voltage becomes higher. If the efficiency at low load is a matter of concern, select a MOS FET with a small total gate capacity. In regions where the load current is high, the efficiency is affected by power loss caused by the onresistance of the MOS FET. If the efficiency under heavy load is particularly important in the application, choose a MOS FET having on-resistance as low as possible. As for the current rating, select a MOS FET whose maximum continuous drain current rating is higher than IPK. 16 Seiko Instruments Inc. STEP-DOWN, 600 kHz PWM CONTROL or PWM/PFM SWITCHABLE SWITCHING REGULATOR CONTROLLER Rev.3.2_00 S-8540/8541 Series 5. 2 Bipolar (PNP) transistor Figure 12 shows a circuit diagram using Toshiba Corporation 2SA1213-Y for the bipolar transistor (PNP). Using a bipolar transistor, the driving capacity for increasing the output current is determined by the hFE value and the Rb value. 2SA1213-Y VIN Rb Cb EXT V IN Figure 12 The Rb value is given by the following equation: Rb = VIN − 0.7 Ib − 0.4 IEXTL Calculate the necessary base current Ib using the hFE value of the bipolar transistor from the relation, Ib = IPK/hFE, and select a smaller value for Rb which is calculated from the above equation. A small Rb value will certainly contribute to increase the output current, but it will also decrease the efficiency. Determine the optimum value through experiment since the base current flows as pulses and voltage drop may takes place due to the wiring resistance and so on. In addition, if speed-up capacitor Cb is inserted in parallel with resistance Rb, as shown in Figure 12, the switching loss will be reduced, leading to a higher efficiency. by using the following equation : Cb ≤ 1 2π × Rb × fOSC × 0.7 Select a Cb value after performing sufficient evaluation since the optimum Cb value differs depending upon the characteristics of the bipolar transistor. Seiko Instruments Inc. 17 STEP-DOWN, 600 kHz PWM CONTROL or PWM/PFM SWITCHABLE SWITCHING REGULATOR CONTROLLER Rev.3.2_00 S-8540/8541 Series Standard Circuits 1. Fixed output voltage (Pch MOS FET) RSEN SE L Tr VIN P ower for IC T riangular wave oscillation circuit SENSE PWM c omparator + − P hase compe nsation circuit 125mV EXT SD CIN − + PW M, PW M/PFM switching control circuit VOUT VIN E rror amplifier − + V RE F= 1. 0 V COUT S hutdown soft start c irc uit VS S Voltage/ current referenc e ON/OFF One point ground VON/OFF CVREF Figure 13 2. Feed back type (Pch MOS FET) RSEN SE L Tr VIN Power for IC T riangular wave oscillation circuit SENSE + P hase comp ensation circuit PWM comparator − 1 25m V EXT SD CIN circuit VOUT CFB RA COUT FB V SS RB − + PW M, PW M/PFM switching control circuit S hu tdo wn s oft start VIN Error amplifier − + VRE F=1.0 V V oltage/current r eferenc e ON/OFF One point ground VON/OFF CVREF Figure 14 Caution The above connection diagram and constant will not guarantees successful operation. Perform through evaluation using the actual application to set the constant. 