C8051F38B-B-GQ

C8051F388/9/A/B Flash MCU Family Analog Peripherals - 10-Bit ADC • Up to 500 ksps • Built-in analog multiplexer with single-ended and • • • differential mode VREF from external pin, internal reference, or VDD Built-in temperature sensor External conversion start input option - Two comparators - Internal voltage reference - Brown-out detector and POR Circuitry On-Chip Debug - On-chip debug circuitry facilitates full speed, non-intru- sive in-system debug (No emulator required) Provides breakpoints, single stepping, inspect/modify memory and registers Superior performance to emulation systems using ICE-chips, target pods, and sockets Voltage Supply Input: 2.7 to 5.25 V - Voltages from 2.7 to 5.25 V supported using On-Chip Voltage Regulators High Speed 8051 μC Core - Pipelined instruction architecture; executes 70% of - instructions in 1 or 2 system clocks Up to 48 MIPS operation Expanded interrupt handler Rev. 1.2 6/19 Memory - 4352 or 2304 Bytes RAM - 64 or 32 kB Flash; In-system programmable in 512-byte sectors Digital Peripherals - 40/25 Port I/O; All 5 V tolerant with high sink current - Hardware enhanced SPI™, two I2C/SMBus™, and two - enhanced UART serial ports Six general purpose 16-bit counter/timers 16-bit programmable counter array (PCA) with five capture/compare modules External Memory Interface (EMIF) Clock Sources - Internal Oscillator: ±1.5% accuracy. Supports all UART - modes External Oscillator: Crystal, RC, C, or clock (1 or 2 Pin modes) Low Frequency (80 kHz) Internal Oscillator Can switch between clock sources on-the-fly Packages - 48-pin TQFP (C8051F388/A) - 32-pin LQFP (C8051F389/B) - 5x5 mm 32-pin QFN (C8051F389/B) Temperature Range: –40 to +85 °C Copyright © 2019 by Silicon Laboratories C8051F388/9/A/B 2 Rev. 1.2 C8051F388/9/A/B Table of Contents 1. System Overview ..................................................................................................... 15 2. C8051F34x Compatibility ........................................................................................ 19 2.1. Hardware Incompatibilities ................................................................................ 20 3. Pinout and Package Definitions ............................................................................. 21 4. Typical Connection Diagrams ................................................................................ 33 4.1. Power ............................................................................................................ 33 5. Electrical Characteristics ........................................................................................ 34 5.1. Absolute Maximum Specifications..................................................................... 34 5.2. Electrical Characteristics ................................................................................... 35 6. 10-Bit ADC ................................................................................................................ 42 6.1. Output Code Formatting .................................................................................... 43 6.3. Modes of Operation ........................................................................................... 46 6.3.1. Starting a Conversion................................................................................ 46 6.3.2. Tracking Modes......................................................................................... 47 6.3.3. Settling Time Requirements...................................................................... 48 6.4. Programmable Window Detector....................................................................... 52 6.4.1. Window Detector Example........................................................................ 54 6.5. ADC0 Analog Multiplexer .................................................................................. 55 7. Voltage Reference Options ..................................................................................... 58 8. Comparator0 and Comparator1.............................................................................. 60 8.1. Comparator Multiplexers ................................................................................... 67 9. Voltage Regulators (REG0 and REG1)................................................................... 70 9.1. Voltage Regulator (REG0)................................................................................. 70 9.1.1. Regulator Mode Selection......................................................................... 70 9.1.2. External Interrupt 2 (INT2) ........................................................................ 70 9.2. Voltage Regulator (REG1)................................................................................. 70 10. Power Management Modes................................................................................... 72 10.1. Idle Mode......................................................................................................... 72 10.2. Stop Mode ....................................................................................................... 73 10.3. Suspend Mode ................................................................................................ 73 11. CIP-51 Microcontroller........................................................................................... 75 11.1. Instruction Set.................................................................................................. 76 11.1.1. Instruction and CPU Timing .................................................................... 76 11.2. CIP-51 Register Descriptions .......................................................................... 81 12. Prefetch Engine...................................................................................................... 84 13. Memory Organization ............................................................................................ 85 13.1. Program Memory............................................................................................. 86 13.2. Data Memory ................................................................................................... 86 13.3. General Purpose Registers ............................................................................. 87 13.4. Bit Addressable Locations ............................................................................... 87 13.5. Stack ............................................................................................................ 87 14. External Data Memory Interface and On-Chip XRAM ......................................... 88 14.1. Accessing XRAM............................................................................................. 88 Rev. 1.2 3 C8051F388/9/A/B 14.1.1. 16-Bit MOVX Example ............................................................................ 88 14.1.2. 8-Bit MOVX Example .............................................................................. 88 14.2. Configuring the External Memory Interface ..................................................... 89 14.3. Port Configuration............................................................................................ 89 14.4. Multiplexed and Non-multiplexed Selection..................................................... 92 14.4.1. Multiplexed Configuration........................................................................ 92 14.4.2. Non-multiplexed Configuration................................................................ 93 14.5. Memory Mode Selection.................................................................................. 94 14.5.1. Internal XRAM Only ................................................................................ 94 14.5.2. Split Mode without Bank Select............................................................... 94 14.5.3. Split Mode with Bank Select.................................................................... 95 14.5.4. External Only........................................................................................... 95 14.6. Timing ............................................................................................................ 96 14.6.1. Non-multiplexed Mode ............................................................................ 98 14.6.1.1. 16-bit MOVX: EMI0CF[4:2] = 101, 110, or 111............................... 98 14.6.1.2. 8-bit MOVX without Bank Select: EMI0CF[4:2] = 101 or 111 ......... 99 14.6.1.3. 8-bit MOVX with Bank Select: EMI0CF[4:2] = 110 ....................... 100 14.6.2. Multiplexed Mode .................................................................................. 101 14.6.2.1. 16-bit MOVX: EMI0CF[4:2] = 001, 010, or 011............................. 101 14.6.2.2. 8-bit MOVX without Bank Select: EMI0CF[4:2] = 001 or 011 ....... 102 14.6.2.3. 8-bit MOVX with Bank Select: EMI0CF[4:2] = 010 ....................... 103 15. Special Function Registers................................................................................. 105 15.1. SFR Paging ................................................................................................... 105 16. Interrupts .............................................................................................................. 112 16.1. MCU Interrupt Sources and Vectors.............................................................. 113 16.1.1. Interrupt Priorities.................................................................................. 113 16.1.2. Interrupt Latency ................................................................................... 113 16.2. Interrupt Register Descriptions ...................................................................... 113 16.3. INT0 and INT1 External Interrupt Sources .................................................... 121 17. Reset Sources ...................................................................................................... 123 17.1. Power-On Reset ............................................................................................ 124 17.2. Power-Fail Reset / VDD Monitor ................................................................... 125 17.3. External Reset ............................................................................................... 126 17.4. Missing Clock Detector Reset ....................................................................... 126 17.5. Comparator0 Reset ....................................................................................... 126 17.6. PCA Watchdog Timer Reset ......................................................................... 127 17.7. Flash Error Reset .......................................................................................... 127 17.8. Software Reset .............................................................................................. 127 18. Flash Memory....................................................................................................... 129 18.1. Programming The Flash Memory .................................................................. 129 18.1.1. Flash Lock and Key Functions .............................................................. 129 18.1.2. Flash Erase Procedure ......................................................................... 129 18.1.3. Flash Write Procedure .......................................................................... 130 18.2. Non-Volatile Data Storage............................................................................. 131 18.3. Security Options ............................................................................................ 131 4 Rev. 1.2 C8051F388/9/A/B 19. Oscillators and Clock Selection ......................................................................... 136 19.1. System Clock Selection................................................................................. 137 19.2. Programmable Internal High-Frequency (H-F) Oscillator .............................. 139 19.2.1. Internal Oscillator Suspend Mode ......................................................... 139 19.3. Clock Multiplier .............................................................................................. 141 19.4. Programmable Internal Low-Frequency (L-F) Oscillator ............................... 142 19.4.1. Calibrating the Internal L-F Oscillator.................................................... 142 19.5. External Oscillator Drive Circuit..................................................................... 143 19.5.1. External Crystal Mode........................................................................... 143 19.5.2. External RC Example............................................................................ 145 19.5.3. External Capacitor Example.................................................................. 145 20. Port Input/Output ................................................................................................. 147 20.1. Priority Crossbar Decoder ............................................................................. 148 20.2. Port I/O Initialization ...................................................................................... 152 20.3. General Purpose Port I/O .............................................................................. 155 21. SMBus0 and SMBus1 (I2C Compatible)............................................................. 166 21.1. Supporting Documents .................................................................................. 167 21.2. SMBus Configuration..................................................................................... 167 21.3. SMBus Operation .......................................................................................... 167 21.3.1. Transmitter Vs. Receiver....................................................................... 168 21.3.2. Arbitration.............................................................................................. 168 21.3.3. Clock Low Extension............................................................................. 168 21.3.4. SCL Low Timeout.................................................................................. 168 21.3.5. SCL High (SMBus Free) Timeout ......................................................... 169 21.4. Using the SMBus........................................................................................... 169 21.4.1. SMBus Configuration Register.............................................................. 169 21.4.2. SMBus Timing Control Register............................................................ 171 21.4.3. SMBnCN Control Register .................................................................... 175 21.4.3.1. Software ACK Generation ............................................................ 175 21.4.3.2. Hardware ACK Generation ........................................................... 175 21.4.4. Hardware Slave Address Recognition .................................................. 178 21.4.5. Data Register ........................................................................................ 182 21.5. SMBus Transfer Modes................................................................................. 184 21.5.1. Write Sequence (Master) ...................................................................... 184 21.5.2. Read Sequence (Master) ...................................................................... 185 21.5.3. Write Sequence (Slave) ........................................................................ 186 21.5.4. Read Sequence (Slave) ........................................................................ 187 21.6. SMBus Status Decoding................................................................................ 187 22. UART0 ................................................................................................................... 193 22.1. Enhanced Baud Rate Generation.................................................................. 194 22.2. Operational Modes ........................................................................................ 195 22.2.1. 8-Bit UART ............................................................................................ 195 22.2.2. 9-Bit UART ............................................................................................ 196 22.3. Multiprocessor Communications ................................................................... 197 23. UART1 ................................................................................................................... 201 Rev. 1.2 5 C8051F388/9/A/B 23.1. Baud Rate Generator .................................................................................... 202 23.2. Data Format................................................................................................... 203 23.3. Configuration and Operation ......................................................................... 204 23.3.1. Data Transmission ................................................................................ 204 23.3.2. Data Reception ..................................................................................... 204 23.3.3. Multiprocessor Communications ........................................................... 205 24. Enhanced Serial Peripheral Interface (SPI0) ..................................................... 211 24.1. Signal Descriptions........................................................................................ 212 24.1.1. Master Out, Slave In (MOSI)................................................................. 212 24.1.2. Master In, Slave Out (MISO)................................................................. 212 24.1.3. Serial Clock (SCK) ................................................................................ 212 24.1.4. Slave Select (NSS) ............................................................................... 212 24.2. SPI0 Master Mode Operation ........................................................................ 212 24.3. SPI0 Slave Mode Operation .......................................................................... 214 24.4. SPI0 Interrupt Sources .................................................................................. 215 24.5. Serial Clock Phase and Polarity .................................................................... 215 24.6. SPI Special Function Registers ..................................................................... 217 25. Timers ................................................................................................................... 224 25.1. Timer 0 and Timer 1 ...................................................................................... 227 25.1.1. Mode 0: 13-bit Counter/Timer ............................................................... 227 25.1.2. Mode 1: 16-bit Counter/Timer ............................................................... 228 25.1.3. Mode 2: 8-bit Counter/Timer with Auto-Reload..................................... 228 25.1.4. Mode 3: Two 8-bit Counter/Timers (Timer 0 Only)................................ 229 25.2. Timer 2 .......................................................................................................... 235 25.2.1. 16-bit Timer with Auto-Reload............................................................... 235 25.2.2. 8-bit Timers with Auto-Reload............................................................... 236 25.2.3. Timer 2 Capture Modes: LFO Falling Edge .......................................... 236 25.3. Timer 3 .......................................................................................................... 242 25.3.1. 16-bit Timer with Auto-Reload............................................................... 242 25.3.2. 8-bit Timers with Auto-Reload............................................................... 243 25.3.3. Timer 3 Capture Modes: LFO Falling Edge .......................................... 243 25.4. Timer 4 .......................................................................................................... 249 25.4.1. 16-bit Timer with Auto-Reload............................................................... 249 25.4.2. 8-bit Timers with Auto-Reload............................................................... 250 25.5. Timer 5 .......................................................................................................... 254 25.5.1. 16-bit Timer with Auto-Reload............................................................... 254 25.5.2. 8-bit Timers with Auto-Reload............................................................... 255 26. Programmable Counter Array............................................................................. 259 26.1. PCA Counter/Timer ....................................................................................... 260 26.2. PCA0 Interrupt Sources................................................................................. 261 26.3. Capture/Compare Modules ........................................................................... 262 26.3.1. Edge-triggered Capture Mode............................................................... 263 26.3.2. Software Timer (Compare) Mode.......................................................... 264 26.3.3. High-Speed Output Mode ..................................................................... 265 26.3.4. Frequency Output Mode ....................................................................... 266 6 Rev. 1.2 C8051F388/9/A/B 26.3.5. 8-bit Pulse Width Modulator Mode ....................................................... 267 26.3.6. 16-Bit Pulse Width Modulator Mode..................................................... 268 26.4. Watchdog Timer Mode .................................................................................. 269 26.4.1. Watchdog Timer Operation ................................................................... 269 26.4.2. Watchdog Timer Usage ........................................................................ 270 26.5. Register Descriptions for PCA0..................................................................... 272 27. C2 Interface .......................................................................................................... 277 27.1. C2 Interface Registers................................................................................... 277 27.2. C2 Pin Sharing .............................................................................................. 280 28. Revision Specific Behavior................................................................................. 281 28.1. Revision Identification.................................................................................... 281 28.2. INT2 Pin Not Connected................................................................................ 283 Document Change List.............................................................................................. 284 Contact Information................................................................................................... 285 Rev. 1.2 7 C8051F388/9/A/B List of Figures Figure 1.1. C8051F388/A Block Diagram ................................................................ 17 Figure 1.2. C8051F389/B Block Diagram ................................................................ 18 Figure 3.1. TQFP-48 (C8051F388/A) Pinout Diagram (Top View) .......................... 24 Figure 3.2. TQFP-48 Package Diagram .................................................................. 25 Figure 3.3. TQFP-48 Recommended PCB Land Pattern ........................................ 26 Figure 3.4. LQFP-32 (C8051F389/B) Pinout Diagram (Top View) .......................... 27 Figure 3.5. LQFP-32 Package Diagram .................................................................. 28 Figure 3.6. LQFP-32 Recommended PCB Land Pattern ........................................ 29 Figure 3.7. QFN-32 (C8051F389/B) Pinout Diagram (Top View) ............................ 30 Figure 3.8. QFN-32 Package Drawing .................................................................... 31 Figure 3.9. QFN-32 Recommended PCB Land Pattern .......................................... 32 Figure 4.1. Connection Diagram with Voltage Regulator Used ............................... 33 Figure 4.2. Connection Diagram with Voltage Regulator Not Used ........................ 33 Figure 6.1. ADC0 Functional Block Diagram ........................................................... 42 Figure 6.2. Typical Temperature Sensor Transfer Function .................................... 44 Figure 6.3. Temperature Sensor Error with 1-Point Calibration .............................. 45 Figure 6.4. 10-Bit ADC Track and Conversion Example Timing ............................. 47 Figure 6.5. ADC0 Equivalent Input Circuits ............................................................. 48 Figure 6.6. ADC Window Compare Example: Right-Justified Data ......................... 54 Figure 6.7. ADC Window Compare Example: Left-Justified Data ........................... 54 Figure 7.1. Voltage Reference Functional Block Diagram ....................................... 58 Figure 8.1. Comparator0 Functional Block Diagram ............................................... 60 Figure 8.2. Comparator1 Functional Block Diagram ............................................... 61 Figure 8.3. Comparator Hysteresis Plot .................................................................. 62 Figure 8.4. Comparator Input Multiplexer Block Diagram ........................................ 67 Figure 11.1. CIP-51 Block Diagram ......................................................................... 75 Figure 13.1. On-Chip Memory Map for 64 kB Devices (C8051F388/9) ................... 85 Figure 13.2. On-Chip Memory Map for 32 kB Devices (C8051F38A/B) .................. 86 Figure 14.1. Multiplexed Configuration Example ..................................................... 92 Figure 14.2. Non-multiplexed Configuration Example ............................................. 93 Figure 14.3. EMIF Operating Modes ....................................................................... 94 Figure 14.4. Non-Multiplexed 16-bit MOVX Timing ................................................. 98 Figure 14.5. Non-Multiplexed 8-bit MOVX without Bank Select Timing .................. 99 Figure 14.6. Non-Multiplexed 8-bit MOVX with Bank Select Timing ..................... 