Si4827-DEMO
Si4827 DEMO BOARD USER’S GUIDE
1. Features
ATDD
(analog tune and digital display) FM/AM/SW radio
Worldwide
FM band support from 64 MHz to 109 MHz with 5 default sub-bands:
FM1
87—108 MHz (Demo Board Default)
86.5—109 MHz
FM3 87.3—108.25 MHz
FM4 76—90 MHz
FM5 64—87 MHz (Demo Board Default)
FM2
Worldwide AM
band support from 504 to 1750 kHz with 5 default sub-bands
AM1
520—1710 kHz (Demo Board Default)
522—1620 kHz (Demo Board Default)
AM3 504—1665 kHz
AM4 520—1730 kHz
AM5 510—1750 kHz
AM2
Worldwide
SW band support from 2.3 to 28.5 MHz with 16 default sub-bands:
SW1
5.6—6.4 MHz (DEMO Board Default)
5.95—6.2 MHz
SW3 6.8—7.6 MHz (DEMO Board Default)
SW4 7.1—7.6 MHz
SW5 9.2—10 MHz (DEMO Board Default)
SW6 9.2—9.9 MHz
SW7 11.45—12.25 MHz (DEMO Board Default)
SW8 11.6—12.2 MHz
SW9 13.4—14.2 MHz (DEMO Board Default)
SW10 13.57—13.87 MHz
SW11 15—15.9 MHz (DEMO Board Default)
SW12 15.1—15.8 MHz
SW13 17.1—18 MHz (DEMO Board Default)
SW14 17.48—17.9 MHz
SW15 21.2—22 MHz (DEMO Board Default)
SW16 21.45—21.85 MHz
SW2
Support
wider FM/SW band range.
Twelve
positions slide switch or one push button for selecting different band according to the target
application.
Two AAA battery
Economical
potentiometer for frequency tuning replaces more expensive variable capacitor (PVC).
Potentiometer
FM
operations with working voltage down to 2.0 V
and/or push button volume control
50 µs or 75 µs (default) de-emphasis
9-level
Bass/Treble via push button control for FM
7-level
Bass/Treble via push button control for AM/ SW
FM/AM/SW
band indicator and frequency display in LCD
2×4
matrix keypad
The
frequency range of each band, De-emphasis and AM channel space can be re-configured by host MCU.
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
Rev. 0.1 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • October 2, 2021
Si4827-DEMO
2. Overview
This manual describes the operation of the Skyworks Solutions Si4827-DEMO board Rev1.1, January 22, 2013.
The Skyworks Solutions Si4827-DEMO board is designed with the 16-pin SOIC packaged Si4827 chip, the
revolutionary single chip AM/FM/SW receiver that integrates everything from antenna input to audio output and
allows use of common and economical potentiometers to do the frequency tuning. It provides a complete portable
analog tune analog display AM/FM/SW radio design. The LCD displays the tuning information. The Si4827-DEMO
is designed with 1-layer PCB, allowing the lowest cost without sacrificing the RF performance. The DEMO board
works with two AAA batteries and working voltage down to 2.0 V.
3. Description
Figure 1 and Figure 2 shows the physical layout of the board with key components indicated.
Figure 1. Si4827-DEMO Board Top Side in Time Mode
Figure 2. Si4827-DEMO Board Bottom Side
2
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
Rev. 0.1 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • October 2, 2021
Si4827-DEMO
Power:
BAT1: 2 cells AAA battery compartment
Audio Connectors:
J5: Mono audio headphone output
Antenna Selections:
AM antenna: Ferrite stick antenna for AM
J6: SMA connector for AM conductive test
S11: AM antenna selector
1
2
3
1-2: SMA for AM Conductive Test (J6)
2-3: AM ferrite antenna
J1: BNC connector for FM/ SW conductive test or FM whip
S12: FM antenna selector
3
2
1-2: FMHP ANT (J5)
2-3: FM BNC (J1)
1
Radio Band Selection:
The DEMO board provides two methods for selecting the radio band: one is to use the slide switch S2; the other is
to use the push button, POWER/BAND. S14 determines which method is in use.
S14:
3
2
2-3: Use slide switch to select band
1-2: Use push button to select band
1
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
3
Rev. 0.1 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • October 2, 2021
Si4827-DEMO
Main Components:
U1: Skyworks Solutions Si4827 AM/FM/SW ATDD receiver
U2: Audio amplifier
U3: MCU
LCD: The digital display for tuning information
Control Interface:
VR1: Frequency tuning wheel.
