S i 5x x/ 5 14 / 57 0- PR OG -E V B
S i 514/ 570/ 571/ 598/ 599 A NY -F RE QUE NCY I 2 C
P ROGRAMMABL E X O/VC XO E VAL UAT I ON B OARD
Description
Features
The Skyworks Si514/570/571/598/599 evaluation kit
contains the hardware and software needed for
evaluation of the Si514/570/571/598/599 AnyFrequency I2C programmable XO/VCXO and can be
run on a USB-equipped PC.
Evaluation of Skyworks' Si514/570/571/598/599
Any-Frequency I2C programmable XO/VCXO
Windows-compatible software control and device
programming
Voltage regulator supports device operation of the
Si5xx at +1.8, +2.5, or +3.3 V
I2C communication options are jumper configurable
Voltage control (VC) input port (Si571/Si599)
Functional Block Diagram
TP1
(EXT3P3V)
TP2
(VBUS_5V)
J1
J2
Optional
Power In
USB
TP10
VCO In
1
REGIN
2
Filter
3
TP6 TP7
(SCL) (SDA)
J12
TP3
(VDD_DUT)
C8051F342
MCU
VDD
REG
J5
4
J20
3
2
1
Manual VDD
Voltage Select
4-3=2.5V
2-1=3.3V
OPEN=1.8V
1
2
3
J11
J17
2
TP4
1
J13
3
2
1
J16
2
SDA (VC)
J19
2
3
Output
Enable
3
GND
DUT
VDD
SCL (OE)
2
Level
Translator
NC (SCL)
Level
Translator
8
1
CLKP
NC (SDA)
1
CLKN
6
J14
5
4
CLKP
Output
Conditioner
J18
CLKN
7
1
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
Rev. 0.3 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • October 12, 2021
1. Introduction
This document describes the operation of the Skyworks Si514/570/571/598/599 evaluation kit. The Si5xx-PROGEVB kit refers to the evaluation board hardware and software intended for customer evaluation of the
Si514/570/571/598/599 Any-Frequency I2C programmable XO/VCXO. The Si5xx-EVB kit contains the following:
Si5xx-PROG-EVB Hardware
Programmable Oscillator Software
EVB Driver (USBXpress®)
The software components run on a USB-equipped PC and are described in detail in Section “5. Software Guide”
The Si5xx-PROG-EVB evaluation board can be used to evaluate the Si514, Si570, Si571, Si598, and Si599 I2C
programmable XOs or VCXOs as shown in Table 1. The Si514-PROG-EVB evaluation board can be used to
evaluate the Si514 I2C-programmable XO as shown in Table 1. This evaluation board functions and performs
similar to the Si5xx-PROG-EVB evaluation board.
Table 1. Si5xx XO and VCXO Device Evaluation Board Selector Guide
Ordering Part #
Type
Devices
Supported
Packages
Supported
Output Format,
Temp Stability,
Tuning Slope
Supported
Frequency
Range
Si5xx-EVB
Single/Dual Frequency
XO/VCXO Eval Board
Si510/511
Si512/513
Si515/516
Si530/531
Si532/533
Si550/552
Si590/591
5 x 7 mm, 6-pin
3.2 x 5 mm, 6-pin
3.2 x 5 mm, 4-pin
Any
100 kHz to
1417 MHz
Si5xx-PROG-EVB
I2C Programmable
XO/VCXO Eval Board
Si514
Si570/571
Si598/599
5 x 7 mm, 8-pin
5 x 7 mm 6-pin
3.2 x 5 mm, 6-pin
Any
100 kHz to
1417 MHz
Si514-PROG-EVB
I2C Programmable XO
Eval Board with soldered Si514
Si514
5 x 7 mm 6-pin
Any
100 kHz to
250 MHz
Si5xx5x7-EVB
Quad Frequency
XO/VCXO Eval Board
Si534
Si554
5 x 7 mm, 8-pin
Any
10 to
1417 MHz
Si570-PROG-EVB
I2C Programmable XO
Eval Board with soldered Si570
Si570
5x7 mm 8-pin
Any
10 to
1417 MHz
Notes:
1. Si5xx samples must be ordered separately from the Si5xx-PROG-EVB.
2. Board must be modified to be consistent with the ordered part. See "3.10. Output Terminations" on page 8.
3. Si514-PROG-EVB comes with an Si514 preinstalled.
2
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
Rev. 0.3 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • October 12, 2021
1.1. Quick Start
1. Install an Si514, Si570, Si571, Si598, or Si599 device on the board (Si514-PROG-EVB comes with an Si514
preinstalled; the Si570-PROG-EVB also comes with an Si570 installed).