18 Seiko Instruments Inc. STEP-DOWN, 600 kHz PWM CONTROL or PWM/PFM SWITCHABLE SWITCHING REGULATOR CONTROLLER Rev.3.2_00 S-8540/8541 Series Precautions Install the external capacitors, diode, coil, and other peripheral components as close to the IC as possible, and make a one-point grounding. When the input voltage is 9 to 10 V, VOUT may vary largely according to the grounding method. When it is difficult to make one-point grounding, use two grounds: one for VIN, CIN, and SD GND, and the other for VOUT, VCVREF, and IC GND. Characteristics ripple voltage and spike noise occur in IC containing switching regulators. Moreover rush current flows at the time of a power supply injection. Because these largely depend on the inductor, the capacitor and impedance of power supply used, fully check them using an actually mounted model. If the input voltage is high and output current is low, pulses with a low duty ratio may appear, and then the 0% duty ratio continues for several clocks. In this case the operation changes to the pseudo pulse frequency modulation (PFM) mode, but the ripple voltage hardly increases. If the input power supply voltage is lower than 1.0 V, the IC operation is unstable and the external switch may be turned on. If input power supply voltage is 10.0 V or higher, the circuit operation is unstable and the IC may be damaged. The input voltage must be in the standard range (2.5 to 10.0 V). The current limit circuit of the IC limits current by detecting a voltage difference of external resistor RSENSE. In choosing the components, make sure that overcurrent will not surpass the allowable dissipation of the switching transistor and the inductor. Make sure that dissipation of the switching transistor will not surpass the allowable power dissipation of the package (especially at high temperature). Do not apply an electrostatic discharge to this IC that exceeds the performance ratings of the built-in electrostatic protection circuit. Seiko Instruments Inc. shall bear no responsibility for any patent infringement by a product that includes an IC manufactured by Seiko Instruments Inc. in relation to the method of using the IC in that product, the product specifications, or the destination country. Seiko Instruments Inc. 19 STEP-DOWN, 600 kHz PWM CONTROL or PWM/PFM SWITCHABLE SWITCHING REGULATOR CONTROLLER Rev.3.2_00 S-8540/8541 Series Application Circuits 1. External adjustment of output voltage The output voltage can be adjusted or changed in the output voltage setting range (1.5 to 6.0 V) by adding external resistors (RA, RB) and a capacitor (CFB) in the S-8540/8541B00AFN and S8540/8541D00AFN, as shown in Figure 15. Temperature gradient can be given by inserting a thermistor in series to RA and RB. RSEN SE L Tr VIN Power for IC T riangular wave oscillation circuit SENSE + − − + P hase comp ensation circuit PWM comparator EXT SD CIN circuit 1 25m V VOUT CFB RA COU T FB V SS RB VIN Error amplifier PW M, PW M/PFM switching control circuit S hu tdo wn s of t start − + VRE F=1.0 V V oltage/current r eferenc e ON/OFF One point ground VON/OFF CVREF Figure 15 Caution The above connection diagram and constant will not guarantees successful operation. Perform through evaluation using the actual application to set the constant. 