SI2494-A-FMR

Si2494/39 V. 92 A N D V.34 ISO MODEM ® W I T H G LOBAL DAA Features             EEPROM interface Commercial or industrial temperature range DTMF detection/generation Si3000 Voice Codec Interface Hardware support for mic, speaker, and/or handset Programmable voice filters, limiters, and sidetone Supports TBR-38, TIA/EIA4790 and other voice standards Voice pass through with compression Supports telephone answering machine, music on hold, voice menus, etc Full-duplex speakerphone support Line echo cancellation Acoustic echo cancellation GPIO16, D2 GPIO17, D1 GPIO25, D3 30 GPIO24, D4 CLKOUT 3 29 ESC, D5 N/C 4 28 DCD, D6 VDD 5 GND 6 VREG 7 SDI 8 SDO Si2494/39 27 N/C 26 VDD 25 GND 24 RTS, SS, D7 9 23 TXD, MOSI, WR EESDI 10 22 RXD, MISO, RD EESDO 11 21 CTS, SCLK, CS EECS 12 20 GPIO11, A0 5 x 7 mm QFN 13 14 15 16 17 18 19 RI C1A C2A RESET Rev. 1.0 7/11 Telco Tip Ring INT  UART  SPI  Parallel Global DAA BOM 31 2 AOUTb Host Interface Si3018 Line Side 1 AOUT System Block Diagram 38 37 36 35 34 33 32 GPIO1 FSYNC EECLK The Si2494/39 ISOmodem is a full-featured ITU V.92/V.34-compliant modem that provides connect rates of up to 56 kbps, full-duplex, over the public switched telephone network (PSTN). Offered as a chipset with the Si2494/39 system-side device and the Si3018 line-side device, the ISOModem utilizes Silicon Laboratories’ patented direct access arrangment (DAA) technology to provide a programmable telephone line interface with an unparalleled level of integration. This compact solution eliminates the need for a separate DSP, modem controller, codec, transformer, relay, opto-isolators, clocking crystal, and 2-4 wire hybrid. The addition of the Si3000 voice codec supports a voice handset and/or full-duplex speakerphone. Voice pass-through with optional compression supports tapeless answering machine, music-on-hold, voice menus, etc. The Si2494/39 is ideal for embedded modem applications due to its flexibility, small footprint, and minimal external component count. GPIO18, D0 Medical Remote monitoring Description Si2494 System Side Pin Assignments CLKIN/XTALI   Point-of-sale terminals Security Host CPU This data sheet is valid only for those chipset combinations listed on page 59. N/C Applications   Ordering Information XTALO    Data modem formats ITU-T, Bell 300 bps up to 56 kbps V.21,V.22, V.29 Fast Connect V.44, V.42, V.42bis, MNP2-5 Automatic rate negotiation V.92 PCM upstream V.92 Quick connect V.92 Modem on hold Type I and II caller ID decode No external ROM or RAM required UART, SPI, or parallel interface Flexible clock options Low-cost 32.768 kHz oscillator 4.915 MHz oscillator 27 MHz clock input Integrated DAA Over 6000 V capacitive isolation Parallel phone detect Globally-compliant line interface Overcurrent detection AT command set support SMS / MMS support Firmware upgradeable Si3018 QE 1 DCT 2 RX 3 IB 4 C1B 5 C2B 6 VREG 7 RNG1 8 16 DCT2 15 IGND 14 DCT3 13 12 11 10 9 QB QE2 SC VREG2 RNG2 Capacitive Isolation Barrier Copyright © 2011 by Silicon Laboratories Si2494/39 Si2494/39 2 Rev. 1.0 Si2494/39 TABLE O F C ONTENTS Section Page 1. Electrical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 2. Typical Application Schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 3. Bill of Materials: Si2494/39 Chipset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 4. Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 4.1. Host Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 4.2. Command Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20 4.3. Data Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 4.4. Fast Connect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20 4.5. V.80 Synchronous Access Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 4.6. Voice Mode (+FCLASS=8) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 4.7. Clocking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 4.8. Low-Power Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 4.9. Data Compression . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 4.10. Error Correction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 4.11. Wire Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21 4.12. V.92 PCM Upstream . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 4.13. V.92 Quick Connect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 4.14. V.92 Modem-on-Hold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 4.15. Caller ID Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23 4.16. Parallel Phone Detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 4.17. Overcurrent Detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 4.18. Global Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 4.19. Firmware Upgrades . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24 4.20. DTMF Detection / Generation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 4.21. SMS/MMS Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25 4.22. Codec Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 4.23. Answering Machine Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25 4.24. Voice Pass-Through (Speakerphone) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25 4.25. General-Purpose Tone Detectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 4.26. EEPROM Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 4.27. AT Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26 4.28. Extended AT Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 5. S-Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 6. User-Access Registers (U-Registers) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 7. Pin Descriptions: Si2494/39 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 8. Pin Descriptions: Si3018 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58 9. Ordering Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59 10. Package Markings (Top Markings) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 10.1. Si2494 Top Marking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 10.2. Si2439 Top Marking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 10.3. Si2494/39 Top Markings Explanation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61 10.4. Si3018 Top Marking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62 10.5. Si3018 Top Markings Explanation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62 Rev. 1.0 3 Si2494/39 11. Package Outline: 38-Pin QFN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63 12. 38-Pin QFN Land Pattern . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65 13. Package Outline: 16-Pin SOIC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66 14. 16-Pin SOIC Land Pattern . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68 Contact Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70 4 Rev. 1.0 Si2494/39 1. Electrical Specifications Table 1. Recommended Operating Conditions Symbol Test Condition Min2 Typ Max2 Unit Ambient Temperature TA F-grade G-grade 0 –40 25 25 70 85 °C Si2494/39 Supply Voltage, Digital3 VD 3.0 3.3 3.6 V Parameter1 Notes: 1. The Si2494/39 specifications are guaranteed when the typical application circuit (including component tolerance) and any Si2494/39 and any Si3018 are used. See "2. Typical Application Schematic" on page 12. 2. All minimum and maximum specifications are guaranteed and apply across the recommended operating conditions. Typical values apply at nominal supply voltages and an operating temperature of 25 °C unless otherwise stated. 3. The digital supply, VD, operates from 3.0 to 3.6 V. Figure 1. Test Circuit for Loop Characteristics Table 2. DC Characteristics, VD = 3.0 to 3.6 V (VD = 3.0 to 3.6 V, TA = 0 to 70 °C for F-grade, TA = –40 to 85 °C for G-grade) Parameter Symbol Test Condition Min Typ Max Unit High Level Input Voltage VIH 2.0 — — V Low Level Input Voltage VIL — — 0.8 V High Level Output Voltage VOH IO = –2 mA 2.4 — — V Low Level Output Voltage VOL IO = 2 mA — — 0.35 V Input Leakage Current IL –10 — 10 µA Pullup Resistance Pins RPU 50 125 200 k Total Supply Current* ID — 17 35 mA Total Supply Current, Wake-On-Ring* ID — 4.4 — mA Total Supply Current, Powerdown* ID — 80 — µA PDN = 1 *Note: All inputs at 0 or VD. All inputs held static except clock and all outputs unloaded (Static IOUT = 0 mA). Rev. 1.0 5 Si2494/39 Table 3. AC Characteristics (VD = 3.0 to 3.6 V, TA = 0 to 70 °C for F-grade, Fs = 8 kHz, TA = –40 to 85 °C for G-grade) Parameter Symbol Sample Rate Test Condition Fs Clock Input Frequency FXTL default Min Typ Max Unit — 8 — kHz — 4.9152 — MHz Mode1 — 27 — MHz Clock Input Frequency FXTL 27 MHz Clock Input Frequency FXTL 32 kHz Mode1 — 32.768 — kHz Receive Frequency Response Low –3 dBFS Corner, FILT = 0 — 5 — Hz Receive Frequency Response Low –3 dBFS Corner, FILT = 1 — 200 — Hz VFS — 1.1 — VPEAK Receive Full Scale Level2,3 VFS — 1.1 — VPEAK Dynamic Range4 DR ILIM = 0, DCV = 11, MINI = 00 DCR = 0, IL = 100 mA — 80 — dB Dynamic Range4 DR ILIM = 0, DCV = 00, MINI = 11 DCR = 0, IL = 20 mA — 80 — dB Dynamic Range4 DR ILIM = 1, DCV = 11, MINI = 00 DCR = 0, IL = 50 mA — 80 — dB Transmit Total Harmonic Distortion5 THD ILIM = 0, DCV = 11, MINI = 00 DCR = 0, IL = 100 mA — –72 — dB Transmit Total Harmonic Distortion5 THD ILIM = 0, DCV = 00, MINI = 11 DCR = 0, IL = 20 mA — –78 — dB Receive Total Harmonic Distortion5 THD ILIM = 0, DCV = 00, MINI = 11 DCR = 0, IL = 20 mA — –78 — dB Receive Total Harmonic Distortion5 THD ILIM = 1,DCV = 11, MINI=00 DCR = 0, IL = 50 mA — –78 — dB DRCID VIN = 1 kHz, –13 dBm — 50 — dB Transmit Full Scale Level2 Dynamic Range (Caller ID Mode) Notes: 1. Refer to “AN93: ISOmodem® Chipset Family Designer's Guide” for configuring clock input reset strapping. 2. Measured at TIP and RING with 600 termination at 1 kHz, as shown in Figure 1 on page 5. 3. Receive full scale level produces –0.9 dBFS at DTX. 4. DR = 20 x log |Vin| + 20 x log (rms signal/rms noise). Applies to both transmit and receive paths. Vin = 1 kHz, –3 dBFS. 5. Vin = 1 kHz, –3 dBFS. THD = 20 x log (rms distortion/rms signal). 6 Rev. 1.0 Si2494/39 Table 4. Loop Characteristics (VD = 3.0 to 3.6 V, TA = 0 to 70 °C for F-grade, TA = –40 to 85 °C for G-grade) Parameter Symbol DC Termination Voltage VTR DC Termination Voltage VTR DC Termination Voltage VTR DC Termination Voltage VTR DC Termination Voltage VTR DC Termination Voltage VTR DC Termination Voltage VTR On-Hook Leakage Current Operating Loop Current Operating Loop Current DC Ring Current ILK ILP ILP Ring Detect Voltage2 Ring Detect Voltage2 Ring Frequency Ringer Equivalence Number Test Condition 1 IL = 20 mA, ILIM = 0 DCV = 00, MINI = 11, DCR = 0 IL = 120 mA, ILIM = 0 DCV = 00, MINI = 11, DCR = 0 IL = 20 mA, ILIM = 0 DCV = 11, MINI = 00, DCR = 0 IL = 120 mA, ILIM = 0 DCV = 11, MINI = 00, DCR = 0 IL = 20 mA, ILIM = 1 DCV = 11, MINI = 00, DCR = 0 IL = 60 mA, ILIM = 1 DCV = 11, MINI = 00, DCR = 0 IL = 50 mA, ILIM = 1 DCV = 11, MINI = 00, DCR = 0 VTR = –48 V MINI = 00, ILIM = 0 MINI = 00, ILIM = 1 DC current flowing through ring detection circuitry RT = 0 RT = 1 VRD VRD FR REN Min Typ Max Unit — — 6.0 V 9 — — V — — 7.5 V 9 — — V — — 7.5 V 40 — — V — — 40 V — 10 10 — — — — 1.5 5 120 60 3 µA mA mA µA 12 18 15 — 15 21 — — 18 25 68 0.2 VRMS VRMS Hz Notes: 1. ILIM = U67, bit 9; DCV = U67, bits 3:2; MINI = U67, bits 13:12; DCR = U67, bit 7; RT = U67, bit 0. 2. The ring signal is guaranteed to not be detected below the minimum. The ring signal is guaranteed to be detected above the maximum. TIP + 600  Si3018 IL VTR 10 µF – RING Rev. 1.0 7 Si2494/39 Table 5. Switching Characteristics1 (VD = 3.0 to 3.6 V, TA = 0 to 70 °C for F-grade, TA = –40 to 85 °C for G-grade) Parameter Symbol Min Typ Max Unit 2.048 — 49.152 MHz tBD –1 — 1 % RESET to RESET tRS 5.02 — — ms RESET to 1st AT Command tAT 300 — — ms Address Setup tAS 15 — — ns Address Hold tAH 0 — — ns WR Low Pulse Width tWL 50 — — ns tWDSU 20 — — ns Write Cycle Time tWC 120 — — ns Chip Select Setup tCSS 10 — — ns Chip Select Hold tCSH 0 — — ns tRL 50 — — ns tRLDD — — 20 ns Data Hold tDH 10 — — ns RD High to Hi-Z Time tDZ — — 30 ns Read Cycle Time tRC 120 — — ns tWRC 120 — — ns UART Timing Parameters CLKOUT Output Clock Frequency Baud Rate Accuracy Reset Timing Parameters Parallel Timing Parameters Write Data Setup Time RD Low Pulse Width RD Low to Data Driven Time Write to Read Cycle Time Serial Peripheral Interface (SPI) Timing Parameters SS Falling to First SCLK Edge tSE 41 — — ns Last SCLK Edge to SS Rising tSD 41 — — ns SS Rising to MISO High-Z tSDZ — — 93 ns SCLK High Time tCKH 102 — — ns SCLK Low Time tCKL 102 — — ns MOSI Valid to SCLK Sample Edge tSIS 41 — — ns SCLK Sample Edge to MOSI Change tSIH 41 — — ns SCLK Shift Edge to MISO Change tSOH — — 93 ns Notes: 1. All timing is referenced to the 50% level of the waveform. Input test levels are VIH = VD – 0.4 V, VIL = 0.4 V. 2. With 32.768 kHz clocking, allow 500 to the reset low-to-high minimum pulse on power-up and wake-from-power-down conditions. 