C8051F02x-DK
C8051F02 X D EVELOPMENT K IT U SER ’ S G U I D E
1. Kit Contents
The C8051F02x Development Kit contains the following items:
• C8051F020 Target Board
• C8051Fxxx Development Kit Quick-Start Guide
• Silicon Laboratories IDE and Product Information CD-ROM. CD content includes:
• Silicon Laboratories Integrated Development Environment (IDE)
• Keil 8051 Development Tools (macro assembler, linker, evaluation ‘C’ compiler)
• Source code examples and register definition files
• Documentation
• C8051F02x Development Kit User’s Guide (this document)
• AC to DC Power Adapter
• USB Debug Adapter (USB to Debug Interface)
• USB Cable
2. Hardware Setup using a USB Debug Adapter
The target board is connected to a PC running the Silicon Laboratories IDE via the USB Debug Adapter as shown
in Figure 1.
1.
2.
3.
4.
Connect the USB Debug Adapter to the JTAG connector on the target board with the 10-pin ribbon cable.
Connect one end of the USB cable to the USB connector on the USB Debug Adapter.
Connect the other end of the USB cable to a USB Port on the PC.
Connect the ac/dc power adapter to power jack P1 on the target board.
Notes:
• Use the Reset button in the IDE to reset the target when connected using a USB Debug Adapter.
• Remove power from the target board and the USB Debug Adapter before connecting or disconnecting the
ribbon cable from the target board. Connecting or disconnecting the cable when the devices have power can
damage the device and/or the USB Debug Adapter.
AC/DC
Adapter
PC
Target Board
USB Debug Adapter
PWR
SILICON LABORATORIES
RESET P3.7
Run
Stop
Silicon Laboratories
USB DEBUG ADAPTER
Power
USB
Cable
MCU
P1.6
Port 2
Port 0
Port 1
Port 3
Port 4
Figure 1. Hardware Setup using a USB Debug Adapter
Rev. 0.6 9/06
Copyright © 2006 by Silicon Laboratories
C8051F02x-DK
C8051F02x-DK
3. Software Setup
The included CD-ROM contains the Silicon Laboratories Integrated Development Environment (IDE), Keil software
8051 tools and additional documentation. Insert the CD-ROM into your PC’s CD-ROM drive. An installer will automatically launch, allowing you to install the IDE software or read documentation by clicking buttons on the Installation Panel. If the installer does not automatically start when you insert the CD-ROM, run autorun.exe found in the
root directory of the CD-ROM. Refer to the readme.txt file on the CD-ROM for the latest information regarding
known IDE problems and restrictions.
4. Silicon Laboratories Integrated Development Environment
The Silicon Laboratories IDE integrates a source-code editor, source-level debugger and in-system Flash programmer. The use of third-party compilers and assemblers is also supported. This development kit includes the Keil
Software A51 macro assembler, BL51 linker and evaluation version C51 ‘C’ compiler. These tools can be used
from within the Silicon Laboratories IDE.
4.1. System Requirements
The Silicon Laboratories IDE requirements:
• Pentium-class host PC running Microsoft Windows 98SE or later.
• One available COM or USB port.
• 64 MB RAM and 40 MB free HD space recommended.
4.2. Assembler and Linker
A full-version Keil A51 macro assembler and BL51 banking linker are included with the development kit and are
installed during IDE installation. The complete assembler and linker reference manual can be found under the Help
menu in the IDE or in the “Silabs\MCU\hlp” directory (A51.pdf).
4.3. Evaluation C51 ‘C’ Compiler
An evaluation version of the Keil C51 ‘C’ compiler is included with the development kit and is installed during IDE
installation. The evaluation version of the C51 compiler is the same as the full professional version except code
size is limited to 4 kB and the floating point library is not included. The C51 compiler reference manual can be
found under the Help menu in the IDE or in the “Silabs\MCU\hlp” directory (C51.pdf).
4.4. Using the Keil Software 8051 Tools with the Silicon Laboratories IDE
To perform source-level debugging with the IDE, you must configure the Keil 8051 tools to generate an absolute
object file in the OMF-51 format with object extensions and debug records enabled. You may build the OMF-51
absolute object file by calling the Keil 8051 tools at the command line (e.g. batch file or make file) or by using the
project manager built into the IDE. The default configuration when using the Silicon Laboratories IDE project
manager enables object extension and debug record generation. Refer to Applications Note AN104 - Integrating
Keil 8051 Tools Into the Silicon Laboratories IDE in the “SiLabs\MCU\Documentation\Appnotes” directory on the
CD-ROM for additional information on using the Keil 8051 tools with the Silicon Laboratories IDE.