VR2: Volume control wheel
S3~S10: The keypad for human interface
S2: Band switch for FM, AM, and SW
1
2
3
4
5
6
7
8
9
10
11
12
Band definition for the slide switch is as below:
1: FM1 (W 64–108 MHz) (N 87–108 MHz), De-emphasis = 75 µs, ST indication = 6 dB separation@20 dBµV
2: FM5 (W 76–108 MHz) (N 64–87 MHz), De-emphasis = 75 µs, ST indication = 6 dB separation@20 dBµV
3: AM1 (520–1710 kHz), 10 kHz spacing
4: AM2 (522–1620 kHz), 9 kHz spacing
5:SW1 (W 3.2–7.6 MHz) (N 5.6–6.4 MHz)
6:SW3 (W 3.2–10.0 MHz) (N 6.8–7.6 MHz)
7:SW5 (W 5.9–18.0 MHz) (N 9.2–10.0 MHz)
8:SW7 (W 7.0–16.0 MHz) (N 11.45–12.25 MHz)
9:SW9 (W 7.0–23.0 MHz) (N 13.4–14.2 MHz)
10:SW11 (W 9.0–22.0 MHz) (N 15–15.9 MHz)
11:SW13 (W 9.5–18.0 MHz) (N 17.1–18 MHz)
12:SW15 (W 10.0–22.0 MHz) (N 21.2–22 MHz)
Note: N = SW Narrow-band, W = SW Wideband
4
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
Rev. 0.1 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • October 2, 2021
Si4827-DEMO
Human Interface:
There are 8 keys for controlling the DEMO board as shown below.
TREBLE/AL
BASS/TMR
DE/SPC
POWER/BAND
SETTING
W/N BAND
DOWN/VOL-
UP/VOL+
Each key can have a different function under each operating condition:
Time
mode: Radio function is disabled. LCD displays time. Buttons can be used to set time, alarm, etc.
FM/AM/SW
radio mode: Tuner IC works in power up mode. Radio function is enabled. LCD displays the
radio station parameters. Buttons are used to adjust radio settings.
The functions of the buttons are summarized in Table 1.
The FM/AM/SW radio parameters which can be configured are listed below in Table 2.
Table 1. Key Function Description
Button/Mode
Time Mode
Tuner Off
POWER/BAND Hold Time:
< 1s
Hold Time:
> 1s
DE/SPC
FM/AM/SW Radio Mode
Tuner On
None
Change between FM, AM, and SW
(2 FM band, 2 AM band, and 8 SW bands)
Enable radio
Disable radio function and enter time mode.
(Radio parameters will be saved to MCU)
None
FM mode: Change De-emphasis, between
50 µs and 75 µs.
AM mode: Change channel space,
between 9 kHz and 10 kHz.
BASS/TMR
Enter or quit time setting menu.
Decrease Bass/Treble level by 1 step.
TREBLE/AL
Enable or disable the alarm function;
enter or quit alarm setting menu.
Increase Bass/Treble level by 1 step.
Hold Time:
< 1s
In setting menu, change the current
time/alarm parameter by one unit per
each press.
In radio setting menu, change the current
parameter by one unit per each press.
In radio working mode, increase volume
1 step per each press.
Hold Time:
> 1s
In setting menu, change the current
time/alarm parameter automatically.
In radio setting menu, change the current
parameter automatically.
In radio working mode, increase volume
level automatically until to maximum.
UP/VOL+
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
5
Rev. 0.1 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • October 2, 2021
Si4827-DEMO
Table 1. Key Function Description
Button/Mode
Time Mode
Tuner Off
DOWN/VOL-
6
Tuner On
Hold Time:
< 1s
In setting menu, change the current
time/alarm parameter by one unit per
each press.
In radio setting menu, change the current
parameter by one unit per each press.
In radio working mode, decrease volume
1 step per each press.
Hold Time:
> 1s
In setting menu, change the current
time/alarm parameter automatically.
In radio setting menu, change the current
parameter automatically.
In radio working mode, decrease volume
level automatically until to minimum.
None
FM/SW mode: change band range between
wideband and narrow-band.
Hold Time:
< 1s
None
In radio setting menu, change the current
item by one step per each press
Hold Time:
> 1s
None
Quickly return to FM working mode.
