EFM32G200F32G-E-QFN32

EFM32 Gecko Family EFM32G Data Sheet The EFM32 Gecko MCUs are the world’s most energy-friendly microcontrollers. KEY FEATURES The EFM32G offers unmatched performance and ultra low power consumption in both active and sleep modes. EFM32G devices consume as little as 0.6 μA in Stop mode and 180 μA/MHz in Run mode. It also features autonomous peripherals, high overall chip and analog integration, and the performance of the industry standard 32-bit ARM Cortex-M3 processor, making it perfect for battery-powered systems and systems with high-performance, low-energy requirements. • Alarm and security systems • Industrial and home automation Core / Memory ARM CortexTM M3 processor Flash Program Memory RAM Memory • Ultra low power operation • 0.6 μA current in Stop (EM3), with brown-out detection and RAM retention • 45 μA/MHz in EM1 • 180 μA/MHz in Run mode (EM0) • Fast wake-up time of 2 µs EFM32G applications include the following: • Energy, gas, water and smart metering • Health and fitness applications • Smart accessories • ARM Cortex-M3 at 32 MHz Clock Management Memory Protection Unit Debug Interface DMA Controller High Frequency Crystal Oscillator High Frequency RC Oscillator Auxiliary High Freq. RC Osc. Low Frequency RC Oscillator Low Frequency Crystal Oscillator Watchdog Oscillator • Hardware cryptography (AES) • Up to 128 kB of Flash and 16 kB of RAM Energy Management Voltage Regulator Voltage Comparator Power-On Reset Brown-Out Detector Security Hardware AES 32-bit bus Peripheral Reflex System Serial Interfaces USART Low Energy UARTTM UART I2C I/O Ports External Bus Interface External Interrupts Timers and Triggers General Purpose I/O Pin Reset Timer/Counter Pulse Counter Low Energy Timer Watchdog Timer Real Time Counter Analog Interfaces ADC DAC LCD Controller Analog Comparator Lowest power mode with peripheral operational: EM0 - Active EM1 - Sleep silabs.com | Building a more connected world. EM2 – Deep Sleep EM3 - Stop EM4 - Shutoff Rev. 2.20 EFM32G Data Sheet Feature List 1. Feature List • ARM Cortex-M3 CPU platform • High Performance 32-bit processor @ up to 32 MHz • Memory Protection Unit • Wake-up Interrupt Controller • SysTick System Timer • Flexible Energy Management System • 20 nA @ 3 V Shutoff Mode • 0.6 µA @ 3 V Stop Mode, including Power-on Reset, Brown-out Detector, RAM and CPU retention • 0.9 µA @ 3 V Deep Sleep Mode, including RTC with 32.768 kHz oscillator, Power-on Reset, Brown-out Detector, RAM and CPU retention • 45 µA/MHz @ 3 V Sleep Mode • 180 µA/MHz @ 3 V Run Mode, with code executed from flash • 128/64/32 KB Flash • 16/8 KB RAM • Up to 90 General Purpose I/O pins • Configurable push-pull, open-drain, pull-up/down, input filter, drive strength • Configurable peripheral I/O locations • 16 asynchronous external interrupts • Output state retention and wake-up from Shutoff Mode • 8 Channel DMA Controller • 8 Channel Peripheral Reflex System (PRS) for autonomous inter-peripheral signaling • Hardware AES with 128/256-bit keys in 54/75 cycles • Timers/Counters • 3 × 16-bit Timer/Counter • 3×3 Compare/Capture/PWM channels • Dead-Time Insertion on TIMER0 • 16-bit Low Energy Timer • 1× 24-bit Real-Time Counter • 3× 8-bit Pulse Counter • Watchdog Timer with dedicated RC oscillator @ 50 nA • Integrated LCD Controller for up to 4×40 segments • Voltage boost, adjustable contrast and autonomous animation • External Bus Interface for up to 4x64 MB of external memory mapped space • Communication interfaces • Up to 3× Universal Synchronous/Asynchronous Receiver/ Transmitter • UART/SPI/SmartCard (ISO 7816)/IrDA/I2S • Triple buffered full/half-duplex operation • 1× Universal Asynchronous Receiver/Transmitter • 2× Low Energy UART • Autonomous operation with DMA in Deep Sleep Mode • I2C Interface with SMBus support • Address recognition in Stop Mode • Ultra low power precision analog peripherals • 12-bit 1 Msamples/s Analog to Digital Converter • 8 single-ended channels/4 differential channels • On-chip temperature sensor • 12-bit 500 ksamples/s Digital to Analog Converter • 2 single-ended channels/1 differential channel • 2× Analog Comparator • Capacitive sensing with up to 16 inputs • Supply Voltage Comparator silabs.com | Building a more connected world. Rev. 2.20 | 2 EFM32G Data Sheet Feature List • Ultra efficient Power-on Reset and Brown-Out Detector • 2-pin Serial Wire Debug Interface • 1-pin Serial Wire Viewer • Pre-Programmed UART Bootloader • Temperature range -40 to 85 ºC • Single power supply 1.98 to 3.8 V • Packages • BGA112 • LQFP100 • TQFP64 • TQFP48 • QFN64 • QFN32 silabs.com | Building a more connected world. Rev. 2.20 | 3 EFM32G Data Sheet Ordering Information 2. Ordering Information The following table shows the available EFM32G devices. Table 2.1. Ordering Information Flash (kB) RAM (kB) Max Speed (MHz) Supply Voltage (V) Temperature (ºC) Package EFM32G200F16G-E-QFN32 16 8 32 1.98 - 3.8 -40 - 85 QFN32 EFM32G200F32G-E-QFN32 32 8 32 1.98 - 3.8 -40 - 85 QFN32 EFM32G200F64G-E-QFN32 64 16 32 1.98 - 3.8 -40 - 85 QFN32 EFM32G210F128G-E-QFN32 128 16 32 1.98 - 3.8 -40 - 85 QFN32 EFM32G222F32G-E-QFP48 32 8 32 1.98 - 3.8 -40 - 85 TQFP48 EFM32G222F64G-E-QFP48 64 16 32 1.98 - 3.8 -40 - 85 TQFP48 EFM32G222F128G-E-QFP48 128 16 32 1.98 - 3.8 -40 - 85 TQFP48 EFM32G230F32G-E-QFN64 32 8 32 1.98 - 3.8 -40 - 85 QFN64 EFM32G230F64G-E-QFN64 64 16 32 1.98 - 3.8 -40 - 85 QFN64 EFM32G230F128G-E-QFN64 128 16 32 1.98 - 3.8 -40 - 85 QFN64 EFM32G232F32G-E-QFP64 32 8 32 1.98 - 3.8 -40 - 85 TQFP64 EFM32G232F64G-E-QFP64 64 16 32 1.98 - 3.8 -40 - 85 TQFP64 EFM32G232F128G-E-QFP64 128 16 32 1.98 - 3.8 -40 - 85 TQFP64 EFM32G280F32G-E-QFP100 32 8 32 1.98 - 3.8 -40 - 85 LQFP100 EFM32G280F64G-E-QFP100 64 16 32 1.98 - 3.8 -40 - 85 LQFP100 EFM32G280F128G-E-QFP100 128 16 32 1.98 - 3.8 -40 - 85 LQFP100 EFM32G290F32G-E-BGA112 32 8 32 1.98 - 3.8 -40 - 85 BGA112 EFM32G290F64G-E-BGA112 64 16 32 1.98 - 3.8 -40 - 85 BGA112 EFM32G290F128G-E-BGA112 128 16 32 1.98 - 3.8 -40 - 85 BGA112 EFM32G840F32G-E-QFN64 32 8 32 1.98 - 3.8 -40 - 85 QFN64 EFM32G840F64G-E-QFN64 64 16 32 1.98 - 3.8 -40 - 85 QFN64 EFM32G840F128G-E-QFN64 128 16 32 1.98 - 3.8 -40 - 85 QFN64 EFM32G842F32G-E-QFP64 32 8 32 1.98 - 3.8 -40 - 85 TQFP64 EFM32G842F64G-E-QFP64 64 16 32 1.98 - 3.8 -40 - 85 TQFP64 EFM32G842F128G-E-QFP64 128 16 32 1.98 - 3.8 -40 - 85 TQFP64 EFM32G880F32G-E-QFP100 32 8 32 1.98 - 3.8 -40 - 85 LQFP100 EFM32G880F64G-E-QFP100 64 16 32 1.98 - 3.8 -40 - 85 LQFP100 EFM32G880F128G-E-QFP100 128 16 32 1.98 - 3.8 -40 - 85 LQFP100 EFM32G890F32G-E-BGA112 32 8 32 1.98 - 3.8 -40 - 85 BGA112 EFM32G890F64G-E-BGA112 64 16 32 1.98 - 3.8 -40 - 85 BGA112 EFM32G890F128G-E-BGA112 128 16 32 1.98 - 3.8 -40 - 85 BGA112 Ordering Code silabs.com | Building a more connected world. Rev. 2.20 | 4 EFM32G Data Sheet Ordering Information EFM32 G 890 F 128 G – E – BGA 112 R Tape and Reel (Optional) Pin Count Package Revision Temperature Grade – G (-40 to +85 °C) Memory Size in kB Memory Type (Flash) Feature Set Code Gecko Energy Friendly Microcontroller 32-bit Figure 2.1. Ordering Code Decoder Adding the suffix 'R' to the part number (e.g., EFM32G890F128G-E-BGA112R) denotes tape and reel. Visit www.silabs.com for information on global distributors and representatives. silabs.com | Building a more connected world. Rev. 2.20 | 5 Table of Contents 1. Feature List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 2. Ordering Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 3. System Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 3.1 System Introduction . . . . . . . . . . . . . . . . . . . . 3.1.1 ARM Cortex-M3 Core . . . . . . . . . . . . . . . . . 