BLE112-A-V1

BLE112 DATA SHEET Thursday, 20 March 2014 Version 1.44 Copyright © 2000-2014 Bluegiga Technologies All rights reserved. Bluegiga Technologies assumes no responsibility for any errors which may appear in this manual. Furthermore, Bluegiga Technologies reserves the right to alter the hardware, software, and/or specifications detailed here at any time without notice and does not make any commitment to update the information contained here. Bluegiga’s products are not authorized for use as critical components in life support devices or systems. The WRAP is a registered trademark of Bluegiga Technologies The Bluetooth trademark is owned by the Bluetooth SIG Inc., USA and is licensed to Bluegiga Technologies. All other trademarks listed herein are owned by their respective owners. Bluegiga Technologies Oy VERSION HISTORY Version Comment 1.0 Certification information updated. Layout guide for BLE112-N added. 1.1 RF pin dimensions added 1.11 Absolute maximum supply corrected 1.2 Certification information updated 1.21 Current consumption added 1.22 Current consumption profiles added 1.23 Typo corrected on table 2 1.24 UART chapter, I/O Ports chapter, DC characteristics 1.25 Updated product codes 1.26 Note about P1_0 and P1_1 in chapter 2.1 1.27 Design check list, peripheral pull-up/pull-down requirements 1.28 Updating “Alternate” configuration table for clarity 1.29 Absolute maximum ratings: all supply nets must have the same voltage. Opamp and comparator removed from the peripherals table. 1.3 MIC Japan information updated 1.4 Updated contact information 1.41 CE info updated 1.42 TXP vs HW config added 1.43 Peripheral mapping table: analog comparator added 1.44 Product codes updates Bluegiga Technologies Oy TABLE OF CONTENTS 1 BLE112 Product numbering ..........................................................................................................................6 2 Pinout and Terminal Description ...................................................................................................................7 2.1 I/O Ports .............................................................................................................................................. 10 2.2 UART ................................................................................................................................................... 10 2.3 Electrical Characteristics ..................................................................................................................... 11 2.4 Absolute Maximum Ratings ................................................................................................................ 11 2.5 Recommended Operating Conditions ................................................................................................. 11 2.6 DC Characteristics .............................................................................................................................. 11 2.7 Current Consumption .......................................................................................................................... 12 2.8 RF Characteristics ............................................................................................................................... 13 2.8.1 TX Power vs HW Configuration ................................................................................................... 13 2.8.2 Antenna characteristics ................................................................................................................ 13 3 Physical Dimensions .................................................................................................................................. 16 4 Power-On Reset and Brownout Detector ................................................................................................... 18 5 Design Guidelines ...................................................................................................................................... 19 5.1 General Design Guidelines ................................................................................................................. 19 5.2 Layout Guide Lines ............................................................................................................................. 20 5.3 BLE112-A Layout Guide ..................................................................................................................... 20 5.4 BLE112-N Layout Guide ..................................................................................................................... 21 5.5 Design Check List ............................................................................................................................... 22 6 Soldering Recommendations ..................................................................................................................... 23 7 Block diagram ............................................................................................................................................. 24 8 Certifications ............................................................................................................................................... 27 8.1 Bluetooth ............................................................................................................................................. 