W/N BAND
SETTING
FM/AM/SW Radio Mode
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
Rev. 0.1 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • October 2, 2021
Si4827-DEMO
Table 2. Radio Configuration Parameters
FM Parameter
AM Parameter
SW Parameter
Bass/Treble: 0-8
Default: 4
Bass/Treble: 1-7
Default: 3
Bass/Treble: 1-7
Default: 3
Digital volume: 0-63
Default: 63
Digital volume: 0-63
Default: 63
Digital volume: 0-63
Default: 63
Band top: max 109 MHz
Default: 108/108 MHz for
wide band FM1/FM2
Band top: max 1750 kHz
Default: 1710 kHz
Band top: max 28.5 MHz
Default:
7.6/10.0/18.0/16.0/23.0/22.0/18.0/22.0 MHz for
wideband SW1 to SW8 respectively.
Band bottom: min 64 MHz
Default: 64/76 MHz for wide
band FM1/FM2
Band bottom: min 504 kHz
Default: 522 kHz
Band bottom: min 2.3 MHz
Default: 3.2/3.2/5.9/7.0/7.0/9.0/9.5/10.0 MHz for
wideband SW1 to SW8 respectively.
De-emphasis: 50 or 75 µs
Default: 75 µs
Channel space: 9 or 10 kHz
Default: 9 kHz
Tone/VOL mode: a-d
Default: d
Tuning preference: a-b
Default: a
Tuning preference: a-b
Default: a
Notes:
1. Tone/VOL mode has four modes:
Bass/treble
mode: no digital volume control, fixed volume level at 59
volume mode: no bass/treble effect, volume levels from 0 to 63
Mixed mode 1: bass/treble & digital volume coexist, volume levels from 0 to 63, scale to 0 ~59
Mixed mode 2: bass/treble & digital volume coexist, volume levels from 0 to 63
Digital
2. The Tuning preference of FM mode and SW mode has two preferences:
preference1:
preference2:
When tuning to adjacent channels, the volume level decreases by 2 dB.
When tuning to adjacent channels, the volume level remains unchanged.
3. There is no tuning preference selection for AM mode.
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
7
Rev. 0.1 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • October 2, 2021
Si4827-DEMO
4. Operation
The S4827-DEMO Board, a complete analog tune and digital display radio, provides two major modes of
operation: Time mode and FM/AM/SW Radio mode.
4.1. Time Mode
Put two AAA batteries into the battery compartment; the board will automatically enter Time Mode and display the
time. The DEMO board display in Time Mode is illustrated in Figure 1.
4.1.1. Time Setting
The time default value is 00:00 and can be set to the correct time manually when needed.
1. In Time Mode, press the BASS/TMR button to enter the setting menu. The default is to set the minute item
first. Press this button again to select the hour item. The selected item flashes.
2. While the selected item is flashing, press the DOWN/VOL- and UP/VOL+ button to set the desired time.
3. When you have finished setting the time, press the BASS/TMR button to quit the setting menu. The MCU
automatically quits the setting menu if there is no operation within 2 seconds.
4.1.2. Alarm Setting
1. In Time Mode, press the TREBLE/AL button to enable or disable the alarm function, and enter the setting
menu automatically when the alarm is enabled. Once you have entered the setting menu, the default is to
set the minute item first. Press this button again to select the hour item. The selected item flashes.
2. While the selected item is flashing, press the DOWN/VOL- and UP/VOL+ button to set the desired time.
3. When you have finished the alarm setting, press the TREBLE/AL button to quit the setting menu. The MCU
automatically quits the setting menu if there is no operation within 2 seconds.
4. If the alarm is enabled and the alarm setting time is matched, the radio will be automatically turned on after
the buzzer sounds for 5 seconds.
5. The radio will be turned off and the DEMO board will go into sleep mode automatically if there is no
operation on the buttons within 15 minutes; if there is any operation on the buttons, the auto-sleep function
will be disabled. The radio keeps working throughout this time.
8
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
Rev. 0.1 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • October 2, 2021
Si4827-DEMO
4.2. FM/AM/SW Radio Mode
In Time Mode, when a long press (hold time > 1s) on the POWER/BAND button or when the alarm time is reached,
the device will enter FM/AM/SW Mode. The LCD displays the following information: band indicator, band frequency
indicator, and sleep indicator in case radio is automatically turned on by the alarm.
The DEMO board display in FM/AM/SW Mode is illustrated in Figure 3.