To build an absolute object file using the Silicon Laboratories IDE project manager, you must first create a project. A
project consists of a set of files, IDE configuration, debug views, and a target build configuration (list of files and tool
configurations used as input to the assembler, compiler, and linker when building an output object file).
The following sections illustrate the steps necessary to manually create a project with one or more source files, build
a program and download the program to the target in preparation for debugging. (The IDE will automatically create a
single-file project using the currently open and active source file if you select Build/Make Project before a project is
defined.)
2
Rev. 0.6
C8051F02x-DK
4.4.1. Creating a New Project
1. Select ProjectNew Project to open a new project and reset all configuration settings to default.
2. Select FileNew File to open an editor window. Create your source file(s) and save the file(s) with a recognized extension, such as .c, .h, or .asm, to enable color syntax highlighting.
3. Right-click on “New Project” in the Project Window. Select Add files to project. Select files in the file
browser and click Open. Continue adding files until all project files have been added.
4. For each of the files in the Project Window that you want assembled, compiled and linked into the target
build, right-click on the file name and select Add file to build. Each file will be assembled or compiled as
appropriate (based on file extension) and linked into the build of the absolute object file.
Note: If a project contains a large number of files, the “Group” feature of the IDE can be used to organize.
Right-click on “New Project” in the Project Window. Select Add Groups to project. Add pre-defined
groups or add customized groups. Right-click on the group name and choose Add file to group. Select files
to be added. Continue adding files until all project files have been added.
4.4.2. Building and Downloading the Program for Debugging
1. Once all source files have been added to the target build, build the project by clicking on the Build/Make
Project button in the toolbar or selecting ProjectBuild/Make Project from the menu.
Note: After the project has been built the first time, the Build/Make Project command will only build the
files that have been changed since the previous build. To rebuild all files and project dependencies, click
on the Rebuild All button in the toolbar or select ProjectRebuild All from the menu.
2. Before connecting to the target device, several connection options may need to be set. Open the
Connection Options window by selecting OptionsConnection Options... in the IDE menu. First, select
the appropriate adapter in the “Serial Adapter” section. Next, the correct “Debug Interface” must be selected.
C8051F02x family devices use the JTAG debug interface. Once all the selections are made, click the OK
button to close the window.
3. Click the Connect button in the toolbar or select DebugConnect from the menu to connect to the device.
4. Download the project to the target by clicking the Download Code button in the toolbar.
Note: To enable automatic downloading if the program build is successful select Enable automatic connect/download after build in the ProjectTarget Build Configuration dialog. If errors occur during the
build process, the IDE will not attempt the download.
5. Save the project when finished with the debug session to preserve the current target build configuration,
editor settings and the location of all open debug views. To save the project, select Project->Save Project
As... from the menu. Create a new name for the project and click on Save.
Rev. 0.6
3
C8051F02x-DK
5. Example Source Code
Example source code and register definition files are provided in the “SiLabs\MCU\Examples\C8051F02x” directory
during IDE installation. These files may be used as a template for code development. Example applications include
a blinking LED example which configures the green LED on the target board to blink at a fixed rate.
5.1. Register Definition Files
Register definition files C8051F020.inc and C8051F020.h define all SFR registers and bit-addressable control/
status bits. They are installed into the “SiLabs\MCU\Examples\C8051F02x” directory during IDE installation. The
register and bit names are identical to those used in the C8051F02x data sheet. Both register definition files are
also installed in the default search path used by the Keil Software 8051 tools. Therefore, when using the Keil 8051
tools included with the development kit (A51, C51), it is not necessary to copy a register definition file to each
project’s file directory.
5.2. Blinking LED Example
The example source files blink.asm and blinky.c show examples of several basic C8051F02x functions. These
include; disabling the watchdog timer (WDT), configuring the Port I/O crossbar, configuring a timer for an interrupt
routine, initializing the system clock, and configuring a GPIO port. When compiled/assembled and linked this program flashes the green LED on the C8051F020 target board about five times a second using the interrupt handler
with a C8051F020 timer.
4
Rev. 0.6
C8051F02x-DK
6. Target Board
The C8051F02x Development Kit includes a target board with a C8051F020 device pre-installed for evaluation and
preliminary software development. Numerous input/output (I/O) connections are provided to facilitate prototyping
using the target board. Refer to Figure 2 for the locations of the various I/O connectors.