27 8.2 FCC and IC ......................................................................................................................................... 27 8.2.1 9 FCC et IC ..................................................................................................................................... 28 8.3 CE ....................................................................................................................................................... 30 8.4 MIC Japan ........................................................................................................................................... 30 8.5 KCC (Korea) ........................................................................................................................................ 30 8.6 Qualified Antenna Types for BLE112-E and BLE112-N ..................................................................... 30 Contact Information .................................................................................................................................... 32 Bluegiga Technologies Oy BLE112 Bluetooth® low energy single mode module DESCRIPTION BLE112, Bluetooth low energy single mode module is a single mode device targeted for low power sensors and accessories. BLE112 offers all Bluetooth low energy features: radio, stack, profiles and application space for customer applications, so no external processor is needed. The module also provides flexible hardware interfaces to connect sensors, simple user interfaces or even displays directly to the module. BLE112 can be powered directly with a standard 3V coin cell batteries or pair of AAA batteries. In lowest power sleep mode it consumes only 400nA and will wake up in few hundred microseconds. APPLICATIONS: KEY FEATURES:      Heart rate sensors  Pedometers  Watches  Blood pressure and glucose meters  Bluetooth v.4.0, single mode compliant o Supports master and slave modes o 4+ simultaneous connection in master mode Integrated Bluetooth low energy stack o GAP, GATT, L2CAP, SMP o Bluetooth low energy profiles Radio performance o TX power: +3dBm to -23dBm o RX sensitivity: -85dBm to 91dBm Ultra low current consumption o Transmit: 27mA (0dBm) o Sleep mode 3: 0.4uA  Programmable 8051 processor for embedding full applications Weight scales  Bluetooth qualified  Key fobs  CE qualified  Households devices  Modular certification for FCC, IC and KCC  Security tags   Wireless keys (keyless go) MIC Japan compatibility fully tested with ARIB STD-T66  Proximity sensors  HID keyboards and mice  Indoor GPS broadcasting devices sensors and collector Bluegiga Technologies Oy 1 BLE112 Product numbering Product code Description BLE112-A-v1 BLE112 with integrated chip antenna and software version 1.0 BLE112-E-v1 BLE112 with U.FL connector and software version 1.0 Bluegiga Technologies Oy Page 6 of 33 1 GND 2 AVDD RF 31 Pinout and Terminal Description RFGND 32 2 3 AVDD 4 P2_2 5 P2_1 GND 30 6 P2_0 7 P1_7 RESET 29 P0_0 28 8 P1_6 P0_1 27 9 VDD_USB P0_2 26 21 GND 20 DVDD P0_6 22 19 P0_7 P0_5 23 13 P1_5 18 P1_0 12 USB- 17 P1_1 P0_4 24 16 P1_2 11 USB+ 15 P1_3 P0_3 25 14 P1_4 10 GND Figure 1: BLE112 RESET PIN NUMBER 29 PAD TYPE Active low reset. 1, 10, 21, 30 GND RF 31 RF (* RFGND 32 GND DVDD AVDD VDD_USB 20 2, 3 9 Supply voltage Supply voltage Supply voltage GND DESCRIPTION GND RF output/input for BLE112-N. With BLE112-A and BLE112-E do not connect. RF ground. Connected to GND internally in the module. With BLE112-A and BLE112-E leave floating or connect to a solid GND plane. Supply voltage 2V - 3.6V Supply voltage 2V - 3.6V Supply voltage 2V - 3.6V *) RF pin is not connected in BLE112-A and BLE112-E. To use RF pin with BLE112-B please see the design guide. Table 1: Supply and RF Terminal Descriptions Bluegiga Technologies Oy Page 7 of 33 PIN PIN NAME PIN TYPE NUMBER DESCRIPTION 4 P2_2 Digital I/O Configurable I/O port, See table 3 5 P2_1 Digital I/O Configurable I/O port, See table 3 6 7 8 11 12 13 14 15 16 P2_0 P1_7 P1_6 USB+ USBP1_5 P1_4 P1_3 P1_2 Digital Digital Digital USB+ USBDigital Digital Digital Digital 17 P1_1 Digital I/O 18 P1_0 Digital I/O 19 22 23 24 25 26 27 28 P0_7 P0_6 P0_5 P0_4 P0_3 P0_2 P0_1 P0_0 Digital Digital Digital Digital Digital Digital Digital Digital Configurable I/O Configurable I/O Configurable I/O USB data plus USB data minus Configurable I/O Configurable I/O Configurable I/O Configurable I/O Configurable I/O table 3 Configurable I/O table 3 Configurable I/O Configurable I/O Configurable I/O Configurable I/O Configurable I/O Configurable I/O Configurable I/O Configurable I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O port, See table 3 port, See table 3 port, See table 3 port, See table 3 port, See table 3 port, See table 3 port, See table 3 port with 20mA driving capability, See port with 20mA driving capability, See port, port, port, port, port, port, port, port, See See See See See See See See table table table table table table table table 3 3 3 3 3 3 3 3 Table 2: Terminal Descriptions *) BLE112 is configurable as either SPI master or SPI slave Bluegiga Technologies Oy Page 8 of 33 PERIPHERAL / FUNCTION Analog Comparator ADC USART 0 SPI (** USART 0 UART USART 1 SPI (** USART 1 UART TIMER 1 TIMER 3 TIMER 4 P0 5 4 3 2 1 0 + A7 A6 A5 A4 A3 A2 A1 A0 7 6 C Alt.1 P1 7 6 3 2 1 0 2 P2 1 HARDWARE.XML Example (* 0 SS MO MI