Figure 3. LCD display in FM Radio Mode
The DEMO board provides two methods to select the radio band. One is to use the slide switch S2. The other is to
use the POWER/BAND push button. S14 determines which method is in use.
The DEMO board uses the keyboard to configure the band property. Refer to Section "4.2.1. MCU Setting Band
Property” for the operation details for setting the band property using the keypad.
To operate the DEMO board, follow these procedures:
1. According to the desired radio band selection method, set S14 to use slide switch or push button.
2. Hold the POWER/BAND button (hold time > 1s) or when the alarm time is reached, the device will enter
FM/AM/SW Mode.
3. Use slide switch S2 or press the POWER/BAND push button to select the desired band.
4. Refer to Section "4.2.1. MCU Setting Band Property” or section "4.2.2. MCU Setting Radio Working Mode”
to reconfigure the band property or radio working mode if necessary.
5. Rotate the tuning wheel and find the desired radio station with the help of the LCD display and/or tuning
indicator D1.
6. Rotate the volume control wheel VR2 and/or press the DOWN/VOL- or UP/VOL+ button to get a
comfortable volume. Press the BASS/TMR or TREBLE/AL button to get the desired bass/treble level.
Note: For FM listening, the earphone cable must be connected to the board when S12 is set to HP ANT or an external antenna
must be connected to the BNC connector when S12 is set to BNC.
For AM listening, the ferrite antenna must be connected to the board and the S11 is set to Ferrite before turning on the
radio or switching the band to AM.
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
9
Rev. 0.1 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • October 2, 2021
Si4827-DEMO
4.2.1. MCU Setting Band Property
The DEMO board enables the band property to be set by the MCU. The band property includes:
Band
top
Band
bottom
De-emphasis
Channel
(only for FM)
Space (only for AM)
The setting menu is illustrated in Figure 4.
To set the band properties, follow these steps:
1. Press the SETTING button to enter the setting menu and select the item to be set. The selected item
flashes for 1 second, then automatically switches to its current value.
2. While the value is flashing, press the DOWN/VOL- or UP/VOL+ button to set the desired value within 3
seconds.
3. Repeat step 1 and 2 to finish setting the band properties.
4. When the Band properties are set, the MCU automatically quits setting the menu if there is no operation
within 3 seconds.
5. In FM working mode, press the DE/SPC button to set the De-emphasis 50 µs or 75 µs.
6. In AM working mode, press the DE/SPC button to set the Channel Space 9 kHz or 10 kHz.
6(77,1*0(18
%DQG7RS
%DQG%RWWRP
7RQH9RO02'(
D%DVV7UHEOH02'(
7XQLQJSUHIHUHQFH
E'LJ9RO02'(
F0,;02'(
G0,;02'(
DSUHIHUHQFH
ESUHIHUHQFH
Figure 4. Setting Menu
4.2.2. MCU Setting Radio Working Mode
The host MCU can set the radio working mode
The working modes include:
Tone/volume
Tuning
mode, item 3 in setting menu
preference (only for FM and SW), item 4 in setting menu
To set radio working mode, follow these procedures:
1. Press the SETTING button to enter item 3. The LCD displays the item number st3 for 1 second, then
automatically switches to its mode indication.
2. Press the DOWN/VOL- or UP/VOL+ button to select the desired mode within 3 seconds.
3. Repeat steps 1 and 2 to set the tuning preference by setting the item 4.
4. When the radio working mode is set, the MCU automatically quits setting the menu if there is no operation
within 3 seconds.
