0
登录后你可以
  • 下载海量资料
  • 学习在线课程
  • 观看技术视频
  • 写文章/发帖/加入社区
会员中心
创作中心
发布
  • 发文章

  • 发资料

  • 发帖

  • 提问

  • 发视频

创作活动
CP2401DK

CP2401DK

  • 厂商:

    SILABS(芯科科技)

  • 封装:

    -

  • 描述:

    KIT EVAL I2C LCD DRIVER CP2401

  • 数据手册
  • 价格&库存
CP2401DK 数据手册
C P2 4 0 0 / 1 -DK CP2400 C P 2 4 0 1 D EVELOPMENT K IT U S E R ’ S G U I D E AND es ig ns 1. Overview The LCD Development Kits (CP2400-DK and CP2401-DK) provide all the hardware and software required to develop and test LCD applications. The CP240x LCD Firmware Library is included to aid in the code development process and handle the communication between the C8051F9xx MCU and the CP2400/1 LCD controller. The LCD library can be used to communicate with the LCD controller through the SPI interface (CP2400-DK) or the SMBus interface (CP2401-DK). Example code using the LCD library is included with both development kits. N ew D The LCD development kit hardware includes a C8051F930 target board, CP2400 or CP2401 LCD Development Board, USB Debug adapter, and an ac to dc power adapter. The C8051F930 Target Board features the 25 MIPS, 64 kB Flash, over 4 kB RAM, 8051-based C8051F930 MCU. The C8051F930 MCU is part of the low-power family and can operate with a supply voltage from 0.9 to 3.6 V. The MCU LCD interface provided by the AB board consists of the CP2400/1 LCD controller and an LCD and is compatible with the C8051F930-DK and C8051F912DK. The LCD development kit includes example code which uses either the SPI interface (CP2400-DK) or SMBus interface (CP2401-DK) on the C8051F930 to control the LCD using the LCD library. N ot R ec om m en de d fo r The Silicon Labs’ IDE supports full-speed, non-intrusive MCU debugging and is bundled with an evaluation version of the Keil C51 Toolchain allowing immediate application code evaluation in C. Projects with up to 4 kB of object code and unlimited library code can be developed using the included toolset. Numerous application code examples are included in the development kit and a walkthrough of an LCD example is included in 6. "Example Source Code‚" on page 11. Figure 1. C8051F912-TB Target Board and CP2400 LCD Development Board Rev. 0.1 10/09 Copyright © 2009 by Silicon Laboratories CP2400/1-DK CP2400/1-DK 2. Kit Contents The CP2400/1 LCD development kit contains the following items:  C8051F930 target board CP2400 or CP2401 LCD development board  CP240x development kit quick-start guide  Silicon Laboratories IDE and product information CD-ROM. CD content includes the following: Silicon Laboratories Integrated Development Environment (IDE) 8051 development tools (macro assembler, linker, evaluation C compiler) Source code examples and register definition files Documentation CP2400 and CP2401 Development Kit User’s Guide (this document) Keil  AC to DC power adapter USB Debug Adapter (USB to debug interface)  2 USB cables  2 AAA batteries Figure 2. C8051F930 Target Board N ot R ec om m en de d fo r N ew D  es ig ns  2 Rev. 0.1 fo r N ew D es ig ns CP2400/1-DK m en de d Figure 3. CP2400 Development Board 3. Software Overview All software required to develop firmware and communicate with the target microcontroller is included in the CDROM. The CD-ROM also includes other useful software. Below is the software necessary for firmware development and communication with the target microcontroller:  Silicon Laboratories Integrated Development Environment (IDE)  Keil 8051 development tools (macro assembler, linker, evaluation C compiler) Other useful software that is provided in the CD-ROM includes the following:  om Configuration Wizard 2  Keil µVision drivers  CP210x USB to UART Virtual COM Port (VCP) drivers ec 3.1. Software Installation N ot R The included CD-ROM contains the Silicon Laboratories Integrated Development Environment (IDE), Keil software 8051 tools and additional documentation. Insert the CD-ROM into your PC’s CD-ROM drive. An installer will automatically launch, allowing you to install the IDE software or read documentation by clicking buttons on the Installation Panel. If the installer does not automatically start when you insert the CD-ROM, run autorun.exe found in the root directory of the CD-ROM. Refer to the ReleaseNotes.txt file on the CD-ROM for the latest information regarding known problems and restrictions. After installing the software, see the following sections for information regarding the software and running one of the demo applications. 3.2. CP210x USB to UART VCP Driver Installation The C8051F930 Target Board includes a Silicon Laboratories CP2103 USB-to-UART Bridge Controller. Device drivers for the CP2103 need to be installed before PC software such as HyperTerminal can communicate with the target board over the USB connection. If the "Install CP210x Drivers" option was selected during installation, this will launch a driver “unpacker” utility. Rev. 0.1 3 CP2400/1-DK 1. Follow the steps to copy the driver files to the desired location. The default directory is C:\Silabs\MCU\CP210x. 2. The final window will give an option to install the driver on the target system. Select the “Launch the CP210x VCP Driver Installer” option if you are ready to install the driver. es ig ns 3. If selected, the driver installer will now launch, providing an option to specify the driver installation location. After pressing the “Install” button, the installer will search your system for copies of previously installed CP210x Virtual COM Port drivers. It will let you know when your system is up to date. The driver files included in this installation have been certified by Microsoft. 4. If the “Launch the CP210x VCP Driver Installer” option was not selected in step 3, the installer can be found in the location specified in step 2, by default C:\Silabs\MCU\CP210x\Windows_2K_XP_S2K3_Vista. At this location run CP210xVCPInstaller.exe. D 5. To complete the installation process, connect the included USB cable between the host computer and the USB connector (P3) on the C8051F930 Target Board. Windows will automatically finish the driver installation. Information windows will pop up from the taskbar to show the installation progress. N ew 6. If needed, the driver files can be uninstalled by selecting “Silicon Laboratories CP210x USB to UART Bridge (Driver Removal)” option in the “Add or Remove Programs” window. 