SI4720-B20-GM

Si4720/21-B20 B R O A D C A S T FM R A DI O T R A N S C E I V E R F OR P O RTAB L E A P P L I C AT I O N S Features Advanced modulation control  Audio dynamic range control  Audio silence detector  Programmable reference clock input  2-wire and 3-wire control interface  2.7 to 5.5 V supply voltage  3 x 3 x 0.55 mm 20-pin Pb-free QFN package  RDS/RDBS encoder/decoder (Si4721 only) Pin Assignments   Cellular handsets/hands-free  MP3 players  Portable media players Wireless speakers/microphone  Satellite digital audio radios  Personal computers/notebooks Description The Si4720/21 integrates the complete tuner and transmit functions for FM broadcast reception and standards-compliant, unlicensed FM broadcast stereo transmission. Users must comply with local radio frequency (RF) transmission regulations. Functional Block Diagram Si4720/21 Tx/Rx Ant TXO LIN/DFS L1 120 nH RIN/DOUT ADC ADC AGC DAC LOUT/DFS 19 18 17 16 FMI 2 15 RIN/DOUT RFGND 3 GND PAD 14 LOUT/DFS RST 5 12 GND 6 7 8 9 10 11 VDD TXO 4 13 ROUT/DIN Patents pending Notes: 1. To ensure proper operation and FM transceiver performance, follow the guidelines in “AN383: 3 mm x 3 mm QFN Universal Layout Guide.” Skyworks will evaluate schematics and layouts for qualified customers. 2. Place the Si4720/21 as close as possible to the antenna jack, and keep the FMI trace as short as possible. SEN CONTROL INTERFACE GPO3/DCLK GPO GPO1 *Note: Dedicated Rx antenna is optional AFC GPO2/INT LDO RCLK VDD GND C1 22 uF ROUT/DIN 20 VIO RFGND DAC DSP RST PGA SDIO LNA SCLK FMI MUX Rx Ant* 1 LIN/DFS Si4720/21 (Top View) NC Applications 2.7–5.5 V Ordering Information: See page 41. GPO3/DCLK Minimal BOM (15 mm2)  Digital audio output (Si4721 only)  Digital audio input   VIO  Adjustable soft mute GPO2/INT   RCLK  Adjustable mono/stereo blend GPO1   SDIO  Adjustable seek parameters NC   SCLK  Full FM RX and TX in 3 x 3 QFN Worldwide FM RX band support Compliant with worldwide FM TX regulations Excellent real-world performance Supports integrated TX/RX antenna Programmable transmit output voltage Frequency synthesizer with integrated VCO Integrated LDO regulator SEN  Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com Rev. 1.0 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • November 9, 2021 Si4720/21-B20 TABLE O F C ONTENTS Section Page 1. Electrical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 2. Test Circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 2.1. Test Circuit Schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 2.2. Test Circuit Bill of Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 3. Typical Application Schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 3.1. Analog Audio Inputs/Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 3.2. Typical Application Bill of Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 3.3. Digital Audio Inputs/Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 3.4. Typical Application Schematic Bill of Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 4. Universal AM/FM RX/FM TX Application Schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . .21 4.1. Universal AM/FM RX/FM TX Bill of Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 5. Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 5.1. Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 5.2. Application Schematics and Operating Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 5.3. FM Receiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24 5.4. Integrated Antenna Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 5.5. Receiver Digital Audio Interface (Si4721 Only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 5.6. Stereo Audio Processing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 5.7. De-Emphasis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 5.8. Stereo DAC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27 5.9. Soft Mute . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 5.10. RDS/RBDS Processor (Si4721 Only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27 5.11. Tuning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 5.12. Seek . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 5.13. Reference Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 5.14. FM Transmitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28 5.15. Receive Power Scan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 5.16. Transmitter Digital Audio Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 5.17. Line Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 5.18. Audio Dynamic Range Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 5.19. Audio Limiter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32 5.20. Pre-emphasis and De-emphasis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 5.21. RDS/RBDS Processor (Si4721 Only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32 5.22. Tuning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 5.23. Reference Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 5.24. Control Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 5.25. GPO Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 5.26. Reset, Powerup, and Powerdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 5.27. Programming with Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 6. Commands and Properties . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 7. Pin Descriptions: Si4720/21-GM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 2 Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com Rev. 1.0 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • November 9, 2021 Si4720/21-B20 8. Ordering Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 9. Package Markings (Top Marks) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 9.1. Top Mark Explanation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 9.2. Si4720/21 Top Mark . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 9.3. Si4721 Top Mark . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 10. Package Outline: Si4720/21-GM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 11. PCB Land Pattern: Si4720/21-GM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44 12. Additional Reference Resources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 Contact Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47 Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 3 Rev. 1.0 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • November 9, 2021 Si4720/21-B20 1. Electrical Specifications Table 1. Recommended Operating Conditions Parameter Symbol Test Condition Min Typ Max Unit Supply Voltage VDD 2.7 — 5.5 V Interface Supply Voltage VIO 1.5 — 3.6 V Power Supply Power-Up Rise Time VDDRISE 10 — — µs Interface Power Supply Power-Up Rise Time VIORISE 10 — — µs TA –20 25 85 C Ambient Temperature Note: All minimum and maximum specifications are guaranteed and apply across the recommended operating conditions. Typical values apply at VDD = 3.3 V and 25 C unless otherwise stated. Parameters are tested in production unless otherwise stated. Table 2. Absolute Maximum Ratings1,2 Parameter Symbol Value Unit Supply Voltage VDD –0.5 to 5.8 V Interface Supply Voltage VIO –0.5 to 3.9 V 3 Input Current IIN 10 mA Input Voltage3 VIN –0.3 to (VIO + 0.3) V Operating Temperature TOP –40 to 95 C Storage Temperature TSTG –55 to 150 C 0.4 VPK RF Input Level4 Notes: 1. Permanent device damage may occur if the absolute maximum ratings are exceeded. Functional operation should be restricted to the conditions as specified in the operational sections of this data sheet. Exposure beyond recommended operating conditions for extended periods may affect device reliability. 2. The Si4720/21 devices are high-performance RF integrated circuits with certain pins having an ESD rating of < 2 kV HBM. Handling and assembly of these devices should only be done at ESD-protected workstations. 3. For input pins SCLK, SEN, SDIO, RST, RCLK, GPO1, GPO2/INT, and GPO3. 4. At RF input pin FMI. 4 Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com Rev. 1.0 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • November 9, 2021 Si4720/21-B20 Table 3. DC Characteristics Parameter Symbol Test Condition Min Typ Max Unit — 19.2 22 mA — 19.8 23 mA — 320 600 µA FM Receiver RX Supply Current IRX RX Supply Current1 IRX RX Interface Supply Current RX RDS Supply Current 2 RX Supply Current2 Low SNR level IIORX IFM Analog Output Mode — 19.9 23 mA IFMD Digital Output Mode — 18.0 20.5 mA ITX — 18.8 22.8 mA IIOTX — 320 600 µA FM Transmitter TX Supply Current TX Interface Supply Current FM Transmitter from Digital Audio Input TX Supply Current IDTX DCLK = 3.072 MHz — 18.3 — mA TX Interface Supply Current IDIO DCLK = 3.072 MHz — 320 — µA IRX — 16.8 — mA IIORPS — 400 — µA FM Transmitter in Receive Power Scan Mode RX Supply Current RX Interface Supply Current Supplies and Interface VDD Powerdown Current IDDPD Powerdown mode — 10 20 µA VIO Powerdown Current IIOPD SCLK, RCLK inactive Powerdown mode — 3 10 µA High Level Input Voltage3 VIH 0.7 x VIO — VIO + 0.3 V Low Level Input Voltage3 VIL –0.3 — 0.3 x VIO V High Level Input Current3 IIH VIN = VIO = 3.6 V –10 — 10 µA Low Level Input Current3 IIL VIN = 0 V, VIO = 3.6 V –10 — 10 µA 4 High Level Output Voltage VOH IOUT = 500 µA 0.8 x VIO — — V Low Level Output Voltage4 VOL IOUT = –500 µA — — 0.2 x VIO V Notes: 1. LNA is automatically switched to higher current mode for optimum sensitivity in weak signal conditions. 2. Guaranteed by characterization. 3. For input pins SCLK, SEN, SDIO, RST, RCLK, GPO1, GPO2/INT, and GPO3. 4. For output pins SDIO, GPO1, GPO2/INT, and GPO3. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 5 Rev. 1.0 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • November 9, 2021 Si4720/21-B20 Table 4. Reset Timing Characteristics1,2,3 (VDD = 2.7 to 5.5 V, VIO = 1.5 to 3.6 V, TA = –20 to 85 °C) Parameter Symbol Min Typ Max Unit RST Pulse Width and GPO1, GPO2/INT Setup to RST tSRST 100 — — µs GPO1, GPO2/INT Hold from RST tHRST 30 — — ns Important Notes: 1. When selecting 2-wire mode, the user must ensure that a 2-wire start condition (falling edge of SDIO while SCLK is high) does not occur within 300 ns before the rising edge of RST. 2. When selecting 2-wire mode, the user must ensure that SCLK is high during the rising edge of RST, and stays high until after the 1st start condition. 3. When selecting 3-wire or SPI modes, the user must ensure that a rising edge of SCLK does not occur within 300 ns before the rising edge of RST. 4. If GPO1 and GPO2 are actively driven by the user, then minimum tSRST is only 30 ns. If GPO1 or GPO2 is hi-Z, then minimum tSRST is 100 µs, to provide time for on-chip 1 M devices (active while RST is low) to pull GPO1 high and GPO2 low. tSRST RST 70% GPO1 70% GPO2/ INT tHRST 30% 30% 70% 30% Figure 1. Reset Timing Parameters for Busmode Select 6 Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com Rev. 1.0 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • November 9, 2021 Si4720/21-B20 Table 5. 2-Wire Control Interface Characteristics1,2,3 (VDD = 2.7 to 5.5 V, VIO = 1.5 to 3.6 V, TA = –20 to 85 °C) Parameter Symbol Test Condition Min Typ Max Unit SCLK Frequency fSCL 0 — 400 kHz SCLK Low Time tLOW 1.3 — — µs SCLK High Time tHIGH 0.6 — — µs SCLK Input to SDIO Setup (START) tSU:STA 0.6 — — µs SCLK Input to SDIO Hold (START) tHD:STA 0.6 — — µs SDIO Input to SCLK Setup tSU:DAT 100 — — ns SDIO Input to SCLK Hold tHD:DAT 0 — 900 ns tSU:STO 0.6 — — µs STOP to START Time tBUF 1.3 — — µs SDIO Output Fall Time tf:OUT — 250 ns — 300 ns 4,5 SCLK input to SDIO Setup (STOP) Cb 20 + 0.1 -----------1 pF SDIO Input, SCLK Rise/Fall Time tf:IN tr:IN SCLK, SDIO Capacitive Loading Cb — — 50 pF Input Filter Pulse Suppression tSP — — 50 ns Cb 20 + 0.1 -----------1 pF Notes: 1. When VIO = 0 V, SCLK and SDIO are low-impedance. 2-wire control interface is I2C compatible. 2. When selecting 2-wire mode, the user must ensure that a 2-wire start condition (falling edge of SDIO while SCLK is high) does not occur within 300 ns before the rising edge of RST. 3. When selecting 2-wire mode, the user must ensure that SCLK is high during the rising edge of RST, and stays high until after the first start condition. 4. The Si4720/21 delays SDIO by a minimum of 300 ns from the VIH threshold of SCLK to comply with the minimum tHD:DAT specification. 5. The maximum tHD:DAT has only to be met when fSCL = 400 kHz. At frequencies below 400 KHz, tHD:DAT may be violated as long as all other timing parameters are met. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 7 Rev. 1.0 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • November 9, 2021 Si4720/21-B20 SCLK 70% SDIO 70% tSU:STA tHD:STA tLOW START tr:IN tHIGH tr:IN tf:IN tSP tSU:STO tBUF 30% 30% tf:IN, tf:OUT tHD:DAT tSU:DAT STOP START Figure 2. 