8 Rev. 1.0 Si2494/39 Table 5. Switching Characteristics1 (Continued) (VD = 3.0 to 3.6 V, TA = 0 to 70 °C for F-grade, TA = –40 to 85 °C for G-grade) Parameter Symbol Min Typ Max Unit tSCK 224 — — ns tNSS_INACT 81 — — ns SCLK cycle time Inactive time between SS actives Notes: 1. All timing is referenced to the 50% level of the waveform. Input test levels are VIH = VD – 0.4 V, VIL = 0.4 V. 2. With 32.768 kHz clocking, allow 500 to the reset low-to-high minimum pulse on power-up and wake-from-power-down conditions. Table 6. Thermal Conditions Parameter Symbol Test Condition Min Typ Max Unit Thermal Resistance (Si2494/39) JA QFN-38 — 35 — °C/W Thermal Resistance (Si3018) JA SOIC-16 — 77 — °C/W Maximum Junction Temperature (Si2494/39) T QFN-38 — — 105 °C Maximum Junction Temperature (Si3018) T SOIC-16 — — 110 °C Table 7. Absolute Maximum Ratings Parameter Symbol Value Unit DC Supply Voltage VD 4.1 V Input Current, Si2494/39 Digital Input Pins IIN ±10 mA Digital Input Voltage VIND –0.3 to (VD + 0.3) V CLKIN/XTALI Input Voltage VXIND –0.3 to (VD + 0.3) V TA –10 to 100 °C TSTG –40 to 150 °C Operating Temperature Range Storage Temperature Range Note: Permanent device damage may occur if the above absolute maximum ratings are exceeded. Functional operation should be restricted to the conditions as specified in the operational sections of this data sheet. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Rev. 1.0 9 Si2494/39 SS T T SE T CKL SD SCLK* T CKH T T SIS SIH MOSI T SEZ T T SOH SDZ MISO Figure 2. SPI Slave Timing 10 Rev. 1.0 Si2494/39 t CSS t CSH t AS t AH CS A0 ADDRESS = 0 or 1 tW L tW C WR t W DSU t DH D[7:0] VALID DATA VALID DATA Figure 3. Parallel Interface Write Timing CS A0 ADDRESS = 0 or 1 WR tWRC RD tWDSU tDH D[7:0] VALID DATA VALID DATA tRLDD Figure 4. Parallel Interface Write Followed by Read Timing Rev. 1.0 11 ESC DCDb RTSb TXD RXD CTSb RIb 16 20 34 33 32 31 30 29 28 24 23 22 21 19 INTb RESETb 35 15 14 10 11 12 13 EESDI EESDO EECS EECLK AOUT AOUTb 2 3 8 9 FSYNCH CLKOUT SDI SDO 4 27 38 1 U1 Si2493 C2A C1A VREG RESET_ AOUT AOUTb GPIO11/A0 GPIO18/D0 GPIO17/D1 GPIO16/D2 CLKIN/XTALI GPIO25/D3 GPIO24/D4 EC/D5 DCD_/D6 XTALO UART_RTS_/SPI_CS_/D7 UART_TXD/SPI_MOSI/WR_ UART_RXD/SPI_MISO/RD_ UART_CTS_/SPI_SCLK/CS_ RIb INT_ EESDI EESDO EECS EECLK FSYNCH_ CLKOUT SDI SDO NC1 NC2 NC3 GPIO1 26 VDD 5 VDD GND 6 GND 25 37 36 17 18 7 Y1 C50 C41 C40 C51 C52 56.2 R13 56.2 R12 R9 Bias C2 C1 C5 7 4 6 5 10 Rev. 1.0 QB DCT2 DCT3 DCT RX VREG2 RNG1 RNG2 QE QE2 Si3018 VREG IB C2B C1B Q5 R7 R8 R1 R2 C4 Q4 R4 R5 Q1 I_GND R3 Ring Detect/CID/Voltage monitoring R11 DC Term. R10 No Ground Plane In DAA Section 8 9 1 12 13 16 14 2 3 C7 Z1 Q2 Hookswitch Figure 5. Typical Si2494/39 Schematic I_GND C6 33pF 33pF U2 Add 0.020 to 0.030 sq. inches of Cu at all transistor collectors IGND 15 SC 12 + 11 VDD Q3 C10 R6 C3 + I_GND Place C3 near D1 Hookswitch - I_GND D1 HD04 FB1 FB2 C9 C8 R15 R16 Emissios Option RV1 RING TIP Si2494/39 2. Typical Application Schematic Si2494/39 3. Bill of Materials: Si2494/39 Chipset Component Value Supplier(s) C1, C2 33 pF, Y2, X7R, ±20% Panasonic, Murata, Vishay C3 10 nF, 250 V, X7R, ±20% Venkel, SMEC C4 1.0 µF, 50 V, Elec/Tant, ±20% Panasonic C5, C6, C50, C52 0.1 µF, 16 V, X7R, ±20% Venkel, SMEC C7 2.7 nF, 50 V, X7R, ±20% Venkel, SMEC C8, C9 680 pF, Y2, X7R, ±10% Panasonic, Murata, Vishay C10 0.01 µF, 16 V, X7R, ±20% Venkel, SMEC C40 C41 4.9152 MHz: 33 pF, 16 V, NPO, ±5% 32.768 kHz: 18 pF, 16 V, NPO, ±5% 27 MHz: Not Populated C51 D1, D2 Venkel, SMEC 1 0.22 µF, 16 V, X7R, ±20% Venkel, SMEC Dual Diode, 225 mA, 300 V, CMPD2004S Central Semiconductor FB1, FB2 Ferrite Bead, BLM21AG601SN1 Murata Q1, Q3 NPN, 300 V, MMBTA42 OnSemi, Fairchild Q2 PNP, 300 V, MMBTA92 OnSemi, Fairchild Q4, Q5 NPN, 80 V, 330 mW, MMBTA06 OnSemi, Fairchild RV1 Sidactor, 275 V, 100 A Teccor, Protek, ST Micro R1 1.07 k, 1/2 W, 1% Venkel, SMEC, Panasonic R2 150 , 1/16 W, 5% Venkel, SMEC, Panasonic R3 3.65 k, 1/2 W, 1% Venkel, SMEC, Panasonic R4 2.49 k, 1/2 W, 1% Venkel, SMEC, Panasonic R5, R6 100 k, 1/16 W, 5% Venkel, SMEC, Panasonic R7, R8 20 M, 1/16 W, 5% Venkel, SMEC, Panasonic R9 1 M, 1/16 W, 1% Venkel, SMEC, Panasonic R10 536 , 1/4 W, 1% Venkel, SMEC, Panasonic R11 73.2 , 1/2 W, 1% Venkel, SMEC, Panasonic 56 , 1/16 W, 1% Venkel, SMEC, Panasonic R15, R16 0 , 1/16 W Venkel, SMEC, Panasonic U1 Si2494/39 Silicon Labs U2 Si3018 Silicon Labs R12, R13 2 32.768 kHz, 12 pF, 100 ppm, 35 k max ESR 3 Y1 4.9152 MHz, 20 pF, 100 ppm, 150  ESR ECS Inc., Siward 27 MHz (from external clock) Z1 Zener Diode, 43 V, 1/2 W, BZT84C43 On Semi Notes: 1. Several diode bridge configurations are acceptable. For example, a single DF04S or four 1N4004 diodes may be used. 2. Murata BLM21AG601SN1 may be substituted for R15–R16 (0 ) to decrease emissions. 3. To ensure compliance with ITU specifications, frequency tolerance must be less than 100 ppm including initial accuracy, 5-year aging, 0 to 70 °C, and capacitive loading. For optimal V.92 PCM upstream performance, the recommended crystal accuracy is ±25 ppm. Rev. 1.0 13 Si2494/39 Table 8. Protocol Characteristics 14 Item Specification Data Rate (downstream) 56 kbps 54.666 kbps 53.333 kbps 52 kbps 50.666 kbps 49.333 kbps 48 kbps 46.666 kbps 45.333 kbps 44 kbps 42.666 kbps 41.333 kbps 40 kbps 38.666 kbps 37.333 kbps 36 kbps 34.666 kbps 33.333 kbps 32 kbps 30.666 kbps 29.333 kbps 28 kbps ITU-T V.90 ITU-T V.90 ITU-T V.90 ITU-T V.90 ITU-T V.90 ITU-T V.90 ITU-T V.90 ITU-T V.90 ITU-T V.90 ITU-T V.90 ITU-T V.90 ITU-T V.90 ITU-T V.90 ITU-T V.90 ITU-T V.90 ITU-T V.90 ITU-T V.90 ITU-T V.90 ITU-T V.90 ITU-T V.90 ITU-T V.90 ITU-T V.90 Data Rate (upstream) 48 kbps 46.666 kbps 45.333 kbps 44 kbps 42.666 kbps 41.333 kbps 40 kbps 38.666 kbps 37.333 kbps 36 kbps 34.666 kbps 33.333 kbps 32 kbps 30.666 kbps 29.333 kbps 28 kbps 26.666 kbps 25.333 kbps 24 kbps ITU-T V.92 ITU-T V.92 ITU-T V.92 ITU-T V.92 ITU-T V.92 ITU-T V.92 ITU-T V.92 ITU-T V.92 ITU-T V.92 ITU-T V.92 ITU-T V.92 ITU-T V.92 ITU-T V.92 ITU-T V.92 ITU-T V.92 ITU-T V.92 ITU-T V.92 ITU-T V.92 ITU-T V.92 Rev. 1.0 Si2494/39 Table 8. Protocol Characteristics (Continued) Item Specification Data Rate 33.6 kbps 31.2 kbps 28.8 kbps 26.4 kbps 24.0 kbps 21.6 kbps 19.2 kbps 16.8 kbps 14.4 kbps 12.0 kbps 9600 bps 7200 bps 4800 bps 2400 bps 1200 bps 300 bps 300 bps ITU-T V.34 ITU-T V.34 ITU-T V.34 ITU-T V.34 ITU-T V.34 ITU-T V.34 ITU-T V.34 ITU-T V.34 ITU-T V.34 or V.32bis ITU-T V.34 or V.32bis ITU-T V.34 or V.32bis ITU-T V.34 or V.32bis ITU-T V.34 or V.32bis ITU-T V.34, IV.32 bis, or V.22bis ITU-T V.22bis, V.23, or Bell 212A ITU-T V.21 Bell 103 Data Format Bit asynchronous Selectable 8, 9, 10, or 11 bits per character, which includes the start, stop, and parity bits. Compatibility ITU-T V.92, V.90, V.34, V.32bis, V.32, V.23, V.22bis, V.22, V.21, Bell 212A, and Bell 103 Operating Mode Switched network Two-wire full duplex Data Modulation 28 to 56 kbps (downstream) 24 to 48 kbps (upstream) 2.4 to 33.6 kbps 14.4 kbps 12.0 kbps 9600 kbps 9600 kbps 7200 kbps 4800 kbps 2400 kbps 1200 kbps 0 to 300 kbps V.90 as specified by ITU-T V.92 as specified by ITU-T V.34 as specified by ITU-T 128-level TCM/2400 Baud ±0.01% 64-level TCM/2400 Baud ±0.01% 32-level TCM/2400 Baud ±0.01% 16-level QAM/2400 Baud ±0.01% 16-level TCM/2400 Baud ±0.01% 4-level QAM/2400 Baud ±0.01% 16-level QAM/600 Baud ±0.01% 4-level PSK/600 Baud ±0.01% FSK 0–300 Baud ±0.01% Answer Tone ITU-T V.32bis, V.32, V.22bis, V.22, and V.21 modes Bell 212A and 103 modes 2100 Hz ±3 Hz 2225 Hz ±3 Hz Rev. 1.0 15 Si2494/39 Table 8. Protocol Characteristics (Continued) Item Transmit Carrier V.92 V.90 V.34 ITU-T V.32bis ITU-T V.32 ITU-T V.29 ITU-T V.22, V.22bis/Bell 212A Originate mode Answer mode ITU-T V.21 Originate mode Answer mode Bell 103 Originate mode Answer mode Specification As specified by ITU-T As specified by ITU-T As specified by ITU-T 1800 Hz ±0.01% 1800 Hz ±0.01% 1700 Hz ±1 Hz 1200 Hz ±0.5 Hz 2400 Hz ±1 Hz Mark (980 Hz ±12 Hz) Space (1180 Hz ±12 Hz) Mark (1650 Hz ±12 Hz) Space (1850 Hz ±12 Hz) Mark (1070 Hz ±12 Hz) Space (1270 Hz ±12 Hz) Mark (2025 Hz ±12 Hz) Space (2225 Hz ±12 Hz) Output Level Permissive—Switched network Receive Carrier ITU-T V.90 ITU-T V.34 ITU-T V.32bis ITU-T V.32 ITU-T V.29 ITU-T V.22, V.22bis/Bell 212A Originate mode Answer mode ITU-T V.21 Originate mode Answer mode Bell 103 Originate mode Answer mode –9 dBm maximum As specified by ITU-T As specified by ITU-T 1800 Hz ±7 Hz 1800 Hz ±7 Hz 1800 Hz ±7 Hz 2400 Hz ±7 Hz 1200 Hz ±7 Hz Mark (1650 Hz ±12 Hz) Space (1850 Hz ±12 Hz) Mark (1650 Hz ±12 Hz) Space (1850 Hz ±12 Hz) Mark (2025 Hz ±12 Hz) Space (2225 Hz ±12 Hz) Mark (1070 Hz ±12 Hz) Space (1270 Hz ±12 Hz) Carrier Detect (level for ITU-T V.22bis, V.22, V.21, 212, 103) in Switched Network Acquisition (–43 dBm) Release (–48 dBm) Hysteresis 2 dBm minimum ITU-T V.90, V.34, V.32/V.32bis are echo canceling protocols that use signal quality as criteria for maintaining connection. They also provide for self-training detection to force disconnect. 16 DTE Interface EIA/TIA-232-E (ITU-T V.24/V.28/ISO 2110) Line Equalization Automatic Adaptive Connection Options Loss of Carrier in ITU-T V.22bis and lower Rev. 1.0 Si2494/39 Table 8. Protocol Characteristics (Continued) Item Specification Phone Types 500 (rotary dial), 2500 (DTMF dial) Dialing Pulse and Tone DTMF Output Level Per Part 68 Pulse Dial Ratio Make/Break: 39/61% Ring Cadence On 2 seconds; Off 4 seconds Call Progress Monitor BUSY CONNECT (rate) NO ANSWER NO CARRIER NO DIALTONE OK RING RINGING Rev. 1.0 17 Si2494/39 4. Functional Description XTI UART Interface Data Bus C1 DAA Interface C2 Si3018/10 EEPROM Interface DSP EESD EECLK EECS RXD TXD CTS RTS DCD ESC RI XTO PLL Clocking Controller CLKOUT To Phone Line AOUT CS WR RD A0 D0-D7 MISO MOSI SCLK SS Parallel Interface ROM Program Bus RAM SPI Interface INT RESET Figure 6. Functional Block Diagram ® The Si2494/39 ISOmodem is a complete embedded modem chipset with integrated direct access arrangement (DAA) that provides a programmable line interface to meet global telephone line requirements. This solution includes a DSP data pump, modem controller, on-chip RAM and ROM, codec, DAA, analog output, and a PLL clocking generator. The Si2494/39 accepts standard modem AT commands and provides connect rates up to 56/33.6/14.4/2.4 kbps fullduplex over the Public Switched Telephone Network (PSTN). The Si2494/39 features a complete set of modem protocols including all ITU-T standard formats up to V.92. The Si2494/39 features a direct interface to the Si3000 voice codec. Itself a highly integrated device, the Si3000 provides a codec, mixer, digital gain control, microphone preamp, microphone bias generator, speaker driver, and line in/out ports for use with external amplifiers. The Si3000 codec combined with the features of the on-chip DSP supports a voice handset and/or full-duplex speakerphone including programmable levels, frequency response, limiting/soft-clipping and sidetone generation. Voice pass-through with optional compression supports implementation of a tapeless answering machine (TAM), music-on-hold, voice menus, etc. The ISOmodem provides numerous additional features for embedded modem applications. The modem includes full type I and type II caller ID detection and decoding for global standards, DTMF tone generation and detection, Short Message Service (SMS), distinctive ring detection, and call progress monitoring via a PWM audio output. Call progress monitoring is supported through standard result codes. The modem is also programmable to meet global settings. Because the Si2494/39 ISOmodem integrates the DAA, analog features, such as parallel phone detect, overcurrent detection, and global PTT compliance with a single design, are included. 18 Rev. 1.0 Si2494/39 This device is ideal for embedded modem applications due to its small board space, low power consumption, and global compliance. The Si2494/39 solution includes a silicon DAA using Silicon Laboratories’ proprietary thirdgeneration DAA technology. This highly-integrated DAA can be programmed to meet worldwide PTT specifications for ac termination, dc termination, ringer impedance, and ringer threshold. In addition, the Si2494/39 has been designed to meet the most stringent worldwide requirements for out-of-band energy, billing-tone immunity, surge immunity, and safety requirements. The Si2494/39 allows for rapid integration into existing modem applications by providing a serial interface that can directly communicate to either a microcontroller via a UART interface or a PC via an RS-232 port. This interface allows for PC evaluation of the modem immediately upon powerup via the AT commands using standard terminal software. 4.1. Host Interface The Si2494/39 interfaces to the host processor through either an asynchronous serial interface, a synchronous Serial Peripheral Interface (SPI), or a parallel interface. The default is asynchronous serial communication. Selection of either SPI or parallel interface is done on power-up with reset strapping. Please refer to “AN93: ISOmodem® Chipset Family Designer's Guide” for details. 