10
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
Rev. 0.1 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • October 2, 2021
Si4827-DEMO
5. Bill of Materials
ATDD AM/FM/SW
LM4910 Audio
TM8723
See
receiver IC Si4827 with external 32.768 kHz crystal oscillator support
amplifier IC
MCU
Table 3 for details
Table 3. Si4827-DEMO Board Bill of Materials Rev 1.1
Item
Qty
Reference
Description
Value
1
12
C1-2 C6 C19 C24 C37-42 C44
CAP,SM,0603,X7R
0.1 µ
2
2
C5 C36
CAP,SM,0603,X7R
0.47 µ
3
2
C8 C10
CAP,SM,0603,COG
100 p
4
1
C33
CAP,SM,0603,COG
10 p
5
4
C28-29 C32 C35
CAP,SM,0603,COG
22 p
6
1
C11
CAP,SM,0603,COG
150 p
7
2
C30-31
CAP,SM,0603,X7R
33 n
8
1
C34
CAP,SM,0603,COG
33 p
9
1
C15
CAP,SM,0603,X7R
4.7 µ
10
2
C4 C12
CAP,SM,0603,X7R
10.0 µ
11
1
C13
CAP,SM,1210,X7R
47 µ
12
1
C18
CAP,SM,0603,COG
330 p
13
2
C23 C27
CAP,SM,1210,X7R
220 µ
14
2
C14 C25
Electrolytic capacitor
100 µ/4 V
15
1
C3
Electrolytic capacitor
220 µ/4 V
16
1
R25
RES,SM,0603
0R
17
1
R27
RES,SM,0603
100 R
18
2
R5 R6
RES,SM,0603
2k
19
1
R32
RES,SM,0603
10 R
20
1
R3
RES,SM,0603
10 k
21
1
R41
RES,SM,0603
120 k
22
1
R22
RES,SM,0603
12 k
23
2
R1-2
RES,SM,0603
1M
24
2
R4 R31
RES,SM,0603
1k
25
1
R24
RES,SM,0603
200 R
26
1
R13
RES,SM,0603
22 R
27
1
R16
RES,SM,0603
2.2 k
28
1
R46
RES,SM,0603
4.7 M
29
1
R20
RES,SM,0603
6.8 k
30
2
R21 R23
RES,SM,0603
NP
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
11
Rev. 0.1 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • October 2, 2021
Si4827-DEMO
Table 3. Si4827-DEMO Board Bill of Materials Rev 1.1
Item
Qty
Reference
Description
Value
31
1
R7
RES,SM,0603,Tolerance ±1%
10 k 1%
32
1
R29
RES,SM,0603,Tolerance ±1%
160 k 1%
33
9
R9-12 R14-15 R28 R33 R35
RES,SM,0603,Tolerance ±1%
20 k 1%
34
1
R43
RES,SM,0603,Tolerance ±1%
30 k 1%
35
1
R36
RES,SM,0603,Tolerance ±1%
33 k 1%
36
1
R8
RES,SM,0603,Tolerance ±1%
40 k 1%
37
1
R44
RES,SM,0603,Tolerance ±1%
47 k 1%
38
1
U1
SI4827-A SOIC16
Si4827-A
39
1
U2
LM4910MA,SO8
LM4910MA
40
1
U3
TM8795 44 PIN
TM8795 44 PIN
41
1
Q2
TRANSISTOR NPN SOT23
2N3904
42
1
Q1
TRANSISTOR NPN SOT23
2SC9018
43
1
Q3
TRANSISTOR NPN SOT23
2N3906
44
2
D2 D4
DIODE,SM,ESD,SOT23
BAV99
45
3
B4 B5 B6
FERRITE BEAD,SM,0603
2.5 k/100 M
46
1
B1
FERRITE BEAD,SM,0603
NP
47
1
BZ1
BUZZER
BUZZER
48
2
Y1-2
CRYSTAL
32.768 kHz
49
1
D1
LED
LED
50
1
D6
1N4148
1N4148
51
1
J5
Stereo earphone jack with switch
3.5 mm
52
1
L1
RES,SM,0603
0R
53
1
L2
IND,SM,0603
270 nH
54
1
L3
IND,SM,0603
120 nH
55
2
TP1 TP3
CONN,TH,1x2,HDR
CONN,TH,1x2,HDR
56
1
LCD1
LCD
LCD
57
1
J1
BNC VERTICAL
BNC for FM testing
58
1
J6
SMA VERTICAL
SMA for AM testing
59
1
ANT1
AW ferrite stick antenna
220 µH
60
1
BAT1
BATTERY BOX ,AAA*2 SIZE
61
3
S11 S12 S14
One pole two throw switch