3.3. Silicon Laboratories IDE The Silicon Laboratories IDE integrates a source-code editor, a source-level debugger, and an in-system Flash programmer. See Section 5. "Using the Keil Software 8051 Tools with the Silicon Laboratories IDE‚" on page 10 for detailed information on how to use the IDE. The Keil Evaluation Toolset includes a compiler, linker, and assembler and easily integrates into the IDE. The use of third-party compilers and assemblers is also supported. m en de d fo r 3.3.1. IDE System Requirements The Silicon Laboratories IDE requirements:  Pentium-class host PC running Microsoft Windows 2000 or newer  One available USB port  64 MB RAM and 40 MB free HD space recommended om 3.3.2. 3rd Party Toolsets The Silicon Laboratories IDE has native support for many 8051 compilers. The full list of natively supported tools is as follows:  Keil  IAR  Raisonance  Tasking  Hi-Tech  SDCC The demo applications for the C8051F930 target board are written to work with the Keil and SDCC toolsets. ec 3.4. Keil Evaluation Toolset R 3.4.1. Keil Assembler and Linker The Keil demonstration toolset assembler and linker place no restrictions on code size. N ot 3.4.2. Keil Evaluation C51 C Compiler The evaluation version of the C51 compiler is the same as the full version with the following limitations: (1) Maximum 4 kB code generation, (2) There is no floating point library included. When installed from the CD-ROM, the C51 compiler is initially limited to a code size of 2 kB, and programs start at code address 0x0800. Refer to “AN104: Integrating Keil Tools into the Silicon Labs IDE" for instructions to change the limitation to 4 kB and have the programs start at code address 0x0000. 4 Rev. 0.1 CP2400/1-DK 3.5. Configuration Wizard 2 m en de d fo r N ew D es ig ns The Configuration Wizard 2 is a code generation tool for all of the Silicon Laboratories devices. Code is generated through the use of dialog boxes for each of the device's peripherals. Figure 4. Configuration Wizard 2 Utility N ot R ec om The Configuration Wizard utility helps accelerate development by automatically generating initialization source code to configure and enable the on-chip resources needed by most design projects. In just a few steps, the wizard creates complete startup code for a specific Silicon Laboratories MCU. The program is configurable to provide the output in C or assembly language. For more information, refer to the Configuration Wizard documentation. Documentation and software is available on the kit CD and from the downloads webpage: www.silabs.com/ mcudownloads. Rev. 0.1 5 CP2400/1-DK 3.6. Silicon Labs Battery Life Estimator m en de d fo r N ew D es ig ns The Battery Life Estimator is a system design tool for battery operated devices. It allows the user to select the type of battery they are using in the system and enter the supply current profile of their application. Using this information, it performs a simulation and provides an estimated system operating time. The Battery Life Estimator is shown in Figure 5. Figure 5. Battery Life Estimator Utility ec om From Figure 5, the two inputs to the Battery Life Estimator are battery type and discharge profile. The utility includes battery profiles for common battery types such as AAA, AA, A76 Button Cell, and CR2032 coin cell. The discharge profile is application-specific and describes the supply current requirements of the system under various supply voltages and battery configurations. The discharge profile is independent of the selected power source. Several read-only discharge profiles for common applications are included in the pulldown menu. The user may also create a new profile for their own applications. R To create a new profile: 1. Select the profile that most closely matches the target application or choose the "Custom Profile". 2. Click Manage N ot 3. Click Duplicate 4. Click Edit Profiles may be edited with the easy-to-use GUI (shown in Figure 6). 6 Rev. 0.1 om m en de d fo r N ew D es ig ns CP2400/1-DK ec Figure 6. Battery Life Estimator Discharge Profile Editor R The Discharge Profile Editor allows the user to modify the profile name and description. The four text entry boxes on the left hand side of the form allow the user to specify the amount of time the system spends in each power mode. On the right hand side, the user may specify the supply current of the system in each power mode. N ot Since supply current is typically dependent on supply voltage, the discharge profile editor provides two columns for supply current. The V2 and V1 voltages at the top of the two columns specify the voltages at which the current measurements were taken. The Battery Life Estimator creates a linear approximation based on the input data and is able to feed the simulation engine with an approximate supply current demand for every input voltage. The minimum system operating voltage input field allows the system operating time to stop increasing when the simulated battery voltage drops below a certain threshold. This is primarily to allow operating time estimates for systems that cannot operate down to 1.8 V, which is the voltage of two fully drained single-cell batteries placed in series. Rev. 0.1 7 CP2400/1-DK The wakeup frequency box calculates the period of a single iteration through the four power modes and displays the system wake up frequency. This is typically the "sample rate" in low power analog sensors. m en de d fo r N ew D es ig ns Once the battery type and discharge profile is specified, the user can click the "Simulate" button to start a new simulation. The simulation engine calculates the estimated battery life when using one single-cell battery, two single-cell batteries in series, and two single-cell batteries in parallel. Figure 7 shows the simulation output window. Figure 7. Battery Life Estimator Utility Simulation Results Form om The primary outputs of the Battery Life Estimator are an estimated system operating time and a simulated graph of battery voltage vs. time. Additional outputs include estimated battery capacity, average current, self-discharge current, and the ability to export graph data to a comma delimited text file for plotting in an external graphing application. 