4.1.1. Asynchronous Serial Interface The Si2494/39 supports asynchronous serial communication with data terminal equipment (DTE) at rates up to 307.2 kbps with the standard serial UART format. Upon powerup, the UART baud rate is automatically detected using the autobaud feature. 4.1.2. Serial Peripheral Interface (SPI) The serial peripheral interface (SPI) provides a flexible synchronous serial bus for host processor and Si2494/39 ISOmodem communication. When the Si2494/39 is powered up with SPI mode enabled the modem becomes an SPI slave, and the pins are configured to SS (slave select input, active low), MOSI (serial data input to modem), MISO (serial data output from modem) and SCLK (serial data clock input). Each SPI operation consists of a control-and-address byte and a data byte. 4.1.3. Parallel Interface The Si2494/39 can also communicate via a parallel interface. The parallel interface is an 8-bit data bus with a single bit address to memory mapped registers. Rev. 1.0 19 Si2494/39 4.2. Command Mode Upon reset, the ISOmodem® is in command mode and accepts “AT” commands. An outgoing modem call can be made using the “ATDT#” (tone dial) or “ATDP#” (pulse dial) command after the device is configured. If the handshake is successful, the modem responds with the response codes detailed in Table 14 on page 49 and enters data mode. 4.3. Data Mode The Si2494/39 ISOmodem is in data mode while it has a telephone line connection to another modem or is in the process of establishing a connection. Data protocols are available to provide error correction to improve reliability (V.42 and MNP2-4) and data compression to increase throughput (V.44, V.42bis and MNP5). Each connection between two modems in data mode begins with a handshaking sequence. During this sequence, the modems determine the line speed, data protocol, and related parameters for the data link. Configuration through AT commands determines the range of choices available to the modem during the negotiation process. 4.4. Fast Connect The Si2494/39 supports a fast connect mode of operation to reduce the time of a connect sequence in originate mode. The Fast Connect modes can be enabled for V.21, V.22, Bell103, and V.29 modulations. See AN93 for details. 4.5. V.80 Synchronous Access Mode The Si2494/39 supports a V.80 synchronous access mode of operation, which operates with an asynchronous DTE and a synchronous DCE. See “AN93: ISOmodem® Chipset Family Designer's Guide”. 4.6. Voice Mode (+FCLASS=8) The Si2494/39 supports the implementation of voice handset, tapeless answering machine (TAM), and speakerphone functions when used with the Si3000 voice codec. The Si3000 provides a direct interface to most handsets, including a variable gain microphone preamplifier, microphone bias for an electret (condenser) microphone, digital volume control, and a speaker driver. Additional Line In/Out ports can be used with external amplifiers to support other audio sources/destinations, such as a microphone and speaker for hands-free operation. Very few external components are required between the handset and the Si3000. See the Si3000 Voiceband Codec with Microphone/Speaker Drive data sheet and AN93 Modem Designer’s Guide for more details ITU-T V.253 commands are used to control operation in voice mode. Voice mode is enabled by the AT command +FCLASS=8. The Si2494 /39 DSP provides programmable soft transmit level limiters, programmable transmit and receive gains, sidetone gain, and programmable transmit and receive filters for frequency shaping. These features provide a completely programmable voice implementation capable of compliance with the international standards including TBR 38 and EIA/TIA-470. Voice mode is typically the system’s idle state. While in this state, the ISOmodem monitors the telephone line for various events, such as DTMF detection, caller ID, or ringing (including distinctive ring). Once an event is detected, the ISOModem sends the host either a simple event code (a single character) or a complex event code (multiple characters) preceded by a character to the host. For a full list of event reports, see Table 9 on page 22. In voice mode, the ISOmodem can generate DTMF and single tones using the +VTS command; the +VLS command is used to enable event reporting and tone generation and to control the on/off hook state. Table 9 on page 22 lists the events that are supported based on the +VLS state. 4.7. Clocking The Si2494/39 contains an on-chip phase-locked loop (PLL) and clock generator to derive all necessary internal system clocks from a single clock input. A 32.768 kHz or 4.9152 MHz crystal can be used across XTALI and XTALO pins to form the master clock (±100 ppm max, ±25 ppm recommended) for the ISOmodem. The 32.768 kHz option can provide lower BOM costs and smaller footprint. Alternatively, a clock input of 27 MHz or 4.9152 MHz can be provided to XTALI if that clock source is available in the system. A 4.9152 MHz clock input is the default clock option. Other clock options are selected at power-up through reset strapping. Refer to AN93 for details. 20 Rev. 1.0 Si2494/39 4.8. Low-Power Modes The Si2494/39 provides multiple low power modes. Using the S24 S-register, the Si2494/39 can be set to automatically enter sleep mode after a pre-programmed time of inactivity with either the DTE or the remote modem. The sleep mode is entered after (S24) seconds have passed since the last DTE activity, after the transmit FIFO is empty, and after the last data are received from the remote modem. Additionally, the Si2494/39 can be placed in wake-on-ring-mode using the command, AT&Z. In either mode, the ISOmodem remains in the sleep state until one of the following occurs:  A 1-to-0 transition on TXD (UART mode).  A 1-to-0 transition on SS (SPI mode).  A 1-to-0 transition on CS (parallel mode).  An incoming ring is detected.  A parallel telephone is picked up.  Line polarity reversal The Si2494/39 may also be placed in a complete powerdown mode. Once the Si2494/39 completely powers down, it can only be powered back on via the RESET pin. 4.9. Data Compression The modem can achieve DTE (host-to-ISOmodem) speeds greater than the maximum DCE (modem-to-modem) speed through the use of a data compression protocol. The compression protocols available are the ITU-T V.44, V.42bis, and MNP5 protocols. Data compression attempts to increase throughput by compressing the data before actually sending it. Thus, the modem is able to transmit more data in a given period of time. 4.10. Error Correction The Si2494/39 ISOmodem can employ error correction (reliable) protocols to ensure error-free delivery of asynchronous data sent between the host and the remote end. The Si2494/39 supports V.42 and MNP2-4 error correction protocols. V.42 (LAPM) is most commonly used and is enabled by default. 4.11. Wire Mode Wire mode is used to communicate with standard non-error correcting modems. When optioned with \N3, the Si2494/39 falls back to wire mode if it fails in an attempt to negotiate a V.42 link with the remote modem. Error correction and data compression are not active in wire mode. Rev. 1.0 21 Si2494/39 Table 9. V.253 Event Reporting in Voice Mode Event Description Reporting +VLS Caller Id Report Complex 0,4,20,21 Distinctive Ringing Complex 0,4,20,21 R 0,4,20,21 1-9,A-D,*,# 1,5,20,21 Facsimile Calling (e.g. 1100 Hz) c 1,5,20,21 Data Calling (e.g. 1300 Hz) e 1,5,20,21 Presumed End of Message (QUIET) Time-out q 1,5,20,21 Loop Current Interruption l 1,5,20,21 Ringing Tone r 1,5,20,21 BUSY b 1,5,20,21 DIALTONE d 1,5,20,21 Extension Phone On-hook p 0,1,4,5,20,21 Extension Phone Off-hook P 0,1,4,5,20,21 Facsimile or Data Answer (e.g. 2100 Hz) a 1,5,20,21 Data Answer (e.g. 2225 Hz) f 1,5,20,21 RING DTMF Received 4.12. V.92 PCM Upstream The Si2494/39 supports the ITU-V.92 PCM upstream data protocol. This protocol allows the ISOmodem to connect at speed up to 48 kbps upstream. Previously the upstream connection rate was limited to 33.6 kbps. The PCM upstream mode is enabled by default; to disable, issue the AT command +PIG = 1 (see Table 10 on page 27). To view both downstream and upstream connect speeds in the connect result message, issue the command “AT \V4” or “AT+MR”. 4.13. V.92 Quick Connect The Si2494/39 supports the ITU-V.92 quick connect protocol. Quick connect enables the modem to save and reuse line condition parameters to reduce startup negotiation time. The quick connect feature is enabled by default in the Si2494/39. For information on changing the quick connect settings, see the +PSS and +PQC commands shown in Table 10 on page 27. 4.14. V.92 Modem-on-Hold The modem-on-hold (MOH) feature allows the modem user to answer an incoming call while connected online without dropping the internet connection. The modem will remain “on hold” for a period of time determined by the host and the ISP. There are four AT commands that control the operation of MOH. The commands are as follows: +PCW, +PMH, +PMHT, +PMHR. By changing these parameters, the user can enable/disable call waiting and MOH, set the MOH request timeout, and set the MOH initiate timeout. For further details and syntax on these commands see Table 10 on page 27. The MOH feature is most useful when the Si2494/39 is connected to a central office that allows call waiting. 22 Rev. 1.0 Si2494/39 4.15. Caller ID Operation The Si2494/39 supports full type I and type II caller ID detection and decode. Caller ID is supported for the US Bellcore, European ETSI, UK, and Japanese protocols and is enabled via the +VCID, +VCDT, and +PCW commands. 4.16. Parallel Phone Detection The ISOmodem® is able to detect when another telephone, modem, or other device is using the phone line. This allows the host to avoid interrupting another phone call when the phone line is already in use and to intelligently handle an interruption when the ISOmodem is using the phone line. 4.16.1. On-Hook Line-in-use Detection When the ISOmodem is sharing the telephone line with other devices, it is important that it not interrupt a call in progress. To detect whether another device is using the shared telephone line, the host can use the ISOmodem to monitor the TIP-RING dc voltage with the line voltage sense (LVS) register (U6C, bits 15:8). The LVS bits have a resolution of 1 V per bit with an accuracy of approximately ±10%. Bits 0 through 6 of this 8-bit signed twos complement number indicate the value of the line voltage, and the sign bit (bit 7) indicates the polarity of TIP and RING. The ISOmodem can also monitor the TIP-RING dc voltage using the LVCS register (U79, bits 4:0). See Figure 7 on page 23. See also the %Vn commands for automatic line-in-use detection. 4.16.2. Off-Hook Intrusion Detection When the ISOmodem is off-hook, an algorithm is implemented in the ISOmodem to automatically monitor the TIPRING loop current via the LVCS register. During the off-hook state, the LVCS register switches from representing the TIP-RING voltage to representing the TIP-RING current. See Figure 8 on page 24. Upon detecting an intrusion, the ISOmodem alerts the host of the condition via the INT pin. 30 25 20 LVC S BITS 15 10 5 0 0 3 6 9 12 15 18 21 24 28 30 33 36 39 42 45 47 51 54 57 60 63 66 69 72 75 78 81 84 87 100 Loop Voltage (V) Figure 7. Loop Voltage Rev. 1.0 23 Si2494/39 Overload 30 25 CTR21 only 20 LVCS BITS 15 10 5 0 0 3 6 9 12 15 18 21 24 27 30 33 36 39 42 45 48 51 54 57 60 63 66 69 72 75 78 81 84 87 90 93 140 Loop Current (mA) Figure 8. Loop Current 4.17. Overcurrent Detection The Si2494/39 includes an overcurrent detection feature that measures the loop current at a programmable time after the Si2494/39 goes off-hook. This allows the Si2494/39 to detect if it is connected to an improper telephone line. The overcurrent detection feature may be enabled by setting the OCDM bit (U70, bit 11). OHT (U77, bits 8:0) sets the delay after off-hook until the loop current is measured. See “AN93: ISOmodem® Chipset Family Designer's Guide” for details. 4.18. Global Operation The Si2494/39 chipset contains an integrated silicon direct access arrangement (Silicon DAA) that provides a programmable line interface to meet international telephone line interface requirements. “AN93: Modem Designer’s Guide” gives the DAA register settings required to meet international PTT standards. Additionally, the user-access registers (via the AT:U and AT:R commands) may be programmed for country-specific settings, such as dial tone, ring, ringback, and busy tone. See AN93 for complete details. 4.19. Firmware Upgrades The Si2494/39 contains an on-chip program ROM that includes the firmware required for the features listed in this data sheet. In addition, the Si2494/39 contains on-chip program RAM to accommodate minor changes to the ROM firmware. This allows Silicon Labs to provide future firmware updates to optimize the characteristics of new modem designs and those already deployed in the field. See AN93 for complete details. 