3.1.2 Debug Interface (DBG) . . . . . . . . . . . . . . . . . 3.1.3 Memory System Controller (MSC) . . . . . . . . . . . . . 3.1.4 Direct Memory Access Controller (DMA) . . . . . . . . . . . 3.1.5 Reset Management Unit (RMU) . . . . . . . . . . . . . . 3.1.6 Energy Management Unit (EMU) . . . . . . . . . . . . . 3.1.7 Clock Management Unit (CMU) . . . . . . . . . . . . . . 3.1.8 Watchdog (WDOG) . . . . . . . . . . . . . . . . . . 3.1.9 Peripheral Reflex System (PRS) . . . . . . . . . . . . . 3.1.10 External Bus Interface (EBI) . . . . . . . . . . . . . . 3.1.11 Inter-Integrated Circuit Interface (I2C) . . . . . . . . . . . 3.1.12 Universal Synchronous/Asynchronous Receiver/Transmitter (USART) 3.1.13 Pre-Programmed USB/UART Bootloader . . . . . . . . . . 3.1.14 Universal Asynchronous Receiver/Transmitter (UART) . . . . . 3.1.15 Low Energy Universal Asynchronous Receiver/Transmitter (LEUART) 3.1.16 Timer/Counter (TIMER) . . . . . . . . . . . . . . . . 3.1.17 Real Time Counter (RTC) . . . . . . . . . . . . . . . 3.1.18 Low Energy Timer (LETIMER) . . . . . . . . . . . . . . 3.1.19 Pulse Counter (PCNT) . . . . . . . . . . . . . . . . 3.1.20 Analog Comparator (ACMP) . . . . . . . . . . . . . . 3.1.21 Voltage Comparator (VCMP) . . . . . . . . . . . . . . 3.1.22 Analog to Digital Converter (ADC) . . . . . . . . . . . . 3.1.23 Digital to Analog Converter (DAC) . . . . . . . . . . . . 3.1.24 Advanced Encryption Standard Accelerator (AES) . . . . . . . 3.1.25 General Purpose Input/Output (GPIO) . . . . . . . . . . . 3.1.26 Liquid Crystal Display Driver (LCD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10 .10 .10 .10 .11 .11 .11 .11 .11 .11 .11 .11 .11 .11 .12 .12 .12 .12 .12 .12 .12 .12 .12 .12 .13 .13 .13 3.2 Configuration Summary 3.2.1 EFM32G200 . . 3.2.2 EFM32G210 . . 3.2.3 EFM32G222 . . 3.2.4 EFM32G230 . . 3.2.5 EFM32G232 . . 3.2.6 EFM32G280 . . 3.2.7 EFM32G290 . . 3.2.8 EFM32G840 . . 3.2.9 EFM32G842 . . 3.2.10 EFM32G880 . . 3.2.11 EFM32G890 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14 .14 .15 .16 .17 .18 .19 .20 .21 .22 .23 .25 3.3 Memory Map . . . . . . . . . . . . . . . . . . . . . . . . . . .27 . . . 4. Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . 29 silabs.com | Building a more connected world. Rev. 2.20 | 6 4.1 Test Conditions . . . . . . . . 4.1.1 Typical Values . . . . . . 4.1.2 Minimum and Maximum Values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29 .29 .29 4.2 Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . .29 4.3 General Operating Conditions . . . . . . . . . . . . . . . . . . . . . . . .29 4.4 Current Consumption . . . . 4.4.1 EM0 Current Consumption 4.4.2 EM1 Current Consumption 4.4.3 EM2 Current Consumption 4.4.4 EM3 Current Consumption 4.4.5 EM4 Current Consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30 .31 .34 .37 .38 .39 4.5 Transition between Energy Modes . . . . . . . . . . . . . . . . . . . . . . .39 4.6 Power Management . . . . . . . . . . . . . . . . . . . . . . . . . . . .40 4.7 Flash . . . . . . . . . . . . . . . . . . . . . . . . . . . .41 4.8 General Purpose Input Output . . . . . . . . . . . . . . . . . . . . . . . .42 4.9 Oscillators . . . 4.9.1 LFXO. . . 4.9.2 HFXO . . 4.9.3 LFRCO . . 4.9.4 HFRCO . . 4.9.5 AUXHFRCO 4.9.6 ULFRCO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50 .50 .51 .52 .53 .57 .57 4.10 Analog Digital Converter (ADC) 4.10.1 Typical Performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58 .67 4.11 Digital Analog Converter (DAC) . . . . . . . . . . . . . . . . . . . . . . .71 4.12 Analog Comparator (ACMP) . . . . . . . . . . . . . . . . . . . . . . . .73 4.13 Voltage Comparator (VCMP) . . . . . . . . . . . . . . . . . . . . . . . .75 4.14 LCD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .76 4.15 I2C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .77 4.16 Digital Peripherals . . . . . . . . . . . . . . . . . . . . . . . . . . . .78 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5. Pin Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79 5.1 EFM32G200 & EFM32G210 (QFN32) . 5.1.1 Pinout . . . . . . . . . 5.1.2 Alternate Functionality Pinout . 5.1.3 GPIO Pinout Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79 .79 .82 .84 5.2 EFM32G222 (TQFP48). . . . . 5.2.1 Pinout . . . . . . . . 5.2.2 Alternate Functionality Pinout 5.2.3 GPIO Pinout Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .85 .85 .88 .90 5.3 EFM32G230 (QFN64) . . . . . 5.3.1 Pinout . . . . . . . . 5.3.2 Alternate Functionality Pinout 5.3.3 GPIO Pinout Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91 .91 .94 .97 silabs.com | Building a more connected world. Rev. 2.20 | 7 5.4 EFM32G232 (TQFP64). . . . . . . . . . . . . . . . . . . . . . . . . . .98 5.4.1 Pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .98 5.4.2 Alternate Functionality Pinout . . . . . . . . . . . . . . . . . . . . 101 . 5.4.3 GPIO Pinout Overview . . . . . . . . . . . . . . . . . . . . . . . . 103 5.5 EFM32G280 (LQFP100) . . . . . . . . . . . . . . . . . . . . . . . . .104 5.5.1 Pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . 04 5.5.2 Alternate Functionality Pinout . . . . . . . . . . . . . . . . . . . . 109 . 5.5.3 GPIO Pinout Overview . . . . . . . . . . . . . . . . . . . . . . . . 113 5.6 EFM32G290 (BGA112). . . . . . . . . . . . . . . . . . . . . . . . . . 114 5.6.1 Pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . 14 5.6.2 Alternate Functionality Pinout . . . . . . . . . . . . . . . . . . . . 119 . 5.6.3 GPIO Pinout Overview . . . . . . . . . . . . . . . . . . . . . . . . 123 5.7 EFM32G840 (QFN64) . . . . . . . . . . . . . . . . . . . . . . . . . . 124 5.7.1 Pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . 24 5.7.2 Alternate Functionality Pinout . . . . . . . . . . . . . . . . . . . . 127 . 5.7.3 GPIO Pinout Overview . . . . . . . . . . . . . . . . . . . . . . . . 131 5.8 EFM32G842 (TQFP64). . . . . . . . . . . . . . . . . . . . . . . . . . 132 5.8.1 Pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . 32 5.8.2 Alternate Functionality Pinout . . . . . . . . . . . . . . . . . . . . 135 . 5.8.3 GPIO Pinout Overview . . . . . . . . . . . . . . . . . . . . . . . . 139 5.9 EFM32G880 (LQFP100) . . . . . . . . . . . . . . . . . . . . . . . . .140 5.9.1 Pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . 40 5.9.2 Alternate Functionality Pinout . . . . . . . . . . . . . . . . . . . . 146 . 5.9.3 GPIO Pinout Overview . . . . . . . . . . . . . . . . . . . . . . . . 152 5.10 EFM32G890 (BGA112) . . . . . . . . . . . . . . . . . . . . . . . . .153 5.10.1 Pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 153 5.10.2 Alternate Functionality Pinout . . . . . . . . . . . . . . . . . . . . .159 5.10.3 GPIO Pinout Overview . . . . . . . . . . . . . . . . . . . . . . 1 . 65 6. BGA112 Package Specifications . . . . . . . . . . . . . . . . . . . . . . .166 6.1 BGA112 Package Dimensions 6.2 BGA112 PCB Layout . . 6.3 BGA112 Package Marking . . . . . . . . . . . . . . . . . . . . . . .166 . . . . . . . . . . . . . . . . . . . . . . . .167 . . . . . . . . . . . . . . . . . . . . . . . 169 . 7. LQFP100 Package Specifications . . . . . . . . . . . . . . . . . . . . . . . 170 7.1 LQFP100 Package Dimensions . . . . . . . . . . . . . . . . . . . . . . . 170 7.2 LQFP100 PCB Layout . . . . . . . . . . . . . . . . . . . . . . . . . . 172 7.3 LQFP100 Package Marking . . . . . . . . . . . . . . . . . . . . . . . .174 8. TQFP64 Package Specifications . . . . . . . . . . . . . . . . . . . . . . .175 8.1 TQFP64 Package Dimensions 8.2 TQFP64 PCB Layout . . 