100 Figure 14.7. Multiplexed 16-bit MOVX Timing ....................................................... 101 Figure 14.8. Multiplexed 8-bit MOVX without Bank Select Timing ........................ 102 Figure 14.9. Multiplexed 8-bit MOVX with Bank Select Timing ............................. 103 Figure 17.1. Reset Sources ................................................................................... 123 Figure 17.2. Power-On and VDD Monitor Reset Timing ....................................... 124 Figure 18.1. Flash Program Memory Map and Security Byte ................................ 131 Figure 19.1. Oscillator Options .............................................................................. 136 Figure 19.2. External Crystal Example .................................................................. 144 Figure 20.1. Port I/O Functional Block Diagram (Port 0 through Port 3) ............... 147 8 Rev. 1.2 C8051F388/9/A/B Figure 20.2. Port I/O Cell Block Diagram .............................................................. 148 Figure 20.3. Peripheral Availability on Port I/O Pins .............................................. 149 Figure 20.4. Crossbar Priority Decoder in Example Configuration (No Pins Skipped) ............................................................................................ 150 Figure 20.5. Crossbar Priority Decoder in Example Configuration (3 Pins Skipped) ............................................................................................... 151 Figure 21.1. SMBus Block Diagram ...................................................................... 166 Figure 21.2. Typical SMBus Configuration ............................................................ 167 Figure 21.3. SMBus Transaction ........................................................................... 168 Figure 21.4. Typical SMBus SCL Generation ........................................................ 170 Figure 21.5. Typical Master Write Sequence ........................................................ 184 Figure 21.6. Typical Master Read Sequence ........................................................ 185 Figure 21.7. Typical Slave Write Sequence .......................................................... 186 Figure 21.8. Typical Slave Read Sequence .......................................................... 187 Figure 22.1. UART0 Block Diagram ...................................................................... 193 Figure 22.2. UART0 Baud Rate Logic ................................................................... 194 Figure 22.3. UART Interconnect Diagram ............................................................. 195 Figure 22.4. 8-Bit UART Timing Diagram .............................................................. 195 Figure 22.5. 9-Bit UART Timing Diagram .............................................................. 196 Figure 22.6. UART Multi-Processor Mode Interconnect Diagram ......................... 197 Figure 23.1. UART1 Block Diagram ...................................................................... 201 Figure 23.2. UART1 Timing Without Parity or Extra Bit ......................................... 203 Figure 23.3. UART1 Timing With Parity ................................................................ 203 Figure 23.4. UART1 Timing With Extra Bit ............................................................ 203 Figure 23.5. Typical UART Interconnect Diagram ................................................. 204 Figure 23.6. UART Multi-Processor Mode Interconnect Diagram ......................... 205 Figure 24.1. SPI Block Diagram ............................................................................ 211 Figure 24.2. Multiple-Master Mode Connection Diagram ...................................... 213 Figure 24.3. 3-Wire Single Master and 3-Wire Single Slave Mode Connection Diagram ........................................................................................ 213 Figure 24.4. 4-Wire Single Master Mode and 4-Wire Slave Mode Connection Diagram ........................................................................................ 214 Figure 24.5. Master Mode Data/Clock Timing ....................................................... 216 Figure 24.6. Slave Mode Data/Clock Timing (CKPHA = 0) ................................... 216 Figure 24.7. Slave Mode Data/Clock Timing (CKPHA = 1) ................................... 217 Figure 24.8. SPI Master Timing (CKPHA = 0) ....................................................... 221 Figure 24.9. SPI Master Timing (CKPHA = 1) ....................................................... 221 Figure 24.10. SPI Slave Timing (CKPHA = 0) ....................................................... 222 Figure 24.11. SPI Slave Timing (CKPHA = 1) ....................................................... 222 Figure 25.1. T0 Mode 0 Block Diagram ................................................................. 228 Figure 25.2. T0 Mode 2 Block Diagram ................................................................. 229 Figure 25.3. T0 Mode 3 Block Diagram ................................................................. 230 Figure 25.4. Timer 2 16-Bit Mode Block Diagram ................................................. 235 Figure 25.5. Timer 2 8-Bit Mode Block Diagram ................................................... 236 Figure 25.6. Timer 2 Capture Mode (T2SPLIT = 0) ............................................... 237 Rev. 1.2 9 C8051F388/9/A/B Figure 25.7. Timer 2 Capture Mode (T2SPLIT = 0) ............................................... 238 Figure 25.8. Timer 3 16-Bit Mode Block Diagram ................................................. 242 Figure 25.9. Timer 3 8-Bit Mode Block Diagram ................................................... 243 Figure 25.10. Timer 3 Capture Mode (T3SPLIT = 0) ............................................. 244 Figure 25.11. Timer 3 Capture Mode (T3SPLIT = 0) ............................................. 245 Figure 25.12. Timer 4 16-Bit Mode Block Diagram ............................................... 249 Figure 25.13. Timer 4 8-Bit Mode Block Diagram ................................................. 250 Figure 25.14. Timer 5 16-Bit Mode Block Diagram ............................................... 254 Figure 25.15. Timer 5 8-Bit Mode Block Diagram ................................................. 255 Figure 26.1. PCA Block Diagram ........................................................................... 259 Figure 26.2. PCA Counter/Timer Block Diagram ................................................... 260 Figure 26.3. PCA Interrupt Block Diagram ............................................................ 261 Figure 26.4. PCA Capture Mode Diagram ............................................................. 263 Figure 26.5. PCA Software Timer Mode Diagram ................................................. 264 Figure 26.6. PCA High-Speed Output Mode Diagram ........................................... 265 Figure 26.7. PCA Frequency Output Mode ........................................................... 266 Figure 26.8. PCA 8-Bit PWM Mode Diagram ........................................................ 267 Figure 26.9. PCA 16-Bit PWM Mode ..................................................................... 268 Figure 26.10. PCA Module 4 with Watchdog Timer Enabled ................................ 269 Figure 27.1. Typical C2 Pin Sharing ...................................................................... 280 10 Rev. 1.2 C8051F388/9/A/B List of Tables Table 1.1. Product Selection Guide ......................................................................... 16 Table 2.1. C8051F388/9/A/B Replacement Part Numbers ...................................... 19 Table 3.1. Pin Definitions for the C8051F388/9/A/B ................................................ 21 Table 3.2. TQFP-48 Package Dimensions .............................................................. 25 Table 3.3. TQFP-48 PCB Land Pattern Dimensions ............................................... 26 Table 3.4. LQFP-32 Package Dimensions .............................................................. 28 Table 3.5. LQFP-32 PCB Land Pattern Dimensions ............................................... 29 Table 3.6. QFN-32 Package Dimensions ................................................................ 31 Table 3.7. QFN-32 PCB Land Pattern Dimensions ................................................. 32 Table 5.1. Absolute Maximum Ratings .................................................................... 34 Table 5.2. Global Electrical Characteristics ............................................................. 35 Table 5.3. Port I/O DC Electrical Characteristics ..................................................... 36 Table 5.4. Reset Electrical Characteristics .............................................................. 36 Table 5.5. Internal Voltage Regulator Electrical Characteristics ............................. 37 Table 5.6. Flash Electrical Characteristics .............................................................. 37 Table 5.7. Internal High-Frequency Oscillator Electrical Characteristics ................. 38 Table 5.8. Internal Low-Frequency Oscillator Electrical Characteristics ................. 38 Table 5.9. External Oscillator Electrical Characteristics .......................................... 38 Table 5.10. ADC0 Electrical Characteristics ............................................................ 39 Table 5.11. Temperature Sensor Electrical Characteristics .................................... 40 Table 5.12. Voltage Reference Electrical Characteristics ....................................... 40 Table 5.13. Comparator Electrical Characteristics .................................................. 41 Table 11.1. CIP-51 Instruction Set Summary .......................................................... 77 Table 14.1. AC Parameters for External Memory Interface ................................... 104 Table 15.1. Special Function Register (SFR) Memory Map .................................. 106 Table 15.2. Special Function Registers ................................................................. 107 Table 16.1. Interrupt Summary .............................................................................. 114 Table 21.1. SMBus Clock Source Selection .......................................................... 170 Table 21.2. Minimum SDA Setup and Hold Times ................................................ 171 Table 21.3. Sources for Hardware Changes to SMBnCN ..................................... 178 Table 21.4. Hardware Address Recognition Examples (EHACK = 1) ................... 179 Table 21.5. SMBus Status Decoding: Hardware ACK Disabled (EHACK = 0) ...... 188 Table 21.6. SMBus Status Decoding: Hardware ACK Enabled (EHACK = 1) ...... 190 Table 22.1. Timer Settings for Standard Baud Rates Using Internal Oscillator ..... 199 Table 23.1. Baud Rate Generator Settings for Standard Baud Rates ................... 202 Table 24.1. SPI Slave Timing Parameters ............................................................ 223 Table 26.1. PCA Timebase Input Options ............................................................. 260 Table 26.2. PCA0CPM Bit Settings for PCA Capture/Compare Modules ............. 262 Table 26.3. Watchdog Timer Timeout Intervals1 ................................................... 271 Rev. 1.2 11 C8051F388/9/A/B List of Registers SFR Definition 6.1. ADC0CF: ADC0 Configuration ...................................................... 49 SFR Definition 6.2. ADC0H: ADC0 Data Word MSB .................................................... 50 SFR Definition 6.3. ADC0L: ADC0 Data Word LSB ...................................................... 50 SFR Definition 6.4. ADC0CN: ADC0 Control ................................................................ 51 SFR Definition 6.5. ADC0GTH: ADC0 Greater-Than Data High Byte .......................... 52 SFR Definition 6.6. ADC0GTL: ADC0 Greater-Than Data Low Byte ............................ 52 SFR Definition 6.7. ADC0LTH: ADC0 Less-Than Data High Byte ................................ 53 SFR Definition 6.8. ADC0LTL: ADC0 Less-Than Data Low Byte ................................. 53 SFR Definition 6.9. AMX0P: AMUX0 Positive Channel Select ..................................... 56 SFR Definition 6.10. AMX0N: AMUX0 Negative Channel Select ................................. 57 SFR Definition 7.1. REF0CN: Reference Control ......................................................... 59 SFR Definition 8.1. CPT0CN: Comparator0 Control ..................................................... 63 SFR Definition 8.2. CPT0MD: Comparator0 Mode Selection ....................................... 64 SFR Definition 8.3. CPT1CN: Comparator1 Control ..................................................... 65 SFR Definition 8.4. CPT1MD: Comparator1 Mode Selection ....................................... 66 SFR Definition 8.5. CPT0MX: Comparator0 MUX Selection ........................................ 68 SFR Definition 8.6. CPT1MX: Comparator1 MUX Selection ........................................ 69 SFR Definition 9.1. REG01CN: Voltage Regulator Control .......................................... 71 SFR Definition 10.1. PCON: Power Control .................................................................. 74 SFR Definition 11.1. DPL: Data Pointer Low Byte ........................................................ 81 SFR Definition 11.2. DPH: Data Pointer High Byte ....................................................... 81 SFR Definition 11.3. SP: Stack Pointer ......................................................................... 82 SFR Definition 11.4. ACC: Accumulator ....................................................................... 82 SFR Definition 11.5. B: B Register ................................................................................ 82 SFR Definition 11.6. PSW: Program Status Word ........................................................ 83 SFR Definition 12.1. PFE0CN: Prefetch Engine Control .............................................. 84 SFR Definition 14.1. EMI0CN: External Memory Interface Control .............................. 90 SFR Definition 14.2. EMI0CF: External Memory Interface Configuration ..................... 91 SFR Definition 14.3. EMI0TC: External Memory Timing Control .................................. 97 SFR Definition 15.1. SFRPAGE: SFR Page ............................................................... 105 SFR Definition 16.1. IE: Interrupt Enable .................................................................... 115 SFR Definition 16.2. IP: Interrupt Priority .................................................................... 116 SFR Definition 16.3. EIE1: Extended Interrupt Enable 1 ............................................ 117 SFR Definition 16.4. EIP1: Extended Interrupt Priority 1 ............................................ 118 SFR Definition 16.5. EIE2: Extended Interrupt Enable 2 ............................................ 119 SFR Definition 16.6. EIP2: Extended Interrupt Priority 2 ............................................ 120 SFR Definition 16.7. IT01CF: INT0/INT1 ConfigurationO ........................................... 122 SFR Definition 17.1. VDM0CN: VDD Monitor Control ................................................ 126 SFR Definition 17.2. RSTSRC: Reset Source ............................................................ 128 SFR Definition 18.1. PSCTL: Program Store R/W Control ......................................... 133 SFR Definition 18.2. FLKEY: Flash Lock and Key ...................................................... 134 SFR Definition 18.3. FLSCL: Flash Scale ................................................................... 135 SFR Definition 19.1. CLKSEL: Clock Select ............................................................... 138 12 Rev. 1.2 C8051F388/9/A/B SFR Definition 19.2. OSCICL: Internal H-F Oscillator Calibration .............................. 139 SFR Definition 19.3. OSCICN: Internal H-F Oscillator Control ................................... 140 SFR Definition 19.4. CLKMUL: Clock Multiplier Control ............................................. 141 SFR Definition 19.5. OSCLCN: Internal L-F Oscillator Control ................................... 142 SFR Definition 19.6. OSCXCN: External Oscillator Control ........................................ 146 SFR Definition 20.1. XBR0: Port I/O Crossbar Register 0 .......................................... 153 SFR Definition 20.2. XBR1: Port I/O Crossbar Register 1 .......................................... 154 SFR Definition 20.3. XBR2: Port I/O Crossbar Register 2 .......................................... 155 SFR Definition 20.4. P0: Port 0 ................................................................................... 156 SFR Definition 20.5. P0MDIN: Port 0 Input Mode ....................................................... 156 SFR Definition 20.6. P0MDOUT: Port 0 Output Mode ................................................ 157 SFR Definition 20.7. P0SKIP: Port 0 Skip ................................................................... 157 SFR Definition 20.8. P1: Port 1 ................................................................................... 158 SFR Definition 20.9. P1MDIN: Port 1 Input Mode ....................................................... 158 SFR Definition 20.10. P1MDOUT: Port 1 Output Mode .............................................. 159 SFR Definition 20.11. P1SKIP: Port 1 Skip ................................................................. 159 SFR Definition 20.12. P2: Port 2 ................................................................................. 160 SFR Definition 20.13. P2MDIN: Port 2 Input Mode ..................................................... 160 SFR Definition 20.14. P2MDOUT: Port 2 Output Mode .............................................. 161 SFR Definition 20.15. P2SKIP: Port 2 Skip ................................................................. 161 SFR Definition 20.16. P3: Port 3 ................................................................................. 162 SFR Definition 20.17. P3MDIN: Port 3 Input Mode ..................................................... 162 SFR Definition 20.18. P3MDOUT: Port 3 Output Mode .............................................. 163 SFR Definition 20.19. P3SKIP: Port 3 Skip ................................................................. 163 SFR Definition 20.20. P4: Port 4 ................................................................................. 164 SFR Definition 20.21. P4MDIN: Port 4 Input Mode ..................................................... 164 SFR Definition 20.22. P4MDOUT: Port 4 Output Mode .............................................. 165 SFR Definition 21.1. SMB0CF: SMBus Clock/Configuration ...................................... 172 SFR Definition 21.2. SMB1CF: SMBus Clock/Configuration ...................................... 173 SFR Definition 21.3. SMBTC: SMBus Timing Control ................................................ 174 SFR Definition 21.4. SMB0CN: SMBus Control .......................................................... 176 SFR Definition 21.5. SMB1CN: SMBus Control .......................................................... 177 SFR Definition 21.6. SMB0ADR: SMBus0 Slave Address .......................................... 179 SFR Definition 21.7. SMB0ADM: SMBus0 Slave Address Mask ................................ 180 SFR Definition 21.8. SMB1ADR: SMBus1 Slave Address .......................................... 180 SFR Definition 21.9. SMB1ADM: SMBus1 Slave Address Mask ................................ 181 SFR Definition 21.10. SMB0DAT: SMBus Data .......................................................... 182 SFR Definition 21.11. SMB1DAT: SMBus Data .......................................................... 183 SFR Definition 22.1. SCON0: Serial Port 0 Control .................................................... 198 SFR Definition 22.2. SBUF0: Serial (UART0) Port Data Buffer .................................. 199 SFR Definition 23.1. SCON1: UART1 Control ............................................................ 206 SFR Definition 23.2. SMOD1: UART1 Mode .............................................................. 207 SFR Definition 23.3. SBUF1: UART1 Data Buffer ...................................................... 208 SFR Definition 23.4. SBCON1: UART1 Baud Rate Generator Control ...................... 209 SFR Definition 23.5. SBRLH1: UART1 Baud Rate Generator High Byte ................... 209 Rev. 1.2 13 C8051F388/9/A/B SFR Definition 23.6. SBRLL1: UART1 Baud Rate Generator Low Byte ..................... 210 SFR Definition 24.1. SPI0CFG: SPI0 Configuration ................................................... 218 SFR Definition 24.2. SPI0CN: SPI0 Control ............................................................... 219 SFR Definition 24.3. SPI0CKR: SPI0 Clock Rate ....................................................... 220 SFR Definition 24.4. SPI0DAT: SPI0 Data ................................................................. 220 SFR Definition 25.1. CKCON: Clock Control .............................................................. 225 SFR Definition 25.2. CKCON1: Clock Control 1 ......................................................... 226 SFR Definition 25.3. TCON: Timer Control ................................................................. 231 SFR Definition 25.4. TMOD: Timer Mode ................................................................... 232 SFR Definition 25.5. TL0: Timer 0 Low Byte ............................................................... 233 SFR Definition 25.6. TL1: Timer 1 Low Byte ............................................................... 233 SFR Definition 25.7. TH0: Timer 0 High Byte ............................................................. 234 SFR Definition 25.8. TH1: Timer 1 High Byte ............................................................. 234 SFR Definition 25.9. TMR2CN: Timer 2 Control ......................................................... 239 SFR Definition 25.10. TMR2RLL: Timer 2 Reload Register Low Byte ........................ 240 SFR Definition 25.11. TMR2RLH: Timer 2 Reload Register High Byte ...................... 240 SFR Definition 25.12. TMR2L: Timer 2 Low Byte ....................................................... 240 SFR Definition 25.13. TMR2H Timer 2 High Byte ....................................................... 241 SFR Definition 25.14. TMR3CN: Timer 3 Control ....................................................... 246 SFR Definition 25.15. TMR3RLL: Timer 3 Reload Register Low Byte ........................ 247 SFR Definition 25.16. TMR3RLH: Timer 3 Reload Register High Byte ...................... 247 SFR Definition 25.17. TMR3L: Timer 3 Low Byte ....................................................... 247 SFR Definition 25.18. TMR3H Timer 3 High Byte ....................................................... 248 SFR Definition 25.19. TMR4CN: Timer 4 Control ....................................................... 251 SFR Definition 25.20. TMR4RLL: Timer 4 Reload Register Low Byte ........................ 252 SFR Definition 25.21. TMR4RLH: Timer 4 Reload Register High Byte ...................... 252 SFR Definition 25.22. TMR4L: Timer 4 Low Byte ....................................................... 252 SFR Definition 25.23. TMR4H Timer 4 High Byte ....................................................... 253 SFR Definition 25.24. TMR5CN: Timer 5 Control ....................................................... 256 SFR Definition 25.25. TMR5RLL: Timer 5 Reload Register Low Byte ........................ 257 SFR Definition 25.26. TMR5RLH: Timer 5 Reload Register High Byte ...................... 257 SFR Definition 25.27. TMR5L: Timer 5 Low Byte ....................................................... 257 SFR Definition 25.28. TMR5H Timer 5 High Byte ....................................................... 258 SFR Definition 26.1. PCA0CN: PCA Control .............................................................. 272 SFR Definition 26.2. PCA0MD: PCA Mode ................................................................ 273 SFR Definition 26.3. PCA0CPMn: PCA Capture/Compare Mode .............................. 274 SFR Definition 26.4. PCA0L: PCA Counter/Timer Low Byte ...................................... 275 SFR Definition 26.5. PCA0H: PCA Counter/Timer High Byte ..................................... 275 SFR Definition 26.6. PCA0CPLn: PCA Capture Module Low Byte ............................. 276 SFR Definition 26.7. PCA0CPHn: PCA Capture Module High Byte ........................... 276 C2 Register Definition 27.1. C2ADD: C2 Address ...................................................... 277 C2 Register Definition 27.2. DEVICEID: C2 Device ID ............................................... 278 C2 Register Definition 27.3. REVID: C2 Revision ID .................................................. 278 C2 Register Definition 27.4. FPCTL: C2 Flash Programming Control ........................ 279 C2 Register Definition 27.5. FPDAT: C2 Flash Programming Data ............................ 279 14 Rev. 1.2 C8051F388/9/A/B 1. System Overview C8051F388/9/A/B devices are fully integrated mixed-signal System-on-a-Chip MCUs. Highlighted features are listed below. Refer to Table 1.1 for specific product feature selection.            High-speed pipelined 8051-compatible microcontroller core (up to 48 MIPS) In-system, full-speed, non-intrusive debug interface (on-chip) Supply Voltage Regulator True 10-bit 500 ksps differential / single-ended ADC with analog multiplexer On-chip Voltage Reference and Temperature Sensor On-chip Voltage Comparators (2) Precision internal calibrated 48 MHz internal oscillator Internal low-frequency oscillator for additional power savings Up to 64 kB of on-chip Flash memory Up to 4352 Bytes of on-chip RAM (256 + 4 kB) External Memory Interface (EMIF) available on 48-pin versions.  