62
1
S2
Single pole twelve throw switch
63
9
S1 S3-10
Push button
64
1
VR1
100 k,±10%,Variable resistor(POT)
100 k
65
1
VR2
10 k,±20%,Variable resistor(POT)
10k
12
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
Rev. 0.1 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • October 2, 2021
2.5k/100M
B6
LNA_EN [1,2]
33n
C30
R41
200k
C31
33n
R32
10R
10p
R31
1k
C33
S11
Q1
2SC9018
VCC
D2
BAV99
0.47u
C5
J6
RESET [2]
10k
R3
C19
0.1u
2k
R6
270nH
L2
C34
33p
[1] FMI
LNA_EN [1,2]
S12
1
L1
0R/120nH
C13
47u
C1
100R
R27
0.1u
R23
NC
VR1
100k 10%
[1] BAND
4
C36
0.47u
MW
3
C28
22p
C29
22p
R21
NC
U1
Si4827
[2]
[2] XTALI
TP1
IRQ
10u
C4
C39
0.1u
VCC
L3
120nH
VR2-A
C14
100u/4V
10u
C12
BAT1
AAA*2
R16
2k2
330p
C18
12k
R22
R5
2k
4
3
2
1
U2
LM4910MA
GND
SHUTDOWN
IN2
IN1
C11
R20
C25
100u/6.3V
VDD
VO3
VO2
VO1
150p
6k8
5
6
7
8
C24
0.1u
C27
220u
C23
220u
100p
C10
100p
GND
C8
TP3
Aout
GND
VCC
B4 2k5/100M
B5 2k5/100M
1
2
3
[1] FMI
Audio output
J5
BAND [1]
2-1 push button
2-3 slide switch
S14
2
S14: Band Selection
Figure 5. Si4827-DEMO Board Rev 1.1 Schematic (1 of 2)
32.768KHz
Y1
R46
4.7M
C15
0.1u 4.7u
C6
1
IRQ
3
2
VCC
8
AMI
7
GND
9
RSTB
5
SDIO
10
SDIO [2]
2
TUNE2
6
11
NC
FMI
SCLK
12
XTALO
SCLK [2]
BAND
XTALI
13
TUNE1
VDD
14
GND
15
AOUT
16
[1] TUNE1
Aout
D4
BAV99
[2]
SHUTDOWN
VCC
FM/SW
B1
J1
NC
ANT1
MW ferrite antenna
3
1
VCC
1
S2
2
3
4
5
6
7
8
9
10
11
12
13
R44
47k 1%
R33
20k 1%
R29
160k 1%
20k 1%
R28
10k 1%
R7
40k 1%
R8
R9
20k 1%
R14
20k 1%
R11
20k 1%
R12
20k 1%
R10
20k 1%
R15
20k 1%
R35
20k 1%
R43
30k 1%
R36
33k 1%
FM1 (W 64MHz - 108MHz ) (N 87MHz - 108MHz)
FM5 (W 76MHz - 108MHz) (N 64MHz - 87MHz)
AM1 (520kHz - 1710kHz)
AM2 (522kHz - 1620kHz)
SW1 (W 3.2MHz - 7.6MHz) (N 5.6MHz - 6.4MHz)
SW3 (W 3.2MHz - 10.0MHz) (N 6.8MHz - 7.6MHz)
SW5 (W 5.9MHz - 18.0MHz) (N 9.2MHz - 10.0MHz)
SW7 (W 7.0MHz - 16.0MHz) (N 11.45MHz - 12.25MHz)
SW9 (W 7.0MHz - 23.0MHz) (N 13.4MHz - 14.2MHz)
SW11 (W 9.0MHz - 22.0MHz) (N 15MHz - 15.9MHz)
SW13 (W 9.5MHz - 18.0MHz) (N 17.1MHz - 18MHz)
SW15 (W 10.0MHz - 22.0MHz) (N 21.2MHz - 22MHz)
(Note:W=Wide Band, N=Narrow Band)
TUNE1 [1]
Si4827-DEMO
6. Schematics and Gerber
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
13
Rev. 0.1 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • October 2, 2021
[2]
[2]
[2]
KEY_R1
[2]
KEY_C2
KEY_C3
[2]
KEY_C1
KEY_R0
[2]
KEY_C0
XTALI [1]
RESET
VCC
C40
0.1u
S7
11
10
9
8
7
6
5
S3
KEY2_DIP
C:ORCAD7.0CAPTURELIBRARYUSERS3C44B0XS3C44B0X.OLB
C:WIND95TEMP6200.LIB
KEY2_DIP
C:ORCAD7.0CAPTURELIBRARYUSERS3C44B0XS3C44B0X.OLB
C:WIND95TEMP6200.LIB
SETTING
S10
KEY
C:ORCAD7.0CAPTURELIBRARYUSERS3C44B0XS3C44B0X.OLB
C:WIND95TEMP6200.LIB
KEY2_DIP
TREBLE/AL
S6
KEY2_DIP
C:ORCAD7.0CAPTURELIBRARYUSERS3C44B0XS3C44B0X.OLB