8.3 TQFP64 Package Marking 9. TQFP48 Package Specifications 9.1 TQFP48 Package Dimensions silabs.com | Building a more connected world. . . . . . . . . . . . . . . . . . . . . . . .175 . . . . . . . . . . . . . . . . . . . . . . . .177 . . . . . . . . . . . . . . . . . . . . . . . 179 . . . . . . . . . . . . . . . . . . . . . . . .180 . . . . . . . . . . . . . . . . . . . . . . .180 Rev. 2.20 | 8 9.2 TQFP48 PCB Layout . . 9.3 TQFP48 Package Marking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 184 . 10. QFN64 Package Specifications . . . . . . . . . . . . . . . . . . . . . . .185 10.1 QFN64 Package Dimensions 10.2 QFN64 PCB Layout . . 10.3 QFN64 Package Marking . . . . . . . . . . . . . . . . . . . . . . .185 . . . . . . . . . . . . . . . . . . . . . . . .187 . . . . . . . . . . . . . . . . . . . . . . . 189 . 11. QFN32 Package Specifications . . . . . . . . . . . . . . . . . . . . . . .190 11.1 QFN32 Package Dimensions 11.2 QFN32 PCB Layout . . 11.3 QFN32 Package Marking . . . . . . . . . . . . . . . . . . . . . . .190 . . . . . . . . . . . . . . . . . . . . . . . .191 . . . . . . . . . . . . . . . . . . . . . . . 193 . 12. Chip Revision, Solder Information, Errata 12.1 Chip Revision . . . 12.2 Soldering Information . 12.3 Errata . . . . . . . . . . . .182 . . . . . . . . . . . . . . . . . . . . . . . . . . . .194 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1. 94 . . . 194 . .194 13. Revision History. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 195 13.1 Revision 2.20 . . . . . . . . . . . . . . . . . . . . . . . . . . . 195 . 13.2 Revision 2.10 . . . . . . . . . . . . . . . . . . . . . . . . . . . 195 . 13.3 Revision 2.00 . . . . . . . . . . . . . . . . . . . . . . . . . . . 196 . 13.4 Revision 1.90 . . . . . . . . . . . . . . . . . . . . . . . . . . . 197 . 13.5 Revision 1.80 . . . . . . . . . . . . . . . . . . . . . . . . . . . 197 . 13.6 Revision 1.71 . . . . . . . . . . . . . . . . . . . . . . . . . . . 198 . 13.7 Revision 1.70 . . . . . . . . . . . . . . . . . . . . . . . . . . . 198 . 13.8 Revision 1.60 . . . . . . . . . . . . . . . . . . . . . . . . . . . 198 . 13.9 Revision 1.50 . . . . . . . . . . . . . . . . . . . . . . . . . . . 198 . 13.10 Revision 1.40 . . . . . . . . . . . . . . . . . . . . . . . . . . . .199 13.11 Revision 1.30 . . . . . . . . . . . . . . . . . . . . . . . . . . . .199 13.12 Revision 1.20 . . . . . . . . . . . . . . . . . . . . . . . . . . . .200 13.13 Revision 1.11 . . . . . . . . . . . . . . . . . . . . . . . . . . . .200 13.14 Revision 1.10 . . . . . . . . . . . . . . . . . . . . . . . . . . . .201 13.15 Revision 1.00 . . . . . . . . . . . . . . . . . . . . . . . . . . . .201 13.16 Revision 0.90 . . . . . . . . . . . . . . . . . . . . . . . . . . . .202 13.17 Revision 0.85 . . . . . . . . . . . . . . . . . . . . . . . . . . . .202 13.18 Revision 0.84 . . . . . . . . . . . . . . . . . . . . . . . . . . . .202 13.19 Revision 0.83 . . . . . . . . . . . . . . . . . . . . . . . . . . . .202 13.20 Revision 0.82 . . . . . . . . . . . . . . . . . . . . . . . . . . . .203 13.21 Revision 0.81 . . . . . . . . . . . . . . . . . . . . . . . . . . . .203 13.22 Revision 0.80 . . . . . . . . . . . . . . . . . . . . . . . . . . . .204 silabs.com | Building a more connected world. Rev. 2.20 | 9 EFM32G Data Sheet System Overview 3. System Overview 3.1 System Introduction EFM32 MCUs are the world’s most energy friendly microcontrollers. With a unique combination of the powerful 32-bit ARM Cortex-M3, innovative low energy techniques, short wake-up time from energy saving modes, and a wide selection of peripherals, the EFM32G microcontroller is well suited for any battery operated application as well as other systems requiring high performance and low-energy consumption. This section gives a short introduction to each of the modules in general terms and also shows a summary of the configuration for the EFM32G devices. For a complete feature set and in-depth information on the modules, the reader is referred to the EFM32G Reference Manual. The diagram shows a superset of features available on the family, which vary by OPN. For more information about specific device features, consult Ordering Information. Core / Memory ARM CortexTM M3 processor Memory Protection Unit Flash Program Memory Debug Interface RAM Memory DMA Controller Clock Management High Frequency Crystal Oscillator High Frequency RC Oscillator Auxiliary High Freq. RC Osc. Low Frequency RC Oscillator Low Frequency Crystal Oscillator Watchdog Oscillator Energy Management Voltage Regulator Voltage Comparator Power-On Reset Brown-Out Detector Security Hardware AES 32-bit bus Peripheral Reflex System Serial Interfaces USART Low Energy UARTTM UART I2C I/O Ports External Bus Interface External Interrupts Timers and Triggers General Purpose I/O Pin Reset Timer/Counter Pulse Counter Low Energy Timer Watchdog Timer Real Time Counter Analog Interfaces ADC DAC LCD Controller Analog Comparator Lowest power mode with peripheral operational: EM0 - Active EM1 - Sleep EM2 – Deep Sleep EM3 - Stop EM4 - Shutoff Figure 3.1. Block Diagram 3.1.1 ARM Cortex-M3 Core The ARM Cortex-M3 includes a 32-bit RISC processor which can achieve as much as 1.25 Dhrystone MIPS/MHz. A Memory Protection Unit with support for up to 8 memory segments is included, as well as a Wake-up Interrupt Controller handling interrupts triggered while the CPU is asleep. The EFM32 implementation of the Cortex-M3 is described in detail in EFM32G Reference Manual. 3.1.2 Debug Interface (DBG) This device includes hardware debug support through a 2-pin serial-wire debug interface . In addition there is also a 1-wire Serial Wire Viewer pin which can be used to output profiling information, data trace and software-generated messages. 3.1.3 Memory System Controller (MSC) The Memory System Controller (MSC) is the program memory unit of the EFM32G microcontroller. The flash memory is readable and writable from both the Cortex-M3 and DMA. The flash memory is divided into two blocks; the main block and the information block. Program code is normally written to the main block. Additionally, the information block is available for special user data and flash lock bits. There is also a read-only page in the information block containing system and device calibration data. Read and write operations are supported in the energy modes EM0 and EM1. silabs.com | Building a more connected world. Rev. 2.20 | 10 EFM32G Data Sheet System Overview 3.1.4 Direct Memory Access Controller (DMA) The Direct Memory Access (DMA) controller performs memory operations independently of the CPU. This has the benefit of reducing the energy consumption and the workload of the CPU, and enables the system to stay in low energy modes when moving for instance data from the USART to RAM or from the External Bus Interface to a PWM-generating timer. The DMA controller uses the PL230 µDMA controller licensed from ARM. 3.1.5 Reset Management Unit (RMU) The RMU is responsible for handling the reset functionality of the EFM32G. 3.1.6 Energy Management Unit (EMU) The Energy Management Unit (EMU) manages all the low energy modes (EM) in EFM32G microcontrollers. Each energy mode manages if the CPU and the various peripherals are available. The EMU can also be used to turn off the power to unused SRAM blocks. 3.1.7 Clock Management Unit (CMU) The Clock Management Unit (CMU) is responsible for controlling the oscillators and clocks on-board the EFM32G. The CMU provides the capability to turn on and off the clock on an individual basis to all peripheral modules in addition to enable/disable and configure the available oscillators. The high degree of flexibility enables software to minimize energy consumption in any specific application by not wasting power on peripherals and oscillators that are inactive. 