2-Wire Control Interface Read and Write Timing Parameters SCLK A6-A0, R/W SDIO START ADDRESS + R/W D7-D0 ACK DATA D7-D0 ACK DATA ACK STOP Figure 3. 2-Wire Control Interface Read and Write Timing Diagram 8 Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com Rev. 1.0 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • November 9, 2021 Si4720/21-B20 Table 6. 3-Wire Control Interface Characteristics (VDD = 2.7 to 5.5 V, VIO = 1.5 to 3.6 V, TA = –20 to 85 °C) Parameter Symbol Test Condition Min Typ Max Unit SCLK Frequency fCLK 0 — 2.5 MHz SCLK High Time tHIGH 25 — — ns SCLK Low Time tLOW 25 — — ns tS 20 — — ns SDIO Input to SCLKHold tHSDIO 10 — — ns SEN Input to SCLKHold tHSEN 10 — — ns SCLKto SDIO Output Valid tCDV Read 2 — 25 ns SCLKto SDIO Output High Z tCDZ Read 2 — 25 ns SCLK, SEN, SDIO, Rise/Fall time tR, tF — — 10 ns SDIO Input, SEN to SCLKSetup Note: When selecting 3-wire mode, the user must ensure that a rising edge of SCLK does not occur within 300 ns before the rising edge of RST. SCLK 70% 30% tR tF tHSDIO tS SEN 70% SDIO 70% tHIGH tLOW tHSEN tS 30% A7 30% A6-A5, R/W, A4-A1 A0 D15 D14-D1 Address In D0 Data In Figure 4. 3-Wire Control Interface Write Timing Parameters SCLK 70% SEN 70% 30% t HSDIO tS tCDV tHSEN t CDZ tS 30% 70% SDIO A7 30% A6-A5, R/W, A4-A1 Address In A0 D15 ½ Cycle Bus Turnaround D14-D1 D0 Data Out Figure 5. 3-Wire Control Interface Read Timing Parameters Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 9 Rev. 1.0 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • November 9, 2021 Si4720/21-B20 Table 7. SPI Control Interface Characteristics (VDD = 2.7 to 5.5 V, VIO = 1.5 to 3.6 V, TA = –20 to 85 °C) Parameter Symbol Test Condition Min Typ Max Unit SCLK Frequency fCLK 0 — 2.5 MHz SCLK High Time tHIGH 25 — — ns SCLK Low Time tLOW 25 — — ns tS 15 — — ns SDIO Input to SCLKHold tHSDIO 10 — — ns SEN Input to SCLKHold tHSEN 5 — — ns SCLKto SDIO Output Valid tCDV Read 2 — 25 ns SCLKto SDIO Output High Z tCDZ Read 2 — 25 ns SCLK, SEN, SDIO, Rise/Fall time tR, tF — — 10 ns SDIO Input, SEN to SCLKSetup Note: When selecting SPI mode, the user must ensure that a rising edge of SCLK does not occur within 300 ns before the rising edge of RST. SCLK 70% 30% tR tHIGH SEN 70% SDIO 70% tS tLOW tF tHSDIO tHSEN tS 30% C7 C6–C1 C0 D7 D6–D1 D0 30% Control Byte In 8 Data Bytes In Figure 6. SPI Control Interface Write Timing Parameters SCLK 70% 30% tCDV tS SEN 70% tHSEN tHSDIO tS 30% tCDZ SDIO 70% C7 C6–C1 C0 D7 D6–D1 D0 30% Control Byte In Bus Turnaround 16 Data Bytes Out (SDIO or GPO1) Figure 7. SPI Control Interface Read Timing Parameters 10 Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com Rev. 1.0 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • November 9, 2021 Si4720/21-B20 Table 8. Digital Audio Interface Characteristics (Receive) (VDD = 2.7 to 5.5 V, VIO = 1.5 to 3.6 V, TA = –20 to 85 °C) Parameter Symbol Test Condition Min Typ Max Unit DCLK Cycle Time tDCT 26 — 1000 ns DCLK pulse width high tDCH 10 — — ns DCLK pulse width low tDCL 10 — — ns DFS set-up time to DCLK rising edge tSU:DFS 5 — — ns DFS hold time from DCLK rising edge tHD:DFS 5 — — ns 0 — 12 ns DOUT propagation delay from DCLK falling edge tPD:DOUT tDCH tDCL DCLK tDCT DFS tHD:DFS tSU:DFS DOUT tPD:OUT Figure 8. Digital Audio Interface Timing Parameters, I2S Mode Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 11 Rev. 1.0 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • November 9, 2021 Si4720/21-B20 Table 9. FM Receiver Characteristics1,2 (VDD = 2.7 to 5.5 V, VIO = 1.5 to 3.6 V, TA = –20 to 85 °C) Parameter Symbol Input Frequency Test Condition fRF Min Typ Max Unit 76 — 108 MHz Sensitivity with Headphone Network3,4,5 (S+N)/N = 26 dB — 2.2 3.5 µV EMF Sensitivity with 50  Network3,4,5,6 (S+N)/N = 26 dB — 1.1 — µV EMF f = 2 kHz, RDS BLER < 5% — 15 — µV EMF TXO Receiver Mode Sensitivity6 — 3.5 — µV EMF LNA Input Resistance6,7 3 4 5 k LNA Input Capacitance6,7 4 5 6 pF 100 105 — dBµV EMF m = 0.3 40 50 — dB Adjacent Channel Selectivity ±200 kHz 35 50 — dB Alternate Channel Selectivity ±400 kHz 60 70 — dB In-band 35 — — dB Audio Output Voltage3,4,7 72 80 90 mVRMS Audio Output L/R Imbalance3,7,9 — — 1 dB RDS Sensitivity 6 Input IP36,8 AM Suppression3,4,6,7 Spurious Response Rejection6 Audio Frequency Response Low6 –3 dB — — 30 Hz Audio Frequency Response High6 –3 dB 15 — — kHz Audio Stereo Separation7,9 25 — — dB Audio Mono S/N3,4,5,7,10 55 63 — dB Audio Stereo S/N4,5,7,10,11 — 58 — dB Audio THD3,7,9 — 0.1 0.5 % FM_DEEMPHASIS = 2 70 75 80 µs FM_DEEMPHASIS = 1 45 50 54 µs De-emphasis Time Constant6 Audio Output Load Resistance6,10 RL Single-ended 10 — — k Audio Output Load Capacitance6,10 CL Single-ended — — 50 pF RCLK tolerance = 100 ppm — — 80 ms/channel Seek/Tune Time6 Notes: 1. Additional testing information is available in Application Note AN388. Volume = maximum for all tests. Tested at RF = 98.1 MHz. 2. To ensure proper operation and receiver performance, follow the guidelines in “AN383: Antenna Selection and Universal Layout Guidelines.” Skyworks will evaluate schematics and layouts for qualified customers. 3. FMOD = 1 kHz, 75 µs de-emphasis, MONO = enabled, and L = R unless noted otherwise. 4. f = 22.5 kHz. 5. BAF = 300 Hz to 15 kHz, A-weighted. 6. Guaranteed by characterization. 7. VEMF = 1 mV. 8. |f2 – f1| > 2 MHz, f0 = 2 x f1 – f2. AGC is disabled. Refer to "7. Pin Descriptions: Si4720/21-GM" on page 40. 9. f = 75 kHz. 10. At LOUT and ROUT pins. 11. Analog audio output mode. 12. At temperature 25 °C. 12 Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com Rev. 1.0 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • November 9, 2021 Si4720/21-B20 Table 9. FM Receiver Characteristics1,2 (Continued) (VDD = 2.7 to 5.5 V, VIO = 1.5 to 3.6 V, TA = –20 to 85 °C) Parameter Powerup Time6 RSSI Offset12 Symbol Test Condition Min Typ Max Unit From powerdown — — 110 ms Input levels of 8 and 60 dBµV at RF Input –3 — 3 dB Notes: 1. Additional testing information is available in Application Note AN388. Volume = maximum for all tests. Tested at RF = 98.1 MHz. 2. To ensure proper operation and receiver performance, follow the guidelines in “AN383: Antenna Selection and Universal Layout Guidelines.” Skyworks will evaluate schematics and layouts for qualified customers. 3. FMOD = 1 kHz, 75 µs de-emphasis, MONO = enabled, and L = R unless noted otherwise. 4. f = 22.5 kHz. 5. BAF = 300 Hz to 15 kHz, A-weighted. 6. Guaranteed by characterization. 7. VEMF = 1 mV. 8. |f2 – f1| > 2 MHz, f0 = 2 x f1 – f2. AGC is disabled. Refer to "7. Pin Descriptions: Si4720/21-GM" on page 40. 9. f = 75 kHz. 10. At LOUT and ROUT pins. 11. Analog audio output mode. 12. At temperature 25 °C. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 13 Rev. 1.0 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • November 9, 2021 Si4720/21-B20 Table 10. FM Transmitter Characteristics1 Test conditions: VRF = 118 dBµV, stereo, f = 68.25 kHz, fpilot = 6.75 kHz, REFCLK = 32.768 kHz, 75 µs pre-emphasis, unless otherwise specified. Production test conditions: VDD = 3.3 V, VIO = 3.3 V, TA = 25 °C, FRF = 98 MHz. Characterization test conditions: VDD = 2.7 to 5.5 V, VIO = 1.5 to 3.6 V, TA = –20 to 85 °C, FRF = 76–108 MHz. All minimum and maximum specifications are guaranteed and apply across the recommended operating conditions. Typical values apply at VDD = 3.3 V and 25 °C unless otherwise stated. Parameters are tested in production unless otherwise specified. Parameter Symbol Transmit Frequency Range 2 Test Condition fRF Transmit Frequency Accuracy and Stability2,3 Min Typ Max Unit 76 — 108 MHz –3.5 — 3.5 kHz Transmit Voltage Accuracy2 VRF = 103–117 dBµV –2.5 — 2.5 dB Transmit Voltage Accuracy VRF = 102, 118 dBµV –2.5 — 2.5 dB –0.075 — –0.025 dB/°C Transmit Voltage Temperature Coefficient2 Transmit Channel Edge Power > ±100 kHz, pre-emphasis off — — –20 dBc Transmit Adjacent Channel Power > ±200 kHz, pre-emphasis off — –30 –26 dBc Transmit Alternate Channel Power > ±400 kHz, pre-emphasis off — –30 –26 dBc In-band (76–108 MHz) — — –30 dBc CTUNE — 53 — pF CTUNE — 5 — pF TX_PREMPHASIS = 75 µs 70 75 80 µs TX_PREMPHASIS = 50 µs 45 50 54 µs Audio SNR Mono2 f = 22.5 kHz, Mono, limiter off 58 63 — dB Audio SNR Stereo f = 22.5 kHz, fpilot = 6.75 kHz, Stereo, limiter off 53 58 — dB Audio THD Mono f = 75 kHz, Mono, limiter off — 0.1 0.5 % f = 22.5 kHz, fpilot = 6.75 kHz, Stereo, limiter off — 0.1 0.5 % left channel only 30 35 — dB 40 50 — dB Transmit Emissions Output Capacitance Max 2 Output Capacitance Min2 Pre-emphasis Time Constant2 Audio THD Stereo2 Audio Stereo Separation2 Sub Carrier Rejection Ratio SCR Notes: 1. FM transmitter performance specifications are subject to adherence to Skyworks guidelines in “AN383: Universal Antenna Selection and Layout Guidelines.” Skyworks will evaluate schematics and layouts for qualified customers. Tested with test schematic (L = 120 nH, Q > 30) shown in Figure 10 on page 18. 2. Guaranteed by characterization. 3. No measurable fRF/VDD at VDD of 500 mVpk-pk at 100 Hz to 10 kHz. 14 Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com Rev. 1.0 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • November 9, 2021 Si4720/21-B20 Table 10. FM Transmitter Characteristics1 (Continued) Test conditions: VRF = 118 dBµV, stereo, f = 68.25 kHz, fpilot = 6.75 kHz, REFCLK = 32.768 kHz, 75 µs pre-emphasis, unless otherwise specified. Production test conditions: VDD = 3.3 V, VIO = 3.3 V, TA = 25 °C, FRF = 98 MHz. Characterization test conditions: VDD = 2.7 to 5.5 V, VIO = 1.5 to 3.6 V, TA = –20 to 85 °C, FRF = 76–108 MHz. All minimum and maximum specifications are guaranteed and apply across the recommended operating conditions. Typical values apply at VDD = 3.3 V and 25 °C unless otherwise stated. Parameters are tested in production unless otherwise specified. Parameter Symbol Test Condition Min Typ Max Unit — — 110 ms — — 0.636 VPK Mono, ±1.5 dB, f = 75 kHz, 0, 50, 75 µs pre-emphasis, limiter off 30 — 15 k Hz High Pass Corner Frequency2 Mono, –3 dB, f = 75 kHz, 0, 50, 75 µs pre-emphasis, limiter off 5 — 30 Hz Low Pass Corner Frequency2 Mono, –3 dB, f = 75 kHz, 0, 50, 75 µs pre-emphasis, limiter off 15 k — 16 k Hz Mono –1 — 1 dB f = 68.25 kHz, fpilot = 6.75 kHz, Stereo –10 — 10 % f = 68.25 kHz, fpilot = 6.75 kHz, Stereo –10 — 10 % LIATTEN[1:0] = 11 50 60 — k — 10 — pF — 54 — dBuV Powerup Settling Time2 Input Signal Level2 Frequency Flatness2 Audio Imbalance Pilot Modulation Rate Accuracy2 Audio Modulation Rate Accuracy2 Input Resistance2 Input Capacitance VAI 2 Received Noise Level Accuracy (Si4720/21 Only)2 60 dBµV input, TA = 25 ºC Notes: 1. FM transmitter performance specifications are subject to adherence to Skyworks guidelines in “AN383: Universal Antenna Selection and Layout Guidelines.” Skyworks will evaluate schematics and layouts for qualified customers. Tested with test schematic (L = 120 nH, Q > 30) shown in Figure 10 on page 18. 2. Guaranteed by characterization. 3. No measurable fRF/VDD at VDD of 500 mVpk-pk at 100 Hz to 10 kHz. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 15 Rev. 1.0 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • November 9, 2021 Si4720/21-B20 Table 11. Digital Audio Interface Characteristics (Transmit) (VDD = 2.7 to 5.5 V, VIO = 1.5 to 3.6 V, TA = –20 to 85 °C) Parameter Symbol Test Condition Min Typ Max Unit DCLK pulse width high tDCH 10 — — ns DCLK pulse width low tDCL 10 — — ns DFS set-up time to DCLK rising edge tSU:DFS 5 — — ns DFS hold time from DCLK rising edge tHD:DFS 5 — — ns DIN set-up time from DCLK rising edge tSU:DIN 5 — — ns DIN hold time from DCLK rising edge tHD:DIN 5 — — ns tR tF — — 10 ns 1.0 — 40.0 MHz DCLK, DFS, DIN, Rise/Fall time DCLK Tx Frequency1,2 Notes: 1. Guaranteed by characterization. 2. The DCLK frequency may be set below the minimum specification if DIGITAL_INPUT_SAMPLE_RATE is first set to 0 (disable). DCLK tR DFS DIN tHD:DFS tF tSU:DFS tSU:DIN tHD:DIN Figure 9. Digital Audio Interface Timing Parameters, I2S Mode 16 Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com Rev. 1.0 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • November 9, 2021 Si4720/21-B20 Table 12. FM Receive Power Scan Characteristics1 (VDD = 2.7 to 5.5 V, VIO = 1.5 to 3.6 V, TA = –20 to 85 °C, FRF = 76–108 MHz) Parameter Symbol Test Condition Tune and Signal Strength Measurement Time per Channel2 Min Typ Max Unit — — 80 ms Notes: 1. Settling time for ac coupling capacitors on the audio input pins after Receive to Transmit transition can take a few hundred milliseconds. The actual settling time depends on the values of the ac-coupling capacitors. Using digital audio input mode avoids this settling time. 2. Guaranteed by characterization. Table 13. Reference Clock and Crystal Characteristics (VDD = 2.7 to 5.5 V, VIO = 1.5 to 3.6 V, TA = –20 to 85 °C) Parameter Symbol Test Condition Min Typ Max Unit 31.130 32.768 40,000 kHz –50 — 50 ppm 1 — 4095 31.130 32.768 34.406 kHz — 32.768 — kHz –100 — 100 ppm — — 3.5 pF Reference Clock 1 RCLK Supported Frequencies RCLK Frequency Tolerance2 REFCLK_PRESCALE REFCLK Crystal Oscillator Crystal Oscillator Frequency Crystal Frequency Tolerance2 Board Capacitance Notes: 1. The Si4720/21 divides the RCLK input by REFCLK_PRESCALE to obtain REFCLK. There are some RCLK frequencies between 31.130 kHz and 40 MHz that are not supported. See “AN332: Si4704/05/06/1x/2x/3x/4x FM Transmitter/AM/FM/SW/LW/WB Receiver Programming Guide” for more details. 