20 Seiko Instruments Inc. STEP-DOWN, 600 kHz PWM CONTROL or PWM/PFM SWITCHABLE SWITCHING REGULATOR CONTROLLER Rev.3.2_00 S-8540/8541 Series RA, RB must be RA + RB ≤ 2 MΩ and the ratio of RA to RB should be set so that the FB pin is 1.0 V. capacitor (CFB) in parallel to RA to prevent unstable operation like output oscillation. Set the CFB so that f = 1/(2 × πCFB × RA) is 0.1 to 20 kHz (normally 10 kHz). e.g. When VOUT = 3.0 V, RA = 200 kΩ, RB = 100 kΩ, then CFB = 100 pF. Add a The precision of output voltage (VOUT) determined by RA, RB is affected by the precision of the voltage at the FB pin (1 V ± 2.0%), the precision of RA and RB, current input to the FB pin, and IC power supply voltage VDD. Suppose that the FB pin input current is 0 nA, and that the maximum absolute values of the external resistors RA and RB are RA max. and RB max, and the minimum absolute values of the external resistors RA and RB are RA min. and RB min., and that the output voltage shift due to the VDD voltage dependency is ΔV, the minimum value VOUT min. and maximum value VOUT max. of the output voltage VOUT variation is calculated by the following formula: VOUTmin. = (1 + ) × 0.98 − ΔV [V] RBmax. RAmax. VOUTmax. = (1 + ) × 1.02 + ΔV [V] RBmin. RAmin. The precision of the output voltage VOUT cannot be made lower than the precision of the IC output voltage without adjustment of external resistors RA and RB. The lower the RA/RB, the less it is affected by the absolute value precision of the external resistors RA and RB. The lower the RA and RB, the less it is affected by the FB pin input current. To suppress the influence of FB pin input current on the variation of output voltage VOUT, the external resistor RB value must be made sufficiently lower than the input impedance of the FB pin, 1 V/50 nA = 20 MΩ max. Waste current flows through external resistors RA and RB. When it is not a negligible value with respect to load current in actual use, the efficiency decreases. The RA and RB values of the external resistors must therefore be made sufficiently high. Evaluation of the influence of the noise is needed in the actual condition If the RA and RB values of resistors are high (1 MΩ or higher) since they are susceptible to external noise. The output voltage VOUT precision and the waste current are in a trade-off relation. considered according to application requests. They must be Seiko Instruments Inc. 21 STEP-DOWN, 600 kHz PWM CONTROL or PWM/PFM SWITCHABLE SWITCHING REGULATOR CONTROLLER Rev.3.2_00 S-8540/8541 Series Typical Characteristics 1. Examples of major parameters characteristics (1) ISS1 − VIN S-8540/8541(300 kHz) (2) ISS1 − VIN 250 200 250 S-8540/8541(600 kHz) ISS1 (μA) 25°C 85°C 200 85°C 150 100 50 0 2.5 4.0 5.5 7.0 8.5 10.0 Ta=−40°C ISS1 (μA) 150 100 25°C 50 0 2.5 4.0 5.5 7.0 8.5 10.0 Ta=−40°C VIN (V) VIN (V) (3) fOSC − VIN 360 340 S-8540/8541(300 kHz) 85°C (4) fOSC − VIN 720 