2 I2C/SMBus, 2 UARTs, and Enhanced SPI serial interfaces implemented in hardware Four general-purpose 16-bit timers Programmable Counter/Timer Array (PCA) with five capture/compare modules and Watchdog Timer function On-chip Power-On Reset, VDD Monitor, and Missing Clock Detector  Up to 40 Port I/O (5 V tolerant)    With on-chip Power-On Reset, VDD monitor, Voltage Regulator, Watchdog Timer, and clock oscillator, C8051F388/9/A/B devices are truly stand-alone System-on-a-Chip solutions. The Flash memory can be reprogrammed in-circuit, providing non-volatile data storage, and also allowing field upgrades of the 8051 firmware. User software has complete control of all peripherals, and may individually shut down any or all peripherals for power savings. The on-chip Silicon Labs 2-Wire (C2) Development Interface allows non-intrusive (uses no on-chip resources), full speed, in-circuit debugging using the production MCU installed in the final application. This debug logic supports inspection and modification of memory and registers, setting breakpoints, single stepping, run and halt commands. All analog and digital peripherals are fully functional while debugging using C2. The two C2 interface pins can be shared with user functions, allowing in-system debugging without occupying package pins. Each device is specified for 2.7–5.25 V operation over the industrial temperature range (–40 to +85 °C). For voltages above 3.6 V, the on-chip Voltage Regulator must be used. The Port I/O and RST pins are tolerant of input signals up to 5 V. C8051F388/9/A/B devices are available in 48-pin TQFP, 32-pin LQFP, or 32-pin QFN packages. See Table 1.1, “Product Selection Guide,” on page 16 for feature and package choices. Rev. 1.2 15 C8051F388/9/A/B 64k 4352    2  2 6  25 —    2 LQFP32 C8051F389-B-GM 48 64k 4352    2  2 6  25 —    2 QFN32 C8051F38A-B-GQ 48 32k 2304    2  2 6  40     2 TQFP48 C8051F38B-B-GQ 48 32k 2304    2  2 6  25 —    2 LQFP32 C8051F38B-B-GM 48 32k 2304    2  2 6  25 —    2 QFN32 Package 48 Analog Comparators C8051F389-B-GQ Voltage Reference TQFP48 Temperature Sensor     2 10-bit 500ksps ADC Programmable Counter Array  40 Digital Port I/O Timers (16-bit) 6 UARTs  2 Enhanced SPI    2 SMBus/I2C 4352 Supply Voltage Regulator 64k Low Frequency Oscillator RAM 48 Calibrated Internal Oscillator Flash Memory (Bytes) C8051F388-B-GQ Ordering Part Number MIPS (Peak) External Memory Interface (EMIF) Table 1.1. Product Selection Guide Note: Starting with silicon revision B, the ordering part numbers have been updated to include the silicon revision and use this format: "C8051F388-B-GQ". 16 Rev. 1.2 C8051F388/9/A/B Figure 1.1. C8051F388/A Block Diagram Rev. 1.2 17 C8051F388/9/A/B Figure 1.2. C8051F389/B Block Diagram 18 Rev. 1.2 C8051F388/9/A/B 2. C8051F34x Compatibility The C8051F388/9/A/B family is designed to be a pin and code compatible replacement for the C8051F34x device family. The C8051F388/9/A/B device should function as a drop-in replacement for the C8051F34x devices in most applications that do not use USB. Table 2.1 lists recommended replacement part numbers for C8051F34x devices. See “2.1. Hardware Incompatibilities” to determine if any changes are necessary when upgrading an existing C8051F34x design to the C8051F388/9/A/B. Table 2.1. C8051F388/9/A/B Replacement Part Numbers C8051F34x Part Number C8051F38x Part Number C8051F340-GQ C8051F388-B-GQ C8051F341-GQ C8051F38A-B-GQ C8051F342-GQ C8051F389-B-GQ C8051F342-GM C8051F389-B-GM C8051F343-GQ C8051F38B-B-GQ C8051F343-GM C8051F38B-B-GM C8051F344-GQ C8051F388-B-GQ C8051F345-GQ C8051F38A-B-GQ C8051F346-GQ C8051F389-B-GQ C8051F346-GM C8051F389-B-GM C8051F347-GQ C8051F38B-B-GQ C8051F347-GM C8051F38B-B-GM C8051F348-GQ C8051F38A-B-GQ C8051F349-GQ C8051F38B-B-GQ C8051F349-GM C8051F38B-B-GM C8051F34A-GQ C8051F389-B-GQ C8051F34A-GM C8051F389-B-GM C8051F34B-GQ C8051F38B-B-GQ C8051F34B-GM C8051F38B-B-GM C8051F34C-GQ C8051F388-B-GQ C8051F34D-GQ C8051F389-B-GQ Rev. 1.2 19 C8051F388/9/A/B 2.1. Hardware Incompatibilities While the C8051F388/9/A/B family includes a number of new features not found on the C8051F34x family, there are some differences that should be considered for any design port.     20 Clock Multiplier: The C8051F388/9/A/B does not include the 4x clock multiplier from the C8051F34x device families. This change only impacts systems which use the clock multiplier in conjunction with an external oscillator source. USB: The C8051F388/9/A/B devices do not include the USB module. External Oscillator C and RC Modes: The C and RC modes of the oscillator have a divide-by-2 stage on the C8051F388/9/A/B to aid in noise immunity. This was not present on the C8051F34x device family, and any clock generated with C or RC mode will change accordingly. Fab Technology: The C8051F388/9/A/B is manufactured using a different technology process than the C8051F34x. As a result, many of the electrical performance parameters will have subtle differences. These differences should not affect most systems but it is nonetheless important to review the electrical parameters for any blocks that are used in the design, and ensure they are compatible with the existing hardware. Rev. 1.2 C8051F388/9/A/B 3. Pinout and Package Definitions Table 3.1. Pin Definitions for the C8051F388/9/A/B Name Pin Numbers Type Description 48-pin 32-pin VDD 10 6 Power In 2.7–3.6 V Power Supply Voltage Input. Power Out GND 7 3 RST/ 13 9 C2CK 3.3 V Voltage Regulator Output. Ground. D I/O Device Reset. Open-drain output of internal POR or VDD monitor. An external source can initiate a system reset by driving this pin low for at least 15 μs. D I/O Clock signal for the C2 Debug Interface. C2D 14 — D I/O Bi-directional data signal for the C2 Debug Interface. P3.0 / — 10 D I/O Port 3.0. See Section 20 for a complete description of Port 3. D I/O Bi-directional data signal for the C2 Debug Interface. C2D REGIN 11 7 Power In 5 V Regulator Input. This pin is the input to the on-chip voltage regulator. INT2 12 8 NC 8 4 This pin is a no-connect and can be left floating. NC 9 5 This pin is a no-connect and can be left floating. P0.0 6 2 D I/O or Port 0.0. See Section 20 for a complete description of Port 0. A In P0.1 5 1 D I/O or Port 0.1. A In P0.2 4 32 D I/O or Port 0.2. A In P0.3 3 31 D I/O or Port 0.3. A In P0.4 2 30 D I/O or Port 0.4. A In P0.5 1 29 D I/O or Port 0.5. A In P0.6 48 28 D I/O or Port 0.6. A In P0.7 47 27 D I/O or Port 0.7. A In D In INT2 interrupt input. Rev. 1.2 21 C8051F388/9/A/B Table 3.1. Pin Definitions for the C8051F388/9/A/B (Continued) Name Pin Numbers Type Description 48-pin 32-pin P1.0 46 26 D I/O or Port 1.0. See Section 20 for a complete description of Port 1. A In P1.1 45 25 D I/O or Port 1.1. A In P1.2 44 24 D I/O or Port 1.2. A In P1.3 43 23 D I/O or Port 1.3. A In P1.4 42 22 D I/O or Port 1.4. A In P1.5 41 21 D I/O or Port 1.5. A In P1.6 40 20 D I/O or Port 1.6. A In P1.7 39 19 D I/O or Port 1.7. A In P2.0 38 18 D I/O or Port 2.0. See Section 20 for a complete description of Port 2. A In P2.1 37 17 D I/O or Port 2.1. A In P2.2 36 16 D I/O or Port 2.2. A In P2.3 35 15 D I/O or Port 2.3. A In P2.4 34 14 D I/O or Port 2.4. A In P2.5 33 13 D I/O or Port 2.5. A In P2.6 32 12 D I/O or Port 2.6. A In P2.7 31 11 D I/O or Port 2.7. A In P3.0 30 — D I/O or Port 3.0. See Section 20 for a complete description of Port 3. A In P3.1 29 — D I/O or Port 3.1. A In 22 Rev. 1.2 C8051F388/9/A/B Table 3.1. Pin Definitions for the C8051F388/9/A/B (Continued) Name Pin Numbers Type Description 48-pin 32-pin P3.2 28 — D I/O or Port 3.2. A In P3.3 27 — D I/O or Port 3.3. A In P3.4 26 — D I/O or Port 3.4. A In P3.5 25 — D I/O or Port 3.5. A In P3.6 24 — D I/O or Port 3.6. A In P3.7 23 — D I/O or Port 3.7. A In P4.0 22 — D I/O or Port 4.0. See Section 20 for a complete description of Port 4. A In P4.1 21 — D I/O or Port 4.1. A In P4.2 20 — D I/O or Port 4.2. A In P4.3 19 — D I/O or Port 4.3. A In P4.4 18 — D I/O or Port 4.4. A In P4.5 17 — D I/O or Port 4.5. A In P4.6 16 — D I/O or Port 4.6. A In P4.7 15 — D I/O or Port 4.7. A In Rev. 1.2 23 C8051F388/9/A/B Figure 3.1. TQFP-48 (C8051F388/A) Pinout Diagram (Top View) 24 Rev. 1.2 C8051F388/9/A/B Figure 3.2. TQFP-48 Package Diagram Table 3.2. TQFP-48 Package Dimensions Dimension A A1 A2 b c D D1 e Min — 0.05 0.95 0.17 0.09 Nom — — 1.00 0.22 — 9.00 BSC 7.00 BSC 0.50 BSC Max 1.20 0.15 1.05 0.27 0.20 Dimension E E1 L aaa bbb ccc ddd q Min 0.45 0° Nom 9.00 BSC 7.00 BSC 0.60 0.20 0.20 0.08 0.08 3.5° Max 0.75 7° Notes: 1. All dimensions shown are in millimeters (mm) unless otherwise noted. 2. Dimensioning and Tolerancing per ANSI Y14.5M-1994. 3. This drawing conforms to JEDEC outline MS-026, variation ABC. 4. The recommended card reflow profile is per the JEDEC/IPC J-STD-020 specification for Small Body Components. Rev. 1.2 25 C8051F388/9/A/B Figure 3.3. TQFP-48 Recommended PCB Land Pattern Table 3.3. TQFP-48 PCB Land Pattern Dimensions Dimension C1 C2 E X1 Y1 Min 8.30 8.30 Max 8.40 8.40 0.50 BSC 0.20 1.40 0.30 1.50 Notes: General: 1. All dimensions shown are in millimeters (mm) unless otherwise noted. 2. This Land Pattern Design is based on the IPC-7351 guidelines. Solder Mask Design: 3. All metal pads are to be non-solder mask defined (NSMD). Clearance between the solder mask and the metal pad is to be 60 μm minimum, all the way around the pad. Stencil Design: 4. A stainless steel, laser-cut and electro-polished stencil with trapezoidal walls should be used to assure good solder paste release. 5. The stencil thickness should be 0.125 mm (5 mils). 6. The ratio of stencil aperture to land pad size should be 1:1 for all pads. Card Assembly: 7. A No-Clean, Type-3 solder paste is recommended. 8. The recommended card reflow profile is per the JEDEC/IPC J-STD-020 specification for Small Body Components. 26 Rev. 1.2 C8051F388/9/A/B Figure 3.4. LQFP-32 (C8051F389/B) Pinout Diagram (Top View) Rev. 1.2 27 C8051F388/9/A/B Figure 3.5. LQFP-32 Package Diagram Table 3.4. LQFP-32 Package Dimensions Dimension A A1 A2 b c D D1 e Min — 0.05 1.35 0.30 0.09 Nom — — 1.40 0.37 — 9.00 BSC 7.00 BSC 0.80 BSC Max 1.60 0.15 1.45 0.45 0.20 Dimension E E1 L aaa bbb ccc ddd q Min 0.45 0° Nom 9.00 BSC 7.00 BSC 0.60 0.20 0.20 0.10 0.20 3.5° Notes: 1. All dimensions shown are in millimeters (mm) unless otherwise noted. 2. Dimensioning and Tolerancing per ANSI Y14.5M-1994. 3. This drawing conforms to JEDEC outline MS-026, variation BBA. 4. The recommended card reflow profile is per the JEDEC/IPC J-STD-020 specification for Small Body Components. 28 Rev. 1.2 Max 0.75 7° C8051F388/9/A/B Figure 3.6. LQFP-32 Recommended PCB Land Pattern Table 3.5. LQFP-32 PCB Land Pattern Dimensions Dimension C1 C2 E X1 Y1 Min 8.40 8.40 Max 8.50 8.50 0.80 BSC 0.40 1.25 0.50 1.35 Notes: General: 1. All dimensions shown are in millimeters (mm) unless otherwise noted. 2. This Land Pattern Design is based on the IPC-7351 guidelines. Solder Mask Design: 3. All metal pads are to be non-solder mask defined (NSMD). Clearance between the solder mask and the metal pad is to be 60 μm minimum, all the way around the pad. Stencil Design: 4. A stainless steel, laser-cut and electro-polished stencil with trapezoidal walls should be used to assure good solder paste release. 5. The stencil thickness should be 0.125 mm (5 mils). 6. The ratio of stencil aperture to land pad size should be 1:1 for all pads. Card Assembly: 7. A No-Clean, Type-3 solder paste is recommended. 8. The recommended card reflow profile is per the JEDEC/IPC J-STD-020 specification for Small Body Components. Rev. 1.2 29 C8051F388/9/A/B Figure 3.7. QFN-32 (C8051F389/B) Pinout Diagram (Top View) 30 Rev. 1.2 C8051F388/9/A/B Figure 3.8. QFN-32 Package Drawing Table 3.6. QFN-32 Package Dimensions Dimension Min Typ Max Dimension Min Typ Max A A1 b D D2 e E 0.80 0.00 0.18 0.85 0.02 0.25 5.00 BSC 3.30 0.50 BSC 5.00 BSC 0.90 0.05 0.30 E2 L aaa bbb ddd eee 3.20 0.35 — — — — 3.30 0.40 — — — — 3.40 0.45 0.10 0.10 0.05 0.08 3.20 3.40 Notes: 1. All dimensions shown are in millimeters (mm) unless otherwise noted. 2. Dimensioning and Tolerancing per ANSI Y14.5M-1994. 3. This drawing conforms to the JEDEC Solid State Outline MO-220, variation VHHD except for custom features D2, E2, and L which are toleranced per supplier designation. 4. The recommended card reflow profile is per the JEDEC/IPC J-STD-020 specification for Small Body Components. Rev. 1.2 31 C8051F388/9/A/B Figure 3.9. QFN-32 Recommended PCB Land Pattern Table 3.7. QFN-32 PCB Land Pattern Dimensions Dimension Min Max Dimension Min Max C1 C2 E X1 4.80 4.80 4.90 4.90 X2 Y1 Y2 3.20 0.75 3.20 3.40 0.85 3.40 0.50 BSC 0.20 0.30 Notes: General: 1. All dimensions shown are in millimeters (mm) unless otherwise noted. 2. This Land Pattern Design is based on the IPC-7351 guidelines. Solder Mask Design: 3. All metal pads are to be non-solder mask defined (NSMD). Clearance between the solder mask and the metal pad is to be 60 m minimum, all the way around the pad. Stencil Design: 4. A stainless steel, laser-cut and electro-polished stencil with trapezoidal walls should be used to assure good solder paste release. 5. The stencil thickness should be 0.125 mm (5 mils). 6. The ratio of stencil aperture to land pad size should be 1:1 for all perimeter pins. 7. A 3x3 array of 1.0 mm openings on a 1.2mm pitch should be used for the center pad to assure the proper paste volume. Card Assembly: 8. A No-Clean, Type-3 solder paste is recommended. 9. The recommended card reflow profile is per the JEDEC/IPC J-STD-020 specification for Small Body Components. 32 Rev. 1.2 C8051F388/9/A/B 4. Typical Connection Diagrams This section provides typical connection diagrams for C8051F388/9/A/B devices. 4.1. Power Figure 4.1 shows a typical connection diagram for the power pins of the C8051F388/9/A/B devices when the internal regulator is in use. The INT2 pin may be left floating. Figure 4.1. Connection Diagram with Voltage Regulator Used Figure 4.2 shows a typical connection diagram for the power pins of the C8051F388/9/A/B devices when the internal regulator is not used. Figure 4.2. Connection Diagram with Voltage Regulator Not Used Rev. 1.2 33 C8051F388/9/A/B 5. Electrical Characteristics 5.1. Absolute Maximum Specifications Table 5.1. Absolute Maximum Ratings Parameter Min Typ Max Units Junction Temperature Under Bias –55 — 125 °C Storage Temperature –65 — 150 °C VDD > 2.2 V VDD < 2.2 V –0.3 –0.3 — — 5.8 VDD + 3.6 V V Regulator1 in Normal Mode Regulator1 in Bypass Mode –0.3 –0.3 — — 4.2 1.98 V V Maximum Total Current through VDD or GND — — 500 mA Maximum Output Current sunk by RST or any Port Pin — — 100 mA Voltage on RST, INT2, or any Port I/O Pin with Respect to GND Voltage on VDD with Respect to GND Conditions Note: Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the devices at those or any other conditions above those indicated in the operation listings of this specification is not implied. Exposure to maximum rating conditions for extended periods may affect device reliability. 34 Rev. 1.2 C8051F388/9/A/B 5.2. Electrical Characteristics Table 5.2. Global Electrical Characteristics –40 to +85 °C, 25 MHz system clock unless otherwise specified. Parameter Test Condition Digital Supply Voltage Digital Supply RAM Data Retention Voltage SYSCLK (System Clock)1 Specified Operating Temperature Range Min Typ Max Unit VRST — 3.3 1.5 3.6 — V V 0 –40 — — 48 +85 MHz °C 14 8 0.85 — mA mA mA μA Digital Supply Current—CPU Active (Normal Mode, fetching instructions from Flash) IDD2 SYSCLK = 48 MHz, VDD = 3.3 V SYSCLK = 24 MHz, VDD = 3.3 V SYSCLK = 1 MHz, VDD = 3.3 V SYSCLK = 80 kHz, VDD = 3.3 V — — — — 12 7 0.45 280 Digital Supply Current—CPU Inactive (Idle Mode, not fetching instructions from Flash) Idle IDD2 Digital Supply Current (Stop or Suspend Mode, shutdown) SYSCLK = 48 MHz, VDD = 3.3 V SYSCLK = 24 MHz, VDD = 3.3 V SYSCLK = 1 MHz, VDD = 3.3 V SYSCLK = 80 kHz, VDD = 3.3 V Oscillator not running (STOP mode), Internal Regulators OFF, VDD = 3.3 V Oscillator not running (STOP or SUSPEND), REG0 and REG1 both in low power mode, VDD = 3.3 V. Oscillator not running (STOP or SUSPEND), REG0 OFF, VDD = 3.3 V. — — — — — 6.5 3.5 0.35 220 1 8 5 — — — mA mA mA μA μA — 100 — μA — 150 — μA Notes: 1. SYSCLK must be at least 32 kHz to enable debugging. 2. Includes normal mode bias current for REG0 and REG1. Does not include current from internal oscillators or other analog peripherals. Rev. 1.2 35 C8051F388/9/A/B Table 5.3. Port I/O DC Electrical Characteristics VDD = 2.7 to 3.6 V, –40 to +85 °C unless otherwise specified. Parameter Test Condition Min Typ Max Unit Output High Voltage IOH = –3 mA, Port I/O push-pull IOH = –10 μA, Port I/O push-pull IOH = –10 mA, Port I/O push-pull VDD – 0.7 VDD – 0.1 — — — VDD – 0.8 — — — V Output Low Voltage IOL = 8.5 mA IOL = 10 μA IOL = 25 mA — — — — — 1.0 0.6 0.1 — V Input High Voltage 2.0 — — V Input Low Voltage — — 0.8 V — — — 15 ±1 50 μA INT2 Detection Input Low Voltage — — 1.0 INT2 Detection Input High Voltage 3.0 — — Input Leakage Current Weak Pullup Off Weak Pullup On, VIN = 0 V V V Table 5.4. Reset Electrical Characteristics –40 to +85 °C unless otherwise specified. Parameter Test Condition Min Typ Max Unit IOL = 8.5 mA, VDD = 2.7 V to 3.6 V — — 0.6 V RST Input High Voltage 0.7 x VDD — — V RST Input Low Voltage — — 0.3 x VDD V — 15 40 μA 2.60 2.65 2.70 V Time from last system clock rising edge to reset initiation 80 580 800 μs Delay between release of any reset source and code execution at location 0x0000 — — 250 μs Minimum RST Low Time to Generate a System Reset 15 — — μs VDD Monitor Turn-on Time — — 100 μs VDD Monitor Supply Current — 15 50 μA RST Output Low Voltage RST Input Pullup Current RST = 0.0 V VDD Monitor Threshold (VRST) Missing Clock Detector Timeout Reset Time Delay 36 Rev. 1.2 C8051F388/9/A/B Table 5.5. Internal Voltage Regulator Electrical Characteristics –40 to +85 °C unless otherwise specified. Parameter Test Condition Min Typ Max Unit 2.7 — 5.25 V 3.0 3.3 3.6 V — — 100 mA — 1 — mV/mA 1.8 — 3.6 V Voltage Regulator (REG0) Input Voltage Range1 Output Output Voltage (VDD)2 Current2 Output Current = 1 to 100 mA 3 Dropout Voltage (VDO) Voltage Regulator (REG1) Input Voltage Range Notes: 1. Input range specified for regulation. When an external regulator is used, should be tied to VDD. 2. Output current is total regulator output, including any current required by the C8051F388/9/A/B. 3. The minimum input voltage is 2.70 V or VDD + VDO (max load), whichever is greater. Table 5.6. Flash Electrical Characteristics Parameter Flash Size Endurance Erase Cycle Time Write Cycle Time Test Condition Min Typ Max Unit C8051F388/9* C8051F38A/B 65536* 32768 10k 10 10 — — 100k 15 15 — 22.5 20 Bytes Bytes Erase/Write ms μs 25 MHz System Clock 25 MHz System Clock Notes: 1. 1024 bytes at location 0xFC00 to 0xFFFF are not available for program storage. 2. Data Retention Information is published in the Quarterly Quality and Reliability Report. Rev. 1.2 37 C8051F388/9/A/B Table 5.7. Internal High-Frequency Oscillator Electrical Characteristics VDD = 2.7 to 3.6 V; TA = –40 to +85 °C unless otherwise specified; Using factory-calibrated settings. Parameter Test Condition Min Typ Max Unit IFCN = 11b 47.3 48 48.7 MHz Oscillator Supply Current (from VDD) 25 °C, VDD = 3.0 V, OSCICN.7 = 1, OCSICN.5 = 0 — 900 — μA Power Supply Sensitivity Constant Temperature — 110 — ppm/V Temperature Sensitivity Constant Supply — 25 — ppm/°C Oscillator Frequency Table 5.8. Internal Low-Frequency Oscillator Electrical Characteristics VDD = 2.7 to 3.6 V; TA = –40 to +85 °C unless otherwise specified; Using factory-calibrated settings. Parameter Test Condition Min Typ Max Unit OSCLD = 11b 75 80 85 kHz Oscillator Supply Current (from VDD) 25 °C, VDD = 3.0 V, OSCLCN.7 = 1 — 4 — μA Power Supply Sensitivity Constant Temperature — 0.05 — %/V Temperature Sensitivity Constant Supply — 65 — ppm/°C Min Typ Max Unit 0.02 — 30 MHz 0 — 48 MHz Oscillator Frequency Table 5.9. External Oscillator Electrical Characteristics VDD = 2.7 to 3.6 V; TA = –40 to +85 °C unless otherwise specified. Parameter Test Condition External Crystal Frequency External CMOS Oscillator Frequency 38 Rev. 1.2 C8051F388/9/A/B Table 5.10. ADC0 Electrical Characteristics VDD = 3.0 V, VREF = 2.40 V (REFSL=0), PGA Gain = 1, –40 to +85 °C unless otherwise specified. Parameter Test Condition Min Typ Max Unit DC Accuracy Resolution 10 Integral Nonlinearity bits — ±0.5 ±1 LSB — ±0.5 ±1 LSB Offset Error –2 0 2 LSB Full Scale Error –5 –2 0 LSB Offset Temperature Coefficient — 0.005 — LSB/°C Differential Nonlinearity Guaranteed Monotonic Dynamic performance (10 kHz sine-wave single-ended input, 1 dB below Full Scale, 500 ksps) Signal-to-Noise Plus Distortion 55 58 — dB — –73 — dB — 78 — dB — — 8.33 MHz 13 11 — — — — clocks clocks 300 — — ns — — 500 ksps Single Ended (AIN+ – GND) 0 — VREF V Differential (AIN+ – AIN–) –VREF — VREF V Single Ended or Differential 0 — VDD V Sampling Capacitance — 30 — pF Input Multiplexer Impedance — 5 — k — 750 1000 μA — 1 — mV/V Total Harmonic Distortion Up to the 5th harmonic Spurious-Free Dynamic Range Conversion Rate SAR Conversion Clock Conversion Time in SAR Clocks 10-bit Mode 8-bit Mode Track/Hold Acquisition Time Throughput Rate Analog Inputs ADC Input Voltage Range Absolute Pin Voltage with respect to GND Power Specifications Power Supply Current (VDD supplied to ADC0) Operating Mode, 500 ksps Power Supply Rejection Note: Represents one standard deviation from the mean. Rev. 1.2 39 C8051F388/9/A/B Table 5.11. Temperature Sensor Electrical Characteristics VDD = 3.0 V, –40 to +85 °C unless otherwise specified. Parameter Test Condition Min Typ Max Unit Linearity — ± 0.5 — °C Slope — 2.87 — mV/°C Slope Error* — ±120 — μV/°C Offset Temp = 0 °C — 764 — mV Offset Error* Temp = 0 °C — ±15 — mV Note: Represents one standard deviation from the mean. Table 5.12. Voltage Reference Electrical Characteristics VDD = 3.0 V; –40 to +85 °C unless otherwise specified. Parameter Test Condition Min Typ Max Unit 25 °C ambient 2.38 2.42 2.46 V VREF Short-Circuit Current — — 8 mA VREF Temperature Coefficient — 35 — ppm/°C Load = 0 to 200 μA to GND — 1.5 — ppm/μA VREF Turn-on Time 1 4.7 μF tantalum, 0.1 μF ceramic bypass — 3 — ms VREF Turn-on Time 2 0.1 μF ceramic bypass — 100 — μs — 140 — ppm/V 1 — VDD V — 9 — μA — 75 — μA Internal Reference (REFBE = 1) Output Voltage Load Regulation Power Supply Rejection External Reference (REFBE = 0) Input Voltage Range Input Current Sample Rate = 500 ksps; VREF = 3.0 V Power Specifications Supply Current 40 Rev. 1.2 C8051F388/9/A/B Table 5.13. Comparator Electrical Characteristics VDD = 3.0 V, –40 to +85 °C unless otherwise noted. Parameter Response Time: Mode 0, Vcm* = 1.5 V Response Time: Mode 1, Vcm* = 1.5 V Response Time: Mode 2, Vcm* = 1.5 V Response Time: Mode 3, Vcm* = 1.5 V Test Condition Min Typ Max Unit CP0+ – CP0– = 100 mV — 100 — ns CP0+ – CP0– = –100 mV — 250 — ns CP0+ – CP0– = 100 mV — 175 — ns CP0+ – CP0– = –100 mV — 500 — ns CP0+ – CP0– = 100 mV — 320 — ns CP0+ – CP0– = –100 mV — 1100 — ns CP0+ – CP0– = 100 mV — 1050 — ns CP0+ – CP0– = –100 mV — 5200 — ns — 1.5 4 mV/V Common-Mode Rejection Ratio Positive Hysteresis 1 CP0HYP1–0 = 00 — 0 1 mV Positive Hysteresis 2 CP0HYP1–0 = 01 2 5 10 mV Positive Hysteresis 3 CP0HYP1–0 = 10 7 10 20 mV Positive Hysteresis 4 CP0HYP1–0 = 11 15 20 30 mV Negative Hysteresis 1 CP0HYN1–0 = 00 — 0 1 mV Negative Hysteresis 2 CP0HYN1–0 = 01 2 5 10 mV Negative Hysteresis 3 CP0HYN1–0 = 10 7 10 20 mV Negative Hysteresis 4 CP0HYN1–0 = 11 15 20 30 mV –0.25 — VDD + 0.25 V Input Capacitance — 4 — pF Input Bias Current — 0.001 — nA –10 — +10 mV Power Supply Rejection — 0.1 — mV/V Power-up Time — 10 — μs Mode 0 — 20 — μA Mode 1 — 10 — μA Mode 2 — 4 — μA Mode 3 — 1 — μA Inverting or Non-Inverting Input Voltage Range Input Offset Voltage Power Supply Supply Current at DC Note: Vcm is the common-mode voltage on CP0+ and CP0–. Rev. 1.2 41 C8051F388/9/A/B 6. 10-Bit ADC ADC0 on the C8051F388/9/A/B is a 500 ksps, 10-bit successive-approximation-register (SAR) ADC with integrated track-and-hold, and a programmable window detector. The ADC is fully configurable under software control via Special Function Registers. The ADC may be configured to measure various different signals using the analog multiplexer described in Section “6.5. ADC0 Analog Multiplexer” on page 55. The voltage reference for the ADC is selected as described in Section “7. Voltage Reference Options” on page 58. The ADC0 subsystem is enabled only when the AD0EN bit in the ADC0 Control register (ADC0CN) is set to logic 1. The ADC0 subsystem is in low power shutdown when this bit is logic 0. Figure 6.1. ADC0 Functional Block Diagram 42 Rev. 1.2 C8051F388/9/A/B 6.1. Output Code Formatting The conversion code format differs between Single-ended and Differential modes. The registers ADC0H and ADC0L contain the high and low bytes of the output conversion code from the ADC at the completion of each conversion. Data can be right-justified or left-justified, depending on the setting of the AD0LJST bit (ADC0CN.0). When in Single-ended Mode, conversion codes are represented as 10-bit unsigned integers. Inputs are measured from 0 to VREF x 1023/1024. Example codes are shown below for both right-justified and left-justified data. Unused bits in the ADC0H and ADC0L registers are set to 0. Input Voltage (Single-Ended) VREF x 1023/1024 VREF x 512/1024 VREF x 256/1024 0 Right-Justified ADC0H:ADC0L (AD0LJST = 0) Left-Justified ADC0H:ADC0L (AD0LJST = 1) 0x03FF 0x0200 0x0100 0x0000 0xFFC0 0x8000 0x4000 0x0000 When in Differential Mode, conversion codes are represented as 10-bit signed 2s complement numbers. Inputs are measured from –VREF to VREF x 511/512. Example codes are shown below for both right-justified and left-justified data. For right-justified data, the unused MSBs of ADC0H are a sign-extension of the data word. For left-justified data, the unused LSBs in the ADC0L register are set to 0. Input Voltage (Differential) VREF x 511/512 VREF x 256/512 0 –VREF x 256/512 –VREF Right-Justified ADC0H:ADC0L (AD0LJST = 0) Left-Justified ADC0H:ADC0L (AD0LJST = 1) 0x01FF 0x0100 0x0000 0xFF00 0xFE00 0x7FC0 0x4000 0x0000 0xC000 0x8000 Rev. 1.2 43 C8051F388/9/A/B 6.2. Temperature Sensor The typical temperature sensor transfer function is shown in Figure 6.2. The output voltage (VTEMP) is the positive ADC input when the temperature sensor is selected by bits AMX0P5-0 in register AMX0P. Figure 6.2. Typical Temperature Sensor Transfer Function The uncalibrated temperature sensor output is extremely linear and suitable for relative temperature measurements (see Table 5.10, “ADC0 Electrical Characteristics,” on page 39 for linearity specifications). For absolute temperature measurements, gain and/or offset calibration is recommended. Typically a 1-point calibration includes the following steps: Step 1. Control/measure the ambient temperature (this temperature must be known). Step 2. Power the device, and delay for a few seconds to allow for self-heating. Step 3. Perform an ADC conversion with the temperature sensor selected as the positive input and GND selected as the negative input. Step 4. Calculate the offset and/or gain characteristics, and store these values in non-volatile memory for use with subsequent temperature sensor measurements. Figure 6.3 shows the typical temperature sensor error assuming a 1-point calibration at 25 °C. Note that parameters which affect ADC measurement, in particular the voltage reference value, will also affect temperature measurement. 