3.7. Keil µVision2 and µVision3 Silicon Laboratories Drivers N ot R ec As an alternative to the Silicon Laboratories IDE, the µVision debug driver allows the Keil µVision2 and µVision3 IDEs to communicate with Silicon Laboratories’ on-chip debug logic. In-system Flash memory programming integrated into the driver allows for rapid updating of target code. The µVision2 and µVision3 IDEs can be used to start and stop program execution, set breakpoints, check variables, inspect and modify memory contents, and single-step through programs running on the actual target hardware. For more information, refer to the µVision driver documentation. The documentation and software are available on the kit CD and from the downloads webpage: www.silabs.com/mcudownloads. 8 Rev. 0.1 CP2400/1-DK 4. Hardware Setup using a USB Debug Adapter The target board is connected to a PC running the Silicon Laboratories IDE via the USB Debug Adapter as shown in Figure 9. es ig ns 1. Connect the LCD development board to the F930 target board as shown in Figure 8. 2. Connect the USB Debug Adapter to the DEBUG connector on the C8051F930 target board with the 10-pin ribbon cable. 3. Connect one end of the USB cable to the USB connector on the USB Debug Adapter. 4. Connect the other end of the USB cable to a USB Port on the PC. 5. Verify that a shorting block is installed on J17 and that SW5 is in the ON position on the C8051F930 target board. D 6. Verify that a shorting block is installed on J2 of the CP2400/1 LCD Development Board. 7. Connect the ac/dc power adapter to power jack P1 on the C8051F930 target board (Optional). Notes: Use the Reset button in the IDE to reset the target when connected using a USB Debug Adapter. Remove power from the target board and the USB Debug Adapter before connecting or disconnecting the ribbon cable from the target board. Connecting or disconnecting the cable when the devices have power can damage the device and/or the USB Debug Adapter. P1.6 fo r R15 J16 P1.5 J15 CP 2103 U3 SILICON LABS CP2400-GQ LCD DEVELOPMENT BOARD J5 U1 +1VD J11 COIN_CELL J7 J3 D1 J5J4 PWR +3VD J14 RESET VDD/DC+ IMEASURE ` J5 J2 J17 H2 D2 LED VBAT AAA_BAT WALL_PWR J13 J6 SILICON LABS www.silabs.com J1 J9 J12 F930 J2 IMEASURE J8 VBAT OFF ON SW5 H1 1 CELL m en de d www.silabs.com U1 CP2400 USB POWER P3 TOUCH SENSE SWITCH P2.1 2 CELL J4 P0.3 DEBUG TOUCH SENSE SWITCH P2.0 P0.2 POWER OFF BEFORE SWITCHING MODE P1 J10  N ew  SW4 J1 P2 PC Target Board P1.6 TOUCH SENSE SWITCH P2.0 LED DEBUG J11 COIN_CELL J3 J14 VBAT POWER OFF BEFORE SWITCHING MODE AAA_BAT WALL_PWR J13 +3VD RESET J6 J5J4 J5 D2 PWR VDD/DC+ H1 IMEASURE ` J2 J17 H2 OFF ON SW5 1 CELL F930 J7 IMEASURE D1 SW4 VBAT J1 Power J9 J12 +1VD J10 N ot J1 J8 U1 Run U3 SILICON LABS Silicon Laboratories USB DEBUG ADAPTER CP 2103 J4 J2 SILICON LABS www.silabs.com USB Debug Adapter TOUCH SENSE SWITCH P2.1 www.silabs.com J5 P0.3 USB POWER P3 J15 CP2400-GQ LCD DEVELOPMENT BOARD U1 CP2400 P0.2 P1.5 J16 R P1 R15 USB Cable Stop LCD Development Board 2 CELL ec om Figure 8. CP2400/1 LCD Development Board Attachment AC/DC Adapter P2 Figure 9. Hardware Setup Using a USB Debug Adapter Rev. 0.1 9 CP2400/1-DK 5. Using the Keil Software 8051 Tools with the Silicon Laboratories IDE es ig ns To perform source-level debugging with the IDE, configure the Keil 8051 tools to generate an absolute object file in the OMF-51 format with object extensions and debug records enabled. Build the OMF-51 absolute object file by calling the Keil 8051 tools at the command line (e.g., batch file or make file) or by using the project manager built into the IDE. The default configuration when using the Silicon Laboratories IDE project manager enables object extension and debug record generation. Refer to "AN104: Integrating Keil 8051 Tools into the Silicon Labs IDE" in the “Silabs\MCU\Documentation\ApplicationNotes” directory on the CD-ROM for additional information on using the Keil 8051 tools with the Silicon Laboratories IDE. To build an absolute object file using the Silicon Laboratories IDE project manager, you must first create a project. A project consists of a set of files, IDE configuration, debug views, and a target build configuration (list of files and tool configurations used as input to the assembler, compiler, and linker when building an output object file). N ew D The following sections illustrate the steps necessary to manually create a project with one or more source files, build a program, and download it to the target in preparation for debugging. (The IDE will automatically create a single-file project using the currently open and active source file if you select Build/Make Project before a project is defined.) 5.1. Creating a New Project 1. Select ProjectNew Project to open a new project and reset all configuration settings to default. 2. Select FileNew File to open an editor window. Create your source file(s) and save the file(s) with a recognized extension, such as .c, .h, or .asm, to enable color syntax highlighting. fo r 3. Right-click on “New Project” in the Project Window. Select Add files to project. Select files in the file browser and click Open. Continue adding files until all project files have been added. m en de d 4. For each of the files in the Project Window that you want assembled, compiled and linked into the target build, right-click on the file name and select Add file to build. Each file will be assembled or compiled as appropriate (based on file extension) and linked into the build of the absolute object file. 5. If a project contains a large number of files, the “Group” feature of the IDE can be used to organize. Right-click on “New Project” in the Project Window. Select Add Groups to project. Add pre-defined groups or add customized groups. Right-click on the group name and choose Add file to group. Select files to be added. Continue adding files until all project files have been added. 