680 S-8540/8541(600 kHz) 85°C fOSC (kHz) fOSC (kHz) 320 300 280 260 240 2.5 4.0 5.5 7.0 8.5 10.0 25°C Ta=−40°C 640 600 560 520 480 2.5 4.0 5.5 7.0 8.5 10.0 25°C Ta=−40°C VIN (V) VIN (V) (5) IEXTH − VIN 100 S-8540/8541 (6) IEXTL − VIN 100 80 S-8540/8541 IEXTH (mA) 60 40 20 0 2.5 Ta=−40°C IEXTL (mA) 80 25°C 60 40 20 Ta=−40°C 25°C 85°C 8.5 10.0 85°C 4.0 5.5 7.0 8.5 10.0 0 2.5 4.0 5.5 7.0 VIN (V) VIN (V) (7) VSH − VIN S-8540/8541 2.3 2.2 Ta=−40°C (8) VSL − VIN S-8540/8541 0.9 0.8 25°C Ta=−40°C VSH (V) VSL (V) 2.1 2.0 1.9 1.8 1.7 2.5 0.7 0.6 0.5 0.4 0.3 25°C 85°C 4.0 5.5 7.0 8.5 10.0 85°C 2.5 4.0 5.5 7.0 8.5 10.0 VIN (V) VIN (V) 22 Seiko Instruments Inc. STEP-DOWN, 600 kHz PWM CONTROL or PWM/PFM SWITCHABLE SWITCHING REGULATOR CONTROLLER Rev.3.2_00 S-8540/8541 Series (9) tSS − VIN 16 15 14 13 12 11 10 9 8 2.5 Ta=−40°C tSS (ms) 25°C 85°C 8.5 10.0 4.0 5.5 7.0 VIN (V) (10) VOUT − VIN 1.8 V 1.85 1.83 PWM/PFM 600 kHz (11) VOUT − VIN 3.3 V 3.40 PWM/PFM 600 kHz IOUT =0.1 mA IOUT =0.1 mA 3.35 100 mA VOUT (V) 1.81 1.79 1.77 1.75 2.5 4 5.5 7 8.5 10 100 mA 400 mA VOUT (V) 3.30 400 mA 3.25 3.20 2.5 4.0 5.5 7.0 8.5 10.0 VIN (V) VIN (V) (12) VOUT − VIN 3.3 V 3.40 3.35 PWM 600 kHz (13) VOUT − VIN 3.3 V 3.40 PWM/PFM 300 kHz IOU T =0.1 mA 100 mA IO UT =0.1 mA 100 mA 3.30 400 mA 3.25 3.20 2.5 4.0 5.5 7.0 8.5 10.0 VO UT (V) 3.35 3.30 400 mA 3.25 3.20 2.5 4.0 5.5 7.0 8.5 10.0 VO UT(V) VIN (V) VIN ( V) Seiko Instruments Inc. 23 STEP-DOWN, 600 kHz PWM CONTROL or PWM/PFM SWITCHABLE SWITCHING REGULATOR CONTROLLER Rev.3.2_00 S-8540/8541 Series 2. Transient Response Characteristics 2. 1 Power-on (IOUT: no Load) (1) S-8540A33FN (VIN: 0 → 4.95 V) 10 V VIN (2.5 V/div ) 0V 3V V OUT (1 V/div ) 0V t (2 ms/div ) 10 V V IN (2.5 V/div ) 0V 3V VOUT (1 V/div ) 0V t (1 ms/div ) (2) S-8540A33FN (VIN: 0 → 10 V) (3) S-8540C33FN (VIN: 0 → 4.95 V) 10 V VIN ( 2.5 V/div) 0V 3V VOUT (1 V/div ) 0V t (2 ms/div) (4) S-8540C33FN (VIN: 0 → 10 V) 10 V VIN (2.5 V/div) 0V 3V VOU T (1 V/div ) 0V t (1 ms/div ) (5) S-8540A18FN (VIN: 0 → 2.7 V) 10 V V IN ( 2.5 V/div) 0V 2V VOUT ( 0.5 V/div) 0V t (4 ms/div) (6) S-8540A18FN (VIN: 0 → 10 V) 10 V VIN ( 2.5 V/div) 0V 2V V OUT ( 0.5 V/div) 0V t (1 ms/div ) 24 Seiko Instruments Inc. STEP-DOWN, 600 kHz PWM CONTROL or PWM/PFM SWITCHABLE SWITCHING REGULATOR CONTROLLER Rev.3.2_00 S-8540/8541 Series 2. 2 Shutdown pin response (VON/OFF : 0 → 2.5 V IOUT: no Load) (2) S-8540A33FN (VIN: 10V) 4V (1) S-8540A33FN (VIN: 4.95V) 4V VON/OFF (1 V/div ) 0V 3V VOUT (1 V/div ) 0V t (4 ms/div ) VON/OFF (1 V/div ) 0V 3V VOUT (1 V/div ) 0V t (4 ms/div) (3) S-8540C33FN (VIN: 4.95 V) 4V (4) S-8540C33FN (VIN: 10 V) 4V VON/OF F (1 V/div ) 0V 3V VOUT (1 V/div ) 0V VON/OFF (1 V/div ) 0V 3V VOUT (1 V/div ) 0V t (4 ms/div) t (4 ms/div ) (5) S-8540A18FN (VIN: 4.95 V) 4V VON /OF F (1 V/div ) 0V 1.5 V VOUT (0.5 V/div) 0V t (4 ms/div) (6) S-8540A18FN (VIN: 10 V) 4V VON /OF F (1 V/div ) 0V 1.5 V VOUT ( 0.5 V/div) 0V t (4 ms/div) Seiko Instruments Inc. 25 STEP-DOWN, 600 kHz PWM CONTROL or PWM/PFM SWITCHABLE SWITCHING REGULATOR CONTROLLER Rev.3.2_00 S-8540/8541 Series 2. 