2. A frequency tolerance of ±50 ppm is required for FM seek/tune using 50 kHz channel spacing. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 17 Rev. 1.0 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • November 9, 2021 Si4720/21-B20 2. Test Circuit 2.1. Test Circuit Schematic C2 VIO FMI TX Antenna 16 15 0.47 µF 14 LOUT 13 ROUT 12 GND 11 VDD U1 Si4720/21 L1 120 nH LOUT ROUT VBATTERY 2.7 to 5.5 V VIO 22 nF 10 RCLK SDIO RST SEN SCLK SDIO RCLK VIO 1.5 to 3.6 V 9 7 8 R1 SCLK C1 6 VTXOUT 50  C4 RIN SEN 2 pF RIN C3 1 NC 2 FMI 3 RFGND 4 TXO 5 RST LIN LIN 17 GPO3 18 GPO2/INT 19 GPO1 NC 20 0.47 µF X1 C5 RCLK C6 Notes: 1. Si4720/21 is shown configured in I 2C compatible bus mode. 2. GPO2/INT can be configured for interrupts with the powerup command. 3. To ensure proper operation and FM transmitter performance, follow the guidelines in AN383: 3 mm x 3 mm QFN Universal Layout Guide Skyworks will evaluate schematics and layouts for qualified customers. 4. LIN, RIN line inputs must be ac-coupled. Figure 10. Test Circuit Schematic 2.2. Test Circuit Bill of Materials Table 14. Si4720/21 Test Circuit Bill of Materials Component(s) Value/Description Supplier(s) C1 Supply bypass capacitor, 22 nF, 20%, Z5U/X7R Murata C2, C3 AC Coupling Capacitor, 0.47 µF Murata C4 2 pF, ±.05 pF, 06035JZR0AB AVX C5, C6 Crystal load capacitors, 22 pF, ±5%, COG (Optional: for crystal oscillator option) Venkel L1 120 nH inductor, Qmin = 30 Murata R1 49.9 , 5% Murata X1 32.768 kHz crystal (Optional: for crystal oscillator option) Epson U1 Si4720/21 FM Radio Transceiver Skyworks 18 Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com Rev. 1.0 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • November 9, 2021 Si4720/21-B20 3. Typical Application Schematic 3.1. Analog Audio Inputs/Outputs C2 VIO 1 RX Antenna TX/RX Antenna 16 RIN 15 RIN 14 LOUT 13 ROUT 12 GND 11 VDD NC 2 FMI 3 RFGND 4 TXO 5 RST LIN LIN 17 GPO3 18 GPO2/INT 19 GPO1 NC 20 0.47 µF U1 Si4720/21 L1 120 nH C3 0.47 µF LOUT ROUT VBATTERY 2.7 to 5.5 V RST VIO 22 nF 10 RCLK 9 SDIO 8 SCLK 7 6 SEN C1 SEN SCLK SDIO RCLK VIO 1.5 to 3.6 V X1 C4 RCLK C5 Notes: 1. Si4720/21 is shown configured in I2 C compatible bus mode. 2. GPO2/INT can be configured for interrupts with the powerup command. 3. To ensure proper operation and FM transmitter performance, follow the guidelines in AN383: 3 mm x 3 mm QFN Universal Layout Guide Skyworks will evaluate schematics and layouts for qualified customers. 4. LIN, RIN line inputs must be ac-coupled. 5. Dedicated RX antenna at FMI input optional. Figure 11. Analog Audio Inputs/Outputs (LIN, RIN, LOUT, ROUT) 3.2. Typical Application Bill of Materials Table 15. Si4720/21 Typical Application Bill of Materials Component(s) Value/Description Supplier(s) C1 Supply bypass capacitor, 22 nF, 20%, Z5U/X7R Murata C2, C3 AC Coupling Capacitor, 0.47 µF Murata C4, C5 Crystal load capacitors, 22 pF, ±5%, COG (Optional: for crystal oscillator option) Venkel L1 120 nH inductor, Qmin = 30 Murata X1 32.768 kHz crystal (Optional: for crystal oscillator option) Epson U1 Si4720/21 FM Radio Transceiver Skyworks Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 19 Rev. 1.0 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • November 9, 2021 Si4720/21-B20 3.3. Digital Audio Inputs/Outputs R1 RX Antenna TX/RX Antenna NC FMI RFGND TXO RST DCLK 16 DFS DOUT DFS 18 17 GPO3/DCLK 1 2 3 4 5 GPO2/INT 19 GPO1 NC 20 VIO DOUT DFS DIN GND V DD U1 Si4720/21 15 14 13 12 11 L1 120 nH VIO 22 nF VBATTERY 2.7 to 5.5 V 10 RCLK 9 SDIO 8 SCLK 7 SEN 6 DIN R3 C1 RST DFS R2 SEN SCLK SDIO RCLK V IO 1.5 to 3.6 V Notes: 1. Si4720/21 is shown configured in I2C compatible bus mode. 2. GPO2/INT can be configured for interrupts with the powerup command. 3. To ensure proper operation and FM transmitter performance, follow the guidelines in AN383: Si47xx 3 mm x 3 mm QFN Universal Layout Guide.‫ ﺴ‬Skyworks will evaluate schematics and layouts for qualified customers. 4. Dedicated RX antenna at FMI input optional. Figure 12. Digital Audio Inputs (DIN, DFS, DCLK) 3.4. Typical Application Schematic Bill of Materials Table 16. Si4720/21 Bill of Materials Component(s) Value/Description Supplier(s) C1 Supply bypass capacitor, 22 nF, 20%, Z5U/X7R Murata C2, C3 AC Coupling Capacitor, 0.47 µF Murata L1 120 nH inductor, Qmin = 30 Murata R1, R2 2 k Resistor Any R3 600  Resistor Any U1 Si4720/21 FM Radio Transceiver Skyworks 20 Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com Rev. 1.0 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • November 9, 2021 Si4720/21-B20 4. Universal AM/FM RX/FM TX Application Schematic Figure 13 shows an application schematic that supports the Si47xx family of 3 mm x 3 mm QFN products, including the Si4702/3/4/5 FM receivers, Si471x FM transmitters, Si472x FM transceivers, and Si473x AM/FM receivers. R2 FB1 2.5 k @ 100 MHz Right Audio Left Audio T5 U2 Headphone Amplifier FB2 2.5 k @ 100 MHz S1 Si4702/03: Populate R12, R13, R21, C14, and C15 Si4704/05/1x/2x/3x Analog: Populate C7, C8, C14 and C15 as shown Si4704/05/1x/2x/3x Digital: Populate R16, R17, R18, R19, and R20 as shown J1 HP Jack R16 2 k C4 1 nF LHEADPHONE 270 nH VBATTERY 2.7 to 5.5 V System Component GPIO3 GPIO2 GPIO1 R13 0 C7/R17 0.39 uF/ 2 k LIN System Component D3 L1 10 nH D4 LSHORT 120 nH System Component System Component AM Ferrite Antenna C17/R21 3.3pF/0  1 2 RIN NC GPO1 GPO2/IRQ GPO3/DCLK LIN/DFS R14 0 20 19 18 17 16 FM Embedded RX/TX Antenna NC FMI 3 RFGND 4 TXO/AMI R12 0 GND/RIN/DOUT U1 Si47xx 5 RST LOUT/DFS 15 14 13 ROUT/DIN 12 GND V 11 C15/R20 DD C16 470 nF VBATTERY 0.39 uF/ 0  2.7 to 5.5 V System Components 22 nF 6 7 8 9 10 LFERRITE 180– 600 uH SEN SCLK SDIO RCLK VIO C1 D5 C8/R18 0.39 uF/ 600  C14/R19 0.39 uF/ 0  RST SEN SCLK SDIO RCLK VIO Figure 13. Universal AM/FM RX/FM TX Application Schematic Following the schematic and layout recommendations detailed in “AN383: Universal Antenna Selection and Layout Guidelines” will result in optimal performance with the minimal application schematic shown in Figure 13. “Universal AM/FM RX/FM TX Application Schematic”. System components are those that are likely to be present for any tuner or transmitter design. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 21 Rev. 1.0 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • November 9, 2021 Si4720/21-B20 4.1. Universal AM/FM RX/FM TX Bill of Materials The bill of materials for the expanded application schematic shown in Figure 13 is provided in Table 17. Refer to the individual device layout guides and antenna interface guides for a discussion of the purpose of each component. Table 17. Universal AM/FM/RX/FM TX Bill of Materials Designator Description C1 Supply bypass capacitor, 22 nF, 10%, Z5U/X7R, 0402 U1 Skyworks Si47xx, 3 mm x 3 mm, 20 pin, QFN R12, R13, R19, 0  jumper, 0402 R20, R21 Note R12, R13, and R21 for Si4702/03 Only AM antenna ac coupling capacitor, 470 nF, 20%, Z5U/X7R AM Ferrite Antenna AM Ferrite loop stick, 180–600 µH AM Ferrite Antenna Ferrite bead, 2.5 k @ 100 MHZ, 0603, Murata BLM18BD252SN1D Headphone Antenna LHEADPHONE Headphone antenna matching inductor, 270 nH, 0603, Q>15, Murata Headphone Antenna C16 LFERRITE FB1,FB2 LQW18ANR27J00D Embedded antenna matching inductor, 120 nH, 0603, Q>30, Murata LQW18ANR12J00D Embedded Antenna R14 Embedded antenna jumper, 2.2 , 0402 Optional C2 Supply bypass capacitor, 22 nF, 10%, Z5U/X7R, 0402 Optional C3 Supply bypass capacitor, 100 nF, 10%, Z5U/X7R, 0402 Optional LSHORT C5, C6 Headphone amp output shunt capacitor, 100 pF, 10%, Z5U/X7R, 0402 Optional R7-R11 Current limiting resistor, 20 –2 k, 0402 Optional Crystal load capacitor, 22 pF, 5%, COG Optional Crystal, Epson FC-135 Optional C7, C8 Si47xx input ac coupling capacitor, 0.39 µF, X7R/X5R, 0402 System Component D1-D5 ESD Diode, SOT23-3, California Micro Devices CM1214-01ST System Component C11 Supply bypass capacitor, 100 nF, 10%, Z5U/X7R, 0402 Headphone Amplifier C4 Headphone antenna ac coupling capacitor, 1 nF, 10%, Z5U/X7R, 0402 Headphone Antenna C12, C13 X1 C9, C10 Headphone amp output ac coupling capacitor, 125 uF, X7R, 0805 C14, C15 Headphone amp input ac coupling capacitor, 0.39 µF, X7R/X5R, 0402 Headphone Amplifier R1,R2,R3,R4 R5, R6 U2 R16, R17 R18 L1 C17 Headphone Amplifier Headphone amp feedback/gain resistor, 20 k, 0402 Headphone Amplifier Headphone amp bleed resistor, 100 k, 0402 Headphone Amplifier Headphone amplifier, National Semiconductor, LM4910MA Headphone Amplifier Current limiting resistor, 2 k0402 System Component Current limiting resistor, 600 , 0402 System Component VCO filter inductor, 10 nH, 0603, Q30, Murata, LQW18ANR01J00D Optional VCO filter capacitor, 3.3 pF, 0402, COG, Venkel, C0402COG2503R3JN Optional 22 Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com Rev. 1.0 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • November 9, 2021 Si4720/21-B20 5. Functional Description 5.1. Overview Si4720 Tx/Rx Ant TXO LIN L1 120 nH RIN ADC ADC VDD CONTROL INTERFACE SEN GPO GPO3 *Note: Dedicated Rx antenna is optional AFC GPO2/INT LDO GPO1 GND C1 22 uF RCLK 2.7–5.5 V LOUT VIO AGC DAC DSP RST PGA RFGND ROUT SDIO LNA DAC SCLK FMI MUX Rx Ant* Figure 14. Functional Block Diagram The Si4720/21 is the first single-chip FM radio transceiver. The proven and patented digital architecture of the Si4720/21 combines the functionality of the Si470x FM radio receiver with the Si471x FM transmitter, offering full FM receive and transmit capabilities in a single, ultra-small 3x3x0.55 mm QFN package. The device leverages Skyworks’ highly successful and proven FM technology and offers unmatched integration and performance. FM receiver and transmit functionality may be added to any portable device by using this single chip. As with the Si470x and Si471x products, the Si4720/21 offers industry leading size, performance, low power consumption, and ease of use. The Si4720/21 is the first FM radio transceiver integrated circuit to support a small loop antenna, which can be integrated into the enclosure or PCB of a portable device. This feature enables applications that also include Bluetooth functionality to perform FM radio reception without cables. For portable navigation devices, the Si4720’s antenna architecture permits integration of the traffic messaging antenna into the enclosure of the portable device, and eliminates the need for external antenna cables. The Si4720's digital integration reduces the required external components of traditional offerings, resulting in a solution requiring only an external inductor and bypass capacitor, and a PCB space of approximately 15 mm2. The Si4720/21 is layout compatible with Skyworks' Si470x FM radio receivers, Si473x AM/FM radio receivers, and the Si471x FM radio transmitter solutions, allowing a single PCB layout to accommodate a variety of music features. High yield manufacturability, unmatched performance, easy design-in, and software programmability are key advantages of the Si4720. The Si4720/21’s integrated receive power scan function shares the same antenna as the transmitter allowing for a compact printed circuit board design. The device operates in half duplex mode, meaning the transmitter and receiver do not operate at the same time. The Si4720/21 performs FM modulation in the digital domain to achieve high fidelity, optimal performance versus power consumption, and flexibility of design. The onboard DSP provides modulation adjustment and audio dynamic range control for optimum sound quality. The Si4721 supports the European Radio Data System (RDS) and the US Radio Broadcast Data System (RBDS) including all the symbol encoding, block synchronization, and error correction functions. Using this feature, the Si4721 enables data such as artist name and song title to be transmitted to an RDS/RBDS receiver. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 23 Rev. 1.0 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • November 9, 2021 Si4720/21-B20 The transmit output (TXO) connects directly to the transmit antenna with only one external inductor to provide harmonic filtering. The output is programmable over a 10 dB voltage range in 1 dB steps. The TXO output pin can also be configured for loop antenna support. Users are responsible for complying with local regulations on RF transmission (FCC, ETSI, ARIB, etc.). The digital audio interface operates in slave mode and supports a variety of MSB-first audio data formats including I2S and left-justified modes. The interface has three pins: digital data input (DIN), digital frame synchronization input (DFS), and a digital bit synchronization input clock (DCLK). The Si4720/21 supports a number of industry-standard sampling rates including 32, 40, 44.1, and 48 kHz. The digital audio interface enables low-power operation by eliminating the need for redundant DACs and ADCs on the audio baseband processor. The Si4720/21 includes a low-noise stereo line input (LIN/RIN) with programmable attenuation. To ensure optimal audio performance, the Si4720/21 has a transmit line input property that allows the user to specify the peak amplitude of the analog input required to reach maximum deviation level. The deviation levels of the audio, pilot, and RDS/RBDS signals can be independently programmed to customize FM transmitter designs. The Si4720/21 has a programmable low audio level and high audio level indicators that allows the user to selectively enable and disable the carrier based on the presence of audio content. In addition, the device provides an overmodulation indicator to allow the user to dynamically set the maximum deviation level. The Si4720/21 has a programmable audio dynamic range control that can be used to reduce the dynamic range of the audio input signal and increase the volume at the receiver. These features can dramatically improve the end user’s listening experience. The Si4720/21 is reset by applying a logic low on the RST pin. This causes all register values to be reset to their default values. The digital input/output interface supply (VIO) provides voltage to the RST, SEN, SDIO, RCLK, DIN, DFS, and DCLK pins and can be connected to the audio baseband processor's supply voltage to save power and remove the need for voltage level translators. RCLK is not required for register operation. The Si4720/21 reference clock is programmable, supporting many RCLK inputs as shown in Table 10. The S4720/21 are part of a family of broadcast audio solutions offered in standard, 3 x 3 mm 20-pin QFN packages. All solutions are layout compatible, allowing a single PCB to accommodate various feature offerings. The Si4720/21 includes line inputs to the on-chip analog-to-digital converters (ADC), a programmable reference clock input, and a configurable digital audio interface. The chip supports I2C-compliant 2-wire, 8-bit SPI, and a 3-wire control interface. 5.2. Application Schematics and Operating Modes The application schematic for the Si4720/21 is shown in Section "3. Typical Application Schematic" on page 19. The Si4720/21 supports selectable analog, digital, or concurrent analog and digital audio output modes. In the analog output mode, pin 13 is ROUT, pin 14 is LOUT, and pin 17 is GPO3. In the digital output mode, pin 15 is DOUT, pin 16 is DFS, and pin 17 is DCLK. Concurrent analog and digital audio output mode requires pins 13, 14, 15, 16, and 17. In addition to output mode, there is a clocking mode to clock the Si4720/21 from a reference clock or crystal oscillator. The user sets the operating modes with commands as described in Section "6. Commands and Properties" on page 35. 5.3. FM Receiver The Si4720/21 FM receiver is based on the proven Si4700/01/02/03 FM radio receiver. The part leverages Skyworks' proven and patented Si4700/01 FM broadcast radio receiver digital architecture, delivering superior RF performance and interference rejection. The proven digital techniques provide excellent sensitivity in weak signal environments while providing superb selectivity and inter-modulation immunity in strong signal environments. The FM receiver supports the worldwide FM broadcast band (76 to 108 MHz) with channel spacings of 50– 200 kHz. The Low-IF architecture utilizes a single converter stage and digitizes the signal using a highresolution analog-to-digital converter. The resulting digital signals are further processed through an on-chip DSP for digital channel selection, FM demodulation, and ultimately stereo audio output. The audio output can be directed either to an external headphone amplifier via analog in/out or to other system ICs through digital audio interface (I2S). 24 Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com Rev. 1.0 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • November 9, 2021 Si4720/21-B20 5.4. Integrated Antenna Support 5.5. Receiver Digital Audio Interface (Si4721 Only) The Si4720/21 is the first FM receiver to support the fast growing trend to integrate the FM receiver antenna into the device enclosure. The chip is designed with this function in mind from the outset, with multiple international patents pending, thus it is superior to many other options in price, board space, and performance. The Si4720/21 supports an internal RX antenna allowing for "wire free" listening to FM over Bluetooth. The user can receive FM over the integrated RX antenna and stream it via Bluetooth to a Bluetoothenabled headset. Testing indicates that using Skyworks' patented techniques provides FM performance over an integrated antenna that can be very similar in many key metrics to performance using standard FM receive antennas (e.g., wired headset). Refer to “AN383: Antenna Selection and Universal Layout Guidelines” for additional details on the implementation of support for an integrated antenna. Figure 15 shows a conceptual block diagram of the Si4720/21 architecture used to support the short antenna. The headphone/dedicated FM receive antenna is therefore optional. Host software can detect the presence of a headphone antenna and switch between the integrated antenna if desired. Headphone Ant* FMI RFGND LNA AGC Short/ Embedded Ant LPI L1 120 nH *Note: Dedicated RX antenna is optional. The digital audio interface operates in slave mode and supports three different audio data formats: I2S  Left-Justified  DSP Mode  5.5.1. Audio Data Formats In I2S mode, by default the MSB is captured on the second rising edge of DCLK following each DFS transition. The remaining bits of the word are sent in order, down to the LSB. The left channel is transferred first when the DFS is low, and the right channel is transferred when the DFS is high. In Left-Justified mode, by default the MSB is captured on the first rising edge of DCLK following each DFS transition. The remaining bits of the word are sent in order, down to the LSB. The left channel is transferred first when the DFS is high, and the right channel is transferred when the DFS is low. In DSP mode, the DFS becomes a pulse with a width of 1DCLK period. The left channel is transferred first, followed right away by the right channel. There are two options in transferring the digital audio data in DSP mode: the MSB of the left channel can be transferred on the first rising edge of DCLK following the DFS pulse or on the second rising edge. In all audio formats, depending on the word size, DCLK frequency, and sample rates, there may be unused DCLK cycles after the LSB of each word before the next DFS transition and MSB of the next word. In addition, if preferred, the user can configure the MSB to be captured on the falling edge of DCLK via properties. The number of audio bits can be configured for 8, 16, 20, or 24 bits. 5.5.2. Audio Sample Rates The device supports a number of industry-standard sampling rates including 32, 40, 44.1, and 48 kHz. The digital audio interface enables low-power operation by eliminating the need for redundant DACs on the audio baseband processor. Figure 15. Conceptual Block Diagram of the Si4720/21 Short Antenna Support Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 25 Rev. 1.0 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • November 9, 2021 Si4720/21-B20 (OFALL = 1) INVERTED DCLK (OFALL = 0) DCLK LEFT CHANNEL DFS I2S (OMODE = 0000) RIGHT CHANNEL 1 DCLK DOUT 1 DCLK 1 2 n-2 3 n-1 MSB n 1 LSB MSB 2 n-2 3 n-1 n LSB Figure 16. I2S Digital Audio Format (OFALL = 1) INVERTED DCLK (OFALL = 0) DCLK DFS LEFT CHANNEL RIGHT CHANNEL Left-Justified (OMODE = 0110) 1 DOUT 2 3 n-2 n-1 MSB n 1 LSB MSB 2 n-2 3 n-1 n LSB Figure 17. Left-Justified Digital Audio Format (OFALL = 0) DCLK DFS RIGHT CHANNEL LEFT CHANNEL (OMODE = 1100) DOUT (MSB at 1st rising edge) 1 2 3 n-2 n-1 MSB (OMODE = 1000) 1 LSB MSB n-1 n 1 LSB MSB 2 3 n-2 1 2 3 n-2 MSB n-1 n LSB LEFT CHANNEL 1 DCLK DOUT (MSB at 2nd rising edge) n RIGHT CHANNEL 2 3 n-2 n-1 n LSB Figure 18. DSP Digital Audio Format 5.6.1. Stereo Decoder The output of the FM demodulator is a stereo multiplexed (MPX) signal. The MPX standard was developed in 1961, and is used worldwide. Today's MPX signal format consists of left + right (L+R) audio, left – right (L–R) audio, a 19 kHz pilot tone, and RDS/RBDS data as shown in Figure 19 below. The Si4720/21's integrated stereo decoder automatically decodes the MPX signal using DSP techniques. The 0 to 15 kHz (L+R) signal is the mono output of the FM tuner. Stereo is generated from the (L+R), (L–R), and a 19 kHz pilot tone. The pilot tone is used as a reference to recover the (L–R) signal. Output left and right channels are obtained by adding and subtracting the (L+R) and (L–R) signals respectively. The Si4721 uses frequency information from the 19 kHz stereo pilot to recover the 57 kHz RDS/RBDS signal. Modulation Level 5.6. Stereo Audio Processing Mono Audio Left + Right 0 Stereo Pilot 15 19 23 5.6.2. Stereo-Mono Blending Stereo Audio Left - Right 38 Frequency (kHz) Figure 19. MPX Signal Spectrum RDS/ RBDS 53 57 Adaptive noise suppression is employed to gradually combine the stereo left and right audio channels to a mono (L+R) audio signal as the signal quality degrades to maintain optimum sound fidelity under varying reception conditions. Stereo/mono status can be monitored with the FM_RSQ_STATUS command. Mono operation can be forced with the FM_BLEND_MONO_THRESHOLD property. 26 Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com Rev. 1.0 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • November 9, 2021 Si4720/21-B20 5.7. De-Emphasis Pre-emphasis and de-emphasis is a technique used by FM broadcasters to improve the signal-to-noise ratio of FM receivers by reducing the effects of high-frequency interference and noise. When the FM signal is transmitted, a pre-emphasis filter is applied to accentuate the high audio frequencies. The Si4720/21 incorporates a de-emphasis filter which attenuates high frequencies to restore a flat frequency response. Two time constants are used in various regions. The deemphasis time constant is programmable to 50 or 75 µs and is set by the FM_DEEMPHASIS property. 5.8. Stereo DAC High-fidelity stereo digital-to-analog converters (DACs) drive analog audio signals onto the LOUT and ROUT pins. The audio output may be muted. Volume is adjusted digitally with the RX_VOLUME property. 5.9. Soft Mute The soft mute feature is available to attenuate the audio outputs and minimize audible noise in very weak signal conditions. The softmute attenuation level is adjustable using the FM_SOFT_MUTE_MAX_ATTENUATION property. 5.10. RDS/RBDS Processor (Si4721 Only) The Si4721 implements an RDS/RBDS* processor for symbol decoding, block synchronization, error detection, and error correction. The Si4721 device is user configurable and provides an optional interrupt when RDS is synchronized, loses synchronization, and/or the user configurable RDS FIFO threshold has been met. The Si4721 reports RDS decoder synchronization status and detailed bit errors in the information word for each RDS block with the FM_RDS_STATUS command. The range of reportable block errors is 0, 1–2, 3–5, or 6+. More than six errors indicates that the corresponding block information word contains six or more non-correctable errors or that the block checkword contains errors. *Note: RDS/RBDS is referred to only as RDS throughout the remainder of this document. 5.11. Tuning The frequency synthesizer uses Skyworks’ proven technology, including a completely integrated VCO. The frequency synthesizer generates the quadrature local oscillator signal used to downconvert the RF input to a low intermediate frequency. The VCO frequency is locked to the reference clock and adjusted with an automatic frequency control (AFC) servo loop during reception. The tuning frequency can be directly programmed using the FM_TUNE_FREQ and command. The Si4720/21 supports channel spacing of 50, 100, or 200 kHz in FM receiver mode. 5.12. Seek Seek tuning will search up or down for a valid channel. Valid channels are found when the receive signal strength indicator (RSSI) and the signal-to-noise ratio (SNR) values exceed the set threshold. Using the SNR qualifier rather than solely relying on the more traditional RSSI qualifier can reduce false stops and increase the number of valid stations detected. Seek is initiated using the FM_SEEK_START command. The RSSI and SNR threshold settings are adjustable using properties (see Table 15). Two seek options are available. The device will either wrap or stop at the band limits. If the seek operation is unable to find a channel, the device will indicate failure and return to the channel selected before the seek operation began. 