EFM32LG842F128G-E-QFP64R

EFM32 Leopard Gecko Family EFM32LG Data Sheet The EFM32 Leopard Gecko MCUs are the world’s most energyfriendly microcontrollers. The EFM32LG offers unmatched performance and ultra-low power consumption in both active and sleep modes. EFM32LG devices consume as little as 0.65 μA in Stop mode and 211 μA/MHz in Run mode. It also features autonomous peripherals, high overall chip and analog integration, and the performance of the industry standard 32-bit ARM CortexM3 processor, making it perfect for battery-powered systems and systems with high-performance, low-energy requirements. ARM Cortex M3 processor Clock Management Memory Protection Unit Flash Program Memory Debug w/ ETM RAM Memory DMA Controller • Ultra-low power operation • 0.65 μA current in Stop (EM3), with brown-out detection and RAM retention • 63 μA/MHz in EM1 • 211 μA/MHz in Run mode (EM0) • Hardware cryptography (AES) • Alarm and security systems • Industrial and home automation Core / Memory TM • ARM Cortex-M3 at 48 MHz • Fast wake-up time of 2 µs EFM32LG applications include the following: • Energy, gas, water and smart metering • Health and fitness applications • Smart accessories KEY FEATURES • Up to 256 kB of flash and 32 kB of RAM Energy Management High Frequency Crystal Oscillator High Frequency RC Oscillator Voltage Regulator Voltage Comparator Auxiliary High Freq. RC Osc. Low Freq. RC Oscillator Brown-out Detector Power-on Reset Low Frequency Crystal Oscillator Ultra Low Freq. RC Oscillator Back-up Power Domain Security Hardware AES 32-bit bus Peripheral Reflex System Serial Interfaces USART Low Energy UARTTM UART I2C USB I/O Ports External Bus Interface Timers and Triggers TFT Driver External Interrupts General Purpose I/O Pin Reset Pin Wakeup Timer/Counter LESENSE Low Energy Timer Real Time Counter Pulse Counter Watchdog Timer Analog Interfaces ADC LCD Controller DAC Operational Amplifier Analog Comparator Back-up RTC Lowest power mode with peripheral operational: EM0 - Active silabs.com | Building a more connected world. EM1 - Sleep EM2 – Deep Sleep EM3 - Stop Copyright © 2022 by Silicon Laboratories EM4 - Shutoff Rev. 2.40 EFM32LG Data Sheet Feature List 1. Feature List • ARM Cortex-M3 CPU platform • High Performance 32-bit processor @ up to 48 MHz • Memory Protection Unit • Wake-up Interrupt Controller • SysTick System Timer • Flexible Energy Management System • 20 nA @ 3 V Shutoff Mode • 0.4 µA @ 3 V Shutoff Mode with RTC • 0.65 µA @ 3 V Stop Mode, including Power-on Reset, Brown-out Detector, RAM and CPU retention • 0.95 µA @ 3 V Deep Sleep Mode, including RTC with 32.768 kHz oscillator, Power-on Reset, Brown-out Detector, RAM and CPU retention • 63 µA/MHz @ 3 V Sleep Mode • 211 µA/MHz @ 3 V Run Mode, with code executed from flash • 256/128/64 kB flash • 32 kB RAM • Up to 93 General Purpose I/O pins • Configurable push-pull, open-drain, pull-up/down, input filter, drive strength • Configurable peripheral I/O locations • 16 asynchronous external interrupts • Output state retention and wake-up from Shutoff Mode • 12 Channel DMA Controller • 12 Channel Peripheral Reflex System (PRS) for autonomous inter-peripheral signaling • Hardware AES with 128/256-bit keys in 54/75 cycles • Timers/Counters • 4× 16-bit Timer/Counter • 4×3 Compare/Capture/PWM channels • Dead-Time Insertion on TIMER0 • 16-bit Low Energy Timer • 1× 24-bit Real-Time Counter and 1× 32-bit Real-Time Counter • 3× 16/8-bit Pulse Counter • Watchdog Timer with dedicated RC oscillator @ 50 nA • Integrated LCD Controller for up to 8×36 segments • Voltage boost, adjustable contrast, and autonomous animation • Backup Power Domain • RTC and retention registers in a separate power domain, available in all energy modes • Operation from backup battery when main power drains out • External Bus Interface for up to 4x256 MB of external memory mapped space • TFT Controller with Direct Drive • Communication interfaces • Up to 3× Universal Synchronous/Asynchronous Receiver/Transmitter • UART/SPI/SmartCard (ISO 7816)/IrDA/I2S • 2× Universal Asynchronous Receiver/Transmitter • 2× Low Energy UART • Autonomous operation with DMA in Deep Sleep Mode • 2× I2C Interface with SMBus support • Address recognition in Stop Mode • Universal Serial Bus (USB) with Host & OTG support • Fully USB 2.0 compliant • On-chip PHY and embedded 5 to 3.3 V regulator silabs.com | Building a more connected world. Rev. 2.40 | 2 EFM32LG Data Sheet Feature List • Ultra-low power precision analog peripherals • 12-bit 1 Msamples/s Analog to Digital Converter • 8 single-ended channels/4 differential channels • On-chip temperature sensor • 12-bit 500 ksamples/s Digital to Analog Converter • 2 single-ended channels/1 differential channel • Up to 2× Analog Comparator • Capacitive sensing with up to 16 inputs • 3× Operational Amplifier • 6.1 MHz GBW, Rail-to-rail, Programmable Gain • Supply Voltage Comparator • Low Energy Sensor Interface (LESENSE) • Autonomous sensor monitoring in Deep Sleep Mode • Wide range of sensors supported, including LC sensors and capacitive buttons • Ultra efficient Power-on Reset and Brown-Out Detector • Debug Interface • 2-pin Serial Wire Debug interface • 1-pin Serial Wire Viewer • Embedded Trace Module v3.5 (ETM) • Pre-programmed USB/UART Bootloader • Temperature range -40 to 85 ºC • Single power supply 1.98 to 3.8 V • Packages: • BGA112 • BGA120 • CSP81 • LQFP100 • TQFP64 • QFN64 • Full wafer silabs.com | Building a more connected world. Rev. 2.40 | 3 EFM32LG Data Sheet Ordering Information 2. Ordering Information The following table shows the available EFM32LG devices. Table 2.1. Ordering Information Flash (kB) RAM (kB) Max Speed (MHz) Supply Voltage (V) Temperature (ºC) Package EFM32LG230F64G-F-QFN64 64 32 48 1.98 - 3.8 -40 - 85 QFN64 EFM32LG230F128G-F-QFN64 128 32 48 1.98 - 3.8 -40 - 85 QFN64 EFM32LG230F256G-F-QFN64 256 32 48 1.98 - 3.8 -40 - 85 QFN64 EFM32LG232F64G-F-QFP64 64 32 48 1.98 - 3.8 -40 - 85 TQFP64 EFM32LG232F128G-F-QFP64 128 32 48 1.98 - 3.8 -40 - 85 TQFP64 EFM32LG232F256G-F-QFP64 256 32 48 1.98 - 3.8 -40 - 85 TQFP64 EFM32LG280F64G-F-QFP1001 64 32 48 1.98 - 3.8 -40 - 85 LQFP100 EFM32LG280F128G-F-QFP100 128 32 48 1.98 - 3.8 -40 - 85 LQFP100 EFM32LG280F256G-F-QFP100 256 32 48 1.98 - 3.8 -40 - 85 LQFP100 EFM32LG290F64G-F-BGA1121 64 32 48 1.98 - 3.8 -40 - 85 BGA112 EFM32LG290F128G-F-BGA1121 128 32 48 1.98 - 3.8 -40 - 85 BGA112 EFM32LG290F256G-F-BGA112 256 32 48 1.98 - 3.8 -40 - 85 BGA112 EFM32LG295F64G-F-BGA1201 64 32 48 1.98 - 3.8 -40 - 85 BGA120 EFM32LG295F128G-F-BGA1201 128 32 48 1.98 - 3.8 -40 - 85 BGA120 EFM32LG295F256G-F-BGA120 256 32 48 1.98 - 3.8 -40 - 85 BGA120 EFM32LG330F64G-F-QFN641 64 32 48 1.98 - 3.8 -40 - 85 QFN64 EFM32LG330F128G-F-QFN64 128 32 48 1.98 - 3.8 -40 - 85 QFN64 EFM32LG330F256G-F-QFN64 256 32 48 1.98 - 3.8 -40 - 85 QFN64 EFM32LG332F64G-F-QFP641 64 32 48 1.98 - 3.8 -40 - 85 TQFP64 EFM32LG332F128G-F-QFP64 128 32 48 1.98 - 3.8 -40 - 85 TQFP64 EFM32LG332F256G-F-QFP64 256 32 48 1.98 - 3.8 -40 - 85 TQFP64 EFM32LG360F64G-F-CSP811 64 32 48 1.98 - 3.8 -40 - 85 CSP81 EFM32LG360F128G-F-CSP811 128 32 48 1.98 - 3.8 -40 - 85 CSP81 EFM32LG360F256G-F-CSP81 256 32 48 1.98 - 3.8 -40 - 85 CSP81 EFM32LG380F64G-F-QFP1001 64 32 48 1.98 - 3.8 -40 - 85 LQFP100 EFM32LG380F128G-F-QFP1001 128 32 48 1.98 - 3.8 -40 - 85 LQFP100 EFM32LG380F256G-F-QFP100 256 32 48 1.98 - 3.8 -40 - 85 LQFP100 EFM32LG390F64G-F-BGA1121 64 32 48 1.98 - 3.8 -40 - 85 BGA112 EFM32LG390F128G-F-BGA1121 128 32 48 1.98 - 3.8 -40 - 85 BGA112 EFM32LG390F256G-F-BGA112 256 32 48 1.98 - 3.8 -40 - 85 BGA112 EFM32LG395F64G-F-BGA1201 64 32 48 1.98 - 3.8 -40 - 85 BGA120 Ordering Code silabs.com | Building a more connected world. Rev. 2.40 | 4 EFM32LG Data Sheet Ordering Information Flash (kB) RAM (kB) Max Speed (MHz) Supply Voltage (V) Temperature (ºC) Package EFM32LG395F128G-F-BGA1201 128 32 48 1.98 - 3.8 -40 - 85 BGA120 EFM32LG395F256G-F-BGA120 256 32 48 1.98 - 3.8 -40 - 85 BGA120 EFM32LG840F64G-F-QFN64 64 32 48 1.98 - 3.8 -40 - 85 QFN64 EFM32LG840F128G-F-QFN64 128 32 48 1.98 - 3.8 -40 - 85 QFN64 EFM32LG840F256G-F-QFN64 256 32 48 1.98 - 3.8 -40 - 85 QFN64 EFM32LG842F64G-F-QFP641 64 32 48 1.98 - 3.8 -40 - 85 TQFP64 EFM32LG842F128G-F-QFP64 128 32 48 1.98 - 3.8 -40 - 85 TQFP64 EFM32LG842F256G-F-QFP64 256 32 48 1.98 - 3.8 -40 - 85 TQFP64 EFM32LG880F64G-F-QFP100 64 32 48 1.98 - 3.8 -40 - 85 LQFP100 EFM32LG880F128G-F-QFP100 128 32 48 1.98 - 3.8 -40 - 85 LQFP100 EFM32LG880F256G-F-QFP100 256 32 48 1.98 - 3.8 -40 - 85 LQFP100 EFM32LG890F64G-F-BGA1121 64 32 48 1.98 - 3.8 -40 - 85 BGA112 EFM32LG890F128G-F-BGA1121 128 32 48 1.98 - 3.8 -40 - 85 BGA112 EFM32LG890F256G-F-BGA112 256 32 48 1.98 - 3.8 -40 - 85 BGA112 EFM32LG895F64G-F-BGA1201 64 32 48 1.98 - 3.8 -40 - 85 BGA120 EFM32LG895F128G-F-BGA1201 128 32 48 1.98 - 3.8 -40 - 85 BGA120 EFM32LG895F256G-F-BGA120 256 32 48 1.98 - 3.8 -40 - 85 BGA120 EFM32LG900F256G-F-D1I 1 256 32 48 1.98 - 3.8 -40 - 85 Wafer EFM32LG940F64G-F-QFN641 64 32 48 1.98 - 3.8 -40 - 85 QFN64 EFM32LG940F128G-F-QFN64 128 32 48 1.98 - 3.8 -40 - 85 QFN64 EFM32LG940F256G-F-QFN64 256 32 48 1.98 - 3.8 -40 - 85 QFN64 EFM32LG942F64G-F-QFP641 64 32 48 1.98 - 3.8 -40 - 85 TQFP64 EFM32LG942F128G-F-QFP64 128 32 48 1.98 - 3.8 -40 - 85 TQFP64 EFM32LG942F256G-F-QFP64 256 32 48 1.98 - 3.8 -40 - 85 TQFP64 EFM32LG980F64G-F-QFP1001 64 32 48 1.98 - 3.8 -40 - 85 LQFP100 EFM32LG980F128G-F-QFP1001 128 32 48 1.98 - 3.8 -40 - 85 LQFP100 EFM32LG980F256G-F-QFP100 256 32 48 1.98 - 3.8 -40 - 85 LQFP100 EFM32LG990F64G-F-BGA1121 64 32 48 1.98 - 3.8 -40 - 85 BGA112 EFM32LG990F128G-F-BGA1121 128 32 48 1.98 - 3.8 -40 - 85 BGA112 EFM32LG990F256G-F-BGA112 256 32 48 1.98 - 3.8 -40 - 85 BGA112 EFM32LG995F64G-F-BGA1201 64 32 48 1.98 - 3.8 -40 - 85 BGA120 EFM32LG995F128G-F-BGA1201 128 32 48 1.98 - 3.8 -40 - 85 BGA120 EFM32LG995F256G-F-BGA120 256 32 48 1.98 - 3.8 -40 - 85 BGA120 Ordering Code Note: 1. Not recommended for new designs. silabs.com | Building a more connected world. Rev. 2.40 | 5 EFM32LG Data Sheet Ordering Information EFM32 LG 995 F 256 G – F – BGA 120 R Tape and Reel (Optional) Pin Count Package Revision Temperature Grade – G (-40 to +85 °C) Memory Size in kB Memory Type (Flash) Feature Set Code Leopard Gecko Energy Friendly Microcontroller 32-bit Figure 2.1. Ordering Code Decoder Adding the suffix 'R' to the part number (e.g. EFM32LGF256G-F-BGA120R) denotes tape and reel. Visit www.silabs.com for information on global distributors and representatives. silabs.com | Building a more connected world. Rev. 2.40 | 6 Table of Contents 1. Feature List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 2. Ordering Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 3. System Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 3.1 System Introduction . . . . . . . . . . . . . . . . . . . 3.1.1 ARM Cortex-M3 Core . . . . . . . . . . . . . . . . . 3.1.2 Debug Interface (DBG) . . . . . . . . . . . . . . . . . 3.1.3 Memory System Controller (MSC) . . . . . . . . . . . . . 3.1.4 Direct Memory Access Controller (DMA) . . . . . . . . . . . 3.1.5 Reset Management Unit (RMU) . . . . . . . . . . . . . . 3.1.6 Energy Management Unit (EMU) . . . . . . . . . . . . . 3.1.7 Clock Management Unit (CMU) . . . . . . . . . . . . . . 3.1.8 Watchdog (WDOG) . . . . . . . . . . . . . . . . . . 3.1.9 Peripheral Reflex System (PRS) . . . . . . . . . . . . . 3.1.10 External Bus Interface (EBI) . . . . . . . . . . . . . . 3.1.11 TFT Direct Drive . . . . . . . . . . . . . . . . . . 3.1.12 Universal Serial Bus Controller (USB) . . . . . . . . . . . 3.1.13 Inter-Integrated Circuit Interface (I2C) . . . . . . . . . . . 3.1.14 Universal Synchronous/Asynchronous Receiver/Transmitter (USART) 3.1.15 Pre-Programmed USB/UART Bootloader . . . . . . . . . . 3.1.16 Universal Asynchronous Receiver/Transmitter (UART) . . . . . 3.1.17 Low Energy Universal Asynchronous Receiver/Transmitter (LEUART) 3.1.18 Timer/Counter (TIMER) . . . . . . . . . . . . . . . . 3.1.19 Real Time Counter (RTC) . . . . . . . . . . . . . . . 3.1.20 Backup Real Time Counter (BURTC) . . . . . . . . . . . 3.1.21 Low Energy Timer (LETIMER) . . . . . . . . . . . . . . 3.1.22 Pulse Counter (PCNT) . . . . . . . . . . . . . . . . 3.1.23 Analog Comparator (ACMP) . . . . . . . . . . . . . . 3.1.24 Voltage Comparator (VCMP) . . . . . . . . . . . . . . 3.1.25 Analog to Digital Converter (ADC) . . . . . . . . . . . . 3.1.26 Digital to Analog Converter (DAC) . . . . . . . . . . . . 3.1.27 Operational Amplifier (OPAMP) . . . . . . . . . . . . . 3.1.28 Low Energy Sensor Interface (LESENSE) . . . . . . . . . . 3.1.29 Backup Power Domain . . . . . . . . . . . . . . . . 3.1.30 Advanced Encryption Standard Accelerator (AES) . . . . . . . 3.1.31 General Purpose Input/Output (GPIO) . . . . . . . . . . . 3.1.32 Liquid Crystal Display Driver (LCD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13 .13 .13 .13 .13 .13 .14 .14 .14 .14 .14 .14 .14 .14 .14 .15 .15 .15 .15 .15 .15 .15 .15 .15 .15 .16 .16 .16 .16 .16 .16 .16 .16 3.2 Configuration Summary 3.2.1 EFM32LG230 . . 3.2.2 EFM32LG232 . . 3.2.3 EFM32LG280 . . 