4.20. DTMF Detection / Generation The Si2494/39 provides comprehensive DTMF tone generation and detection. The ISOmodem can generate single tones or DTMF tones using the +VTS command. DTMF tones may also be generated during dialing using the “ATDT” command. DTMF detection is only available in voice mode (FCLASS = 8). DTMF digits are reported from the modem to the host using shielding. 24 Rev. 1.0 Si2494/39 4.21. SMS/MMS Support Short Message Service (SMS) is a service that allows text messages to be sent and received from one telephone to another via an SMS service center. Multimedia Messaging Service (MMS) extends the core SMS capability to send messages that include multimedia content. The Fax ISOmodem provides an interface that offers a great deal of flexibility in handling multiple SMS standards. This flexibility is possible because most of the differences between standards are handled by the host using the raw data itself. The Si2494/39 performs the necessary modulation/ demodulation of the data and provides two options for message packet structure (Protocol 1 and Protocol 2, as defined in ETSI ES 201 912). The rest of the data link layer and transfer layer are defined by the host system. The content of the message is entirely up to the host including any checksum or CRC. ETSI ES 201 912 describes two standard data and transfer layers that are commonly used. SMS typically relies on caller identification information to determine if the call should be answered using an SMS device or not. See “6.4. SMS Support” in AN93 for more information on how to configure the modem for SMS support. 4.22. Codec Interface In order to support a full range of voice and data applications, the Si2494/39 includes an optional serial interface that connects to an external voice codec (Si3000). See AN93 for complete details. 4.23. Answering Machine Support The TAM voice compression support includes the following formats:  Signed linear 8-bit, 64 kbps  Unsigned linear 8-bit, 64 kbps  G.711 -law 8-bit, 64 kbps  G.711 A-law 8-bit, 64 kbps  G.726 ADPCM 2-bit, 16 kbps  G.726 ADPCM 4-bit, 32 kbps All formats use a fixed 8 kHz sampling rate. For most applications, the user wants a high-quality message format (64 kbps) for the Outgoing Message (OGM) and is less concerned about the Incoming Message (ICM) quality. Higher compression results in less memory use. Less compression results in higher speech quality. See AN 93 for details. This section covers the functional operation of handset, TAM, and speakerphone modes and includes use cases with the programming examples. 4.24. Voice Pass-Through (Speakerphone) Voice pass-through operation employs an acoustical echo canceller (AEC), acoustical echo suppressor (AES), double-talk detector (DTD), and line echo canceller (LEC). They provide the following performance:  Programmable echo tail filter length: up to 64 ms  Convergence speed (white noise): < 1.6 s  Single-talk echo suppression: > 48 dB  Double-talk echo suppresion: > 30 dB See Appendix of AN93 for details. This section covers the functional operation of handset, TAM, and speakerphone modes and includes use cases with programming examples. 4.25. General-Purpose Tone Detectors Two general-purpose tone detectors based on 4th-order I-quad filters are provided in addition to the other dedicated tone detectors described in this document. These tone detectors are referred to as the Tone A detector and the Tone B detector. They can operate independently or Tone B can receive the output of Tone A to implement a higher-order tone detector. All filter coefficients and detector functions are controlled through U-Registers. These tone detectors are available for use in any operational mode. Whenever an enabled tone detector output transitions, a message will be generated. The messages follow the DLE shielded format for complex reporting. Refer to AN93 for more details. Rev. 1.0 25 Si2494/39 4.26. EEPROM Interface The Si2494/39 supports an optional serial peripheral interface (SPI) bus serial EEPROM Mode 3 with a 16-bit (8– 64 kbit range) address. The EEPROM is intended first for setting custom defaults, second for automatically loading firmware upgrades, and third to allow for user-defined AT command macros for use in custom AT commands or country codes. See AN93 for complete details. 4.27. AT Commands At powerup, the Si2494/39 is in the AT command mode. In command mode, the modem monitors the input (serial or parallel) checking constantly for a valid command (AT commands are described in Table 10.) 26 Rev. 1.0 Si2494/39 Table 10. Basic AT Command Set (Command Defaults in Bold) Command Action $ Display AT command mode settings. A Answer incoming call A/ Dn Re-execute last command. This is the only command not preceded by “AT” or followed by a . Dial The dial command, followed by 1 or more dial command modifiers, manually dials a phone number: Modifier Function ! or & Flash hook switch for FHT (U4F) ms (default: 500 ms) Pause before continuing for S8 seconds (default: , or < 2 seconds) ; Return to AT command mode @ Wait for silence. Polarity reversal detect. By placing the “G” character in the dial string (i.e. ATDTG1), the Si2494/39 will monitor the telephone line for polarity reversals. If a busy tone is detected, the Si2494/39 will report “POLARITY REVERSAL” if a polarity reversal was detected or “NO POLARITY REVERSAL” if a polarity reversal was not detected. In each case, the result code is followed by G “OK”. If the S7 timeout occurs before a busy tone is detected, the Si2494/39 will report “NO CARRIER”. Polarity reversal monitoring begins after the last digit is dialed and ends when the busy tone is detected or S7 timeout occurs. Note: It is not possible to establish a modem connection when using this command. L P T W En Local DTE echo E0 Disable E1 Enable Hn Hook switch. Redial last number. Pulse (rotary) dialing—pulse digits: 0, 1, 2, 3, 4, 5, 6, 7, 8, 9 Tone (DTMF) dialing—DTMF digits: *, #, A, B, C, D, 0, 1, 2, 3, 4, 5, 6, 7, 8, 9. Wait for dial tone before continuing for S14 seconds (default: 12 seconds). Blind dialing modes X0, X1 and X3 do not affect the W command. If the DOP bit (U7A, bit 7) is set, the “ATDTW” command will cause the ISOmodem® to pause dialing and either report an “OK” if a dialtone is detected or “NO DIALTONE” if a dial tone is not detected. Rev. 1.0 27 Si2494/39 Table 10. Basic AT Command Set (Command Defaults in Bold) (Continued) Command H0 Go on-hook (hang up modem). H1 Go off-hook. In Identification and checksum. I0 I1 Display Si2494/39 revision code. A: Revision A Display Si2494/39 firmware revision code (numeric). I7 Display line-side revision code. 18F=Si3018 revision F Display the ISOmodem® model number. “2494” = Si2494 “2439” = Si2439 Diagnostic results 1. See “AN93: ISOModem® Chipset Family Designer’s Guide” for details. I8 Diagnostic results 2. See AN93 for details. Ln Speaker volume operation L1 Low speaker volume L2 Medium speaker volume L3 High speaker volume L4 Very high speaker volume Mn Speaker operation (via AOUT). M0 Speaker is always off. M1 Speaker is on while dialing and handshaking; off in data mode. M2 Speaker is always on. M3 Speaker is off while dialing, on during handshaking and retraining. On Return to data mode from Command mode operation. O0 Return to data mode. O1 Return to data mode and perform a full retrain (at any speed except 300 bps). O2 Return to data mode and perform rate renegotiation. Qn Response mode. Q0 Enable result codes (see Table 14 on page 49) Q1 Disable result codes (enable quiet mode). I3 I6 28 Action R Initiate V.23 reversal. Sn S-register operation (see Table 15 on page 51). S$ List contents of all S registers. Sn? Display contents of S-register n. Sn=x Set S-register n to value x (where n and x are decimal values). Rev. 1.0 Si2494/39 Table 10. Basic AT Command Set (Command Defaults in Bold) (Continued) Command Action Vn Result code type (see Table 14 on page 49). V0 Numeric result codes. V1 Verbal result codes Xn X0 X1 Call Progress Monitor (CPM)—This command controls which CPM signals are monitored and reported to the host from the Si2494/39. (See Table 14 on page 49.) Basic results; disable CPM—Blind dial (does not wait for dial tone). CONNECT message does not include speed. Extended results; disable CPM—Blind dial. CONNECT message includes speed. X3 Extended results and detect dial tone only—Add dial tone detection to X1 mode. Does not blind dial. Extended results and detect busy only—Add busy tone detection to X1 mode. X4 Extended results, full CPM—Full CPM enabled, CONNECT message includes speed. X2 Y0 Extended results—Full CPM enabled including ringback detection. Adds ringback detection to X4 mode. Long space disconnect—Modem hangs up after 1.5 seconds or more of continuous space while on-line. Disable. Y1 Enable. X5 Yn Z :E :I :M :P :R :U Hard Reset—This command is functionally equivalent to pulsing the RESET pin low. (See tAT in Table 5 on page 8.) Read from serial EEPROM. Interrupt Read—This command causes the ISOmodem® to report the lower 8 bits of the interrupt register I/O Control 0 (U70). The CID, OCD, PPD, and RI bits also are cleared, and the INT pin (INT bit in parallel mode) is deactivated on this read. Write to serial EEPROM. Program RAM Write—This command is used to upload firmware supplied by Silicon Labs to the Si2494/39. The format for this command is AT:Paaaa,xxxx,yyyy,.... where aaaa is the first address in hexadecimal and xxxx,yyyy,.... is data in hexadecimal. Only one :P command is allowed per AT command line. No other commands can be concatenated in the :P command line. This command is only for use with special files provided by Silicon Laboratories. Do not attempt to use this command for any other purpose. User-Access Register Read—This command allows the user to read from the user-access registers (see "6. User-Access Registers (U-Registers)" on page 54). The format is “AT:Raa”, where: aa = user-access address in hexadecimal. The “AT:R” command causes all the U- registers to be displayed. User-Access Register Write—This command allows the user to write to the 16-bit useraccess registers. (See page page 54.) The format is “AT:Uaa,xxxx,yyyy,zzzz,...” where aa = user-access address in hexadecimal. xxxx = Data in hexadecimal to be written to location aa. yyyy = Data in hexadecimal to be written to location (aa + 1). zzzz = Data in hexadecimal to be written to location (aa + 2). etc. Rev. 1.0 29 Si2494/39 Table 10. Basic AT Command Set (Command Defaults in Bold) (Continued) Command Action *Y[sequence] Special Access Mode—This command enables special modes and data memory access. [sequence] Description 254:Waaaa,dddd Write hexadecimal data value dddd to hexadecimal data address aaaa. Only one 254:W command per line. 254:Qaaaa Read hexadecimal address aaaa. Returns hexadecimal data value dddd. Only one 254:Q command per line. 2 Enable continuous answer tone for the ATA command. Use ATZ to clear this mode. For example, the single-line, multiple command is AT*Y2A. 1 Enable continuous DTMF tone for first digit used in the ATD command. Use ATZ to clear this mode. For example, the single-line, multiple command for a continuous DTMF “1” digit would be AT*Y1D1. 0 Exit from 254:W or 254:Q access mode. Must reside on a separate line and must be the final sequence be sent after the final 254:W or 254:Q command. +DR=X +DS Options +DS = A +DS = A,B +DS = A,B,C +DS = A,B,C,D Data compression reporting. Mode X 0 Disabled 1 Enabled If enabled, the intermediate result code is transmitted at the point after error control negotiation. The format of this result code is as follows: Result code Mode +DR:NONE Data compression is not in use +DR:V42B Rec. V.42bis is in use in both directions +DR:V42B RD Rec. V.42bis is in use in receive direction only +DR:V42B TD Rec. V.42bis is in use in transmit directions only Controls V.42bis data compression function. A Direction 0 No compression 1 Transmit only 2 Receive only 3 Both Directions B Compression_negotiation 0 Do not disconnect if V.42 is not negotiated. 1 Disconnect is V.42 is not negotiated. C Maximum dictionary size 512 D 30 Maximum string size 6 to 250 (28 default) Rev. 1.0 Si2494/39 Table 10. Basic AT Command Set (Command Defaults in Bold) (Continued) Command Action Controls V.44 data compression function. A Direction 0 No compression 1 Transmit only +DS44 Options 2 Receive only +DS44 = A 3 Both Directions +DS44 = A,B B Compression_negotiation +DS44 = A,B,C 0 Do not disconnect if V.44 is not negotiated. 