5.13. Reference Clock The Si4720/21 reference clock is programmable, supporting RCLK frequencies in Table 13. Refer to Table 3, “DC Characteristics,” on page 5 for switching voltage levels and Table 9, “FM Receiver Characteristics,” on page 12 for frequency tolerance information. An onboard crystal oscillator is available to generate the 32.768 kHz reference when an external crystal and load capacitors are provided. Refer to "3. Typical Application Schematic" on page 19. This mode is enabled using the POWER_UP command. Refer to Table 21 "Si472x Property Summary". The Si4720/21 performance may be affected by data activity on the SDIO bus when using the integrated internal oscillator. SDIO activity results from polling the tuner for status or communicating with other devices that share the SDIO bus. If there is SDIO bus activity while the Si4720/21 is performing the seek/tune function, the crystal oscillator may experience jitter, which may result in mistunes, false stops, and/or lower SNR. For best seek/tune results, Skyworks recommends that all SDIO data traffic be suspended during Si4720/21 seek and tune operations. This is achieved by keeping the bus quiet for all other devices on the bus, and delaying tuner polling until the tune or seek operation is complete. The seek/tune complete (STC) interrupt should be used instead of polling to determine when a seek/tune operation is complete. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 27 Rev. 1.0 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • November 9, 2021 Si4720/21-B20 5.14. FM Transmitter The transmitter (TX) integrates a stereo audio ADC to convert analog audio signals to high fidelity digital signals. Alternatively, digital audio signals can be applied to the Si4720/21 directly to reduce power consumption by eliminating the need to convert audio baseband signals to analog and back again to digital. Digital signal processing is used to perform the stereo MPX encoding and FM modulation to a low digital IF. Transmit baseband filters suppress out-of-channel noise and images from the digital low-IF signal. A quadrature single-sideband mixer up-converts the digital IF signal to RF, and internal RF filters suppress noise and harmonics to support the harmonic emission requirements of cellular phones, GPS, WLAN, and other wireless standards. The TXO output has over 10 dB of output level control, programmable in approximately 1 dB steps. This large output range enables a variety of antennas to be used for transmit, such as a monopole stub antenna or a loop antenna. The 1 dB step size provides fine adjustment of the output voltage. The TXO output requires only one external 120 nH inductor. The inductor is used to resonate the antenna and is automatically calibrated within the integrated circuit to provide the optimum output level and frequency response for supported transmit frequencies. Users are responsible for adjusting their system’s radiated power levels to comply with local regulations on RF transmission (FCC, ETSI, ARIB, etc.). 5.15. Receive Power Scan The Si4720/21 is the industry’s first FM transmitter with integrated receive functionality to measure received signal strength. This has been designed to specifically handle various antenna lengths including integrated PCB antennas, wire antennas, and loop antennas, allowing it to share the same antenna as the transmitter. The receive function reuses the on-chip varactor from the transmitter to optimize the receive signal power applied to the front-end amplifier. Auto-calibration of the varactor occurs with each tune command for consistent performance across the FM band. frequency deviation of 75 kHz corresponds to 100 percent modulation). Frequency deviation is related to the amplitude of the MPX signal by a gain constant, KVCO, as given by the following equation: f = K VCO A m where f is the frequency deviation; KVCO is the voltage-to-frequency gain constant, and Am is the amplitude of the MPX message signal. For a fixed KVCO, the amplitude of all the subchannel signals within the MPX message signal must be scaled to give the appropriate total frequency deviation. MPX Encoder RDS(t) C2 57 kHz L(t) C0 Frequency Tripler 38 kHz Frequency Doubler m(t) C1 19 kHz C0 R(t) Figure 20. MPX Encoder Figure 20 shows a conceptual block diagram of an MPX encoder used to generate the MPX signal. L(t) and R(t) denote the time domain waveforms from the left and right audio channels, and RDS(t) denotes the time domain waveform of the RDS/RBDS signal. The MPX message signal can be expressed as follows: m(t) = C0[L(t) + R(t)] + C1 cos(219 kHz) + C0[L(t) – R(t)] cos(238 kHz) + C2RDS(t) cos(257 kHz) Figure 19 shows an example modulation level breakdown for the various components of a typical MPX signal. where C0, C1, and C2 are gains used to scale the amplitudes of the audio signals (L(t) ± R(t)), the 19 kHz pilot tone, and the RDS subcarrier respectively, to generate the appropriate modulation level. To achieve the modulation levels of Figure 20 with KVCO = 75 kHz/V, C0 would be set to 0.45; C1 would be set to 0.1, and C2 would be set to 0.0267 giving a peak audio frequency deviation of 0.9 x 75 kHz = 67.5 kHz, a peak pilot frequency deviation of 0.1 x 75 kHz = 7.5 kHz, and a peak RDS frequency deviation of 0.0267 x 75 kHz = 2.0025 kHz for a total peak frequency deviation of 77.0025 kHz. The total modulation level for the MPX signal shown in Figure 19, assuming no correlation, is equal to the arithmetic sum of each of the subchannel levels resulting in 102.67 percent modulation or a peak frequency deviation of 77.0025 kHz (an instantaneous In the Si4720/21, the peak audio, pilot, and RDS frequency deviations can be programmed directly with the Transmit Audio, Pilot, and RDS Deviation commands with an accuracy of 10 Hz. For the example in Figure 20, the Transmit Audio Deviation is 5.15.1. Stereo Encoder 28 Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com Rev. 1.0 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • November 9, 2021 Si4720/21-B20 programmed with the value 6750, the Transmit Pilot Deviation with 750, and the Transmit RDS Deviation with 200, generating peak audio frequency deviations of 67.5 kHz, peak pilot deviations of 7.5 kHz, and peak RDS deviations of 2.0 kHz for a total peak frequency deviation of 77 kHz. The total peak transmit frequency deviation of the Si4720/21 can range from 0 to 100 kHz and is equal to the arithmetic sum of the Transmit Audio, Pilot, and RDS deviations. Users must comply with local regulations on radio frequency transmissions. Each of the individual deviations (transmit audio, pilot, and RDS) can be independently programmed; however, the total peak frequency deviation cannot exceed 100 kHz. The Si4720/21 provides an overmodulation indicator to allow the user to dynamically set the maximum deviation level. If the instantaneous frequency exceeds the deviation level specified by the TX_AUDIO_DEVIATION property, the SQINT interrupt bit (and optional interrupt) will be set. 5.16. Transmitter Digital Audio Interface The digital audio interface operates in slave mode and supports 3 different audio data formats: 1. I2S 2. Left-Justified 3. DSP Mode 5.16.1. Audio Data Formats In I2S mode, the MSB is captured on the second rising edge of DCLK following each DFS transition. The remaining bits of the word are sent in order, down to the LSB. The Left Channel is transferred first when the DFS is low, and the Right Channel is transferred when the DFS is high. (IFALL = 1) INVERTED DCLK (IFALL = 0) DCLK I2S (IMODE = 0000) In Left-Justified mode, the MSB is captured on the first rising edge of DCLK following each DFS transition. The remaining bits of the word are sent in order, down to the LSB. The Left Channel is transferred first when the DFS is high, and the Right Channel is transferred when the DFS is low. In DSP mode, the DFS becomes a pulse with a width of 1 DCLK period. The Left Channel is transferred first, followed right away by the Right Channel. There are two options in transferring the digital audio data in DSP mode: the MSB of the left channel can be transferred on the first rising edge of DCLK following the DFS pulse or on the second rising edge. In all audio formats, depending on the word size, DCLK frequency and sample rates, there may be unused DCLK cycles after the LSB of each word before the next DFS transition and MSB of the next word. The number of audio bits can be configured for 8, 16, 20, or 24 bits. 5.16.2. Audio Sample Rates The device supports a number of industry-standard sampling rates including 32, 40, 44.1, and 48 kHz. The digital audio interface enables low-power operation by eliminating the need for redundant DACs and ADCs on the audio baseband processor. The sampling rate is selected using the DIGITAL_INPUT_SAMPLE_RATE property. The device supports DCLK frequencies above 1 MHz. After powerup the DIGITAL_INPUT_SAMPLE_RATE property defaults to 0 (disabled). After DCLK is supplied, the DIGITAL_INPUT_SAMPLE_RATE property should be set to the desired audio sample rate such as 32, 40, 44.1, or 48 kHz. The DIGITAL_INPUT_SAMPLE_RATE property must be set to 0 before DCLK is removed or the DCLK frequency drops below 1 MHz. A device reset is required if this requirement is not followed. LEFT CHANNEL DFS RIGHT CHANNEL 1 DCLK DIN/DOUT 1 MSB 1 DCLK 2 3 n-2 n-1 n 1 LSB MSB 2 3 n-2 n-1 n LSB Figure 21. I2S Digital Audio Format Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 29 Rev. 1.0 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • November 9, 2021 Si4720/21-B20 (IFALL = 1) INVERTED DCLK (IFALL = 0) DCLK DFS LEFT CHANNEL RIGHT CHANNEL Left-Justified (IMODE = 0110) DIN/DOUT 1 2 3 n-2 n-1 MSB n 1 LSB MSB 2 n-1 n-2 3 n LSB Figure 22. Left-Justified Digital Audio Format (IFALL = 0) DCLK DFS RIGHT CHANNEL LEFT CHANNEL DIN/DOUT (MSB at 1 rising edge) (IMODE = 1100) 1 st 2 3 n-2 n-1 MSB (IMODE = 1000) 1 LSB MSB n-1 n 1 LSB MSB 2 3 n-2 1 2 3 MSB n-2 n-1 n LSB LEFT CHANNEL 1 DCLK DIN/DOUT (MSB at 2 rising edge) nd n RIGHT CHANNEL 2 3 n-2 n-1 n LSB Figure 23. DSP Digital Audio Format 5.17. Line Input The Si4720/21 provides left and right channel line inputs (LIN and RIN). The inputs are high-impedance and low-capacitance, suited to receiving line level signals from external audio baseband processors. Both line inputs are low-noise inputs with programmable attenuation. Passive and active anti-aliasing filters are incorporated to prevent high frequencies from aliasing into the audio band and degrading performance. To ensure optimal audio performance, the Si4720/21 has a TX_LINE_INPUT_LEVEL property that allows the user to specify the peak amplitude of the analog input (LILEVEL[9:0]) required to reach the maximum deviation level programmed in the audio deviation property, TX_AUDIO_DEVIATION. A corresponding line input attenuation code, LIATTEN[1:0], is also selected by the expected peak amplitude level. Table 18 shows the line attenuation codes. Table 18. Line Attenuation Codes LIATTEN[1:0] Peak Input Voltage [mV] RIN/LIN Input Resistance [k] 00 190 396 01 301 100 10 416 74 11 636 60 The line attenuation code is chosen by picking the lowest Peak Input Voltage in Table 18 that is just above the expected peak input voltage coming from the audio baseband processor. For example, if the expected peak input voltage from the audio baseband processor is 400 mV, the user chooses LIATTEN[1:0] = 10 since the Peak Input Voltage of 416 mV associated with LIATTEN[1:0] = 10 is just greater than the expected peak input voltage of 400 mV. The user also enters 400 mV into the LILEVEL[9:0] to associate this input level to the maximum frequency deviation level programmed into the audio deviation property. Note that selecting a particular value of LIATTEN[1:0] changes the input resistance of the LIN and RIN pins. This feature is used for cases where the expected peak input level exceeds the maximum input level of the LIN and RIN pins. The maximum analog input level is 636 mVpK. If the analog input level from the audio baseband processor exceeds this voltage, series resistors must be inserted in front of the LIN and RIN pins to attenuate the voltage such that it is within the allowable operating range. For example, if the audio baseband's expected peak amplitude is 900 mV and the VIO supply voltage is 1.8 V, the designer can use 30 k series resistors in front of the LIN and RIN pins and select LIATTEN[1:0] = 11. The resulting expected peak input voltage at the LIN/RIN pins is 600 mV, since this is just a voltage divider between the LIN/RIN input resistance (see Table 18, 60 k for this example) and