Power connector (accepts input from 7 to 15 VDC unregulated power adapter)
Connects SW2 to P3.7 pin
Connects LED D3 to P1.6 pin
JTAG connector for Debug Adapter interface
DB-9 connector for UART0 RS232 interface
Connector for UART0 TX (P0.0)
Connector for UART0 RTS (P4.0)
Connector for UART0 RX (P0.1)
Connector for UART0 CTS (P4.1)
Analog loopback connector
Port 0 - 7 connectors
Analog I/O terminal block
VREF connector
VDD Monitor Disable
96-pin Expansion I/O connector
J5
J24
Port 6
Port 3
Port 4
Port 7
Port 1
Port 0
Port 2
Pin 2
Pin 1
C8051
F02X
J10J8 J6 J9
P3.7 RESET
Port 5
J3
Pin 1 J23
P1.6
J1
Pin 2
J11
J22
Pin 1
JTAG
P1
J1
J3
J4
J5
J6
J8
J9
J10
J11
J12-J19
J20
J22
J23
J24
J4
Pin 2
Pin 1
Pin 1
P1
J20
PWR
Pin 1
Figure 2. C8051F020 Target Board
Rev. 0.6
5
C8051F02x-DK
6.1. System Clock Sources
The C8051F020 device installed on the target board features a calibrated programmable internal oscillator which is
enabled as the system clock source on reset. After reset, the internal oscillator operates at a frequency of 2 MHz
(±2%) by default but may be configured by software to operate at other frequencies. Therefore, in many applications
an external oscillator is not required. However, an external 22.1184 MHz crystal is installed on the target board for
additional applications. Refer to the C8051F02x data sheet for more information on configuring the system clock
source.
6.2. Switches and LEDs
Two switches are provided on the target board. Switch SW1 is connected to the RESET pin of the C8051F020.
Pressing SW1 puts the device into its hardware-reset state. Switch SW2 is connected to the C8051F020’s general
purpose I/O (GPIO) pin through headers. Pressing SW2 generates a logic low signal on the port pin. Remove the
shorting block from the header to disconnect SW2 from the port pins. The port pin signal is also routed to a pin on
the J24 I/O connector. See Table 1 for the port pins and headers corresponding to each switch.
Two LEDs are also provided on the target board. The red LED labeled PWR is used to indicate a power connection
to the target board. The green LED labeled with a port pin name is connected to the C8051F020’s GPIO pin
through headers. Remove the shorting block from the header to disconnect the LED from the port pin. The port pin
signal is also routed to a pin on the J24 I/O connector. See Table 1 for the port pins and headers corresponding to
each LED.
Table 1. Target Board I/O Descriptions
Description
I/O
Header
SW1
SW2
Green LED
Red LED
Reset
P3.7
P1.6
PWR
none
J1
J3
none
6.3. Target Board JTAG Interface (J4)
The JTAG connector (J4) provides access to the JTAG pins of the C8051F020. It is used to connect the Serial
Adapter or the USB Debug Adapter to the target board for in-circuit debugging and Flash programming. Table 2
shows the JTAG pin definitions.
Table 2. JTAG Connector Pin Descriptions
6
Pin #
Description
1
2, 3, 9
4
5
6
7
8, 10
+3 VD (+3.3 VDC)
GND (Ground)
TCK
TMS
TDO
TDI
Not Connected
Rev. 0.6
C8051F02x-DK
6.4. Serial Interface (J5)
A RS232 transceiver circuit and DB-9 (J5) connector are provided on the target board to facilitate serial connections to UART0 of the C8051F020. The TX, RX, RTS and CTS signals of UART0 may be connected to the DB-9
connector and transceiver by installing shorting blocks on headers J6, J8, J9 and J10.
J6
J9
J8
J10
- Install shorting block to connect UART0 TX (P0.0) to the transceiver.
- Install shorting block to connect UART0 RX (P0.1) to the transceiver.
- Install shorting block to connect UART0 RTS (P4.0) to the transceiver.
- Install shorting block to connect UART0 CTS (P4.1) to the transceiver.
6.5. Analog I/O (J11, J20)
Several C8051F020 analog signals are routed to the J20 terminal block and the J11 connector. Header J11 provides the ability to connect DAC0 and DAC1 outputs to several different analog inputs by installing a shorting block
between a DAC output and an analog input on adjacent pins of J11. Refer to Table 3 for J20 terminal block connections and Table 4 for J11 pin definitions.