1 Disconnect if Rec. V.42 is not negotiated. C Capability 0 Stream method Enable synchronous access mode. A Specifies the mode of operation when initiating a modem connection. D Disable synchronous assess mode. 6 Enable synchronous access mode when connection is completed and data state is entered. +ES Options B Specifies fallback mode of operation. +ES = A This parameter should not be used. +ES = A,,C C Specifies the mode of operation when answer a modem connection. D Disable synchronous assess mode. 8 Enable synchronous access mode when connection is completed and data state is entered. Synchronous access mode control options A Specifies action taken if an underrun condition occurs during transparent sub-mode. 0 Modem transmits 8-bit SYN sequences on idle. B Specifies action taken if an underrun condition occurs after a flag during framed submode 0 Modem transmits 8-bit HDLC flags on idle. C Specifies action taken if an underrun or overrun condition occurs after a non-flag during +ESA Options framed sub-mode. +ESA = A 0 Modem transmits abort on underrun in middle of frame. +ESA = A,B 1 Modem transmits flag on underrun in middle of frame and notifies host of underrun +ESA = A,B,C or overrun. +ESA = A,B,C,E Specifies V.34 half duplex operation. +ESA = A,B,C,E,F D This parameter should not be used. +ESA = A,B,C,E,F E Specifies CRC polynomial used while in framed sub-mode. ,G 0 CRC generation checking disable. 1 16-bit CRC generation and checking is performed by the modem. F Specifies NRZI encoding and decoding. 0 NRZI encoding and decoding disabled. G Specifies SYN. 255 Class 1 Mode Enable for V.29 fast connect. X Mode +FCLASS = X 0 Data (limited to configuration only, data calls prohibited) 1 Enables support for Class 1 mode for use in the V.29 fast connect mode. 8 Voice mode Rev. 1.0 31 Si2494/39 Table 10. Basic AT Command Set (Command Defaults in Bold) (Continued) Command +FRM = X +FTM = X 32 Action Class 1 Receive Carrier for V.29 fast connect. X Mode 2 Transmit V.21 (980 Hz) tone for longer than 100 ms, then send answer tone (2100/2225 Hz) for 200 ms. 95 V.29 short synchronous. 96 V.29 full synchronous. Class 1 Transmit Carrier for V.29 fast connect. X Mode 2 Transmit V.21 (980 Hz) tone. 53 Same as &T4, but transmit V.29 7200 bps. Data pattern set by S40 register. AT + FCLASS = 0 must be sent to restore the ISOmodem® to normal operation after test. 54 Same as &T4, but transmit V.29 9600 bps. Data pattern set by S40 register. AT + FCLASS = 0 must be sent to restore the ISOmodem to normal operation after test. 95 V.29 short synchronous. 96 V.29 full synchronous. Rev. 1.0 Si2494/39 Table 10. Basic AT Command Set (Command Defaults in Bold) (Continued) Command +GCI = X Action Country settings - Automatically configure all registers for a particular country. X Country 0 Japan 9 Australia A Austria F Belgium 16 Brazil 1B Bulgaria 20 Canada 26 China 27 Columbia 2E Czech Republic 31 Denmark 35 Ecuador 3C Finland 3D France 42 Germany 46 Greece 50 Hong Kong 51 Hungary 53 India 57 Ireland 58 Israel 59 Italy 61 South Korea 69 Luxembourg 6C Malaysia 73 Mexico 7B Netherlands 7E New Zealand 82 Norway 87 Paraguay 89 Philippines 8A Poland 8B Portugal 9C Singapore 9F South Africa A0 Spain A5 Sweden A6 Switzerland B8 Russia B4 United Kingdom B5 United States FE Taiwan Note: U-registers are configured to Silicon Laboratories’ recommended values. The +GCI command resets the U-registers and the S7 and S6 S-registers to default values before setting countryspecific values. Changes may be made by writing individual registers after sending the AT+GCI command. Refer to “AN93: ISOModem® Chipset Family Designer’s Guide” for details. +GCI? +GCI = ? List current country code setting (response is: + GCI:) List all possible country code settings. Rev. 1.0 33 Si2494/39 Table 10. Basic AT Command Set (Command Defaults in Bold) (Continued) Command +IFC Options +IFC = A +IFC = A,B +ITF Options +ITF = A +ITF = A,B +ITF = A,B,C 34 Action Specifies the flow control to be implemented. A Specifies the flow control method used by the host to control data from the modem 0 None 1 Local XON/OFF flow control. Does not pass XON/XOFF character to the remote modem. 2 Hardware flow control (RTS) B Specifies the flow control method used by the modem to control data from the host 0 None 1 Local XON/OFF flow control. 2 Hardware flow control (CTS). Transmit flow control threshold. A Threshold above which the modem will generate a flow off signal bytes B Threshold below which the modem will generate a flow on signal bytes C Polling interval for indicator 0 to 300 in 10 msec units. +IPR = Fixed DTE Rate. Description 0 Automatically detect the baud rate. [BPS] The decimal value of the rate in bits per second. Note that the parameter represents the DTE rate in bps and may be set to any of the following values: 300, 600, 1200, 2400, 4800, 7200, 9600, 12000, 14400, 19200, 38400, 57600, 115200, 230400, 245760, and 307200. +MR = X Modulation reporting control. X Mode 0 Disabled 1 Enabled If enabled, the intermediate result code is transmitted at the point during connect negotiation. The format of this result code is as follows: +MCR: e.g. +MCR: V32B +MRR: e.g. +MRR: 14400 Rev. 1.0 Si2494/39 Table 10. Basic AT Command Set (Command Defaults in Bold) (Continued) Command Action Modulation Selection. A Preferred modem carrier V21 ITU-T V.21 V22 ITU-T V.22 V22B ITU-T V.22bis V32 ITU-T V.32 +MS Options V32B ITU-T V.32bis +MS = A V34 ITU-T V.34 +MS = A,B V90 ITU-T V.90 +MS = A,B,C V92 ITU-T V.92 +MS = A,B,C,D B Automatic modulation negotiation +MS = A,B,C,D,E 0 Disabled +MS = A,B,C,D,E, 1 Enabled F C,D Min TX rate/Max TX rate are optional numeric values that specify the lowest value at which the DCE may establish a connection. If unspecified (set to 0), they are determined by the carrier and automode settings. E,F Min RX rate/Max RX rate are optional numeric values which specify the highest value at which the DCE may establish a connection. If unspecified (set to 0), they are determined by the carrier and automode settings. Controls the action to be taken upon detection of call waiting. X Mode +PCW = X 0 Toggle RI and collect type II Caller ID if enabled by +VCID. 1 Hang up. 2 Ignore call waiting. +PIG=X Controls the use of PCM upstream in a V.92 DCE. Mode X 0 Enable PCM upstream. 1 Disable PCM upstream. +PMH=X Controls the modem-on-hold procedures. Mode X 0 Enables V.92 MOH. 1 Disables V.92 MOH. +PMHF=X V.92 MOH hook flash. This command causes the DCE to go on-hook and then return offhook. If this command is initiated and the modem is not On Hold, Error is returned. Rev. 1.0 35 Si2494/39 Table 10. Basic AT Command Set (Command Defaults in Bold) (Continued) 36 Command Action +PMHR=X Initiate MOH. Requests the DCE to initiate or to confirm a MOH procedure. Valid only if MOH is enabled. X Mode 0 V.92 MOH request denied or not available. 1 MOH with 10 s timeout granted. 2 MOH with 20 s timeout granted. 3 MOH with 30 s timeout granted. 4 MOH with 40 s timeout granted. 5 MOH with 1 min. timeout granted. 6 MOH with 2 min. timeout granted. 7 MOH with 3 min. timeout granted. 8 MOH with 4 min. timeout granted. 9 MOH with 6 min. timeout granted. 10 MOH with 8 min. timeout granted. 11 MOH with 12 min. timeout granted. 12 MOH with 16 min. timeout granted. 13 MOH with indefinite timeout granted. 14 MOH request denied. Future request will also be denied. +PMHT=X Controls access to MOH request and sets the timeout value. X Mode 0 Deny V.92 MOH request. 1 Grant MOH with 10 s timeout. 2 Grant MOH with 20 s timeout. 3 Grant MOH with 30 s timeout. 4 Grant MOH with 40 s timeout. 5 Grant MOH with 1 min. timeout. 6 Grant MOH with 2 min. timeout. 7 Grant MOH with 3 min. timeout. 8 Grant MOH with 4 min. timeout. 9 Grant MOH with 6 min. timeout. 10 Grant MOH with 8 min. timeout. 11 Grant MOH with 12 min. timeout. 12 Grant MOH with 16 min. timeout. 13 Grant MOH with indefinite timeout. +PQC=X V.92 Phase 1 and Phase 2 Control. X Mode 0 Enable Short Phase 1 and Short Phase 2. 1 Enable Short Phase 1. 2 Enable Short Phase 2. 3 Disable Short Phase 1 and Short Phase 2. +PSS=X Selection of full or short startup procedures. X Mode 0 The DCEs decide to use short startup procedures. 1 Forces the use of short startup procedures on next and subsequent connections. 2 Forces the use of full startup procedures on next and subsequent connections. Rev. 1.0 Si2494/39 Table 10. Basic AT Command Set (Command Defaults in Bold) (Continued) Command +VCDT = X +VCID = X +VCIDR? Action Caller ID Type. X Mode 0 After ring only 1 Always on (Recommended Setting) 2 UK 3 Japan Caller ID Enable. X Mode 0 Off 1 On—formatted 2 On—raw data format Type II caller ID information — The Si2494/39 will display “+VCDIR:” followed by raw caller ID information including checksum. +VDR = n Distinctive Ring. n Mode 0,x Disable distinctive ring 1,0 Enable distinctive ring. The ISOmodem will report DROF and DRON result codes only. DROF and DRON are reported in 100 ms units. 1,x Enable distinctive ring. The ISOmodem will report DROF and DRON result codes as well as well as a RING result code x/10 seconds after the falling edge of a ring pulse. DROF and DRON are reported in 100 ms units. +VGR Receive Gain Selection. The parameter has a range of 112-134 with 128 being the nominal value. This represents a range of -48 dB to 18 dB. The default is 128 (0 dB). This command is used to control the receive gain at the DTE from either the Si3000 Codec or the DAA. The purpose is to adjust the DTE receive gain for the TAM voice stream during idle state. +VGT Transmit Gain Selection. The parameter has a range of 112-134 with 128 being the nominal value. This represents a range of -48 to 18 dB. The default is 128 (0 dB). This command is used to control the transmit gain at the DTE to either the Si3000 Codec or the DAA. The purpose is to adjust the DTE transmit gain for the TAM voice stream during idle state. +VIP Load Voice Factory Defaults. +VIT DTE/DCE Inactivity Timer. The parameter has a range of 0–255 with units of seconds. The default is 0 (disable). Rev. 1.0 37 Si2494/39 Table 10. Basic AT Command Set (Command Defaults in Bold) (Continued) Command Action +VLS = n Analog Source / Destination Select. n Description 0 ISOmodem on-hook. AOUT disabled. Tone detectors disabled. Si3000 sample pass-through to DAA is inactive. 1 ISOmodem off-hook. AOUT disabled. Tone detectors disabled. 4 ISOmodem on-hook. AOUT connected to ISOmodem tone generators. Tone detectors disabled. 5 ISOmodem off-hook. AOUT connected to PSTN. Tone detectors enabled. 15 ISOmodem goes off-hook, begins V.253 tone event reporting and Si3000 to DAA sample pass-through becomes active. Dial tone can be heard on handset. 20 ISOmodem on-hook. AOUT disabled. Tone detectors enabled. 21 ISOmodem on-hook. AOUT connected to ISOmodem tone generators. Tone detectors enabled. +VNH = Automatic Hangup Control. Hook control description 0 The ISOmodem retains automatic hangups as is normal in the other modes (such as hanging up the phone when the ISOmodem does not detect a data carrier with a given time interval). 1 The ISOmodem shall disable automatic hangups in the other non-voice modes. 2 The ISOmodem shall disable all hang-ups in other non-voice modes. The ISOmodem shall only perform a “logical” hangup (return the OK result code). +VRA = n Ringing Tone Goes Away Timer. The ISOmodem only uses this command in call origination transactions. This command sets the amount of time in 0.1 second units the ISOmodem shall wait between Ringing Tone before it can assume that the remote modem has gone off-hook. Default time is five seconds. +VRID = n Repeat Caller ID. n Description 0 Display Caller ID information of the last incoming call in formatted form. 1 Display Caller ID information of the last incoming call in unformatted form. +VRN = n Ringing Tone Never Appeared Timer. This command sets the amount of time in seconds the ISOmodem will wait looking for Ringing Tone. If the ISOmodem does not detect Ringing Tone in this time period, the ISOmodem shall assume that the remote station has gone off-hook and return an OK result code. Default time is 0 seconds. 38 Rev. 1.0 Si2494/39 Table 10. Basic AT Command Set (Command Defaults in Bold) (Continued) Command Action +VRX Receive Voice Stream. Enable DTE receive of voice stream. The DCE will return a CONNECT response followed by the voice stream as defined by the +VSM command. The DTE can issue a or sequence to terminate the receive stream. The DCE will return a followed by an OK response for and followed by an OK response for . The DCE can be configured to terminate the stream using the DTE/DCE Inactivity Timer, which is configured using the +VIT command. The DTE will need to process any shielded events present in the data stream. Any sequences can be preserved to allow less overhead during playback of the stream with the +VTX command. +VSD = , Silence Detection. Noise level sensitivity 127 Less aggressive [more sensitive, lower noise levels considered to be silence]. 128 Nominal level of sensitivity. 129 More aggressive [less sensitive, higher noise levels considered to be silence]. sets the length of a time interval in 0.1 second units, which must contain no or little activity, before the ISOmodem will report (QUIET) (). Default is five seconds. +VSM = n Voice Compression Method. 0 Signed PCM 1 Unsigned PCM 4 G.711 µ-Law 5 G.711 A-Law 129 ADPCM 2-bit (2 kB/s storage) 131 ADPCM 4-bit (4 kB/s storage) +VSP Voice Speakerphone State Description 0 Speakerphone AEC, AES and LEC disabled. Handset FIR filter coefficients are selected. 