2. Verify that the jumper settings are correct.
3. Connect the USB cable from the EVB to the host PC.
4. Install the Programmable Oscillator Software and driver.
5. Launch the Programmable Oscillator Software by clicking Start Programs Skyworks Programmable
Oscillator Software. Click on one of the shortcuts in the group.
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
3
Rev. 0.3 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • October 12, 2021
2. Top/Bottom Views of Board
Status
LEDs
(b)
Figure 1. Board Views (a) Top; (b) Bottom
4
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
Rev. 0.3 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • October 12, 2021
3. Functional Description
The Si5xx-PROG-EVB is the evaluation board assembly for the Si514/570/571/598/599 Any-Frequency I2C
Programmable XO/VCO. This evaluation board assembly provides access to all signals for programming and
operating the device. The Si5xx-PROG-EVB schematics, bill of materials, and PCB layouts are included as
sections 6, 7, and 8, respectively. Figure 2 provides a block diagram for the board.
TP1
(EXT3P3V)
TP2
(VBUS_5V)
J1
J2
Optional
Power In
USB
TP10
VCO In
1
REGIN
2
Filter
3
TP6 TP7
(SCL) (SDA)
J12
TP3
(VDD_DUT)
C8051F342
MCU
VDD
REG
J5
J20
4
3
2
1
Manual VDD
Voltage Select
4-3=2.5V
2-1=3.3V
OPEN=1.8V
1
2
3
J11
J17
2
TP4
1
J13
3
2
1
J16
2
SDA (VC)
J19
2
3
Output
Enable
3
GND
DUT
VDD
SCL (OE)
2
Level
Translator
NC (SCL)
Level
Translator
1
CLKP
NC (SDA)
1
8
CLKN
6
J14
5
4
CLKP
Output
Conditioner
J18
CLKN
7
1
Figure 2. Si5xx-PROG-EVB Functional Block Diagram
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
5
Rev. 0.3 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • October 12, 2021
3.1. Power Supply
The Si5xx-PROG-EVB is pre-configured to accept 5 V from the USB connector at J2. The DUT is powered from
the VDD regulator by default, but could be changed to an external supply introduced through J1. To do this, simply
move jumper J11 from pins 2-3 to 1-2 and apply power to J1. (Ensure the voltage range of the DUT is obeyed, and
it is also good practice to set a current limit on the power supply).
It is also possible for the microcontroller (U9) to adjust the VDD regulator through the software. The microcontroller
has pull-downs configured at P0.0 and P0.1 that grounds R18 and R19, respectively, adjusting VDD_DUT to 1.8,
2.5, or 3.3 V. It is also possible to install jumpers in J5 to manually force a VDD_DUT voltage. Table 2 illustrates the
settings of J5:
Table 2. J5 settings for VDD_DUT
Jumper
VDD_DUT
Open
1.8 V
1–2
3.3 V
3–4
2.5 V
3.2. Reset Circuit
The Si5xx-PROG-EVB MCU may be reset by momentarily pressing pushbutton SW1.
3.3. USB
A 4-pin USB receptacle is provided at location J2. The Si5xx-PROG-EVB is compatible with USB Specification 2.0.
When the USB link is in use, the MCU drives LED D4.
3.4. MCU
The Skyworks MCU, P/N C8051F342, provides the following functions:
Supports I2C communication to the DUT on behalf of the host PC per the Programmable Oscillator Software
Drives a number of status indicator LEDs (see Table 3)
Supplies 3.3 V to peripheral ICs on the motherboard but not to the DUT
Controls DUT power (see Section “3.1. Power Supply” )
Auto-detects the part type (e.g., Si51x/Si57x/Si59x)
There is a provision for in-circuit programming at connector J4. This provision should not be needed in normal
operation. The host PC operates the software and communicates to the Si5xx-PROG-EVB through the MCU via
USB connector J2. When the USB link is in use, LED D4 should flash. The MCU may be reset by momentarily
pressing pushbutton (SW1).