C:WIND95TEMP6200.LIB
BASS/TMR
S5
KEY2_DIP
C:ORCAD7.0CAPTURELIBRARYUSERS3C44B0XS3C44B0X.OLB
C:WIND95TEMP6200.LIB
DE/SPC
KEY2_DIP
C:ORCAD7.0CAPTURELIBRARYUSERS3C44B0XS3C44B0X.OLB
C:WIND95TEMP6200.LIB
[2] KEY_C3
POWER/BAND
DOWN/VOLS9
KEY2_DIP
C:ORCAD7.0CAPTURELIBRARYUSERS3C44B0XS3C44B0X.OLB
C:WIND95TEMP6200.LIB
[2] KEY_C1
MCU
S4
COM2
COM1
CUP2
CUP1
VDD3
VDD2
VDD1
GND
XOUT
XIN
BAK
S8
KEY2_DIP
C:ORCAD7.0CAPTURELIBRARYUSERS3C44B0XS3C44B0X.OLB
C:WIND95TEMP6200.LIB
UP/VOL+
C38
0.1u
C44
0.1u
4
3
2
1
Q3
2N3906
IRQ [1]
U3
W/N BAND
W=Wide, N=Narrow
Y2
32.768KHz
C42
0.1u
KEY2_SM
C:ORCAD7.0CAPTURELIBRARYUSERS3C44B0XS3C44B0X.OLB
C:WIND95TEMP6200.LIB
LCD_C1 [2]
LCD_C2 [2]
C37
0.1u
VCC
C35
22p
C32
22p
VCC
S1
R2
1M
12
R24
[1] SHUTDOWN
[2] LCD_S13
23
24
25
26
27
28
29
30
31
32
R25
0R
1 Band Top
2 Band Bottom
3 Tone/Vol MODE
4 Tuning preference
SETTING MENU:
SEG9(K9)
SEG10(K10)
SEG11(K11)
SEG12(K12)
SEG21
SEG22
SEG23
SEG24/IOA1
SEG25/IOA2
SEG26/IOA3
33
200R
SEG27/IOA4
D1
Tuning indicator
LCD_S6
LCD_S7
LCD_S8
LCD_S9
LCD_S10
LCD_S11
LCD_S12
a Preference1
b Preference2
a Bass/Treble MODE
b Dig-Vol MODE
c MIX MODE1
d MIX MODE2
[2]
[2]
[2]
[2]
[2]
[2]
[2]
SDIO
RESET
SCLK
[1] LNA_EN
[1]
[1]
[1]
BZ
[2]
C2
0.1u
1k
R4
C3
220u/4V
Q2
2N3904
BZ1
BUZZER
D6
1N4148
R13
22R
VCC
[2] LCD_C1
1
COM1
[2] KEY_C2
[2]
[2] LCD_S2
[2] LCD_S1
FM
MW SW
COM2
R1
1M
44
TEST
43
13
COM3
42
INT
COM4
14
RESET
LCD_C3
15
COM5
41
SEG35/IOC4/KI4
SEG1(K1)
39
SEG33/IOC2/KI2
SEG3(K3)
[2] KEY_C0
38
SEG32/IOC1/KI1
SEG4(K4)
40
SEG34/IOC3/KI3
SEG2(K2)
[2]
17
[2]
LCD_S0
18
[2]
LCD_S1
16
[2]
KEY_R1
KEY_R0
2
[2] LCD_C2
COM3
[2] LCD_C3
3
[2] LCD_S0
4
SEG0
5
SEG1
6
SEG2
[2] LCD_S3
7
SEG3
[2] LCD_S4
8
SEG4
[2] LCD_S5
9
LCD
SEG5
[2] LCD_S6
10
SEG6
[2] LCD_S7
11
SEG7
[2] BZ
36
SEG30/IOB3/BZB
SEG6(K6)
35
SEG29/IOB2/ELP
SEG7(K7)
34
SEG28/IOB1/ELC
SEG8(K8)
37
SEG31/IOB4/BZ
SEG5(K5)
19
[2]
21
[2]
22
[2]
LCD_S5
20
[2]
LCD_S3
LCD_S2
SLEEP
SEG8
[2] LCD_S8
12
[2] LCD_S9
13
SEG9
[2] LCD_S10
14
SEG10
[2] LCD_S11
15
[2] LCD_S12
MHz
KHz
MHz
PM
SEG11
[2] LCD_S13
17
S
SEG13
16
SEG12
14
LCD_S4
C41
0.1u
LCD1
Si4827-DEMO
Figure 6. Si4827-DEMO Board Schematic Rev 1.1 (2 of 2)
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
Rev. 0.1 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • October 2, 2021
VCC
Si4827-DEMO
Figure 7. Si4827-DEMO Board Gerber Rev 1.1
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
15
Rev. 0.1 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • October 2, 2021
Connecting Everyone
and Everything,
All the Time
Portfolio
Quality
Support & Resources
www.skyworksinc.com
www.skyworksinc.com/quality
www.skyworksinc.com/support
Copyright © 2021 Skyworks Solutions, Inc. All Rights Reserved.