1 Speakerphone AEC, AES and LEC enabled. Speakerphone FIR filter coefficients are selected. The +VLS=13 command must be used in combination with this setting. +VTD = n DTMF / Tone Duration Timer. This command sets the default DTMF / tone generation duration in 10 ms units for the +VTS command. Default time is 1 second (n = 100). Rev. 1.0 39 Si2494/39 Table 10. Basic AT Command Set (Command Defaults in Bold) (Continued) Command Action +VTS = [, , ] DTMF and Tone Generation. This command can be used to produce DTMF tones, single-frequency tones, and doublefrequency tones. Note that the bracket characters are required for correct operation. Frequency one, which has a range of 0, 200-3200 Hz. Frequency two, which has a range of 0, 200-3200 Hz. Duration of the tone(s) in 10 ms units. +VTX Transmit Voice Samples. Used for sending digitized voice samples from host memory through the UART interface. The +VSM command determines the format of the samples. Multiple routing options are available. 40 Rev. 1.0 Si2494/39 4.28. Extended AT Commands The extended AT commands are supported by the Si2494/39 and are described in Tables 11 through 13. Table 11. Extended AT& Command Set (Command Defaults in Bold) Command &$ Action Display AT& current settings. &D0 ESC is not used &D1 ESC escapes to command mode from data mode if also enabled by HES U70, bit 15. &D2 ESC assertion during a modem connection causes the modem to go on-hook and return to command mode. &D3 ESC assertion causes ATZ command (reset and return OK result code). &F Restore factory default settings. &Gn Line connection rate limit—This command sets an upper limit on the line speed that the Si2494/39 can connect. Note that the &Hn commands may limit the line speed as well (&Gn not used for &H0 or &H1). Not all modulations support rates given by &G. Any improper setting will be ignored. &G3 1200 bps max &G4 2400 bps max &G5 4.8 kbps max &G6 7.2 kbps max &G7 9.6 kbps max &G8 12 kbps max &G9 14.4 kbps max &G10 16.8 kbps max &G11 19.2 kbps max &G12 21.6 kbps max &G13 24 kbps max &G14 26.4 kbps max &G15 28.8 kbps max &G16 31.2 kbps max &G17 33.6 kbps max &Hn Switched network handshake mode—&Hn commands must be on a separate command line from ATD, ATA, or ATO commands. &H0 V.90 with automatic fallback (56 kbps to 300 bps) &H1 V.90 only (56 kbps to 28 kbps) Rev. 1.0 41 Si2494/39 Table 11. Extended AT& Command Set (Command Defaults in Bold) (Continued) Command 42 Action &H2 V.34 with automatic fallback (33.6 kbps to 300 bps) &H3 V.34 only (33.6 kbps to 2400 bps) &H4 ITU-T V.32bis with automatic fallback (14.4 kbps to 300 bps) &H5 ITU-T V.32bis only (14.4 kbps to 4800 bps) &H6 ITU-T V.22bis only (2400 bps or 1200 bps) &H7 ITU-T V.22 only (1200 bps) &H8 Bell 212 only (1200 bps) &H9 Bell 103 only (300 bps) &H10 ITU-T V.21 only (300 bps) &H11 V.23 (1200/75 bps) &H12 V.92 with automatic fallback &Pn Japan pulse dialing &P0 Configure Si2494/39 for 10 pulse-per-second pulse dialing. For Japan. &P1 Configure Si2494/39 for 20 pulse-per-second pulse dialing. For Japan. &Tn Test mode &T0 Cancel test mode (Escape to command mode to issue AT&T0). This command will also report the number of bit errors encountered on the previous &T4 or &T5 test. &T2 Initiate ITU-T V.54 (ANALOOP) test. Modulation set by &H AT command. Test loop is through the DSP (Si2494/39 device) only. ISOmodem® echoes data from TX pin (Register 0 in parallel mode) back to RX pin (Register 0 in parallel mode). &T3 Initiate ITU-T V.54 (ANALOOP) test. Modulation set by &H AT command. Test loop is through the DSP (Si2494/39), DAA interface section (Si2494/39), DAA interface (Si3018), and analog hybrid circuit (Si3018). ISOmodem echoes data from TX pin (Register 0 in parallel mode) back to RX pin (Register 0 in parallel mode). Phone line termination required as in Figure 1. To test only the link operation, the hybrid and AFE codec can be removed from the test loop by setting the DL bit (U62, bit 1). &T4 Initiate transmit as originating modem with automatic data generation. Modulation, data rate, and symbol rate are set by &H, &G, and S41. Data pattern is set by the S40 register. Continues until the ATH command is sent after an escape into command mode. Data is also demodulated as in ANALOOP, and any bit errors are counted to be displayed after the test using &T0. &T5 Initiate transmit as answering modem with automatic data generation. Modulation, data rate, and symbol rate are set by &H, &G, and S41. Data pattern is set by the S40 register. Continues until the ATH command is sent after an escape into command mode. Data is also demodulated as in ANALOOP, and any bit errors are counted to be displayed after the test using &T0. &T6 Compute checksum for firmware-upgradeable section of program memory. If no firmware upgrade is installed, &T6 returns 0x4474. Rev. 1.0 Si2494/39 Table 11. Extended AT& Command Set (Command Defaults in Bold) (Continued) Command Action &Xn Automatic determination of telephone line type. &X0 Abort &x1 or &x2 command. &X1 Automatic determination of telephone line type. Result code: WXYZn W: 0 = line supports DTMF dialing. 1 = line is pulse dial only. X: 0 = line supports 20 pps dialing. 1 = line supports 10 pps dialing only. Y: 0 = extension network present (PBX). 1 = outside line (PSTN) connected directly. Z: 0 = continuous dialtone. 1 = make-break dialtone. n: 0–9 (number required for outside line if Y = 0). Note: The initial number attempted for an outside line is controlled in S51. &X2 *Y2A &Z Same as &X1, but Y result (PBX) is not tested. Produce a constant answer tone (ITU-T) and return to command mode. The answer tone continues until the ATH command is received or the S7 timer expires. Enter low-power wake-on-ring mode. Rev. 1.0 43 Si2494/39 Table 12. Extended AT% Command Set (Command Defaults in Bold) Command Action %$ Display AT% command settings. %B Report blacklist. See also S42 register. %Cn Data compression %C0 Disable V.42bis and MNP5 data compression %C1 Enable V.42bis in transmit and receive paths. If MNP is selected (\N2), then %C1 enables MNP5 in transmit and receive paths. %C2 Enable V.42bis in transmit path only. %C3 Enable V.42bis in receive path only. %On Answer mode. %O1 Si2494/39 will auto-answer a call in answer mode. %O2 Si2494/39 will auto-answer a call in originate mode. %Vn Automatic Line Status Detection. After the %V1 and %V2 commands are issued, the Si2494/39 will automatically check the telephone connection for whether or not a line is present. If a line is present, the Si2494/39 will automatically check if the line is already in use. Finally, the Si2494/39 will check line status both before going offhook and again before dialing. %V1 uses the fixed method, and %V2 uses the adaptive method. %V0 (default) disables this feature. %V0 Disable automatic line-in-use detection. %V1 Automatic Line Status Detection—Fixed Method. Description: Before going off-hook with the ATD, ATO, or ATA commands, the Si2494/39 compares the line voltage (via LVCS) to registers NOLN (U83) and LIUS (U84): Loop Voltage 0  LVCS  NOLN NOLN  LVCS  LIUS LIUS  LCVS Action Report “NO LINE” and remain on-hook. Report “LINE IN USE” and remain on-hook. Go off-hook and establish a modem connection. Once the call has begun, the off-hook intrusion algorithm (described in "4.16.2. Off-Hook Intrusion Detection" on page 23) operates normally. In addition, the Si2494/39 will report “NO LINE” if the telephone line is completely disconnected. If the HOI bit (U77, bit 11) is set, “LINE IN USE” is reported upon intrusion. 44 Rev. 1.0 Si2494/39 Table 12. Extended AT% Command Set (Command Defaults in Bold) (Continued) Command Action %V2 Automatic Line Status Detection—Adaptive Method. Description: Before going off-hook with the ATD, ATO, or ATA commands, the Si2494/39 compares the line voltage (via LVCS) to the NLIU (U85) register: Loop Voltage Action 0  LVCS  (0.0625 x NLIU) Report “NO LINE” and remain on-hook. (0.0625 x NLIU) < LVCS  (0.85 x NLIU) Report “LINE IN USE” and remain on-hook. (0.85 x NLIU) < LCVS Go off-hook and establish a modem connection. The NLIU register is updated every 1 ms with the minimum non-zero value of LVCS in the last 30 ms. This allows the Si2494/39 to eliminate errors due to 50/60 Hz interference and also adapt to relatively slow change in the on-hook dc reference value on the telephone line. This algorithm does not allow any non-zero values for NLIU below 0x0007. The host may also initialize NLIU prior to issuing the %V2 command. Once the call has begun, the off-hook intrusion algorithm (described in "4.16.2. Off-Hook Intrusion Detection" on page 23) operates normally. In addition, the Si2494/39 will report “NO LINE” if the telephone line is completely disconnected. If the HOI (U77, bit 11) bit is set, “LINE IN USE” is reported upon intrusion. Rev. 1.0 45 Si2494/39 Table 13. Extended AT\ Command Set (Command Defaults in Bold) Command \$ Action Display AT\ command settings. \Bn Character length will be automatically set in autobaud mode \B0 6N1—six data bits, no parity, one stop bit, one start bit, eight bits total (\N0 only)1 \B1 7N1—seven data bits, no parity, one stop bit, one start bit, nine bits total (\N0 only)1 \B2 7P1—seven data bits, parity optioned by \P, one stop bit, one start bit, 10 bits total \B3 8N1—eight data bits, no parity, one stop bit, one start bit, 10 bits total \B5 8P1—eight data bits, parity optioned by \P, one stop bit, one start bit, 11 bits total (\N0 only) \B6 8X1—eight data bits, one escape bit, one stop bit, one start bit, 11 bits total (enables ninth-bit escape mode) \Nn Asynchronous protocol \N0 Wire mode (no error correction, no compression) \N2 MNP reliable mode. The Si2494/39 attempts to connect with the MNP protocol. If unsuccessful, the call is dropped. \N3 V.42 auto-reliable—The Si2494/39 attempts to connect with the V.42 protocol. If unsuccessful, the MNP protocol is attempted. If unsuccessful, wire mode is attempted. \N4 V.42 (LAPM) reliable mode (or drop call)—Same as \N3 except that the Si2494/39 drops the call instead of connecting in MNP or wire mode. \N5 V.42 and MNP reliable mode—The Si2494/39 attempts to connect with V.42. If unsuccessful, MNP is attempted. If MNP us unsuccessful, the call is dropped. \Pn Parity type will be automatically set in autobaud mode \P0 Even \P1 Space1 \P2 Odd \P3 Mark1 \Qn Modem-to-DTE flow control \Q0 Disable all flow control—This may only be used if the DTE speed and the VF speed are guaranteed to match throughout the call. \Q2 Use CTS only Notes: 1. When in autobaud mode, \B0, \B1, and \P1 will not be detected automatically. The combination of \B2 and \P3 will be detected. This is compatible with seven data bits, no parity, two stop bits. Seven data bits, no parity, one stop bit may be forced by sending AT\T17\B1. 2. The autobaud feature does not detect this rate. 3. Default is \T9 if a pulldown resistor is connected to the autobaud strap pin; otherwise, the default is \T16. 46 Rev. 1.0 Si2494/39 Table 13. Extended AT\ Command Set (Command Defaults in Bold) (Continued) Command Action \Q3 Use RTS/CTS \Q4 Use XON/XOFF flow control for modem-to-DTE interface. Does not enable modem-to-modem flow control. \Tn DTE rate—Change DTE rate. When the Si2494/39 is configured in autobaud mode (default), \T0 through \T15 will lock the new baud rate and disable autobaud. When the ISOmodem® is not in autobaud mode (the autobaud strap pin low on powerup), the result code “OK” is sent at the old DTE rate. Subsequent commands must be sent at the new rate. \T0 300 bps \T1 600 bps \T2 1200 bps \T3 2400 bps \T4 4800 bps \T5 7200 bps \T6 9600 bps \T7 12.0 kbps2 \T8 14.4 kbps \T9 19.2 kbps3 \T10 38.4 kbps \T11 57.6 kbps \T12 115.2 kbps \T13 230.4 kbps \T14 245.760 kbps2 \T15 307.200 kbps \T16 Autobaud on3 \T17 Autobaud off; lock at current baud rate. Notes: 1. When in autobaud mode, \B0, \B1, and \P1 will not be detected automatically. The combination of \B2 and \P3 will be detected. This is compatible with seven data bits, no parity, two stop bits. Seven data bits, no parity, one stop bit may be forced by sending AT\T17\B1. 2. The autobaud feature does not detect this rate. 3. Default is \T9 if a pulldown resistor is connected to the autobaud strap pin; otherwise, the default is \T16. Rev. 1.0 47 Si2494/39 Table 13. Extended AT\ Command Set (Command Defaults in Bold) (Continued) Command Action \U Serial mode—causes a low pulse (25 ms) on RI and DCD. INT to be the inverse of ESC. RTS to be inverse of CTS. Parallel mode—causes a low pulse (25 ms) on INT. This command terminates with a RESET. \Vn Connect message type \V0 Report connect message and protocol message \V2 Report connect message only (exclude protocol message) \V4 Report connect and protocol message with both upstream and downstream connect rates. Notes: 1. When in autobaud mode, \B0, \B1, and \P1 will not be detected automatically. The combination of \B2 and \P3 will be detected. This is compatible with seven data bits, no parity, two stop bits. Seven data bits, no parity, one stop bit may be forced by sending AT\T17\B1. 2. The autobaud feature does not detect this rate. 3. Default is \T9 if a pulldown resistor is connected to the autobaud strap pin; otherwise, the default is \T16. 