5.2. Building and Downloading the Program for Debugging om 1. Once all source files have been added to the target build, build the project by clicking on the Build/Make Project button in the toolbar or selecting ProjectBuild/Make Project from the menu. Note: After the project has been built the first time, the Build/Make Project command will only build the files that have been changed since the previous build. To rebuild all files and project dependencies, click on the Rebuild All button in the toolbar or select ProjectRebuild All from the menu. ec 2. Before connecting to the target device, several connection options may need to be set. Open the Connection Options window by selecting OptionsConnection Options... in the IDE menu. First, select the appropriate adapter in the “Serial Adapter” section. Next, the correct “Debug Interface” must be selected. C8051F93xC8051F92x family devices use the Silicon Labs 2-wire (C2) debug interface. Once all the selections are made, click the OK button to close the window. R 3. Click the Connect button in the toolbar or select DebugConnect from the menu to connect to the device. N ot 4. Download the project to the target by clicking the Download Code button in the toolbar. Note: To enable automatic downloading if the program build is successful select Enable automatic connect/ download after build in the ProjectTarget Build Configuration dialog. If errors occur during the build process, the IDE will not attempt the download. 5. Save the project when finished with the debug session to preserve the current target build configuration, editor settings and the location of all open debug views. To save the project, select ProjectSave Project As... from the menu. Create a new name for the project and click on Save. 10 Rev. 0.1 CP2400/1-DK 6. Example Source Code es ig ns Example source code and register definition files are provided in the “SiLabs\MCU\Examples\C8051F93x_92x\” default directory during IDE installation. These files may be used as a template for code development. Example applications include a blinking LED example which configures the green LED on the target board to blink at a fixed rate. 6.1. Register Definition Files N ew D Register definition files C8051F930.inc and C8051F930_defs.h define all SFR registers and bit-addressable control/status bits. A macro definition header file compiler_defs.h is also included, and is required to be able to use the C8051F930_defs.h header file with various tool chains. These files are installed into the “Silabs\MCU\Examples\C8051F93x_92x\Header_Files\” directory during IDE installation by default. The register and bit names are identical to those used in the C8051F93x-C8051F92x data sheet. These register definition files are also installed in the default search path used by the Keil Software 8051 tools. Therefore, when using the Keil 8051 tools included with the development kit (A51, C51), it is not necessary to copy a register definition file to each project’s file directory. 6.2. Blinking LED Example fo r The example source files F93x_Blinky.asm and F93x_Blinky.c installed in the default directory “Silabs\MCU\Examples\C8051F93x_92x\Blinky” show examples of several basic C8051F930 functions. These include disabling the watchdog timer (WDT), configuring the Port I/O crossbar, configuring a timer for an interrupt routine, initializing the system clock, and configuring a GPIO port pin. When compiled/assembled and linked this program flashes the green LED on the C8051F930 Target Board about five times a second using the interrupt handler with a C8051F930 timer. 6.3. Touch Sensitive Switch Example m en de d The example source file F93x_CapTouchSense_Switch.c demonstrates the configuration and usage of the touch sensitive (contactless) switches located on P2.0 and P2.1. Refer to the source file for step-by-step instructions to build and test this example. This is installed in the following directory by default: Silabs\MCU\Examples\C8051F93x_92x\ CapTouchSense_Switch 6.4. LCD Examples om The example source files in the project CP240x_LCD_Example show how to initialize the C8051F9xx as well as the CP2400/1. The project uses the LCD library to configure the CP2400/1 through the SPI interface (CP2400) or SMBus interface (CP2401). This project contains many examples that can be selected and customized through modifications to header files. This is installed in the following directory by default: Silabs\MCU\Examples\CP240x\CP240x_LCD_Example\Source R ec 6.4.1. Target Board Selection The target board that is connected to the CP2400/1 LCD Development Board must be specified in the file lcd_lib_portdefs.h. The section labeled “Development Board Definition” has a global definition that specifies which target board is connected to the CP2400/1 LCD development board. It is important to note that the target board specified in this section must match the target board that is connected to the CP2400/1 LCD development board. The following line of code would configure the code to use the C8051F930 target board: #define DEV_BOARD F930DK N ot 6.4.2. Control Interface Selection The control interface that is used to configure the CP2400/1 can be selected by modifying the file, lcd_lib_portdefs.h. In this file, there is a section called “Interface Definition” where either the SPI interface (CP2400) or the SMBus interface (CP2401) can be selected. It is important to note that the correct control interface must be selected in this particular header file before compiling the project or the CP2400/1 will not function correctly. The CP2400 uses the SPI interface, and the CP2401 uses the SMBus interface. The following line of code would configure the code to use the SMBus interface to configure a CP2401: #define BUS_INTERFACE SMBUS Rev. 0.1 11 CP2400/1-DK If using a CP2400, this line should say: #define BUS_INTERFACE SPI #define EXAMPLE es ig ns 6.4.3. Example Selection The example that is run on the CP2400/1 LCD development board can be selected in the file, app_config.h. The available examples include a voltage display example, digit display example, and several current measurement examples. A list of available examples is included in the file, app_config.h. The following line of code would select the digit display example: DISPLAY_DIGITS N ew D The display digits example will first show the numbers “01234567”, clear the LCD, and then show “76543210”. For the voltage display example, the channel being measured can be