6
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
Rev. 0.3 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • October 12, 2021
3.5. Status Signals
There are four LEDs on the Si5xxPROG-EVB that report visual status as listed in Table 3 and shown in Figure 1b.
Upon powerup, D1 should be illuminated.
Table 3. Si5xx-PROG-EVB LEDs
LED
ON
OFF
D1
VDD3p3 volts is present
VDD3p3 volts is NOT present
D2
Ext3p3V volts is present
Ext3p3V volts is NOT present
D3
Reserved
Reserved
D4
USB access in progress
No USB access in progress
3.6. Jumpers
There are seven jumper locations on the Si5xx-PROG-EVB as listed in Table 4. The default or pre-loaded jumpers
are shown in Figure 1a.
Table 4. Si5xx-PROG-EVB Jumpers
Jumper Block Reference
Function
J5
Manual (on-board) VDD_DUT adjust (see Table 1)
J11
VDD_DUT select:
1-2: External voltage (from J1)
2-3: On-board regulator
J13
I2C/Vc selector:
1-2: I2C communication
3-4: Ext Vc input (Si57x)
J16
Output enable (Si57x):
1-2: OE is HIGH
3-4: OE is LOW
J17
Manual shutdown of I2C port for Si514 (also controllable via SW)
J19
Manual shutdown of I2C port for Si57x (also controllable via SW)
J20
I2C communication access port
3-4: SCL connection to MCU
5-6: SDA connection to MCU
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
7
Rev. 0.3 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • October 12, 2021
3.7. External I2C Communication
It is possible to use an external I2C controller to communicate with the DUT. To do this, remove the jumpers
installed in J20 and connect the external I2C harness to J20. Grounded pins (1-2, 7-8) are there for grounding the
harness. Pins 4 and 6 can be driven as SCL and SDA, respectively.
3.8. Si5xx-PROG-EVB Digital Control Signal
One normally static digital input control signal routes to the Si5xx: Output Enable or OE. By default, the OE signal
is pulled HIGH on the Si5xx-PROG-EVB and may be pulled low by installing a jumper at J16.
3.9. Si5xx-PROG-EVB Voltage Control Signal
An external voltage control signal may be applied to the control voltage modulation input at the J12 header
(VCO_IN). This voltage supplies the control voltage or voltage modulation input to the DUT. J13 should be installed
in the 2-3 position.
3.10. Output Terminations
The Si5xx-PROG-EVB can support four different output formats: CMOS, LVPECL, LVDS, and HCSL. There are
output resistors that are needed to accompany each format. Table 5 shows which resistors are needed for each
output:
Table 5. Output Termination Installation Definition
8
Output
Format
R36
R40
R35
R44
R37
R38
R29
R34
R43
R45
CMOS
10
10
NP
NP
NP
NP
NP
NP
NP
NP
LVPECL
0
0
130
130
NP
NP
NP
0
NP
0
LVDS
0
0
NP
NP
NP
NP
NP
NP
NP
NP
HCSL
0
0
NP
NP
NP
NP
NP
NP
NP
NP
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
Rev. 0.3 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • October 12, 2021
4. Configuring the Si5xx-PROG-EVB
1.8-3.3V Power Supply
(Optional) - +
PC
USB
-
+
VC
-
-
+
Optional Voltage Source
(for Si571)
Optional I2C Device
+
Si5xx-EVB
Frequency Counter
Optional Oscilloscope
or other Instrument
SCL/SDA
CLKN
CLKP
Figure 3. Si5xx-PROG-EVB Typical Configuration
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
9
Rev. 0.3 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • October 12, 2021
5. Software Guide
The evaluation kit includes software called Programmable Oscillator Software, which consists of several tools:
Programmable Oscillator Calculator—Program new dividers and output frequencies in the device using large
and small frequency programming procedures. This can run with or without an EVB connected to the computer.