48 Rev. 1.0 Si2494/39 Table 14. Result Codes Numeric Meaning Verbal Response X0 X1 X2 X3 X4 X5 0 Command was successful OK X X X X X X 1 Link established at 300 bps or higher CONNECT X X X X X X 2 Incoming ring detected RING X X X X X X 3 Link dropped NO CARRIER X X X X X X 4 Command failed ERROR X X X X X X 5 Link establish at 1200 CONNECT 1200 X X X X X 6 Dial tone not present NO DIALTONE X X 7 Line busy BUSY X X X 8 Remote not answering NO ANSWER X X X X X X X 9 Ringback detected RINGING 10 Link established at 2400 CONNECT 2400 X X X X X X 11 Link established at 4800 CONNECT 4800 X X X X X 12 Link established at 9600 CONNECT 9600 X X X X X 14 Link established at 19200 CONNECT 19200 X X X X X 15 Link established at 7200 CONNECT 7200 X X X X X 16 Link established at 12000 CONNECT 12000 X X X X X 17 Link established at 14400 CONNECT 14400 X X X X X 18 Link established at 16800 CONNECT 16800 X X X X X 19 Link established at 21600 CONNECT 21600 X X X X X 20 Link established at 24000 CONNECT 24000 X X X X X 21 Link established at 26400 CONNECT 26400 X X X X X 22 Link established at 28800 CONNECT 28800 X X X X X 23 Link established at 31200 CONNECT 31200 X X X X X 24 Link established at 33600 CONNECT 33600 X X X X X 30 Caller ID mark detected CIDM X X X X X X 31 Hookswitch flash detected FLASH X X X X X X 32 UK CID State Tone Alert Signal detected STAS X X X X X X 33 Overcurrent condition X* X X X X X X 40 Blacklist is full BLACKLIST FULL (enabled via S42 register) X X X X X X 41 Attempted number is blacklisted. BLACKLISTED (enabled via S42 register) X X X X X X 42 No phone line present NO LINE (enabled via %Vn commands) X X X X X X 43 Telephone line is in use LINE IN USE (enabled via %Vn commands) X X X X X X 44 A polarity reversal was detected POLARITY REVERSAL (enabled via G modifier) X X X X X X *Note: X is the only verbal response code that does not follow the Result Code standard. There is no leading . Rev. 1.0 49 Si2494/39 Table 14. Result Codes (Continued) Numeric Meaning Verbal Response X0 X1 X2 X3 X4 X5 X X X X X X 45 A polarity reversal was NOT NO POLARITY REVERSAL detected (enabled via G modifier) 52 Link established at 56000 CONNECT 56000 X X X X X 60 Link established at 32000 CONNECT 32000 X X X X X 61 Link established at 48000 CONNECT 48000 X X X X X 63 Link established at 28000 CONNECT 28000 X X X X X 64 Link established at 29333 CONNECT 29333 X X X X X 65 Link established at 30666 CONNECT 30666 X X X X X 66 Link established at 33333 CONNECT 33333 X X X X X 67 Link established at 34666 CONNECT 34666 X X X X X 68 Link established at 36000 CONNECT 36000 X X X X X 69 Link established at 37333 CONNECT 37333 X X X X X 70 No protocol PROTOCOL: NONE Set with \V0 command. 75 Link established at 75 CONNECT 75 X 77 V.42 protocol PROTOCOL: V42 Set with \V0 command. 79 V.42bis protocol PROTOCOL: V42bis Set with \V0 command. 80 MNP2 protocol PROTOCOL: ALTERNATE, + CLASS 2 Set with \V command. 81 MNP3 protocol PROTOCOL: ALTERNATE, + CLASS 3 Set with \V command. 82 MNP4 protocol PROTOCOL: ALTERNATE, + CLASS 4 Set with \V command. 83 MNP5 protocol PROTOCOL: ALTERNATE, + CLASS 5 X X X X X 90 Link established at 38666 CONNECT 38666 X X X X X 91 Link established at 40000 CONNECT 40000 X X X X X 92 Link established at 41333 CONNECT 41333 X X X X X 93 Link established at 42666 CONNECT 42666 X X X X X 94 Link established at 44000 CONNECT 44000 X X X X X 95 Link established at 45333 CONNECT 45333 X X X X X 96 Link established at 46666 CONNECT 46666 X X X X X 97 Link established at 49333 CONNECT 49333 X X X X X 98 Link established at 50666 CONNECT 50666 X X X X X 99 Link established at 52000 CONNECT 52000 X X X X X 100 Link established at 53333 CONNECT 53333 X X X X X 101 Link established at 54666 CONNECT 54666 102 DTMF dial attempted on a pulse dial only line UN–OBTAINABLE NUMBER X X X X X X X X X X X X X X X *Note: X is the only verbal response code that does not follow the Result Code standard. There is no leading . 50 Rev. 1.0 Si2494/39 5. S-Registers The S command allows reading (Sn?) or writing (Sn = x) the S-registers. The S-registers store values for functions that typically are rarely changed, such as timers or counters, and the ASCII values of control characters, such as carriage return. Table 15 summarizes the S-register set. Table 15. S-Register Description Definition S-Register (Decimal) Function Default (Decimal) Range Units 0 Automatic answer—Number of rings the Si2494/39 must detect before answering a call. 0 disables auto answer. 0 0–255 Rings 1 Ring counter. 0 0–255 Rings 2 ESC code character. 43 (+) 0–255 ASCII 3 Carriage return character. 13 (CR) 0–255 ASCII 4 Linefeed character. 10 (LF) 0–255 ASCII 5 Backspace character. 08 (BS) 0–255 ASCII 6 Dial tone wait timer—Number of seconds the Si2494/ 39 waits before blind dialing. Only applicable if blind dialing is enabled (X0, X1, X3). 02 0–255 seconds 7 Carrier wait timer—Number of seconds the Si2494/39 waits for carrier before timing out. This register also sets the number of seconds the modem waits for ringback when originating a call before hanging up. This register also sets the number of seconds the answer tone will continue while using the AT Y2A command. 80 0–255 seconds 8 Dial pause timer for , and < dial command modifiers. 02 0–255 seconds 9 Carrier presence timer—Time after a loss of carrier that a carrier must be detected before reactivating DCD. S9 is referred to as “carrier loss debounce time.” 06 1–255 0.1 second 10 Carrier loss timer—Time the carrier must be lost before the Si2494/39 disconnects. Setting 255 disables disconnect entirely. If S10 is less than S9, even a momentary loss of carrier causes a disconnect. 14 1–255 0.1 second 12 Escape code guard timer—Minimum guard time required before and after “+++” for the Si2494/39 to recognize a valid escape sequence. 50 1–255 0.02 second 14 Wait for dial tone delay value (in relation to the W dial modifier). Starts when “W” is executed in the dial string. 12 0–255 seconds * Rev. 1.0 51 Si2494/39 Table 15. S-Register Description (Continued) Definition S-Register (Decimal) Function Default (Decimal) Range Units 24 Sleep Inactivity Time—Sets the time that the modem operates in normal power mode with no activity on the serial port, parallel port, or telephone line before entering low-power sleep mode. This feature is disabled if the timer is set to 0. 0 0–255 seconds 30 Disconnect Activity Timer—Sets the length of time that the modem stays online before disconnecting with no activity on the serial port, parallel port, or telephone line (Ring, hookswitch flash, or caller ID). This feature is disabled if set to 0. 0 0–255 minutes 38 Hang Up Delay Time—Maximum delay between receipt of ATH0 command and hang up. If time out occurs before all data can be sent, the NO CARRIER (3) result code is sent (operates in V.42 mode only). “OK” response is sent if all data is transmitted before timeout. S38 = 255 disables timeout and modem disconnects only if data is successfully sent or carrier is lost. 20 0–255 seconds 40 Data Pattern—Data pattern generated during &T4 and &T5 transmit tests. 0 = All spaces (0s) 1 = All marks (1s) 2 = Random data 0 0–2 41 V.34 symbol rate - Symbol rate for V.34 when using the &T4 and &T5 commands. 0 = 2400 symbols/second 1 = 2743 symbols/second 2 = 2800 symbols/second 3 = 3000 symbols/second 4 = 3200 symbols/second 5 = 3429 symbols/second A valid combination of symbol rate (S41) and data rate (&G) must be selected. Symbol Rate Allowable Data Rates 2400 2400–21600 2743 4800–26400 2800 4800–26400 3000 4800–28800 3200 4800–31200 3429 4800–33600 0 0–5 52 Rev. 1.0 Si2494/39 Table 15. S-Register Description (Continued) Definition S-Register (Decimal) Function Default (Decimal) Range 42 Blacklisting—The Si2494/39 will not dial the same number more than two times in three minutes. An attempt to dial a third time within three minutes will result in a “BLACKLISTED” result code. If the blacklist memory is full, any dial to a new number will result in a “BLACKLIST FULL” result code. Numbers are added to the blacklist only if the modem connection fails. The %B command will list the numbers on the blacklists. 0 = disabled 1 = enabled 0 (disabled) 0–1 43 Dial Attempts to Blacklist. When blacklisting is enabled with S42, this value controls the number of dial attempts that will result in a number being blacklisted. 4 0–4 — 44 Blacklist Timer. Period during which blacklisting is active. 180 0–255 seconds 50 Minimum on-hook time—Modem will remain on-hook for S50 seconds. Any attempt to go off-hook will be delayed until this timer expires. 3 0–255 seconds 51 Number to start checking for an outside line on a PBX. See &X command for details. 1 0–9 — Rev. 1.0 Units 53 Si2494/39 6. User-Access Registers (U-Registers) U-Registers are 16-bit registers written by the AT:Uaa command and read by the AT:R (read all U-Registers) or AT:Raa (read U-Register aa) commands (see the AT command list in Table 13 on page 46). Many aspects of the modem’s and DAA’s behavior can be enabled/disabled, configured, monitored, and/or modified through URegisters; however, most of them will not be needed in normal use. There are two types of U-Registers. The first represents a single 16-bit term, such as a filter coefficient, threshold, delay, or other quantity. These registers can be read from or written to as a single 16-bit value. The second type of U-Register is bit-mapped. Bit-mapped registers are written and/or read in hexadecimal, but each bit or combination of bits in the register represents an independent value or status information. These individual bits are used to enable or disable features and indicate states. Some U-Registers are reserved and not available to the user. Therefore, there are gaps in the available U-Register address map. Additionally, some bits within available U-Registers are reserved. Any attempt to write a non-zero value to a reserved U-Register or bit may cause unpredictable modem operation. With over 100 U-Registers, the Si2494/39 offers an unprecedented level of programmability for a controller-based modem. A detailed list of these registers and their use is beyond the scope of this data sheet. Refer to “AN93: ISOmodem® Chipset Family Designer’s Guide” for details. 54 Rev. 1.0 Si2494/39 7. Pin Descriptions: Si2494/39 GPIO16, D2 GPIO17, D1 INT GPIO18, D0 CLKIN/XTALI N/C XTALO 38 37 36 35 34 33 32 GPIO1 1 31 GPIO25, D3 FSYNC 2 30 GPIO24, D4 CLKOUT 3 29 ESC, D5 N/C 4 28 DCD, D6 VDD 5 GND 6 VREG 7 SDI 8 SDO Si2494/39 27 N/C 26 VDD 25 GND 24 RTS, SS, D7 9 23 TXD, MOSI, WR EESDI 10 22 RXD, MISO, RD EESDO 11 21 CTS, SCLK, CS EECS 12 20 GPIO11, A0 5 x 7 mm QFN 13 14 15 16 17 18 19 RI C1A C2A RESET AOUTb AOUT EECLK Table 16. Si2494/39 Pin Descriptions Pin # Pin Name Description 1 GPIO1 General Purpose Input Output #1. 2 FSYNC Frame Sync/Data Bit. Frame Sync output to codec in serial mode. 3 CLKOUT 4 NC 5 VDD Digital Supply Voltage. Provides the 3.3V supply voltage to the Si2494/39. 6 GND Ground. Connects to the system digital ground. 7 VREG 8 SDI Serial Data In. Serial Data In (to codec) output in serial mode. 9 SDO Serial Data Out. Serial Data Output (from codec) input in serial mode. 10 EESDI EEPROM Serial Data Input. Serial Data In to SPI EEPROM. 11 EESDO EEPROM Serial Data Output. Serial Data Out from SPI EEPROM. Clock Output. Clock output in serial mode. No Connect. Regulator Voltage Reference. Connects to an external capacitor and serves as the reference for the internal voltage regulator. Rev. 1.0 55 Si2494/39 Table 16. Si2494/39 Pin Descriptions (Continued) Pin # Pin Name 12 EECS EEPROM Chip Select. Active low read/write enable for SPI EEPROM. 13 EECLK EEPROM Clock. Clock for SPI EEPROM. 14 AOUTb Audio Output B. PWM audio output B when differential audio output is enabled. 15 AOUT Audio Output. PWM audio output. 16 RESET Reset Input. An active low input that is used to reset all control registers to a defined initialized state. 17 C2A Isolation Capacitor 2A. Connects to one side of the isolation capacitor, C2. 18 C1A Isolation Capacitor 1A. Connects to one side of the isolation capacitor, C1. 19 RI 20 GPIO11, A0 21 56 Description Ring Indicator. The RI on (active low) indicates the presence of an ON segment of a ring signal on the telephone line. GPIO/Address Bit 0. General purpose input output pin 11. Address Enable in parallel mode. CTS, SCLKC, CS Clear to Send/Serial Data Clock/Chip Select. Signals that the Si2494/39 is ready to receive more digital data on the TXD pin in data mode. Serial data clock input in SPI mode. Active low chip select in parallel mode. 22 RXD/MISO/RD Receive Data/Master In Slave Out/Read Enable. Data output to DTE TXD pin in serial mode. Serial data output from modem in SPI mode. Active low read enable pin in parallel mode. 23 TXD/MOSI/WR Transmit Data/Master Out Slave In/Write Enable. Data input from DTE TXD pin in serial mode. Serial data input to modem in SPI mode. Active low write enable pin in parallel mode. 24 RTS, SS, D7 Request to Send/SPI Slave Select/Data Bit. Active low request to send input used for flow control in UART mode. Active low slave select in SPI mode. Bidirectional parallel bus data bit 7 in parallel mode. 25 GND Ground. Connects to the system digital ground. 