selected by modifying the CHANNEL_SELECT definition in app_config.h. The available selections are VDD and the potentiometer (POT). To measure VDD, change the corresponding EXAMPLE definition in app_config.h. The VDD voltage will now be displayed on the LCD. To measure the potentiometer voltage, change the corresponding EXAMPLE definition in app_config.h, and place shorting blocks on J16 and J15[2-3] on the C8501F930 Target Board. The potentiometer voltage will now be displayed on the LCD. N ot R ec om m en de d fo r The various current measurement examples can also be selected in app_config.h. These examples place the CP240x in various power modes. The file, lcd_lib_config.h, has parameters that can be modified that will affect the current draw, such as the LCD refresh rate, the mux mode, and the bias mode. 12 Rev. 0.1 CP2400/1-DK 7. C8051F930 Target Board fo r N ew D Expansion connector (96-pin) Power connector (accepts input from 7 to 15 VDC unregulated power adapter) USB connector (connects to PC for serial communication) Enable/Disable VBAT Power LED Port I/O headers (provide access to Port I/O pins) Enable/Disable VDD/DC+ Power LED Provides an easily accessible ground clip Connects pin P0.7 (IREF0 Output) to resistor R14 and capacitor C19 Connects P0.2 and P0.3 to switches and P1.5 and P1.6 to LEDs DEBUG connector for Debug Adapter interface Selects the power supply source (Wall Power, AAA Battery, or Coin Cell) Connects Port I/O to UART0 interface Connects external VREF capacitor to the P0.0/VREF Connects the PCB ground plane to P0.1/AGND Connects negative potentiometer (R14) terminal to pin P1.4 or to GND Connects the potentiometer (R14) wiper to P0.6/CNVSTR Creates an open in the power supply path to allow supply current measurement Analog I/O terminal block Provides terminal block access to the input and output nodes of J17 Switches the device between One-Cell (0.9–1.8 V supply) or Two-Cell (1.8–3.6 V) mode Turns power to the MCU on or off m en de d R15 om ec +1VD J11 COIN_CELL J7 AAA_BAT WALL_PWR J13 SW1 J14 J3 +3VD RESET J6 VDD/DC+ J5 IMEASURE PORT0 ` J2 J17 H2 OFF ON H1 J9 J12 F930 PORT1 R J8 U1 P1 N ot U3 SILICON LABS www.silabs.com PORT2 CP 2103 VBAT Pin 1 Pin 2 SW4 VBAT SW5 1 CELL J4 USB POWER P3 TOUCH SENSE SWITCH P2.1 2 CELL TOUCH SENSE SWITCH P2.0 P0.3 SW3 DEBUG P1.4 J15 GND P0.2 P1.5 SW2 POWER OFF BEFORE SWITCHING MODE J16 P1.6 J10 P1 P2 P3 J1 J2, J3, J4 J5 J6 J7 J8 J9 J10, J11 J12 J13 J14 J15 J16 J17 H1 H2 SW4 SW5 es ig ns The CP2400/1 Development Kit includes a target board with a C8051F930 device pre-installed for evaluation and preliminary software development. Numerous input/output (I/O) connections are provided to facilitate prototyping using the target board. Refer to Figure 10 for the locations of the various I/O connectors. Figure 12 on page 15 shows the factory default shorting block positions. J1 P2 Pin 1 Figure 10. C8051F930 Target Board Rev. 0.1 13 CP2400/1-DK The following items are located on the bottom side of the board. See Figure 11. Battery Holder for 1.5 V AAA. Use for one-cell or two-cell mode. Battery Holder for 1.5 V AAA. Use for two-cell mode only. Battery Holder for 3 V Coin Cell (CR2032). Battery Holder for 1.5 V Button Cell (A76 or 357). NEG es ig ns BT1 BT2 BT3 BT4 POS BT3 (CR2032) BT1 NEG (AAA) m en de d BT4 (A76 or 357) fo r BT2 (AAA) POS N ew D Note: BT2 is only used in two-cell mode. N ot R ec om Figure 11. Bottom of C8051F930 Target Board 14 Rev. 0.1 CP2400/1-DK 7.1. Target Board Shorting Blocks: Factory Defaults P1.6 R15 USB POWER P3 TOUCH SENSE SWITCH P2.0 TOUCH SENSE SWITCH P2.1 CP 2103 U3 SILICON LABS PORT2 J8 U1 N ew +1VD F930 P1 J9 J12 J11 J13 AAA_BAT WALL_PWR SW1 J14 +3VD J7 PORT1 J3 J6 VDD/DC+ H1 PORT0 IMEASURE ` J2 m en de d J5 fo r RESET J17 H2 OFF ON SW5 VBAT POWER OFF BEFORE SWITCHING MODE J10 COIN_CELL 1 CELL www.silabs.com Pin 1 Pin 2 2 CELL J4 D P1.4 J15 GND P0.3 SW3 DEBUG J16 P0.2 P1.5 SW2 es ig ns The C8051F930 target board comes from the factory with pre-installed shorting blocks on many headers. Figure 12 shows the positions of the factory default shorting blocks. SW4 VBAT J1 P2 Pin 1 N ot R ec om Figure 12. C8051F930 Target Board Shorting Blocks: Factory Defaults Rev. 0.1 15 CP2400/1-DK 7.2. Target Board Power Options and Current Measurement es ig ns The C8051F930 Target Board supports three power options, selectable by the three-way header (J10/J11). The power options vary based on the configuration (one-cell or two-cell mode) selected by SW4. Power to the MCU may be switched on/off using the power switch (SW5). Important Note: The power switch (SW5) must be in the OFF position prior to switching between one-cell and two-cell mode using SW4. The power options are described in the paragraphs below.  9 VDC power using the ac to dc power adapter (P2) 5 VDC USB VBUS power from PC via the USB Debug Adapter (J9)  5 VDC USB VBUS power from PC via the CP2103 USB connector (P3)  D 7.2.1. Wall Power When the J10/J11 three-way header is set to WALL_PWR, the C8051F930 Target Board may be powered from the following power sources: N ew All the three power sources are ORed together using reverse-biased diodes (D1, D2, D3), eliminating the need for headers to choose between the sources. The target board will operate as long as any one of the power sources is present. The ORed power is regulated to a 3.3 V dc voltage using a LDO regulator (U2). The output of the regulator powers the +3 VD net on the target board. fo r If SW4 is configured to select two-cell mode, the VBAT supply net on the target board is powered directly from the +3 VD net. If SW4 is configured to select one-cell mode, the VBAT supply net is powered directly from the +1 VD. This power supply net takes +3 VD and passes it through a 1.65 V LDO. The LDO’s output voltage is variable and can be set by changing the value of resistor R32. J11 J10 COIN_CELL m en de d AAA_BAT WALL_PWR VBAT 7.2.2. AAA Battery When the J10/J11 three-way header is set to AAA_BAT, the C8051F930 Target Board may be powered from a single AAA battery inserted in BT1 or from the series combination of the AAA batteries inserted in BT1 and BT2. A single battery is selected when SW4 is configured to one-cell mode. The two AAA batteries