Register Programmer—Program individual registers on the oscillator device on the EVB.
Si57x/9x Register Programmer—Program Si570/571/598/599 specific registers.
Register Viewer—View all the register values on the oscillator installed on the EVB.
User Guide—Read more help information on using the software.
Spreadsheet Finder for HS_DIV and N1—Use an Excel spreadsheet to find the Si570/571/598/599 dividers.
No EVB is required.
5.1. Programmable Oscillator Software Installation
The following sections describe how to install and use the software. There is a readme.txt file with the installation
files as well as a software user guide installed with the software.
5.2. System Requirements
Microsoft Windows® 2000, XP, Vista, 7
USB 2.0
2 MB of free hard drive space
1024 x 768 screen resolution or greater
Microsoft .NET Framework 1.1
USBXpress 3.1.1 driver
Note: USBXpress 3.1.1 driver is provided and installed with the software. Newer or older versions of USBXpress available
from other EVB kits or online have not been tested with this software.
5.3. Microsoft .NET Framework Installation
The Microsoft .NET Framework is required before installing and running the software. Details and installation
information about the .NET Framework are available via a shortcut in the NETFramework directory or at the
following web site:
www.microsoft.com/downloads/details.aspx?FamilyId=262D25E3-F589-4842-8157034D1E7CF3A3&displaylang=en
There are multiple versions of the .NET Framework available from Microsoft, and they can be installed side-by-side
on the same computer. The software requires Version 1.1 but can run under other versions. Contact your system
administrator for more details.
5.4. Programmable Oscillator Software Installation
The Programmable Oscillator Software is installed from the ProgOscSwInstall.exe file.
1. Double-click the install file to start the wizard.
2. Follow the wizard instructions to complete the installation for both the software and the driver. Use the default
installation location for best results.
3. After the installation is complete, click on Start Programs Skyworks Programmable Oscillator Software.
Select one of the items in the menu including the User Guide to get more details on how to run the software.
5.5. Programmable Oscillator Software Uninstall
Close all the programs and help files before running the uninstaller to ensure complete removal of the software. To
uninstall the software, use the Add and Remove Programs utility in the Control Panel or click Start Programs
Skyworks Programmable Oscillator Software Uninstaller.
Note: The driver software must be uninstalled separately.