44 Rev. 1.2 C8051F388/9/A/B Figure 6.3. Temperature Sensor Error with 1-Point Calibration Rev. 1.2 45 C8051F388/9/A/B 6.3. Modes of Operation ADC0 has a maximum conversion speed of 500 ksps. The ADC0 conversion clock is a divided version of the system clock, determined by the AD0SC bits in the ADC0CF register. 6.3.1. Starting a Conversion A conversion can be initiated in one of several ways, depending on the programmed states of the ADC0 Start of Conversion Mode bits (AD0CM2–0) in register ADC0CN. Conversions may be initiated by one of the following: 1. Writing a 1 to the AD0BUSY bit of register ADC0CN 2. A Timer 0 overflow (i.e., timed continuous conversions) 3. A Timer 2 overflow 4. A Timer 1 overflow 5. A rising edge on the CNVSTR input signal 6. A Timer 3 overflow 7. A Timer 4 overflow 8. A Timer 5 overflow Writing a 1 to AD0BUSY provides software control of ADC0 whereby conversions are performed "ondemand". During conversion, the AD0BUSY bit is set to logic 1 and reset to logic 0 when the conversion is complete. The falling edge of AD0BUSY triggers an interrupt (when enabled) and sets the ADC0 interrupt flag (AD0INT). Note: When polling for ADC conversion completions, the ADC0 interrupt flag (AD0INT) should be used. Converted data is available in the ADC0 data registers, ADC0H:ADC0L, when bit AD0INT is logic 1. Note that when Timer 2, 3, 4, or 5 overflows are used as the conversion source, Low Byte overflows are used if the timer is in 8-bit mode; High byte overflows are used if the timer is in 16-bit mode. See Section “25. Timers” on page 224 for timer configuration. Important Note About Using CNVSTR: The CNVSTR input pin also functions as a Port I/O pin. When the CNVSTR input is used as the ADC0 conversion source, the associated pin should be skipped by the Digital Crossbar. See Section “20. Port Input/Output” on page 147 for details on Port I/O configuration. 46 Rev. 1.2 C8051F388/9/A/B 6.3.2. Tracking Modes The AD0TM bit in register ADC0CN controls the ADC0 track-and-hold mode. In its default state, the ADC0 input is continuously tracked, except when a conversion is in progress. When the AD0TM bit is logic 1, ADC0 operates in low-power track-and-hold mode. In this mode, each conversion is preceded by a tracking period of 3 SAR clocks (after the start-of-conversion signal). When the CNVSTR signal is used to initiate conversions in low-power tracking mode, ADC0 tracks only when CNVSTR is low; conversion begins on the rising edge of CNVSTR. See Figure 6.4 for track and convert timing details. Tracking can also be disabled (shutdown) when the device is in low power standby or sleep modes. Low-power track-and-hold mode is also useful when AMUX settings are frequently changed, due to the settling time requirements described in Section “6.3.3. Settling Time Requirements” on page 48. Figure 6.4. 10-Bit ADC Track and Conversion Example Timing Rev. 1.2 47 C8051F388/9/A/B 6.3.3. Settling Time Requirements A minimum tracking time is required before each conversion to ensure that an accurate conversion is performed. This tracking time is determined by the AMUX0 resistance, the ADC0 sampling capacitance, any external source resistance, and the accuracy required for the conversion. Note that in low-power tracking mode, three SAR clocks are used for tracking at the start of every conversion. For most applications, these three SAR clocks will meet the minimum tracking time requirements. Figure 6.5 shows the equivalent ADC0 input circuit. The required ADC0 settling time for a given settling accuracy (SA) may be approximated by Equation 6.1. See Table 5.10 for ADC0 minimum settling time requirements as well as the mux impedance and sampling capacitor values.  2n  t = ln  -------  R TOTAL C SAMPLE  SA Equation 6.1. ADC0 Settling Time Requirements Where: SA is the settling accuracy, given as a fraction of an LSB (for example, 0.25 to settle within 1/4 LSB) t is the required settling time in seconds RTOTAL is the sum of the AMUX0 resistance and any external source resistance. n is the ADC resolution in bits (10). Figure 6.5. ADC0 Equivalent Input Circuits 48 Rev. 1.2 C8051F388/9/A/B SFR Definition 6.1. ADC0CF: ADC0 Configuration Bit 7 6 5 4 3 2 1 0 Name AD0SC[4:0] AD0LJST Reserved Type R/W R/W R/W Reset 1 1 1 1 1 0 0 0 SFR Address = 0xBC; SFR Page = All Pages Bit Name Function 7:3 AD0SC[4:0] ADC0 SAR Conversion Clock Period Bits. SAR Conversion clock is derived from system clock by the following equation, where AD0SC refers to the 5-bit value held in bits AD0SC4–0. SAR Conversion clock requirements are given in the ADC specification table. SYSCLK AD0SC = ------------------------ – 1 CLK SAR Note: If the Memory Power Controller is enabled (MPCE = '1'), AD0SC must be set to at least "00001" for proper ADC operation. 2 AD0LJST ADC0 Left Justify Select. 0: Data in ADC0H:ADC0L registers are right-justified. 1: Data in ADC0H:ADC0L registers are left-justified. Note: The AD0LJST bit is only valid for 10-bit mode (AD08BE = 0). 1:0 Reserved Must Write 00b. Rev. 1.2 49 C8051F388/9/A/B SFR Definition 6.2. ADC0H: ADC0 Data Word MSB Bit 7 6 5 4 3 Name ADC0H[7:0] Type R/W Reset 0 0 0 0 0 SFR Address = 0xBE; SFR Page = All Pages Bit Name 2 1 0 0 0 0 Function 7:0 ADC0H[7:0] ADC0 Data Word High-Order Bits. For AD0LJST = 0: Bits 7–2 will read 000000b. Bits 1–0 are the upper 2 bits of the 10bit ADC0 Data Word. For AD0LJST = 1: Bits 7–0 are the most-significant bits of the 10-bit ADC0 Data Word. SFR Definition 6.3. ADC0L: ADC0 Data Word LSB Bit 7 6 5 4 3 Name ADC0L[7:0] Type R/W Reset 0 0 0 0 SFR Address = 0xBD; SFR Page = All Pages Bit Name 0 2 1 0 0 0 0 Function 7:0 ADC0L[7:0] ADC0 Data Word Low-Order Bits. For AD0LJST = 0: Bits 7–0 are the lower 8 bits of the 10-bit Data Word. For AD0LJST = 1: Bits 7–6 are the lower 2 bits of the 10-bit Data Word. Bits 5–0 will read 000000b. 50 Rev. 1.2 C8051F388/9/A/B SFR Definition 6.4. ADC0CN: ADC0 Control Bit 7 6 5 4 3 Name AD0EN AD0TM AD0INT Type R/W R/W R/W R/W R/W Reset 0 0 0 0 0 2 AD0BUSY AD0WINT 1 0 AD0CM[2:0] R/W 0 0 0 SFR Address = 0xE8; SFR Page = All Pages; Bit-Addressable Bit Name Function 7 AD0EN ADC0 Enable Bit. 0: ADC0 Disabled. ADC0 is in low-power shutdown. 1: ADC0 Enabled. ADC0 is active and ready for data conversions. 6 AD0TM ADC0 Track Mode Bit. 0: Normal Track Mode: When ADC0 is enabled, tracking is continuous unless a conversion is in progress. Conversion begins immediately on start-of-conversion event, as defined by AD0CM[2:0]. 1: Delayed Track Mode: When ADC0 is enabled, input is tracked when a conversion is not in progress. A start-of-conversion signal initiates three SAR clocks of additional tracking, and then begins the conversion. Note that there is not a tracking delay when CNVSTR is used (AD0CM[2:0] = 100). 5 AD0INT ADC0 Conversion Complete Interrupt Flag. 0: ADC0 has not completed a data conversion since AD0INT was last cleared. 1: ADC0 has completed a data conversion. 4 AD0BUSY 3 AD0WINT ADC0 Busy Bit. Read: 0: ADC0 conversion is not in progress. 1: ADC0 conversion is in progress. Write: 0: No Effect. 1: Initiates ADC0 Conversion if AD0CM[2:0] = 000b ADC0 Window Compare Interrupt Flag. 0: ADC0 Window Comparison Data match has not occurred since this flag was last cleared. 1: ADC0 Window Comparison Data match has occurred. 2:0 AD0CM[2:0] ADC0 Start of Conversion Mode Select. 000: ADC0 start-of-conversion source is write of 1 to AD0BUSY. 001: ADC0 start-of-conversion source is overflow of Timer 0. 010: ADC0 start-of-conversion source is overflow of Timer 2. 011: ADC0 start-of-conversion source is overflow of Timer 1. 100: ADC0 start-of-conversion source is rising edge of external CNVSTR. 101: ADC0 start-of-conversion source is overflow of Timer 3. 110: ADC0 start-of-conversion source is overflow of Timer 4. 111: ADC0 start-of-conversion source is overflow of Timer 5. Rev. 1.2 51 C8051F388/9/A/B 6.4. Programmable Window Detector The ADC Programmable Window Detector continuously compares the ADC0 output registers to user-programmed limits, and notifies the system when a desired condition is detected. This is especially effective in an interrupt-driven system, saving code space and CPU bandwidth while delivering faster system response times. The window detector interrupt flag (AD0WINT in register ADC0CN) can also be used in polled mode. The ADC0 Greater-Than (ADC0GTH, ADC0GTL) and Less-Than (ADC0LTH, ADC0LTL) registers hold the comparison values. The window detector flag can be programmed to indicate when measured data is inside or outside of the user-programmed limits, depending on the contents of the ADC0 Less-Than and ADC0 Greater-Than registers. SFR Definition 6.5. ADC0GTH: ADC0 Greater-Than Data High Byte Bit 7 6 5 4 3 Name ADC0GTH[7:0] Type R/W Reset 1 1 1 1 1 SFR Address = 0xC4; SFR Page = All Pages Bit Name 2 1 0 1 1 1 2 1 0 1 1 1 Function 7:0 ADC0GTH[7:0] ADC0 Greater-Than Data Word High-Order Bits. SFR Definition 6.6. ADC0GTL: ADC0 Greater-Than Data Low Byte Bit 7 6 5 4 3 Name ADC0GTL[7:0] Type R/W Reset 1 1 1 1 SFR Address = 0xC3; SFR Page = All Pages Bit Name 7:0 52 1 Function ADC0GTL[7:0] ADC0 Greater-Than Data Word Low-Order Bits. Rev. 1.2 C8051F388/9/A/B SFR Definition 6.7. ADC0LTH: ADC0 Less-Than Data High Byte Bit 7 6 5 4 3 Name ADC0LTH[7:0] Type R/W Reset 0 0 0 0 0 SFR Address = 0xC6; SFR Page = All Pages Bit Name 7:0 2 1 0 0 0 0 2 1 0 0 0 0 Function ADC0LTH[7:0] ADC0 Less-Than Data Word High-Order Bits. SFR Definition 6.8. ADC0LTL: ADC0 Less-Than Data Low Byte Bit 7 6 5 4 3 Name ADC0LTL[7:0] Type R/W Reset 0 0 0 0 SFR Address = 0xC5; SFR Page = All Pages Bit Name 7:0 0 Function ADC0LTL[7:0] ADC0 Less-Than Data Word Low-Order Bits. Rev. 1.2 53 C8051F388/9/A/B 6.4.1. Window Detector Example Figure 6.6 shows two example window comparisons for right-justified, single-ended data, with ADC0LTH:ADC0LTL = 0x0080 (128d) and ADC0GTH:ADC0GTL = 0x0040 (64d). The input voltage can range from 0 to VREF x (1023/1024) with respect to GND, and is represented by a 10-bit unsigned integer value. In the left example, an AD0WINT interrupt will be generated if the ADC0 conversion word (ADC0H:ADC0L) is within the range defined by ADC0GTH:ADC0GTL and ADC0LTH:ADC0LTL (if 0x0040 < ADC0H:ADC0L < 0x0080). In the right example, and AD0WINT interrupt will be generated if the ADC0 conversion word is outside of the range defined by the ADC0GT and ADC0LT registers (if ADC0H:ADC0L < 0x0040 or ADC0H:ADC0L > 0x0080). Figure 6.7 shows an example using left-justified data with the same comparison values. Figure 6.6. ADC Window Compare Example: Right-Justified Data Figure 6.7. ADC Window Compare Example: Left-Justified Data 54 Rev. 1.2 C8051F388/9/A/B 6.5. ADC0 Analog Multiplexer AMUX0 selects the positive and negative inputs to the ADC. The positive input (AIN+) can be connected to individual Port pins, the on-chip temperature sensor, or the positive power supply (VDD). The negative input (AIN-) can be connected to individual Port pins, VREF, or GND. When GND is selected as the negative input, ADC0 operates in Single-ended Mode; at all other times, ADC0 operates in Differential Mode. The ADC0 input channels are selected in the AMX0P and AMX0N registers as described in SFR Definition 6.9 and SFR Definition 6.10. Important Note About ADC0 Input Configuration: Port pins selected as ADC0 inputs should be configured as analog inputs, and should be skipped by the Digital Crossbar. To configure a Port pin for analog input, set to 0 the corresponding bit in register PnMDIN. To force the Crossbar to skip a Port pin, set to 1 the corresponding bit in register PnSKIP. See Section “20. Port Input/Output” on page 147 for more Port I/O configuration details. Rev. 1.2 55 C8051F388/9/A/B SFR Definition 6.9. AMX0P: AMUX0 Positive Channel Select Bit 7 6 5 4 Name 2 1 0 0 0 AMX0P[5:0] Type R R Reset 0 0 R/W 0 0 SFR Address = 0xBB; SFR Page = All Pages Bit Name 7:6 3 Unused 0 0 Function Read = 00b; Write = don’t care. 5:0 AMX0P[5:0] AMUX0 Positive Input Selection. AMX0P 56 32-pin Packages 48-pin Packages AMX0P 000000: P1.0 P2.0 010010: P0.1 P0.4 000001: P1.1 P2.1 010011: P0.4 P1.1 000010: P1.2 P2.2 010100: P0.5 P1.2 000011: P1.3 P2.3 010101: Reserved P1.0 000100: P1.4 P2.5 010110: Reserved P1.3 000101: P1.5 P2.6 010111: Reserved P1.6 000110: P1.6 P3.0 011000: Reserved P1.7 000111: P1.7 P3.1 011001: Reserved P2.4 001000: P2.0 P3.4 011010: Reserved P2.7 001001: P2.1 P3.5 011011: Reserved P3.2 001010: P2.2 P3.7 011100: Reserved P3.3 001011: P2.3 P4.0 011101: Reserved P3.6 001100: P2.4 P4.3 011110: Temp Sensor Temp Sensor 001101: P2.5 P4.4 011111: VDD VDD 001110: P2.6 P4.5 100000: Reserved P4.1 001111: P2.7 P4.6 100001: Reserved P4.2 010000: P3.0 Reserved 100010: Reserved P4.7 010001: P0.0 P0.3 100011 - Reserved 111111: Reserved Rev. 1.2 32-pin Packages 48-pin Packages C8051F388/9/A/B SFR Definition 6.10. AMX0N: AMUX0 Negative Channel Select Bit 7 6 5 4 Name 2 1 0 0 0 AMX0N[5:0] Type R R Reset 0 0 R/W 0 0 SFR Address = 0xBA; SFR Page = All Pages Bit Name 7:6 3 Unused 0 0 Function Read = 00b; Write = don’t care. 5:0 AMX0N[5:0] AMUX0 Negative Input Selection. AMX0N 32-pin Packages 48-pin Packages AMX0N 000000: P1.0 P2.0 010010: P0.1 P0.4 000001: P1.1 P2.1 010011: P0.4 P1.1 000010: P1.2 P2.2 010100: P0.5 P1.2 000011: P1.3 P2.3 010101: Reserved P1.0 000100: P1.4 P2.5 010110: Reserved P1.3 000101: P1.5 P2.6 010111: Reserved P1.6 000110: P1.6 P3.0 011000: Reserved P1.7 000111: P1.7 P3.1 011001: Reserved P2.4 001000: P2.0 P3.4 011010: Reserved P2.7 001001: P2.1 P3.5 011011: Reserved P3.2 001010: P2.2 P3.7 011100: Reserved P3.3 001011: P2.3 P4.0 011101: Reserved P3.6 001100: P2.4 P4.3 011110: VREF VREF 001101: P2.5 P4.4 011111: GND GND (Single-Ended (Single-Ended Measurement) Measurement) 001110: P2.6 P4.5 100000: Reserved P4.1 001111: P2.7 P4.6 100001: Reserved P4.2 010000: P3.0 Reserved 100010: Reserved P4.7 010001: P0.0 P0.3 100011 - Reserved 111111: Reserved Rev. 1.2 32-pin Packages 48-pin Packages 57 C8051F388/9/A/B 7. Voltage Reference Options The Voltage reference multiplexer for the ADC is configurable to use an externally connected voltage reference, the on-chip reference voltage generator routed to the VREF pin, the unregulated power supply voltage (VDD), or the regulated 1.8 V internal supply (see Figure 7.1). The REFSL bit in the Reference Control register (REF0CN, SFR Definition 7.1) selects the reference source for the ADC. For an external source or the on-chip reference, REFSL should be set to 0 to select the VREF pin. To use VDD as the reference source, REFSL should be set to 1. To override this selection and use the internal regulator as the reference source, the REGOVR bit can be set to 1. The BIASE bit enables the internal voltage bias generator, which is used by many of the analog peripherals on the device. This bias is automatically enabled when any peripheral which requires it is enabled, and it does not need to be enabled manually. The bias generator may be enabled manually by writing a 1 to the BIASE bit in register REF0CN. The electrical specifications for the voltage reference circuit are given in Table 5.12. The C8051F388/9/A/B devices also include an on-chip voltage reference circuit which consists of a 1.2 V, temperature stable bandgap voltage reference generator and a selectable-gain output buffer amplifier. The buffer is configured for 1x or 2x gain using the REFBGS bit in register REF0CN. On the 1x gain setting the output voltage is nominally 1.2 V, and on the 2x gain setting the output voltage is nominally 2.4 V. The onchip voltage reference can be driven on the VREF pin by setting the REFBE bit in register REF0CN to a 1. The maximum load seen by the VREF pin must be less than 200 μA to GND. Bypass capacitors of 0.1 μF and 4.7 μF are recommended from the VREF pin to GND, and a minimum of 0.1uF is required. If the onchip reference is not used, the REFBE bit should be cleared to 0. Electrical specifications for the on-chip voltage reference are given in Table 5.12. Important Note about the VREF Pin: When using either an external voltage reference or the on-chip reference circuitry, the VREF pin should be configured as an analog pin and skipped by the Digital Crossbar. Refer to Section “20. Port Input/Output” on page 147 for the location of the VREF pin, as well as details of how to configure the pin in analog mode and to be skipped by the crossbar. Figure 7.1. Voltage Reference Functional Block Diagram 58 Rev. 1.2 C8051F388/9/A/B SFR Definition 7.1. REF0CN: Reference Control Bit 7 6 Name REFBGS Type R/W R Reset 0 0 5 4 3 2 1 0 REGOVR REFSL TEMPE BIASE REFBE R R/W R/W R/W R/W R/W 0 0 0 0 0 0 SFR Address = 0xD1; SFR Page = All Pages Bit Name 7 6:5 4 Function REFBGS Reference Buffer Gain Select. This bit selects between 1x and 2x gain for the on-chip voltage reference buffer. 0: 2x Gain 1: 1x Gain Unused Read = 00b; Write = don’t care. REGOVR Regulator Reference Override. This bit “overrides” the REFSL bit, and allows the internal regulator to be used as a reference source. 0: The voltage reference source is selected by the REFSL bit. 1: The internal regulator is used as the voltage reference. 3 REFSL Voltage Reference Select. This bit selects the ADCs voltage reference. 0: VREF pin used as voltage reference. 1: VDD used as voltage reference. 2 TEMPE Temperature Sensor Enable Bit. 0: Internal Temperature Sensor off. 1: Internal Temperature Sensor on. 1 BIASE Internal Analog Bias Generator Enable Bit. 0: Internal Bias Generator off. 1: Internal Bias Generator on. 0 REFBE On-chip Reference Buffer Enable Bit. 0: On-chip Reference Buffer off. 1: On-chip Reference Buffer on. Internal voltage reference driven on the VREF pin. Rev. 1.2 59 C8051F388/9/A/B 8. Comparator0 and Comparator1 C8051F388/9/A/B devices include two on-chip programmable voltage comparators: Comparator0 is shown in Figure 8.1, Comparator1 is shown in Figure 8.2. The two comparators operate identically with the following exceptions: (1) Their input selections differ as described in Section “8.1. Comparator Multiplexers” on page 67; (2) Comparator0 can be used as a reset source. The Comparators offer programmable response time and hysteresis, an analog input multiplexer, and two outputs that are optionally available at the Port pins: a synchronous “latched” output (CP0 or CP1), or an asynchronous “raw” output (CP0A or CP1A). The asynchronous signals are available even when the system clock is not active. This allows the Comparators to operate and generate an output with the device in STOP mode. When assigned to a Port pin, the Comparator outputs may be configured as open drain or push-pull (see Section “20.2. Port I/O Initialization” on page 152). Comparator0 may also be used as a reset source (see Section “17.5. Comparator0 Reset” on page 126). The Comparator inputs are selected by the comparator input multiplexers, as detailed in Section “8.1. Comparator Multiplexers” on page 67. Figure 8.1. Comparator0 Functional Block Diagram 60 Rev. 1.2 C8051F388/9/A/B Figure 8.2. Comparator1 Functional Block Diagram The Comparator output can be polled in software, used as an interrupt source, and/or routed to a Port pin. When routed to a Port pin, the Comparator output is available asynchronous or synchronous to the system clock; the asynchronous output is available even in STOP mode (with no system clock active). When disabled, the Comparator output (if assigned to a Port I/O pin via the Crossbar) defaults to the logic low state, and the power supply to the comparator is turned off. See Section “20.1. Priority Crossbar Decoder” on page 148 for details on configuring Comparator outputs via the digital Crossbar. Comparator inputs can be externally driven from –0.25 V to (VDD) + 0.25 V without damage or upset. The complete Comparator electrical specifications are given in Section “5. Electrical Characteristics” on page 34. The Comparator response time may be configured in software via the CPTnMD registers (see SFR Definition 8.2 and SFR Definition 8.4). Selecting a longer response time reduces the Comparator supply current. Rev. 1.2 61 C8051F388/9/A/B Figure 8.3. Comparator Hysteresis Plot The Comparator hysteresis is software-programmable via its Comparator Control register CPTnCN (for n = 0 or 1). The user can program both the amount of hysteresis voltage (referred to the input voltage) and the positive and negative-going symmetry of this hysteresis around the threshold voltage. The Comparator hysteresis is programmed using Bits 3–0 in the Comparator Control Register CPTnCN (shown in SFR Definition 8.1). The amount of negative hysteresis voltage is determined by the settings of the CPnHYN bits. Settings of 20, 10 or 5 mV of nominal negative hysteresis can be programmed, or negative hysteresis can be disabled. In a similar way, the amount of positive hysteresis is determined by the setting the CPnHYP bits. Comparator interrupts can be generated on both rising-edge and falling-edge output transitions. (For Interrupt enable and priority control, see Section “16.1. MCU Interrupt Sources and Vectors” on page 113). The CPnFIF flag is set to logic 1 upon a Comparator falling-edge occurrence, and the CPnRIF flag is set to logic 1 upon the Comparator rising-edge occurrence. Once set, these bits remain set until cleared by software. The Comparator rising-edge interrupt mask is enabled by setting CPnRIE to a logic 1. The Comparator falling-edge interrupt mask is enabled by setting CPnFIE to a logic 1. The output state of the Comparator can be obtained at any time by reading the CPnOUT bit. The Comparator is enabled by setting the CPnEN bit to logic 1, and is disabled by clearing this bit to logic 0. Note that false rising edges and falling edges can be detected when the comparator is first powered on or if changes are made to the hysteresis or response time control bits. Therefore, it is recommended that the rising-edge and falling-edge flags be explicitly cleared to logic 0 a short time after the comparator is enabled or its mode bits have been changed. 62 Rev. 1.2 C8051F388/9/A/B SFR Definition 8.1. CPT0CN: Comparator0 Control Bit 7 6 5 4 Name CP0EN CP0OUT CP0RIF CP0FIF CP0HYP[1:0] CP0HYN[1:0] Type R/W R R/W R/W R/W R/W Reset 0 0 0 0 SFR Address = 0x9B; SFR Page = All Pages Bit Name 3 2 0 0 1 0 0 0 Function 7 CP0EN Comparator0 Enable Bit. 0: Comparator0 Disabled. 1: Comparator0 Enabled. 6 CP0OUT Comparator0 Output State Flag. 0: Voltage on CP0+ < CP0–. 1: Voltage on CP0+ > CP0–. 5 CP0RIF Comparator0 Rising-Edge Flag. Must be cleared by software. 0: No Comparator0 Rising Edge has occurred since this flag was last cleared. 1: Comparator0 Rising Edge has occurred. 4 CP0FIF Comparator0 Falling-Edge Flag. Must be cleared by software. 0: No Comparator0 Falling-Edge has occurred since this flag was last cleared. 1: Comparator0 Falling-Edge has occurred. 3:2 CP0HYP[1:0] Comparator0 Positive Hysteresis Control Bits. 00: Positive Hysteresis Disabled. 01: Positive Hysteresis = 5 mV. 10: Positive Hysteresis = 10 mV. 11: Positive Hysteresis = 20 mV. 1:0 CP0HYN[1:0] Comparator0 Negative Hysteresis Control Bits. 00: Negative Hysteresis Disabled. 01: Negative Hysteresis = 5 mV. 10: Negative Hysteresis = 10 mV. 11: Negative Hysteresis = 20 mV. Rev. 1.2 63 C8051F388/9/A/B SFR Definition 8.2. CPT0MD: Comparator0 Mode Selection Bit 7 6 Name 5 4 CP0RIE CP0FIE 3 2 R R R/W R/W R R Reset 0 0 0 0 0 0 Unused Read = 00b, Write = don’t care. 5 CP0RIE Comparator0 Rising-Edge Interrupt Enable. 0: Comparator0 Rising-edge interrupt disabled. 1: Comparator0 Rising-edge interrupt enabled. 4 CP0FIE Comparator0 Falling-Edge Interrupt Enable. 0: Comparator0 Falling-edge interrupt disabled. 1: Comparator0 Falling-edge interrupt enabled. 3:2 Unused Read = 00b, Write = don’t care. 64 R/W 1 Function 7:6 1:0 0 CP0MD[1:0] Type SFR Address = 0x9D; SFR Page = All Pages Bit Name 1 CP0MD[1:0] Comparator0 Mode Select. These bits affect the response time and power consumption for Comparator0. 00: Mode 0 (Fastest Response Time, Highest Power Consumption) 01: Mode 1 10: Mode 2 11: Mode 3 (Slowest Response Time, Lowest Power Consumption) Rev. 1.2 0 C8051F388/9/A/B SFR Definition 8.3. CPT1CN: Comparator1 Control Bit 7 6 5 4 Name CP1EN CP1OUT CP1RIF CP1FIF CP1HYP[1:0] CP1HYN[1:0] Type R/W R R/W R/W R/W R/W Reset 0 0 0 0 SFR Address = 0x9A; SFR Page = All Pages Bit Name 3 2 0 0 1 0 0 0 Function 7 CP1EN Comparator1 Enable Bit. 0: Comparator1 Disabled. 1: Comparator1 Enabled. 6 CP1OUT Comparator1 Output State Flag. 0: Voltage on CP1+ < CP1–. 1: Voltage on CP1+ > CP1–. 5 CP1RIF Comparator1 Rising-Edge Flag. Must be cleared by software. 0: No Comparator1 Rising Edge has occurred since this flag was last cleared. 1: Comparator1 Rising Edge has occurred. 4 CP1FIF Comparator1 Falling-Edge Flag. Must be cleared by software. 0: No Comparator1 Falling-Edge has occurred since this flag was last cleared. 1: Comparator1 Falling-Edge has occurred. 3:2 CP1HYP[1:0] Comparator1 Positive Hysteresis Control Bits. 00: Positive Hysteresis Disabled. 01: Positive Hysteresis = 5 mV. 10: Positive Hysteresis = 10 mV. 11: Positive Hysteresis = 20 mV. 1:0 CP1HYN[1:0] Comparator1 Negative Hysteresis Control Bits. 00: Negative Hysteresis Disabled. 01: Negative Hysteresis = 5 mV. 10: Negative Hysteresis = 10 mV. 11: Negative Hysteresis = 20 mV. Rev. 1.2 65 C8051F388/9/A/B SFR Definition 8.4. CPT1MD: Comparator1 Mode Selection Bit 7 6 Name 5 4 CP1RIE CP1FIE 3 2 R R R/W R/W R R Reset 0 0 0 0 0 0 Unused Read = 00b, Write = don’t care. 5 CP1RIE Comparator1 Rising-Edge Interrupt Enable. 0: Comparator1 Rising-edge interrupt disabled. 1: Comparator1 Rising-edge interrupt enabled. 4 CP1FIE Comparator1 Falling-Edge Interrupt Enable. 0: Comparator1 Falling-edge interrupt disabled. 1: Comparator1 Falling-edge interrupt enabled. 3:2 Unused Read = 00b, Write = don’t care. 66 R/W 1 Function 7:6 1:0 0 CP1MD[1:0] Type SFR Address = 0x9C; SFR Page = All Pages Bit Name 1 CP1MD[1:0] Comparator1 Mode Select. These bits affect the response time and power consumption for Comparator1. 