3.1.8 Watchdog (WDOG) The purpose of the watchdog timer is to generate a reset in case of a system failure, to increase application reliability. The failure may e.g. be caused by an external event, such as an ESD pulse, or by a software failure. 3.1.9 Peripheral Reflex System (PRS) The Peripheral Reflex System (PRS) system is a network which lets the different peripheral module communicate directly with each other without involving the CPU. Peripheral modules which send out Reflex signals are called producers. The PRS routes these reflex signals to consumer peripherals which apply actions depending on the data received. The format for the Reflex signals is not given, but edge triggers and other functionality can be applied by the PRS. 3.1.10 External Bus Interface (EBI) The External Bus Interface provides access to external parallel interface devices such as SRAM, FLASH, ADCs and LCDs. The interface is memory mapped into the address bus of the Cortex-M3. This enables seamless access from software without manually manipulating the IO settings each time a read or write is performed. The data and address lines are multiplexed in order to reduce the number of pins required to interface the external devices. The timing is adjustable to meet specifications of the external devices. The interface is limited to asynchronous devices. 3.1.11 Inter-Integrated Circuit Interface (I2C) The I2C module provides an interface between the MCU and a serial I2C-bus. It is capable of acting as both a master and a slave, and supports multi-master buses. Both standard-mode, fast-mode and fastmode plus speeds are supported, allowing transmission rates all the way from 10 kbit/s up to 1 Mbit/s. Slave arbitration and timeouts are also provided to allow implementation of an SMBus compliant system. The interface provided to software by the I2C module, allows both fine-grained control of the transmission process and close to automatic transfers. Automatic recognition of slave addresses is provided in all energy modes. 3.1.12 Universal Synchronous/Asynchronous Receiver/Transmitter (USART) The Universal Synchronous Asynchronous serial Receiver and Transmitter (USART) is a very flexible serial I/O module. It supports full duplex asynchronous UART communication as well as RS-485, SPI, MicroWire and 3-wire. It can also interface with ISO7816 SmartCards, and IrDA devices. 3.1.13 Pre-Programmed USB/UART Bootloader The bootloader presented in application note AN0003.0 is pre-programmed in the device at factory. Autobaud and destructive write are supported. The autobaud feature, interface and commands are described further in the application note. silabs.com | Building a more connected world. Rev. 2.20 | 11 EFM32G Data Sheet System Overview 3.1.14 Universal Asynchronous Receiver/Transmitter (UART) The Universal Asynchronous serial Receiver and Transmitter (UART) is a very flexible serial I/O module. It supports full- and half-duplex asynchronous UART communication. 3.1.15 Low Energy Universal Asynchronous Receiver/Transmitter (LEUART) The unique LEUARTTM, the Low Energy UART, is a UART that allows two-way UART communication on a strict power budget. Only a 32.768 kHz clock is needed to allow UART communication up to 9600 baud/ s. The LEUART includes all necessary hardware support to make asynchronous serial communication possible with minimum of software intervention and energy consumption. 3.1.16 Timer/Counter (TIMER) The 16-bit general purpose Timer has 3 compare/capture channels for input capture and compare/Pulse-Width Modulation (PWM) output. TIMER0 also includes a Dead-Time Insertion module suitable for motor control applications. 3.1.17 Real Time Counter (RTC) The Real Time Counter (RTC) contains a 24-bit counter and is clocked either by a 32.768 kHz crystal oscillator, or a 32.768 kHz RC oscillator. In addition to energy modes EM0 and EM1, the RTC is also available in EM2. This makes it ideal for keeping track of time since the RTC is enabled in EM2 where most of the device is powered down. 3.1.18 Low Energy Timer (LETIMER) The unique LETIMERTM, the Low Energy Timer, is a 16-bit timer that is available in energy mode EM2 in addition to EM1 and EM0. Because of this, it can be used for timing and output generation when most of the device is powered down, allowing simple tasks to be performed while the power consumption of the system is kept at an absolute minimum. The LETIMER can be used to output a variety of waveforms with minimal software intervention. It is also connected to the Real Time Counter (RTC), and can be configured to start counting on compare matches from the RTC. 3.1.19 Pulse Counter (PCNT) The Pulse Counter (PCNT) can be used for counting pulses on a single input or to decode quadrature encoded inputs. It runs off either the internal LFACLK or the PCNTn_S0IN pin as external clock source. The module may operate in energy mode EM0 - EM3. 3.1.20 Analog Comparator (ACMP) The Analog Comparator is used to compare the voltage of two analog inputs, with a digital output indicating which input voltage is higher. Inputs can either be one of the selectable internal references or from external pins. Response time and thereby also the current consumption can be configured by altering the current supply to the comparator. 3.1.21 Voltage Comparator (VCMP) The Voltage Supply Comparator is used to monitor the supply voltage from software. An interrupt can be generated when the supply falls below or rises above a programmable threshold. Response time and thereby also the current consumption can be configured by altering the current supply to the comparator. 3.1.22 Analog to Digital Converter (ADC) The ADC is a Successive Approximation Register (SAR) architecture, with a resolution of up to 12 bits at up to one million samples per second. The integrated input mux can select inputs from 8 external pins and 6 internal signals. 3.1.23 Digital to Analog Converter (DAC) The Digital to Analog Converter (DAC) can convert a digital value to an analog output voltage. The DAC is fully differential rail-to-rail, with 12-bit resolution. It has two single-ended output buffers which can be combined into one differential output. The DAC may be used for a number of different applications such as sensor interfaces or sound output. silabs.com | Building a more connected world. Rev. 2.20 | 12 EFM32G Data Sheet System Overview 3.1.24 Advanced Encryption Standard Accelerator (AES) The AES accelerator performs AES encryption and decryption with 128-bit or 256-bit keys. Encrypting or decrypting one 128-bit data block takes 52 HFCORECLK cycles with 128-bit keys and 75 HFCORECLK cycles with 256-bit keys. The AES module is an AHB slave which enables efficient access to the data and key registers. All write accesses to the AES module must be 32-bit operations, i.e. 8- or 16-bit operations are not supported. 3.1.25 General Purpose Input/Output (GPIO) General Purpose Input/Output (GPIO) pins are organized into ports with up to 16 pins each. These pins can individually be configured as either an output or input. More advanced configurations like open-drain, filtering and drive strength can also be configured individually for the pins. The GPIO pins can also be overridden by peripheral pin connections, like Timer PWM outputs or USART communication, which can be routed to several locations on the device. The GPIO supports up to 16 asynchronous external pin interrupts, which enables interrupts from any pin on the device. Also, the input value of a pin can be routed through the Peripheral Reflex System to other peripherals. 