10
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
Rev. 0.3 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • October 12, 2021
6. Schematic
TP2
VDD3P3
1
5
2
6
Note 3
2
PWR_SEL1
1
PWR_SEL2
EN1 32
EN2 31
30
29
28
27
C8
2200pF
SDA
SCL
26
25
Board_ID 24
23
22
21
20
19
7
P0.0
P0.1
P0.2
P0.3
P0.4
P0.5
P0.6
P0.7
4
S1
S2
1
RST/C2CK
P3.0/C2D
VBUS
D+
D-
3
6
VDD
Red
4
REGIN
Red
U9
USB
9 MCU_C2CK
10
8
4
5
VDD3P3
P1.0
P1.1
P1.2
P1.3
P1.4
P1.5
P1.6
P1.7
P2.7
P2.6
P2.5
P2.4
P2.3
P2.2
P2.1
P2.0
GND
1 C
2
1 C
Grn
VC_Filter
1
J2
SP0503BAHT
V
U1
3
Gnd
A
D4
R5
0 ohm
C7
4.7uF
C6
100N
100
2
C
R6
1
R7
49.9
Grn
VDD5V OK
L2
1
2
3
100N
VDD
OK
D-
D3
A
J12
D1
R4
301
D+
R3
301
2
R2
127
C5
22pF
A
C2
2200pF
2
C4
33UF
2
+
A
C3
33UF
2
+
C1
1
1
D2
VCO in
R1
127
2
C
1
1
*
*
2
1
VBUS_5V
Ext3p3V
L1
J1
Optional
POWER IN
11
12
13
14
15
16
17
18
Brd_Cnfg7
Brd_Cnfg6
Brd_Cnfg5
Brd_Cnfg4
Brd_Cnfg3
Brd_Cnfg2
Brd_Cnfg1
Brd_Cnfg0
In-Circuit
Programming
Connector
2
4
6
8
10
R9
1
3
5
7
9
R8
0 ohm
VDD3P3
MCU_RSTN
MCU_C2CK
1K
3
C8051F342
J4
VDD_MID
R11
TP3
R10
1K
R12 10
1K
1
4.99K
U4
R18
17.4K
.5%
R19
8.25K
Brd_Cnfg0
Brd_Cnfg1
Brd_Cnfg2
Brd_Cnfg3
Brd_Cnfg4
Brd_Cnfg5
Brd_Cnfg6
Brd_Cnfg7
J5
4
2
3
1
J8
J9
1
1
J10
0 ohm R20
J7
1
J6
1
4-3 = 2.5V
2-1 = 3.3V
OPEN = 1.8V
Vout = 1.25*(1+Rtop/Rbot)
1
1
DS2411
.5%
VBUS_5V
Sprinkle around DUT
VDD_DUT
VDD_DUT
VDD_DUT
Ext3p3V
TP5
TP4
J11
SCL2
5
R32
2.2K
R33
2.2K
R47 0 ohm
1
100N
VREF1
SCL1
SDA2
C26
1UF
SDA1
J13
2
SDA(Vc)
SCL(OE)
8
VDD
7
VDD_DUT
GND
NC(SDA)
1
3
R39
200K
CLKP
CLKOB
6
0 ohm
5
100N
R37
49.9
Output Resistor Configurations for Various
Output Formats (R in Ohms)
Output
R36 R40 R35 R44 R37 R38 R29 R34
Format
10
10
NP
NP
NP
NP
NP
NP
CMOS
J14
C20
1
CLKN
1
2
3
Output
Enable
2
1
Disable
Pins 1&2
Com.
NC(SCL)
1
J16
VBUS_5V
J17
C18
5pF
R36
U7
1
2
3
1
PCA9306
R35
130
C19
100N
4
GND
TP7
R34
0 ohm
Note 1
3
LVPECL
Si514_70_71
R40
J18
C21
1
PIN Labling:()=570 or 571,514 othrwz
0 ohm
100N
CLKO
R41
2.2K
R42
2.2K
TP9
SCL2
SCL1
SDA2
SDA1
3
R44
130
R45
4
GND
1
R43
2K
PCA9306
R46
VC_Filter
C24
5pF
0 ohm
1
2
1
100N
0 ohm
5
J19
Disable
Pins 7&8
Com.
U8
2
VREF1
1
6
VREF2
EN
(No Pop)
7
8
(No Pop)
C22
EN2
Note 3
C25
100N
Notes:
1)
2)
3)
4)
Mount close to DUT
Mount close to pins 1 & 2 of the DUT
Install for VCOs
100 OHM Diff. Impedance, 50 OHM to GND
0
130
NP
HCSL
0
0
NP
- NP = No Pop
R38
49.9
VDD_DUT
C23
0
0
NOTE 4
4
TP8
100N
LVDS
2
3
4
5
6
U6
2
VREF2
EN
8
2
3
4
5
EN1
2
4
6
8
(No Pop)
J20
1
3
5
7
(No Pop)
SDA
4.99K
4.99K
1
SCL
1
7
TP6
R29
2K
3
2
1
C17
R31
(No Pop)
C16
(No Pop)
R28
200K
100N
R30
0 ohm R27
.5%
Board_ID
0 ohm R26
Vcc
R17
22.6K
2
0 ohm R25
U5
NC1
I/O
NC2 Ser No.