configured in series to provide a voltage of ~3 V are selected when SW4 is configured to two-cell mode. J10 COIN_CELL VBAT AAA_BAT WALL_PWR ec om J11 16 J11 COIN_CELL J10 N ot R 7.2.3. Coin Cell Battery When the J10/J11 three-way header is set to COIN_CELL, the C8051F930 Target Board may be powered from a single 1.5 V Alkaline (A76) or Silver Oxide (357) button cell inserted in BT4 or from a single 3 V Lithium (CR2032) coin cell inserted in BT3. The button cell (BT4) is selected when SW4 is configured to one-cell mode, and the coin cell (BT3) is selected when SW4 is configured to two-cell mode. AAA_BAT WALL_PWR Rev. 0.1 VBAT CP2400/1-DK es ig ns 7.2.4. Measuring Current The header (J17) and terminal block (H2) provide a way to measure the total supply current flowing from the power supply source to the MCU. The measured current does not include any current from the VBAT LED (DS2), the address latch (U4) or the quiescent current from the power supply; however, it does include the current used by any LEDs powered from the VDD/DC+ supply net or sourced through a GPIO pin. See the target board schematics in Figures 19 through 21 for additional information. 7.3. System Clock Sources N ew D 7.3.1. Internal Oscillators The C8051F930 device installed on the target board features a factory calibrated programmable high-frequency internal oscillator (24.5 MHz base frequency, ±2%) and a low power internal oscillator (20 MHz ±10%). After each reset, the low power oscillator divided by 8 results in a default system clock frequency of 2.5 MHz (±10%). The selected system clock and the system clock divider may be configured by software for operation at other frequencies. For low-frequency operation, the C8051F930 features a smaRTClock real time clock. A 32.768 kHz Watch crystal (Y2) is included on the target board. If you wish to operate the C8051F930 device at a frequency not available with the internal oscillators, an external crystal may be used. Refer to the C8051F93x-C8051F92x data sheet for more information on configuring the system clock source. 7.4. Port I/O Headers (J2, J3, J4, J6) fo r 7.3.2. External Oscillator Options The target board is designed to facilitate the installation of an external crystal (Y1). Install a 10 M resistor at R9 and install capacitors at C20 and C21 using values appropriate for the crystal you select. If you wish to operate the external oscillator in capacitor or RC mode, options to install a capacitor or an RC network are also available on the target board. Populate C21 for capacitor mode, and populate R16 and C21 for RC mode. Refer to the C8051F93xC8051F92x data sheet for more information on the use of external oscillators. m en de d Access to all Port I/O on the C8051F930 is provided through the headers J2, J3, and J4. The header J6 provides access to the ground plane for easy clipping of oscilloscope probes. 7.5. Switches and LEDs Three push-button switches are provided on the target board. Switch SW1 is connected to the reset pin of the C8051F930. Pressing SW1 puts the device into its hardware-reset state. Switches SW2 and SW3 are connected to the C8051F930’s general purpose I/O (GPIO) pins through headers. Pressing SW2 or SW3 generates a logic low signal on the port pin. Remove the shorting block from the header (J8) to disconnect the switches from the port pins. The port pin signal is also routed to pins on the J2 and P1 I/O connectors. See Table 1 for the port pins and headers corresponding to each switch. om Two touch sensitive (contactless) switches are provided on the target board. The operation of these switches require appropriate firmware running on the C8051F930 MCU that can sense the state of the switch. See Section 6.3. "Touch Sensitive Switch Example‚" on page 11 for details about example source code. R ec Five power LEDs are provided on the target board to serve as indicators. Each of the two regulators has a red LED used to indicate the presence of power at the output of the regulator. A red USB Power LED turns on when a USB cable is plugged into the USB connector P3. One power LED is also added to each of the two primary supply nets powering the MCU (VDD/DC+ and VBAT). The LEDs connected to the supply nets may be disabled by removing the shorting blocks from J1 and J5. N ot Two LEDs are connected to GPIO pins P1.5 and P1.6 for use by application software. See Table 1 for the port pins and headers corresponding to each LED. A potentiometer (R15) is also provided on the target board for generating analog signals. Place a shorting block on J16 to connect the wiper to P0.6/CNVSTR. The header J15 allows the negative terminal of the potentiometer to be tied to GND or to P1.4. When tied to GND, the potentiometer is always enabled and will draw a measurable amount of supply current. When tied to P1.4, it only draws current when P1.4 is driving a logic 0 and draws no current when P1.4 is driving a logic 1. Rev. 0.1 17 CP2400/1-DK Table 1. Target Board I/O Descriptions I/O Header(s) SW1 SW2 SW3 P2.0 (Touch Sense Switch) P2.1 (Touch Sense Switch) Red LED (P1.5) Yellow LED (P1.6) Red LED (VDD/DC+) Red LED (VBAT) Red LED (USB Power) Red LED (+1 VD Power) Red LED (+3 VD Power) Potentiometer (R15) Reset P0.2 P0.3 P2.0 P2.1 P1.5 P1.6 VDD/DC+ Supply Net VBAT Supply Net USB VBUS +1 VD Regulator Output +3 VD Regulator Output P0.6/P1.4 none J8[5–6] J8[7–8] none none J8[1–2] J8[3–4] J5 J1 none none none J15, J16 N ew D es ig ns Description 7.6. Expansion I/O Connector (P1) fo r The 96-pin Expansion I/O connector P1 provides access to all signal pins of the C8051F930 device (except the C2 debug interface signals). In addition, power supply and ground pins are included. A small through-hole prototyping area is also provided. See Table 2 for a list of pin descriptions for P1. Table 2. P1 Pin Descriptions Description Row B Pin # Description Row C Pin # Description 1 +3 VD 1 GND 1 nc nc 2 nc 2 nc nc 3 nc 3 nc nc 4 nc 4 nc nc 5 nc 5 nc nc 6 nc 6 nc nc 7 nc 7 nc 8 nc 8 nc 8 nc 9 nc 9 nc 9 nc 10 nc 10 P0.7/IREF0 10 P0.6/CNVSTR 11 P0.5/RX 11 P0.4/TX 11 P0.3H 12 P0.2H 12 P0.1/AGND 12 P0.0/VREF 13 P1.7/AD7 13 P1.6/AD6 13 P1.5/AD5 14 P1.4/AD4 14 P1.3/AD3 14 P1.2/AD2 15 P1.1/AD1 15 P1.0/AD0 15 A7-Latch 16 A6-Latch 16 A5-Latch 