26 VDD Digital Supply Voltage. Provides the 3.3V supply voltage to the Si2494/39, 27 NC No connect. Rev. 1.0 Si2494/39 Table 16. Si2494/39 Pin Descriptions (Continued) Pin # Pin Name Description 28 DCD, D6 Carrier Detect/Data Bit. Active low carrier detect in serial mode. Bidirectional parallel bus data bit 6 in parallel mode. 29 ESC, D5 Escape/Data Bit. Hardware escape in serial mode. Bidirectional parallel bus data bit 5 in parallel mode. 30 GPIO24, D4 General Purpose Input Output Bit/Data Bit. General purpose input output bit 24. Bidirectional parallel bus data bit 4 in parallel mode. 31 GPIO25, D3 General Purpose Input Output Bit/Data Bit. General purpose input output bit 25. Bidirectional parallel bus data bit 3 in parallel mode. 32 GPIO16, D2 General Purpose Input Output Bit/Data Bit. General purpose input output bit 16. Bidirectional parallel bus data bit 2 in parallel mode. 33 GPIO17, D1 General Purpose Input Output Bit/Data Bit. General purpose input output bit 17. Bidirectional parallel bus data bit 1 in parallel mode. 34 GPIO18, D0 General Purpose Input Output Bit/Data Bit. General purpose input output bit 18. Bidirectional parallel bus data bit 0 in parallel mode. 35 INT 36 CLKIN, XTAL1 37 XTALO 38 NC Interrupt Output. Active low interrupt output. Clock Input/Crystal Oscillator Pin. Provides support for parallel resonant AT cut crystals. A 4.9152 MHz or 32.768 crystal or a 32.768 kHz or 4.9152 or 27 MHz clock on XTAL1 is required. Crystal Oscillator Pin. Serves as the output of the crystal amplifier. No Connect. Rev. 1.0 57 Si2494/39 8. Pin Descriptions: Si3018 Si3018 QE DCT RX IB 1 2 3 4 C1B C2B VREG 5 RNG1 8 6 7 16 15 DCT2 14 DCT3 QB QE2 IGND 13 12 11 10 9 SC VREG2 RNG2 Table 17. Si3018 Pin Descriptions Pin # 1 Pin Name QE 2 DCT 3 RX 4 IB 5 C1B 6 C2B 7 VREG 8 RNG1 9 RNG2 10 VREG2 11 SC 12 QE2 13 QB 14 DCT3 15 IGND 16 DCT2 58 Description Transistor Emitter. Connects to the emitter of Q3. DC Termination. Provides dc termination to the telephone network. Receive Input. Serves as the receive side input from the telephone network. Internal Bias. Provides a bias voltage to the device. Isolation Capacitor 1B. Connects to one side of isolation capacitor C1 and communicates with the system side. Isolation Capacitor 2B. Connects to one side of isolation capacitor C2 and communicates with the system side. Voltage Regulator. Connects to an external capacitor to provide bypassing for an internal power supply. Ring 1. Connects through a resistor to the RING lead of the telephone line. Provides the ring and caller ID signals to the Si2494/39. Ring 2. Connects through a resistor to the TIP lead of the telephone line. Provides the ring and caller ID signals to the Si2494/39. Voltage Regulator 2. Connects to an external capacitor to provide bypassing for an internal power supply. SC Connection. Enables external transistor network. Should be tied through a 0  resistor to IGND. Transistor Emitter 2. Connects to the emitter of Q4. Transistor Base. Connects to the base of transistor Q4. DC Termination 3. Provides the dc termination to the telephone network. Isolated Ground. Connects to ground on the line-side interface. DC Termination 2. Provides dc termination to the telephone network. Rev. 1.0 Si2494/39 9. Ordering Guide Chipset Max Speed System-Side Package System-Side Line-Side Temp Range Si2494 56 kbps 38 QFN Si2494-A-FM Si3018-F-FS 0 to 70 °C Si2494 56 kbps 38 QFN Si2494-A-GM Si3018-F-GS –40 to 85 °C Si2439 33.6 kbps 38 QFN Si2439-A-FM Si3018-F-FS 0 to 70 °C Si2439 33.6 kbps 38 QFN Si2439-A-GM Si3018-F-GS –40 to 85 °C Note: Add an “R” at the end of the device to denote tape and reel option. Rev. 1.0 59 Si2494/39 10. Package Markings (Top Markings) 10.1. Si2494 Top Marking     Figure 9. Si2494-A-FM Top Marking     Figure 10. Si2494-A-GM Top Marking 10.2. Si2439 Top Marking     Figure 11. Si2439-A-FM Top Marking 60 Rev. 1.0 Si2494/39     Figure 12. Si2439-A-GM 10.3. Si2494/39 Top Markings Explanation Mark Method: Line 1 Marking: Line 2 Marking: Line 3 Marking: YAG Laser Part Number YY=Current Year WW=Work Week R = Die Revision T...T=Trace Code Circle=0.5 mm Diameter (Bottom-Left Justified) e3 Circle TW=Assembly Country Code Rev. 1.0 Assigned by the Assembly House. Corresponds to the last significant digit of the year and work week of the mold date. Pin 1 identifier. Pb-Free Symbol 61 Si2494/39 10.4. Si3018 Top Marking   Figure 13. Si3018-F-FS Top Marking     Figure 14. Si3018-F-GS Top Marking 10.5. Si3018 Top Markings Explanation Mark Method: Line 1 Marking: Line 2 Marking: YAG Laser Part Number YY=Current Year WW=Work Week R = Die Revision T...T=Trace Code Circle=0.5 mm Diameter (Bottom-Left Justified) e3 Circle 62 Rev. 1.0 Assigned by the Assembly House. Corresponds to the last significant digit of the year and work week of the mold date. Pin 1 identifier. Pb-Free Symbol Si2494/39 11. Package Outline: 38-Pin QFN Figure 15 illustrates the package details for the Si2494/39. Table 18 lists the values for the dimensions shown in the illustration. 2X bbb C B A ccc D C D2 A D/2 DETAIL "B" D2/2 A1 2X aaa C A 38 32 32 31 1 38 31 1 E/2 E2/2 E2 E e 20 12 13 20 19 12 19 13 38X L B 38X b ddd C A B C SEATING PLANE Detail A DETAIL "A" Detail B Pin-1 Identifier 38 (L) L1 38 1 1 (b) Option 1 Chamfered Corner Option 2 Corner Square Figure 15. 38-Pin Quad Flat No-Lead Package (QFN) Rev. 1.0 63 Si2494/39 Table 18. Package Diagram Dimensions1,2,3 Millimeters Symbol Min Nom Max A 0.75 0.85 0.95 A1 0.00 0.01 0.05 b 0.18 0.23 0.30 D D2 5.00 BSC. 3.10 e 3.20 3.30 0.50 BSC. E 7.00 BSC. E2 5.10 5.20 5.30 L 0.35 0.45 0.55 L1 0.03 0.05 0.08 aaa — — 0.10 bbb — — 0.10 ccc — — 0.08 ddd — — 0.10 Notes: 1. All dimensions shown are in millimeters (mm) unless otherwise noted. 2. Dimensioning and Tolerancing per ANSI Y14.5M-1982. 3. Recommended card reflow profile is per the JEDEC/IPC J-STD-020 specification for Small Body Components. 64 Rev. 1.0 Si2494/39 12. 38-Pin QFN Land Pattern Figure 16 shows the recommended land pattern for the Si2494/39 QFN-38 package. Table 19 lists the values for the dimensions shown in the illustration. Figure 16. QFN-38 Land Pattern Drawing Table 19. QFN-38 PCB Land Pattern Dimensions Dimension Feature Min Max C1 Pad column spacing 4.70 4.80 C2 Pad row spacing 6.70 6.80 E Pad pitch 0.50 BSC X1 Pin pad width 0.20 0.30 X2 Thermal pad width 3.20 3.30 Y1 Pin pad width 0.80 0.90 Y2 Thermal pad length 5.20 5.30 Notes: General 1. All dimensions shown are in millimeters (mm) unless otherwise noted. 2. This Land Pattern Design is based on the IPC-7351 guidelines. Solder Mask Design 1. All metal pads are to be non-solder mask defined (NSMD). Clearance between the solder mask and the metal pad is to be 60 m minimum, all the way around the pad. Stencil Design 1. A stainless steel, laser-cut and electro-polished stencil with trapezoidal walls should be used to assure good solder paste release. 2. The stencil thickness should be 0.125 mm (5 mils). 3. The ratio of stencil aperture to land pad size should be 1:1 for all perimeter pads 4. A 3x5 array of 0.90 mm square openings on 1.10 mm pitch should be used for the center ground pad. Card Assembly 1. A No-Clean, Type-3 solder paste is recommended. 2. The recommended card reflow profile is per the JEDEC/IPEC J-STD-020 specification for Small Body Components. Rev. 1.0 65 Si2494/39 13. Package Outline: 16-Pin SOIC Figure 17 illustrates the package details for the Si3018 16-pin packaging option. Table 20 lists the values for the dimensions shown in the illustration. Figure 17. 16-Pin Small Outline Integrated Circuit (SOIC) Package 66 Rev. 1.0 Si2494/39 Table 20. Package Diagram Dimensions Dimension Min Max A — 1.75 A1 0.10 0.25 A2 1.25 — b 0.31 0.51 c 0.17 0.25 D 9.90 BSC E 6.00 BSC E1 3.90 BSC e 1.27 BSC L 0.40 L2 1.27 0.25 BSC h 0.25 0.50 θ 0° 8° aaa 0.10 bbb 0.20 ccc 0.10 ddd 0.25 Notes: 1. All dimensions shown are in millimeters (mm) unless otherwise noted. 2. Dimensioning and Tolerancing per ANSI Y14.5M-1994. 3. This drawing conforms to the JEDEC Solid State Outline MS-012, Variation AC. 4. Recommended card reflow profile is per the JEDEC/IPC J-STD-020 specification for Small Body Components. Rev. 1.0 67 Si2494/39 14. 16-Pin SOIC Land Pattern Figure 18 illustrates the recommended land pattern for the Si2494/39 16-Pin SOIC. Table 21 lists the values for the dimensions shown in the illustration.   Figure 18. 16-Pin SOIC Land Pattern Diagram Table 21. 16-Pin SOIC Land Pattern Dimensions Dimension Feature (mm) C1 Pad Column Spacing 5.40 E Pad Row Pitch 1.27 X1 Pad Width 0.60 Y1 Pad Length 1.55 Notes: General 1. All dimensions shown are in millimeters (mm) unless otherwise noted. 2. Dimensioning and Tolerancing per ASME Y14.5M-1994. 3. This Land Pattern Design is based on the IPC-7351 guidelines. 4. All dimensions shown are at Maximum Material Condition (MMC). Least Material Condition (LMC) is calculated based on a Fabrication Allowance of 0.05 mm. Solder Mask Design 5. All metal pads are to be non-solder mask defined (NSMD). Clearance between the solder mask and the metal pad is to be 60 µm minimum, all the way around the pad. Stencil Design 6. A stainless steel, laser-cut and electro-polished stencil with trapezoidal walls should be used to assure good solder paste release. 7. The stencil thickness should be 0.125 mm (5 mils). 8. The ratio of stencil aperture to land pad size should be 1:1. Card Assembly 9. A No-Clean, Type-3 solder paste is recommended. 10. The recommended card reflow profile is per the JEDEC/IPC J-STD-020 specification for Small Body Components. 68 Rev. 1.0 Si2494/39 NOTES: Rev. 1.0 69 Smart. Connected. Energy-Friendly. Products Quality Support and Community www.silabs.com/products www.silabs.com/quality community.silabs.com Disclaimer Silicon Labs intends to provide customers with the latest, accurate, and in-depth documentation of all peripherals and modules available for system and software implementers using or intending to use the Silicon Labs products. Characterization data, available modules and peripherals, memory sizes and memory addresses refer to each specific device, and "Typical" parameters provided can and do vary in different applications. Application examples described herein are for illustrative purposes only. Silicon Labs reserves the right to make changes without further notice to the product information, specifications, and descriptions herein, and does not give warranties as to the accuracy or completeness of the included information. Without prior notification, Silicon Labs may update product firmware during the manufacturing process for security or reliability reasons. Such changes will not alter the specifications or the performance of the product. Silicon Labs shall have no liability for the consequences of use of the information supplied in this document. This document does not imply or expressly grant any license to design or fabricate any integrated circuits. The products are not designed or authorized to be used within any FDA Class III devices, applications for which FDA premarket approval is required or Life Support Systems without the specific written consent of Silicon Labs. A "Life Support System" is any product or system intended to support or sustain life and/or health, which, if it fails, can be reasonably expected to result in significant personal injury or death. Silicon Labs products are not designed or authorized for military applications. Silicon Labs products shall under no circumstances be used in weapons of mass destruction including (but not limited to) nuclear, biological or chemical weapons, or missiles capable of delivering such weapons. Silicon Labs disclaims all express and implied warranties and shall not be responsible or liable for any injuries or damages related to use of a Silicon Labs product in such unauthorized applications. Trademark Information Silicon Laboratories Inc.® , Silicon Laboratories®, Silicon Labs®, SiLabs® and the Silicon Labs logo®, Bluegiga®, Bluegiga Logo®, ClockBuilder®, CMEMS®, DSPLL®, EFM®, EFM32®, EFR, Ember®, Energy Micro, Energy Micro logo and combinations thereof, "the world’s most energy friendly microcontrollers", Ember®, EZLink®, EZRadio®, EZRadioPRO®, Gecko®, Gecko OS, Gecko OS Studio, ISOmodem®, Precision32®, ProSLIC®, Simplicity Studio®, SiPHY®, Telegesis, the Telegesis Logo®, USBXpress® , Zentri, the Zentri logo and Zentri DMS, Z-Wave®, and others are trademarks or registered trademarks of Silicon Labs. ARM, CORTEX, Cortex-M3 and THUMB are trademarks or registered trademarks of ARM Holdings. Keil is a registered trademark of ARM Limited. Wi-Fi is a registered trademark of the Wi-Fi Alliance. All other products or brand names mentioned herein are trademarks of their respective holders. Silicon Laboratories Inc. 400 West Cesar Chavez Austin, TX 78701 USA http://www.silabs.com