NC3
C12
100N
MIC5301
GND
3
4
5
C11
1UF
R14
4.99K
0 ohm R24
2
SW1
NO
VDD_MID
C10
4.7uF
C9
100N
R15
10K
0 ohm R23
6
C15
4.7uF
C14
100N
4.99K
4
0 ohm R22
R16
C13
100N
R13
5
Vout
EN ADJ
GND
0 ohm R21
Vin
3
3
4
1
VDD3P3
2
1
VDD_DUT
VBUS_5V
1
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
11
Rev. 0.3 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • October 12, 2021
TP1
TP10
Figure 4. Si5xx-PROG-EVB (Universal I2C XO/VCXO)
0
130
NP
NP
R43
NP
NP
NP
NP
0
NP
NP
NP
NP
NP
NP
NP
NP
NP
NP
NP
R45
NP
0
NP
NP
7. Bill of Materials
Table 6. Si5xx-PROG-EVB/Si514-PROG-EVB/Si570-PROG-EVB Bill of Materials1
Item
Qty
Reference
Value
Mfr
Manufacturer PN
PCB Footprint
1
14
C1,C6,C9,
C12,C13,
C14,C16,
C17,C19,
C20,C21,
C22,C23,
C25
100 nF
Venkel
C0603X7R160-104KNE
SM_C_0603
2
2
C2,C8
2200 pF
Venkel
C0603X7R160-222KNE
SM_C_0603
3
2
C3,C4
33 µF
Venkel
TA006TCM336KBR
EIA 3528
4
1
C5
22 pF
Venkel
C0603C0G500-220KNE
SM_C_0603
5
3
C7,C10,C15
4.7 µF
Venkel
C0805X5R6R3-475KNE
SM_C_0805
6
2
C11,C26
1 µF
Venkel
C0603X7R6R3-105KNE
SM_C_0603
7
2
D1,D2
Grn
Panasonic
LN1371G
LED_gull
8
2
D3,D4
Red
Lumex
LN1271RAL
LED_gull
9
1
J1
Phoenix_2_screw
Phoenix
MKDSN 1.5/2-5.08
Phoenix2pinM_p2pitch
10
1
J2
USB
FCI
61729-0010BLF
USB_typeB
11
1
J4
5by2_Shrd_Hdr_SMT
Sullins
PPTC052LJBN-RC
5by2header_thruhole
12
1
J5
2by2_M_Hdr
Sullins
PBC36DAAN
2by2header_p1pitch
13
5
J6,J7,J8,J9,
J10
Jmpr_1pin
Tyco
87224-1
1by1header_TH
14
4
J11,J12,J13,J1
6
Jmpr_3pin
Tyco
146225-3
3pin_p1pitch
15
2
J14,J18
SMA_VERT
Johnson
142-0701-211
SMA_VERT
16
2
J17,J19
Jmpr_2pin
Sullins
PBC36DAAN
2by2header_p1pitch
17
1
J20
4X2 Header
Sullins
PBC04DFAN
4by2header_p1pitch
18
2
L1,L2
Ferrite
Murata
BLM31A601S
1206
19
2
R1, R2
127
Venkel
CR0603-16W-1270FT
SM_R_0603
Notes:
1. Outputs configured for LVPECL.
2. Si514-PROG-EVB contains a presoldered 514CBA000118AAG device.
3. Si570-PROG-EVB contains a presoldered 570ACA000118DG.
12
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
Rev. 0.3 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • October 12, 2021
Table 6. Si5xx-PROG-EVB/Si514-PROG-EVB/Si570-PROG-EVB Bill of Materials1 (Continued)
Item
Qty
Reference
Value
Mfr
Manufacturer PN
PCB Footprint
20
3
R3,R4
301
Venkel
CR0603-16W-3010FT
SM_R_0603
21
16
R5,R8,R20,
R21,R22,
R23,R24,
R25,R26,
R27,R34,
R36,R40,
R45,R46,
R47
0
Venkel
CR0603-16W-000T
SM_R_0603
22
1
R6
100
Venkel
CR0603-16W-1000FT
SM_R_0603
23
1
R7
49.9
Venkel
CR0603-16W-49R9FT
SM_R_0603
24
3
R9,R10,R11
1 k
Venkel
CR0603-16W-1001FT
SM_R_0603
25
1
R12
10
Venkel
CR0603-16W-10R0FT
SM_R_0603
26
1
R15
10 k
Venkel
CR603-16W-1002FT
SM_R_0603
27
5
R13,R14,
R16,R30,
R31
4.99 k
Venkel
CR0603-16W-4991FT
SM_R_0603
28
1
R17
22.6 k
Venkel
CR0603-16W-2262FT
SM_R_0603
29
1
R18
17.4 k
Venkel
CR0603-16W-1742FT
SM_R_0603
30
1
R19
8.25 k
Venkel
CR0603-16W-8251FT
SM_R_0603
31
2
R28,R39
200 k
Venkel
CR0603-16W-2003FT
SM_R_0603
32
4
R32,R33,R41,
R42
2.2 k
Venkel
CR0603-16W-2201FT
SM_R_0603
33
2
R35,R44
130
Venkel
CR0603-16W-1300FT
SM_R_0603
34
1
SW1
NO
Mountain
Switch
101-0161-EV
4pinSwitch
35
2
TP1,TP10
Test Point
Key Stone
5001K
.035" TH
36
1
U1
SP0503BAHT
Little Fuse
SP0503BAHT
SOT143
37
1
U4
MIC5301
Micrel
MIC5301YD5
SOT23-5
38
1
U5
DS2411
Maxim/
Dallas
DS2411RP+
TSOC-6
39
2
U6,U8
PCA9306
TI
PCA9306DCTR
PSOP
40
1
U9
C8051F342
Skyworks
C8051F342-GQ
LQFP-32
Notes:
1. Outputs configured for LVPECL.
2. Si514-PROG-EVB contains a presoldered 514CBA000118AAG device.
3. Si570-PROG-EVB contains a presoldered 570ACA000118DG.
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
13
Rev. 0.3 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • October 12, 2021
Table 6. Si5xx-PROG-EVB/Si514-PROG-EVB/Si570-PROG-EVB Bill of Materials1 (Continued)
Item
Qty
Reference
Value
Mfr
Manufacturer PN
PCB Footprint
Not Populated
412
U7
Si514_70_71
Skyworks
42
R29,R43
2 k
Venkel
CR0603-16W-2001FT
SM_R_0603
43
C18,C24
5 pF
Venkel
C0603X7R160-104KNE
SM_C_0603
44
R37,R38
49.9
Venkel
CR0603-16W-49R9FT
SM_R_0603
45
TP2,TP3,
TP4,TP5,
TP6,TP7,
TP8,TP9
Test Point
Key Stone
5001K
.035" TH
Notes:
1. Outputs configured for LVPECL.
2. Si514-PROG-EVB contains a presoldered 514CBA000118AAG device.
3. Si570-PROG-EVB contains a presoldered 570ACA000118DG.
Part Order Code
Type
Package
Output
Frequency Range
Starting Frequency
VDD
Temperature Stability
Total Stability
Opening Temperature Range
Data Sheet
514CBA000118AAG
I2C Programmable
5x7 mm, 6-Pin
CMOS
0.10–212.5 MHz
156.25 MHz
3.3 V
±25 ppm
±50 ppm
–40 to 85 °C
www.skyworksinc.com/support-ia
Part Order Code
Type
Package
Output
Frequency Range
Starting Frequency
570ACA000118DG
I2C programmable
5x7 mm, 8 pin
LVPECL
10–945, 970–1134, 1213–1417.5 MHz
156.25 MHz
VDD: 3.3 V
3.3 V
20 ppm
–40 to 85 °C
www.skyworksinc.com/support-ia
VDD
Total Stability
Opening Temperature Range
Data Sheet
14
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
Rev. 0.3 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • October 12, 2021
8. Layout
Figure 5. Primary Side
Figure 6. Layer 2: PWR
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
15
Rev. 0.3 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • October 12, 2021
Figure 7. Layer 3: GND
Figure 8. Secondary Side
16
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
Rev. 0.3 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • October 12, 2021
DOCUMENT CHANGE LIST
Revision 0.1 to Revision 0.2
Added ordering information and revised text to add the Si514-PROG-EVB to the list of released EVBs.
Updated Table 5 on page 8.
Updated Figure 4 on page 11 (schematic).
Updated "7. Bill of Materials" on page 12 and notes.
Described
changes needed for the Si514-PROG-EVB.