3 Supply Voltage Variation (VIN: 3.6→9.0→3.6 V) (2) S-8540A33FN (IOUT: 500 mA) 10 V VIN (2.5 V/div) 0V (1) S-8540A33FN (IOUT: 10 mA) 10 V VIN (2.5 V/div ) 0V VOUT (0.1 V/div) VOUT (0.1 V/div) t (0.4 ms/div ) t (0.4 ms/div) (3) S-8540C33FN (IOUT: 10 mA) 10 V V IN (2.5 V/div) 0V (4) S-8540C33FN (IOUT: 500 mA) 10 V VIN ( 2.5 V/div) 0V VOUT ( 0.1 V/div) VOUT (0.1 V/div) t (0.4 ms/div ) t (0.4 ms/div ) (5) S-8540A18FN (IOUT: 10 mA) 10 V VIN ( 2.5 V/div) 0V (6) S-8540A18FN (IOUT: 500 mA) 10 V V IN ( 2.5 V/div) 0V VOUT ( 0.1 V/div) VOUT (0.1 V/div ) t (0.4 ms/div) t (0.4 ms/div) 26 Seiko Instruments Inc. STEP-DOWN, 600 kHz PWM CONTROL or PWM/PFM SWITCHABLE SWITCHING REGULATOR CONTROLLER Rev.3.2_00 S-8540/8541 Series 2. 4 Load Variation (VIN: 2.7 V or 5.0 V or 7.5 V, IOUT: 0.1→500 mA, 500→0.1 mA) (2) S-8540A33FN (VIN: 4.95 V) 500 mA IOU T 0.1 mA (1) S-8540A33FN (VIN: 4.95 V) 500 mA IOUT 0.1 mA V OUT ( 0.1 V/div ) VOUT ( 0.1 V/div) t (0.2 ms/div) t (4 ms/div) (3) S-8540C33FN(VIN: 4.95 V) (4) S-8540C33FN(VIN: 4.95 V) 500 mA 500 mA IOUT 0.1 mA IOUT 0.1 mA VOUT ( 0.1 V/div ) VOUT (0.1 V/div) t (0.2 ms/div) t ( 8 ms/div) (5) S-8540A18FN (VIN: 2.7 V) (6) S-8540A18FN (VIN: 2.7 V) 500 mA 500 mA IOU T 0.1 mA IOU T 0.1 mA VOU T ( 0.1 V/div) V OUT (0.1 V/div ) t (0.2 ms/div) t (4 ms/div) Seiko Instruments Inc. 27 STEP-DOWN, 600 kHz PWM CONTROL or PWM/PFM SWITCHABLE SWITCHING REGULATOR CONTROLLER Rev.3.2_00 S-8540/8541 Series Reference Data This reference data is intended to help you select peripheral components to be externally connected to the IC. Therefore, this information provides recommendations on external components selected with a view to accommodating a wide variety of IC applications. Characteristic data is duly indicated in the table below. Table 9. External components list for efficiency (Small and thin application using 1.3 mm or less tall components, maximum load current : IOUT = 0.9 A) Output Modulation fOSC No. Product Name Inductor Transistor Diode Output Capacitor Voltage 1.1 1.2 1.3 1.4 1.5 1.6 S-8540A33FN S-8541A33FN S-8540A25FN 3.3 V PWM PWM/PFM PWM 2.5 V S-8541A25FN S-8540A18FN 1.8 V S-8541A18FN PWM/PFM PWM/PFM PWM 600kHz LDR655312T-4R7 CPH6301 RB491D F920J476MB × 2 Table 10 External components list for efficiency (High efficiency application using 3.0mm or less tall components, maximum load current : IOUT = 1.0 A) Output Modulation fOSC No. Product Name Inductor Transistor Diode Output Capacitor Voltage 1.7 1.8 1.9 S-8540C33FN S-8541C33FN S-8540C25FN 3.3 V PWM PWM/PFM PWM 2.5 V 1.10 S-8541C25FN 1.11 S-8540C18FN 300kHz PWM/PFM PWM CDRH6D28-220 CPH6301 RB491D F931A476MC × 1 1.8 V 1.12 S-8541C18FN PWM/PFM Table 11 External components list for ripple voltage No. 2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.8 Product Name S-8540A33FN S-8541A33FN S-8540A18FN Output Modulation Voltage 3.3 V PWM PWM/PFM PWM 1.8 V PWM/PFM PWM 3.3 V PWM/PFM fOSC Inductor Transistor Diode Output Capacitor 600kHz LDR655312T-4R7 CPH6301 RB491D F920J476MB × 2 S-8541A18FN S-8540C33FN S-8541C33FN S-8540C18FN 1.8 V