3.2.4 EFM32LG290 . . 3.2.5 EFM32LG295 . . 3.2.6 EFM32LG330 . . 3.2.7 EFM32LG332 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 .17 .19 .21 .23 .25 .27 .29 . . . . . . . . silabs.com | Building a more connected world. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Rev. 2.40 | 7 3.2.8 EFM32LG360 . 3.2.9 EFM32LG380 . 3.2.10 EFM32LG390 3.2.11 EFM32LG395 3.2.12 EFM32LG840 3.2.13 EFM32LG842 3.2.14 EFM32LG880 3.2.15 EFM32LG890 3.2.16 EFM32LG895 3.2.17 EFM32LG900 3.2.18 EFM32LG940 3.2.19 EFM32LG942 3.2.20 EFM32LG980 3.2.21 EFM32LG990 3.2.22 EFM32LG995 3.3 Memory Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31 .33 .35 .37 .39 .41 .43 .45 .47 .49 .51 .53 .55 .57 .59 . . . . . . . . . . . . . . . . . . . . . . . . . . . .61 4. Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . 63 4.1 Test Conditions . . . . . . . . 4.1.1 Typical Values . . . . . . 4.1.2 Minimum and Maximum Values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63 .63 .63 4.2 Absolute Maximum Ratings. . . . . . . . . . . . . . . . . . . . . . . . . .63 4.3 General Operating Conditions . . . . . . . . . . . . . . . . . . . . . . . . .63 4.4 Backup Supply Domain . . . . . . . . . . . . . . . . . . . . . . . . . .64 4.5 Current Consumption . . . . 4.5.1 EM1 Current Consumption 4.5.2 EM2 Current Consumption 4.5.3 EM3 Current Consumption 4.5.4 EM4 Current Consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65 .67 .70 .71 .71 4.6 Transition between Energy Modes . . . . . . . . . . . . . . . . . . . . . . .72 4.7 Power Management . . . . . . . . . . . . . . . . . . . . . . . . . . . .72 4.8 Flash . . . . . . . . . . . . . . . . . . . . . . . . . . . .73 4.9 General Purpose Input Output . . . . . . . . . . . . . . . . . . . . . . . . .74 4.10 Oscillators . . 4.10.1 LFXO . . 4.10.2 HFXO . . 4.10.3 LFRCO . 4.10.4 HFRCO . 4.10.5 AUXHFRCO 4.10.6 ULFRCO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .82 .82 .83 .84 .85 .90 .90 4.11 Analog Digital Converter (ADC) . 4.11.1 Typical Performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91 .97 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.12 Digital Analog Converter (DAC) . . . . . . . . . . . . . . . . . . . . . . . 102 4.13 Operational Amplifier (OPAMP) . . . . . . . . . . . . . . . . . . . . . . . 104 silabs.com | Building a more connected world. Rev. 2.40 | 8 4.14 Analog Comparator (ACMP) . . 4.15 Voltage Comparator (VCMP) . 4.16 EBI 4.17 LCD 4.18 I2C . . . . . . . . 4.19 USART SPI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111 . 119 . . . . 1 . 20 . 125 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1. 26 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128 . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.20 Digital Peripherals .130 5. Pin Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131 5.1 EFM32LG230 (QFN64) . . . . . . . . . . . . . . . . . . . . . . . . . . 131 5.1.1 Pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . 31 5.1.2 Alternate Functionality Pinout . . . . . . . . . . . . . . . . . . . . . 135 . 5.1.3 GPIO Pinout Overview . . . . . . . . . . . . . . . . . . . . . . . . . 140 5.1.4 Opamp Pinout Overview . . . . . . . . . . . . . . . . . . . . . . . .140 5.2 EFM32LG232 (TQFP64) . . . . . . . . . . . . . . . . . . . . . . . . 141 . 5.2.1 Pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . 41 5.2.2 Alternate Functionality Pinout . . . . . . . . . . . . . . . . . . . . . 145 . 5.2.3 GPIO Pinout Overview . . . . . . . . . . . . . . . . . . . . . . . . . 149 5.2.4 Opamp Pinout Overview . . . . . . . . . . . . . . . . . . . . . . . .150 5.3 EFM32LG280 (LQFP100) . . . . . . . . . . . . . . . . . . . . . . . . .151 5.3.1 Pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . 51 5.3.2 Alternate Functionality Pinout . . . . . . . . . . . . . . . . . . . . . 157 . 5.3.3 GPIO Pinout Overview . . . . . . . . . . . . . . . . . . . . . . . . . 164 5.3.4 Opamp Pinout Overview . . . . . . . . . . . . . . . . . . . . . . . .164 5.4 EFM32LG290 (BGA112) . . . . . . . . . . . . . . . . . . . . . . . . 165 . 5.4.1 Pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . 65 5.4.2 Alternate Functionality Pinout . . . . . . . . . . . . . . . . . . . . . 171 . 5.4.3 GPIO Pinout Overview . . . . . . . . . . . . . . . . . . . . . . . . . 178 5.4.4 Opamp Pinout Overview . . . . . . . . . . . . . . . . . . . . . . . .178 5.5 EFM32LG295 (BGA120) . . . . . . . . . . . . . . . . . . . . . . . . 179 . 5.5.1 Pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . 79 5.5.2 Alternate Functionality Pinout . . . . . . . . . . . . . . . . . . . . . 185 . 5.5.3 GPIO Pinout Overview . . . . . . . . . . . . . . . . . . . . . . . . . 192 5.5.4 Opamp Pinout Overview . . . . . . . . . . . . . . . . . . . . . . . .192 5.6 EFM32LG330 (QFN64) . . . . . . . . . . . . . . . . . . . . . . . . . . 193 5.6.1 Pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . 93 5.6.2 Alternate Functionality Pinout . . . . . . . . . . . . . . . . . . . . . 197 . 5.6.3 GPIO Pinout Overview . . . . . . . . . . . . . . . . . . . . . . . . . 202 5.6.4 Opamp Pinout Overview . . . . . . . . . . . . . . . . . . . . . . . .202 5.7 EFM32LG332 (TQFP64) . . . . . . . . . . . . . . . . . . . . . . . . 203 . 5.7.1 Pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 . 03 5.7.2 Alternate Functionality Pinout . . . . . . . . . . . . . . . . . . . . . 207 . 5.7.3 GPIO Pinout Overview . . . . . . . . . . . . . . . . . . . . . . . . . 211 5.7.4 Opamp Pinout Overview . . . . . . . . . . . . . . . . . . . . . . . .212 5.8 EFM32LG360 (CSP81) . silabs.com | Building a more connected world. . . . . . . . . . . . . . . . . . . . . . . . . . 213 Rev. 2.40 | 9 5.8.1 5.8.2 5.8.3 5.8.4 Pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 . 13 Alternate Functionality Pinout . . . . . . . . . . . . . . . . . . . . . 218 . GPIO Pinout Overview . . . . . . . . . . . . . . . . . . . . . . . . . 223 Opamp Pinout Overview . . . . . . . . . . . . . . . . . . . . . . . .223 5.9 EFM32LG380 (LQFP100) . . . . . . . . . . . . . . . . . . . . . . . . .224 5.9.1 Pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 . 24 5.9.2 Alternate Functionality Pinout . . . . . . . . . . . . . . . . . . . . . 229 . 5.9.3 GPIO Pinout Overview . . . . . . . . . . . . . . . . . . . . . . . . . 236 5.9.4 Opamp Pinout Overview . . . . . . . . . . . . . . . . . . . . . . . .236 5.10 EFM32LG390 (BGA112) . . . . . . . . . . . . . . . . . . . . . . . . .237 5.10.1 Pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 237 5.10.2 Alternate Functionality Pinout . . . . . . . . . . . . . . . . . . . . . .243 5.10.3 GPIO Pinout Overview . . . . . . . . . . . . . . . . . . . . . . . 2 . 50 5.10.4 Opamp Pinout Overview . . . . . . . . . . . . . . . . . . . . . . . . 250 5.11 EFM32LG395 (BGA120) . . . . . . . . . . . . . . . . . . . . . . . . .251 5.11.1 Pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 251 5.11.2 Alternate Functionality Pinout . . . . . . . . . . . . . . . . . . . . . .257 5.11.3 GPIO Pinout Overview . . . . . . . . . . . . . . . . . . . . . . . 2 . 64 5.11.4 Opamp Pinout Overview . . . . . . . . . . . . . . . . . . . . . . . . 265 5.12 EFM32LG840 (QFN64) . . . . . . . . . . . . . . . . . . . . . . . . 266 . 5.12.1 Pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 266 5.12.2 Alternate Functionality Pinout . . . . . . . . . . . . . . . . . . . . . .270 5.12.3 GPIO Pinout Overview . . . . . . . . . . . . . . . . . . . . . . . 2 . 76 5.12.4 Opamp Pinout Overview . . . . . . . . . . . . . . . . . . . . . . . . 276 5.13 EFM32LG842 (TQFP64) . . . . . . . . . . . . . . . . . . . . . . . . .277 5.13.1 Pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 277 5.13.2 Alternate Functionality Pinout . . . . . . . . . . . . . . . . . . . . . .281 5.13.3 GPIO Pinout Overview . . . . . . . . . . . . . . . . . . . . . . . 2 . 87 5.13.4 Opamp Pinout Overview . . . . . . . . . . . . . . . . . . . . . . . . 287 5.14 EFM32LG880 (LQFP100) . . . . . . . . . . . . . . . . . . . . . . . . . 288 5.14.1 Pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 288 5.14.2 Alternate Functionality Pinout . . . . . . . . . . . . . . . . . . . . . .294 5.14.3 GPIO Pinout Overview . . . . . . . . . . . . . . . . . . . . . . . 3 . 03 5.14.4 Opamp Pinout Overview . . . . . . . . . . . . . . . . . . . . . . . . 304 5.15 EFM32LG890 (BGA112) . . . . . . . . . . . . . . . . . . . . . . . . .305 5.15.1 Pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 305 5.15.2 Alternate Functionality Pinout . . . . . . . . . . . . . . . . . . . . . .311 5.15.3 GPIO Pinout Overview . . . . . . . . . . . . . . . . . . . . . . . 3 . 20 5.15.4 Opamp Pinout Overview . . . . . . . . . . . . . . . . . . . . . . . . 321 5.16 EFM32LG895 (BGA120) . . . . . . . . . . . . . . . . . . . . . . . . .322 5.16.1 Pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 322 5.16.2 Alternate Functionality Pinout . . . . . . . . . . . . . . . . . . . . . .328 5.16.3 GPIO Pinout Overview . . . . . . . . . . . . . . . . . . . . . . . 3 . 37 5.16.4 Opamp Pinout Overview . . . . . . . . . . . . . . . . . . . . . . . . 337 5.17 EFM32LG900 (Wafer) . . . . . . . . . . . . . . . . . . . . . . . . . . 338 5.17.1 Padout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 338 silabs.com | Building a more connected world. Rev. 2.40 | 10 5.17.2 Alternate Functionality Padout . . . . . . . . . . . . . . . . . . . . . . 344 5.17.3 GPIO Pinout Overview . . . . . . . . . . . . . . . . . . . . . . . 3 . 53 5.17.4 Opamp Pinout Overview . . . . . . . . . . . . . . . . . . . . . . . . 354 5.18 EFM32LG940 (QFN64) . . . . . . . . . . . . . . . . . . . . . . . . 355 . 5.18.1 Pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 355 5.18.2 Alternate Functionality Pinout . . . . . . . . . . . . . . . . . . . . . .359 5.18.3 GPIO Pinout Overview . . . . . . . . . . . . . . . . . . . . . . . 3 . 65 5.18.4 Opamp Pinout Overview . . . . . . . . . . . . . . . . . . . . . . . . 365 5.19 EFM32LG942 (TQFP64) . . . . . . . . . . . . . . . . . . . . . . . . .366 5.19.1 Pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 366 5.19.2 Alternate Functionality Pinout . . . . . . . . . . . . . . . . . . . . . .370 5.19.3 GPIO Pinout Overview . . . . . . . . . . . . . . . . . . . . . . . 3 . 75 5.19.4 Opamp Pinout Overview . . . . . . . . . . . . . . . . . . . . . . . . 376 5.20 EFM32LG980 (LQFP100) . . . . . . . . . . . . . . . . . . . . . . . . . 377 5.20.1 Pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 377 5.20.2 Alternate Functionality Pinout . . . . . . . . . . . . . . . . . . . . . .383 5.20.3 GPIO Pinout Overview . . . . . . . . . . . . . . . . . . . . . . . 3 . 92 5.20.4 Opamp Pinout Overview . . . . . . . . . . . . . . . . . . . . . . . . 392 5.21 EFM32LG990 (BGA112) . . . . . . . . . . . . . . . . . . . . . . . . .393 5.21.1 Pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 393 5.21.2 Alternate Functionality Pinout . . . . . . . . . . . . . . . . . . . . . .399 5.21.3 GPIO Pinout Overview . . . . . . . . . . . . . . . . . . . . . . . 4 . 08 5.21.4 Opamp Pinout Overview . . . . . . . . . . . . . . . . . . . . . . . . 408 5.22 EFM32LG995 (BGA120) . . . . . . . . . . . . . . . . . . . . . . . . .409 5.22.1 Pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 409 5.22.2 Alternate Functionality Pinout . . . . . . . . . . . . . . . . . . . . . .415 5.22.3 GPIO Pinout Overview . . . . . . . . . . . . . . . . . . . . . . . 4 . 24 5.22.4 Opamp Pinout Overview . . . . . . . . . . . . . . . . . . . . . . . . 425 6. BGA112 Package Specifications . . . . . . . . . . . . . . . . . . . . . . .426 6.1 BGA112 Package Dimensions . . . . . . . . . . . . . . . . . . . . . . . . 426 6.2 BGA112 PCB Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . 427 6.3 BGA112 Package Marking . . . . . . . . . . . . . . . . . . . . . . . . . 429 7. BGA120 Package Specifications . . . . . . . . . . . . . . . . . . . . . . .430 7.1 BGA120 Package Dimensions . . . . . . . . . . . . . . . . . . . . . . . . 430 7.2 BGA120 PCB Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . 431 7.3 BGA120 Package Marking . . . . . . . . . . . . . . . . . . . . . . . . . 433 8. CSP81 Package Specifications . . . . . . . . . . . . . . . . . . . . . . . . 434 8.1 CSP81 Package Dimensions 8.2 CSP81 PCB Layout . . 8.3 CSP81 Package Marking 8.4 CSP81 Environmental . . . . . . . . . . . . . . . . . . . . . . . . .434 . . . . . . . . . . . . . . . . . . . . . . . . .436 . . . . . . . . . . . . . . . . . . . . . . . . 4 . 39 . . . . . . . . . . . . . . . . . . . . . . . . 4. 39 9. LQFP100 Package Specifications . . . . . . . . . . . . . . . . . . . . . . . 440 silabs.com | Building a more connected world. Rev. 2.40 | 11 9.1 LQFP100 Package Dimensions 9.2 LQFP100 PCB Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 . 42 . . . . . . . . . . . . . . . . . . . . . . . 444 . 9.3 LQFP100 Package Marking 10. QFN64 Package Specifications .440 . . . . . . . . . . . . . . . . . . . . . . .445 10.1 QFN64 Package Dimensions. . . . . . . . . . . . . . . . . . . . . . . . 