3.1.26 Liquid Crystal Display Driver (LCD) The LCD driver is capable of driving a segmented LCD display with up to 4x40 segments. A voltage boost function enables it to provide the LCD display with higher voltage than the supply voltage for the device. In addition, an animation feature can run custom animations on the LCD display without any CPU intervention. The LCD driver can also remain active even in Energy Mode 2 and provides a Frame Counter interrupt that can wake-up the device on a regular basis for updating data. silabs.com | Building a more connected world. Rev. 2.20 | 13 EFM32G Data Sheet System Overview 3.2 Configuration Summary 3.2.1 EFM32G200 The features of the EFM32G200 is a subset of the feature set described in the EFM32G Reference Manual. The following table describes device specific implementation of the features. Table 3.1. EFM32G200 Configuration Summary Module Configuration Pin Connections Cortex-M3 Full configuration NA DBG Full configuration DBG_SWCLK, DBG_SWDIO, DBG_SWO MSC Full configuration NA DMA Full configuration NA RMU Full configuration NA EMU Full configuration NA CMU Full configuration CMU_OUT0, CMU_OUT1 WDOG Full configuration NA PRS Full configuration NA I2C0 Full configuration I2C0_SDA, I2C0_SCL USART0 Full configuration with IrDA US0_TX, US0_RX. US0_CLK, US0_CS USART1 Full configuration US1_TX, US1_RX, US1_CLK, US1_CS LEUART0 Full configuration LEU0_TX, LEU0_RX TIMER0 Full configuration with DTI TIM0_CC[2:0], TIM0_CDTI[2:0] TIMER1 Full configuration TIM1_CC[2:0] RTC Full configuration NA LETIMER0 Full configuration LET0_O[1:0] PCNT0 Full configuration, 8-bit count register PCNT0_S[1:0] ACMP0 Full configuration ACMP0_CH[1:0], ACMP0_O ACMP1 Full configuration ACMP1_CH[7:5], ACMP1_O VCMP Full configuration NA ADC0 Full configuration ADC0_CH[7:4] DAC0 Full configuration DAC0_OUT[0] GPIO 24 pins Available pins are shown in Table 4.3 (p. 57) silabs.com | Building a more connected world. Rev. 2.20 | 14 EFM32G Data Sheet System Overview 3.2.2 EFM32G210 The features of the EFM32G210 is a subset of the feature set described in the EFM32G Reference Manual. The following table describes device specific implementation of the features. Table 3.2. EFM32G210 Configuration Summary Module Configuration Pin Connections Cortex-M3 Full configuration NA DBG Full configuration DBG_SWCLK, DBG_SWDIO, DBG_SWO MSC Full configuration NA DMA Full configuration NA RMU Full configuration NA EMU Full configuration NA CMU Full configuration CMU_OUT0, CMU_OUT1 WDOG Full configuration NA PRS Full configuration NA I2C0 Full configuration I2C0_SDA, I2C0_SCL USART0 Full configuration with IrDA US0_TX, US0_RX. US0_CLK, US0_CS USART1 Full configuration US1_TX, US1_RX, US1_CLK, US1_CS LEUART0 Full configuration LEU0_TX, LEU0_RX TIMER0 Full configuration with DTI TIM0_CC[2:0], TIM0_CDTI[2:0] TIMER1 Full configuration TIM1_CC[2:0] RTC Full configuration NA LETIMER0 Full configuration LET0_O[1:0] PCNT0 Full configuration, 8-bit count register PCNT0_S[1:0] ACMP0 Full configuration ACMP0_CH[1:0], ACMP0_O ACMP1 Full configuration ACMP1_CH[7:5], ACMP1_O VCMP Full configuration NA ADC0 Full configuration ADC0_CH[7:4] DAC0 Full configuration DAC0_OUT[0] AES Full configuration NA GPIO 24 pins Available pins are shown in Table 4.3 (p. 57) silabs.com | Building a more connected world. Rev. 2.20 | 15 EFM32G Data Sheet System Overview 3.2.3 EFM32G222 The features of the EFM32G222 is a subset of the feature set described in the EFM32G Reference Manual. The following table describes device specific implementation of the features. Table 3.3. EFM32G222 Configuration Summary Module Configuration Pin Connections Cortex-M3 Full configuration NA DBG Full configuration DBG_SWCLK, DBG_SWDIO, DBG_SWO MSC Full configuration NA DMA Full configuration NA RMU Full configuration NA EMU Full configuration NA CMU Full configuration CMU_OUT0, CMU_OUT1 WDOG Full configuration NA PRS Full configuration NA I2C0 Full configuration I2C0_SDA, I2C0_SCL USART0 Full configuration with IrDA US0_TX, US0_RX. US0_CLK, US0_CS USART1 Full configuration US1_TX, US1_RX, US1_CLK, US1_CS LEUART0 Full configuration LEU0_TX, LEU0_RX TIMER0 Full configuration with DTI TIM0_CC[2:0], TIM0_CDTI[2:0] TIMER1 Full configuration TIM1_CC[2:0] TIMER2 Full configuration TIM2_CC[2:0] RTC Full configuration NA LETIMER0 Full configuration LET0_O[1:0] PCNT0 Full configuration, 8-bit count register PCNT0_S[1:0] PCNT1 Full configuration, 8-bit count register PCNT1_S[1:0] ACMP0 Full configuration ACMP0_CH[4:0], ACMP0_O ACMP1 Full configuration ACMP1_CH[7:0], ACMP1_O VCMP Full configuration NA ADC0 Full configuration ADC0_CH[7:4] DAC0 Full configuration DAC0_OUT[1] AES Full configuration NA GPIO 37 pins Available pins are shown in Table 4.3 (p. 57) silabs.com | Building a more connected world. Rev. 2.20 | 16 EFM32G Data Sheet System Overview 3.2.4 EFM32G230 The features of the EFM32G230 is a subset of the feature set described in the EFM32G Reference Manual. The following table describes device specific implementation of the features. Table 3.4. EFM32G230 Configuration Summary Module Configuration Pin Connections Cortex-M3 Full configuration NA DBG Full configuration DBG_SWCLK, DBG_SWDIO, DBG_SWO MSC Full configuration NA DMA Full configuration NA RMU Full configuration NA EMU Full configuration NA CMU Full configuration CMU_OUT0, CMU_OUT1 WDOG Full configuration NA PRS Full configuration NA I2C0 Full configuration I2C0_SDA, I2C0_SCL USART0 Full configuration with IrDA US0_TX, US0_RX. US0_CLK, US0_CS USART1 Full configuration US1_TX, US1_RX, US1_CLK, US1_CS USART2 Full configuration US2_TX, US2_RX, US2_CLK, US2_CS LEUART0 Full configuration LEU0_TX, LEU0_RX LEUART1 Full configuration LEU1_TX, LEU1_RX TIMER0 Full configuration with DTI TIM0_CC[2:0], TIM0_CDTI[2:0] TIMER1 Full configuration TIM1_CC[2:0] TIMER2 Full configuration TIM2_CC[2:0] RTC Full configuration NA LETIMER0 Full configuration LET0_O[1:0] PCNT0 Full configuration, 8-bit count register PCNT0_S[1:0] PCNT1 Full configuration, 8-bit count register PCNT1_S[1:0] PCNT2 Full configuration, 8-bit count register PCNT2_S[1:0] ACMP0 Full configuration ACMP0_CH[7:0], ACMP0_O ACMP1 Full configuration ACMP1_CH[7:0], ACMP1_O VCMP Full configuration NA ADC0 Full configuration ADC0_CH[7:0] DAC0 Full configuration DAC0_OUT[1:0] AES Full configuration NA GPIO 56 pins Available pins are shown in Table 4.3 (p. 57) silabs.com | Building a more connected world. Rev. 2.20 | 17 EFM32G Data Sheet System Overview 3.2.5 EFM32G232 The features of the EFM32G232 is a subset of the feature set described in the EFM32G Reference Manual. The following table describes device specific implementation of the features. Table 3.5. EFM32G232 Configuration Summary Module Configuration Pin Connections Cortex-M3 Full configuration NA DBG Full configuration DBG_SWCLK, DBG_SWDIO, DBG_SWO MSC Full configuration NA DMA Full configuration NA RMU Full configuration NA EMU Full configuration NA CMU Full configuration CMU_OUT0, CMU_OUT1 WDOG Full configuration NA PRS Full configuration NA I2C0 Full configuration I2C0_SDA, I2C0_SCL USART0 Full configuration with IrDA US0_TX, US0_RX. US0_CLK, US0_CS USART1 Full configuration US1_TX, US1_RX, US1_CLK, US1_CS USART2 Full configuration US2_TX, US2_RX, US2_CLK, US2_CS LEUART0 Full configuration LEU0_TX, LEU0_RX LEUART1 Full configuration LEU1_TX, LEU1_RX TIMER0 Full configuration with DTI TIM0_CC[2:0], TIM0_CDTI[2:0] TIMER1 Full configuration TIM1_CC[2:0] TIMER2 Full configuration TIM2_CC[2:0] RTC Full configuration NA LETIMER0 Full configuration LET0_O[1:0] PCNT0 Full configuration, 8-bit count register PCNT0_S[1:0] PCNT1 Full configuration, 