Information in this document is provided in connection with Skyworks Solutions, Inc. (“Skyworks”) products or services. These materials, including the
information contained herein, are provided by Skyworks as a service to its customers and may be used for informational purposes only by the customer.
Skyworks assumes no responsibility for errors or omissions in these materials or the information contained herein. Skyworks may change its documentation,
products, services, specifications or product descriptions at any time, without notice. Skyworks makes no commitment to update the materials or
information and shall have no responsibility whatsoever for conflicts, incompatibilities, or other difficulties arising from any future changes.
No license, whether express, implied, by estoppel or otherwise, is granted to any intellectual property rights by this document. Skyworks assumes no liability
for any materials, products or information provided hereunder, including the sale, distribution, reproduction or use of Skyworks products, information or
materials, except as may be provided in Skyworks’ Terms and Conditions of Sale.
THE MATERIALS, PRODUCTS AND INFORMATION ARE PROVIDED “AS IS” WITHOUT WARRANTY OF ANY KIND, WHETHER EXPRESS, IMPLIED, STATUTORY, OR
OTHERWISE, INCLUDING FITNESS FOR A PARTICULAR PURPOSE OR USE, MERCHANTABILITY, PERFORMANCE, QUALITY OR NON-INFRINGEMENT OF ANY
INTELLECTUAL PROPERTY RIGHT; ALL SUCH WARRANTIES ARE HEREBY EXPRESSLY DISCLAIMED. SKYWORKS DOES NOT WARRANT THE ACCURACY OR
COMPLETENESS OF THE INFORMATION, TEXT, GRAPHICS OR OTHER ITEMS CONTAINED WITHIN THESE MATERIALS. SKYWORKS SHALL NOT BE LIABLE FOR
ANY DAMAGES, INCLUDING BUT NOT LIMITED TO ANY SPECIAL, INDIRECT, INCIDENTAL, STATUTORY, OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT
LIMITATION, LOST REVENUES OR LOST PROFITS THAT MAY RESULT FROM THE USE OF THE MATERIALS OR INFORMATION, WHETHER OR NOT THE RECIPIENT
OF MATERIALS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
Skyworks products are not intended for use in medical, lifesaving or life-sustaining applications, or other equipment in which the failure of the Skyworks
products could lead to personal injury, death, physical or environmental damage. Skyworks customers using or selling Skyworks products for use in such
applications do so at their own risk and agree to fully indemnify Skyworks for any damages resulting from such improper use or sale.
Customers are responsible for their products and applications using Skyworks products, which may deviate from published specifications as a result of
design defects, errors, or operation of products outside of published parameters or design specifications. Customers should include design and operating
safeguards to minimize these and other risks. Skyworks assumes no liability for applications assistance, customer product design, or damage to any
equipment resulting from the use of Skyworks products outside of Skyworks’ published specifications or parameters.
Skyworks, the Skyworks symbol, Sky5®, SkyOne®, SkyBlue™, Skyworks Green™, Clockbuilder®, DSPLL®, ISOmodem®, ProSLIC®, and SiPHY® are trademarks or
registered trademarks of Skyworks Solutions, Inc. or its subsidiaries in the United States and other countries. Third-party brands and names are for
identification purposes only and are the property of their respective owners. Additional information, including relevant terms and conditions, posted at
www.skyworksinc.com, are incorporated by reference.
Skyworks Solutions, Inc. | Nasdaq: SWKS | sales@skyworksinc.com | www.skyworksinc.com
USA: 781-376-3000 | Asia: 886-2-2735 0399 | Europe: 33 (0)1 43548540 |
工商网监
湘ICP备2023018690号