445 10.2 QFN64 PCB Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . 447 10.3 QFN64 Package Marking . . . . . . . . . . . . . . . . . . . . . . . . . 449 11. TQFP64 Package Specifications . . . . . . . . . . . . . . . . . . . . . . . 450 11.1 TQFP64 Package Dimensions 11.2 TQFP64 PCB Layout . . . . . . . . . . . . . . . . . . . . . . . . .450 . . . . . . . . . . . . . . . . . . . . . . . .452 . . . . . . . . . . . . . . . . . . . . . . . 4. 54 11.3 TQFP64 Package Marking 12. Wafer Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . .455 12.1 Bonding Instructions . 12.2 Wafer Description 12.2.1 Environmental . . . . . . . . . . 12.4 Failure Analysis (FA) Guidelines . . . 13.2 Soldering Information . . . . . . . . . . . . . . . . . . 455 . . . . . . . . . . . . . . . . . . . . . . 456 . . . . . . . . . . . . . . . . . . . . . 456 . 13. Chip Revision, Solder Information, Errata 13.3 Errata . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 . 55 . . . . . . . . . . . . . . . . . . . . . . . . . . .455 12.3 Wafer Storage Guidelines . 13.1 Chip Revision . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .457 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 457 . . .457 . 457 . 14. Revision History. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 458 silabs.com | Building a more connected world. Rev. 2.40 | 12 EFM32LG Data Sheet System Summary 3. System Summary 3.1 System Introduction The EFM32 MCUs are the world’s most energy friendly microcontrollers. With a unique combination of the powerful 32-bit ARM CortexM3, innovative low energy techniques, short wake-up time from energy saving modes, and a wide selection of peripherals, the EFM32LG microcontroller is well suited for any battery operated application as well as other systems requiring high performance and low-energy consumption. This section gives a short introduction to each of the modules in general terms and also shows a summary of the configuration for the EFM32LG devices. For a complete feature set and in-depth information on the modules, refer to the EFM32LG Reference Manual. A block diagram of the EFM32LG is shown in the following figure. Core / Memory ARM CortexTM M3 processor Clock Management Memory Protection Unit Flash Program Memory Debug w/ ETM RAM Memory DMA Controller Energy Management High Frequency Crystal Oscillator High Frequency RC Oscillator Voltage Regulator Voltage Comparator Auxiliary High Freq. RC Osc. Low Freq. RC Oscillator Brown-out Detector Power-on Reset Low Frequency Crystal Oscillator Ultra Low Freq. RC Oscillator Back-up Power Domain Security Hardware AES 32-bit bus Peripheral Reflex System Serial Interfaces USART Low Energy UARTTM I/O Ports Timers and Triggers UART External Bus Interface TFT Driver I2C External Interrupts General Purpose I/O Pin Reset Pin Wakeup USB Timer/Counter LESENSE Low Energy Timer Real Time Counter Pulse Counter Watchdog Timer Analog Interfaces ADC LCD Controller DAC Operational Amplifier Analog Comparator Back-up RTC Lowest power mode with peripheral operational: EM0 - Active EM1 - Sleep EM2 – Deep Sleep EM3 - Stop EM4 - Shutoff Figure 3.1. Block Diagram 3.1.1 ARM Cortex-M3 Core The ARM Cortex-M3 includes a 32-bit RISC processor which can achieve as much as 1.25 Dhrystone MIPS/MHz. A Memory Protection Unit with support for up to 8 memory segments is included, as well as a Wake-up Interrupt Controller handling interrupts triggered while the CPU is asleep. The EFM32 implementation of the Cortex-M3 is described in detail in EFM32LG Reference Manual. 3.1.2 Debug Interface (DBG) This device includes hardware debug support through a 2-pin serial-wire debug interface and an Embedded Trace Module (ETM) for data/instruction tracing. In addition there is also a 1-wire Serial Wire Viewer pin which can be used to output profiling information, data trace and software-generated messages. 3.1.3 Memory System Controller (MSC) The Memory System Controller (MSC) is the program memory unit of the EFM32LG microcontroller. The flash memory is readable and writable from both the Cortex-M3 and DMA. The flash memory is divided into two blocks; the main block and the information block. Program code is normally written to the main block. Additionally, the information block is available for special user data and flash lock bits. There is also a read-only page in the information block containing system and device calibration data. Read and write operations are supported in the energy modes EM0 and EM1. 3.1.4 Direct Memory Access Controller (DMA) The Direct Memory Access (DMA) controller performs memory operations independently of the CPU. This has the benefit of reducing the energy consumption and the workload of the CPU, and enables the system to stay in low energy modes when moving for instance data from the USART to RAM or from the External Bus Interface to a PWM-generating timer. The DMA controller uses the PL230 µDMA controller licensed from ARM. 3.1.5 Reset Management Unit (RMU) The RMU is responsible for handling the reset functionality of the EFM32LG. silabs.com | Building a more connected world. Rev. 2.40 | 13 EFM32LG Data Sheet System Summary 3.1.6 Energy Management Unit (EMU) The Energy Management Unit (EMU) manage all the low energy modes (EM) in EFM32LG microcontrollers. Each energy mode manages if the CPU and the various peripherals are available. The EMU can also be used to turn off the power to unused SRAM blocks. 3.1.7 Clock Management Unit (CMU) The Clock Management Unit (CMU) is responsible for controlling the oscillators and clocks on-board the EFM32LG. The CMU provides the capability to turn on and off the clock on an individual basis to all peripheral modules in addition to enable/disable and configure the available oscillators. The high degree of flexibility enables software to minimize energy consumption in any specific application by not wasting power on peripherals and oscillators that are inactive. 3.1.8 Watchdog (WDOG) The purpose of the watchdog timer is to generate a reset in case of a system failure, to increase application reliability. The failure may e.g. be caused by an external event, such as an ESD pulse, or by a software failure. 3.1.9 Peripheral Reflex System (PRS) The Peripheral Reflex System (PRS) system is a network which lets the different peripheral module communicate directly with each other without involving the CPU. Peripheral modules which send out Reflex signals are called producers. The PRS routes these reflex signals to consumer peripherals which apply actions depending on the data received. The format for the Reflex signals is not given, but edge triggers and other functionality can be applied by the PRS. 3.1.10 External Bus Interface (EBI) The External Bus Interface provides access to external parallel interface devices such as SRAM, FLASH, ADCs and LCDs. The interface is memory mapped into the address bus of the Cortex-M3. This enables seamless access from software without manually manipulating the IO settings each time a read or write is performed. The data and address lines are multiplexed in order to reduce the number of pins required to interface the external devices. The timing is adjustable to meet specifications of the external devices. The interface is limited to asynchronous devices. 3.1.11 TFT Direct Drive The EBI contains a TFT controller which can drive a TFT via a 565 RGB interface. The TFT controller supports programmable display and port sizes and offers accurate control of frequency and setup and hold timing. Direct Drive is supported for TFT displays which do not have their own frame buffer. In that case TFT Direct Drive can transfer data from either on-chip memory or from an external memory device to the TFT at low CPU load. Automatic alpha-blending and masking is also supported for transfers through the EBI interface. 3.1.12 Universal Serial Bus Controller (USB) The USB is a full-speed USB 2.0 compliant OTG host/device controller. The USB can be used in Device, On-the-Go (OTG) Dual Role Device, or Host-only configuration. In OTG mode, the USB supports both Host Negotiation Protocol (HNP) and Session Request Protocol (SRP). The device supports both full-speed (12 Mbit/s) and low-speed (1.5 Mbit/s) operation. The USB device includes an internal, dedicated Descriptor-Based Scatter/Gather DMA and supports up to 6 OUT endpoints and 6 IN endpoints, in addition to endpoint 0. The on-chip PHY includes all OTG features, except for the voltage booster for supplying 5V to VBUS when operating as a host. 3.1.13 Inter-Integrated Circuit Interface (I2C) The I2C module provides an interface between the MCU and a serial I2C-bus. It is capable of acting as both a leader and a follower, and supports multi-leader buses. Both standard-mode, fast-mode and fastmode plus speeds are supported, allowing transmission rates all the way from 10 kbit/s up to 1 Mbit/s. Follower arbitration and timeouts are also provided to allow implementation of an SMBus compliant system. The interface provided to software by the I2C module, allows both fine-grained control of the transmission process and close to automatic transfers. Automatic recognition of follower addresses is provided in all energy modes. 3.1.14 Universal Synchronous/Asynchronous Receiver/Transmitter (USART) The Universal Synchronous Asynchronous serial Receiver and Transmitter (USART) is a very flexible serial I/O module. It supports full duplex asynchronous UART communication as well as RS-485, SPI, MicroWire and 3-wire. It can also interface with ISO7816 SmartCards, IrDA, and I2S devices. silabs.com | Building a more connected world. Rev. 2.40 | 14 EFM32LG Data Sheet System Summary 3.1.15 Pre-Programmed USB/UART Bootloader The bootloader presented in application note, AN0042: USB/UART Bootloader, is pre-programmed in the device at factory. The bootloader enables users to program the EFM32 through a UART or a USB CDC class virtual UART without the need for a debugger. The autobaud feature, interface, and commands are described further in the application note. 3.1.16 Universal Asynchronous Receiver/Transmitter (UART) The Universal Asynchronous serial Receiver and Transmitter (UART) is a very flexible serial I/O module. It supports full- and half-duplex asynchronous UART communication. 3.1.17 Low Energy Universal Asynchronous Receiver/Transmitter (LEUART) The unique LEUARTTM, the Low Energy UART, is a UART that allows two-way UART communication on a strict power budget. Only a 32.768 kHz clock is needed to allow UART communication up to 9600 baud/ s. The LEUART includes all necessary hardware support to make asynchronous serial communication possible with minimum of software intervention and energy consumption. 3.1.18 Timer/Counter (TIMER) The 16-bit general purpose timer has three compare/capture channels for input capture and compare/Pulse-Width Modulation (PWM) output. TIMER0 also includes a Dead-Time Insertion module suitable for motor control applications. 3.1.19 Real Time Counter (RTC) The Real Time Counter (RTC) contains a 24-bit counter and is clocked either by a 32.768 kHz crystal oscillator, or a 32.768 kHz RC oscillator. In addition to energy modes EM0 and EM1, the RTC is also available in EM2. This makes it ideal for keeping track of time since the RTC is enabled in EM2 where most of the device is powered down. 3.1.20 Backup Real Time Counter (BURTC) The Backup Real Time Counter (BURTC) contains a 32-bit counter and is clocked either by a 32.768 kHz crystal oscillator, a 32.768 kHz RC oscillator or a 1 kHz ULFRCO. The BURTC is available in all Energy Modes and it can also run in backup mode, making it operational even if the main power should drain out. 3.1.21 Low Energy Timer (LETIMER) The unique LETIMERTM, the Low Energy Timer, is a 16-bit timer that is available in energy mode EM2 in addition to EM1 and EM0. Because of this, it can be used for timing and output generation when most of the device is powered down, allowing simple tasks to be performed while the power consumption of the system is kept at an absolute minimum. The LETIMER can be used to output a variety of waveforms with minimal software intervention. It is also connected to the Real Time Counter (RTC), and can be configured to start counting on compare matches from the RTC. 3.1.22 Pulse Counter (PCNT) The Pulse Counter (PCNT) can be used for counting pulses on a single input or to decode quadrature encoded inputs. It runs off either the internal LFACLK or the PCNTn_S0IN pin as external clock source. The module may operate in energy mode EM0 - EM3. 3.1.23 Analog Comparator (ACMP) The Analog Comparator is used to compare the voltage of two analog inputs, with a digital output indicating which input voltage is higher. Inputs can either be one of the selectable internal references or from external pins. Response time and thereby also the current consumption can be configured by altering the current supply to the comparator. 