SI4311-B10-GMR

S i 4 3 11 315/433.92 MH Z FSK R ECEIVER Features   Applications     Satellite set-top box receivers Remote controls, IR replacement/extension  Garage and gate door openers  Home automation and security Ordering Information: See page 14. Remote keyless entry After market alarms  Telemetry  Wireless point of sale  Toys Pin Assignments Si4311 (Top View) Description Si4311 Antenna LNA PGA ADC AGC 2.7 – 3.6 V VDD GND LDO AFC XTAL OSC 20 19 18 17 16 RFGND 2 15 BT0 RX_IN 3 14 BT1 GND PAD RST 4 13 DOUT 6 7 8 9 10 XTL1 XTL2 12 GND VDD AFC 5 11 VDD Patents pending DOUT ADC RX_IN 1 GND Functional Block Diagram VDD 315/434 The Si4311 is a fully-integrated FSK CMOS RF receiver that operates in the unlicensed 315 and 433.92 MHz ultra high frequency (UHF) bands. It is designed for high-volume, cost-sensitive RF receiver applications, such as set-top box RF receivers, remote controls, garage door openers, home automation, security, remote keyless entry systems, wireless POS, and telemetry. The Si4311 offers industry-leading RF performance, high integration, flexibility, low BOM, small board area, and ease of design. No production alignment is necessary as all RF functions are integrated into the device. DEV1  DEV0  NC  Data rates up to 10 kbps Direct battery operation with onchip low drop out (LDO) voltage regulator 16 MHz crystal oscillator support 3x3x0.85 mm 20L QFN package (RoHS compliant) –40 to +85 °C temperature range NC  Single chip receiver with only six  external components  Selectable 315/433.92 MHz carrier frequency Supports FSK modulation  High sensitivity (–104 dBm @ 5 kbps)  Excellent interference rejection  Selectable IF bandwidths Automatic Frequency Centering (AFC) NC  DSP MCU BASEBAND PROCESSOR SQUELCH AFC 315/434 DEV[1:0] BT[1:0] RST 16 MHz Rev. 0.5 3/10 Copyright © 2010 by Silicon Laboratories Si4311 This information applies to a product under development. Its characteristics and specifications are subject to change without notice. Si4 311 2 Rev. 0.5 Si4311 TABLE O F C ONTENTS Section Page 1. Electrical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 2. Typical Application Schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 2.1. Typical Application Bill of Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 3. Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 3.1. Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 3.2. Receiver Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 3.3. Carrier Frequency Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 3.4. Bit Time BT[1:0] Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 3.5. Frequency Deviation Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 3.6. Automatic Frequency Centering (AFC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11 3.7. Low Noise Amplifier Input Circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 3.8. Crystal Oscillator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 3.9. Reset Pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 4. Pin Descriptions: Si4311-B10-GM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 5. Ordering Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 6. Package Markings (Top Marks) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 6.1. Si4311 Top Mark . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 6.2. Top Mark Explanation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 7. Package Outline: Si4311-B10-GM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 8. PCB Land Pattern: Si4311-B10-GM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Document Change List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19 Contact Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20 Rev. 0.5 3 Si4 311 1. Electrical Specifications Table 1. Recommended Operating Conditions* Parameter Symbol Min Typ Max Unit VDD 2.7 3.3 3.6 V VDD-RISE 10 — — μs TA –40 25 85 °C Supply Voltage Supply Voltage Powerup Rise Time Ambient Temperature Test Condition *Note: All minimum and maximum specifications are guaranteed and apply across the recommended operating conditions. Typical values apply at VDD = 3.3 V and 25 C unless otherwise stated. Parameters are tested in production unless otherwise stated. Table 2. Absolute Maximum Ratings1,2 Parameter Symbol Value Unit Supply Voltage VDD –0.5 to 3.9 V Input Current3 IIN 10 mA Input Voltage3 VIN –0.3 to (VDD + 0.3) V Operating Temperature TOP –45 to 95 C Storage Temperature TSTG –55 to 150 C 0.4 VPK RF Input Level4 Notes: 1. Permanent device damage may occur if the absolute maximum ratings are exceeded. Functional operation should be restricted to the conditions as specified in the operational sections of this data sheet. Exposure beyond recommended operating conditions for extended periods may affect device reliability. 