Table 3. J20 Terminal Block Pin Descriptions
Pin #
Description
1
2
3
4
5
6
7
8
CP0+
CP0DAC0
DAC1
AIN0.0
AIN0.1
VREF0
ADND (Analog Ground)
Table 4. J11 Connector Pin Descriptions
Pin #
Description
1
2
3
4
5
6
7
8
9
10
11
12
CP0+
CP0DAC0
DAC1
CP1+
CP1AIN0.0
AIN0.1
DAC0
DAC1
AIN0.6
AIN0.7
Rev. 0.6
7
C8051F02x-DK
6.6. PORT I/O Connectors (J12 - J19)
In addition to all port I/O signals being routed to the 96-pin expansion connector, each of the eight parallel ports of
the C8051F020 has its own 10-pin header connector. Each connector provides a pin for the corresponding port
pins 0-7, +3.3 VDC and digital ground. Table 5 defines the pins for the port connectors. The same pin-out order is
used for all of the port connectors.
Table 5. J12- J19 Port Connector Pin Descriptions
Pin #
Description
1
2
3
4
5
6
7
8
9
10
Pn.0
Pn.1
Pn.2
Pn.3
Pn.4
Pn.5
Pn.6
Pn.7
+3 VD (+3.3 VDC)
GND (Ground)
6.7. VDD Monitor Disable (J23)
The VDD Monitor of the C8051F020 may be disabled by moving the shorting block on J23 from pins 1-2 to pins 23, as shown in Figure 3.
MONEN
1
2
3
Figure 3. VDD Monitor Hardware Setup
6.8. VREF Connector (J22)
The VREF connector (J22) can be used to connect the VREF (Voltage Reference) output of the C8051F020 to any
(or all) of its voltage reference inputs. Install shorting blocks on J22 in the following manner:
1-2 to connect VREF to VREFD
3-4 to connect VREF to VREF0
5-6 to connect VREF to VREF1
8
Rev. 0.6
C8051F02x-DK
6.9. Expansion I/O Connector (J24)
The 96-pin expansion I/O connector J24 is used to connect daughter boards to the main target board. J24 provides
access to many C8051F020 signal pins. Pins for +3 V, digital ground, analog ground and the unregulated power
supply (VUNREG) are also available. The VUNREG pin is connected directly to the unregulated +V pin of the P1
power connector. See Table 6 for a complete list of pins available at J24.
The J24 socket connector is manufactured by Hirose Electronic Co. Ltd, part number PCN13-96S-2.54DS, DigiKey part number H7096-ND. The corresponding plug connector is also manufactured by Hirose Electronic Co. Ltd,
part number PCN10-96P-2.54DS, Digi-Key part number H5096-ND.
Table 6. J24 Pin Descriptions
Pin #
Description
Pin #
Description
Pin #
Description
A-1
A-2
A-3
A-4
A-5
A-6
A-7
A-8
A-9
A-10
A-11
A-12
A-13
A-14
A-15
A-16
A-17
A-18
A-19
A-20
A-21
A-22
A-23
A-24
A-25
A-26
A-27
A-28
A-29
A-30
A-31
A-32
+3 VD2 (+3.3 VDC)
MONEN
P1.5
P1.2
P2.7
P2.4
P2.1
P3.6
P3.3
P3.0
P0.5
P0.2
P7.7
P7.4
P7.1
P6.6
P6.3
P6.0
P5.5
P5.2
P4.7
P4.4
P4.1
TCK
/RST
AGND (Analog Gnd)
CP1CP0+
VREF0
AIN0.6
AIN0.3
AIN0.0
B-1
B-2
B-3
B-4
B-5
B-6
B-7
B-8
B-9
B-10
B-11
B-12
B-13
B-14
B-15
B-16
B-17
B-18
B-19
B-20
B-21
B-22
B-23
B-24
B-25
B-26
B-27
B-28
B-29
B-30
B-31
B-32
DGND (Digital Gnd)
P1.7
P1.4
P1.1
P2.6
P2.3
P2.0
P3.5
P3.2
P0.7
P0.4
P0.1
P7.6
P7.3
P7.0
P6.5
P6.2
P5.7
P5.4
P5.1
P4.6
P4.3
P4.0
TDI
DGND (Digital Gnd)
DAC1
CP1+
VREF
VREF1
AIN0.5
AIN0.2
AGND (Analog Gnd)
C-1
C-2
C-3
C-4
C-5
C-6
C-7
C-8
C-9
C-10
C-11
C-12
C-13
C-14
C-15
C-16
C-17
C-18
C-19
C-20
C-21
C-22
C-23
C-24
C-25
C-26
C-27
C-28
C-29
C-30
C-31
C-32
XTAL1
P1.6
P1.3
P1.0
P2.5
P2.2
P3.7
P3.4
P3.1
P0.6
P0.3
P0.0
P7.5
P7.2
P6.7
P6.4
P6.1
P5.6
P5.3
P5.0
P4.5
P4.2
TMS
TDO
VUNREG
DAC0
CP0VREFD
AIN0.7
AIN0.4
AIN0.1
AV+ (+3.3 VDC Analog)
Rev. 0.6
9
Figure 4. C8051F020 Target Board Schematic
C8051F02x-DK
7. Schematic
10
Rev. 0.6
C8051F02x-DK
DOCUMENT CHANGE LIST
Revision 0.4 to Revision 0.5
Section 1, added USB Debug Adapter and USB Cable.