3.1.24 Voltage Comparator (VCMP) The Voltage Supply Comparator is used to monitor the supply voltage from software. An interrupt can be generated when the supply falls below or rises above a programmable threshold. Response time and thereby also the current consumption can be configured by altering the current supply to the comparator. silabs.com | Building a more connected world. Rev. 2.40 | 15 EFM32LG Data Sheet System Summary 3.1.25 Analog to Digital Converter (ADC) The ADC is a Successive Approximation Register (SAR) architecture, with a resolution of up to 12 bits at up to one million samples per second. The integrated input mux can select inputs from 8 external pins and 6 internal signals. 3.1.26 Digital to Analog Converter (DAC) The Digital to Analog Converter (DAC) can convert a digital value to an analog output voltage. The DAC is fully differential rail-to-rail, with 12-bit resolution. It has two single-ended output buffers which can be combined into one differential output. The DAC may be used for a number of different applications such as sensor interfaces or sound output. 3.1.27 Operational Amplifier (OPAMP) The EFM32LG features up to three Operational Amplifiers. The Operational Amplifier is a versatile general purpose amplifier with railto-rail differential input and rail-to-rail single-ended output. The input can be set to pin, DAC or OPAMP, whereas the output can be pin, OPAMP or ADC. The current is programmable and the OPAMP has various internal configurations such as unity gain, programmable gain using internal resistors etc. 3.1.28 Low Energy Sensor Interface (LESENSE) The Low Energy Sensor Interface (LESENSETM), is a highly configurable sensor interface with support for up to 16 individually configurable sensors. By controlling the analog comparators and DAC, LESENSE is capable of supporting a wide range of sensors and measurement schemes, and can for instance measure LC sensors, resistive sensors and capacitive sensors. LESENSE also includes a programmable FSM which enables simple processing of measurement results without CPU intervention. LESENSE is available in energy mode EM2, in addition to EM0 and EM1, making it ideal for sensor monitoring in applications with a strict energy budget. 3.1.29 Backup Power Domain The backup power domain is a separate power domain containing a Backup Real Time Counter, BURTC, and a set of retention registers, available in all energy modes. This power domain can be configured to automatically change power source to a backup battery when the main power drains out. The backup power domain enables the EFM32LG to keep track of time and retain data, even if the main power source should drain out. 3.1.30 Advanced Encryption Standard Accelerator (AES) The AES accelerator performs AES encryption and decryption with 128-bit or 256-bit keys. Encrypting or decrypting one 128-bit data block takes 52 HFCORECLK cycles with 128-bit keys and 75 HFCORECLK cycles with 256-bit keys. The AES module is an AHB subordinate which enables efficient access to the data and key registers. All write accesses to the AES module must be 32-bit operations, i.e. 8- or 16-bit operations are not supported. 3.1.31 General Purpose Input/Output (GPIO) In the EFM32LG, there are up to 93 General Purpose Input/Output (GPIO) pins, which are divided into ports with up to 16 pins each. These pins can individually be configured as either an output or input. More advanced configurations like open-drain, filtering and drive strength can also be configured individually for the pins. The GPIO pins can also be overridden by peripheral pin connections, like Timer PWM outputs or USART communication, which can be routed to several locations on the device. The GPIO supports up to 16 asynchronous external pin interrupts, which enables interrupts from any pin on the device. Also, the input value of a pin can be routed through the Peripheral Reflex System to other peripherals. 3.1.32 Liquid Crystal Display Driver (LCD) The LCD driver is capable of driving a segmented LCD display with up to 8x36 segments. A voltage boost function enables it to provide the LCD display with higher voltage than the supply voltage for the device. In addition, an animation feature can run custom animations on the LCD display without any CPU intervention. The LCD driver can also remain active even in Energy Mode 2 and provides a Frame Counter interrupt that can wake-up the device on a regular basis for updating data. 3.2 Configuration Summary The following sections provide device-specific features of the EFM32LG family of MCUs. These features are subsets of the full feature set described in the EFM32LG Reference Manual. silabs.com | Building a more connected world. Rev. 2.40 | 16 EFM32LG Data Sheet System Summary 3.2.1 EFM32LG230 The following table describes device-specific implementation of the EFM32LG230 features. Table 3.1. EFM32LG230 Configuration Summary Module Configuration Pin Connections Cortex-M3 Full configuration NA DBG Full configuration DBG_SWCLK, DBG_SWDIO, DBG_SWO MSC Full configuration NA DMA Full configuration NA RMU Full configuration NA EMU Full configuration NA CMU Full configuration CMU_OUT0, CMU_OUT1 WDOG Full configuration NA PRS Full configuration NA I2C0 Full configuration I2C0_SDA, I2C0_SCL I2C1 Full configuration I2C1_SDA, I2C1_SCL USART0 Full configuration with IrDA US0_TX, US0_RX. US0_CLK, US0_CS USART1 Full configuration with I2S US1_TX, US1_RX, US1_CLK, US1_CS USART2 Full configuration with I2S US2_TX, US2_RX, US2_CLK, US2_CS LEUART0 Full configuration LEU0_TX, LEU0_RX LEUART1 Full configuration LEU1_TX, LEU1_RX TIMER0 Full configuration with DTI TIM0_CC[2:0], TIM0_CDTI[2:0] TIMER1 Full configuration TIM1_CC[2:0] TIMER2 Full configuration TIM2_CC[2:0] TIMER3 Full configuration TIM3_CC[2:0] RTC Full configuration NA BURTC Full configuration NA LETIMER0 Full configuration LET0_O[1:0] PCNT0 Full configuration, 16-bit count register PCNT0_S[1:0] PCNT1 Full configuration, 8-bit count register PCNT1_S[1:0] PCNT2 Full configuration, 8-bit count register PCNT2_S[1:0] ACMP0 Full configuration ACMP0_CH[7:0], ACMP0_O ACMP1 Full configuration ACMP1_CH[7:0], ACMP1_O VCMP Full configuration NA ADC0 Full configuration ADC0_CH[7:0] DAC0 Full configuration DAC0_OUT[1:0], DAC0_OUTxALT OPAMP Full configuration Outputs: OPAMP_OUTx, OPAMP_OUTxALT, Inputs: OPAMP_Px, OPAMP_Nx AES Full configuration NA silabs.com | Building a more connected world. Rev. 2.40 | 17 EFM32LG Data Sheet System Summary Module Configuration Pin Connections GPIO 56 pins Available pins are shown in 5.1.3 GPIO Pinout Overview silabs.com | Building a more connected world. Rev. 2.40 | 18 EFM32LG Data Sheet System Summary 3.2.2 EFM32LG232 The following table describes device-specific implementation of the EFM32LG232 features. Table 3.2. EFM32LG232 Configuration Summary Module Configuration Pin Connections Cortex-M3 Full configuration NA DBG Full configuration DBG_SWCLK, DBG_SWDIO, DBG_SWO MSC Full configuration NA DMA Full configuration NA RMU Full configuration NA EMU Full configuration NA CMU Full configuration CMU_OUT0, CMU_OUT1 WDOG Full configuration NA PRS Full configuration NA I2C0 Full configuration I2C0_SDA, I2C0_SCL I2C1 Full configuration I2C1_SDA, I2C1_SCL USART0 Full configuration with IrDA US0_TX, US0_RX. US0_CLK, US0_CS USART1 Full configuration with I2S US1_TX, US1_RX, US1_CLK, US1_CS USART2 Full configuration with I2S US2_TX, US2_RX, US2_CLK, US2_CS LEUART0 Full configuration LEU0_TX, LEU0_RX LEUART1 Full configuration LEU1_TX, LEU1_RX TIMER0 Full configuration with DTI TIM0_CC[2:0], TIM0_CDTI[2:0] TIMER1 Full configuration TIM1_CC[2:0] TIMER2 Full configuration TIM2_CC[2:0] TIMER3 Full configuration TIM3_CC[2:0] RTC Full configuration NA BURTC Full configuration NA LETIMER0 Full configuration LET0_O[1:0] PCNT0 Full configuration, 16-bit count register PCNT0_S[1:0] PCNT1 Full configuration, 8-bit count register PCNT1_S[1:0] PCNT2 Full configuration, 8-bit count register PCNT2_S[1:0] ACMP0 Full configuration ACMP0_CH[7:0], ACMP0_O ACMP1 Full configuration ACMP1_CH[7:0], ACMP1_O VCMP Full configuration NA ADC0 Full configuration ADC0_CH[7:0] DAC0 Full configuration DAC0_OUT[1:0], DAC0_OUTxALT OPAMP Full configuration Outputs: OPAMP_OUTx, OPAMP_OUTxALT, Inputs: OPAMP_Px, OPAMP_Nx AES Full configuration NA silabs.com | Building a more connected world. Rev. 2.40 | 19 EFM32LG Data Sheet System Summary Module Configuration Pin Connections GPIO 53 pins Available pins are shown in 5.2.3 GPIO Pinout Overview silabs.com | Building a more connected world. Rev. 2.40 | 20 EFM32LG Data Sheet System Summary 3.2.3 EFM32LG280 The following table describes device-specific implementation of the EFM32LG280 features. Table 3.3. EFM32LG280 Configuration Summary Module Configuration Pin Connections Cortex-M3 Full configuration NA DBG Full configuration DBG_SWCLK, DBG_SWDIO, DBG_SWO MSC Full configuration NA DMA Full configuration NA RMU Full configuration NA EMU Full configuration NA CMU Full configuration CMU_OUT0, CMU_OUT1 WDOG Full configuration NA PRS Full configuration NA EBI Full configuration EBI_A[27:0], EBI_AD[15:0], EBI_ARDY, EBI_ALE, EBI_BL[1:0], EBI_CS[3:0], EBI_CSTFT, EBI_DCLK, EBI_DTEN, EBI_HSNC, EBI_NANDREn, EBI_NANDWEn, EBI_REn, EBI_VSNC, EBI_WEn I2C0 Full configuration I2C0_SDA, I2C0_SCL I2C1 Full configuration I2C1_SDA, I2C1_SCL USART0 Full configuration with IrDA US0_TX, US0_RX. US0_CLK, US0_CS USART1 Full configuration with I2S US1_TX, US1_RX, US1_CLK, US1_CS USART2 Full configuration with I2S US2_TX, US2_RX, US2_CLK, US2_CS UART0 Full configuration U0_TX, U0_RX UART1 Full configuration U1_TX, U1_RX LEUART0 Full configuration LEU0_TX, LEU0_RX LEUART1 Full configuration LEU1_TX, LEU1_RX TIMER0 Full configuration with DTI TIM0_CC[2:0], TIM0_CDTI[2:0] TIMER1 Full configuration TIM1_CC[2:0] TIMER2 Full configuration TIM2_CC[2:0] TIMER3 Full configuration TIM3_CC[2:0] RTC Full configuration NA BURTC Full configuration NA LETIMER0 Full configuration LET0_O[1:0] PCNT0 Full configuration, 16-bit count register PCNT0_S[1:0] PCNT1 Full configuration, 8-bit count register PCNT1_S[1:0] PCNT2 Full configuration, 8-bit count register PCNT2_S[1:0] ACMP0 Full configuration ACMP0_CH[7:0], ACMP0_O ACMP1 Full configuration ACMP1_CH[7:0], ACMP1_O VCMP Full configuration NA silabs.com | Building a more connected world. Rev. 2.40 | 21 EFM32LG Data Sheet System Summary Module Configuration Pin Connections ADC0 Full configuration ADC0_CH[7:0] DAC0 Full configuration DAC0_OUT[1:0], DAC0_OUTxALT OPAMP Full configuration Outputs: OPAMP_OUTx, OPAMP_OUTxALT, Inputs: OPAMP_Px, OPAMP_Nx AES Full configuration NA GPIO 85 pins Available pins are shown in 5.3.3 GPIO Pinout Overview silabs.com | Building a more connected world. Rev. 2.40 | 22 EFM32LG Data Sheet System Summary 3.2.4 EFM32LG290 The following table describes device-specific implementation of the EFM32LG290 features. Table 3.4. EFM32LG290 Configuration Summary Module Configuration Pin Connections Cortex-M3 Full configuration NA DBG Full configuration DBG_SWCLK, DBG_SWDIO, DBG_SWO MSC Full configuration NA DMA Full configuration NA RMU Full configuration NA EMU Full configuration NA CMU Full configuration CMU_OUT0, CMU_OUT1 WDOG Full configuration NA PRS Full configuration NA EBI Full configuration EBI_A[27:0], EBI_AD[15:0], EBI_ARDY, EBI_ALE, EBI_BL[1:0], EBI_CS[3:0], EBI_CSTFT, EBI_DCLK, EBI_DTEN, EBI_HSNC, EBI_NANDREn, EBI_NANDWEn, EBI_REn, EBI_VSNC, EBI_WEn I2C0 Full configuration I2C0_SDA, I2C0_SCL I2C1 Full configuration I2C1_SDA, I2C1_SCL USART0 Full configuration with IrDA US0_TX, US0_RX. US0_CLK, US0_CS USART1 Full configuration with I2S US1_TX, US1_RX, US1_CLK, US1_CS USART2 Full configuration with I2S US2_TX, US2_RX, US2_CLK, US2_CS UART0 Full configuration U0_TX, U0_RX UART1 Full configuration U1_TX, U1_RX LEUART0 Full configuration LEU0_TX, LEU0_RX LEUART1 Full configuration LEU1_TX, LEU1_RX TIMER0 Full configuration with DTI TIM0_CC[2:0], TIM0_CDTI[2:0] TIMER1 Full configuration TIM1_CC[2:0] TIMER2 Full configuration TIM2_CC[2:0] TIMER3 Full configuration TIM3_CC[2:0] RTC Full configuration NA BURTC Full configuration NA LETIMER0 Full configuration LET0_O[1:0] PCNT0 Full configuration, 16-bit count register PCNT0_S[1:0] PCNT1 Full configuration, 8-bit count register PCNT1_S[1:0] PCNT2 Full configuration, 8-bit count register PCNT2_S[1:0] ACMP0 Full configuration ACMP0_CH[7:0], ACMP0_O ACMP1 Full configuration ACMP1_CH[7:0], ACMP1_O VCMP Full configuration NA silabs.com | Building a more connected world. Rev. 2.40 | 23 EFM32LG Data Sheet System Summary Module Configuration Pin Connections ADC0 Full configuration ADC0_CH[7:0] DAC0 Full configuration DAC0_OUT[1:0], DAC0_OUTxALT OPAMP Full configuration Outputs: OPAMP_OUTx, OPAMP_OUTxALT, Inputs: OPAMP_Px, OPAMP_Nx AES Full configuration NA GPIO 90 pins Available pins are shown in 5.4.3 GPIO Pinout Overview silabs.com | Building a more connected world. Rev. 2.40 | 24 EFM32LG Data Sheet System Summary 3.2.5 EFM32LG295 The following table describes device-specific implementation of the EFM32LG295 features. Table 3.5. EFM32LG295 Configuration Summary Module Configuration Pin Connections Cortex-M3 Full configuration