8-bit count register PCNT1_S[1:0] PCNT2 Full configuration, 8-bit count register PCNT2_S[1:0] ACMP0 Full configuration ACMP0_CH[7:0], ACMP0_O ACMP1 Full configuration ACMP1_CH[15:8], ACMP1_O VCMP Full configuration NA ADC0 Full configuration ADC0_CH[7:0] DAC0 Full configuration DAC0_OUT[0] AES Full configuration NA GPIO 53 pins Available pins are shown in Table 4.3 (p. 57) silabs.com | Building a more connected world. Rev. 2.20 | 18 EFM32G Data Sheet System Overview 3.2.6 EFM32G280 The features of the EFM32G280 is a subset of the feature set described in the EFM32G Reference Manual. The following table describes device specific implementation of the features. Table 3.6. EFM32G280 Configuration Summary Module Configuration Pin Connections Cortex-M3 Full configuration NA DBG Full configuration DBG_SWCLK, DBG_SWDIO, DBG_SWO MSC Full configuration NA DMA Full configuration NA RMU Full configuration NA EMU Full configuration NA CMU Full configuration CMU_OUT0, CMU_OUT1 WDOG Full configuration NA PRS Full configuration NA EBI Full configuration EBI_ARDY, EBI_ALE, EBI_WEn, EBI_REn, EBI_CS[3:0], EBI_AD[15:0] I2C0 Full configuration I2C0_SDA, I2C0_SCL USART0 Full configuration with IrDA US0_TX, US0_RX. US0_CLK, US0_CS USART1 Full configuration US1_TX, US1_RX, US1_CLK, US1_CS USART2 Full configuration US2_TX, US2_RX, US2_CLK, US2_CS UART0 Full configuration U0_TX, U0_RX LEUART0 Full configuration LEU0_TX, LEU0_RX LEUART1 Full configuration LEU1_TX, LEU1_RX TIMER0 Full configuration with DTI TIM0_CC[2:0], TIM0_CDTI[2:0] TIMER1 Full configuration TIM1_CC[2:0] TIMER2 Full configuration TIM2_CC[2:0] RTC Full configuration NA LETIMER0 Full configuration LET0_O[1:0] PCNT0 Full configuration, 8-bit count register PCNT0_S[1:0] PCNT1 Full configuration, 8-bit count register PCNT1_S[1:0] PCNT2 Full configuration, 8-bit count register PCNT2_S[1:0] ACMP0 Full configuration ACMP0_CH[7:0], ACMP0_O ACMP1 Full configuration ACMP1_CH[7:0], ACMP1_O VCMP Full configuration NA ADC0 Full configuration ADC0_CH[7:0] DAC0 Full configuration DAC0_OUT[1:0] AES Full configuration NA GPIO 86 pins Available pins are shown in Table 4.3 (p. 57) silabs.com | Building a more connected world. Rev. 2.20 | 19 EFM32G Data Sheet System Overview 3.2.7 EFM32G290 The features of the EFM32G290 is a subset of the feature set described in the EFM32G Reference Manual. The following table describes device specific implementation of the features. Table 3.7. EFM32G290 Configuration Summary Module Configuration Pin Connections Cortex-M3 Full configuration NA DBG Full configuration DBG_SWCLK, DBG_SWDIO, DBG_SWO MSC Full configuration NA DMA Full configuration NA RMU Full configuration NA EMU Full configuration NA CMU Full configuration CMU_OUT0, CMU_OUT1 WDOG Full configuration NA PRS Full configuration NA EBI Full configuration EBI_ARDY, EBI_ALE, EBI_WEn, EBI_REn, EBI_CS[3:0], EBI_AD[15:0] I2C0 Full configuration I2C0_SDA, I2C0_SCL USART0 Full configuration with IrDA US0_TX, US0_RX. US0_CLK, US0_CS USART1 Full configuration US1_TX, US1_RX, US1_CLK, US1_CS USART2 Full configuration US2_TX, US2_RX, US2_CLK, US2_CS UART0 Full configuration U0_TX, U0_RX LEUART0 Full configuration LEU0_TX, LEU0_RX LEUART1 Full configuration LEU1_TX, LEU1_RX TIMER0 Full configuration with DTI TIM0_CC[2:0], TIM0_CDTI[2:0] TIMER1 Full configuration TIM1_CC[2:0] TIMER2 Full configuration TIM2_CC[2:0] RTC Full configuration NA LETIMER0 Full configuration LET0_O[1:0] PCNT0 Full configuration, 8-bit count register PCNT0_S[1:0] PCNT1 Full configuration, 8-bit count register PCNT1_S[1:0] PCNT2 Full configuration, 8-bit count register PCNT2_S[1:0] ACMP0 Full configuration ACMP0_CH[7:0], ACMP0_O ACMP1 Full configuration ACMP1_CH[7:0], ACMP1_O VCMP Full configuration NA ADC0 Full configuration ADC0_CH[7:0] DAC0 Full configuration DAC0_OUT[1:0] AES Full configuration NA GPIO 90 pins Available pins are shown in Table 4.3 (p. 57) silabs.com | Building a more connected world. Rev. 2.20 | 20 EFM32G Data Sheet System Overview 3.2.8 EFM32G840 The features of the EFM32G840 is a subset of the feature set described in the EFM32G Reference Manual. The following table describes device specific implementation of the features. Table 3.8. EFM32G840 Configuration Summary Module Configuration Pin Connections Cortex-M3 Full configuration NA DBG Full configuration DBG_SWCLK, DBG_SWDIO, DBG_SWO MSC Full configuration NA DMA Full configuration NA RMU Full configuration NA EMU Full configuration NA CMU Full configuration CMU_OUT0, CMU_OUT1 WDOG Full configuration NA PRS Full configuration NA I2C0 Full configuration I2C0_SDA, I2C0_SCL USART0 Full configuration with IrDA US0_TX, US0_RX. US0_CLK, US0_CS USART1 Full configuration US1_TX, US1_RX, US1_CLK, US1_CS USART2 Full configuration US2_TX, US2_RX, US2_CLK, US2_CS LEUART0 Full configuration LEU0_TX, LEU0_RX LEUART1 Full configuration LEU1_TX, LEU1_RX TIMER0 Full configuration with DTI TIM0_CC[2:0], TIM0_CDTI[2:0] TIMER1 Full configuration TIM1_CC[2:0] TIMER2 Full configuration TIM2_CC[2:0] RTC Full configuration NA LETIMER0 Full configuration LET0_O[1:0] PCNT0 Full configuration, 8-bit count register PCNT0_S[1:0] PCNT1 Full configuration, 8-bit count register PCNT1_S[1:0] PCNT2 Full configuration, 8-bit count register PCNT2_S[1:0] ACMP0 Full configuration ACMP0_CH[7:4], ACMP0_O ACMP1 Full configuration ACMP1_CH[7:4], ACMP1_O VCMP Full configuration NA ADC0 Full configuration ADC0_CH[7:0] DAC0 Full configuration DAC0_OUT[1:0] AES Full configuration NA GPIO 56 pins Available pins are shown in Table 4.3 (p. 57) LCD Full configuration LCD_SEG[23:0], LCD_COM[3:0], LCD_BCAP_P, LCD_BCAP_N, LCD_BEXT silabs.com | Building a more connected world. Rev. 2.20 | 21 EFM32G Data Sheet System Overview 3.2.9 EFM32G842 The features of the EFM32G842 is a subset of the feature set described in the EFM32G Reference Manual. The following table describes device specific implementation of the features. Table 3.9. EFM32G842 Configuration Summary Module Configuration Pin Connections Cortex-M3 Full configuration NA DBG Full configuration DBG_SWCLK, DBG_SWDIO, DBG_SWO MSC Full configuration NA DMA Full configuration NA RMU Full configuration NA EMU Full configuration NA CMU Full configuration CMU_OUT0, CMU_OUT1 WDOG Full configuration NA PRS Full configuration NA I2C0 Full configuration I2C0_SDA, I2C0_SCL USART0 Full configuration with IrDA US0_TX, US0_RX. US0_CLK, US0_CS USART1 Full configuration US1_TX, US1_RX, US1_CLK, US1_CS USART2 Full configuration US2_TX, US2_RX, US2_CLK, US2_CS LEUART0 Full configuration LEU0_TX, LEU0_RX LEUART1 Full configuration LEU1_TX, LEU1_RX TIMER0 Full configuration with DTI TIM0_CC[2:0], TIM0_CDTI[2:0] TIMER1 Full configuration TIM1_CC[2:0] TIMER2 Full configuration TIM2_CC[2:0] RTC Full configuration NA LETIMER0 Full configuration LET0_O[1:0] PCNT0 Full configuration, 8-bit count register PCNT0_S[1:0] PCNT1 Full configuration, 8-bit count register PCNT1_S[1:0] PCNT2 Full configuration, 8-bit count register PCNT2_S[1:0] ACMP0 Full configuration ACMP0_CH[3:0], ACMP0_O ACMP1 Full configuration ACMP1_CH[7:4], ACMP1_O VCMP Full configuration NA ADC0 Full configuration ADC0_CH[7:0] DAC0 Full configuration DAC0_OUT[0] AES Full configuration NA GPIO 53 pins Available pins are shown in Table 4.3 (p. 57) silabs.com | Building a more connected world. Rev. 2.20 | 22 EFM32G Data Sheet System Overview 3.2.10 EFM32G880 The features of the EFM32G880 is a subset of the feature set described in the EFM32G Reference Manual. The following table describes device specific implementation of the features. Table 3.10. EFM32G880 Configuration Summary Module Module Module Cortex-M3 Full configuration NA