Section 2, changed name from "Hardware Setup" to "Hardware Setup using an EC2 Serial Adapter".
Section 2, added 2 Notes bullets.
Section 2, removed Note from bottom of page.
Added Section 3, "Hardware Setup using a USB Debug Adapter".
Section 5.4.2, changed step 2 to include new instructions.
Section 7, J4, changed "Serial Adapter" to "Debug Adapter".
Target Board DEBUG Interface Section, added USB Debug Adapter.
DEBUG Connector Pin Descriptions Table, changed pin 4 to C2D.
Changed "jumper" to "header".
EC2 Serial Adapter section, added EC2 to the section title, table title and figure title.
EC2 Serial Adapter section, changed "JTAG" to "DEBUG".
Added "USB Debug Adapter" section.
Added J8 and J10 to the figure in the Target Board section.
Added J8 and J10 to the connector list.
Revision 0.5 to Revision 0.6
Removed EC2 Serial Adapter from Kit Contents.
Removed Section 2. Hardware Setup using an EC2 Serial Adapter. See RS232 Serial Adapter (EC2) User's
Guide.
Removed Section 8. EC2 Serial Adapter. See RS232 Serial Adapter (EC2) User's Guide.
Removed Section 9. USB Debug Adapter. See USB Debug Adapter User's Guide.
Rev. 0.6
11
Simplicity Studio
One-click access to MCU and
wireless tools, documentation,
software, source code libraries &
more. Available for Windows,
Mac and Linux!
IoT Portfolio
www.silabs.com/IoT
SW/HW
Quality
Support and Community
www.silabs.com/simplicity
www.silabs.com/quality
community.silabs.com
Disclaimer
Silicon Laboratories intends to provide customers with the latest, accurate, and in-depth documentation of all peripherals and modules available for system and software implementers
using or intending to use the Silicon Laboratories products. Characterization data, available modules and peripherals, memory sizes and memory addresses refer to each specific
device, and "Typical" parameters provided can and do vary in different applications. Application examples described herein are for illustrative purposes only. Silicon Laboratories
reserves the right to make changes without further notice and limitation to product information, specifications, and descriptions herein, and does not give warranties as to the accuracy
or completeness of the included information. Silicon Laboratories shall have no liability for the consequences of use of the information supplied herein. This document does not imply
or express copyright licenses granted hereunder to design or fabricate any integrated circuits. The products must not be used within any Life Support System without the specific
written consent of Silicon Laboratories. A "Life Support System" is any product or system intended to support or sustain life and/or health, which, if it fails, can be reasonably expected
to result in significant personal injury or death. Silicon Laboratories products are generally not intended for military applications. Silicon Laboratories products shall under no
circumstances be used in weapons of mass destruction including (but not limited to) nuclear, biological or chemical weapons, or missiles capable of delivering such weapons.
Trademark Information
Silicon Laboratories Inc., Silicon Laboratories, Silicon Labs, SiLabs and the Silicon Labs logo, CMEMS®, EFM, EFM32, EFR, Energy Micro, Energy Micro logo and combinations
thereof, "the world’s most energy friendly microcontrollers", Ember®, EZLink®, EZMac®, EZRadio®, EZRadioPRO®, DSPLL®, ISOmodem ®, Precision32®, ProSLIC®, SiPHY®,
USBXpress® and others are trademarks or registered trademarks of Silicon Laboratories Inc. ARM, CORTEX, Cortex-M3 and THUMB are trademarks or registered trademarks of
ARM Holdings. Keil is a registered trademark of ARM Limited. All other products or brand names mentioned herein are trademarks of their respective holders.
Silicon Laboratories Inc.
400 West Cesar Chavez
Austin, TX 78701
USA
http://www.silabs.com
工商网监
湘ICP备2023018690号