NA DBG Full configuration DBG_SWCLK, DBG_SWDIO, DBG_SWO MSC Full configuration NA DMA Full configuration NA RMU Full configuration NA EMU Full configuration NA CMU Full configuration CMU_OUT0, CMU_OUT1 WDOG Full configuration NA PRS Full configuration NA EBI Full configuration EBI_A[27:0], EBI_AD[15:0], EBI_ARDY, EBI_ALE, EBI_BL[1:0], EBI_CS[3:0], EBI_CSTFT, EBI_DCLK, EBI_DTEN, EBI_HSNC, EBI_NANDREn, EBI_NANDWEn, EBI_REn, EBI_VSNC, EBI_WEn I2C0 Full configuration I2C0_SDA, I2C0_SCL I2C1 Full configuration I2C1_SDA, I2C1_SCL USART0 Full configuration with IrDA US0_TX, US0_RX. US0_CLK, US0_CS USART1 Full configuration with I2S US1_TX, US1_RX, US1_CLK, US1_CS USART2 Full configuration with I2S US2_TX, US2_RX, US2_CLK, US2_CS UART0 Full configuration U0_TX, U0_RX UART1 Full configuration U1_TX, U1_RX LEUART0 Full configuration LEU0_TX, LEU0_RX LEUART1 Full configuration LEU1_TX, LEU1_RX TIMER0 Full configuration with DTI TIM0_CC[2:0], TIM0_CDTI[2:0] TIMER1 Full configuration TIM1_CC[2:0] TIMER2 Full configuration TIM2_CC[2:0] TIMER3 Full configuration TIM3_CC[2:0] RTC Full configuration NA BURTC Full configuration NA LETIMER0 Full configuration LET0_O[1:0] PCNT0 Full configuration, 16-bit count register PCNT0_S[1:0] PCNT1 Full configuration, 8-bit count register PCNT1_S[1:0] PCNT2 Full configuration, 8-bit count register PCNT2_S[1:0] ACMP0 Full configuration ACMP0_CH[7:0], ACMP0_O ACMP1 Full configuration ACMP1_CH[7:0], ACMP1_O VCMP Full configuration NA silabs.com | Building a more connected world. Rev. 2.40 | 25 EFM32LG Data Sheet System Summary Module Configuration Pin Connections ADC0 Full configuration ADC0_CH[7:0] DAC0 Full configuration DAC0_OUT[1:0], DAC0_OUTxALT OPAMP Full configuration Outputs: OPAMP_OUTx, OPAMP_OUTxALT, Inputs: OPAMP_Px, OPAMP_Nx AES Full configuration NA GPIO 93 pins Available pins are shown in 5.5.3 GPIO Pinout Overview silabs.com | Building a more connected world. Rev. 2.40 | 26 EFM32LG Data Sheet System Summary 3.2.6 EFM32LG330 The following table describes device-specific implementation of the EFM32LG330 features. Table 3.6. EFM32LG330 Configuration Summary Module Configuration Pin Connections Cortex-M3 Full configuration NA DBG Full configuration DBG_SWCLK, DBG_SWDIO, DBG_SWO MSC Full configuration NA DMA Full configuration NA RMU Full configuration NA EMU Full configuration NA CMU Full configuration CMU_OUT0, CMU_OUT1 WDOG Full configuration NA PRS Full configuration NA USB Full configuration USB_VBUS, USB_VBUSEN, USB_VREGI, USB_VREGO, USB_DM, USB_DMPU, USB_DP, USB_ID I2C0 Full configuration I2C0_SDA, I2C0_SCL I2C1 Full configuration I2C1_SDA, I2C1_SCL USART0 Full configuration with IrDA US0_TX, US0_RX. US0_CLK, US0_CS USART1 Full configuration with I2S US1_TX, US1_RX, US1_CLK, US1_CS USART2 Full configuration with I2S US2_TX, US2_RX, US2_CLK, US2_CS LEUART0 Full configuration LEU0_TX, LEU0_RX LEUART1 Full configuration LEU1_TX, LEU1_RX TIMER0 Full configuration with DTI TIM0_CC[2:0], TIM0_CDTI[2:0] TIMER1 Full configuration TIM1_CC[2:0] TIMER2 Full configuration TIM2_CC[2:0] TIMER3 Full configuration TIM3_CC[2:0] RTC Full configuration NA BURTC Full configuration NA LETIMER0 Full configuration LET0_O[1:0] PCNT0 Full configuration, 16-bit count register PCNT0_S[1:0] PCNT1 Full configuration, 8-bit count register PCNT1_S[1:0] PCNT2 Full configuration, 8-bit count register PCNT2_S[1:0] ACMP0 Full configuration ACMP0_CH[7:0], ACMP0_O ACMP1 Full configuration ACMP1_CH[3:0], ACMP1_O VCMP Full configuration NA ADC0 Full configuration ADC0_CH[7:0] DAC0 Full configuration DAC0_OUT[1:0], DAC0_OUTxALT silabs.com | Building a more connected world. Rev. 2.40 | 27 EFM32LG Data Sheet System Summary Module Configuration Pin Connections OPAMP Full configuration Outputs: OPAMP_OUTx, OPAMP_OUTxALT, Inputs: OPAMP_Px, OPAMP_Nx AES Full configuration NA GPIO 53 pins Available pins are shown in 5.6.3 GPIO Pinout Overview silabs.com | Building a more connected world. Rev. 2.40 | 28 EFM32LG Data Sheet System Summary 3.2.7 EFM32LG332 The following table describes device-specific implementation of the EFM32LG332 features. Table 3.7. EFM32LG332 Configuration Summary Module Configuration Pin Connections Cortex-M3 Full configuration NA DBG Full configuration DBG_SWCLK, DBG_SWDIO, DBG_SWO MSC Full configuration NA DMA Full configuration NA RMU Full configuration NA EMU Full configuration NA CMU Full configuration CMU_OUT0, CMU_OUT1 WDOG Full configuration NA PRS Full configuration NA USB Full configuration USB_VBUS, USB_VBUSEN, USB_VREGI, USB_VREGO, USB_DM, USB_DMPU, USB_DP, USB_ID I2C0 Full configuration I2C0_SDA, I2C0_SCL I2C1 Full configuration I2C1_SDA, I2C1_SCL USART0 Full configuration with IrDA US0_TX, US0_RX. US0_CLK, US0_CS USART1 Full configuration with I2S US1_TX, US1_RX, US1_CLK, US1_CS USART2 Full configuration with I2S US2_TX, US2_RX, US2_CLK, US2_CS LEUART0 Full configuration LEU0_TX, LEU0_RX LEUART1 Full configuration LEU1_TX, LEU1_RX TIMER0 Full configuration with DTI TIM0_CC[2:0], TIM0_CDTI[2:0] TIMER1 Full configuration TIM1_CC[2:0] TIMER2 Full configuration TIM2_CC[2:0] TIMER3 Full configuration TIM3_CC[2:0] RTC Full configuration NA BURTC Full configuration NA LETIMER0 Full configuration LET0_O[1:0] PCNT0 Full configuration, 16-bit count register PCNT0_S[1:0] PCNT1 Full configuration, 8-bit count register PCNT1_S[1:0] PCNT2 Full configuration, 8-bit count register PCNT2_S[1:0] ACMP0 Full configuration ACMP0_CH[7:0], ACMP0_O ACMP1 Full configuration ACMP1_CH[3:0], ACMP1_O VCMP Full configuration NA ADC0 Full configuration ADC0_CH[7:0] DAC0 Full configuration DAC0_OUT[1:0], DAC0_OUTxALT silabs.com | Building a more connected world. Rev. 2.40 | 29 EFM32LG Data Sheet System Summary Module Configuration Pin Connections OPAMP Full configuration Outputs: OPAMP_OUTx, OPAMP_OUTxALT, Inputs: OPAMP_Px, OPAMP_Nx AES Full configuration NA GPIO 50 pins Available pins are shown in 5.7.3 GPIO Pinout Overview silabs.com | Building a more connected world. Rev. 2.40 | 30 EFM32LG Data Sheet System Summary 3.2.8 EFM32LG360 The following table describes device-specific implementation of the EFM32LG360 features. Table 3.8. EFM32LG360 Configuration Summary Module Configuration Pin Connections Cortex-M3 Full configuration NA DBG Full configuration DBG_SWCLK, DBG_SWDIO, DBG_SWO MSC Full configuration NA DMA Full configuration NA RMU Full configuration NA EMU Full configuration NA CMU Full configuration CMU_OUT0, CMU_OUT1 WDOG Full configuration NA PRS Full configuration NA USB Full configuration USB_VBUS, USB_VBUSEN, USB_VREGI, USB_VREGO, USB_DM, USB_DMPU, USB_DP, USB_ID I2C0 Full configuration I2C0_SDA, I2C0_SCL I2C1 Full configuration I2C1_SDA, I2C1_SCL USART0 Full configuration with IrDA US0_TX, US0_RX. US0_CLK, US0_CS USART1 Full configuration with I2S US1_TX, US1_RX, US1_CLK, US1_CS USART2 Full configuration with I2S US2_TX, US2_RX, US2_CLK, US2_CS UART0 Full configuration U0_TX, U0_RX UART1 Full configuration U1_TX, U1_RX LEUART0 Full configuration LEU0_TX, LEU0_RX LEUART1 Full configuration LEU1_TX, LEU1_RX TIMER0 Full configuration with DTI TIM0_CC[2:0], TIM0_CDTI[2:0] TIMER1 Full configuration TIM1_CC[2:0] TIMER2 Full configuration TIM2_CC[2:0] TIMER3 Full configuration TIM3_CC[2:0] RTC Full configuration NA BURTC Full configuration NA LETIMER0 Full configuration LET0_O[1:0] PCNT0 Full configuration, 16-bit count register PCNT0_S[1:0] PCNT1 Full configuration, 8-bit count register PCNT1_S[1:0] PCNT2 Full configuration, 8-bit count register PCNT2_S[1:0] ACMP0 Full configuration ACMP0_CH[7:0], ACMP0_O ACMP1 Full configuration ACMP1_CH[7:0], ACMP1_O VCMP Full configuration NA ADC0 Full configuration ADC0_CH[7:0] silabs.com | Building a more connected world. Rev. 2.40 | 31 EFM32LG Data Sheet System Summary Module Configuration Pin Connections DAC0 Full configuration DAC0_OUT[1:0], DAC0_OUTxALT OPAMP Full configuration Outputs: OPAMP_OUTx, OPAMP_OUTxALT, Inputs: OPAMP_Px, OPAMP_Nx AES Full configuration NA GPIO 65 pins Available pins are shown in 5.8.3 GPIO Pinout Overview silabs.com | Building a more connected world. Rev. 2.40 | 32 EFM32LG Data Sheet System Summary 3.2.9 EFM32LG380 The following table describes device-specific implementation of the EFM32LG380 features. Table 3.9. EFM32LG380 Configuration Summary Module Configuration Pin Connections Cortex-M3 Full configuration NA DBG Full configuration DBG_SWCLK, DBG_SWDIO, DBG_SWO MSC Full configuration NA DMA Full configuration NA RMU Full configuration NA EMU Full configuration NA CMU Full configuration CMU_OUT0, CMU_OUT1 WDOG Full configuration NA PRS Full configuration NA USB Full configuration USB_VBUS, USB_VBUSEN, USB_VREGI, USB_VREGO, USB_DM, USB_DMPU, USB_DP, USB_ID EBI Full configuration EBI_A[27:0], EBI_AD[15:0], EBI_ARDY, EBI_ALE, EBI_BL[1:0], EBI_CS[3:0], EBI_CSTFT, EBI_DCLK, EBI_DTEN, EBI_HSNC, EBI_NANDREn, EBI_NANDWEn, EBI_REn, EBI_VSNC, EBI_WEn I2C0 Full configuration I2C0_SDA, I2C0_SCL I2C1 Full configuration I2C1_SDA, I2C1_SCL USART0 Full configuration with IrDA US0_TX, US0_RX. US0_CLK, US0_CS USART1 Full configuration with I2S US1_TX, US1_RX, US1_CLK, US1_CS USART2 Full configuration with I2S US2_TX, US2_RX, US2_CLK, US2_CS UART0 Full configuration U0_TX, U0_RX UART1 Full configuration U1_TX, U1_RX LEUART0 Full configuration LEU0_TX, LEU0_RX LEUART1 Full configuration LEU1_TX, LEU1_RX TIMER0 Full configuration with DTI TIM0_CC[2:0], TIM0_CDTI[2:0] TIMER1 Full configuration TIM1_CC[2:0] TIMER2 Full configuration TIM2_CC[2:0] TIMER3 Full configuration TIM3_CC[2:0] RTC Full configuration NA BURTC Full configuration NA LETIMER0 Full configuration LET0_O[1:0] PCNT0 Full configuration, 16-bit count register PCNT0_S[1:0] PCNT1 Full configuration, 8-bit count register PCNT1_S[1:0] PCNT2 Full configuration, 8-bit count register PCNT2_S[1:0] ACMP0 Full configuration ACMP0_CH[7:0], ACMP0_O silabs.com | Building a more connected world. Rev. 2.40 | 33 EFM32LG Data Sheet System Summary Module Configuration Pin Connections ACMP1 Full configuration ACMP1_CH[3:0], ACMP1_O VCMP Full configuration NA ADC0 Full configuration ADC0_CH[7:0] DAC0 Full configuration DAC0_OUT[1:0], DAC0_OUTxALT OPAMP Full configuration Outputs: OPAMP_OUTx, OPAMP_OUTxALT, Inputs: OPAMP_Px, OPAMP_Nx AES Full configuration NA GPIO 83 pins Available pins are shown in 5.9.3 GPIO Pinout Overview silabs.com | Building a more connected world. Rev. 2.40 | 34 EFM32LG Data Sheet System Summary 3.2.10 EFM32LG390 The following table describes device-specific implementation of the EFM32LG390 features. Table 3.10. EFM32LG390 Configuration Summary Module Configuration Pin Connections Cortex-M3 Full configuration NA DBG Full configuration DBG_SWCLK, DBG_SWDIO, DBG_SWO MSC Full configuration NA DMA Full configuration NA RMU Full configuration NA EMU Full configuration NA CMU Full configuration CMU_OUT0, CMU_OUT1 WDOG Full configuration NA PRS Full configuration NA USB Full configuration USB_VBUS, USB_VBUSEN, USB_VREGI, USB_VREGO, USB_DM, USB_DMPU, USB_DP, USB_ID EBI Full configuration EBI_A[27:0], EBI_AD[15:0], EBI_ARDY, EBI_ALE, EBI_BL[1:0], EBI_CS[3:0], EBI_CSTFT, EBI_DCLK, EBI_DTEN, EBI_HSNC, EBI_NANDREn, EBI_NANDWEn, EBI_REn, EBI_VSNC, EBI_WEn I2C0 Full configuration I2C0_SDA, I2C0_SCL I2C1 Full configuration I2C1_SDA, I2C1_SCL USART0 Full configuration with IrDA US0_TX, US0_RX. US0_CLK, US0_CS USART1 Full configuration with I2S US1_TX, US1_RX, US1_CLK, US1_CS USART2 Full configuration with I2S US2_TX, US2_RX, US2_CLK, US2_CS UART0 Full configuration U0_TX, U0_RX UART1 Full configuration U1_TX, U1_RX LEUART0 Full configuration LEU0_TX, LEU0_RX LEUART1 Full configuration LEU1_TX, LEU1_RX TIMER0 Full configuration with DTI TIM0_CC[2:0], TIM0_CDTI[2:0] TIMER1 Full configuration TIM1_CC[2:0] TIMER2 Full configuration TIM2_CC[2:0] TIMER3 Full configuration TIM3_CC[2:0] RTC Full configuration NA BURTC Full configuration NA LETIMER0 Full configuration LET0_O[1:0] PCNT0 Full configuration, 16-bit count register PCNT0_S[1:0] PCNT1 Full configuration, 8-bit count register PCNT1_S[1:0] PCNT2 Full configuration, 8-bit count register PCNT2_S[1:0] ACMP0 Full configuration ACMP0_CH[7:0], ACMP0_O silabs.com | Building a more connected world. Rev. 2.40 | 35 EFM32LG Data Sheet System Summary Module Configuration Pin Connections ACMP1 Full configuration ACMP1_CH[3:0], ACMP1_O VCMP Full configuration NA ADC0 Full configuration ADC0_CH[7:0] DAC0 Full configuration DAC0_OUT[1:0], DAC0_OUTxALT OPAMP Full configuration Outputs: OPAMP_OUTx, OPAMP_OUTxALT, Inputs: OPAMP_Px, OPAMP_Nx AES Full configuration NA GPIO 86 pins Available pins are shown in 5.10.3 GPIO Pinout Overview silabs.com | Building a more connected world. Rev. 2.40 | 36 EFM32LG Data Sheet System Summary 3.2.11 EFM32LG395 The following table describes device-specific implementation of the EFM32LG395 features. Table 3.11. EFM32LG395 Configuration Summary Module Configuration Pin Connections Cortex-M3 Full configuration NA DBG Full configuration DBG_SWCLK, DBG_SWDIO, DBG_SWO MSC Full configuration NA DMA Full configuration NA RMU Full configuration NA EMU Full