16 A4-Latch 17 A3-Latch 17 A2-Latch 17 A1-Latch 18 A0-Latch 18 P2.3/A11 18 nc 2 3 4 5 6 N ot R ec om 7 m en de d Row A Pin # 18 Rev. 0.1 CP2400/1-DK Row A Pin # Description Row B Pin # Description Row C Pin # Description 19 nc 19 nc 19 P2.3/A11 20 P2.2/A10 20 P2.1/A9 20 21 /WR 21 /RD 21 22 P2.3/A11 22 P2.2/A10 22 23 P2.0/A8 23 ALE 23 24 nc 24 nc 24 25 nc 25 GND 25 es ig ns Table 2. P1 Pin Descriptions (Continued) 26 GND 26 nc 26 27 nc 27 nc 27 28 nc 28 VDD/DC+ 28 VBAT 29 nc 29 nc 29 nc 30 nc 30 nc 30 nc 31 nc 31 nc 31 nc 32 nc 32 GND 32 nc P0.2H P2.1/A9 nc nc N ew D nc nc nc fo r 7.7. Target Board DEBUG Interface (J9) P2.0/A8 m en de d The DEBUG connector J9 provides access to the DEBUG (C2) pins of the C8051F930. It is used to connect the Serial Adapter or the USB Debug Adapter to the target board for in-circuit debugging and Flash programming. Table 3 shows the DEBUG pin definitions. ec om Table 3. DEBUG Connector Pin Descriptions Pin # Description 1 +3 VD (+3.3 VDC) 2, 3, 9 GND (Ground) 4 P2.7/C2D 5 RST (Reset) 6 P2.7 7 RST/C2CK 8 Not Connected 10 USB Power (+5 VDC from J9) R 7.8. Serial Interface (J12) N ot A USB-to-UART bridge circuit (U3) and USB connector (P3) are provided on the target board to facilitate serial connections to UART0 of the C8051F930. The Silicon Labs CP2103 (U3) USB-to-UART bridge provides data connectivity between the C8051F930 and the PC via a USB port. The VIO power supply and TX, RX, RTS and CTS signals of UART0 may be connected to the CP2103 by installing shorting blocks on header J12. The shorting block positions for connecting each of these signals to the CP2103 are listed in Table 4. To use this interface, the USB-to-UART device drivers should be installed as described in Section 3.2. "CP210x USB to UART VCP Driver Installation‚" on page 3. Rev. 0.1 19 CP2400/1-DK Table 4. Serial Interface Header (J12) Description J12[9–10] J12[7–8] J12[5–6] J12[3–4] J12[1–2] CP2103_VIO (VDD/DC+) TX_MCU (P0.5) RX_MCU (P0.4) RTS (P0.6) CTS (P0.7) 7.9. Analog I/O (H1) es ig ns Header Pins UART0 Pin Description Pin # Description 1 2 3 4 P0.6/CNVSTR P0.7/IREF0 GND (Ground) P0.0/VREF (Voltage Reference) fo r 7.10. IREF Connector (J7) N ew Table 5. H1 Terminal Block Pin Descriptions D Several of the C8051F930 target device’s port pins are connected to the H1 terminal block. Refer to Table 5 for the H1 terminal block connections. m en de d The C8051F930 Target Board also features a current-to-voltage 1 k load resistor that may be connected to the current reference (IREF0) output that can be enabled on port pin (P0.7). Install a shorting block on J7 to connect port pin P0.7 of the target device to the load resistor. If enabled by software, the IREF0 signal is then routed to the J2[8] and H1[2] connectors. 7.11. VREF and AGND Connector (J13, J14) The C8051F930 Target Board also features 4.7 µF capacitor in parallel with a 0.1 µF that can be connected to P0.0/VREF when using the Precision Voltage Reference. The capacitors are connected to P0.0/VREF when a shorting block is installed on J13. Using the Precision Voltage Reference is optional since 'F93x-'F92x devices have an on-chip High-Speed Voltage Reference. om The shorting block J14 allows P0.1/AGND to be connected to ground. This provides a noise-free ground reference to the analog-to-digital Converter. The use of this dedicated analog ground is optional. 7.12. C2 Pin Sharing N ot R ec On the C8051F930, the debug pins C2CK and C2D are shared with the pins RST and P2.7, respectively. The target board includes the resistors necessary to enable pin sharing which allow the RST and P2.7 pins to be used normally while simultaneously debugging the device. See Application Note “AN124: Pin Sharing Techniques for the C2 Interface” at www.silabs.com for more information regarding pin sharing. 20 Rev. 0.1 CP2400/1-DK 8. CP2400/1 AB LCD Development Board es ig ns The CP2400 and CP2401 Development Kits include a CP2400 or CP2401 LCD Development Board designed to connect to C8051F9xx target boards. Various input/output (I/O) connectors are provided to facilitate prototyping using the development board. Refer to Figure 13 for the locations of the various I/O connectors. Figure 14 on page 22 shows the factory default shorting block positions. Expansion connector (96-pin) Liquid Crystal Display (LCD) CP2400/1 LCD Controller CP2400/1 Port I/O headers (provide access to Port I/O pins on CP2400/1) Creates an open in the power supply path to allow supply current measurement Provides an easily accessible ground clip Connects the LED signal from the C8051F9xx Target Board to the LED on the CP2400/1 Development Board Enable/Disable CP2400/1 Power LED LED controlled by C8051F9xx Target Board CP2400/1 Power LED D P1 DS1 U1 J1 J2 J3 J4 N ew J5 D1 D2 fo r P1 m en de d CP2400-GQ LCD DEVELOPMENT BOARD U1 CP2400 J5 IMEASURE SILICON LABS www.silabs.com D1 LED J5J4 D2 PWR Figure 13. CP2400 AB LCD Development Board N ot R ec om J1 J2 Rev. 0.1 21 CP2400/1-DK 8.1. Target Board Shorting Blocks: Factory Defaults P1 J5 IMEASURE SILICON LABS www.silabs.com D1 D2 J5J4 PWR m en de d LED fo r J1 J2 N ew U1 CP2400 D CP2400-GQ LCD DEVELOPMENT BOARD es ig ns The CP2400/1 target board comes from the factory with pre-installed shorting blocks on many headers. Figure 14 shows the positions of the factory default shorting blocks. N ot R ec om Figure 14. CP2400 AB LCD Development Board Shorting Blocks: Factory Defaults 22 Rev. 0.1 CP2400/1-DK 8.2. AB Board Current Measurement The header (J2) provides a way to measure the total supply current flowing from the power supply source to the CP2400/1. The measured current does not include any current from the LED (D1) or the Power LED (D2). See the target board schematics in Figures 15 through 18 for additional information. es ig ns 8.3. Port I/O Headers (J1, J3) Access to the CP2400/1 control interface signals (SMBus or SPI) as well as /RST, /LED, /INT, /CLK, VDD, and GND is provided through J1 on the AB board. The header J3 provides access to the ground plane for easy clipping of oscilloscope probes. 