the external resistor. Note that the Peak Input Voltage corresponding 30 Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com Rev. 1.0 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • November 9, 2021 Si4720/21-B20 Input [dBFS] –90 5.18. Audio Dynamic Range Control The Si4720/21 includes digital audio dynamic range control with programmable gain, threshold, attack rate, and release rate. The total dynamic range reduction is set by the gain value and the audio output compression above the threshold is equal to Threshold/(Gain + Threshold) in dB. The gain specified cannot be larger than the absolute value of the threshold. This feature can also be disabled if audio compression is not desired. The audio dynamic range control can be used to reduce the dynamic range of the audio signal, which improves the listening experience on the FM receiver. Audio dynamic range reduction increases the transmit volume by decreasing the peak amplitudes of audio signals and increasing the root mean square content of the audio signal. In other words, it amplifies signals below a threshold by a fixed gain and compresses audio signals above a threshold by the ratio of Threshold/(Gain + Threshold). Figure 24 shows an example transfer function of an audio dynamic range controller with the threshold set at –40 dBFS and a Gain = 20 dB relative to an uncompressed transfer function. –70 –60 –50 –40 –30 –20 Compression 2:1 dB Threshold = –40 dB 0 –10 –10 –20 No Compression –30 –40 M=1 –50 –60 M=1 Gain = 20 dB Note that the TX_LINE_INPUT_LEVEL parameter will affect the high-pass filter characteristics of the accoupling capacitors and the resistance of the audio inputs. The Si4720/21 has a programmable low audio level and high audio level indicators that allows the user to selectively enable and disable the carrier based on the presence of audio content. The TX_ASQ_LEVEL_LOW and TX_ASQ_LEVEL_HIGH parameters set the low level and high level thresholds in dBFS, respectively. The time required for the audio level to be below the low threshold is set with the TX_ASQ_DURATION_LOW parameter, and similarly, the time required for the audio level to be above the high threshold is set with the TX_ASQ_DURATION_HIGH parameter. –80 Output [dBFS] to the chosen LIATTEN[1:0] code still needs to satisfy the condition of being just greater than the attenuated voltage. In this example, a line attenuation code of LIATTEN[1:0] = 11 has a Peak Input Voltage of 636 mV, which is just greater than the expected peak attenuated voltage of 600 mV. Also, the expected peak attenuated voltage is entered into the LILEVEL[9:0] parameter. Again, in this example, 600 mV is entered into LILVEVEL[9:0]. This example shows one possible solution, but many other solutions exist. The optimal solution is to apply the largest possible voltage to the LIN and RIN pins for signal-to-noise considerations; however, practical resistor values may limit the choices. –70 –80 –90 Figure 24. Audio Dynamic Range Transfer Function For input signals below the threshold of –40 dBFS, the output signal is amplified or gained up by 20 dB relative to an uncompressed signal. Audio inputs above the threshold are compressed by a 2 to 1 dB ratio, meaning that every 2 dB increase in audio input level above the threshold results in an audio output increase of 1 dB. In this example, the input dynamic range of 90 dB is reduced to an output dynamic range of 70 dB. Figure 25 shows the time domain characteristics of the audio dynamic range controller. The attack rate sets the speed with which the audio dynamic range controller responds to changes in the input level, and the release rate sets the speed with which the audio dynamic range controller returns to no compression once the audio input level drops below the threshold. Threshold Audio Input Audio Output Attack time Release time Figure 25. Time Domain Characteristics of the Audio Dynamic Range Controller Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 31 Rev. 1.0 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • November 9, 2021 Si4720/21-B20 5.19. Audio Limiter The 4720/21 also includes a digital audio limiter. The audio limiter prevents over-modulation of the FM transmit output by dynamically attenuating peaks in the audio input signal that exceed a programmable threshold. The limiter threshold is set to the programmed audio deviation + ten percent. The threshold ensures that the output signal audio deviation does not exceed the programmed levels, avoiding audible artifacts or distortion in the target FM receiver, and complying with FCC or ETSI regulatory standards. The limiter performs as a peak detector with an attack rate set to one audio sample, resulting in an almost immediate attenuation of the input peak. The recover rate is programmable to the customer’s preference, and is set by default to 5 ms. This is the recommended setting to avoid audible pumping or popping. Refer to “AN332: Universal Programming Guide.” 5.20. Pre-emphasis and De-emphasis Pre-emphasis and de-emphasis is a technique used by FM broadcasters to improve the signal-to-noise ratio of FM receivers by reducing the effects of high-frequency interference and noise. When the FM signal is transmitted, a pre-emphasis filter is applied to accentuate the high audio frequencies. All FM receivers incorporate a de-emphasis filter that attenuates high frequencies to restore a flat frequency response. Two time constants are used in various regions. The preemphasis time constant is programmable to 50 or 75 µs and is set by using the TX_PREEMPHASIS property. 5.21. RDS/RBDS Processor (Si4721 Only) The Si4721 implements an RDS/RBDS* processor for symbol encoding, block synchronization, and error correction. Digital data can be transmitted with the Si4721 RDS/RBDS encoding feature. RDS transmission is supported with three different modes. The first mode is the simplest mode and requires no additional user support except for preloading the desired RDS PI and PTY codes and up to 12 8-byte PS character strings. The Si4721 will transmit the PI code and rotate through the transmission of the PS character strings with no further control required from outside the device. The second mode allows for more complicated transmissions. The PI and PTY codes are written to the device as in mode 1. The remaining blocks (B, C, and D) are written to a 252 byte buffer. This buffer can hold 42 sets of BCD blocks. The Si4721 creates RDS groups by creating block A from the PI code, concatenating blocks BCD from the buffer, and rotating through the buffer. The BCD buffer is circular; so, the pattern is repeated until the buffer is changed. Finally, the third mode allows the outside controller to burst data into the BCD buffer, which emulates a FIFO. The data does not repeat, but, when the buffer is nearly empty, the Si4721 signals the outside device to initiate another data burst. This mode permits the outside device to use any RDS functionality (including open data applications) that it wants. *Note: RDS/RBDS is referred to only as RDS throughout the remainder of this document. 5.22. Tuning The frequency synthesizer uses Skyworks’ proven technology including a completely integrated VCO. The frequency synthesizer generates the quadrature local oscillator signal used to upconvert the low intermediate frequency to RF. The VCO frequency is locked to the reference clock and adjusted with an automatic frequency control (AFC) servo loop during transmission. The tuning frequency can be directly programmed with commands. For example, to tune to 98.1 MHz, the user writes the TX_TUNE_FREQ command with an argument = 9810. The Si4720/21 supports channel spacing of 50, 100, or 200 kHz. 5.23. Reference Clock The Si4720/21 reference clock is programmable, supporting RCLK frequencies from 31.130 kHz to 40 MHz. The RCLK frequency divided by an integer number (the prescaler value) must fall in the range of 31,130 to 34,406 Hz. Therefore, the range of RCLK frequencies is not continuous below frequencies of 311.3 kHz. The default RCLK frequency is 32.768 kHz. Please refer to “AN332: Universal Programming Guide” for using other RCLK frequencies. 5.24. Control Interface A serial port slave interface is provided; this allows an external controller to send commands to the Si4720/21 and receive responses from the device. The serial port can operate in three bus modes: 2-wire mode, SPI mode, or 3-wire mode. The Si4720/21 selects the bus mode by sampling the state of the GPO1 and GPO2/INT pins on the rising edge of RST. The GPO1 pin includes an internal pull-up resistor that is connected while RST is low, and the GPO2/INT pin includes an internal pull-down resistor that is connected while RST is low. Therefore, it is only necessary for the user to actively drive pins that differ from these states. Table 19. Bus Mode Select on Rising Edge of RST Bus Mode GPO1 GPO2/INT 2-Wire 1 0 SPI 1 1 (must drive) 3-Wire 0 (must drive) 0 32 Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com Rev. 1.0 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • November 9, 2021 Si4720/21-B20 After the rising edge of RST, the pins, GPO1 and GPO2/INT, are used as general-purpose output (O) pins as described in Section “5.15. GPO Outputs”. In any bus mode, commands may only be sent after VIO and VDD supplies are applied. 5.24.1. 2-Wire Control Interface Mode When selecting 2-wire mode, the user must ensure that SCLK is high during the rising edge of RST, and stays high until after the first start condition. Also, a start condition must not occur within 300 ns before the rising edge of RST. 2-wire bus mode uses only the SCLK and SDIO pins for signaling. A transaction begins with the START condition, which occurs when SDIO falls while SCLK is high. Next, the user drives an 8-bit control word serially on SDIO, which is captured by the device on rising edges of SCLK. The control word consists of a seven bit device address followed by a read/write bit (read = 1, write = 0). The Si4720/21 acknowledges the control word by driving SDIO low on the next falling edge of SCLK. Although the Si4720/21 responds to only a single device address, this address can be changed with the SEN pin (note that the SEN pin is not used for signaling in 2-wire mode). When SEN = 0, the seven-bit device address is 0010001. When SEN = 1, the address is 1100011. For write operations, the user then sends an eight bit data byte on SDIO, which is captured by the device on rising edges of SCLK. The Si4720/21 acknowledges each data byte by driving SDIO low for one cycle, on the next falling edge of SCLK. The user may write up to eight data bytes in a single two-wire transaction. The first byte is a command, and the next seven bytes are arguments. For read operations, after the Si4720/21 has acknowledged the control byte, it drives an eight-bit data byte on SDIO, changing the state of SDIO on the falling edge of SCLK. The user acknowledges each data byte by driving SDIO low for one cycle, on the next falling edge of SCLK. If a data byte is not acknowledged, the transaction ends. The user may read up to 16 data bytes in a single two-wire transaction. These bytes contain the response data from the Si4720/21. A 2-wire transaction ends with the STOP condition, which occurs when SDIO rises while SCLK is high. For details on timing specifications and diagrams, refer to: 5, “2-Wire Control Interface Characteristics1,2,3,” on page 7, Table Figure 2, “2-Wire Control Interface Read and Write Timing Parameters,” on page 8, and Figure 3, “2-Wire Control Interface Read and Write Timing Diagram,” on page 8. 5.24.2. SPI Control Interface Mode When selecting SPI mode, the user must ensure that a rising edge of SCLK does not occur within 300 ns before the rising edge of RST. SPI bus mode uses the SCLK, SDIO, and SEN pins for read/write operations. For reads, the user can choose to receive data from the device on either SDIO or GPO1. A transaction begins when the user drives SEN low. The user then pulses SCLK eight times while driving an 8-bit control byte (MSB first) serially on SDIO. The device captures the data on rising edges of SCLK. The control byte must have one of these values: 0x48 = write eight command/argument bytes (user drives write data on SDIO) 0x80 = read status byte (device drives read data on SDIO) 0xA0 = read status byte (device drives read data on GPO1) 0xC0 = read 16 response bytes (device drives read data on SDIO) 0xE0 = read 16 response bytes (device drives read data on GPO1) When writing a command, after the control byte has been written, the user must drive exactly eight data bytes (a command byte and seven argument bytes) on SDIO. The data will be captured by the device on the rising edges of SCLK. After all eight data bytes have been written, the user raises SEN after the last falling edge of SCLK to end the transaction. In any bus mode, before sending a command or reading a response, the user must first read the status byte to ensure that the device is ready (CTS bit is high). In SPI mode, this is done by sending control byte 0x80 or 0xA0, followed by reading a single byte on SDIO or GPO1. The Si4720/21 changes the state of SDIO or GPO1 after the falling edges of SCLK. Data should be captured by the user on the rising edges of SCLK. After the status byte has been read, the user raises SEN after the last falling edge of SCLK to end the transaction. When reading a response, the user must read exactly 16 data bytes after sending the control byte. It is recommended that the user keep SEN low until all bytes have transferred. However, it will not disrupt the protocol if SEN temporarily goes high at any time, as long as the user does not change the state of SCLK while SEN is high. After 16 bytes have been read, the user raises SEN after the last falling edge of SCLK to end the transaction. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 33 Rev. 1.0 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • November 9, 2021 Si4720/21-B20 At the end of any SPI transaction, the user must drive SEN high after the final falling edge of SCLK. At any time during a transaction, if SEN is sampled high by the device on a rising edge of SCLK, the transaction will be aborted. When SEN is high, SCLK may toggle without affecting the device. For details on timing specifications and diagrams, refer to Figure 6 and Figure 7 on page 10. 5.24.3. 3-Wire Control Interface Mode When selecting 3-wire mode, the user must ensure that a rising edge of SCLK does not occur within 300 ns before the rising edge of RST. 3-wire bus mode uses the SCLK, SDIO and SEN pins. A transaction begins when the system controller drives SEN low. Next, the system controller drives a 9-bit control word on SDIO, which is captured by the device on rising edges of SCLK. The control word is comprised of a three bit chip address (A7:A5 = 101b), a read/write bit (write = 0, read = 1), the chip address (A4 = 0), and a four bit register address (A3:A0). For write operations, the control word is followed by a 16-bit data word, which is captured by the device on rising edges of SCLK. For read operations, the control word is followed by a delay of one-half SCLK cycle for bus turnaround. Next, the Si4720/21 drives the 16-bit read data word serially on SDIO, changing the state of SDIO on each rising edge of SCLK. A transaction ends when the user sets SEN high, then pulses SCLK high and low one final time. SCLK may either stop or continue to toggle while SEN is high. In 3-wire mode, commands are sent by first writing each argument to register(s) 0xA1–0xA3, then writing the command word to register 0xA0. A response is retrieved by reading registers 0xA8–0xAF. For details on timing specifications and diagrams, refer to Table 6, “3-Wire Control Interface Characteristics,” on page 9, Figure 4, “3-Wire Control Interface Write Timing Parameters,” on page 9, and Figure 5, “3-Wire Control Interface Read Timing Parameters,” on page 9. 5.25. GPO Outputs The Si4720/21 provides three general-purpose output pins. The GPO pins can be configured to output a constant low, constant high, or high-Z. The GPO pins are multiplexed with the bus mode pins or DCLK depending on the application schematic of the device. GPO2/INT can be configured to provide interrupts for seek and tune complete, receive signal quality, and RDS. 5.26. Reset, Powerup, and Powerdown Setting the RST pin low will disable analog and digital circuitry, reset the registers to their default settings, and disable the bus. Setting the RST pin high will bring the device out of reset and place it in powerdown mode. A powerdown mode is available to reduce power consumption when the part is idle. Putting the device in powerdown mode will disable analog and digital circuitry and keep the bus active. For more information concerning Reset, Powerup, Powerdown, and Initialization, refer to “AN332: Universal Programming Guide.” 5.27. Programming with Commands To ease development time and offer maximum customization, the Si4720/21 provides a simple yet powerful software interface to program the transmitter. The device is programmed using commands, arguments, properties, and responses. To perform an action, the user writes a command byte and associated arguments causing the chip to execute the given command. Commands control actions, such as powering up the device, shutting down the device, or tuning to a station. Arguments are specific to a given command and are used to modify the command. For example, after the TX_TUNE_FREQ command, arguments are required to set the tune frequency. A complete list of commands is available in Table 17, “Si471x Command Summary,” on page 30. Properties are a special command argument used to modify the default chip operation and are generally configured immediately after powerup. Examples of properties are TX_PREEMPHASIS and GPO_CONFIGURE. A complete list of properties is available in Table 21, “Si472x Property Summary,” on page 36. Responses provide the user information and are echoed after a command and associated arguments are issued. At a minimum, all commands provide a one-byte status update indicating interrupt and clear-to-send status information. For a detailed description of using the commands and properties of the Si4720/21, see “AN332: Universal Programming Guide.” 34 Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com Rev. 1.0 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • November 9, 2021 Si4720/21-B20 6. Commands and Properties Table 20. Si472x Command Summary Cmd Name Description Transmit Commands Power up device and mode selection. Modes include FM transmit and analog/digital audio interface configuration. 0x01 POWER_UP 0x10 GET_REV 0x11 POWER_DOWN Power down device. 0x12 SET_PROPERTY Sets the value of a property. 0x13 GET_PROPERTY Retrieves a property’s value. 0x14 GET_INT_STATUS Read interrupt status bits. 0x15 PATCH_ARGS Reserved command used for patch file downloads. 0x16 PATCH_DATA Reserved command used for patch file downloads. 0x30 TX_TUNE_FREQ 0x31 TX_TUNE_POWER Sets the output power level and tunes the antenna capacitor. 0x32 TX_TUNE_MEASURE Measure the received noise level at the specified frequency. 0x33 TX_TUNE_STATUS 0x34 TX_ASQ_STATUS 0x35 TX_RDS_BUFF 0x36 TX_RDS_PS 0x80 GPIO_CTL Configures GPO1, 2, and 3 as output or Hi-Z. 0x81 GPIO_SET Sets GPO1, 2, and 3 output level (low or high). Returns revision information on the device. Tunes to given transmit frequency. Queries the status of a previously sent TX Tune Freq, TX Tune Power, or TX Tune Measure command. Queries the TX status and input audio signal metrics. Queries the status of the RDS Group Buffer and loads new data into buffer. Set up default PS strings. Receive Commands Power up device and mode selection. 0x01 POWER_UP 0x10 GET_REV 0x11 POWER_DOWN Power down device. 0x12 SET_PROPERTY Sets the value of a property. 0x13 GET_PROPERTY Retrieves a property’s value. 0x14 GET_INT_STATUS Reads interrupt status bits. 0x15 PATCH_ARGS Reserved command used for patch file downloads. 0x16 PATCH_DATA Reserved command used for patch file downloads. 0x20 FM_TUNE_FREQ Selects the FM tuning frequency. 0x21 FM_SEEK_START Begins searching for a valid frequency. Returns revision information on the device. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 35 Rev. 1.0 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • November 9, 2021 Si4720/21-B20 Table 20. Si472x Command Summary (Continued) 0x22 FM_TUNE_STATUS Queries the status of previous FM_TUNE_FREQ or FM_SEEK_START command. 0x23 FM_RSQ_STATUS Queries the status of the Received Signal Quality (RSQ) of the current channel. 0x24 FM_RDS_STATUS Returns RDS information for current channel and reads an entry from RDS FIFO (Si4721 only). 0x27 FM_AGC_STATUS Queries the current AGC settings 0x28 FM_AGC_OVERRIDE 0x80 GPIO_CTL Configures GPO1, 2, and 3 as output or Hi-Z. 0x81 GPIO_SET Sets GPO1, 2, and 3 output level (low or high). Override AGC setting by disabling and forcing it to a fixed value Table 21. Si472x Property Summary Prop Name Description Default Transmit Properties Enables interrupt sources. 0x0000 Configures the digital input format. 0x0000 Configures the digital input sample rate in 1 Hz steps. Default is 0. 0x0000 Sets frequency of the reference clock in Hz. The range is 31130 to 34406 Hz, or 0 to disable the AFC. Default is 32768 Hz. 0x8000 Sets the prescaler value for the reference clock. 0x0001 Enable transmit multiplex signal components. Default has pilot and L-R enabled. 0x0003 TX_AUDIO_DEVIATION Configures audio frequency deviation level. Units are in 10 Hz increments. Default is 6825 (68.25 kHz). 0x1AA9 0x2102 TX_PILOT_DEVIATION Configures pilot tone frequency deviation level. Units are in 10 Hz increments. Default is 675 (6.75 kHz) 0x02A3 0x2103 TX_RDS_DEVIATION Si4721 Only. Configures the RDS/RBDS frequency deviation level. Units are in 10 Hz increments. Default is 2 kHz. 0x00C8 0x2104 TX_LINE_INPUT_LEVEL Configures maximum analog line input level to the LIN/RIN pins to reach the maximum deviation level programmed into the audio deviation property TX Audio Deviation. Default is 636 mVPK. 0x327C 0x2105 TX_LINE_INPUT_MUTE Sets line input mute. L and R inputs may be independently muted. Default is not muted. 0x0000 0x2106 TX_PREEMPHASIS Configures pre-emphasis time constant. Default is 0 (75 µS). 0x0000 0x2107 TX_PILOT_FREQUENCY Configures the frequency of the stereo pilot. Default is 19000 Hz. 0x4A38 0x0001 GPO_IEN 0x0101 DIGITAL_INPUT _FORMAT 0x0103 DIGITAL_INPUT _SAMPLE_RATE 0x0201 REFCLK_FREQ 0x0202 REFCLK_PRESCALE 0x2100 TX_COMPONENT_ENABLE 0x2101 36 Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com Rev. 1.0 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • November 9, 2021 Si4720/21-B20 Table 21. Si472x Property Summary (Continued) Prop Name 0x2200 TX_ACOMP_ENABLE 0x2201 Description Default Enables audio dynamic range control and limiter. Default is 2 (limiter is enabled, audio dynamic range control is disabled). 0x0002 TX_ACOMP_THRESHOLD Sets the threshold level for audio dynamic range control. Default is –40 dB. 0xFFD8 0x2202 TX_ACOMP_ATTACK_TIME Sets the attack time for audio dynamic range control. Default is 0 (0.5 ms). 0x0000 0x2203 TX_ACOMP_RELEASE_TIME Sets the release time for audio dynamic range control. Default is 4 (1000 ms). 0x0004 0x2204 TX_ACOMP_GAIN Sets the gain for audio dynamic range control. Default is 15 dB. 0x000F 0x2205 TX_LIMITER_RELEASE_TIME Sets the limiter release time. Default is 102 (5.01 ms) 0x0066 0x2300 TX_ASQ_INTERRUPT_SOURCE Configures measurements related to signal quality metrics. Default is none selected. 0x0000 0x2301 TX_ASQ_LEVEL_LOW Configures low audio input level detection threshold. This threshold can be used to detect silence on the incoming audio. 0x0000 0x2302 TX_ASQ_DURATION_LOW Configures the duration which the input audio level must be below the low threshold in order to detect a low audio condition. 0x0000 0x2303 TX_ASQ_LEVEL_HIGH Configures high audio input level detection threshold. This threshold can be used to detect activity on the incoming audio. 0x0000 0x2304 TX_ASQ_DURATION_HIGH Configures the duration which the input audio level must be above the high threshold in order to detect a high audio condition. 0x0000 0x2C00 TX_RDS_INTERRUPT_SOURCE Si4721 Only. Configure RDS interrupt sources. Default is none selected. 0x0000 0x2C01 TX_RDS_PI Si4721 Only. Sets transmit RDS program identifier. 0x40A7 0x2C02 TX_RDS_PS_MIX Si4721 Only. Configures mix of RDS PS Group with RDS Group Buffer. 0x0003 0x2C03 TX_RDS_PS_MISC Si4721 Only. Miscellaneous bits to transmit along with RDS_PS Groups. 0x1008 0x2C04 TX_RDS_PS_REPEAT_COUNT Si4721 Only. Number of times to repeat transmission of a PS message before transmitting the next PS message. 0x0003 0x2C05 TX_RDS_PS_MESSAGE_COUNT Si4721 Only. Number of PS messages in use. 0x0001 0x2C06 TX_RDS_PS_AF Si4721 Only. RDS Program Service Alternate Frequency. This provides the ability to inform the receiver of a single alternate frequency using AF Method A coding and is transmitted along with the RDS_PS Groups. 0xE0E0 0x2C07 TX_RDS_FIFO_SIZE Si4721 Only. Number of blocks reserved for the FIFO. Note that the value written must be one larger than the desired FIFO size. 0x0000 Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 37 Rev. 1.0 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • November 9, 2021 Si4720/21-B20 Table 21. Si472x Property Summary (Continued) Prop Name Description Default Receive Properties Enables interrupt sources. 0x0000 DIGITAL_OUTPUT_ FORMAT Configure digital audio outputs (Si4721 only) 0x0000 0x0104 DIGITAL_OUTPUT_ SAMPLE_RATE Configure digital audio output sample rate (Si4721 only) 0x0000 0x0201 REFCLK_FREQ Sets frequency of reference clock in Hz. The range is 31130 to 34406 Hz, or 0 to disable the AFC. Default is 32768 Hz. 0x8000 0x0202 REFCLK_PRESCALE Sets the prescaler value for RCLK input. 