configuration NA CMU Full configuration CMU_OUT0, CMU_OUT1 WDOG Full configuration NA PRS Full configuration NA USB Full configuration USB_VBUS, USB_VBUSEN, USB_VREGI, USB_VREGO, USB_DM, USB_DMPU, USB_DP, USB_ID EBI Full configuration EBI_A[27:0], EBI_AD[15:0], EBI_ARDY, EBI_ALE, EBI_BL[1:0], EBI_CS[3:0], EBI_CSTFT, EBI_DCLK, EBI_DTEN, EBI_HSNC, EBI_NANDREn, EBI_NANDWEn, EBI_REn, EBI_VSNC, EBI_WEn I2C0 Full configuration I2C0_SDA, I2C0_SCL I2C1 Full configuration I2C1_SDA, I2C1_SCL USART0 Full configuration with IrDA US0_TX, US0_RX. US0_CLK, US0_CS USART1 Full configuration with I2S US1_TX, US1_RX, US1_CLK, US1_CS USART2 Full configuration with I2S US2_TX, US2_RX, US2_CLK, US2_CS UART0 Full configuration U0_TX, U0_RX UART1 Full configuration U1_TX, U1_RX LEUART0 Full configuration LEU0_TX, LEU0_RX LEUART1 Full configuration LEU1_TX, LEU1_RX TIMER0 Full configuration with DTI TIM0_CC[2:0], TIM0_CDTI[2:0] TIMER1 Full configuration TIM1_CC[2:0] TIMER2 Full configuration TIM2_CC[2:0] TIMER3 Full configuration TIM3_CC[2:0] RTC Full configuration NA BURTC Full configuration NA LETIMER0 Full configuration LET0_O[1:0] PCNT0 Full configuration, 16-bit count register PCNT0_S[1:0] PCNT1 Full configuration, 8-bit count register PCNT1_S[1:0] PCNT2 Full configuration, 8-bit count register PCNT2_S[1:0] ACMP0 Full configuration ACMP0_CH[7:0], ACMP0_O silabs.com | Building a more connected world. Rev. 2.40 | 37 EFM32LG Data Sheet System Summary Module Configuration Pin Connections ACMP1 Full configuration ACMP1_CH[7:0], ACMP1_O VCMP Full configuration NA ADC0 Full configuration ADC0_CH[7:0] DAC0 Full configuration DAC0_OUT[1:0], DAC0_OUTxALT OPAMP Full configuration Outputs: OPAMP_OUTx, OPAMP_OUTxALT, Inputs: OPAMP_Px, OPAMP_Nx AES Full configuration NA GPIO 93 pins Available pins are shown in 5.11.3 GPIO Pinout Overview silabs.com | Building a more connected world. Rev. 2.40 | 38 EFM32LG Data Sheet System Summary 3.2.12 EFM32LG840 The following table describes device-specific implementation of the EFM32LG840 features. Table 3.12. EFM32LG840 Configuration Summary Module Configuration Pin Connections Cortex-M3 Full configuration NA DBG Full configuration DBG_SWCLK, DBG_SWDIO, DBG_SWO MSC Full configuration NA DMA Full configuration NA RMU Full configuration NA EMU Full configuration NA CMU Full configuration CMU_OUT0, CMU_OUT1 WDOG Full configuration NA PRS Full configuration NA I2C0 Full configuration I2C0_SDA, I2C0_SCL I2C1 Full configuration I2C1_SDA, I2C1_SCL USART0 Full configuration with IrDA US0_TX, US0_RX. US0_CLK, US0_CS USART1 Full configuration with I2S US1_TX, US1_RX, US1_CLK, US1_CS USART2 Full configuration with I2S US2_TX, US2_RX, US2_CLK, US2_CS LEUART0 Full configuration LEU0_TX, LEU0_RX LEUART1 Full configuration LEU1_TX, LEU1_RX TIMER0 Full configuration with DTI TIM0_CC[2:0], TIM0_CDTI[2:0] TIMER1 Full configuration TIM1_CC[2:0] TIMER2 Full configuration TIM2_CC[2:0] TIMER3 Full configuration TIM3_CC[2:0] RTC Full configuration NA BURTC Full configuration NA LETIMER0 Full configuration LET0_O[1:0] PCNT0 Full configuration, 16-bit count register PCNT0_S[1:0] PCNT1 Full configuration, 8-bit count register PCNT1_S[1:0] PCNT2 Full configuration, 8-bit count register PCNT2_S[1:0] ACMP0 Full configuration ACMP0_CH[7:4], ACMP0_O ACMP1 Full configuration ACMP1_CH[7:4], ACMP1_O VCMP Full configuration NA ADC0 Full configuration ADC0_CH[7:0] DAC0 Full configuration DAC0_OUT[1:0], DAC0_OUTxALT OPAMP Full configuration Outputs: OPAMP_OUTx, OPAMP_OUTxALT, Inputs: OPAMP_Px, OPAMP_Nx AES Full configuration NA silabs.com | Building a more connected world. Rev. 2.40 | 39 EFM32LG Data Sheet System Summary Module Configuration Pin Connections GPIO 56 pins Available pins are shown in 5.12.3 GPIO Pinout Overview LCD Full configuration LCD_SEG[19:0], LCD_COM[7:0], LCD_BCAP_P, LCD_BCAP_N, LCD_BEXT silabs.com | Building a more connected world. Rev. 2.40 | 40 EFM32LG Data Sheet System Summary 3.2.13 EFM32LG842 The following table describes device-specific implementation of the EFM32LG842 features. Table 3.13. EFM32LG842 Configuration Summary Module Configuration Pin Connections Cortex-M3 Full configuration NA DBG Full configuration DBG_SWCLK, DBG_SWDIO, DBG_SWO MSC Full configuration NA DMA Full configuration NA RMU Full configuration NA EMU Full configuration NA CMU Full configuration CMU_OUT0, CMU_OUT1 WDOG Full configuration NA PRS Full configuration NA I2C0 Full configuration I2C0_SDA, I2C0_SCL I2C1 Full configuration I2C1_SDA, I2C1_SCL USART0 Full configuration with IrDA US0_TX, US0_RX. US0_CLK, US0_CS USART1 Full configuration with I2S US1_TX, US1_RX, US1_CLK, US1_CS USART2 Full configuration with I2S US2_TX, US2_RX, US2_CLK, US2_CS LEUART0 Full configuration LEU0_TX, LEU0_RX LEUART1 Full configuration LEU1_TX, LEU1_RX TIMER0 Full configuration with DTI TIM0_CC[2:0], TIM0_CDTI[2:0] TIMER1 Full configuration TIM1_CC[2:0] TIMER2 Full configuration TIM2_CC[2:0] TIMER3 Full configuration TIM3_CC[2:0] RTC Full configuration NA BURTC Full configuration NA LETIMER0 Full configuration LET0_O[1:0] PCNT0 Full configuration, 16-bit count register PCNT0_S[1:0] PCNT1 Full configuration, 8-bit count register PCNT1_S[1:0] PCNT2 Full configuration, 8-bit count register PCNT2_S[1:0] ACMP0 Full configuration ACMP0_CH[7:4], ACMP0_O ACMP1 Full configuration ACMP1_CH[7:4], ACMP1_O VCMP Full configuration NA ADC0 Full configuration ADC0_CH[7:0] DAC0 Full configuration DAC0_OUT[1:0], DAC0_OUTxALT OPAMP Full configuration Outputs: OPAMP_OUTx, OPAMP_OUTxALT, Inputs: OPAMP_Px, OPAMP_Nx AES Full configuration NA silabs.com | Building a more connected world. Rev. 2.40 | 41 EFM32LG Data Sheet System Summary Module Configuration Pin Connections GPIO 53 pins Available pins are shown in 5.13.3 GPIO Pinout Overview LCD Full configuration LCD_SEG[17:0], LCD_COM[7:0], LCD_BCAP_P, LCD_BCAP_N, LCD_BEXT silabs.com | Building a more connected world. Rev. 2.40 | 42 EFM32LG Data Sheet System Summary 3.2.14 EFM32LG880 The following table describes device-specific implementation of the EFM32LG880 features. Table 3.14. EFM32LG880 Configuration Summary Module Configuration Pin Connections Cortex-M3 Full configuration NA DBG Full configuration DBG_SWCLK, DBG_SWDIO, DBG_SWO MSC Full configuration NA DMA Full configuration NA RMU Full configuration NA EMU Full configuration NA CMU Full configuration CMU_OUT0, CMU_OUT1 WDOG Full configuration NA PRS Full configuration NA EBI Full configuration EBI_A[27:0], EBI_AD[15:0], EBI_ARDY, EBI_ALE, EBI_BL[1:0], EBI_CS[3:0], EBI_CSTFT, EBI_DCLK, EBI_DTEN, EBI_HSNC, EBI_NANDREn, EBI_NANDWEn, EBI_REn, EBI_VSNC, EBI_WEn I2C0 Full configuration I2C0_SDA, I2C0_SCL I2C1 Full configuration I2C1_SDA, I2C1_SCL USART0 Full configuration with IrDA US0_TX, US0_RX. US0_CLK, US0_CS USART1 Full configuration with I2S US1_TX, US1_RX, US1_CLK, US1_CS USART2 Full configuration with I2S US2_TX, US2_RX, US2_CLK, US2_CS UART0 Full configuration U0_TX, U0_RX UART1 Full configuration U1_TX, U1_RX LEUART0 Full configuration LEU0_TX, LEU0_RX LEUART1 Full configuration LEU1_TX, LEU1_RX TIMER0 Full configuration with DTI TIM0_CC[2:0], TIM0_CDTI[2:0] TIMER1 Full configuration TIM1_CC[2:0] TIMER2 Full configuration TIM2_CC[2:0] TIMER3 Full configuration TIM3_CC[2:0] RTC Full configuration NA BURTC Full configuration NA LETIMER0 Full configuration LET0_O[1:0] PCNT0 Full configuration, 16-bit count register PCNT0_S[1:0] PCNT1 Full configuration, 8-bit count register PCNT1_S[1:0] PCNT2 Full configuration, 8-bit count register PCNT2_S[1:0] ACMP0 Full configuration ACMP0_CH[7:0], ACMP0_O ACMP1 Full configuration ACMP1_CH[7:0], ACMP1_O VCMP Full configuration NA silabs.com | Building a more connected world. Rev. 2.40 | 43 EFM32LG Data Sheet System Summary Module Configuration Pin Connections ADC0 Full configuration ADC0_CH[7:0] DAC0 Full configuration DAC0_OUT[1:0], DAC0_OUTxALT OPAMP Full configuration Outputs: OPAMP_OUTx, OPAMP_OUTxALT, Inputs: OPAMP_Px, OPAMP_Nx AES Full configuration NA GPIO 85 pins Available pins are shown in 5.14.3 GPIO Pinout Overview LCD Full configuration LCD_SEG[35:0], LCD_COM[7:0], LCD_BCAP_P, LCD_BCAP_N, LCD_BEXT silabs.com | Building a more connected world. Rev. 2.40 | 44 EFM32LG Data Sheet System Summary 3.2.15 EFM32LG890 The following table describes device-specific implementation of the EFM32LG890 features. Table 3.15. EFM32LG890 Configuration Summary Module Configuration Pin Connections Cortex-M3 Full configuration NA DBG Full configuration DBG_SWCLK, DBG_SWDIO, DBG_SWO MSC Full configuration NA DMA Full configuration NA RMU Full configuration NA EMU Full configuration NA CMU Full configuration CMU_OUT0, CMU_OUT1 WDOG Full configuration NA PRS Full configuration NA EBI Full configuration EBI_A[27:0], EBI_AD[15:0], EBI_ARDY, EBI_ALE, EBI_BL[1:0], EBI_CS[3:0], EBI_CSTFT, EBI_DCLK, EBI_DTEN, EBI_HSNC, EBI_NANDREn, EBI_NANDWEn, EBI_REn, EBI_VSNC, EBI_WEn I2C0 Full configuration I2C0_SDA, I2C0_SCL I2C1 Full configuration I2C1_SDA, I2C1_SCL USART0 Full configuration with IrDA US0_TX, US0_RX. US0_CLK, US0_CS USART1 Full configuration with I2S US1_TX, US1_RX, US1_CLK, US1_CS USART2 Full configuration with I2S US2_TX, US2_RX, US2_CLK, US2_CS UART0 Full configuration U0_TX, U0_RX UART1 Full configuration U1_TX, U1_RX LEUART0 Full configuration LEU0_TX, LEU0_RX LEUART1 Full configuration LEU1_TX, LEU1_RX TIMER0 Full configuration with DTI TIM0_CC[2:0], TIM0_CDTI[2:0] TIMER1 Full configuration TIM1_CC[2:0] TIMER2 Full configuration TIM2_CC[2:0] TIMER3 Full configuration TIM3_CC[2:0] RTC Full configuration NA BURTC Full configuration NA LETIMER0 Full configuration LET0_O[1:0] PCNT0 Full configuration, 16-bit count register PCNT0_S[1:0] PCNT1 Full configuration, 8-bit count register PCNT1_S[1:0] PCNT2 Full configuration, 8-bit count register PCNT2_S[1:0] ACMP0 Full configuration ACMP0_CH[7:0], ACMP0_O ACMP1 Full configuration ACMP1_CH[7:0], ACMP1_O VCMP Full configuration NA silabs.com | Building a more connected world. Rev. 2.40 | 45 EFM32LG Data Sheet System Summary Module Configuration Pin Connections ADC0 Full configuration ADC0_CH[7:0] DAC0 Full configuration DAC0_OUT[1:0], DAC0_OUTxALT OPAMP Full configuration Outputs: OPAMP_OUTx, OPAMP_OUTxALT, Inputs: OPAMP_Px, OPAMP_Nx AES Full configuration NA GPIO 90 pins Available pins are shown in 5.15.3 GPIO Pinout Overview LCD Full configuration LCD_SEG[35:0], LCD_COM[7:0], LCD_BCAP_P, LCD_BCAP_N, LCD_BEXT silabs.com | Building a more connected world. Rev. 2.40 | 46 EFM32LG Data Sheet System Summary 3.2.16 EFM32LG895 The following table describes device-specific implementation of the EFM32LG895 features. Table 3.16. EFM32LG895 Configuration Summary Module Configuration Pin Connections Cortex-M3 Full configuration NA DBG Full configuration DBG_SWCLK, DBG_SWDIO, DBG_SWO MSC Full configuration NA DMA Full configuration NA RMU Full configuration NA EMU Full configuration NA CMU Full configuration CMU_OUT0, CMU_OUT1 WDOG Full configuration NA PRS Full configuration NA EBI Full configuration EBI_A[27:0], EBI_AD[15:0], EBI_ARDY, EBI_ALE, EBI_BL[1:0], EBI_CS[3:0], EBI_CSTFT, EBI_DCLK, EBI_DTEN, EBI_HSNC, EBI_NANDREn, EBI_NANDWEn, EBI_REn, EBI_VSNC, EBI_WEn I2C0 Full configuration I2C0_SDA, I2C0_SCL I2C1 Full configuration I2C1_SDA, I2C1_SCL USART0 Full configuration with IrDA US0_TX, US0_RX. US0_CLK, US0_CS USART1 Full configuration with I2S US1_TX, US1_RX, US1_CLK, US1_CS USART2 Full configuration with I2S US2_TX, US2_RX, US2_CLK, US2_CS UART0 Full configuration U0_TX, U0_RX UART1 Full configuration U1_TX, U1_RX LEUART0 Full configuration LEU0_TX, LEU0_RX LEUART1 Full configuration LEU1_TX, LEU1_RX TIMER0 Full configuration with DTI TIM0_CC[2:0], TIM0_CDTI[2:0] TIMER1 Full configuration TIM1_CC[2:0] TIMER2 Full configuration TIM2_CC[2:0] TIMER3 Full configuration TIM3_CC[2:0] RTC Full configuration NA BURTC Full configuration NA LETIMER0 Full configuration LET0_O[1:0] PCNT0 Full configuration, 16-bit count register PCNT0_S[1:0] PCNT1 Full configuration, 8-bit count register PCNT1_S[1:0] PCNT2 Full configuration, 8-bit count register PCNT2_S[1:0] ACMP0 Full configuration ACMP0_CH[7:0], ACMP0_O ACMP1 Full configuration ACMP1_CH[7:0], ACMP1_O VCMP Full configuration NA silabs.com | Building a more connected world. Rev. 2.40 | 47 EFM32LG Data Sheet System Summary Module Configuration Pin Connections ADC0 Full configuration ADC0_CH[7:0] DAC0 Full configuration DAC0_OUT[1:0], DAC0_OUTxALT OPAMP Full configuration Outputs: OPAMP_OUTx, OPAMP_OUTxALT, Inputs: OPAMP_Px, OPAMP_Nx AES Full configuration NA GPIO 93 pins Available pins are shown in Table 4.3 (p. 70) LCD Full configuration LCD_SEG[35:0], LCD_COM[7:0], LCD_BCAP_P, LCD_BCAP_N, LCD_BEXT silabs.com | Building a more connected world. Rev. 2.40 | 48 EFM32LG Data Sheet System Summary 3.2.17 EFM32LG900 The following table describes device-specific implementation of the EFM32LG900 features. Table 3.17. EFM32LG900 Configuration Summary Module Configuration Pin Connections Cortex-M3 Full configuration NA DBG Full configuration DBG_SWCLK, DBG_SWDIO, DBG_SWO MSC Full configuration