2. The Si4311 device is a high-performance RF integrated circuit with certain pins having an ESD rating of < 2 kV HBM. Handling and assembly of this device should only be done at ESD-protected workstations. 3. For input pins 315/434, AFC, BT[1:0], and DEV[1:0]. 4. At RF input pin RX_IN. 4 Rev. 0.5 Si4311 Table 3. DC Characteristics (TA = 25 °C, VDD = 3.3 V, Rs = 50 Ω, FRF = 433.92 MHz unless otherwise noted) Parameter Symbol Supply Current Test Condition IVDD Reset Supply Current IRST Reset asserted Min Typ Max Unit — 20 — mA — 2 TBD µA 1 VIH 0.7 x VDD — VDD + 0.3 V Low Level Input Voltage1 VIL –0.3 — 0.3 x VDD V 1 IIH VIN = VDD = 3.6 V –10 — 10 µA High Level Input Voltage High Level Input Current Low Level Input Current1 IIL VIN = 0 V, VDD = 3.6 V –10 — 10 µA 2 VOH IOUT = 500 µA 0.8 x VDD — — V Low Level Output Voltage2 VOL IOUT = –500 µA — — 0.2 x VDD V High Level Output Voltage Notes: 1. For input pins 315/434, AFC, BT[1:0], and DEV[1:0]. 2. For output pin DOUT. Table 4. Reset Timing Characteristics (VDD = 3.3 V, TA = 25 °C) Parameter Symbol Min Typ Max Unit tSRST 100 — — µs RST Pulse Width tSRST RST 70% 30% Figure 1. Reset Timing Rev. 0.5 5 Si4 311 Table 5. Si4311 Receiver Characteristics (TA = 25 °C, VDD = 3.3 V, Rs = 50 Ω, FRF = 433.92 MHz unless otherwise noted) Parameter Test Condition Min Typ Max Unit 1.0 kbps, f = 50 kHz, xtal = ±20 ppm, 315 MHz (Note 2) — –104 — dBm 10 kbps, f = 50 kHz, xtal = ±20 ppm, 315 MHz (Note 2) — –101 — dBm 1.0 kbps, f = 50 kHz, xtal = ±20 ppm, 433.92 MHz (Note 2) — –102 — dBm 10 kbps, f = 50 kHz, xtal = ±20 ppm, 433.92 MHz TBD –100 — dBm — — 10 kbps Adjacent Channel Rejection ±200 kHz1 Desired signal is 3 dB above sensitivity (BER = 10–3), unmodulated interferer is at ±200 kHz, rejection measured as TBD difference between desired signal and interferer level in dB when BER = 10–3 35 — dB Alternate Channel Rejection ±400 kHz1,2 Desired signal is 3 dB above sensitivity (BER = 10–3), unmodulated interferer is at ±400 kHz, rejection measured as difference between desired signal and interferer level in dB when BER = 10–3 — 55 — dB — 35 — dB ±2 MHz, 2.4 kbps, desired signal is 3 dB above sensitivity, CW interferer level is increased until BER = 10–3 — 65 — dB ±10 MHz, 2.4 kbps, desired signal is 3 dB above sensitivity, CW interferer level is increased until BER = 10–3 — 70 — dB — 8 — dBm — –10 — dBm 10 — 90 kHz — 7 — pF — 320 — ms Sensitivity @ BER = Symbol 10-3 (Note 1) Data Rate3 Image Rejection, IF = 128 kHz1,2 Blocking1,2 Maximum RF Input Power 1,2 | f2 – f1 | = 5 MHz, high gain mode, desired signal is 3 dB above sensitivity, CW interference levels are increased until BER = 10–3 Input IP33 FSK Deviation Input Range3 LNA Input Capacitance RX Boot Time3 3 From reset Notes: 1. 1.0 kbps, f = 50 kHz, xtal = ±20 ppm, AFC = 0, BT[1:0] = 00, DEV[1:0] = 01. 2. Guaranteed by characterization. 3. Guaranteed by design. 6 Rev. 0.5 Si4311 Table 6. Crystal Characteristics (VDD = 3.3 V, TA = 25 °C) Parameter Symbol Test Condition Min Typ Max Unit Crystal Oscillator Frequency — 16 — MHz Crystal ESR — — 100  XTL1, XTL2 Input Capacitance — 11 — pF Rev. 0.5 7 Si4 311 2. Typical Application Schematic DEV0 20 19 18 17 16 L1 C3 1 VDD 2 RFGND 3 U1 RX_IN Si4311-GM 4 RST 5 AFC GND PAD BT0 BT1 BT0 BT1 DOUT GND 15 14 13 12 VDD 11 DOUT VDD C1 22 nF VBATTERY 2.7 to 3.6 V 6 7 8 9 10 C2 1 uF NC NC NC DEV0 DEV1 VDD 434 GND VDD XTL1 XTL2 RX ANTENNA R1 20 k DEV1 AFC X1 (16 MHz) Figure 2. Si4311 FSK 433.92 MHz Application Schematic 2.1. Typical Application Bill of Materials Table 7. Si4311 Typical Application Bill of Materials 8 Component(s) Value/Description Supplier(s) C1 Supply bypass capacitor, 22 nF, 20%, Z5U/X7R Murata C2 Time constant capacitor, 1 µF Murata C3 Antenna matching capacitor, 15 pF Murata L1 Antenna matching inductor, 33 nH for 433.92 MHz and 62 nH for 315 MHz Murata R1 Time constant resistor, 20 k Murata X1 16 MHz crystal Hosonic U1 