DBG Full configuration DBG_SWCLK, DBG_SWDIO, DBG_SWO MSC Full configuration NA DMA Full configuration NA RMU Full configuration NA EMU Full configuration NA CMU Full configuration CMU_OUT0, CMU_OUT1 WDOG Full configuration NA PRS Full configuration NA EBI Full configuration EBI_ARDY, EBI_ALE, EBI_WEn, EBI_REn, EBI_CS[3:0], EBI_AD[15:0] I2C0 Full configuration I2C0_SDA, I2C0_SCL USART0 Full configuration with IrDA US0_TX, US0_RX. US0_CLK, US0_CS USART1 Full configuration US1_TX, US1_RX, US1_CLK, US1_CS USART2 Full configuration US2_TX, US2_RX, US2_CLK, US2_CS UART0 Full configuration U0_TX, U0_RX LEUART0 Full configuration LEU0_TX, LEU0_RX LEUART1 Full configuration LEU1_TX, LEU1_RX TIMER0 Full configuration with DTI TIM0_CC[2:0], TIM0_CDTI[2:0] TIMER1 Full configuration TIM1_CC[2:0] TIMER2 Full configuration TIM2_CC[2:0] RTC Full configuration NA LETIMER0 Full configuration LET0_O[1:0] PCNT0 Full configuration, 8-bit count register PCNT0_S[1:0] PCNT1 Full configuration, 8-bit count register PCNT1_S[1:0] PCNT2 Full configuration, 8-bit count register PCNT2_S[1:0] ACMP0 Full configuration ACMP0_CH[7:0], ACMP0_O ACMP1 Full configuration ACMP1_CH[7:0], ACMP1_O VCMP Full configuration NA ADC0 Full configuration ADC0_CH[7:0] DAC0 Full configuration DAC0_OUT[1:0] AES Full configuration NA GPIO 86 pins Available pins are shown in Table 4.3 (p. 57) silabs.com | Building a more connected world. Rev. 2.20 | 23 EFM32G Data Sheet System Overview Module Module Module LCD Full configuration LCD_SEG[39:0], LCD_COM[3:0], LCD_BCAP_P, LCD_BCAP_N, LCD_BEXT silabs.com | Building a more connected world. Rev. 2.20 | 24 EFM32G Data Sheet System Overview 3.2.11 EFM32G890 The features of the EFM32G890 is a subset of the feature set described in the EFM32G Reference Manual. The following table describes device specific implementation of the features. Table 3.11. EFM32G890 Configuration Summary Module Configuration Pin Connections Cortex-M3 Full configuration NA DBG Full configuration DBG_SWCLK, DBG_SWDIO, DBG_SWO MSC Full configuration NA DMA Full configuration NA RMU Full configuration NA EMU Full configuration NA CMU Full configuration CMU_OUT0, CMU_OUT1 WDOG Full configuration NA PRS Full configuration NA EBI Full configuration EBI_ARDY, EBI_ALE, EBI_WEn, EBI_REn, EBI_CS[3:0], EBI_AD[15:0] I2C0 Full configuration I2C0_SDA, I2C0_SCL USART0 Full configuration with IrDA US0_TX, US0_RX. US0_CLK, US0_CS USART1 Full configuration US1_TX, US1_RX, US1_CLK, US1_CS USART2 Full configuration US2_TX, US2_RX, US2_CLK, US2_CS UART0 Full configuration U0_TX, U0_RX LEUART0 Full configuration LEU0_TX, LEU0_RX LEUART1 Full configuration LEU1_TX, LEU1_RX TIMER0 Full configuration with DTI TIM0_CC[2:0], TIM0_CDTI[2:0] TIMER1 Full configuration TIM1_CC[2:0] TIMER2 Full configuration TIM2_CC[2:0] RTC Full configuration NA LETIMER0 Full configuration LET0_O[1:0] PCNT0 Full configuration, 8-bit count register PCNT0_S[1:0] PCNT1 Full configuration, 8-bit count register PCNT1_S[1:0] PCNT2 Full configuration, 8-bit count register PCNT2_S[1:0] ACMP0 Full configuration ACMP0_CH[7:0], ACMP0_O ACMP1 Full configuration ACMP1_CH[7:0], ACMP1_O VCMP Full configuration NA ADC0 Full configuration ADC0_CH[7:0] DAC0 Full configuration DAC0_OUT[1:0] AES Full configuration NA GPIO 90 pins Available pins are shown in Table 4.3 (p. 57) silabs.com | Building a more connected world. Rev. 2.20 | 25 EFM32G Data Sheet System Overview Module Configuration Pin Connections LCD Full configuration LCD_SEG[39:0], LCD_COM[7:0], LCD_BCAP_P, LCD_BCAP_N, LCD_BEXT silabs.com | Building a more connected world. Rev. 2.20 | 26 EFM32G Data Sheet System Overview 3.3 Memory Map The EFM32G memory map is shown in the figure below. RAM and Flash sizes are for the largest memory configuration. Figure 3.2. System Address Space with Core and Code Space Listing silabs.com | Building a more connected world. Rev. 2.20 | 27 EFM32G Data Sheet System Overview Figure 3.3. System Address Space with Peripheral Listing silabs.com | Building a more connected world. Rev. 2.20 | 28 EFM32G Data Sheet Electrical Characteristics 4. Electrical Characteristics 4.1 Test Conditions 4.1.1 Typical Values The typical data are based on TAMB=25°C and VDD=3.0 V, as defined in Table 4.2 General Operating Conditions on page 29, unless otherwise specified. 4.1.2 Minimum and Maximum Values The minimum and maximum values represent the worst conditions of ambient temperature, supply voltage and frequencies, as defined in Table 4.2 General Operating Conditions on page 29, unless otherwise specified. 4.2 Absolute Maximum Ratings The absolute maximum ratings are stress ratings, and functional operation under such conditions are not guaranteed. Stress beyond the limits specified in the following table may affect the device reliability or cause permanent damage to the device. Functional operating conditions are given in Table 4.2 General Operating Conditions on page 29. Table 4.1. Absolute Maximum Ratings Parameter Symbol Storage temperature range TSTG Maximum soldering temperature TS External main supply voltage VDDMAX Voltage on any I/O pin VIOPIN Current per I/O pin (sink) Current per I/O pin (source) Test Condition Min Typ Max Unit -40 — 150 °C — — 260 °C 0 — 3.8 V -0.3 — VDD+0.3 V IIOMAX_SINK — — 100 mA IIOMAX_SOURCE — — -100 mA Latest IPC/JEDEC JSTD-020 Standard 4.3 General Operating Conditions Table 4.2. General Operating Conditions Parameter Symbol Min Typ Max Unit Ambient temperature range TAMB -40 — 85 °C Operating supply voltage VDDOP 1.98 — 3.8 V Internal APB clock frequency fAPB — — 32 MHz Internal AHB clock frequency fAHB — — 32 MHz silabs.com | Building a more connected world. Rev. 2.20 | 29 EFM32G Data Sheet Electrical Characteristics 4.4 Current Consumption Table 4.3. Current Consumption Parameter EM0 current. No prescaling. Running prime number calculation code from Flash. (Production test condition = 14 MHz) Symbol IEM0 EM1 current (Production test IEM1 condition = 14 MHz) EM2 current IEM2 EM3 current IEM3 EM4 current IEM4 silabs.com | Building a more connected world. Test Condition Min Typ Max Unit 32 MHz HFXO, all peripheral clocks disabled, VDD= 3.0 V — 180 — µA/MHz 28 MHz HFRCO, all peripheral clocks disabled, VDD= 3.0 V — 181 206 µA/MHz 21 MHz HFRCO, all peripheral clocks disabled, VDD= 3.0 V — 183 207 µA/MHz 14 MHz HFRCO, all peripheral clocks disabled, VDD= 3.0 V — 185 211 µA/MHz 11 MHz HFRCO, all peripheral clocks disabled, VDD= 3.0 V — 186 215 µA/MHz 6.6 MHz HFRCO, all peripheral clocks disabled, VDD= 3.0 V — 191 218 µA/MHz 1.2 MHz HFRCO, all peripheral clocks disabled, VDD= 3.0 V — 220 — µA/MHz 32 MHz HFXO, all peripheral clocks disabled, VDD= 3.0 V — 45 — µA/MHz 28 MHz HFRCO, all peripheral clocks disabled, VDD= 3.0 V — 47 62 µA/MHz 21 MHz HFRCO, all peripheral clocks disabled, VDD= 3.0 V — 48 64 µA/MHz 14 MHz HFRCO, all peripheral clocks disabled, VDD= 3.0 V — 50 69 µA/MHz 11 MHz HFRCO, all peripheral clocks disabled, VDD= 3.0 V — 51 72 µA/MHz 6.6 MHz HFRCO, all peripheral clocks disabled, VDD= 3.0 V — 56 83 µA/MHz 1.2 MHz HFRCO. all peripheral clocks disabled, VDD= 3.0 V — 103 — µA/MHz EM2 current with RTC prescaled to 1 Hz, 32.768 kHz LFRCO, VDD= 3.0 V, TAMB=25 ºC — 0.9 1.5 μA EM2 current with RTC prescaled to 1 Hz, 32.768 kHz LFRCO, VDD= 3.0 V, TAMB=85 ºC — 3.0 6.0 µA VDD= 3.0 V, TAMB=25 ºC — 0.59 1.0 µA VDD= 3.0 V, TAMB=85 ºC — 2.75 5.8 µA VDD= 3.0 V, TAMB=25 ºC — 0.02 0.045 µA VDD= 3.0 V, TAMB=85 ºC — 0.25 0.7 µA Rev. 2.20 | 30 EFM32G Data Sheet Electrical Characteristics 4.4.1 EM0 Current Consumption 5.3 5.3 85.0°C 65.0°C 5.2 5.2 45.0°C 5.1 5.1 25.0°C Idd [mA] 5.0°C -15.0°C 4.9 4.9 -40.0°C 4.8 4.7 4.6 2.0 5.0 Idd [mA] 5.0 Vdd=2.0V Vdd=2.2V Vdd=2.4V Vdd=2.6V Vdd=2.8V Vdd=3.0V Vdd=3.2V Vdd=3.4V Vdd=3.6V Vdd=3.8V 4.8 4.7 2.2 2.4 2.6 2.8 3.0 Vdd [V] 3.2 3.4 3.6 3.8 4.6 –40 –15 5 25 Temperature [°C] 45 65 85 Figure 4.1. EM0 Current consumption while executing prime number calculation code from flash with HFRCO running at 28 MHz silabs.com | Building a more connected world. Rev. 2.20 | 31 EFM32G Data Sheet Electrical Characteristics 4.0 4.0 85.0°C 65.0°C 3.9 3.9 45.0°C 25.0°C 5.0°C Idd [mA] 3.8 Idd [mA] 3.8 -15.0°C 3.7 Vdd=2.0V Vdd=2.2V Vdd=2.4V Vdd=2.6V Vdd=2.8V Vdd=3.0V Vdd=3.2V Vdd=3.4V Vdd=3.6V Vdd=3.8V 3.7 -40.0°C 3.6 3.5 2.0 3.6 2.2 2.4 2.6 2.8 3.0 Vdd [V] 3.2 3.4 3.6 3.5 –40 3.8 –15 5 25 Temperature [°C] 45 65 85 Figure 4.2. EM0 Current consumption while executing prime number calculation code from flash with HFRCO running at 21 MHz 2.75 2.75 85.0°C 2.70 2.70 65.0°C 2.65 2.65 45.0°C 2.60 2.60 Vdd=2.0V Vdd=2.2V Vdd=2.4V Vdd=2.6V Vdd=2.8V Vdd=3.0V Vdd=3.2V Vdd=3.4V Vdd=3.6V Vdd=3.8V Idd [mA] Idd [mA] 25.0°C 2.55 5.0°C 2.50 -15.0°C 2.50 2.45 -40.0°C 2.45 2.40 2.35 2.0 2.55 2.40 2.2 2.4 2.6 2.8 3.0 Vdd [V] 3.2 3.4 3.6 3.8 2.35 –40 –15 5 25 Temperature [°C] 45 65 85 Figure 4.3. EM0 Current consumption while executing prime number calculation code from flash with HFRCO running at 14 MHz silabs.com | Building a more connected world. Rev. 2.20 | 32 EFM32G Data Sheet Electrical Characteristics 2.20 2.20 85.0°C 2.15 2.15 65.0°C 2.10 2.10 45.0°C 25.0°C 5.0°C 2.05 Idd [mA] Idd [mA] 2.05 Vdd=2.0V Vdd=2.2V Vdd=2.4V Vdd=2.6V Vdd=2.8V Vdd=3.0V Vdd=3.2V Vdd=3.4V Vdd=3.6V Vdd=3.8V 2.00 2.00 -15.0°C 1.95 1.95 -40.0°C 1.90 1.85 2.0 1.90 2.2 2.4 2.6 2.8 3.0 Vdd [V] 3.2 3.4 3.6 1.85 –40 3.8 –15 5 25 Temperature [°C] 45 65 85 Figure 4.4. EM0 Current consumption while executing prime number calculation code from flash with HFRCO running at 11 MHz 1.45 1.45 85.0°C 1.40 1.40 65.0°C 45.0°C 1.35 1.35 Vdd=2.0V Vdd=2.2V Vdd=2.4V Vdd=2.6V Vdd=2.8V Vdd=3.0V Vdd=3.2V Vdd=3.4V Vdd=3.6V Vdd=3.8V 5.0°C -15.0°C 1.30 Idd [mA] Idd [mA] 25.0°C 1.30 -40.0°C 1.25 1.20 2.0 1.25 2.2 2.4 2.6 2.8 3.0 Vdd [V] 3.2 3.4 3.6 3.8 1.20 –40 –15 5 25 Temperature [°C] 45 65 85 Figure 4.5. EM0 Current consumption while executing prime number calculation code from flash with HFRCO running at 7 MHz silabs.com | Building a more connected world. Rev. 2.20 | 33 EFM32G Data Sheet Electrical Characteristics 4.4.2 EM1 Current Consumption 1.40 1.40 85.0°C 65.0°C 1.35 1.35 Vdd=2.0V Vdd=2.4V Vdd=2.8V Vdd=3.0V Vdd=3.4V Vdd=3.8V 45.0°C 25.0°C 1.30 1.30 -15.0°C Idd [mA] Idd [mA] 5.0°C -40.0°C 1.25 1.25 1.20 1.15 2.0 1.20 2.2 2.4 2.6 2.8 3.0 Vdd [V] 3.2 3.4 3.6 1.15 –40 3.8 –15 5 25 Temperature [°C] 45 65 85 Figure 4.6. EM1 Current consumption with all peripheral clocks disabled and HFRCO running at 28 MHz 1.08 1.08 85.0°C 1.06 1.04 65.0°C 1.04 1.02 45.0°C 1.02 25.0°C 1.00 5.0°C Idd [mA] Idd [mA] 1.06 1.00 0.98 -15.0°C 0.98 0.96 -40.0°C 0.96 0.94 0.92 2.0 Vdd=2.0V Vdd=2.4V Vdd=2.8V Vdd=3.0V Vdd=3.4V Vdd=3.8V 0.94 2.2 2.4 2.6 2.8 3.0 Vdd [V] 3.2 3.4 3.6 3.8 0.92 –40 –15 5 25 Temperature [°C] 45 65 85 Figure 4.7. EM1 Current consumption with all peripheral clocks disabled and HFRCO running at 21 MHz silabs.com | Building a more connected world. Rev. 2.20 | 34 EFM32G Data Sheet Electrical Characteristics 0.76 0.76 85.0°C 0.74 0.74 65.0°C 0.72 Vdd=2.0V Vdd=2.4V Vdd=2.8V Vdd=3.0V Vdd=3.4V Vdd=3.8V 0.72 25.0°C 0.70 5.0°C Idd [mA] Idd [mA] 45.0°C 0.70 -15.0°C 0.68 0.68 -40.0°C 0.66 0.64 2.0 0.66 2.2 2.4 2.6 2.8 3.0 Vdd [V] 3.2 3.4 3.6 0.64 –40 3.8 –15 5 25 Temperature [°C] 45 65 85 Figure 4.8. EM1 Current consumption with all peripheral clocks disabled and HFRCO running at 14 MHz 0.62 0.60 65.0°C 0.60 0.58 45.0°C 0.58 25.0°C 5.0°C 0.56 -15.0°C Vdd=2.0V Vdd=2.4V Vdd=2.8V Vdd=3.0V Vdd=3.4V Vdd=3.8V Idd [mA] 85.0°C Idd [mA] 0.62 0.56 -40.0°C 0.54 0.52 2.0 0.54 2.2 2.4 2.6 2.8 3.0 Vdd [V] 3.2 3.4 3.6 3.8 0.52 –40 –15 5 25 Temperature [°C] 45 65 85 Figure 4.9. EM1 Current consumption with all peripheral clocks disabled and HFRCO running at 11 MHz silabs.com | Building a more connected world. Rev. 2.20 | 35 EFM32G Data Sheet Electrical Characteristics 0.44 0.44 85.0°C 0.43 0.43 65.0°C 0.42 Vdd=2.0V Vdd=2.4V Vdd=2.8V Vdd=3.0V Vdd=3.4V Vdd=3.8V 0.42 0.41 0.41 25.0°C 0.40 5.0°C -15.0°C 0.39 Idd [mA] Idd [mA] 45.0°C 0.40 0.39 -40.0°C 0.38 0.38 0.37 0.37 0.36 2.0 2.2 2.4 2.6 2.8 3.0 Vdd [V] 3.2 3.4 3.6 3.8 0.36 –40 –15 5 25 Temperature [°C] 45 65 85 Figure 4.10. EM1 Current consumption with all peripheral clocks disabled and HFRCO running at 7 MHz silabs.com | Building a more connected world. Rev. 2.20 | 36 EFM32G Data Sheet Electrical Characteristics 4.4.3 EM2 Current Consumption 3.5 3.5 -40.0°C -15.0°C 5.0°C 25.0°C 45.0°C 65.0°C 85.0°C 3.0 3.0 2.5 Idd [uA] Idd [uA] 2.5 2.0 2.0 1.5 1.5 1.0 1.0 0.5 1.8 Vdd=1.8V Vdd=2.2V Vdd=2.6V Vdd=3.0V Vdd=3.4V Vdd=3.8V 2.0 2.2 2.4 2.6 2.8 Vdd [V] 3.0 3.2 3.4 3.6 3.8 0.5 –40 –15 5 25 Temperature [°C] 45 65 85 Figure 4.11. EM2 Current Consumption, RTC prescaled to 1 kHz, 32.768 kHz LFRCO silabs.com | Building a more connected world. Rev. 2.20 | 37 EFM32G Data Sheet Electrical Characteristics 4.4.4 EM3 Current Consumption 3.0 3.0 -40.0°C -15.0°C 5.0°C 25.0°C 45.0°C 65.0°C 85.0°C 2.5 2.5 2.0 Idd [uA] Idd [uA] 2.0 1.5 1.5 1.0 1.0 0.5 0.5 0.0 1.8 Vdd=1.8V Vdd=2.2V Vdd=2.6V Vdd=3.0V Vdd=3.4V Vdd=3.8V 2.0 2.2 2.4 2.6 2.8 Vdd [V] 3.0 3.2 3.4 3.6 3.8 0.0 –40 –15 5 25 Temperature [°C] 45 65 85 Figure 4.12. EM3 Current Consumption silabs.com | Building a more connected world. Rev. 2.20 | 38 EFM32G Data Sheet Electrical Characteristics 4.4.5 EM4 Current Consumption 0.45 0.40 0.35 0.30 0.30 0.25 0.25 0.20 0.20 0.15 0.15 0.10 0.10 0.05 0.05 0.00 1.8 2.0 2.2 Vdd=1.8V Vdd=2.2V Vdd=2.6V Vdd=3.0V Vdd=3.4V Vdd=3.8V 0.40 Idd [uA] Idd [uA] 0.35 0.45 -40.0°C -15.0°C 5.0°C 25.0°C 45.0°C 65.0°C 85.0°C 2.4 2.6 2.8 Vdd [V] 3.0 3.2 3.4 3.6 3.8 0.00 –40 –15 5 25 Temperature [°C] 45 65 85 Figure 4.13. EM4 Current Consumption 4.5 Transition between Energy Modes The transition times are measured from the trigger to the first clock edge in the CPU. Table 4.4. Energy Modes Transitions Parameter Symbol Min Typ Max Unit Transition time from EM1 to EM0 tEM10 — 0 — HFCORECLK cycles Transition time from EM2 to EM0 tEM20 — 2 — µs Transition time from EM3 to EM0 tEM30 — 2 — µs Transition time from EM4 to EM0 tEM40 — 163 — µs silabs.com | Building a more connected world. Rev. 2.20 | 39 EFM32G Data Sheet Electrical Characteristics 4.6 Power Management The EFM32G requires the AVDD_x, VDD_DREG and IOVDD_x pins to be connected together (with optional filter) at the PCB level. For practical schematic recommendations, please see the application note, "AN0002 EFM32 Hardware Design Considerations". Table 4.5. Power Management Parameter Symbol Test Condition Min Typ Max Unit BOD threshold on falling external supply voltage VBODextthr- EM0 1.74 — 1.96 V EM1 1.74 — 1.96 V EM2 1.74 — 1.96 V EM0 — 1.85 — V — — 1.98 V — 163 — µs BOD threshold on rising external supply voltage VBODextthr+ Power-on Reset (POR) threshold on rising external supply voltage VPORthr+ Delay from reset is released until program execution starts tRESETdly negative pulse length to ensure complete reset of device tRESET 50 — — ns Voltage regulator decoupling capacitor. CDECOUPLE X5R capacitor recommended. Apply between DECOUPLE pin and GROUND — 1 — µF silabs.com | Building a more connected world. Applies to Power-on Reset, Brown-out Reset and pin reset. Rev. 2.20 | 40 EFM32G Data Sheet Electrical Characteristics 4.7 Flash Table 4.6. Flash Parameter Symbol Flash erase cycles before failure ECFLASH Test Condition Min Typ Max Unit 20000 — — cycles — — 21 cycles TAMB