NA DMA Full configuration NA RMU Full configuration NA EMU Full configuration NA CMU Full configuration CMU_OUT0, CMU_OUT1 WDOG Full configuration NA PRS Full configuration NA USB Full configuration USB_VBUS, USB_VBUSEN, USB_VREGI, USB_VREGO, USB_DM, USB_DMPU, USB_DP, USB_ID EBI Full configuration EBI_A[27:0], EBI_AD[15:0], EBI_ARDY, EBI_ALE, EBI_BL[1:0], EBI_CS[3:0], EBI_CSTFT, EBI_DCLK, EBI_DTEN, EBI_HSNC, EBI_NANDREn, EBI_NANDWEn, EBI_REn, EBI_VSNC, EBI_WEn I2C0 Full configuration I2C0_SDA, I2C0_SCL I2C1 Full configuration I2C1_SDA, I2C1_SCL USART0 Full configuration with IrDA US0_TX, US0_RX. US0_CLK, US0_CS USART1 Full configuration with I2S US1_TX, US1_RX, US1_CLK, US1_CS USART2 Full configuration with I2S US2_TX, US2_RX, US2_CLK, US2_CS UART0 Full configuration U0_TX, U0_RX UART1 Full configuration U1_TX, U1_RX LEUART0 Full configuration LEU0_TX, LEU0_RX LEUART1 Full configuration LEU1_TX, LEU1_RX TIMER0 Full configuration with DTI TIM0_CC[2:0], TIM0_CDTI[2:0] TIMER1 Full configuration TIM1_CC[2:0] TIMER2 Full configuration TIM2_CC[2:0] TIMER3 Full configuration TIM3_CC[2:0] RTC Full configuration NA BURTC Full configuration NA LETIMER0 Full configuration LET0_O[1:0] PCNT0 Full configuration, 16-bit count register PCNT0_S[1:0] PCNT1 Full configuration, 8-bit count register PCNT1_S[1:0] PCNT2 Full configuration, 8-bit count register PCNT2_S[1:0] ACMP0 Full configuration ACMP0_CH[7:0], ACMP0_O silabs.com | Building a more connected world. Rev. 2.40 | 49 EFM32LG Data Sheet System Summary Module Configuration Pin Connections ACMP1 Full configuration ACMP1_CH[7:0], ACMP1_O VCMP Full configuration NA ADC0 Full configuration ADC0_CH[7:0] DAC0 Full configuration DAC0_OUT[1:0], DAC0_OUTxALT OPAMP Full configuration Outputs: OPAMP_OUTx, OPAMP_OUTxALT, Inputs: OPAMP_Px, OPAMP_Nx AES Full configuration NA GPIO 93 pins Available pins are shown in 5.17.3 GPIO Pinout Overview LCD Full configuration LCD_SEG[35:0], LCD_COM[7:0], LCD_BCAP_P, LCD_BCAP_N, LCD_BEXT silabs.com | Building a more connected world. Rev. 2.40 | 50 EFM32LG Data Sheet System Summary 3.2.18 EFM32LG940 The following table describes device-specific implementation of the EFM32LG940 features. Table 3.18. EFM32LG940 Configuration Summary Module Configuration Pin Connections Cortex-M3 Full configuration NA DBG Full configuration DBG_SWCLK, DBG_SWDIO, DBG_SWO MSC Full configuration NA DMA Full configuration NA RMU Full configuration NA EMU Full configuration NA CMU Full configuration CMU_OUT0, CMU_OUT1 WDOG Full configuration NA PRS Full configuration NA USB Full configuration USB_VBUS, USB_VBUSEN, USB_VREGI, USB_VREGO, USB_DM, USB_DMPU, USB_DP, USB_ID I2C0 Full configuration I2C0_SDA, I2C0_SCL I2C1 Full configuration I2C1_SDA, I2C1_SCL USART0 Full configuration with IrDA US0_TX, US0_RX. US0_CLK, US0_CS USART1 Full configuration with I2S US1_TX, US1_RX, US1_CLK, US1_CS USART2 Full configuration with I2S US2_TX, US2_RX, US2_CLK, US2_CS LEUART0 Full configuration LEU0_TX, LEU0_RX LEUART1 Full configuration LEU1_TX, LEU1_RX TIMER0 Full configuration with DTI TIM0_CC[2:0], TIM0_CDTI[2:0] TIMER1 Full configuration TIM1_CC[2:0] TIMER2 Full configuration TIM2_CC[2:0] TIMER3 Full configuration TIM3_CC[2:0] RTC Full configuration NA BURTC Full configuration NA LETIMER0 Full configuration LET0_O[1:0] PCNT0 Full configuration, 16-bit count register PCNT0_S[1:0] PCNT1 Full configuration, 8-bit count register PCNT1_S[1:0] PCNT2 Full configuration, 8-bit count register PCNT2_S[1:0] ACMP0 Full configuration ACMP0_CH[7:4], ACMP0_O ACMP1 Full configuration ACMP1_O VCMP Full configuration NA ADC0 Full configuration ADC0_CH[7:0] DAC0 Full configuration DAC0_OUT[1:0], DAC0_OUTxALT silabs.com | Building a more connected world. Rev. 2.40 | 51 EFM32LG Data Sheet System Summary Module Configuration Pin Connections OPAMP Full configuration Outputs: OPAMP_OUTx, OPAMP_OUTxALT, Inputs: OPAMP_Px, OPAMP_Nx AES Full configuration NA GPIO 53 pins Available pins are shown in 5.18.3 GPIO Pinout Overview LCD Full configuration LCD_SEG[17:0], LCD_COM[7:0], LCD_BCAP_P, LCD_BCAP_N, LCD_BEXT silabs.com | Building a more connected world. Rev. 2.40 | 52 EFM32LG Data Sheet System Summary 3.2.19 EFM32LG942 The following table describes device-specific implementation of the EFM32LG942 features. Table 3.19. EFM32LG942 Configuration Summary Module Configuration Pin Connections Cortex-M3 Full configuration NA DBG Full configuration DBG_SWCLK, DBG_SWDIO, DBG_SWO MSC Full configuration NA DMA Full configuration NA RMU Full configuration NA EMU Full configuration NA CMU Full configuration CMU_OUT0, CMU_OUT1 WDOG Full configuration NA PRS Full configuration NA USB Full configuration USB_VBUS, USB_VBUSEN, USB_VREGI, USB_VREGO, USB_DM, USB_DMPU, USB_DP, USB_ID I2C0 Full configuration I2C0_SDA, I2C0_SCL I2C1 Full configuration I2C1_SDA, I2C1_SCL USART0 Full configuration with IrDA US0_TX, US0_RX. US0_CLK, US0_CS USART1 Full configuration with I2S US1_TX, US1_RX, US1_CLK, US1_CS USART2 Full configuration with I2S US2_TX, US2_RX, US2_CLK, US2_CS LEUART0 Full configuration LEU0_TX, LEU0_RX LEUART1 Full configuration LEU1_TX, LEU1_RX TIMER0 Full configuration with DTI TIM0_CC[2:0], TIM0_CDTI[2:0] TIMER1 Full configuration TIM1_CC[2:0] TIMER2 Full configuration TIM2_CC[2:0] TIMER3 Full configuration TIM3_CC[2:0] RTC Full configuration NA BURTC Full configuration NA LETIMER0 Full configuration LET0_O[1:0] PCNT0 Full configuration, 16-bit count register PCNT0_S[1:0] PCNT1 Full configuration, 8-bit count register PCNT1_S[1:0] PCNT2 Full configuration, 8-bit count register PCNT2_S[1:0] ACMP0 Full configuration ACMP0_CH[7:4], ACMP0_O ACMP1 Full configuration ACMP1_O VCMP Full configuration NA ADC0 Full configuration ADC0_CH[7:0] DAC0 Full configuration DAC0_OUT[1:0], DAC0_OUTxALT silabs.com | Building a more connected world. Rev. 2.40 | 53 EFM32LG Data Sheet System Summary Module Configuration Pin Connections OPAMP Full configuration Outputs: OPAMP_OUTx, OPAMP_OUTxALT, Inputs: OPAMP_Px, OPAMP_Nx AES Full configuration NA GPIO 50 pins Available pins are shown in 5.19.3 GPIO Pinout Overview LCD Full configuration LCD_SEG[15:0], LCD_COM[7:0], LCD_BCAP_P, LCD_BCAP_N, LCD_BEXT silabs.com | Building a more connected world. Rev. 2.40 | 54 EFM32LG Data Sheet System Summary 3.2.20 EFM32LG980 The following table describes device-specific implementation of the EFM32LG980 features. Table 3.20. EFM32LG980 Configuration Summary Module Configuration Pin Connections Cortex-M3 Full configuration NA DBG Full configuration DBG_SWCLK, DBG_SWDIO, DBG_SWO MSC Full configuration NA DMA Full configuration NA RMU Full configuration NA EMU Full configuration NA CMU Full configuration CMU_OUT0, CMU_OUT1 WDOG Full configuration NA PRS Full configuration NA USB Full configuration USB_VBUS, USB_VBUSEN, USB_VREGI, USB_VREGO, USB_DM, USB_DMPU, USB_DP, USB_ID EBI Full configuration EBI_A[27:0], EBI_AD[15:0], EBI_ARDY, EBI_ALE, EBI_BL[1:0], EBI_CS[3:0], EBI_CSTFT, EBI_DCLK, EBI_DTEN, EBI_HSNC, EBI_NANDREn, EBI_NANDWEn, EBI_REn, EBI_VSNC, EBI_WEn I2C0 Full configuration I2C0_SDA, I2C0_SCL I2C1 Full configuration I2C1_SDA, I2C1_SCL USART0 Full configuration with IrDA US0_TX, US0_RX. US0_CLK, US0_CS USART1 Full configuration with I2S US1_TX, US1_RX, US1_CLK, US1_CS USART2 Full configuration with I2S US2_TX, US2_RX, US2_CLK, US2_CS UART0 Full configuration U0_TX, U0_RX UART1 Full configuration U1_TX, U1_RX LEUART0 Full configuration LEU0_TX, LEU0_RX LEUART1 Full configuration LEU1_TX, LEU1_RX TIMER0 Full configuration with DTI TIM0_CC[2:0], TIM0_CDTI[2:0] TIMER1 Full configuration TIM1_CC[2:0] TIMER2 Full configuration TIM2_CC[2:0] TIMER3 Full configuration TIM3_CC[2:0] RTC Full configuration NA BURTC Full configuration NA LETIMER0 Full configuration LET0_O[1:0] PCNT0 Full configuration, 16-bit count register PCNT0_S[1:0] PCNT1 Full configuration, 8-bit count register PCNT1_S[1:0] PCNT2 Full configuration, 8-bit count register PCNT2_S[1:0] ACMP0 Full configuration ACMP0_CH[7:0], ACMP0_O silabs.com | Building a more connected world. Rev. 2.40 | 55 EFM32LG Data Sheet System Summary Module Configuration Pin Connections ACMP1 Full configuration ACMP1_CH[3:0], ACMP1_O VCMP Full configuration NA ADC0 Full configuration ADC0_CH[7:0] DAC0 Full configuration DAC0_OUT[1:0], DAC0_OUTxALT OPAMP Full configuration Outputs: OPAMP_OUTx, OPAMP_OUTxALT, Inputs: OPAMP_Px, OPAMP_Nx AES Full configuration NA GPIO 81 pins Available pins are shown in 5.20.3 GPIO Pinout Overview LCD Full configuration LCD_SEG[33:0], LCD_COM[7:0], LCD_BCAP_P, LCD_BCAP_N, LCD_BEXT silabs.com | Building a more connected world. Rev. 2.40 | 56 EFM32LG Data Sheet System Summary 3.2.21 EFM32LG990 The following table describes device-specific implementation of the EFM32LG990 features. Table 3.21. EFM32LG990 Configuration Summary Module Configuration Pin Connections Cortex-M3 Full configuration NA DBG Full configuration DBG_SWCLK, DBG_SWDIO, DBG_SWO MSC Full configuration NA DMA Full configuration NA RMU Full configuration NA EMU Full configuration NA CMU Full configuration CMU_OUT0, CMU_OUT1 WDOG Full configuration NA PRS Full configuration NA USB Full configuration USB_VBUS, USB_VBUSEN, USB_VREGI, USB_VREGO, USB_DM, USB_DMPU, USB_DP, USB_ID EBI Full configuration EBI_A[27:0], EBI_AD[15:0], EBI_ARDY, EBI_ALE, EBI_BL[1:0], EBI_CS[3:0], EBI_CSTFT, EBI_DCLK, EBI_DTEN, EBI_HSNC, EBI_NANDREn, EBI_NANDWEn, EBI_REn, EBI_VSNC, EBI_WEn I2C0 Full configuration I2C0_SDA, I2C0_SCL I2C1 Full configuration I2C1_SDA, I2C1_SCL USART0 Full configuration with IrDA US0_TX, US0_RX. US0_CLK, US0_CS USART1 Full configuration with I2S US1_TX, US1_RX, US1_CLK, US1_CS USART2 Full configuration with I2S US2_TX, US2_RX, US2_CLK, US2_CS UART0 Full configuration U0_TX, U0_RX UART1 Full configuration U1_TX, U1_RX LEUART0 Full configuration LEU0_TX, LEU0_RX LEUART1 Full configuration LEU1_TX, LEU1_RX TIMER0 Full configuration with DTI TIM0_CC[2:0], TIM0_CDTI[2:0] TIMER1 Full configuration TIM1_CC[2:0] TIMER2 Full configuration TIM2_CC[2:0] TIMER3 Full configuration TIM3_CC[2:0] RTC Full configuration NA BURTC Full configuration NA LETIMER0 Full configuration LET0_O[1:0] PCNT0 Full configuration, 16-bit count register PCNT0_S[1:0] PCNT1 Full configuration, 8-bit count register PCNT1_S[1:0] PCNT2 Full configuration, 8-bit count register PCNT2_S[1:0] ACMP0 Full configuration ACMP0_CH[7:0], ACMP0_O silabs.com | Building a more connected world. Rev. 2.40 | 57 EFM32LG Data Sheet System Summary Module Configuration Pin Connections ACMP1 Full configuration ACMP1_CH[3:0], ACMP1_O VCMP Full configuration NA ADC0 Full configuration ADC0_CH[7:0] DAC0 Full configuration DAC0_OUT[1:0], DAC0_OUTxALT OPAMP Full configuration Outputs: OPAMP_OUTx, OPAMP_OUTxALT, Inputs: OPAMP_Px, OPAMP_Nx AES Full configuration NA GPIO 86 pins Available pins are shown in 5.21.3 GPIO Pinout Overview LCD Full configuration LCD_SEG[33:0], LCD_COM[7:0], LCD_BCAP_P, LCD_BCAP_N, LCD_BEXT silabs.com | Building a more connected world. Rev. 2.40 | 58 EFM32LG Data Sheet System Summary 3.2.22 EFM32LG995 The following table describes device-specific implementation of the EFM32LG995 features. Table 3.22. EFM32LG995 Configuration Summary Module Configuration Pin Connections Cortex-M3 Full configuration NA DBG Full configuration DBG_SWCLK, DBG_SWDIO, DBG_SWO MSC Full configuration NA DMA Full configuration NA RMU Full configuration NA EMU Full configuration NA CMU Full configuration CMU_OUT0, CMU_OUT1 WDOG Full configuration NA PRS Full configuration NA USB Full configuration USB_VBUS, USB_VBUSEN, USB_VREGI, USB_VREGO, USB_DM, USB_DMPU, USB_DP, USB_ID EBI Full configuration EBI_A[27:0], EBI_AD[15:0], EBI_ARDY, EBI_ALE, EBI_BL[1:0], EBI_CS[3:0], EBI_CSTFT, EBI_DCLK, EBI_DTEN, EBI_HSNC, EBI_NANDREn, EBI_NANDWEn, EBI_REn, EBI_VSNC, EBI_WEn I2C0 Full configuration I2C0_SDA, I2C0_SCL I2C1 Full configuration I2C1_SDA, I2C1_SCL USART0 Full configuration with IrDA US0_TX, US0_RX. US0_CLK, US0_CS USART1 Full configuration with I2S US1_TX, US1_RX, US1_CLK, US1_CS USART2 Full configuration with I2S US2_TX, US2_RX, US2_CLK, US2_CS UART0 Full configuration U0_TX, U0_RX UART1 Full configuration U1_TX, U1_RX LEUART0 Full configuration LEU0_TX, LEU0_RX LEUART1 Full configuration LEU1_TX, LEU1_RX TIMER0 Full configuration with DTI TIM0_CC[2:0], TIM0_CDTI[2:0] TIMER1 Full configuration TIM1_CC[2:0] TIMER2 Full configuration TIM2_CC[2:0] TIMER3 Full configuration TIM3_CC[2:0] RTC Full configuration NA BURTC Full configuration NA LETIMER0 Full configuration LET0_O[1:0] PCNT0 Full configuration, 16-bit count register PCNT0_S[1:0] PCNT1 Full configuration, 8-bit count register PCNT1_S[1:0] PCNT2 Full configuration, 8-bit count register PCNT2_S[1:0] ACMP0 Full configuration ACMP0_CH[7:0], ACMP0_O silabs.com | Building a more connected world. Rev. 2.40 | 59 EFM32LG Data Sheet System Summary Module Configuration Pin Connections ACMP1 Full configuration ACMP1_CH[7:0], ACMP1_O VCMP Full configuration NA ADC0 Full configuration ADC0_CH[7:0] DAC0 Full configuration DAC0_OUT[1:0], DAC0_OUTxALT OPAMP Full configuration Outputs: OPAMP_OUTx, OPAMP_OUTxALT, Inputs: OPAMP_Px, OPAMP_Nx AES Full configuration NA GPIO 93 pins Available pins are shown in 5.22.3 GPIO Pinout Overview LCD Full configuration LCD_SEG[35:0], LCD_COM[7:0], LCD_BCAP_P, LCD_BCAP_N, LCD_BEXT silabs.com | Building a more connected world. Rev. 2.40 | 60 EFM32LG Data Sheet System Summary 3.3 Memory Map The EFM32LG memory map is shown in the following figure, with RAM and flash sizes for the largest memory configuration. Figure 3.2. System Address Space with Core and Code Space Listing silabs.com | Building a more connected world. Rev. 2.40 | 61 EFM32LG Data Sheet System Summary Figure 3.3. System Address Space with Peripheral Listing silabs.com | Building a more connected world. Rev. 2.40 | 62 EFM32LG Data Sheet Electrical Characteristics 4. Electrical Characteristics 4.1 Test Conditions 4.1.1 Typical Values The typical data are based on TAMB=25°C and VDD=3.0 V, as defined in 4.3 General Operating Conditions, unless otherwise specified. 