0x0001 0x1100 FM_DEEMPHASIS Sets deemphasis time constant. Default is 75 µs. 0x0002 0x0001 GPO_IEN 0x0102 0x1105 FM_BLEND_STEREO_THRESHOLD Sets RSSI threshold for stereo blend (Full stereo above 0x0031 threshold, blend below threshold). To force stereo set this to 0. To force mono set this to 127. Default value is 49 dBµV. 0x1106 FM_BLEND_MONO_ THRESHOLD Sets RSSI threshold for mono blend (Full mono below threshold, blend above threshold). To force stereo set this to 0. To force mono set this to 127. Default value is 30 dBµV. 0x001E 0x1107 FM_ANTENNA_INPUT Selects the antenna type and the pin to which it is connected. (Si4721 only). 0x0000 0x1108 FM_MAX_TUNE_ ERROR Sets the maximum freq error allowed before setting the AFC rail (AFCRL) indicator. Default value is 30 kHz. 0x001E 0x1200 FM_RSQ_INT_ SOURCE Configures interrupt related to Received Signal Quality metrics. 0x0000 0x1201 FM_RSQ_SNR_HI_ THRESHOLD Sets high threshold for SNR interrupt. 0x007F 0x1202 FM_RSQ_SNR_LO_ THRESHOLD Sets low threshold for SNR interrupt. 0x0000 0x1203 FM_RSQ_RSSI_HI_ THRESHOLD Sets high threshold for RSSI interrupt. 0x1204 FM_RSQ_RSSI_LO_ THRESHOLD Sets low threshold for RSSI interrupt. 0x0000 0x1207 FM_RSQ_BLEND_ THRESHOLD Sets the blend threshold for blend interrupt when boundary is crossed. 0x0081 0x1300 FM_SOFT_MUTE_RATE Sets the attack and decay rates when entering and leaving soft mute. 0x0040 0x1302 FM_SOFT_MUTE_ MAX_ATTENUATION Sets maximum attenuation during soft mute (dB). Set to 0 to disable soft mute. Default is 16 dB. 0x0010 0x1303 FM_SOFT_MUTE_ SNR_THRESHOLD Sets SNR threshold to engage soft mute. Default is 4 dB. 0x0004 0x1400 FM_SEEK_BAND_ BOTTOM Sets the bottom of the FM band for seek. Default is 8750 (87.5 MHz). 0x222E 0x007F 38 Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com Rev. 1.0 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • November 9, 2021 Si4720/21-B20 Table 21. Si472x Property Summary (Continued) Prop Name 0x1401 FM_SEEK_BAND_TOP 0x1402 Description Default Sets the top of the FM band for seek. Default is 10790 (107.9 MHz). 0x2A26 FM_SEEK_FREQ_ SPACING Selects frequency spacing for FM seek. Default value is 10 (100 kHz). 0x000A 0x1403 FM_SEEK_TUNE_ SNR_THRESHOLD Sets the SNR threshold for a valid FM Seek/Tune. Default value is 3 dB. 0x0003 0x1404 FM_SEEK_TUNE_ RSSI_TRESHOLD Sets the RSSI threshold for a valid FM Seek/Tune. Default value is 20 dBµV. 0x0014 0x1500 RDS_INT_SOURCE Configures RDS interrupt behavior (Si4721 only). 0x0000 0x1501 RDS_INT_FIFO_ COUNT Sets the minimum number of RDS groups stored in the receive FIFO required before RDSRECV is set (Si4721 only). 0x0000 0x1502 RDS_CONFIG Configures RDS setting (Si4721 only). 0x0000 0x4000 RX_VOLUME Sets the output volume. 0x003F 0x4001 RX_HARD_MUTE Mutes the audio output. L and R audio outputs may be muted independently. 0x0000 Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 39 Rev. 1.0 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • November 9, 2021 Si4720/21-B20 GPO2/INT GPO3/DCLK LIN/DFS 1 GPO1 NC NC 7. Pin Descriptions: Si4720/21-GM 20 19 18 17 16 FMI 2 15 RIN/DOUT RFGND 3 14 LOUT/DFS GND PAD TXO 4 13 ROUT/DIN 6 7 8 9 10 SCLK SDIO RCLK VIO 12 GND SEN RST 5 11 VDD Pin Number(s) Name Description 1, 20 NC No connect. Leave floating. 2 FMI FM RF input. 3 RFGND 4 TXO FM transmit output connection to transmit antenna. 5 RST Device reset (active low) input. 6 SEN Serial enable input (active low). 7 SCLK Serial clock input. 8 SDIO Serial data input/output. 9 RCLK External reference oscillator input. 10 VIO I/O supply voltage. 11 VDD Supply voltage. May be connected directly to battery. 13 ROUT/DIN Right audio line output—digital input data. 14 LOUT/DFS Left audio line output—digital frame synchronization. 15 RIN/DOUT Right audio line input—digital output data. 16 LIN/DFS 17 GPO3/DCLK 18 GPO2/INT 19 GPO1 General purpose output. 12, GND PAD GND Ground. Connect to ground plane on PCB. RF ground. Connect to ground plane on PCB. Left audio line input—digital frame synchronization. General purpose output—digital bit synchronous clock. General purpose output—interrupt request. 40 Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com Rev. 1.0 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • November 9, 2021 Si4720/21-B20 8. Ordering Guide Part Number* Description Package Type Operating Temperature Si4720-B20-GM Broadcast FM Radio Transceiver for Portable Applications QFN Pb-free –20 to 85 °C Si4721-B20-GM Broadcast FM Radio Transceiver for Portable Applications with RDS/RBDS Encoder/Decoder QFN Pb-free –20 to 85 °C *Note: Add an “(R)” at the end of the device part number to denote tape and reel option; 2500 quantity per reel. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 41 Rev. 1.0 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • November 9, 2021 Si4720/21-B20 9. Package Markings (Top Marks) 9.1. Top Mark Explanation Mark Method: YAG Laser Line 1 Marking: Part Number 20 = Si4720; 21 = Si4721 Firmware Revision 20 = Firmware Revision 2.0 Die Revision B = Revision B Die TTT = Internal Code Internal tracking code. Line 2 Marking: Line 3 Marking: Circle = 0.5 mm Diameter Pin 1 Identifier (Bottom-Left Justified) Y = Year WW = ‘Workweek Assigned by the Assembly House. Corresponds to the last significant digit of the year and workweek of the mold date. 9.2. Si4720/21 Top Mark 9.3. Si4721 Top Mark 42 Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com Rev. 1.0 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • November 9, 2021 Si4720/21-B20 10. Package Outline: Si4720/21-GM Figure 26 illustrates the package details for the Si4720. Table 22 lists the values for the dimensions shown in the illustration. Figure 26. 20-Pin Quad Flat No-Lead (QFN) Table 22. Package Dimensions Symbol Millimeters Symbol Millimeters Min Nom Max A 0.50 0.55 0.60 f A1 0.00 0.02 0.05 L 0.35 0.40 0.45 b 0.20 0.25 0.30 L1 0.00 — 0.10 c 0.27 0.32 0.37 aaa — — 0.05 bbb — — 0.05 ccc — — 0.08 D D2 3.00 BSC 1.65 1.70 1.75 Min Nom Max 2.53 BSC e 0.50 BSC ddd — — 0.10 E 3.00 BSC eee — — 0.10 E2 1.65 1.70 1.75 Notes: 1. All dimensions are shown in millimeters (mm) unless otherwise noted. 2. Dimensioning and tolerancing per ANSI Y14.5M-1994. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 43 Rev. 1.0 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • November 9, 2021 Si4720/21-B20 11. PCB Land Pattern: Si4720/21-GM Figure 27 illustrates the PCB land pattern details for the Si4720-GM. Table 23 lists the values for the dimensions shown in the illustration. Figure 27. PCB Land Pattern 44 Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com Rev. 1.0 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • November 9, 2021 Si4720/21-B20 Table 23. PCB Land Pattern Dimensions Symbol Millimeters Min D D2 Symbol Max 2.71 REF 1.60 1.80 Min Max GE 2.10 — W — 0.34 — 0.28 e 0.50 BSC X E 2.71 REF Y E2 1.60 f GD 1.80 2.53 BSC 2.10 Millimeters 0.61 REF ZE — 3.31 ZD — 3.31 — Notes: General 1. All dimensions shown are in millimeters (mm) unless otherwise noted. 2. Dimensioning and tolerancing is per the ANSI Y14.5M-1994 specification. 3. This land pattern design is based on IPC-SM-782 guidelines. 4. All dimensions shown are at Maximum Material Condition (MMC). Least Material Condition (LMC) is calculated based on a fabrication allowance of 0.05 mm. Note: Solder Mask Design 1. All metal pads are to be non-solder-mask-defined (NSMD). Clearance between the solder mask and the metal pad is to be 60 mm minimum, all the way around the pad. Notes: Stencil Design 1. A stainless steel, laser-cut and electro-polished stencil with trapezoidal walls should be used to assure good solder paste release. 2. The stencil thickness should be 0.125 mm (5 mils). 3. The ratio of stencil aperture to land pad size should be 1:1 for the perimeter pads. 4. A 1.45 x 1.45 mm square aperture should be used for the center pad. This provides approximately 70% solder paste coverage on the pad, which is optimum to assure correct component standoff. Notes: Card Assembly 1. A No-Clean, Type-3 solder paste is recommended. 2. The recommended card reflow profile is per the JEDEC/IPC J-STD-020C specification for small body components. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 45 Rev. 1.0 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • November 9, 2021 Si4720/21-B20 12. Additional Reference Resources        Si47xx Evaluation Board User’s Guide AN307: Si4712/13/20/21 Receive Power Scan AN332: Universal Programming Guide AN341: Si4720/21 Evalution Board Quick Start Guide AN383: Universal Antenna Selection and Layout Guidelines AN388: Universal Evaluation Board Test Procedure Si4720/21 Customer Support Site: www.skyworksinc.com/en/Support 46 Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com Rev. 1.0 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • November 9, 2021 Connecting Everyone and Everything, All the Time Portfolio Quality Support & Resources www.skyworksinc.com www.skyworksinc.com/quality www.skyworksinc.com/support Copyright © 2021 Skyworks Solutions, Inc. All Rights Reserved. Information in this document is provided in connection with Skyworks Solutions, Inc. (“Skyworks”) products or services. These materials, including the information contained herein, are provided by Skyworks as a service to its customers and may be used for informational purposes only by the customer. Skyworks assumes no responsibility for errors or omissions in these materials or the information contained herein. Skyworks may change its documentation, products, services, specifications or product descriptions at any time, without notice. Skyworks makes no commitment to update the materials or information and shall have no responsibility whatsoever for conflicts, incompatibilities, or other difficulties arising from any future changes. No license, whether express, implied, by estoppel or otherwise, is granted to any intellectual property rights by this document. Skyworks assumes no liability for any materials, products or information provided hereunder, including the sale, distribution, reproduction or use of Skyworks products, information or materials, except as may be provided in Skyworks’ Terms and Conditions of Sale. THE MATERIALS, PRODUCTS AND INFORMATION ARE PROVIDED “AS IS” WITHOUT WARRANTY OF ANY KIND, WHETHER EXPRESS, IMPLIED, STATUTORY, OR OTHERWISE, INCLUDING FITNESS FOR A PARTICULAR PURPOSE OR USE, MERCHANTABILITY, PERFORMANCE, QUALITY OR NON-INFRINGEMENT OF ANY INTELLECTUAL PROPERTY RIGHT; ALL SUCH WARRANTIES ARE HEREBY EXPRESSLY DISCLAIMED. SKYWORKS DOES NOT WARRANT THE ACCURACY OR COMPLETENESS OF THE INFORMATION, TEXT, GRAPHICS OR OTHER ITEMS CONTAINED WITHIN THESE MATERIALS. SKYWORKS SHALL NOT BE LIABLE FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO ANY SPECIAL, INDIRECT, INCIDENTAL, STATUTORY, OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION, LOST REVENUES OR LOST PROFITS THAT MAY RESULT FROM THE USE OF THE MATERIALS OR INFORMATION, WHETHER OR NOT THE RECIPIENT OF MATERIALS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Skyworks products are not intended for use in medical, lifesaving or life-sustaining applications, or other equipment in which the failure of the Skyworks products could lead to personal injury, death, physical or environmental damage. Skyworks customers using or selling Skyworks products for use in such applications do so at their own risk and agree to fully indemnify Skyworks for any damages resulting from such improper use or sale. Customers are responsible for their products and applications using Skyworks products, which may deviate from published specifications as a result of design defects, errors, or operation of products outside of published parameters or design specifications. Customers should include design and operating safeguards to minimize these and other risks. Skyworks assumes no liability for applications assistance, customer product design, or damage to any equipment resulting from the use of Skyworks products outside of Skyworks’ published specifications or parameters. Skyworks, the Skyworks symbol, Sky5®, SkyOne®, SkyBlue™, Skyworks Green™, Clockbuilder®, DSPLL®, ISOmodem®, ProSLIC®, and SiPHY® are trademarks or registered trademarks of Skyworks Solutions, Inc. or its subsidiaries in the United States and other countries. Third-party brands and names are for identification purposes only and are the property of their respective owners. Additional information, including relevant terms and conditions, posted at www.skyworksinc.com, are incorporated by reference. Skyworks Solutions, Inc. | Nasdaq: SWKS | sales@skyworksinc.com | www.skyworksinc.com USA: 781-376-3000 | Asia: 886-2-2735 0399 | Europe: 33 (0)1 43548540 |