Si4311 315/433.92 MHz FSK receiver Silicon Laboratories Rev. 0.5 Si4311 3. Functional Description 3.1. Overview Si4311 Antenna LNA PGA ADC AGC 2.7 – 3.6 V VDD GND DOUT ADC RX_IN LDO AFC DSP MCU BASEBAND PROCESSOR SQUELCH XTAL OSC AFC 315/434 DEV[1:0] BT[1:0] RST 16 MHz Figure 3. Functional Block Diagram The Si4311 is a fully-integrated FSK CMOS RF receiver that operates in the unlicensed 315 and 433.92 MHz ultra high frequency (UHF) bands. It is designed for high-volume, cost-sensitive RF receiver applications. The chip operates at a carrier frequency of 315 or 433.92 MHz and supports FSK digital modulation with data rates of up to 10 kbps. The device leverages Silicon Labs’ patented and proven digital low-IF architecture and offers superior sensitivity and interference rejection. The Si4311 can achieve superior sensitivity in the presence of large interference due to its high dynamic range ADCs and digital filters. The digital low-IF architecture also enables superior blocking ability and low intermodulation distortion for robust reception in the presence of wide-band interference. Digital integration reduces the number of required external components compared to traditional offerings, resulting in a solution that only requires a 16 MHz crystal and passive components allowing a small and compact printed circuit board (PCB) implementation area. The high integration of the Si4311 improves the system manufacturing reliability, improves quality, eases design-in, and minimizes costs. 3.2. Receiver Description The RF input signal is amplified by a low-noise amplifier (LNA) and down-converts to a low intermediate frequency with a quadrature image-reject mixer. The mixer output is amplified by a programmable gain amplifier (PGA), filtered, and digitized with a highresolution analog-to-digital converter (ADC). All RF functions are integrated into the device eliminating any production alignment issues associated with external components, such as SAW and ceramic IF filters. Silicon Labs’ advanced digital low-IF architecture achieves superior performance by using the DSP to perform channel filtering, demodulation, automatic gain control (AGC), automatic frequency control (AFC), and other baseband processing. DSP implementation of the channel filters provides better repeatability and control of the bandwidth and frequency response of the filter compared to analog implementations. No off-chip ceramic filters are needed with the Si4311 since all IF channel filtering is performed in the digital domain. 3.3. Carrier Frequency Selection The Si4311 can be tuned to either 315 or 433.92 MHz by driving Pin 6 (315/434) to VDD or GND. The 315 MHz operation is chosen by driving Pin 6 (315/434) to VDD, and 433.92 MHz operation is chosen by driving Pin 6 (315/434) to GND. Rev. 0.5 9 Si4 311 Table 8. Carrier Frequency Selection Pin 6 (315/434) Frequency [MHz] 0 433.92 1 315 3.4. Bit Time BT[1:0] Selection The Si4311 can operate with data rates of up to 10 kbps non-return to zero (NRZ) data or 5 kbps Manchester encoded data. However, FSK modulation uses other encoding schemes, such as pulse width modulation (PWM) and pulse position modulation (PPM) in which a bit can be encoded into a pulse with a certain duty cycle or pulse width (see Figure 4). Digital Data “1” “0” “1” “1” NRZ Encoding Manchester Encoding PPM Encoding 100 us 1000 us Figure 4. Example Data Waveforms In order to set the data filter bandwidth correctly, the shortest pulse width of the transmitted encoded data should be chosen as the bit time. In the PPM example shown in Figure 4, the shortest pulse width is 100 µs, so the bit time is chosen as BT = 100 µs even though the actual data rate is 1 kbps (1000 µs). After finding BT, Table 9 can be used to find the bit settings for pins 14 and 15, BT[1:0]. In this PPM example, BT[1:0] is set as logic BT1 = 1 and BT0 = 1 or BT[1:0] = (1,1) since BT = 100 µs. Table 9. How to Choose BT[1:0] Based on the Bit Time 10 Bit Time [us] BT1 (pin 14) BT0 (pin 15) BT ≥ 1000 0 0 1000< BT ≤ 500 0 1 500 < BT ≤ 200 1 0 200 < BT ≤ 100 1 1 Rev. 0.5 Si4311 3.5. Frequency Deviation Selection In order to accommodate wide frequency deviation ranges, the Si4311 FSK receiver uses two input pins, pins 16 and 17, to select a range of frequency deviations as shown in Table 10. For example, if the FSK signal has a frequency deviation (F) of 50 kHz, then the DEV[1:0] = (0,1) or pin 16 = 0 and pin 17 = 1. Table 10. Frequency Deviation Range Settings DEV1 (pin 16) DEV0 (pin 17) Frequency Deviation [kHz] 0 0 1 < ∆F ≤ 30 0 1 30 < ∆F ≤ 50 1 0 50 < ∆F ≤ 70 1 1 70 < ∆F ≤ 90 3.6. Automatic Frequency Centering (AFC) The channel bandwidth directly affects the sensitivity of any wireless receiver. Typical analog FSK receivers use an external ceramic filter with a large bandwidth to accommodate the data rate, frequency deviation, crystal tolerances, and transmit carrier frequency offsets, which leads to unnecessary amounts of noise and lower sensitivity levels. The Si4311 uses a narrow channel bandwidth of 200 kHz and automatic frequency centering (AFC) to obtain excellent sensitivity levels (–104 dBm at data rate of 5 kbps at 315 MHz) while still accommodating up to ±200 kHz of frequency tracking from its center frequency. IF BW 200kHz (a) TX OFFSET 100kHz (b) TX OFFSET 100kHz (c) Figure 5. (a) Ideal case (b) Scenario with Tx Offset (c) Si4311 AFC Re-Centers IF BW In the ideal case of no transmit carrier frequency errors or receiver frequency errors, both FSK tones for a logic "1" and "0" from the transmitter appear in the receiver IF channel bandwidth as shown in Figure 5 (a). However, if the transmitter has a large carrier offset such as shown in Figure 5 (b), then only one of the FSK tones falls in the receiver channel bandwidth and thus the receiver produces errors. The standard approach to resolving this problem is to use an IF channel filter that is large enough to accommodate the transmitter frequency error, but this leads to degraded sensitivity. The Si4311 uses AFC to re-center the channel bandwidth about the two FSK tones as shown in Figure 5 (c) to maintain excellent sensitivity with a small IF channel filter. The algorithm requires one FSK tone to be in-band and at most three alternating sequences of 0/1 data typically found in a preamble plus 700 µs of fixed delay time (approximately 230 µs per 0/1 data pair) to re-center the IF bandwidth. Worst case acquisition time is 1.3 ms for a data rate of 10 kbps. The AFC algorithm includes a 200 ms hold time. The device holds the frequency found by the AFC algorithm for a time of 200 ms after no RF signal activity before restarting the frequency search. This allows a frequency found in the first packet of transmission to be held for any subsequent retransmissions of packets if the retransmissions occur before 200 ms. This hold frequency ensures all bits of the second and subsequent packets are recovered completely. The AFC frequency search resumes after 200 ms of no RF signal activity. The AFC algorithm can be disabled by setting the logic level on pin 5 to a logic zero as shown in Table 11. Rev. 0.5 11 Si4 311 Table 11. AFC Selection Pin 5 Pin 5 AFC 0 Disable 1 Enable 3.7. Low Noise Amplifier Input Circuit Figure 2 shows the typical application circuit with 50  matching. Components C3 and L1 are used to transform the input impedance of the LNA. C3 is equal to 15 pF and L1 is equal to 33 nH at 433.92 MHz and 62 nH at 315 MHz for 50  matching. 3.8. Crystal Oscillator An on-board crystal oscillator is used to generate a 16 MHz reference clock for the Si4311. This reference frequency is required for proper operation of the Si4311 and is used for calibration of the on-chip VCO and other timing references. No external load capacitors are required to set the 16 MHz reference frequency if the recommended crystal load capacitor is around 14 pF, assuming the effective board capacitance between pins XTL1 and XTL2 is 3 pF and the chip input capacitance on pins XTL1 or XTL2 is 11 pF. Refer to Table 6, “Crystal Characteristics,” on page 7 for board capacitance and frequency tolerance information. The frequency tolerance of the crystal should be chosen such that the received signal is within the IF bandwidth of the Si4311 receiver. Additionally, the Si4311 can be driven by an external 16 MHz reference clock. The clock signal can be applied to either the XTL1 or XTL2 inputs. When the 16 MHz reference clock is applied to one of the inputs, the other crystal input pin must be floating. 3.9. Reset Pin Driving the RST pin (pin 4) low will disable the Si4311 and place the device into reset mode. All active blocks in the device are powered off in this mode, bringing the current consumption to