00: Mode 0 (Fastest Response Time, Highest Power Consumption) 01: Mode 1 10: Mode 2 11: Mode 3 (Slowest Response Time, Lowest Power Consumption) Rev. 1.2 0 C8051F388/9/A/B 8.1. Comparator Multiplexers C8051F388/9/A/B devices include an analog input multiplexer to connect Port I/O pins to the comparator inputs. The Comparator inputs are selected in the CPTnMX registers (SFR Definition 8.5 and SFR Definition 8.6). The CMXnP2–CMXnP0 bits select the Comparator positive input; the CMXnN2–CMXnN0 bits select the Comparator negative input. Important Note About Comparator Inputs: The Port pins selected as comparator inputs should be configured as analog inputs in their associated Port configuration register, and configured to be skipped by the Crossbar (for details on Port configuration, see Section “20.3. General Purpose Port I/O” on page 155). Figure 8.4. Comparator Input Multiplexer Block Diagram Rev. 1.2 67 C8051F388/9/A/B SFR Definition 8.5. CPT0MX: Comparator0 MUX Selection Bit 7 6 Name 5 4 R Reset 0 R/W 0 3 2:0 68 Unused 1 R 0 0 0 R/W 0 0 Function Read = 0b; Write = don’t care. CMX0N[2:0] Comparator0 Negative Input MUX Selection. Unused 0 CMX0P[2:0] SFR Address = 0x9F; SFR Page = All Pages Bit Name 6:4 2 CMX0N[2:0] Type 7 3 Selection 32-pin Package 48-pin Package 000: P1.1 P2.1 001: P1.5 P2.6 010: P2.1 P3.5 011: P2.5 P4.4 100: P0.1 P0.4 101-111: Reserved Reserved Read = 0b; Write = don’t care. CMX0P[2:0] Comparator0 Positive Input MUX Selection. Selection 32-pin Package 48-pin Package 000: P1.0 P2.0 001: P1.4 P2.5 010: P2.0 P3.4 011: P2.4 P4.3 100: P0.0 P0.3 101-111: Reserved Reserved Rev. 1.2 0 C8051F388/9/A/B SFR Definition 8.6. CPT1MX: Comparator1 MUX Selection Bit 7 6 Name 5 4 R Reset 0 R/W 0 3 2:0 Unused 1 R 0 0 CMX1P[2:0] 0 SFR Address = 0x9E; SFR Page = All Pages Bit Name 6:4 2 CMX1N[2:0] Type 7 3 0 R/W 0 0 0 Function Read = 0b; Write = don’t care. CMX1N[2:0] Comparator1 Negative Input MUX Selection. Unused Selection 32-pin Package 48-pin Package 000: P1.3 P2.3 001: P1.7 P3.1 010: P2.3 P4.0 011: Reserved P4.6 100: P0.5 P1.2 101-111: Reserved Reserved Read = 0b; Write = don’t care. CMX1P[2:0] Comparator1 Positive Input MUX Selection. Selection 32-pin Package 48-pin Package 000: P1.2 P2.2 001: P1.6 P3.0 010: P2.2 P3.7 011: Reserved P4.5 100: P0.4 P1.1 101-111: Reserved Reserved Rev. 1.2 69 C8051F388/9/A/B 9. Voltage Regulators (REG0 and REG1) C8051F388/9/A/B devices include two internal voltage regulators: one regulates a voltage source on REGIN to 3.3 V (REG0), and the other regulates the internal core supply to 1.8 V from a VDD supply of 1.8 to 3.6 V (REG1). When enabled, the REG0 output appears on the VDD pin and can be used to power external devices. REG0 can be enabled/disabled by software using bit REG0DIS in register REG01CN (SFR Definition 9.1). REG1 has two power-saving modes built into the regulator to help reduce current consumption in low-power applications. These modes are accessed through the REG01CN register. Electrical characteristics for the on-chip regulators are specified in Table 5.5 on page 37. 9.1. Voltage Regulator (REG0) See “4. Typical Connection Diagrams” for typical connection diagrams using the REG0 voltage regulator. 9.1.1. Regulator Mode Selection REG0 offers a low power mode intended for use when the device is in suspend mode. In this low power mode, the REG0 output remains as specified; however the REG0 dynamic performance (response time) is degraded. See Table 5.5 for normal and low power mode supply current specifications. The REG0 mode selection is controlled via the REG0MD bit in register REG01CN. 9.1.2. External Interrupt 2 (INT2) On C8051F388/9/A/B devices, the VBSTAT bit (register REG01CN) indicates the current logic level of the INT2 signal. If enabled, a INT2 interrupt will be generated when the INT2 signal has either a falling or rising edge. The INT2 interrupt is edge-sensitive, and has no associated interrupt pending flag. See Table 5.3 for INT2 input parameters. 9.2. Voltage Regulator (REG1) Under default conditions, the internal REG1 regulator will remain on when the device enters STOP mode. This allows any enabled reset source to generate a reset for the device and bring the device out of STOP mode. For additional power savings, the STOPCF bit can be used to shut down the regulator and the internal power network of the device when the part enters STOP mode. When STOPCF is set to 1, the RST pin and a full power cycle of the device are the only methods of generating a reset. REG1 offers an additional low power mode intended for use when the device is in suspend mode. This low power mode should not be used during normal operation or if the REG0 Voltage Regulator is disabled. See Table 5.5 for normal and low power mode supply current specifications. The REG1 mode selection is controlled via the REG1MD bit in register REG01CN. Important Note: At least 12 clock instructions must occur after placing REG1 in low power mode before the Internal High Frequency Oscillator is Suspended (OSCICN.5 = 1b). 70 Rev. 1.2 C8051F388/9/A/B SFR Definition 9.1. REG01CN: Voltage Regulator Control Bit 7 6 5 Name REG0DIS INT2STAT Reserved 4 3 2 1 0 REG0MD STOPCF Reserved REG1MD Reserved Type R/W R R/W R/W R/W R/W R/W R/W Reset 0 0 0 0 0 0 0 0 SFR Address = 0xC9; SFR Page = All Pages Bit Name Function 7 REG0DIS Voltage Regulator (REG0) Disable. This bit enables or disables the REG0 Voltage Regulator. 0: Voltage Regulator Enabled. 1: Voltage Regulator Disabled. 6 INT2STAT INT2 Signal Status. This bit indicates the status of the INT2 pin. 0: INT2 pin is currently low. 1: INT2 pin is currently high. 5 Reserved Must Write 0b. 4 REG0MD Voltage Regulator (REG0) Mode Select. This bit selects the Voltage Regulator mode for REG0. When REG0MD is set to 1, the REG0 voltage regulator operates in lower power (suspend) mode. 0: REG0 Voltage Regulator in normal mode. 1: REG0 Voltage Regulator in low power mode. 3 STOPCF Stop Mode Configuration (REG1). This bit configures the REG1 regulator’s behavior when the device enters STOP mode. 0: REG1 Regulator is still active in STOP mode. Any enabled reset source will reset the device. 1: REG1 Regulator is shut down in STOP mode. Only the RST pin or power cycle can reset the device. 2 Reserved Must Write 0b. 1 REG1MD Voltage Regulator (REG1) Mode. This bit selects the Voltage Regulator mode for REG1. When REG1MD is set to 1, the REG1 voltage regulator operates in lower power mode. 0: REG1 Voltage Regulator in normal mode. 1: REG1 Voltage Regulator in low power mode. This bit should not be set to '1' if the REG0 Voltage Regulator is disabled. 0 Reserved Must Write 0b. Rev. 1.2 71 C8051F388/9/A/B 10. Power Management Modes The C8051F388/9/A/B devices have three software programmable power management modes: Idle, Stop, and Suspend. Idle mode and stop mode are part of the standard 8051 architecture, while suspend mode is an enhanced power-saving mode implemented by the high-speed oscillator peripheral. Idle mode halts the CPU while leaving the peripherals and clocks active. In stop mode, the CPU is halted, all interrupts and timers (except the Missing Clock Detector) are inactive, and the internal oscillator is stopped (analog peripherals remain in their selected states; the external oscillator is not affected). Suspend mode is similar to stop mode in that the internal oscillator is halted, but the device can wake on a transition of the INT2 pin. The CPU is not halted in suspend mode, so it can run on another oscillator, if desired. Since clocks are running in Idle mode, power consumption is dependent upon the system clock frequency and the number of peripherals left in active mode before entering Idle. Stop mode and suspend mode consume the least power because the majority of the device is shut down with no clocks active. SFR Definition 10.1 describes the Power Control Register (PCON) used to control the C8051F388/9/A/B's Stop and Idle power management modes. Suspend mode is controlled by the SUSPEND bit in the OSCICN register (SFR Definition 19.3). Although the C8051F388/9/A/B has Idle, Stop, and suspend modes available, more control over the device power can be achieved by enabling/disabling individual peripherals as needed. Each analog peripheral can be disabled when not in use and placed in low power mode. Digital peripherals, such as timers or serial buses, draw little power when they are not in use. Turning off oscillators lowers power consumption considerably, at the expense of reduced functionality. 10.1. Idle Mode Setting the Idle Mode Select bit (PCON.0) causes the hardware to halt the CPU and enter Idle mode as soon as the instruction that sets the bit completes execution. All internal registers and memory maintain their original data. All analog and digital peripherals can remain active during idle mode. Idle mode is terminated when an enabled interrupt is asserted or a reset occurs. The assertion of an enabled interrupt will cause the Idle Mode Selection bit (PCON.0) to be cleared and the CPU to resume operation. The pending interrupt will be serviced and the next instruction to be executed after the return from interrupt (RETI) will be the instruction immediately following the one that set the Idle Mode Select bit. If Idle mode is terminated by an internal or external reset, the CIP-51 performs a normal reset sequence and begins program execution at address 0x0000. Note: If the instruction following the write of the IDLE bit is a single-byte instruction and an interrupt occurs during the execution phase of the instruction that sets the IDLE bit, the CPU may not wake from Idle mode when a future interrupt occurs. Therefore, instructions that set the IDLE bit should be followed by an instruction that has two or more opcode bytes, for example: // in ‘C’: PCON |= 0x01; PCON = PCON; // set IDLE bit // ... followed by a 3-cycle dummy instruction ; in assembly: ORL PCON, #01h MOV PCON, PCON ; set IDLE bit ; ... followed by a 3-cycle dummy instruction If enabled, the Watchdog Timer (WDT) will eventually cause an internal watchdog reset and thereby terminate the Idle mode. This feature protects the system from an unintended permanent shutdown in the event of an inadvertent write to the PCON register. If this behavior is not desired, the WDT may be disabled by software prior to entering the Idle mode if the WDT was initially configured to allow this operation. This provides the opportunity for additional power savings, allowing the system to remain in the Idle mode indefi- 72 Rev. 1.2 C8051F388/9/A/B nitely, waiting for an external stimulus to wake up the system. Refer to Section “17.6. PCA Watchdog Timer Reset” on page 127 for more information on the use and configuration of the WDT. 10.2. Stop Mode Setting the stop mode Select bit (PCON.1) causes the controller core to enter stop mode as soon as the instruction that sets the bit completes execution. In stop mode the internal oscillator, CPU, and all digital peripherals are stopped; the state of the external oscillator circuit is not affected. Each analog peripheral (including the external oscillator circuit) may be shut down individually prior to entering stop mode. Stop mode can only be terminated by an internal or external reset. On reset, the device performs the normal reset sequence and begins program execution at address 0x0000. If enabled, the Missing Clock Detector will cause an internal reset and thereby terminate the stop mode. The Missing Clock Detector should be disabled if the CPU is to be put to in STOP mode for longer than the MCD timeout. By default, when in stop mode the internal regulator is still active. However, the regulator can be configured to shut down while in stop mode to save power. To shut down the regulator in stop mode, the STOPCF bit in register REG01CN should be set to 1 prior to setting the STOP bit (see SFR Definition 9.1). If the regulator is shut down using the STOPCF bit, only the RST pin or a full power cycle are capable of resetting the device. 10.3. Suspend Mode Setting the SUSPEND bit (OSCICN.5) causes the hardware to halt the high-frequency internal oscillator and go into suspend mode as soon as the instruction that sets the bit completes execution. All internal registers and memory maintain their original data. The CPU is not halted in Suspend, so code can still be executed using an oscillator other than the internal high-frequency oscillator. Suspend mode can be terminated by a rising or falling edge on the INT2 pin or a device reset event. When suspend mode is terminated, if the oscillator source is the internal high-frequency oscillator, the device will continue execution on the instruction following the one that set the SUSPEND bit. If the wake event was configured to generate an interrupt, the interrupt will be serviced upon waking the device. If suspend mode is terminated by an internal or external reset, the CIP-51 performs a normal reset sequence and begins program execution at address 0x0000. Rev. 1.2 73 C8051F388/9/A/B SFR Definition 10.1. PCON: Power Control Bit 7 6 5 4 3 2 1 0 Name GF[5:0] STOP IDLE Type R/W R/W R/W 0 0 Reset 0 0 0 0 SFR Address = 0x87; SFR Page = All Pages Bit Name 0 0 Function 7:2 GF[5:0] 1 STOP Stop Mode Select. Setting this bit will place the CIP-51 in stop mode. This bit will always be read as 0. 1: CPU goes into stop mode (internal oscillator stopped). 0 IDLE IDLE: Idle Mode Select. Setting this bit will place the CIP-51 in Idle mode. This bit will always be read as 0. 1: CPU goes into Idle mode. (Shuts off clock to CPU, but clock to Timers, Interrupts, Serial Ports, and Analog Peripherals are still active.) 74 General Purpose Flags 5–0. These are general purpose flags for use under software control. Rev. 1.2 C8051F388/9/A/B 11. CIP-51 Microcontroller The MCU system controller core is the CIP-51 microcontroller. The CIP-51 is fully compatible with the MCS-51™ instruction set; standard 803x/805x assemblers and compilers can be used to develop software. The MCU family has a superset of all the peripherals included with a standard 8051. The CIP-51 also includes on-chip debug hardware (see description in Section 27), and interfaces directly with the analog and digital subsystems providing a complete data acquisition or control-system solution in a single integrated circuit. The CIP-51 Microcontroller core implements the standard 8051 organization and peripherals as well as additional custom peripherals and functions to extend its capability (see Figure 11.1 for a block diagram). The CIP-51 includes the following features:     Fully Compatible with MCS-51 Instruction Set 48 MIPS Peak Throughput with 48 MHz Clock 0 to 48 MHz Clock Frequency Extended Interrupt Handler     Reset Input Power Management Modes On-chip Debug Logic Program and Data Memory Security Performance The CIP-51 employs a pipelined architecture that greatly increases its instruction throughput over the standard 8051 architecture. In a standard 8051, all instructions except for MUL and DIV take 12 or 24 system clock cycles to execute, and usually have a maximum system clock of 12 MHz. By contrast, the CIP-51 core executes 70% of its instructions in one or two system clock cycles, with no instructions taking more than eight system clock cycles. Figure 11.1. CIP-51 Block Diagram Rev. 1.2 75 C8051F388/9/A/B With the CIP-51's maximum system clock at 48 MHz, it has a peak throughput of 48 MIPS. The CIP-51 has a total of 109 instructions. The table below shows the total number of instructions that require each execution time. Clocks to Execute 1 2 2/4 3 3/5 4 5 4/6 6 8 Number of Instructions 26 50 5 10 6 5 2 2 2 1 Programming and Debugging Support In-system programming of the Flash program memory and communication with on-chip debug support logic is accomplished via the Silicon Labs 2-Wire Development Interface (C2). The on-chip debug support logic facilitates full speed in-circuit debugging, allowing the setting of hardware breakpoints, starting, stopping and single stepping through program execution (including interrupt service routines), examination of the program's call stack, and reading/writing the contents of registers and memory. This method of on-chip debugging is completely non-intrusive, requiring no RAM, Stack, timers, or other on-chip resources. C2 details can be found in Section “27. C2 Interface” on page 277. The CIP-51 is supported by development tools from Silicon Labs and third party vendors. Silicon Labs provides an integrated development environment (IDE) including editor, debugger and programmer. The IDE's debugger and programmer interface to the CIP-51 via the C2 interface to provide fast and efficient in-system device programming and debugging. Third party macro assemblers and C compilers are also available. 11.1. Instruction Set The instruction set of the CIP-51 System Controller is fully compatible with the standard MCS-51™ instruction set. Standard 8051 development tools can be used to develop software for the CIP-51. All CIP-51 instructions are the binary and functional equivalent of their MCS-51™ counterparts, including opcodes, addressing modes and effect on PSW flags. However, instruction timing is different than that of the standard 8051. 11.1.1. Instruction and CPU Timing In many 8051 implementations, a distinction is made between machine cycles and clock cycles, with machine cycles varying from 2 to 12 clock cycles in length. However, the CIP-51 implementation is based solely on clock cycle timing. All instruction timings are specified in terms of clock cycles. Due to the pipelined architecture of the CIP-51, most instructions execute in the same number of clock cycles as there are program bytes in the instruction. Conditional branch instructions take one less clock cycle to complete when the branch is not taken as opposed to when the branch is taken. Table 11.1 is the CIP-51 Instruction Set Summary, which includes the mnemonic, number of bytes, and number of clock cycles for each instruction. 76 Rev. 1.2 C8051F388/9/A/B Table 11.1. CIP-51 Instruction Set Summary Mnemonic Arithmetic Operations ADD A, Rn ADD A, direct ADD A, @Ri ADD A, #data ADDC A, Rn ADDC A, direct ADDC A, @Ri ADDC A, #data SUBB A, Rn SUBB A, direct SUBB A, @Ri SUBB A, #data INC A INC Rn INC direct INC @Ri DEC A DEC Rn DEC direct DEC @Ri INC DPTR MUL AB DIV AB DA A Logical Operations ANL A, Rn ANL A, direct ANL A, @Ri ANL A, #data ANL direct, A ANL direct, #data ORL A, Rn ORL A, direct ORL A, @Ri ORL A, #data ORL direct, A ORL direct, #data XRL A, Rn XRL A, direct XRL A, @Ri XRL A, #data XRL direct, A Description Bytes Clock Cycles Add register to A Add direct byte to A Add indirect RAM to A Add immediate to A Add register to A with carry Add direct byte to A with carry Add indirect RAM to A with carry Add immediate to A with carry Subtract register from A with borrow Subtract direct byte from A with borrow Subtract indirect RAM from A with borrow Subtract immediate from A with borrow Increment A Increment register Increment direct byte Increment indirect RAM Decrement A Decrement register Decrement direct byte Decrement indirect RAM Increment Data Pointer Multiply A and B Divide A by B Decimal adjust A 1 2 1 2 1 2 1 2 1 2 1 2 1 1 2 1 1 1 2 1 1 1 1 1 1 2 2 2 1 2 2 2 1 2 2 2 1 1 2 2 1 1 2 2 1 4 8 1 AND Register to A AND direct byte to A AND indirect RAM to A AND immediate to A AND A to direct byte AND immediate to direct byte OR Register to A OR direct byte to A OR indirect RAM to A OR immediate to A OR A to direct byte OR immediate to direct byte Exclusive-OR Register to A Exclusive-OR direct byte to A Exclusive-OR indirect RAM to A Exclusive-OR immediate to A Exclusive-OR A to direct byte 1 2 1 2 2 3 1 2 1 2 2 3 1 2 1 2 2 1 2 2 2 2 3 1 2 2 2 2 3 1 2 2 2 2 Rev. 1.2 77 C8051F388/9/A/B Table 11.1. CIP-51 Instruction Set Summary (Continued) Mnemonic XRL direct, #data CLR A CPL A RL A RLC A RR A RRC A SWAP A Data Transfer MOV A, Rn MOV A, direct MOV A, @Ri MOV A, #data MOV Rn, A MOV Rn, direct MOV Rn, #data MOV direct, A MOV direct, Rn MOV direct, direct MOV direct, @Ri MOV direct, #data MOV @Ri, A MOV @Ri, direct MOV @Ri, #data MOV DPTR, #data16 MOVC A, @A+DPTR MOVC A, @A+PC MOVX A, @Ri MOVX @Ri, A MOVX A, @DPTR MOVX @DPTR, A PUSH direct POP direct XCH A, Rn XCH A, direct XCH A, @Ri XCHD A, @Ri Boolean Manipulation CLR C CLR bit SETB C SETB bit CPL C CPL bit 78 Description Exclusive-OR immediate to direct byte Clear A Complement A Rotate A left Rotate A left through Carry Rotate A right Rotate A right through Carry Swap nibbles of A 3 1 1 1 1 1 1 1 Clock Cycles 3 1 1 1 1 1 1 1 Move Register to A Move direct byte to A Move indirect RAM to A Move immediate to A Move A to Register Move direct byte to Register Move immediate to Register Move A to direct byte Move Register to direct byte Move direct byte to direct byte Move indirect RAM to direct byte Move immediate to direct byte Move A to indirect RAM Move direct byte to indirect RAM Move immediate to indirect RAM Load DPTR with 16-bit constant Move code byte relative DPTR to A Move code byte relative PC to A Move external data (8-bit address) to A Move A to external data (8-bit address) Move external data (16-bit address) to A Move A to external data (16-bit address) Push direct byte onto stack Pop direct byte from stack Exchange Register with A Exchange direct byte with A Exchange indirect RAM with A Exchange low nibble of indirect RAM with A 1 2 1 2 1 2 2 2 2 3 2 3 1 2 2 3 1 1 1 1 1 1 2 2 1 2 1 1 1 2 2 2 1 2 2 2 2 3 2 3 2 2 2 3 3 3 3 3 3 3 2 2 1 2 2 2 Clear Carry Clear direct bit Set Carry Set direct bit Complement Carry Complement direct bit 1 2 1 2 1 2 1 2 1 2 1 2 Rev. 1.2 Bytes C8051F388/9/A/B Table 11.1. CIP-51 Instruction Set Summary (Continued) Mnemonic Description Bytes Clock Cycles 2 2 2 2 2 2 ANL C, bit AND direct bit to Carry 2 ANL C, /bit AND complement of direct bit to Carry 2 ORL C, bit OR direct bit to carry 2 ORL C, /bit OR complement of direct bit to Carry 2 MOV C, bit Move direct bit to Carry 2 MOV bit, C Move Carry to direct bit 2 Program Flow Timings are listed with the PFE on and FLRT = 0. Extra cycles are required for branches if FLRT = 1. JC rel Jump if Carry is set 2 2/4 JNC rel Jump if Carry is not set 2 2/4 JB bit, rel Jump if direct bit is set 3 3/5 JNB bit, rel Jump if direct bit is not set 3 3/5 JBC bit, rel Jump if direct bit is set and clear bit 3 3/5 ACALL addr11 Absolute subroutine call 2 4 LCALL addr16 Long subroutine call 3 5 RET Return from subroutine 1 6 RETI Return from interrupt 1 6 AJMP addr11 Absolute jump 2 4 LJMP addr16 Long jump 3 5 SJMP rel Short jump (relative address) 2 4 JMP @A+DPTR Jump indirect relative to DPTR 1 4 JZ rel Jump if A equals zero 2 2/4 JNZ rel Jump if A does not equal zero 2 2/4 CJNE A, direct, rel Compare direct byte to A and jump if not equal 3 4/6 CJNE A, #data, rel Compare immediate to A and jump if not equal 3 3/5 CJNE Rn, #data, rel Compare immediate to Register and jump if not 3 3/5 equal CJNE @Ri, #data, rel Compare immediate to indirect and jump if not 3 4/6 equal DJNZ Rn, rel Decrement Register and jump if not zero 2 2/4 DJNZ direct, rel Decrement direct byte and jump if not zero 3 3/5 NOP No operation 1 1 Rev. 1.2 79 C8051F388/9/A/B Notes on Registers, Operands and Addressing Modes: Rn - Register R0–R7 of the currently selected register bank. @Ri - Data RAM location addressed indirectly through R0 or R1. rel - 8-bit, signed (two’s complement) offset relative to the first byte of the following instruction. Used by SJMP and all conditional jumps. direct - 8-bit internal data location’s address. This could be a direct-access Data RAM location (0x00– 0x7F) or an SFR (0x80–0xFF). #data - 8-bit constant #data16 - 16-bit constant bit - Direct-accessed bit in Data RAM or SFR addr11 - 11-bit destination address used by ACALL and AJMP. The destination must be within the same 2 kB page of program memory as the first byte of the following instruction. addr16 - 16-bit destination address used by LCALL and LJMP. The destination may be anywhere within the 8 kB program memory space. There is one unused opcode (0xA5) that performs the same function as NOP. All mnemonics copyrighted © Intel Corporation 1980. 80 Rev. 1.2 C8051F388/9/A/B 11.2. CIP-51 Register Descriptions Following are descriptions of SFRs related to the operation of the CIP-51 System Controller. Reserved bits should always be written to the value indicated in the SFR description. Future product versions may use these bits to implement new features in which case the reset value of the bit will be the indicated value, selecting the feature's default state. Detailed descriptions of the remaining SFRs are included in the sections of the datasheet associated with their corresponding system function. SFR Definition 11.1. DPL: Data Pointer Low Byte Bit 7 6 5 4 Name DPL[7:0] Type R/W Reset 0 0 0 0 SFR Address = 0x82; SFR Page = All Pages Bit Name 7:0 DPL[7:0] 3 2 1 0 0 0 0 0 3 2 1 0 0 0 0 0 Function Data Pointer Low. The DPL register is the low byte of the 16-bit DPTR. SFR Definition 11.2. DPH: Data Pointer High Byte Bit 7 6 5 4 Name DPH[7:0] Type R/W Reset 0 0 0 0 SFR Address = 0x83; SFR Page = All Pages Bit Name 7:0 DPH[7:0] Function Data Pointer High. The DPH register is the high byte of the 16-bit DPTR. Rev. 1.2 81 C8051F388/9/A/B SFR Definition 11.3. SP: Stack Pointer Bit 7 6 5 4 Name SP[7:0] Type R/W Reset 0 0 0 0 SFR Address = 0x81; SFR Page = All Pages Bit Name 7:0 SP[7:0] 3 2 1 0 0 1 1 1 Function Stack Pointer. The Stack Pointer holds the location of the top of the stack. The stack pointer is incremented before every PUSH operation. The SP register defaults to 0x07 after reset. SFR Definition 11.4. ACC: Accumulator Bit 7 6 5 4 Name ACC[7:0] Type R/W Reset 0 0 0 0 3 2 1 0 0 0 0 0 SFR Address = 0xE0; SFR Page = All Pages; Bit-Addressable Bit Name Function 7:0 ACC[7:0] Accumulator. This register is the accumulator for arithmetic operations. SFR Definition 11.5. B: B Register Bit 7 6 5 4 Name B[7:0] Type R/W Reset 0 0 0 0 3 2 1 0 0 0 0 0 SFR Address = 0xF0; SFR Page = All Pages; Bit-Addressable Bit Name Function 7:0 82 B[7:0] B Register. This register serves as a second accumulator for certain arithmetic operations. Rev. 1.2 C8051F388/9/A/B SFR Definition 11.6. PSW: Program Status Word Bit 7 6 5 Name CY AC F0 Type R/W R/W R/W Reset 0 0 0 4 3 2 1 0 RS[1:0] OV F1 PARITY R/W R/W R/W R 0 0 0 0 0 SFR Address = 0xD0; SFR Page = All Pages; Bit-Addressable Bit Name Function 7 CY Carry Flag. This bit is set when the last arithmetic operation resulted in a carry (addition) or a borrow (subtraction). It is cleared to logic 0 by all other arithmetic operations. 6 AC Auxiliary Carry Flag. This bit is set when the last arithmetic operation resulted in a carry into (addition) or a borrow from (subtraction) the high order nibble. It is cleared to logic 0 by all other arithmetic operations. 