Revision 0.2 to 0.3
Added ordering information and revised test for the newly released Si570-PROG-EVB
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
17
Rev. 0.3 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • October 12, 2021
NOTES:
18
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
Rev. 0.3 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • October 12, 2021
ClockBuilder Pro
Customize Skyworks clock generators,
jitter attenuators and network
synchronizers with a single tool. With
CBPro you can control evaluation
boards, access documentation, request
a custom part number, export for
in-system programming and more!
www.skyworksinc.com/CBPro
Portfolio
SW/HW
Quality
Support & Resources
www.skyworksinc.com/ia/timing
www.skyworksinc.com/CBPro
www.skyworksinc.com/quality
www.skyworksinc.com/support
Copyright © 2021 Skyworks Solutions, Inc. All Rights Reserved.
Information in this document is provided in connection with Skyworks Solutions, Inc. (“Skyworks”) products or services. These materials, including the
information contained herein, are provided by Skyworks as a service to its customers and may be used for informational purposes only by the customer.
Skyworks assumes no responsibility for errors or omissions in these materials or the information contained herein. Skyworks may change its documentation,
products, services, specifications or product descriptions at any time, without notice. Skyworks makes no commitment to update the materials or
information and shall have no responsibility whatsoever for conflicts, incompatibilities, or other difficulties arising from any future changes.
No license, whether express, implied, by estoppel or otherwise, is granted to any intellectual property rights by this document. Skyworks assumes no liability
for any materials, products or information provided hereunder, including the sale, distribution, reproduction or use of Skyworks products, information or
materials, except as may be provided in Skyworks’ Terms and Conditions of Sale.
THE MATERIALS, PRODUCTS AND INFORMATION ARE PROVIDED “AS IS” WITHOUT WARRANTY OF ANY KIND, WHETHER EXPRESS, IMPLIED, STATUTORY, OR
OTHERWISE, INCLUDING FITNESS FOR A PARTICULAR PURPOSE OR USE, MERCHANTABILITY, PERFORMANCE, QUALITY OR NON-INFRINGEMENT OF ANY
INTELLECTUAL PROPERTY RIGHT; ALL SUCH WARRANTIES ARE HEREBY EXPRESSLY DISCLAIMED. SKYWORKS DOES NOT WARRANT THE ACCURACY OR
COMPLETENESS OF THE INFORMATION, TEXT, GRAPHICS OR OTHER ITEMS CONTAINED WITHIN THESE MATERIALS. SKYWORKS SHALL NOT BE LIABLE FOR
ANY DAMAGES, INCLUDING BUT NOT LIMITED TO ANY SPECIAL, INDIRECT, INCIDENTAL, STATUTORY, OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT
LIMITATION, LOST REVENUES OR LOST PROFITS THAT MAY RESULT FROM THE USE OF THE MATERIALS OR INFORMATION, WHETHER OR NOT THE RECIPIENT
OF MATERIALS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
Skyworks products are not intended for use in medical, lifesaving or life-sustaining applications, or other equipment in which the failure of the Skyworks
products could lead to personal injury, death, physical or environmental damage. Skyworks customers using or selling Skyworks products for use in such
applications do so at their own risk and agree to fully indemnify Skyworks for any damages resulting from such improper use or sale.
Customers are responsible for their products and applications using Skyworks products, which may deviate from published specifications as a result of
design defects, errors, or operation of products outside of published parameters or design specifications. Customers should include design and operating
safeguards to minimize these and other risks. Skyworks assumes no liability for applications assistance, customer product design, or damage to any
equipment resulting from the use of Skyworks products outside of Skyworks’ published specifications or parameters.
Skyworks, the Skyworks symbol, Sky5®, SkyOne®, SkyBlue™, Skyworks Green™, Clockbuilder®, DSPLL®, ISOmodem®, ProSLIC®, and SiPHY® are trademarks or
registered trademarks of Skyworks Solutions, Inc. or its subsidiaries in the United States and other countries. Third-party brands and names are for
identification purposes only and are the property of their respective owners. Additional information, including relevant terms and conditions, posted at
www.skyworksinc.com, are incorporated by reference.
Skyworks Solutions, Inc. | Nasdaq: SWKS | sales@skyworksinc.com | www.skyworksinc.com
USA: 781-376-3000 | Asia: 886-2-2735 0399 | Europe: 33 (0)1 43548540 |
工商网监
湘ICP备2023018690号