S-8541C18FN 300kHz PWM PWM/PFM CDRH6D28-220 CPH6301 RB491D F931A476MC × 1 28 Seiko Instruments Inc. STEP-DOWN, 600 kHz PWM CONTROL or PWM/PFM SWITCHABLE SWITCHING REGULATOR CONTROLLER Rev.3.2_00 S-8540/8541 Series Table 12 External parts function Component Product Name LDR655312T-4R7 Manufacturer TDK Corporation Sumida Corporation Rohm Corporation Nichicon Corporation Nichicon Corporation Sanyo Electric Co., Ltd. L-Value 4.7 μH 22.0 μH DC Resistance 0.19 Ω 0.128 Ω Maximum Current 0.9 A 1.2 A Size (L × W × H) [mm] 6.5 × 5. 3 × 1.25 7.0 × 7.0 × 3.0 3.0 × 3.1 × 1.3 3.6 × 3.0 × 1.2 6.2 × 3.4 × 2.7 2.9 × 2.8 × 0.9 Inductor CDRH6D28-220 Diode RB491D Forward current 1.0 A at VF = 0.45 V, Vrm = 25V 47 μF, 6.3 V 47 μF, 10.0 V Vdss =20 V max., Vgss =10 V max., ID =3.0 A max., Ciss =360 pF, Ron =110 mΩ Output F920J476MB Capacity (tantalum F931A476MC electrolytic) Transistor CPH6301 (MOS FET) Seiko Instruments Inc. 29 STEP-DOWN, 600 kHz PWM CONTROL or PWM/PFM SWITCHABLE SWITCHING REGULATOR CONTROLLER Rev.3.2_00 S-8540/8541 Series Efficiency Characteristics : Efficiency (η) − Output current (IOUT) S-8540A33FN (3.3 V, 600 kHz, PWM control) 100 V IN=4.0 V 1. 1. 1 1. 2 S-8541A33FN (3.3 V, 600 kHz, PWM/PFM control) VIN=4.0 V 100 Efficiency η (%) Efficiency η (%) 90 80 70 60 50 1 90 80 70 60 50 1 5.0 V 7.2 V 5.0 V 7.2 V 10 100 1000 10 100 1000 I OUT (mA) IOUT (mA) 1. 3 S-8540A25FN 100 (2.5 V, 600 kHz, PWM control) 1. 4 100 S-8541A25FN (2.5 V, 600 kHz, PWM/PFMcontrol) Efficienc y η (%) 80 70 60 50 1 10 100 1000 3.6 V 5.0 V Efficiency η (%) 90 V IN=3.0 V 90 80 70 60 50 1 VIN=3.0 V 3.6 V 5.0 V 10 100 1000 IOUT (mA) IOUT (mA) 1. 5 100 S-8540A18FN ( 1.8 V, 600 kHz, PWM control) 1. 6 100 S-8541A18FN (1.8 V, 600 kHz, PWM/PFM control) VIN=2.5 V Efficiency η (%) Efficienc y η (% ) 90 80 70 VIN=2.5 V 90 80 70 60 50 1 3.6 V 60 50 1 10 100 5.0 V 3.6 V 5.0 V 1000 10 100 1000 I OUT (mA) IOUT (mA) 30 Seiko Instruments Inc. STEP-DOWN, 600 kHz PWM CONTROL or PWM/PFM SWITCHABLE SWITCHING REGULATOR CONTROLLER Rev.3.2_00 S-8540/8541 Series 1. 7 100 S-8540C33FN (3.3 V, 300 kHz, PWM control) VI N=4.0 V 1. 8 100 S-8541C33FN (3.3 V, 300 kHz, PWM/PFM control) VIN =4.0 V Efficiency η (%) Efficiency η (%) 90 80 70 60 50 1 10 100 1000 5.0 V 7.2 V 90 80 70 60 50 1 5.0 V 7.2 V 10 100 1000 IOUT (mA) IOUT (mA) 1. 9 S-8540C25FN 100 ( 2.5 V, 300 kHz, PWM control) 1. 10 100 S-8541C25FN (2.5 V, 300 kHz, PWM/PFM control) VIN =3.0 V Efficiency η (% ) 90 80 70 60 50 1 Efficiency η (%) VIN=3.0 V 90 80 70 60 50 1 5.0 V 3.6 V 5.0 V 3.6 V 10 100 1000 10 100 1000 IOUT (mA) IOUT (mA) 1. 11 S-8540C18FN (1.8 V, 300 kHz, PWM control) VIN =2.5 V 1. 12 100 S-8541C18FN (1.8 V,300 kHz, PWM/PFM control) VIN =2.5 V 100 Efficiency η (%) 80 70 60 50 1 10 100 1000 3.6 V 5.0 V Efficiency η (% ) 90 90 80 70 60 50 1 3.6 V 5.0 V 10 100 1000 IOUT (mA) IOUT (mA) Seiko Instruments Inc. 31 STEP-DOWN, 600 kHz PWM CONTROL or PWM/PFM SWITCHABLE SWITCHING REGULATOR CONTROLLER Rev.3.2_00 S-8540/8541 Series 2. Ripple Voltage (Vrip) − Output Current (IOUT) Characteristics 2. 1 S-8540A33FN 2. 