5 F0 User Flag 0. This is a bit-addressable, general purpose flag for use under software control. 4:3 RS[1:0] 2 OV Register Bank Select. These bits select which register bank is used during register accesses. 00: Bank 0, Addresses 0x00-0x07 01: Bank 1, Addresses 0x08-0x0F 10: Bank 2, Addresses 0x10-0x17 11: Bank 3, Addresses 0x18-0x1F Overflow Flag. This bit is set to 1 under the following circumstances: An ADD, ADDC, or SUBB instruction causes a sign-change overflow. MUL instruction results in an overflow (result is greater than 255). A DIV instruction causes a divide-by-zero condition. A The OV bit is cleared to 0 by the ADD, ADDC, SUBB, MUL, and DIV instructions in all other cases. 1 F1 0 PARITY User Flag 1. This is a bit-addressable, general purpose flag for use under software control. Parity Flag. This bit is set to logic 1 if the sum of the eight bits in the accumulator is odd and cleared if the sum is even. Rev. 1.2 83 C8051F388/9/A/B 12. Prefetch Engine The C8051F388/9/A/B family of devices incorporate a 2-byte prefetch engine. Because the access time of the Flash memory is 40 ns, and the minimum instruction time is roughly 20 ns, the prefetch engine is necessary for code execution above 25 MHz. When operating at speeds greater than 25 MHz, the prefetch engine must be enabled by setting PFE0CN.PFEN and FLSCL.FLRT to 1. Instructions are read from Flash memory two bytes at a time by the prefetch engine and given to the CIP-51 processor core to execute. When running linear code (code without any jumps or branches), the prefetch engine allows instructions to be executed at full speed. When a code branch occurs, the processor may be stalled for up to two clock cycles while the next set of code bytes is retrieved from Flash memory. It is recommended that the prefetch be used for optimal code execution timing. Note: The prefetch engine can be disabled when the device is in suspend mode to save power. SFR Definition 12.1. PFE0CN: Prefetch Engine Control Bit 7 6 Name 5 4 3 2 1 PFEN 0 FLBWE Type R R R/W R R R R R/W Reset 0 0 1 0 0 0 0 0 SFR Address = 0xAF; SFR Page = All Pages Bit Name Function 7:6 Unused 5 PFEN 4:1 Unused Read = 0000b. Write = don’t care. 0 FLBWE Flash Block Write Enable. This bit allows block writes to Flash memory from software. 0: Each byte of a software Flash write is written individually. 1: Flash bytes are written in groups of two. 84 Read = 00b, Write = don’t care. Prefetch Enable. This bit enables the prefetch engine. 0: Prefetch engine is disabled. 1: Prefetch engine is enabled. Rev. 1.2 C8051F388/9/A/B 13. Memory Organization The memory organization of the CIP-51 System Controller is similar to that of a standard 8051. There are two separate memory spaces: program memory and data memory. Program and data memory share the same address space but are accessed via different instruction types. The CIP-51 memory organization is shown in Figure 13.1 and Figure 13.2. Figure 13.1. On-Chip Memory Map for 64 kB Devices (C8051F388/9) Rev. 1.2 85 C8051F388/9/A/B Figure 13.2. On-Chip Memory Map for 32 kB Devices (C8051F38A/B) 13.1. Program Memory The CIP-51 core has a 64k-byte program memory space. The C8051F388/9/A/B implements 64 or 32 kB of this program memory space as in-system, re-programmable Flash memory. Note that on the C8051F388/9 (64 kB version), addresses above 0xFBFF are reserved. Program memory is normally assumed to be read-only. However, the CIP-51 can write to program memory by setting the Program Store Write Enable bit (PSCTL.0) and using the MOVX instruction. This feature provides a mechanism for the CIP-51 to update program code and use the program memory space for nonvolatile data storage. Refer to Section “18. Flash Memory” on page 129 for further details. 13.2. Data Memory The CIP-51 includes 256 of internal RAM mapped into the data memory space from 0x00 through 0xFF. The lower 128 bytes of data memory are used for general purpose registers and scratch pad memory. Either direct or indirect addressing may be used to access the lower 128 bytes of data memory. Locations 0x00 through 0x1F are addressable as four banks of general purpose registers, each bank consisting of eight byte-wide registers. The next 16 bytes, locations 0x20 through 0x2F, may either be addressed as bytes or as 128 bit locations accessible with the direct addressing mode. 86 Rev. 1.2 C8051F388/9/A/B The upper 128 bytes of data memory are accessible only by indirect addressing. This region occupies the same address space as the Special Function Registers (SFR) but is physically separate from the SFR space. The addressing mode used by an instruction when accessing locations above 0x7F determines whether the CPU accesses the upper 128 bytes of data memory space or the SFRs. Instructions that use direct addressing will access the SFR space. Instructions using indirect addressing above 0x7F access the upper 128 bytes of data memory. Figure 13.1 illustrates the data memory organization of the CIP-51. 13.3. General Purpose Registers The lower 32 bytes of data memory, locations 0x00 through 0x1F, may be addressed as four banks of general-purpose registers. Each bank consists of eight byte-wide registers designated R0 through R7. Only one of these banks may be enabled at a time. Two bits in the program status word, RS0 (PSW.3) and RS1 (PSW.4), select the active register bank (see description of the PSW in SFR Definition 11.6). This allows fast context switching when entering subroutines and interrupt service routines. Indirect addressing modes use registers R0 and R1 as index registers. 13.4. Bit Addressable Locations In addition to direct access to data memory organized as bytes, the sixteen data memory locations at 0x20 through 0x2F are also accessible as 128 individually addressable bits. Each bit has a bit address from 0x00 to 0x7F. Bit 0 of the byte at 0x20 has bit address 0x00 while bit7 of the byte at 0x20 has bit address 0x07. Bit 7 of the byte at 0x2F has bit address 0x7F. A bit access is distinguished from a full byte access by the type of instruction used (bit source or destination operands as opposed to a byte source or destination). The MCS-51™ assembly language allows an alternate notation for bit addressing of the form XX.B where XX is the byte address and B is the bit position within the byte. For example, the instruction: MOV C, 22h.3 moves the Boolean value at 0x13 (bit 3 of the byte at location 0x22) into the Carry flag. 13.5. Stack A programmer's stack can be located anywhere in the 256-byte data memory. The stack area is designated using the Stack Pointer (SP, 0x81) SFR. The SP will point to the last location used. The next value pushed on the stack is placed at SP+1 and then SP is incremented. A reset initializes the stack pointer to location 0x07. Therefore, the first value pushed on the stack is placed at location 0x08, which is also the first register (R0) of register bank 1. Thus, if more than one register bank is to be used, the SP should be initialized to a location in the data memory not being used for data storage. The stack depth can extend up to 256 bytes. Rev. 1.2 87 C8051F388/9/A/B 14. External Data Memory Interface and On-Chip XRAM The chip includes 4 kB (C8051F388/9) or 2 kB (C8051F38A/B) of RAM on-chip, and is mapped into the external data memory space (XRAM). Additionally, an External Memory Interface (EMIF) is available on the C8051F388/A devices, which can be used to access off-chip data memories and memory-mapped devices connected to the GPIO ports. The external memory space may be accessed using the external move instruction (MOVX) and the data pointer (DPTR), or using the MOVX indirect addressing mode using R0 or R1. If the MOVX instruction is used with an 8-bit address operand (such as @R1), then the high byte of the 16-bit address is provided by the External Memory Interface Control Register (EMI0CN, shown in SFR Definition 14.1). Note: the MOVX instruction can also be used for writing to the FLASH memory. See Section “18. Flash Memory” on page 129 for details. The MOVX instruction accesses XRAM by default. 14.1. Accessing XRAM The XRAM memory space is accessed using the MOVX instruction. The MOVX instruction has two forms, both of which use an indirect addressing method. The first method uses the Data Pointer, DPTR, a 16-bit register which contains the effective address of the XRAM location to be read from or written to. The second method uses R0 or R1 in combination with the EMI0CN register to generate the effective XRAM address. Examples of both of these methods are given below. 14.1.1. 16-Bit MOVX Example The 16-bit form of the MOVX instruction accesses the memory location pointed to by the contents of the DPTR register. The following series of instructions reads the value of the byte at address 0x1234 into the accumulator A: MOV MOVX DPTR, #1234h A, @DPTR ; load DPTR with 16-bit address to read (0x1234) ; load contents of 0x1234 into accumulator A The above example uses the 16-bit immediate MOV instruction to set the contents of DPTR. Alternately, the DPTR can be accessed through the SFR registers DPH, which contains the upper 8-bits of DPTR, and DPL, which contains the lower 8-bits of DPTR. 14.1.2. 8-Bit MOVX Example The 8-bit form of the MOVX instruction uses the contents of the EMI0CN SFR to determine the upper 8-bits of the effective address to be accessed and the contents of R0 or R1 to determine the lower 8-bits of the effective address to be accessed. The following series of instructions read the contents of the byte at address 0x1234 into the accumulator A. MOV MOV MOVX 88 EMI0CN, #12h R0, #34h a, @R0 ; load high byte of address into EMI0CN ; load low byte of address into R0 (or R1) ; load contents of 0x1234 into accumulator A Rev. 1.2 C8051F388/9/A/B 14.2. Configuring the External Memory Interface Configuring the External Memory Interface consists of five steps: 1. Configure the Output Modes of the associated port pins as either push-pull or open-drain (push-pull is most common), and skip the associated pins in the crossbar. 2. Configure Port latches to “park” the EMIF pins in a dormant state (usually by setting them to logic 1). 3. Select Multiplexed mode or Non-multiplexed mode. 4. Select the memory mode (on-chip only, split mode without bank select, split mode with bank select, or off-chip only). 5. Set up timing to interface with off-chip memory or peripherals. Each of these five steps is explained in detail in the following sections. The Port selection, Multiplexed mode selection, and Mode bits are located in the EMI0CF register shown in SFR Definition 14.4. 14.3. Port Configuration The External Memory Interface appears on Ports 4, 3, 2, and 1 when it is used for off-chip memory access. When the EMIF is used, the Crossbar should be configured to skip over the control lines P1.7 (WR), P1.6 (RD), and if multiplexed mode is selected P1.3 (ALE) using the P1SKIP register. For more information about configuring the Crossbar, see Section “Figure 20.1. Port I/O Functional Block Diagram (Port 0 through Port 3)” on page 147. The External Memory Interface claims the associated Port pins for memory operations ONLY during the execution of an off-chip MOVX instruction. Once the MOVX instruction has completed, control of the Port pins reverts to the Port latches or to the Crossbar settings for those pins. See Section “20. Port Input/Output” on page 147 for more information about the Crossbar and Port operation and configuration. The Port latches should be explicitly configured to ‘park’ the External Memory Interface pins in a dormant state, most commonly by setting them to a logic 1. During the execution of the MOVX instruction, the External Memory Interface will explicitly disable the drivers on all Port pins that are acting as Inputs (Data[7:0] during a READ operation, for example). The Output mode of the Port pins (whether the pin is configured as Open-Drain or Push-Pull) is unaffected by the External Memory Interface operation, and remains controlled by the PnMDOUT registers. In most cases, the output modes of all EMIF pins should be configured for push-pull mode. Rev. 1.2 89 C8051F388/9/A/B SFR Definition 14.1. EMI0CN: External Memory Interface Control Bit 7 6 5 4 3 Name PGSEL[7:0] Type R/W Reset 0 0 0 0 SFR Address = 0xAA; SFR Page = All Pages Bit Name 7:0 90 PGSEL[7:0] 0 2 1 0 0 0 0 Function XRAM Page Select Bits. The XRAM Page Select Bits provide the high byte of the 16-bit external data memory address when using an 8-bit MOVX command, effectively selecting a 256-byte page of RAM. 0x00: 0x0000 to 0x00FF 0x01: 0x0100 to 0x01FF ... 0xFE: 0xFE00 to 0xFEFF 0xFF: 0xFF00 to 0xFFFF Rev. 1.2 C8051F388/9/A/B SFR Definition 14.2. EMI0CF: External Memory Interface Configuration Bit 7 Name 6 5 Reserved 4 3 2 1 0 EMD2 EMD[1:0] EALE[1:0] R/W R/W Type R R/W R R/W Reset 0 0 0 0 SFR Address = 0x85; SFR Page = All Pages Bit Name 0 0 1 1 Function 7 Unused Read = 0b; Write = don’t care. 6 Reserved 5 Unused 4 EMD2 3:2 EMD[1:0] EMIF Operating Mode Select. These bits control the operating mode of the External Memory Interface. 00: Internal Only: MOVX accesses on-chip XRAM only. All effective addresses alias to on-chip memory space. 01: Split Mode without Bank Select: Accesses below the on-chip XRAM boundary are directed on-chip. Accesses above the on-chip XRAM boundary are directed off-chip. 8-bit off-chip MOVX operations use the current contents of the Address High port latches to resolve upper address byte. Note that in order to access off-chip space, EMI0CN must be set to a page that is not contained in the on-chip address space. 10: Split Mode with Bank Select: Accesses below the on-chip XRAM boundary are directed on-chip. Accesses above the on-chip XRAM boundary are directed off-chip. 8-bit off-chip MOVX operations use the contents of EMI0CN to determine the high-byte of the address. 11: External Only: MOVX accesses off-chip XRAM only. On-chip XRAM is not visible to the CPU. 1:0 EALE[1:0] ALE Pulse-Width Select Bits (only has effect when EMD2 = 0). 00: ALE high and ALE low pulse width = 1 SYSCLK cycle. 01: ALE high and ALE low pulse width = 2 SYSCLK cycles. 10: ALE high and ALE low pulse width = 3 SYSCLK cycles. 11: ALE high and ALE low pulse width = 4 SYSCLK cycles. Read = 0b; Must Write 0b. Read = 0b; Write = don’t care. EMIF Multiplex Mode Select. 0: EMIF operates in multiplexed address/data mode. 1: EMIF operates in non-multiplexed mode (separate address and data pins). Rev. 1.2 91 C8051F388/9/A/B 14.4. Multiplexed and Non-multiplexed Selection The External Memory Interface is capable of acting in a Multiplexed mode or a Non-multiplexed mode, depending on the state of the EMD2 (EMI0CF.4) bit. 14.4.1. Multiplexed Configuration In Multiplexed mode, the Data Bus and the lower 8-bits of the Address Bus share the same Port pins: AD[7:0]. In this mode, an external latch (74HC373 or equivalent logic gate) is used to hold the lower 8-bits of the RAM address. The external latch is controlled by the ALE (Address Latch Enable) signal, which is driven by the External Memory Interface logic. An example of a Multiplexed Configuration is shown in Figure 14.1. In Multiplexed mode, the external MOVX operation can be broken into two phases delineated by the state of the ALE signal. During the first phase, ALE is high and the lower 8-bits of the Address Bus are presented to AD[7:0]. During this phase, the address latch is configured such that the ‘Q’ outputs reflect the states of the ‘D’ inputs. When ALE falls, signaling the beginning of the second phase, the address latch outputs remain fixed and are no longer dependent on the latch inputs. Later in the second phase, the Data Bus controls the state of the AD[7:0] port at the time RD or WR is asserted. See Section “14.6.2. Multiplexed Mode” on page 101 for more information. Figure 14.1. Multiplexed Configuration Example 92 Rev. 1.2 C8051F388/9/A/B 14.4.2. Non-multiplexed Configuration In Non-multiplexed mode, the Data Bus and the Address Bus pins are not shared. An example of a Non-multiplexed Configuration is shown in Figure 14.2. See Section “14.6.1. Non-multiplexed Mode” on page 98 for more information about Non-multiplexed operation. Figure 14.2. Non-multiplexed Configuration Example Rev. 1.2 93 C8051F388/9/A/B 14.5. Memory Mode Selection The external data memory space can be configured in one of four modes, shown in Figure 14.3, based on the EMIF Mode bits in the EMI0CF register (SFR Definition 14.4). These modes are summarized below. More information about the different modes can be found in Section “14.6. Timing” on page 96. Figure 14.3. EMIF Operating Modes 14.5.1. Internal XRAM Only When EMI0CF.[3:2] are set to 00, all MOVX instructions will target the internal XRAM space on the device. Memory accesses to addresses beyond the populated space will wrap on 2k or 4k boundaries (depending on the RAM available on the device). As an example, the addresses 0x1000 and 0x2000 both evaluate to address 0x0000 in on-chip XRAM space. 8-bit MOVX operations use the contents of EMI0CN to determine the high-byte of the effective address and R0 or R1 to determine the low-byte of the effective address.  16-bit MOVX operations use the contents of the 16-bit DPTR to determine the effective address. 14.5.2. Split Mode without Bank Select When EMI0CF.[3:2] are set to 01, the XRAM memory map is split into two areas, on-chip space and off-chip space.      94 Effective addresses below the internal XRAM size boundary will access on-chip XRAM space. Effective addresses above the internal XRAM size boundary will access off-chip space. 8-bit MOVX operations use the contents of EMI0CN to determine whether the memory access is on-chip or off-chip. However, in the “No Bank Select” mode, an 8-bit MOVX operation will not drive the upper 8-bits A[15:8] of the Address Bus during an off-chip access. This allows the user to manipulate the upper address bits at will by setting the Port state directly via the port latches. This behavior is in contrast with “Split Mode with Bank Select” described below. The lower 8-bits of the Address Bus A[7:0] are driven, determined by R0 or R1. 16-bit MOVX operations use the contents of DPTR to determine whether the memory access is on-chip or off-chip, and unlike 8-bit MOVX operations, the full 16-bits of the Address Bus A[15:0] are driven during the off-chip transaction. Rev. 1.2 C8051F388/9/A/B 14.5.3. Split Mode with Bank Select When EMI0CF.[3:2] are set to 10, the XRAM memory map is split into two areas, on-chip space and off-chip space. Effective addresses below the internal XRAM size boundary will access on-chip XRAM space. Effective addresses above the internal XRAM size boundary will access off-chip space.  8-bit MOVX operations use the contents of EMI0CN to determine whether the memory access is on-chip or off-chip. The upper 8-bits of the Address Bus A[15:8] are determined by EMI0CN, and the lower 8-bits of the Address Bus A[7:0] are determined by R0 or R1. All 16-bits of the Address Bus A[15:0] are driven in “Bank Select” mode.  16-bit MOVX operations use the contents of DPTR to determine whether the memory access is on-chip or off-chip, and the full 16-bits of the Address Bus A[15:0] are driven during the off-chip transaction. 14.5.4. External Only When EMI0CF[3:2] are set to 11, all MOVX operations are directed to off-chip space. On-chip XRAM is not visible to the CPU. This mode is useful for accessing off-chip memory located between 0x0000 and the internal XRAM size boundary.     8-bit MOVX operations ignore the contents of EMI0CN. The upper Address bits A[15:8] are not driven (identical behavior to an off-chip access in “Split Mode without Bank Select” described above). This allows the user to manipulate the upper address bits at will by setting the Port state directly. The lower 8-bits of the effective address A[7:0] are determined by the contents of R0 or R1. 16-bit MOVX operations use the contents of DPTR to determine the effective address A[15:0]. The full 16-bits of the Address Bus A[15:0] are driven during the off-chip transaction. Rev. 1.2 95 C8051F388/9/A/B 14.6. Timing The timing parameters of the External Memory Interface can be configured to enable connection to devices having different setup and hold time requirements. The Address Setup time, Address Hold time, RD and WR strobe widths, and in multiplexed mode, the width of the ALE pulse are all programmable in units of SYSCLK periods through EMI0TC, shown in SFR Definition 14.3, and EMI0CF[1:0]. The timing for an off-chip MOVX instruction can be calculated by adding 4 SYSCLK cycles to the timing parameters defined by the EMI0TC register. Assuming non-multiplexed operation, the minimum execution time for an off-chip XRAM operation is 5 SYSCLK cycles (1 SYSCLK for RD or WR pulse + 4 SYSCLKs). For multiplexed operations, the Address Latch Enable signal will require a minimum of 2 additional SYSCLK cycles. Therefore, the minimum execution time for an off-chip XRAM operation in multiplexed mode is 7 SYSCLK cycles (2 for ALE + 1 for RD or WR + 4). The programmable setup and hold times default to the maximum delay settings after a reset. Table 14.1 lists the AC parameters for the External Memory Interface, and Figure 14.4 through Figure 14.9 show the timing diagrams for the different External Memory Interface modes and MOVX operations. 96 Rev. 1.2 C8051F388/9/A/B SFR Definition 14.3. EMI0TC: External Memory Timing Control Bit 7 6 5 4 3 2 1 0 Name EAS[1:0] EWR[3:0] EAH[1:0] Type R/W R/W R/W Reset 1 1 1 1 SFR Address = 0x84; SFR Page = All Pages Bit Name 1 1 1 1 Function 7:6 EAS[1:0] EMIF Address Setup Time Bits. 00: Address setup time = 0 SYSCLK cycles. 01: Address setup time = 1 SYSCLK cycle. 10: Address setup time = 2 SYSCLK cycles. 11: Address setup time = 3 SYSCLK cycles. 5:2 EWR[3:0] EMIF WR and RD Pulse-Width Control Bits. 0000: WR and RD pulse width = 1 SYSCLK cycle. 0001: WR and RD pulse width = 2 SYSCLK cycles. 0010: WR and RD pulse width = 3 SYSCLK cycles. 0011: WR and RD pulse width = 4 SYSCLK cycles. 0100: WR and RD pulse width = 5 SYSCLK cycles. 0101: WR and RD pulse width = 6 SYSCLK cycles. 0110: WR and RD pulse width = 7 SYSCLK cycles. 0111: WR and RD pulse width = 8 SYSCLK cycles. 1000: WR and RD pulse width = 9 SYSCLK cycles. 1001: WR and RD pulse width = 10 SYSCLK cycles. 1010: WR and RD pulse width = 11 SYSCLK cycles. 1011: WR and RD pulse width = 12 SYSCLK cycles. 1100: WR and RD pulse width = 13 SYSCLK cycles. 1101: WR and RD pulse width = 14 SYSCLK cycles. 1110: WR and RD pulse width = 15 SYSCLK cycles. 1111: WR and RD pulse width = 16 SYSCLK cycles. 1:0 EAH[1:0] EMIF Address Hold Time Bits. 00: Address hold time = 0 SYSCLK cycles. 01: Address hold time = 1 SYSCLK cycle. 10: Address hold time = 2 SYSCLK cycles. 11: Address hold time = 3 SYSCLK cycles. Rev. 1.2 97 C8051F388/9/A/B 14.6.1. Non-multiplexed Mode 14.6.1.1. 16-bit MOVX: EMI0CF[4:2] = 101, 110, or 111 Figure 14.4. Non-Multiplexed 16-bit MOVX Timing 98 Rev. 1.2 C8051F388/9/A/B 14.6.1.2. 8-bit MOVX without Bank Select: EMI0CF[4:2] = 101 or 111 Figure 14.5. Non-Multiplexed 8-bit MOVX without Bank Select Timing Rev. 1.2 99 C8051F388/9/A/B 14.6.1.3. 8-bit MOVX with Bank Select: EMI0CF[4:2] = 110 Figure 14.6. Non-Multiplexed 8-bit MOVX with Bank Select Timing 100 Rev. 1.2 C8051F388/9/A/B 14.6.2. Multiplexed Mode 14.6.2.1. 16-bit MOVX: EMI0CF[4:2] = 001, 010, or 011 Figure 14.7. Multiplexed 16-bit MOVX Timing Rev. 1.2 101 C8051F388/9/A/B 14.6.2.2. 8-bit MOVX without Bank Select: EMI0CF[4:2] = 001 or 011 Figure 14.8. Multiplexed 8-bit MOVX without Bank Select Timing 102 Rev. 1.2 C8051F388/9/A/B 14.6.2.3. 8-bit MOVX with Bank Select: EMI0CF[4:2] = 010 Figure 14.9. Multiplexed 8-bit MOVX with Bank Select Timing Rev. 1.2 103 C8051F388/9/A/B Table 14.1. AC Parameters for External Memory Interface Parameter Description Min* Max* Units TACS Address/Control Setup Time 0 3 x TSYSCLK ns TACW Address/Control Pulse Width 1 x TSYSCLK 16 x TSYSCLK ns TACH Address/Control Hold Time 0 3 x TSYSCLK ns TALEH Address Latch Enable High Time 1 x TSYSCLK 4 x TSYSCLK ns TALEL Address Latch Enable Low Time 1 x TSYSCLK 4 x TSYSCLK ns TWDS Write Data Setup Time 1 x TSYSCLK 19 x TSYSCLK ns TWDH Write Data Hold Time 0 3 x TSYSCLK ns TRDS Read Data Setup Time 20 ns TRDH Read Data Hold Time 0 ns Note: TSYSCLK is equal to one period of the device system clock (SYSCLK). 104 Rev. 1.2 C8051F388/9/A/B 15. Special Function Registers The direct-access data memory locations from 0x80 to 0xFF constitute the special function registers (SFRs). The SFRs provide control and data exchange with the C8051F388/9/A/B's resources and peripherals. The CIP-51 controller core duplicates the SFRs found in a typical 8051 implementation as well as implementing additional SFRs used to configure and access the sub-systems unique to the C8051F388/9/A/B. This allows the addition of new functionality while retaining compatibility with the MCS51™ instruction set. Table 15.1 lists the SFRs implemented in the C8051F388/9/A/B device family. The SFR registers are accessed anytime the direct addressing mode is used to access memory locations from 0x80 to 0xFF. SFRs with addresses ending in 0x0 or 0x8 (e.g. P0, TCON, SCON0, IE, etc.) are bitaddressable as well as byte-addressable. All other SFRs are byte-addressable only. Unoccupied addresses in the SFR space are reserved for future use. Accessing these areas will have an indeterminate effect and should be avoided. Refer to the corresponding pages of the data sheet, as indicated in Table 15.2, for a detailed description of each register. 15.1. SFR Paging The CIP-51 features SFR paging, allowing the device to map many SFRs into the 0x80 to 0xFF memory address space. The SFR memory space has 256 pages. In this way, each memory location from 0x80 to 0xFF can access up to 256 SFRs. The C8051F388/9/A/B devices utilize two SFR pages: 0x0, and 0xF. Most SFRs are available on both pages. SFR pages are selected using the Special Function Register Page Selection register, SFRPAGE. The procedure for reading and writing an SFR is as follows: 1. Select the appropriate SFR page number using the SFRPAGE register. 