8.4. LEDs N ew D Two LEDs are provided on the AB board: one labeled “LED” and one labeled “PWR”. The PWR LED is powered by VDD being supplied to the CP2400/1. The other LED labeled “LED” is powered through from P1.7 on the C8051F930 Target Board or P2.7 on the C8051F912 Target Board. Tables 6 and 7 contain more information regarding which port pins’ control signals are connected to on the target board. Headers are provided on the AB board to allow for the LEDs to be physically disconnected from the circuit. Placing a jumper on the header J4 will connect the PWR LED to ground, which will allow it to turn on when a voltage is applied on the CP2400/1’s VDD pin. Placing a jumper on the header J5 will connect LED labeled LED to the LED signal on the attached Target Board. Tables 6 and 7 list information on which port pin on the attached Target Board is connected to the LED signal. The CP2400 LCD Development Board schematic and the CP2401 LCD Development Board schematic have more information about the LED and control signals. fo r 8.5. Target Board Connections Tables 6 and 7 list details regarding the port pin connections to the control signals on the CP2400/1. m en de d Table 6. CP2400 Control Signals F930 TB F912 TB SCK P1.0 P1.0 MISO P1.1 P1.1 MOSI P1.2 P1.2 NSS P1.3 P1.3 /INT P0.1 P0.1 /RST P0.0 P0.0 /CLK P1.4 P1.4 /LED P1.7 P2.7 N ot R ec om Signal Table 7. CP2401 Control Signals Signal F930 TB F912 TB SDA P1.0 P1.0 SCL P1.1 P1.1 /PWR P1.3 P1.3 /INT P0.1 P0.1 /RST P0.0 P0.0 /CLK P1.4 P1.4 /LED P1.7 P2.7 Rev. 0.1 23 CP2400/1-DK 8.6. Expansion I/O Connector (P1) Row A Pin # Description Row B Pin # Description Row C Pin # Description 1 +3 VD 1 GND 1 nc 2 nc 2 nc 2 3 nc 3 nc 3 4 nc 4 nc 4 5 nc 5 nc 5 6 nc 6 nc 6 nc 7 nc 7 nc 7 nc 8 nc 8 nc 8 nc 9 nc 9 nc 9 nc 10 nc 10 nc 10 nc 11 nc 11 nc 11 nc 12 nc 12 /INT_H 12 /RST_H 13 /LED_H 13 nc 13 nc m en de d Table 8. P1 Pin Descriptions nc nc D nc fo r N ew nc /CLK_H 14 NSS_H/PWR_H 14 MOSI_H 15 MISO_H/SCL_H 15 SCK_H/SDA_H 15 nc 16 nc 16 nc 16 nc nc 17 nc 17 nc nc 18 nc 18 nc nc 19 nc 19 nc nc 20 nc 20 nc nc 21 nc 21 nc 22 nc 22 nc 22 nc 23 nc 23 nc 23 nc ec 14 24 nc 24 nc 24 nc 25 nc 25 GND 25 nc 26 GND 26 nc 26 nc 27 nc 27 nc 27 nc 28 nc 28 +1.8 VD 28 nc 29 nc 29 nc 29 nc 30 nc 30 nc 30 nc 31 nc 31 nc 31 nc 32 nc 32 GND 32 nc 17 18 19 20 N ot R om 21 24 es ig ns The 96-pin Expansion I/O connector P1 provides access to all signal pins of the CP2400/1 device. In addition, power supply and ground pins are included. A small through-hole prototyping area is also provided. See Table 8 for a list of pin descriptions for P1. Rev. 0.1 N ot Rev. 0.1 fo r N ew es ig ns D Figure 15. CP2400 LCD Development Board Schematic (Page 1 of 2) m en de d om ec R CP2400/1-DK 9. Schematics 25 N ot 26 Rev. 0.1 fo r N ew es ig ns D Figure 16. CP2400 LCD Development Board Schematic (Page 2 of 2) m en de d om ec R CP2400/1-DK N ot Rev. 0.1 fo r N ew es ig ns D Figure 17. CP2401 LCD Development Board Schematic (Page 1 of 2) m en de d om ec R CP2400/1-DK 27 N ot 28 Rev. 0.1 fo r N ew es ig ns D Figure 18. CP2401 LCD Development Board Schematic (Page 2 of 2) m en de d om ec R CP2400/1-DK N ot Rev. 0.1 fo r N ew es ig ns D Figure 19. C8051F930 Target Board Schematic (Page 1 of 3) m en de d om ec R CP2400/1-DK 29 N ot 30 Rev. 0.1 fo r N ew es ig ns D Figure 20. C8051F930 Target Board Schematic (Page 2 of 3) m en de d om ec R CP2400/1-DK N ot Rev. 0.1 fo r N ew es ig ns D Figure 21. C8051F930 Target Board Schematic (Page 3 of 3) m en de d om ec R CP2400/1-DK 31 es ig ns D N ew fo r One-click access to MCU and wireless tools, documentation, software, source code libraries & more. Available for Windows, Mac and Linux! SW/HW Quality Support and Community www.silabs.com/simplicity www.silabs.com/quality community.silabs.com om IoT Portfolio www.silabs.com/IoT m en de d Simplicity Studio N ot R ec Disclaimer Silicon Labs intends to provide customers with the latest, accurate, and in-depth documentation of all peripherals and modules available for system and software implementers using or intending to use the Silicon Labs products. Characterization data, available modules and peripherals, memory sizes and memory addresses refer to each specific device, and "Typical" parameters provided can and do vary in different applications. Application examples described herein are for illustrative purposes only. Silicon Labs reserves the right to make changes without further notice and limitation to product information, specifications, and descriptions herein, and does not give warranties as to the accuracy or completeness of the included information. Silicon Labs shall have no liability for the consequences of use of the information supplied herein. This document does not imply or express copyright licenses granted hereunder to design or fabricate any integrated circuits. The products are not designed or authorized to be used within any Life Support System without the specific written consent of Silicon Labs. A "Life Support System" is any product or system intended to support or sustain life and/or health, which, if it fails, can be reasonably expected to result in significant personal injury or death. Silicon Labs products are not designed or authorized for military applications. Silicon Labs products shall under no circumstances be used in weapons of mass destruction including (but not limited to) nuclear, biological or chemical weapons, or missiles capable of delivering such weapons. Trademark Information Silicon Laboratories Inc.® , Silicon Laboratories®, Silicon Labs®, SiLabs® and the Silicon Labs logo®, Bluegiga®, Bluegiga Logo®, Clockbuilder®, CMEMS®, DSPLL®, EFM®, EFM32®, EFR, Ember®, Energy Micro, Energy Micro logo and combinations thereof, "the world’s most energy friendly microcontrollers", Ember®, EZLink®, EZRadio®, EZRadioPRO®, Gecko®, ISOmodem®, Precision32®, ProSLIC®, Simplicity Studio®, SiPHY®, Telegesis, the Telegesis Logo®, USBXpress® and others are trademarks or registered trademarks of Silicon Labs. ARM, CORTEX, Cortex-M3 and THUMB are trademarks or registered trademarks of ARM Holdings. Keil is a registered trademark of ARM Limited. All other products or brand names mentioned herein are trademarks of their respective holders. Silicon Laboratories Inc. 400 West Cesar Chavez Austin, TX 78701 USA http://www.silabs.com
CP2401DK 价格&库存

很抱歉,暂时无法提供与“CP2401DK”相匹配的价格&库存,您可以联系我们找货

免费人工找货