2 S-8541A33FN 100 80 (3.3 V, 600 kHz, PWM control) 7.2 V 100 (3.3 V, 600 kHz, PWM/PFM control) Ripple (mV) 60 40 20 0 1 10 5.0 V V IN=4.0 V Ripple (mV) 80 60 40 20 0 V IN=4.0 V 5.0 V 7.2 V 100 1000 1 10 100 1000 IOUT (mA) IOUT (mA) 2. 3 100 S-8540A18FN (1.8 V, 600 kHz, PWM control) 2. 4 100 S-8541A18FN (1.8 V, 600 kHz, PWM/PFM control) 60 40 20 0 1 10 V IN=2.5 V 3.6 V 5.0 V Ripple (mV) Ripple (mV) 80 80 60 40 20 0 3.6 V VIN=2.5 V 5.0 V 100 1000 1 10 100 1000 IOUT (mA) IOUT (mA) 2. 5 S-8540C33FN 100 ( 3.3 V, 600 kHz, PWM control) 2. 6 S-8541C33FN 100 (3.3 V, 600 kHz, PWM/PFM control) Ripple (mV) 3.6 V 60 40 20 0 1 10 100 1000 VIN=2.5 V 5.0 V Ripple (mV) 80 80 60 40 20 0 1 10 100 1000 VIN =2.5 V 3.6 V 5.0 V IOUT (mA) IOUT (mA) 2. 7 S-8540C18FN (1.8 V, 300 kHz, PWM control) 100 2. 8 S-8541C18FN 100 (1.8 V, 300 kHz, PWM/PFM control) Ripple (mV) 60 3.6 V 40 20 0 1 10 100 1000 V IN=2.5 V 5.0 V Ripple (mV) 80 80 60 40 20 0 1 10 100 1000 V IN=2.5 V 3.6 V 5.0 V IOUT (mA) IOUT (mA) 32 Seiko Instruments Inc. 2.95±0.2 8 5 1 4 0.13±0.1 0.2±0.1 0.65±0.1 No. FN008-A-P-SD-1.1 TITLE No. SCALE UNIT MSOP8-A-PKG Dimensions FN008-A-P-SD-1.1 mm Seiko Instruments Inc. 2.0±0.05 4.0±0.1 4.0±0.1 1.35±0.15 1.55±0.05 1.05±0.05 0.3±0.05 3.1±0.15 4 1 5 8 Feed direction No. FN008-A-C-SD-1.1 TITLE No. SCALE UNIT MSOP8-A-Carrier Tape FN008-A-C-SD-1.1 mm Seiko Instruments Inc. 16.5max. Enlarged drawing in the central part 13±0.2 13.0±0.3 (60°) (60°) No. FN008-A-R-SD-1.1 TITLE No. SCALE UNIT mm MSOP8-A-Reel FN008-A-R-SD-1.1 QTY. 3,000 Seiko Instruments Inc. • • • • • • The information described herein is subject to change without notice. Seiko Instruments Inc. is not responsible for any problems caused by circuits or diagrams described herein whose related industrial properties, patents, or other rights belong to third parties. The application circuit examples explain typical applications of the products, and do not guarantee the success of any specific mass-production design. When the products described herein are regulated products subject to the Wassenaar Arrangement or other agreements, they may not be exported without authorization from the appropriate governmental authority. Use of the information described herein for other purposes and/or reproduction or copying without the express permission of Seiko Instruments Inc. is strictly prohibited. The products described herein cannot be used as part of any device or equipment affecting the human body, such as exercise equipment, medical equipment, security systems, gas equipment, or any apparatus installed in airplanes and other vehicles, without prior written permission of Seiko Instruments Inc. Although Seiko Instruments Inc. exerts the greatest possible effort to ensure high quality and reliability, the failure or malfunction of semiconductor products may occur. The user of these products should therefore give thorough consideration to safety design, including redundancy, fire-prevention measures, and malfunction prevention, to prevent any accidents, fires, or community damage that may ensue.