2. Use direct accessing mode to read or write the special function register (MOV instruction). Important Note: When reading or writing SFRs that are not available on all pages within an ISR, it is recommended to save the state of the SFRPAGE register on ISR entry, and restore state on exit. SFR Definition 15.1. SFRPAGE: SFR Page Bit 7 6 5 4 3 Name SFRPAGE[7:0] Type R/W Reset 0 0 0 0 SFR Address = 0xBF; SFR Page = All Pages Bit Name 7:0 SFRPAGE[7:0] 0 2 1 0 0 0 0 Function SFR Page Bits. Represents the SFR Page the C8051 core uses when reading or modifying SFRs. Write: Sets the SFR Page. Read: Byte is the SFR page the C8051 core is using. Rev. 1.2 105 C8051F388/9/A/B Page Address Table 15.1. Special Function Register (SFR) Memory Map F8 F0 E8 E0 0 F D8 D0 0 F 0 C0 F 0 B8 F B0 A8 A0 98 0 90 F 88 80 C8 0(8) 1(9) 2(A) 3(B) 4(C) 5(D) 6(E) 7(F) SPI0CN PCA0L PCA0H PCA0CPL0 PCA0CPH0 PCA0CPL4 PCA0CPH4 VDM0CN B P0MDIN P1MDIN P2MDIN P3MDIN P4MDIN EIP1 EIP2 ADC0CN PCA0CPL1 PCA0CPH1 PCA0CPL2 PCA0CPH2 PCA0CPL3 PCA0CPH3 RSTSRC IT01CF ACC XBR0 XBR1 XBR2 SMOD1 EIE1 EIE2 CKCON1 PCA0CN PCA0MD PCA0CPM0 PCA0CPM1 PCA0CPM2 PCA0CPM3 PCA0CPM4 P3SKIP PSW REF0CN SCON1 SBUF1 P0SKIP P1SKIP P2SKIP TMR2CN TMR2RLL TMR2RLH TMR2L TMR2H SMB0ADM SMB0ADR REG01CN TMR5CN TMR5RLL TMR5RLH TMR5L TMR5H SMB1ADM SMB1ADR SMB0CN SMB0CF SMB0DAT ADC0GTL ADC0GTH ADC0LTL ADC0LTH P4 SMB1CN SMB1CF SMB1DAT CLKMUL ADC0CF IP AMX0N AMX0P ADC0L ADC0H SFRPAGE SMBTC P3 OSCXCN OSCICN OSCICL SBRLL1 SBRLH1 FLSCL FLKEY IE CLKSEL EMI0CN SBCON1 P4MDOUT PFE0CN P2 SPI0CFG SPI0CKR SPI0DAT P0MDOUT P1MDOUT P2MDOUT P3MDOUT SCON0 SBUF0 CPT1CN CPT0CN CPT1MD CPT0MD CPT1MX CPT0MX TMR3CN TMR3RLL TMR3RLH TMR3L TMR3H P1 TMR4CN TMR4RLL TMR4RLH TMR4L TMR4H TCON TMOD TL0 TL1 TH0 TH1 CKCON PSCTL P0 SP DPL DPH EMI0TC EMI0CF OSCLCN PCON 0(8) 1(9) 2(A) 3(B) 4(C) 5(D) 6(E) 7(F) Notes: 1. SFR Addresses ending in 0x0 or 0x8 are bit-addressable locations and can be used with bitwise instructions. 2. Unless indicated otherwise, SFRs are available on both page 0 and page F. 106 Rev. 1.2 C8051F388/9/A/B Table 15.2. Special Function Registers SFRs are listed in alphabetical order. All undefined SFR locations are reserved Register ACC Address Page 0xE0 All Pages Accumulator Description Page 82 ADC0CF 0xBC All Pages ADC0 Configuration 49 ADC0CN 0xE8 All Pages ADC0 Control 51 ADC0GTH 0xC4 All Pages ADC0 Greater-Than Compare High 52 ADC0GTL 0xC3 All Pages ADC0 Greater-Than Compare Low 52 ADC0H 0xBE All Pages ADC0 High 50 ADC0L 0xBD All Pages ADC0 Low 50 ADC0LTH 0xC6 All Pages ADC0 Less-Than Compare Word High 53 ADC0LTL 0xC5 All Pages ADC0 Less-Than Compare Word Low 53 AMX0N 0xBA All Pages AMUX0 Negative Channel Select 57 AMX0P 0xBB All Pages AMUX0 Positive Channel Select 56 B 0xF0 All Pages B Register 82 CKCON 0x8E All Pages Clock Control 225 CKCON1 0xE4 F Clock Control 1 226 CLKMUL 0xB9 0 Clock Multiplier 141 CLKSEL 0xA9 All Pages Clock Select 138 CPT0CN 0x9B All Pages Comparator0 Control 63 CPT0MD 0x9D All Pages Comparator0 Mode Selection 64 CPT0MX 0x9F All Pages Comparator0 MUX Selection 68 CPT1CN 0x9A All Pages Comparator1 Control 65 CPT1MD 0x9C All Pages Comparator1 Mode Selection 66 CPT1MX 0x9E All Pages Comparator1 MUX Selection 69 DPH 0x83 All Pages Data Pointer High 81 DPL 0x82 All Pages Data Pointer Low 81 EIE1 0xE6 All Pages Extended Interrupt Enable 1 117 EIE2 0xE7 All Pages Extended Interrupt Enable 2 119 EIP1 0xF6 All Pages Extended Interrupt Priority 1 118 EIP2 0xF7 All Pages Extended Interrupt Priority 2 120 EMI0CF 0x85 All Pages External Memory Interface Configuration 91 EMI0CN 0xAA All Pages External Memory Interface Control 90 EMI0TC 0x84 All Pages External Memory Interface Timing 97 FLKEY 0xB7 All Pages Flash Lock and Key 134 FLSCL 0xB6 All Pages Flash Scale 135 Rev. 1.2 107 C8051F388/9/A/B Table 15.2. Special Function Registers (Continued) SFRs are listed in alphabetical order. All undefined SFR locations are reserved Register Address Page Description Page IE 0xA8 All Pages Interrupt Enable 115 IP 0xB8 All Pages Interrupt Priority 116 IT01CF 0xE4 OSCICL 0xB3 All Pages Internal Oscillator Calibration 139 OSCICN 0xB2 All Pages Internal Oscillator Control 140 OSCLCN 0x86 All Pages Internal Low-Frequency Oscillator Control 142 OSCXCN 0xB1 All Pages External Oscillator Control 146 P0 0x80 All Pages Port 0 Latch 156 P0MDIN 0xF1 All Pages Port 0 Input Mode Configuration 156 P0MDOUT 0xA4 All Pages Port 0 Output Mode Configuration 157 P0SKIP 0xD4 All Pages Port 0 Skip 157 P1 0x90 All Pages Port 1 Latch 158 P1MDIN 0xF2 All Pages Port 1 Input Mode Configuration 158 P1MDOUT 0xA5 All Pages Port 1 Output Mode Configuration 159 P1SKIP 0xD5 All Pages Port 1 Skip 159 P2 0xA0 All Pages Port 2 Latch 160 P2MDIN 0xF3 All Pages Port 2 Input Mode Configuration 160 P2MDOUT 0xA6 All Pages Port 2 Output Mode Configuration 161 P2SKIP 0xD6 All Pages Port 2 Skip 161 P3 0xB0 All Pages Port 3 Latch 162 P3MDIN 0xF4 All Pages Port 3 Input Mode Configuration 162 P3MDOUT 0xA7 All Pages Port 3 Output Mode Configuration 163 P3SKIP 0xDF All Pages Port 3Skip 163 P4 0xC7 All Pages Port 4 Latch 164 P4MDIN 0xF5 All Pages Port 4 Input Mode Configuration 164 P4MDOUT 0xAE All Pages Port 4 Output Mode Configuration 165 PCA0CN 0xD8 All Pages PCA Control 272 PCA0CPH0 0xFC All Pages PCA Capture 0 High 276 PCA0CPH1 0xEA All Pages PCA Capture 1 High 276 PCA0CPH2 0xEC All Pages PCA Capture 2 High 276 PCA0CPH3 0xEE All Pages PCA Capture 3High 276 PCA0CPH4 0xFE All Pages PCA Capture 4 High 276 PCA0CPL0 0xFB All Pages PCA Capture 0 Low 276 PCA0CPL1 0xE9 All Pages PCA Capture 1 Low 276 108 0 INT0/INT1 Configuration Rev. 1.2 122 C8051F388/9/A/B Table 15.2. Special Function Registers (Continued) SFRs are listed in alphabetical order. All undefined SFR locations are reserved Register Address Page Description Page PCA0CPL2 0xEB All Pages PCA Capture 2 Low 276 PCA0CPL3 0xED All Pages PCA Capture 3 Low 276 PCA0CPL4 0xFD All Pages PCA Capture 4 Low 276 PCA0CPM0 0xDA All Pages PCA Module 0 Mode Register 274 PCA0CPM1 0xDB All Pages PCA Module 1 Mode Register 274 PCA0CPM2 0xDC All Pages PCA Module 2 Mode Register 274 PCA0CPM3 0xDD All Pages PCA Module 3 Mode Register 274 PCA0CPM4 0xDE All Pages PCA Module 4 Mode Register 274 PCA0H 0xFA All Pages PCA Counter High 275 PCA0L 0xF9 All Pages PCA Counter Low 275 PCA0MD 0xD9 All Pages PCA Mode 273 PCON 0x87 All Pages Power Control 74 PFE0CN 0xAF All Pages Prefetch Engine Control 84 PSCTL 0x8F All Pages Program Store R/W Control 133 PSW 0xD0 All Pages Program Status Word 83 REF0CN 0xD1 All Pages Voltage Reference Control 59 REG01CN 0xC9 All Pages Voltage Regulator 0 and 1 Control 71 RSTSRC 0xEF All Pages Reset Source Configuration/Status 128 SBCON1 0xAC All Pages UART1 Baud Rate Generator Control 209 SBRLH1 0xB5 All Pages UART1 Baud Rate Generator High 209 SBRLL1 0xB4 All Pages UART1 Baud Rate Generator Low 210 SBUF0 0x99 All Pages UART0 Data Buffer 199 SBUF1 0xD3 All Pages UART1 Data Buffer 208 SCON0 0x98 All Pages UART0 Control 198 SCON1 0xD2 All Pages UART1 Control 206 SFRPAGE 0xBF All Pages SFR Page Select 105 SMB0ADM 0xCE 0 SMBus0 Address Mask 180 SMB0ADR 0xCF 0 SMBus0 Address 179 SMB0CF 0xC1 0 SMBus0 Configuration 172 SMB0CN 0xC0 0 SMBus0 Control 176 SMB0DAT 0xC2 0 SMBus0 Data 182 SMB1ADM 0xCE F SMBus1 Address Mask 181 SMB1ADR 0xCF F SMBus1 Address 180 SMB1CF 0xC1 F SMBus1 Configuration 172 Rev. 1.2 109 C8051F388/9/A/B Table 15.2. Special Function Registers (Continued) SFRs are listed in alphabetical order. All undefined SFR locations are reserved Register Address Page Description Page SMB1CN 0xC0 F SMBus1 Control 177 SMB1DAT 0xC2 F SMBus1 Data 183 SMBTC 0xB9 F SMBus0/1 Timing Control 174 SMOD1 0xE5 All Pages UART1 Mode 207 SP 0x81 All Pages Stack Pointer 82 SPI0CFG 0xA1 All Pages SPI Configuration 218 SPI0CKR 0xA2 All Pages SPI Clock Rate Control 220 SPI0CN 0xF8 All Pages SPI Control 219 SPI0DAT 0xA3 All Pages SPI Data 220 TCON 0x88 All Pages Timer/Counter Control 231 TH0 0x8C All Pages Timer/Counter 0 High 234 TH1 0x8D All Pages Timer/Counter 1 High 234 TL0 0x8A All Pages Timer/Counter 0 Low 233 TL1 0x8B All Pages Timer/Counter 1 Low 233 TMOD 0x89 All Pages Timer/Counter Mode 232 TMR2CN 0xC8 0 Timer/Counter 2 Control 239 TMR2H 0xCD 0 Timer/Counter 2 High 241 TMR2L 0xCC 0 Timer/Counter 2 Low 240 TMR2RLH 0xCB 0 Timer/Counter 2 Reload High 240 TMR2RLL 0xCA 0 Timer/Counter 2 Reload Low 240 TMR3CN 0x91 0 Timer/Counter 3 Control 246 TMR3H 0x95 0 Timer/Counter 3 High 248 TMR3L 0x94 0 Timer/Counter 3 Low 247 TMR3RLH 0x93 0 Timer/Counter 3 Reload High 247 TMR3RLL 0x92 0 Timer/Counter 3 Reload Low 247 TMR4CN 0x91 F Timer/Counter 4 Control 251 TMR4H 0x95 F Timer/Counter 4 High 253 TMR4L 0x94 F Timer/Counter 4 Low 252 TMR4RLH 0x93 F Timer/Counter 4 Reload High 252 TMR4RLL 0x92 F Timer/Counter 4 Reload Low 252 TMR5CN 0xC8 F Timer/Counter 5 Control 256 TMR5H 0xCD F Timer/Counter 5 High 258 TMR5L 0xCC F Timer/Counter 5 Low 257 TMR5RLH 0xCB F Timer/Counter 5 Reload High 257 110 Rev. 1.2 C8051F388/9/A/B Table 15.2. Special Function Registers (Continued) SFRs are listed in alphabetical order. All undefined SFR locations are reserved Register Address Page Description F Timer/Counter 5 Reload Low Page TMR5RLL 0xCA VDM0CN 0xFF All Pages VDD Monitor Control 126 XBR0 0xE1 All Pages Port I/O Crossbar Control 0 153 XBR1 0xE2 All Pages Port I/O Crossbar Control 1 154 XBR2 0xE3 All Pages Port I/O Crossbar Control 2 155 Rev. 1.2 257 111 C8051F388/9/A/B 16. Interrupts The C8051F388/9/A/B include an extended interrupt system supporting multiple interrupt sources with two priority levels. The allocation of interrupt sources between on-chip peripherals and external inputs pins varies according to the specific version of the device. Each interrupt source has one or more associated interrupt-pending flag(s) located in an SFR. When a peripheral or external source meets a valid interrupt condition, the associated interrupt-pending flag is set to logic 1. If interrupts are enabled for the source, an interrupt request is generated when the interrupt-pending flag is set. As soon as execution of the current instruction is complete, the CPU generates an LCALL to a predetermined address to begin execution of an interrupt service routine (ISR). Each ISR must end with an RETI instruction, which returns program execution to the next instruction that would have been executed if the interrupt request had not occurred. If interrupts are not enabled, the interrupt-pending flag is ignored by the hardware and program execution continues as normal. (The interrupt-pending flag is set to logic 1 regardless of the interrupt's enable/disable state.) Each interrupt source can be individually enabled or disabled through the use of an associated interrupt enable bit in an SFR (IE, EIE1, or EIE2). However, interrupts must first be globally enabled by setting the EA bit (IE.7) to logic 1 before the individual interrupt enables are recognized. Setting the EA bit to logic 0 disables all interrupt sources regardless of the individual interrupt-enable settings. Note: Any instruction that clears a bit to disable an interrupt should be immediately followed by an instruction that has two or more opcode bytes. Using EA (global interrupt enable) as an example: // in 'C': EA = 0; // clear EA bit. EA = 0; // this is a dummy instruction with two-byte opcode. ; in assembly: CLR EA ; clear EA bit. CLR EA ; this is a dummy instruction with two-byte opcode. For example, if an interrupt is posted during the execution phase of a "CLR EA" opcode (or any instruction which clears a bit to disable an interrupt source), and the instruction is followed by a single-cycle instruction, the interrupt may be taken. However, a read of the enable bit will return a 0 inside the interrupt service routine. When the bit-clearing opcode is followed by a multi-cycle instruction, the interrupt will not be taken. Some interrupt-pending flags are automatically cleared by the hardware when the CPU vectors to the ISR. However, most are not cleared by the hardware and must be cleared by software before returning from the ISR. If an interrupt-pending flag remains set after the CPU completes the return-from-interrupt (RETI) instruction, a new interrupt request will be generated immediately and the CPU will re-enter the ISR after the completion of the next instruction. 112 Rev. 1.2 C8051F388/9/A/B 16.1. MCU Interrupt Sources and Vectors The C8051F388/9/A/B MCUs support several interrupt sources. Software can simulate an interrupt by setting any interrupt-pending flag to logic 1. If interrupts are enabled for the flag, an interrupt request will be generated and the CPU will vector to the ISR address associated with the interrupt-pending flag. MCU interrupt sources, associated vector addresses, priority order and control bits are summarized in Table 16.1. Refer to the datasheet section associated with a particular on-chip peripheral for information regarding valid interrupt conditions for the peripheral and the behavior of its interrupt-pending flag(s). 16.1.1. Interrupt Priorities Each interrupt source can be individually programmed to one of two priority levels: low or high. A low priority interrupt service routine can be preempted by a high priority interrupt. A high priority interrupt cannot be preempted. Each interrupt has an associated interrupt priority bit in an SFR (IP, EIP1, or EIP2) used to configure its priority level. Low priority is the default. If two interrupts are recognized simultaneously, the interrupt with the higher priority is serviced first. If both interrupts have the same priority level, a fixed priority order is used to arbitrate, given in Table 16.1. 16.1.2. Interrupt Latency Interrupt response time depends on the state of the CPU when the interrupt occurs. Pending interrupts are sampled and priority decoded each system clock cycle. Therefore, the fastest possible response time is 6 system clock cycles: 1 clock cycle to detect the interrupt and 5 clock cycles to complete the LCALL to the ISR. If an interrupt is pending when a RETI is executed, a single instruction is executed before an LCALL is made to service the pending interrupt. Therefore, the maximum response time for an interrupt (when no other interrupt is currently being serviced or the new interrupt is of greater priority) occurs when the CPU is performing an RETI instruction followed by a DIV as the next instruction. In this case, the response time is 20 system clock cycles: 1 clock cycle to detect the interrupt, 6 clock cycles to execute the RETI, 8 clock cycles to complete the DIV instruction and 5 clock cycles to execute the LCALL to the ISR. If the CPU is executing an ISR for an interrupt with equal or higher priority, the new interrupt will not be serviced until the current ISR completes, including the RETI and following instruction. Note that the CPU is stalled during Flash write operations. Interrupt service latency will be increased for interrupts occurring while the CPU is stalled. The latency for these situations will be determined by the standard interrupt service procedure (as described above) and the amount of time the CPU is stalled. 16.2. Interrupt Register Descriptions The SFRs used to enable the interrupt sources and set their priority level are described in this section. Refer to the data sheet section associated with a particular on-chip peripheral for information regarding valid interrupt conditions for the peripheral and the behavior of its interrupt-pending flag(s). Rev. 1.2 113 C8051F388/9/A/B Interrupt Source Interrupt Vector Priority Order Reset 0x0000 Top External Interrupt 0 (INT0) Timer 0 Overflow External Interrupt 1 (INT1) Timer 1 Overflow UART0 0x0003 0 0x000B 0x0013 Pending Flag Enable Flag Priority Control N/A N/A IE0 (TCON.1) Y Y Always Always Enabled Highest EX0 (IE.0) PX0 (IP.0) 1 2 TF0 (TCON.5) IE1 (TCON.3) Y Y Y Y ET0 (IE.1) PT0 (IP.1) EX1 (IE.2) PX1 (IP.2) 0x001B 0x0023 3 4 Y Y Y N ET1 (IE.3) PT1 (IP.3) ES0 (IE.4) PS0 (IP.4) Timer 2 Overflow 0x002B 5 Y N ET2 (IE.5) PT2 (IP.5) SPI0 0x0033 6 Y N ESPI0 (IE.6) PSPI0 (IP.6) SMB0 0x003B 7 TF1 (TCON.7) RI0 (SCON0.0) TI0 (SCON0.1) TF2H (TMR2CN.7) TF2L (TMR2CN.6) SPIF (SPI0CN.7) WCOL (SPI0CN.6) MODF (SPI0CN.5) RXOVRN (SPI0CN.4) SI (SMB0CN.0) Y N Reserved ADC0 Window Compare ADC0 Conversion Complete Programmable Counter Array Comparator0 0x0043 0x004B 8 9 N/A Y N/A N 0x0053 10 N/A AD0WINT (ADC0CN.3) AD0INT (ADC0CN.5) Y N 0x005B 11 Y N 0x0063 12 N N Comparator1 0x006B 13 N N Timer 3 Overflow 0x0073 14 N N INT2 Level 0x007B 15 CF (PCA0CN.7) CCFn (PCA0CN.n) CP0FIF (CPT0CN.4) CP0RIF (CPT0CN.5) CP1FIF (CPT1CN.4) CP1RIF (CPT1CN.5) TF3H (TMR3CN.7) TF3L (TMR3CN.6) N/A N/A N/A UART1 0x0083 16 N N Reserved SMB1 0x008B 0x0093 17 18 N/A Y N/A N Timer 4 Overflow 0x009B 19 N N Timer 5 Overflow 0x00A3 20 Y N ESMB0 (EIE1.0) N/A EWADC0 (EIE1.2) EADC0 (EIE1.3) EPCA0 (EIE1.4) ECP0 (EIE1.5) ECP1 (EIE1.6) ET3 (EIE1.7) EINT2 (EIE2.0) ES1 (EIE2.1) N/A ESMB1 (EIE2.3) ET4 (EIE2.4) ET5 (EIE2.5) PSMB0 (EIP1.0) N/A PWADC0 (EIP1.2) PADC0 (EIP1.3) PPCA0 (EIP1.4) PCP0 (EIP1.5) PCP1 (EIP1.6) PT3 (EIP1.7) PINT2 (EIP2.0) PS1 (EIP2.1) N/A PSMB1 (EIP2.3) PT4 (E!P2.4) PT5 (E!P2.5) 114 None Bit Address? Cleared by HW? Table 16.1. Interrupt Summary RI1 (SCON1.0) TI1 (SCON1.1) N/A SI (SMB1CN.0) TF4H (TMR4CN.7) TF4L (TMR4CN.6) TF5H (TMR5CN.7) TF5L (TMR5CN.6) Rev. 1.2 C8051F388/9/A/B SFR Definition 16.1. IE: Interrupt Enable Bit 7 6 5 4 3 2 1 0 Name EA ESPI0 ET2 ES0 ET1 EX1 ET0 EX0 Type R/W R/W R/W R/W R/W R/W R/W R/W Reset 0 0 0 0 0 0 0 0 SFR Address = 0xA8; SFR Page = All Pages; Bit-Addressable Bit Name Function 7 EA Enable All Interrupts. Globally enables/disables all interrupts. It overrides individual interrupt mask settings. 0: Disable all interrupt sources. 1: Enable each interrupt according to its individual mask setting. 6 ESPI0 5 ET2 Enable Timer 2 Interrupt. This bit sets the masking of the Timer 2 interrupt. 0: Disable Timer 2 interrupt. 1: Enable interrupt requests generated by the TF2L or TF2H flags. 4 ES0 Enable UART0 Interrupt. This bit sets the masking of the UART0 interrupt. 0: Disable UART0 interrupt. 1: Enable UART0 interrupt. 3 ET1 Enable Timer 1 Interrupt. This bit sets the masking of the Timer 1 interrupt. 0: Disable all Timer 1 interrupt. 1: Enable interrupt requests generated by the TF1 flag. 2 EX1 Enable External Interrupt 1. This bit sets the masking of External Interrupt 1. 0: Disable external interrupt 1. 1: Enable interrupt requests generated by the INT1 input. 1 ET0 Enable Timer 0 Interrupt. This bit sets the masking of the Timer 0 interrupt. 0: Disable all Timer 0 interrupt. 1: Enable interrupt requests generated by the TF0 flag. 0 EX0 Enable External Interrupt 0. This bit sets the masking of External Interrupt 0. 0: Disable external interrupt 0. 1: Enable interrupt requests generated by the INT0 input. Enable Serial Peripheral Interface (SPI0) Interrupt. This bit sets the masking of the SPI0 interrupts. 0: Disable all SPI0 interrupts. 1: Enable interrupt requests generated by SPI0. Rev. 1.2 115 C8051F388/9/A/B SFR Definition 16.2. IP: Interrupt Priority Bit 7 Name 6 5 4 3 2 1 0 PSPI0 PT2 PS0 PT1 PX1 PT0 PX0 Type R R/W R/W R/W R/W R/W R/W R/W Reset 1 0 0 0 0 0 0 0 SFR Address = 0xB8; SFR Page = All Pages; Bit-Addressable Bit Name Function 7 Unused 6 PSPI0 5 PT2 Timer 2 Interrupt Priority Control. This bit sets the priority of the Timer 2 interrupt. 0: Timer 2 interrupt set to low priority level. 1: Timer 2 interrupt set to high priority level. 4 PS0 UART0 Interrupt Priority Control. This bit sets the priority of the UART0 interrupt. 0: UART0 interrupt set to low priority level. 1: UART0 interrupt set to high priority level. 3 PT1 Timer 1 Interrupt Priority Control. This bit sets the priority of the Timer 1 interrupt. 0: Timer 1 interrupt set to low priority level. 1: Timer 1 interrupt set to high priority level. 2 PX1 External Interrupt 1 Priority Control. This bit sets the priority of the External Interrupt 1 interrupt. 0: External Interrupt 1 set to low priority level. 1: External Interrupt 1 set to high priority level. 1 PT0 Timer 0 Interrupt Priority Control. This bit sets the priority of the Timer 0 interrupt. 0: Timer 0 interrupt set to low priority level. 1: Timer 0 interrupt set to high priority level. 0 PX0 External Interrupt 0 Priority Control. This bit sets the priority of the External Interrupt 0 interrupt. 0: External Interrupt 0 set to low priority level. 1: External Interrupt 0 set to high priority level. 116 Read = 1b, Write = Don't Care. Serial Peripheral Interface (SPI0) Interrupt Priority Control. This bit sets the priority of the SPI0 interrupt. 0: SPI0 interrupt set to low priority level. 1: SPI0 interrupt set to high priority level. Rev. 1.2 C8051F388/9/A/B SFR Definition 16.3. EIE1: Extended Interrupt Enable 1 Bit 7 6 5 4 3 2 1 0 Name ET3 ECP1 ECP0 EPCA0 EADC0 EWADC0 Reserved ESMB0 Type R/W R/W R/W R/W R/W R/W R/W R/W Reset 0 0 0 0 0 0 0 0 SFR Address = 0xE6; SFR Page = All Pages Bit Name Function 7 ET3 Enable Timer 3 Interrupt. This bit sets the masking of the Timer 3 interrupt. 0: Disable Timer 3 interrupts. 1: Enable interrupt requests generated by the TF3L or TF3H flags. 6 ECP1 Enable Comparator1 (CP1) Interrupt. This bit sets the masking of the CP1 interrupt. 0: Disable CP1 interrupts. 1: Enable interrupt requests generated by the CP1RIF or CP1FIF flags. 5 ECP0 Enable Comparator0 (CP0) Interrupt. This bit sets the masking of the CP0 interrupt. 0: Disable CP0 interrupts. 1: Enable interrupt requests generated by the CP0RIF or CP0FIF flags. 4 EPCA0 Enable Programmable Counter Array (PCA0) Interrupt. This bit sets the masking of the PCA0 interrupts. 0: Disable all PCA0 interrupts. 1: Enable interrupt requests generated by PCA0. 3 EADC0 Enable ADC0 Conversion Complete Interrupt. This bit sets the masking of the ADC0 Conversion Complete interrupt. 0: Disable ADC0 Conversion Complete interrupt. 1: Enable interrupt requests generated by the AD0INT flag. 2 EWADC0 Enable Window Comparison ADC0 Interrupt. This bit sets the masking of ADC0 Window Comparison interrupt. 0: Disable ADC0 Window Comparison interrupt. 1: Enable interrupt requests generated by ADC0 Window Compare flag (AD0WINT). 1 Reserved Read = 0b, Must Write 0b. 0 ESMB0 Enable SMBus0 Interrupt. This bit sets the masking of the SMB0 interrupt. 0: Disable all SMB0 interrupts. 1: Enable interrupt requests generated by SMB0. Rev. 1.2 117 C8051F388/9/A/B SFR Definition 16.4. EIP1: Extended Interrupt Priority 1 Bit 7 6 5 4 3 2 1 0 Name PT3 PCP1 PCP0 PPCA0 PADC0 PWADC0 Reserved PSMB0 Type R/W R/W R/W R/W R/W R/W R/W R/W Reset 0 0 0 0 0 0 0 0 SFR Address = 0xF6; SFR Page = All Pages Bit Name Function 7 PT3 Timer 3 Interrupt Priority Control. This bit sets the priority of the Timer 3 interrupt. 0: Timer 3 interrupts set to low priority level. 1: Timer 3 interrupts set to high priority level. 6 PCP1 Comparator1 (CP1) Interrupt Priority Control. This bit sets the priority of the CP1 interrupt. 0: CP1 interrupt set to low priority level. 1: CP1 interrupt set to high priority level. 5 PCP0 Comparator0 (CP0) Interrupt Priority Control. This bit sets the priority of the CP0 interrupt. 0: CP0 interrupt set to low priority level. 1: CP0 interrupt set to high priority level. 4 PPCA0 Programmable Counter Array (PCA0) Interrupt Priority Control. This bit sets the priority of the PCA0 interrupt. 0: PCA0 interrupt set to low priority level. 1: PCA0 interrupt set to high priority level. 3 PADC0 ADC0 Conversion Complete Interrupt Priority Control. This bit sets the priority of the ADC0 Conversion Complete interrupt. 0: ADC0 Conversion Complete interrupt set to low priority level. 1: ADC0 Conversion Complete interrupt set to high priority level. 2 PWADC0 ADC0 Window Comparator Interrupt Priority Control. This bit sets the priority of the ADC0 Window interrupt. 0: ADC0 Window interrupt set to low priority level. 1: ADC0 Window interrupt set to high priority level. 1 Reserved Read = 0b, Must Write 0b. 0 118 PSMB0 SMBus0 Interrupt Priority Control. This bit sets the priority of the SMB0 interrupt. 0: SMB0 interrupt set to low priority level. 1: SMB0 interrupt set to high priority level. Rev. 1.2 C8051F388/9/A/B SFR Definition 16.5. EIE2: Extended Interrupt Enable 2 Bit 7 6 Name 5 4 3 ET5 ET4 ESMB1 2 1 0 ES1 EINT2 Type R R R/W R/W R/W R/W R/W R/W Reset 0 0 0 0 0 0 0 0 SFR Address = 0xE7; SFR Page = All Pages Bit Name Function 7:6 Unused 5 ET5 Enable Timer 5 Interrupt. This bit sets the masking of the Timer 5 interrupt. 0: Disable Timer 5 interrupts. 1: Enable interrupt requests generated by the TF5L or TF5H flags. 4 ET4 Enable Timer 4 Interrupt. This bit sets the masking of the Timer 4 interrupt. 0: Disable Timer 4interrupts. 1: Enable interrupt requests generated by the TF4L or TF4H flags. 3 ESMB1 2 Read = 00b, Write = Don't Care. Enable SMBus1 Interrupt. This bit sets the masking of the SMB1 interrupt. 0: Disable all SMB1 interrupts. 1: Enable interrupt requests generated by SMB1. Reserved Must Write 0b. 1 ES1 0 EINT2 Enable UART1 Interrupt. This bit sets the masking of the UART1 interrupt. 0: Disable UART1 interrupt. 1: Enable UART1 interrupt. Enable INT2 Level Interrupt. This bit sets the masking of the INT2 interrupt. 0: Disable all INT2 interrupts. 1: Enable interrupt requests generated by the INT2 level sense. Rev. 1.2 119 C8051F388/9/A/B SFR Definition 16.6. EIP2: Extended Interrupt Priority 2 Bit 7 6 Name 5 4 3 PT5 PT4 PSMB1 2 1 0 PS1 PINT2 Type R R R/W R/W R/W R/W R/W R/W Reset 0 0 0 0 0 0 0 0 SFR Address = 0xF7; SFR Page = All Pages Bit Name Function :6 Unused 5 PT5 Timer 5 Interrupt Priority Control. This bit sets the priority of the Timer 5 interrupt. 0: Timer 5 interrupt set to low priority level. 1: Timer 5 interrupt set to high priority level. 4 PT4 Timer 4 Interrupt Priority Control. This bit sets the priority of the Timer 4 interrupt. 0: Timer 4 interrupt set to low priority level. 1: Timer 4 interrupt set to high priority level. 3 PSMB1 2 Read = 00b, Write = Don't Care. SMBus1 Interrupt Priority Control. This bit sets the priority of the SMB1 interrupt. 0: SMB1 interrupt set to low priority level. 1: SMB1 interrupt set to high priority level. Reserved Must Write 0b. 1 PS1 UART1 Interrupt Priority Control. This bit sets the priority of the UART1 interrupt. 0: UART1 interrupt set to low priority level. 1: UART1 interrupt set to high priority level. 0 PINT2 INT2 Level Interrupt Priority Control. This bit sets the masking of the INT2 interrupt. 0: INT2 interrupt set to low priority level. 1: INT2 interrupt set to high priority level. 