4.1.2 Minimum and Maximum Values The minimum and maximum values represent the worst conditions of ambient temperature, supply voltage and frequencies, as defined in 4.3 General Operating Conditions, unless otherwise specified. 4.2 Absolute Maximum Ratings The absolute maximum ratings are stress ratings, and functional operation under such conditions are not guaranteed. Stress beyond the limits specified in the following table may affect the device reliability or cause permanent damage to the device. Functional operating conditions are given in 4.3 General Operating Conditions. Table 4.1. Absolute Maximum Ratings Parameter Symbol Min Typ Max Unit -40 — 150 °C — — 260 °C VDDMAX 0 — 3.8 V VIOPIN -0.3 — VDD+0.3 V IIOMAX_SINK — — 100 mA IIOMAX_SOURCE — — -100 mA -40 — 105 °C Storage temperature range TSTG Maximum soldering temperature TS External main supply voltage Voltage on any I/O pin Current per I/O pin (sink) Current per I/O pin (source) Test Condition Junction temperature TJ Latest IPC/JEDEC JSTD-020 Standard -G grade devices 4.3 General Operating Conditions Table 4.2. General Operating Conditions Parameter Symbol Min Typ Max Unit TAMB -40 — 85 °C VDDOP 1.98 — 3.8 V Internal APB clock frequency fAPB — — 48 MHz Internal AHB clock frequency fAHB — — 48 MHz Ambient temperature range Operating supply voltage silabs.com | Building a more connected world. Rev. 2.40 | 63 EFM32LG Data Sheet Electrical Characteristics 4.4 Backup Supply Domain Table 4.3. Backup Supply Domain Parameter Symbol Backup supply voltage range VBU_VIN PWRRES resistor Output impedance between BU_VIN and BU_VOUT 1 Supply current RPWRRES RBU_VOUT IBU_VIN Test Condition Min Typ Max Unit 1.8 — 3.8 V EMU_PWRCONF_PWRRES = RES0 4234 4485 4786 Ω EMU_PWRCONF_PWRRES = RES1 2208 2363 2528 Ω EMU_PWRCONF_PWRRES = RES2 1166 1297 1433 Ω EMU_PWRCONF_PWRRES = RES3 295 344 399 Ω EMU_PWRCONF_VOUTSTRONG = 1, EMU_PWRCONF_VOUTMED = 0, EMU_PWRCONF_VOUTWEAK = 0 49 63 80 Ω EMU_PWRCONF_VOUTSTRONG = 0, EMU_PWRCONF_VOUTMED = 1, EMU_PWRCONF_VOUTWEAK = 0 522 670 844 Ω EMU_PWRCONF_VOUTSTRONG = 0, EMU_PWRCONF_VOUTMED = 0, EMU_PWRCONF_VOUTWEAK = 1 5161 6743 7853 Ω BU_VIN not powering backup domain — 3.4 6.5 nA BU_VIN powering backup domain — 197 1050 nA Note: 1. BU_VOUT and BU_STAT signals are not available in all package configurations. Check the device pinout for availability. silabs.com | Building a more connected world. Rev. 2.40 | 64 EFM32LG Data Sheet Electrical Characteristics 4.5 Current Consumption Table 4.4. Current Consumption Parameter EM0 current. No prescaling. Running prime number calculation code from Flash. (Production test condition = 14 MHz) Symbol IEM0 silabs.com | Building a more connected world. Test Condition Min Typ Max Unit 48 MHz HFXO, all peripheral clocks disabled, VDD = 3.0 V, TAMB = 25 °C — 211 225 µA/MHz 48 MHz HFXO, all peripheral clocks disabled, VDD = 3.0 V, TAMB = 85 °C — 211 230 µA/MHz 28 MHz HFRCO, all peripheral clocks disabled, VDD = 3.0 V, TAMB = 25°C — 212 220 µA/MHz 28 MHz HFRCO, all peripheral clocks disabled, VDD = 3.0 V, TAMB = 85°C — 213 223 µA/MHz 21 MHz HFRCO, all peripheral clocks disabled, VDD = 3.0 V, TAMB = 25°C — 214 224 µA/MHz 21 MHz HFRCO, all peripheral clocks disabled, VDD = 3.0 V, TAMB = 85 °C — 215 226 µA/MHz 14 MHz HFRCO, all peripheral clocks disabled, VDD = 3.0 V, TAMB = 25 °C — 216 231 µA/MHz 14 MHz HFRCO, all peripheral clocks disabled, VDD= 3.0 V, TAMB = 85°C — 217 237 µA/MHz 11 MHz HFRCO, all peripheral clocks disabled, VDD = 3.0 V, TAMB = 25 °C — 218 239 µA/MHz 11 MHz HFRCO, all peripheral clocks disabled, VDD = 3.0 V, TAMB = 85 °C — 219 239 µA/MHz 6.6 MHz HFRCO, all peripheral clocks disabled, VDD= 3.0 V, TAMB = 25°C — 224 245 µA/MHz 6.6 MHz HFRCO, all peripheral clocks disabled, VDD = 3.0 V, TAMB = 85°C — 224 258 µA/MHz 1.2 MHz HFRCO, all peripheral clocks disabled, VDD = 3.0 V, TAMB = 25 °C — 257 285 µA/MHz 1.2 MHz HFRCO, all peripheral clocks disabled, VDD = 3.0 V, TAMB = 85 °C — 261 293 µA/MHz Rev. 2.40 | 65 EFM32LG Data Sheet Electrical Characteristics Parameter EM1 current (Production test condition = 14 MHz) EM2 current EM3 current EM4 current Symbol IEM1 IEM2 IEM3 IEM4 Test Condition Min Typ Max Unit 48 MHz HFXO, all peripheral clocks disabled, VDD = 3.0 V, TAMB = 25 °C — 63 75 µA/MHz 48 MHz HFXO, all peripheral clocks disabled, VDD = 3.0 V, TAMB = 85 °C — 65 76 µA/MHz 28 MHz HFRCO, all peripheral clocks disabled, VDD = 3.0 V, TAMB = 25 °C — 64 75 µA/MHz 28 MHz HFRCO, all peripheral clocks disabled, VDD = 3.0 V, TAMB = 85 °C — 65 77 µA/MHz 21 MHz HFRCO, all peripheral clocks disabled, VDD = 3.0 V, TAMB = 25 °C — 65 76 µA/MHz 21 MHz HFRCO, all peripheral clocks disabled, VDD = 3.0 V, TAMB = 85 °C — 66 78 µA/MHz 14 MHz HFRCO, all peripheral clocks disabled, VDD = 3.0 V, TAMB = 25 °C — 67 79 µA/MHz 14 MHz HFRCO, all peripheral clocks disabled, VDD = 3.0 V, TAMB = 85 °C — 68 82 µA/MHz 11 MHz HFRCO, all peripheral clocks disabled, VDD = 3.0 V, TAMB = 25 °C — 68 81 µA/MHz 11 MHz HFRCO, all peripheral clocks disabled, VDD = 3.0 V, TAMB = 85 °C — 70 83 µA/MHz 6.6 MHz HFRCO, all peripheral clocks disabled, VDD = 3.0 V, TAMB = 25 °C — 74 87 µA/MHz 6.6 MHz HFRCO, all peripheral clocks disabled, VDD = 3.0 V, TAMB = 85 °C — 76 89 µA/MHz 1.2 MHz HFRCO. all peripheral clocks disabled, VDD = 3.0 V, TAMB = 25 °C — 106 120 µA/MHz 1.2 MHz HFRCO. all peripheral clocks disabled, VDD = 3.0 V, TAMB = 85 °C — 112 129 µA/MHz EM2 current with RTC prescaled to 1 Hz, 32.768 kHz LFRCO, VDD = 3.0 V, TAMB = 25 °C — 0.951 1.71 µA EM2 current with RTC prescaled to 1 Hz, 32.768 kHz LFRCO, VDD = 3.0 V, TAMB = 85 °C — 3.01 4.01 µA VDD = 3.0 V, TAMB = 25 °C — 0.65 1.3 µA VDD = 3.0 V, TAMB = 85 °C — 2.65 4.0 µA VDD = 3.0 V, TAMB = 25 °C — 0.020 0.055 µA VDD = 3.0 V, TAMB = 85 °C — 0.44 0.90 µA Note: 1. Using backup RTC. silabs.com | Building a more connected world. Rev. 2.40 | 66 EFM32LG Data Sheet Electrical Characteristics 4.5.1 EM1 Current Consumption 3.10 3.10 3.05 3.05 Idd [mA] 3.15 Idd [mA] 3.15 3.00 3.00 -40°C -15°C 5°C 25°C 45°C 65°C 85°C 2.95 2.90 2.0 2.0V 2.2V 2.4V 2.6V 2.8V 3.0V 3.2V 3.4V 3.6V 3.8V 2.2 2.4 2.6 2.8 3.0 Vdd [V] 3.2 3.4 3.6 2.95 2.90 –40 3.8 –15 5 25 Temperature [°C] 45 65 85 Figure 4.1. EM1 Current Consumption with all Peripheral Clocks Disabled and HFXO Running at 48 MHz 1.80 1.80 1.75 1.75 Idd [mA] 1.85 Idd [mA] 1.85 1.70 1.70 -40°C -15°C 5°C 25°C 45°C 65°C 85°C 1.65 1.60 2.0 2.0V 2.2V 2.4V 2.6V 2.8V 3.0V 3.2V 3.4V 3.6V 3.8V 2.2 2.4 2.6 2.8 3.0 Vdd [V] 3.2 3.4 3.6 1.65 3.8 1.60 –40 –15 5 25 Temperature [°C] 45 65 85 Figure 4.2. EM1 Current Consumption with all Peripheral Clocks Disabled and HFRCO Running at 28 MHz silabs.com | Building a more connected world. Rev. 2.40 | 67 EFM32LG Data Sheet 1.42 1.42 1.40 1.40 1.38 1.38 1.36 1.36 1.34 1.34 Idd [mA] Idd [mA] Electrical Characteristics 1.32 -40°C -15°C 5°C 25°C 45°C 65°C 85°C 1.30 1.28 1.26 1.24 2.0 2.2 2.4 2.6 2.8 3.0 Vdd [V] 3.2 3.4 3.6 2.0V 2.2V 2.4V 2.6V 2.8V 3.0V 3.2V 3.4V 3.6V 3.8V 1.32 1.30 1.28 1.26 1.24 –40 3.8 –15 5 25 Temperature [°C] 45 65 85 0.98 0.98 0.96 0.96 0.94 0.94 Idd [mA] Idd [mA] Figure 4.3. EM1 Current Consumption with all Peripheral Clocks Disabled and HFRCO Running at 21 MHz 0.92 -40°C -15°C 5°C 25°C 45°C 65°C 85°C 0.90 0.88 0.86 2.0 2.2 2.4 2.6 2.8 3.0 Vdd [V] 3.2 3.4 3.6 2.0V 2.2V 2.4V 2.6V 2.8V 3.0V 3.2V 3.4V 3.6V 3.8V 0.92 0.90 0.88 3.8 0.86 –40 –15 5 25 Temperature [°C] 45 65 85 Figure 4.4. EM1 Current Consumption with all Peripheral Clocks Disabled and HFRCO Running at 14 MHz silabs.com | Building a more connected world. Rev. 2.40 | 68 EFM32LG Data Sheet 0.78 0.78 0.76 0.76 Idd [mA] Idd [mA] Electrical Characteristics 0.74 -40°C -15°C 5°C 25°C 45°C 65°C 85°C 0.72 0.70 2.0 2.2 2.4 2.6 2.8 3.0 Vdd [V] 3.2 3.4 3.6 2.0V 2.2V 2.4V 2.6V 2.8V 3.0V 3.2V 3.4V 3.6V 3.8V 0.74 0.72 0.70 3.8 –40 –15 5 25 Temperature [°C] 45 65 85 0.52 0.52 0.51 0.51 0.50 0.50 0.49 0.49 Idd [mA] Idd [mA] Figure 4.5. EM1 Current Consumption with all Peripheral Clocks Disabled and HFRCO Running at 11 MHz 0.48 -40°C -15°C 5°C 25°C 45°C 65°C 85°C 0.47 0.46 0.45 2.0 2.2 2.4 2.6 2.8 3.0 Vdd [V] 3.2 3.4 3.6 2.0V 2.2V 2.4V 2.6V 2.8V 3.0V 3.2V 3.4V 3.6V 3.8V 0.48 0.47 0.46 3.8 0.45 –40 –15 5 25 Temperature [°C] 45 65 85 Figure 4.6. EM1 Current Consumption with all Peripheral Clocks Disabled and HFRCO Running at 6.6 MHz silabs.com | Building a more connected world. Rev. 2.40 | 69 EFM32LG Data Sheet Electrical Characteristics 0.160 0.138 -40°C -15°C 5°C 25°C 45°C 65°C 85°C 0.136 0.134 0.150 0.145 Idd [mA] Idd [mA] 0.132 0.155 0.130 0.140 2.0V 2.2V 2.4V 2.6V 2.8V 3.0V 3.2V 3.4V 3.6V 3.8V 0.135 0.128 0.130 0.126 0.125 0.124 0.122 2.0 0.120 2.2 2.4 2.6 2.8 3.0 Vdd [V] 3.2 3.4 3.6 3.8 0.115 –40 –15 5 25 Temperature [°C] 45 65 85 Figure 4.7. EM1 Current Consumption with all Peripheral Clocks Disabled and HFRCO Running at 1.2 MHz 4.5.2 EM2 Current Consumption 3.5 3.5 -40.0°C -15.0°C 5.0°C 25.0°C 45.0°C 65.0°C 85.0°C 3.0 2.5 Idd [uA] Idd [uA] 2.5 3.0 2.0 2.0 1.5 1.5 1.0 1.0 0.5 2.0 2.2 2.4 2.6 2.8 3.0 Vdd [V] 3.2 3.4 3.6 3.8 0.5 –40 Vdd=2.0V Vdd=2.2V Vdd=2.4V Vdd=2.6V Vdd=2.8V Vdd=3.0V Vdd=3.2V Vdd=3.4V Vdd=3.6V Vdd=3.8V –20 0 20 40 Temperature [°C] 60 80 Figure 4.8. EM2 Current Consumption, RTC1 prescaled to 1 kHz, 32.768 kHz LFRCO Note: 1. Using backup RTC. silabs.com | Building a more connected world. Rev. 2.40 | 70 EFM32LG Data Sheet Electrical Characteristics 4.5.3 EM3 Current Consumption 3.0 3.0 -40.0°C -15.0°C 5.0°C 25.0°C 45.0°C 65.0°C 85.0°C 2.5 2.0 Idd [uA] Idd [uA] 2.0 2.5 1.5 1.5 1.0 1.0 0.5 0.5 0.0 2.0 2.2 2.4 2.6 2.8 3.0 Vdd [V] 3.2 3.4 3.6 0.0 –40 3.8 Vdd=2.0V Vdd=2.2V Vdd=2.4V Vdd=2.6V Vdd=2.8V Vdd=3.0V Vdd=3.2V Vdd=3.4V Vdd=3.6V Vdd=3.8V –20 0 20 40 Temperature [°C] 60 80 0 20 40 Temperature [°C] 60 80 Figure 4.9. EM3 Current Consumption 4.5.4 EM4 Current Consumption 0.7 0.6 0.6 0.5 0.4 Idd [uA] Idd [uA] 0.5 0.7 -40.0°C -15.0°C 5.0°C 25.0°C 45.0°C 65.0°C 85.0°C 0.3 0.4 0.3 0.2 0.2 0.1 0.1 0.0 2.0 2.2 2.4 2.6 2.8 3.0 Vdd [V] 3.2 3.4 3.6 3.8 Vdd=2.0V Vdd=2.2V Vdd=2.4V Vdd=2.6V Vdd=2.8V Vdd=3.0V Vdd=3.2V Vdd=3.4V Vdd=3.6V Vdd=3.8V 0.0 –40 –20 Figure 4.10. EM4 Current Consumption silabs.com | Building a more connected world. Rev. 2.40 | 71 EFM32LG Data Sheet Electrical Characteristics 4.6 Transition between Energy Modes The transition times are measured from the trigger to the first clock edge in the CPU. Table 4.5. Energy Modes Transitions Parameter Symbol Min Typ Max Unit Transition time from EM1 to EM0 tEM10 — 0 — HFCORECLK cycles Transition time from EM2 to EM0 tEM20 — 2 — µs Transition time from EM3 to EM0 tEM30 — 2 — µs Transition time from EM4 to EM0 tEM40 — 163 — µs 4.7 Power Management The EFM32LG requires the AVDD_x, VDD_DREG and IOVDD_x pins to be connected together (with optional filter) at the PCB level. For practical schematic recommendations, see the application note, AN0002.0: EFM32 and EZR32 Wireless MCU Series 0 Hardware Design Considerations. Table 4.6. Power Management Parameter Symbol Test Condition Min Typ Max Unit BOD threshold on falling external supply voltage VBODextthr- 1.74 — 1.96 V BOD threshold on rising external supply voltage VBODextthr+ — 1.85 1.98 V Power-on Reset (POR) threshold on rising external supply voltage VPORthr+ — — 1.98 V Delay from reset is released until program execution starts tRESET Applies to Power-on Reset, Brownout Reset and pin reset. — 163 — µs Voltage regulator decoupling capacitor. CDECOUPLE X5R capacitor recommended. Apply between DECOUPLE pin and GROUND — 1 — µF USB voltage regulator out decoupling capacitor. CUSB_VREGO X5R capacitor recommended. Apply between USB_VREGO pin and GROUND — 1 — µF USB voltage regulator in decoupling capacitor. CUSB_VREGI X5R capacitor recommended. Apply between USB_VREGI pin and GROUND — 4.7 — µF silabs.com | Building a more connected world. Rev. 2.40 | 72 EFM32LG Data Sheet Electrical Characteristics 4.8 Flash Table 4.7. Flash Parameter Symbol Flash erase cycles before failure Flash word write cycles between erase Flash data retention Min Typ Max Unit ECFLASH 20000 — — cycles WWCFLASH — — 21 cycles TAMB