120 Rev. 1.2 C8051F388/9/A/B 16.3. INT0 and INT1 External Interrupt Sources The INT0 and INT1 external interrupt sources are configurable as active high or low, edge or level sensitive. The IN0PL (INT0 Polarity) and IN1PL (INT1 Polarity) bits in the IT01CF register select active high or active low; the IT0 and IT1 bits in TCON (Section “25.1. Timer 0 and Timer 1” on page 227) select level or edge sensitive. The table below lists the possible configurations. IT1 IN1PL Active low, edge sensitive 1 0 Active low, edge sensitive 1 Active high, edge sensitive 1 1 Active high, edge sensitive 0 0 Active low, level sensitive 0 0 Active low, level sensitive 0 1 Active high, level sensitive 0 1 Active high, level sensitive IT0 IN0PL 1 0 1 INT0 Interrupt INT1 Interrupt INT0 and INT1 are assigned to Port pins as defined in the IT01CF register (see SFR Definition 16.7). Note that INT0 and INT0 Port pin assignments are independent of any Crossbar assignments. INT0 and INT1 will monitor their assigned Port pins without disturbing the peripheral that was assigned the Port pin via the Crossbar. To assign a Port pin only to INT0 and/or INT1, configure the Crossbar to skip the selected pin(s). This is accomplished by setting the associated bit in register PnSKIP (see Section “20.1. Priority Crossbar Decoder” on page 148 for complete details on configuring the Crossbar). IE0 (TCON.1) and IE1 (TCON.3) serve as the interrupt-pending flags for the INT0 and INT1 external interrupts, respectively. If an INT0 or INT1 external interrupt is configured as edge-sensitive, the corresponding interrupt-pending flag is automatically cleared by the hardware when the CPU vectors to the ISR. When configured as level sensitive, the interrupt-pending flag remains logic 1 while the input is active as defined by the corresponding polarity bit (IN0PL or IN1PL); the flag remains logic 0 while the input is inactive. The external interrupt source must hold the input active until the interrupt request is recognized. It must then deactivate the interrupt request before execution of the ISR completes or another interrupt request will be generated. Rev. 1.2 121 C8051F388/9/A/B SFR Definition 16.7. IT01CF: INT0/INT1 ConfigurationO Bit 7 6 5 Name IN1PL IN1SL[2:0] IN0PL IN0SL[2:0] Type R/W R/W R/W R/W Reset 0 0 0 4 0 SFR Address = 0xE4; SFR Page = 0 Bit Name 7 6:4 3 2:0 122 IN1PL 3 0 2 0 1 0 0 1 Function INT1 Polarity. 0: INT1 input is active low. 1: INT1 input is active high. IN1SL[2:0] INT1 Port Pin Selection Bits. These bits select which Port pin is assigned to INT1. Note that this pin assignment is independent of the Crossbar; INT1 will monitor the assigned Port pin without disturbing the peripheral that has been assigned the Port pin via the Crossbar. The Crossbar will not assign the Port pin to a peripheral if it is configured to skip the selected pin. 000: Select P0.0 001: Select P0.1 010: Select P0.2 011: Select P0.3 100: Select P0.4 101: Select P0.5 110: Select P0.6 111: Select P0.7 IN0PL INT0 Polarity. 0: INT0 input is active low. 1: INT0 input is active high. IN0SL[2:0] INT0 Port Pin Selection Bits. These bits select which Port pin is assigned to INT0. Note that this pin assignment is independent of the Crossbar; INT0 will monitor the assigned Port pin without disturbing the peripheral that has been assigned the Port pin via the Crossbar. The Crossbar will not assign the Port pin to a peripheral if it is configured to skip the selected pin. 000: Select P0.0 001: Select P0.1 010: Select P0.2 011: Select P0.3 100: Select P0.4 101: Select P0.5 110: Select P0.6 111: Select P0.7 Rev. 1.2 C8051F388/9/A/B 17. Reset Sources Reset circuitry allows the controller to be easily placed in a predefined default condition. On entry to this reset state, the following occur:     CIP-51 halts program execution Special Function Registers (SFRs) are initialized to their defined reset values External Port pins are forced to a known state Interrupts and timers are disabled. All SFRs are reset to the predefined values noted in the SFR detailed descriptions. The contents of internal data memory are unaffected during a reset; any previously stored data is preserved. However, since the stack pointer SFR is reset, the stack is effectively lost, even though the data on the stack is not altered. The Port I/O latches are reset to 0xFF (all logic ones) in open-drain mode. Weak pullups are enabled during and after the reset. For VDD Monitor and power-on resets, the RST pin is driven low until the device exits the reset state. On exit from the reset state, the program counter (PC) is reset, and the system clock defaults to the internal oscillator. The Watchdog Timer is enabled with the system clock divided by 12 as its clock source. Program execution begins at location 0x0000. Figure 17.1. Reset Sources Rev. 1.2 123 C8051F388/9/A/B 17.1. Power-On Reset During power-up, the device is held in a reset state and the RST pin is driven low until VDD settles above VRST. A delay occurs before the device is released from reset; the delay decreases as the VDD ramp time increases (VDD ramp time is defined as how fast VDD ramps from 0 V to VRST). Figure 17.2. plots the power-on and VDD monitor event timing. The maximum VDD ramp time is 1 ms; slower ramp times may cause the device to be released from reset before VDD reaches the VRST level. For ramp times less than 1 ms, the power-on reset delay (TPORDelay) is typically less than 0.3 ms. On exit from a power-on or VDD monitor reset, the PORSF flag (RSTSRC.1) is set by hardware to logic 1. When PORSF is set, all of the other reset flags in the RSTSRC Register are indeterminate (PORSF is cleared by all other resets). Since all resets cause program execution to begin at the same location (0x0000) software can read the PORSF flag to determine if a power-up was the cause of reset. The content of internal data memory should be assumed to be undefined after a power-on reset. The VDD monitor is enabled following a power-on reset. Figure 17.2. Power-On and VDD Monitor Reset Timing 124 Rev. 1.2 C8051F388/9/A/B 17.2. Power-Fail Reset / VDD Monitor When a powerdown transition or power irregularity causes VDD to drop below VRST, the power supply monitor will drive the RST pin low and hold the CIP-51 in a reset state (see Figure 17.2). When VDD returns to a level above VRST, the CIP-51 will be released from the reset state. Note that even though internal data memory contents are not altered by the power-fail reset, it is impossible to determine if VDD dropped below the level required for data retention. If the PORSF flag reads 1, the data may no longer be valid. The VDD monitor is enabled after power-on resets. Its defined state (enabled/disabled) is not altered by any other reset source. For example, if the VDD monitor is disabled by code and a software reset is performed, the VDD monitor will still be disabled after the reset. Important Note: If the VDD monitor is being turned on from a disabled state, it should be enabled before it is selected as a reset source. Selecting the VDD monitor as a reset source before it is enabled and stabilized may cause a system reset. In some applications, this reset may be undesirable. If this is not desirable in the application, a delay should be introduced between enabling the monitor and selecting it as a reset source. The procedure for enabling the VDD monitor and configuring it as a reset source from a disabled state is shown below: 1. Enable the VDD monitor (VDMEN bit in VDM0CN = 1). 2. If necessary, wait for the VDD monitor to stabilize (see Table 5.4 for the VDD Monitor turn-on time). 3. Select the VDD monitor as a reset source (PORSF bit in RSTSRC = 1). See Figure 17.2 for VDD monitor timing; note that the power-on-reset delay is not incurred after a VDD monitor reset. See Table 5.4 for complete electrical characteristics of the VDD monitor. Rev. 1.2 125 C8051F388/9/A/B SFR Definition 17.1. VDM0CN: VDD Monitor Control Bit 7 6 5 4 3 2 1 0 Name VDMEN VDDSTAT Type R/W R R R R R R R Reset Varies Varies Varies Varies Varies Varies Varies Varies SFR Address = 0xFF; SFR Page = All Pages Bit Name 7 VDMEN Function VDD Monitor Enable. This bit turns the VDD monitor circuit on/off. The VDD Monitor cannot generate system resets until it is also selected as a reset source in register RSTSRC (SFR Definition 17.2). Selecting the VDD monitor as a reset source before it has stabilized may generate a system reset. In systems where this reset would be undesirable, a delay should be introduced between enabling the VDD Monitor and selecting it as a reset source. See Table 5.4 for the minimum VDD Monitor turn-on time. 0: VDD Monitor Disabled. 1: VDD Monitor Enabled. 6 VDDSTAT VDD Status. This bit indicates the current power supply status (VDD Monitor output). 0: VDD is at or below the VDD monitor threshold. 1: VDD is above the VDD monitor threshold. 5:0 Unused Read = 000000b; Write = Don’t care. 17.3. External Reset The external RST pin provides a means for external circuitry to force the device into a reset state. Asserting an active-low signal on the RST pin generates a reset; an external pullup and/or decoupling of the RST pin may be necessary to avoid erroneous noise-induced resets. See Table 5.4 for complete RST pin specifications. The PINRSF flag (RSTSRC.0) is set on exit from an external reset. 17.4. Missing Clock Detector Reset The Missing Clock Detector (MCD) is a one-shot circuit that is triggered by the system clock. If the system clock remains high or low for more than the MCD time-out, a reset will be generated. After a MCD reset, the MCDRSF flag (RSTSRC.2) will read 1, signifying the MCD as the reset source; otherwise, this bit reads 0. Writing a 1 to the MCDRSF bit enables the Missing Clock Detector; writing a 0 disables it. The state of the RST pin is unaffected by this reset. 17.5. Comparator0 Reset Comparator0 can be configured as a reset source by writing a 1 to the C0RSEF flag (RSTSRC.5). Comparator0 should be enabled and allowed to settle prior to writing to C0RSEF to prevent any turn-on chatter on the output from generating an unwanted reset. The Comparator0 reset is active-low: if the non-inverting input voltage (on CP0+) is less than the inverting input voltage (on CP0-), the device is put into the reset state. After a Comparator0 reset, the C0RSEF flag (RSTSRC.5) will read 1 signifying Comparator0 as the reset source; otherwise, this bit reads 0. The state of the RST pin is unaffected by this reset. 126 Rev. 1.2 C8051F388/9/A/B 17.6. PCA Watchdog Timer Reset The programmable Watchdog Timer (WDT) function of the Programmable Counter Array (PCA) can be used to prevent software from running out of control during a system malfunction. The PCA WDT function can be enabled or disabled by software as described in Section “26.4. Watchdog Timer Mode” on page 269; the WDT is enabled and clocked by SYSCLK / 12 following any reset. If a system malfunction prevents user software from updating the WDT, a reset is generated and the WDTRSF bit (RSTSRC.5) is set to 1. The state of the RST pin is unaffected by this reset. 17.7. Flash Error Reset If a Flash program read, write, or erase operation targets an illegal address, a system reset is generated. This may occur due to any of the following:      Programming hardware attempts to write or erase a Flash location which is above the user code space address limit. A Flash read from firmware is attempted above user code space. This occurs when a MOVC operation is attempted above the user code space address limit. A Program read is attempted above user code space. This occurs when user code attempts to branch to an address above the user code space address limit. A Flash read, write, or erase attempt is restricted due to a Flash security setting. A Flash write or erase is attempted when the VDD monitor is not enabled. The FERROR bit (RSTSRC.6) is set following a Flash error reset. The state of the RST pin is unaffected by this reset. 17.8. Software Reset Software may force a reset by writing a 1 to the SWRSF bit (RSTSRC.4). The SWRSF bit will read 1 following a software forced reset. The state of the RST pin is unaffected by this reset. Rev. 1.2 127 C8051F388/9/A/B SFR Definition 17.2. RSTSRC: Reset Source Bit 7 Name Reserved 6 5 4 3 2 1 0 FERROR C0RSEF SWRSF WDTRSF MCDRSF PORSF PINRSF Type R/W R R/W R/W R R/W R/W R Reset Varies Varies Varies Varies Varies Varies Varies Varies SFR Address = 0xEF; SFR Page = All Pages Bit Name Description 7 Reserved Must Write 0b. Read = 0b 6 FERROR Flash Error Reset Flag. N/A Set to 1 if Flash read/write/erase error caused the last reset. 5 C0RSEF Comparator0 Reset Enable and Flag. Writing a 1 enables Com- Set to 1 if Comparator0 parator0 as a reset source caused the last reset. (active-low). 4 SWRSF Writing a 1 forces a system reset. Software Reset Force and Flag. Write 3 WDTRSF Watchdog Timer Reset Flag. N/A 2 MCDRSF Missing Clock Detector Enable and Flag. Read Set to 1 if last reset was caused by a write to SWRSF. Set to 1 if Watchdog Timer overflow caused the last reset. Writing a 1 enables the Set to 1 if Missing Clock Missing Clock Detector. Detector timeout caused The MCD triggers a reset the last reset. if a missing clock condition is detected. 1 PORSF Power-On / VDD Monitor Writing a 1 enables the Reset Flag, and VDD monitor VDD monitor as a reset source. Reset Enable. Writing 1 to this bit before the VDD monitor is enabled and stabilized may cause a system reset. Set to 1 anytime a poweron or VDD monitor reset occurs. When set to 1 all other RSTSRC flags are indeterminate. 0 PINRSF HW Pin Reset Flag. Set to 1 if RST pin caused the last reset. N/A Note: Do not use read-modify-write operations on this register 128 Rev. 1.2 C8051F388/9/A/B 18. Flash Memory On-chip, re-programmable Flash memory is included for program code and non-volatile data storage. The Flash memory can be programmed in-system through the C2 interface or by software using the MOVX instruction. Once cleared to logic 0, a Flash bit must be erased to set it back to logic 1. Flash bytes would typically be erased (set to 0xFF) before being reprogrammed. The write and erase operations are automatically timed by hardware for proper execution; data polling to determine the end of the write/erase operation is not required. Code execution is stalled during a Flash write/erase operation. 18.1. Programming The Flash Memory The simplest means of programming the Flash memory is through the C2 interface using programming tools provided by Silicon Labs or a third party vendor. This is the only means for programming a non-initialized device. For details on the C2 commands to program Flash memory, see Section “27. C2 Interface” on page 277. To ensure the integrity of Flash contents, it is strongly recommended that the VDD monitor be left enabled in any system which writes or erases Flash memory from code. It is also crucial to ensure that the FLRT bit in register FLSCL be set to '1' if a clock speed higher than 25 MHz is being used for the device. 18.1.1. Flash Lock and Key Functions Flash writes and erases by user software are protected with a lock and key function. The Flash Lock and Key Register (FLKEY) must be written with the correct key codes, in sequence, before Flash operations may be performed. The key codes are: 0xA5, 0xF1. The timing does not matter, but the codes must be written in order. If the key codes are written out of order, or the wrong codes are written, Flash writes and erases will be disabled until the next system reset. Flash writes and erases will also be disabled if a Flash write or erase is attempted before the key codes have been written properly. The Flash lock resets after each write or erase; the key codes must be written again before a following Flash operation can be performed. The FLKEY register is detailed in SFR Definition 18.2. 18.1.2. Flash Erase Procedure The Flash memory can be programmed by software using the MOVX write instruction with the address and data byte to be programmed provided as normal operands. Before writing to Flash memory using MOVX, Flash write operations must be enabled by: (1) Writing the Flash key codes in sequence to the Flash Lock register (FLKEY); and (2) Setting the PSWE Program Store Write Enable bit (PSCTL.0) to logic 1 (this directs the MOVX writes to target Flash memory). The PSWE bit remains set until cleared by software. A write to Flash memory can clear bits to logic 0 but cannot set them; only an erase operation can set bits to logic 1 in Flash. A byte location to be programmed must be erased before a new value is written. The Flash memory is organized in 512-byte pages. The erase operation applies to an entire page (setting all bytes in the page to 0xFF). To erase an entire 512-byte page, perform the following steps: 1. 2. 3. 4. 5. 6. 7. 8. Disable interrupts (recommended). Write the first key code to FLKEY: 0xA5. Write the second key code to FLKEY: 0xF1. Set the PSEE bit (register PSCTL). Set the PSWE bit (register PSCTL). Using the MOVX instruction, write a data byte to any location within the 512-byte page to be erased. Clear the PSWE bit (register PSCTL). Clear the PSEE bit (register PSCTI). Rev. 1.2 129 C8051F388/9/A/B 18.1.3. Flash Write Procedure Bytes in Flash memory can be written one byte at a time, or in groups of two. The FLBWE bit in register PFE0CN (SFR Definition ) controls whether a single byte or a block of two bytes is written to Flash during a write operation. When FLBWE is cleared to 0, the Flash will be written one byte at a time. When FLBWE is set to 1, the Flash will be written in two-byte blocks. Block writes are performed in the same amount of time as single-byte writes, which can save time when storing large amounts of data to Flash memory.During a single-byte write to Flash, bytes are written individually, and a Flash write will be performed after each MOVX write instruction. The recommended procedure for writing Flash in single bytes is: 1. Disable interrupts. 2. Clear the FLBWE bit (register PFE0CN) to select single-byte write mode. 3. Set the PSWE bit (register PSCTL). 4. Clear the PSEE bit (register PSCTL). 5. Write the first key code to FLKEY: 0xA5. 6. Write the second key code to FLKEY: 0xF1. 7. Using the MOVX instruction, write a single data byte to the desired location within the 512-byte sector. 8. Clear the PSWE bit. 9. Re-enable interrupts. Steps 5-7 must be repeated for each byte to be written. For block Flash writes, the Flash write procedure is only performed after the last byte of each block is written with the MOVX write instruction. A Flash write block is two bytes long, from even addresses to odd addresses. Writes must be performed sequentially (i.e. addresses ending in 0b and 1b must be written in order). The Flash write will be performed following the MOVX write that targets the address ending in 1b. If a byte in the block does not need to be updated in Flash, it should be written to 0xFF. The recommended procedure for writing Flash in blocks is: 1. Disable interrupts. 2. Set the FLBWE bit (register PFE0CN) to select block write mode. 3. Set the PSWE bit (register PSCTL). 4. Clear the PSEE bit (register PSCTL). 5. Write the first key code to FLKEY: 0xA5. 6. Write the second key code to FLKEY: 0xF1. 7. Using the MOVX instruction, write the first data byte to the even block location (ending in 0b). 8. Write the first key code to FLKEY: 0xA5. 9. Write the second key code to FLKEY: 0xF1. 10.Using the MOVX instruction, write the second data byte to the odd block location (ending in 1b). 11. Clear the PSWE bit. 12.Re-enable interrupts. Steps 5–10 must be repeated for each block to be written. 130 Rev. 1.2 C8051F388/9/A/B 18.2. Non-Volatile Data Storage The Flash memory can be used for non-volatile data storage as well as program code. This allows data such as calibration coefficients to be calculated and stored at run time. Data is written using the MOVX write instruction and read using the MOVC instruction. Note: MOVX read instructions always target XRAM. 18.3. Security Options The CIP-51 provides security options to protect the Flash memory from inadvertent modification by software as well as to prevent the viewing of proprietary program code and constants. The Program Store Write Enable (bit PSWE in register PSCTL) and the Program Store Erase Enable (bit PSEE in register PSCTL) bits protect the Flash memory from accidental modification by software. PSWE must be explicitly set to 1 before software can modify the Flash memory; both PSWE and PSEE must be set to 1 before software can erase Flash memory. Additional security features prevent proprietary program code and data constants from being read or altered across the C2 interface. A Security Lock Byte located at the last byte of Flash user space offers protection of the Flash program memory from access (reads, writes, or erases) by unprotected code or the C2 interface. The Flash security mechanism allows the user to lock n 512-byte Flash pages, starting at page 0 (addresses 0x0000 to 0x01FF), where n is the 1s complement number represented by the Security Lock Byte. Note that the page containing the Flash Security Lock Byte is also locked when any other Flash pages are locked. See example below. Security Lock Byte: 1s Complement: Flash pages locked: Addresses locked: 11111101b 00000010b 3 (2 + Flash Lock Byte Page) First two pages of Flash: 0x0000 to 0x03FF Flash Lock Byte Page: (0xFA00 to 0xFBFF for 64k devices; 0x7E00 to 0x7FFF for 32k devices) Figure 18.1. Flash Program Memory Map and Security Byte The level of FLASH security depends on the FLASH access method. The three FLASH access methods that can be restricted are reads, writes, and erases from the C2 debug interface, user firmware executing on unlocked pages, and user firmware executing on locked pages. Rev. 1.2 131 C8051F388/9/A/B Accessing FLASH from the C2 debug interface: 1. 2. 3. 4. 5. 6. 7. Any unlocked page may be read, written, or erased. Locked pages cannot be read, written, or erased. The page containing the Lock Byte may be read, written, or erased if it is unlocked. Reading the contents of the Lock Byte with no pages locked is always permitted. Reading the contents of the Lock Byte with any pages locked is not permitted. Locking additional pages (changing 1s to 0s in the Lock Byte) is not permitted. Unlocking FLASH pages (changing 0s to 1s in the Lock Byte) requires the C2 Device Erase command, which erases all FLASH pages including the page containing the Lock Byte and the Lock Byte itself. 8. The Reserved Area cannot be read, written, or erased. Accessing FLASH from user firmware executing on an unlocked page: 1. 2. 3. 4. 5. 6. 7. 8. Any unlocked page except the page containing the Lock Byte may be read, written, or erased. Locked pages cannot be read, written, or erased. The page containing the Lock Byte cannot be erased. It may be read or written only if it is unlocked. Reading the contents of the Lock Byte with no pages locked is always permitted. Reading the contents of the Lock Byte with any pages locked is not permitted. Locking additional pages (changing 1s to 0s in the Lock Byte) is not permitted. Unlocking FLASH pages (changing 0s to 1s in the Lock Byte) is not permitted. The Reserved Area cannot be read, written, or erased. Any attempt to access the reserved area, or any other locked page, will result in a FLASH Error device reset. Accessing FLASH from user firmware executing on a locked page: 1. 2. 3. 4. 5. 6. 7. Any unlocked page except the page containing the Lock Byte may be read, written, or erased. Any locked page except the page containing the Lock Byte may be read, written, or erased. The page containing the Lock Byte cannot be erased. It may only be read or written. Reading the contents of the Lock Byte is always permitted. Locking additional pages (changing 1s to 0s in the Lock Byte) is not permitted. Unlocking FLASH pages (changing 0s to 1s in the Lock Byte) is not permitted. The Reserved Area cannot be read, written, or erased. Any attempt to access the reserved area, or any other locked page, will result in a FLASH Error device reset. 132 Rev. 1.2 C8051F388/9/A/B SFR Definition 18.1. PSCTL: Program Store R/W Control Bit 7 6 5 4 3 2 Name 1 0 PSEE PSWE Type R R R R R R R/W R/W Reset 0 0 0 0 0 0 0 0 SFR Address =0x8F; SFR Page = All Pages Bit Name 7:2 Function Reserved Must write 000000b. 1 PSEE Program Store Erase Enable. Setting this bit (in combination with PSWE) allows an entire page of Flash program memory to be erased. If this bit is logic 1 and Flash writes are enabled (PSWE is logic 1), a write to Flash memory using the MOVX instruction will erase the entire page that contains the location addressed by the MOVX instruction. The value of the data byte written does not matter. 0: Flash program memory erasure disabled. 1: Flash program memory erasure enabled. 0 PSWE Program Store Write Enable. Setting this bit allows writing a byte of data to the Flash program memory using the MOVX write instruction. The Flash location should be erased before writing data. 0: Writes to Flash program memory disabled. 1: Writes to Flash program memory enabled; the MOVX write instruction targets Flash memory. Rev. 1.2 133 C8051F388/9/A/B SFR Definition 18.2. FLKEY: Flash Lock and Key Bit 7 6 5 4 3 Name FLKEY[7:0] Type R/W Reset 0 0 0 0 0 2 1 0 0 0 0 SFR Address = 0xB7; SFR Page = All Pages Bit Name Function 7:0 FLKEY[7:0] Flash Lock and Key Register. Write: This register provides a lock and key function for Flash erasures and writes. Flash writes and erases are enabled by writing 0xA5 followed by 0xF1 to the FLKEY register. Flash writes and erases are automatically disabled after the next write or erase is complete. If any writes to FLKEY are performed incorrectly, or if a Flash write or erase operation is attempted while these operations are disabled, the Flash will be permanently locked from writes or erasures until the next device reset. If an application never writes to Flash, it can intentionally lock the Flash by writing a non-0xA5 value to FLKEY from software. Read: When read, bits 1–0 indicate the current Flash lock state. 00: Flash is write/erase locked. 01: The first key code has been written (0xA5). 10: Flash is unlocked (writes/erases allowed). 11: Flash writes/erases disabled until the next reset. 134 Rev. 1.2 C8051F388/9/A/B SFR Definition 18.3. FLSCL: Flash Scale Bit 7 6 5 Name FOSE Reserved FLRT Reserved Type R/W R/W R/W R/W Reset 1 0 0 4 0 SFR Address = 0xB6; SFR Page = All Pages Bit Name 7 FOSE 6:5 Reserved 4 FLRT 3:0 Reserved 3 0 2 0 1 0 0 0 Function Flash One-shot Enable. This bit enables the Flash read one-shot. When the Flash one-shot disabled, the Flash sense amps are enabled for a full clock cycle during Flash reads. At system clock frequencies below 10 MHz, disabling the Flash one-shot will increase system power consumption. 0: Flash one-shot disabled. 1: Flash one-shot enabled. Must write 00b. FLASH Read Time. This bit should be programmed to the smallest allowed value, according to the system clock speed. 0: SYSCLK