SL28541-2
Clock Generator for Intel®Mobile Chipset
Features
• 33 MHz PCI clocks
• Intel® CK505 Rev. 1.0 Compliant
• Low power push-pull type differential output buffers
• Integrated voltage regulator
• Integrated resistors on differential clocks
• Scalable low voltage VDD_IO (1.05V to 3.3V)
• 8-step programmable drive strength for single-ended
clocks
• Differential CPU clocks with selectable frequency
• 100 MHz Differential SRC clocks
• 100 MHz Differential LCD clock
• 96 MHz Differential DOT clock
• 48 MHz USB clock
• 27 MHz Video clocks
• Buffered Reference Clock 14.318 MHz
• 14.318 MHz Crystal Input or Clock Input
• Low-voltage frequency select input
• I2C support with readback capabilities
• Ideal Lexmark Spread Spectrum profile for maximum
electromagnetic interference (EMI) reduction
• Industrial Temperature -40°C to 85°C
• 3.3V Power supply
• 56-pin TSSOP packages
CPU
SRC
x2 / x3
x5/9
PCI REF DOT96 USB_48 LCD
x6
x1
x1
27M
x1
Pin Configurations
Block Diagram
PCI0/OE#_0/2_A
VDD_PCI
PCI1/OE#_0/2_A
PCI2/TME
PCI3
PCI4/GCLK_SEL
PCIF0/ITP_EN
VSS_PCI
VDD_48
USB_48/ FSA
VSS_48
VDD_IO
SRC0/DOT96
SRC0#/DOT96#
VSS_IO
VDD_PLL3
SRC1/LCD100/27M_NSS
SRC1#/LCD100#/27M_SS
VSS_PLL3
VDD_PLL3_IO
SRC2/SATA
SRC2#/SATA#
VSS_SRC
SRC3/OE#_0/2_B
SRC3#/OE#_1/4_B
VDD_SRC_IO
SRC4
SRC4#
........................ DOC #: SP-AP-0064 (Rev. AB) Page 1 of 28
400 West Cesar Chavez, Austin, TX 78701
1+(512) 416-8500
x1
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
1+(512) 416-9669
56
55
54
53
52
51
50
49
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
SCLK
SDATA
REF0/FSC/TEST_SEL
VDD_REF
XIN/CLKIN
XOUT
VSS_REF
FSB/TEST_MODE
CKPWRGD/PD#
VDD_CPU
CPU0
CPU#0
VSS_CPU
CPU1
CPU1#
VDD_CPU_IO
NC
SRC8/ CPU2_ITP
SRC8#/ CPU2_ITP#
VDD_SRC_IO
SRC7/OE#_8
SRC7#/OE#_6
VSS_SRC
SRC6
SRC#
VDD_SRC
PCI_STP#
29 CPU_STP#
www.silabs.com
x2
SL28541-2
56 TSSOP Pin Definition
Pin No.
Name
1
PCI0/OE#_0/2_A
Type
Description
I/O, SE 3.3V, 33MHz clock/3.3V OE# Input mappable via I2C to control either SRC0 or
SRC2. (Default PCI0, 33MHz clock)
2
VDD_PCI
PWR
3.3V Power supply for PCI PLL.
3
PCI1/OE#_1/4_A
I/O, SE 3.3V, 33MHz clock/3.3V OE# Input mappable via I2C to control either SRC1 or
SRC4. (Default PCI1, 33MHz clock)
4
PCI2/TME
I/O, SE 3.3V tolerance input for overclocking enable pin/3.3V, 33MHz clock.
(Refer to DC Electrical Specifications table for Vil_FS and Vih_FS specifications)
5
PCI3
O, SE, 33 MHz clock.
6
PCI4 / GCLK_SEL
I/O, SE 33 MHz clock output/3.3V-tolerant input for selecting graphic clock source on pin
13, 14, 17and 18
Sampled on CKPWRGD assertion
GCLK_SEL
7
PCIF_0/ITP_EN
8
VSS_PCI
GND
9
VDD_48
PWR
10
USB_48/FSA
11
VSS_48
Pin13
Pin14
Pin17
Pin 18
0
DOT96T DOT96C SRC1T/LCD_100T SRC1C/LCD_100C
1
SRCT0
SRCC0
27M_NSS
27M_SS
I/O, SE 3.3V LVTTL input to enable SRC8 or CPU2_ITP/33 MHz clock output. (sampled
on the CK_PWRGD assertion)
1 = CPU2_ITP, 0 = SRC8
I/O
Ground for outputs.
3.3V Power supply for outputs and PLL.
3.3V tolerant input for CPU frequency selection/fixed 3.3V, 48MHz clock output.
(Refer to DC Electrical Specifications table for Vil_FS and Vih_FS specifications)
GND
Ground for outputs.
PWR
0.7V Power supply for outputs.
12
VDD_IO
13
SRC0/DOT96
O, DIF 100MHz Differential serial reference clocks/Fixed 96MHz clock output.
(Selected via I2C default is SRC0)
14
SRC0#/DOT96#
O, DIF 100MHz Differential serial reference clocks/Fixed 96MHz clock output.
(Selected via I2C default is SRC0)
15
VSS_IO
GND
Ground for PLL2.
PWR
3.3V Power supply for PLL3
16
VDD_PLL3
17
SRC1/LCD100/27_NSS
O, DIF, True 100 MHz differential serial reference clock output/True 100 MHz LCD video
SE
clock output / Non-spread 27-MHz video clock output.
Selected via GCLK_SEL at CKPWRGD assertion.
18
SRC1#/LCD100#/27_SS
O, DIF, Complementary 100 MHz differential serial reference clock output/Complementary
SE
100 MHz LCD video clock output /Spread 27 MHz video clock output.
Selected via GCLK_SEL at CKPWRGD assertion.
19
VSS_PLL3
20
21
GND
Ground for PLL3.
VDD_PLL3_IO
PWR
IO Power supply for PLL3 outputs.
SRC2/SATA
O, DIF 100MHz Differential serial reference clocks.
22
SRC2#/SATA#
O, DIF 100MHz Differential serial reference clocks.
23
VSS_SRC
24
SRC3/OE#_0/2_B
I/O,
Dif
100MHz Differential serial reference clocks / 3.3V OE#_0/2_B, input, mappable via
I2C to control either SRC0 or SRC2. (Default SRC3, 100MHz clock)
25
SRC3#OE#_1/4_B
I/O,
Dif
100MHz Differential serial reference clocks / 3.3V OE#_1/4_B input, mappable via
I2C to control either SRC1 or SRC4. (Default SRC3, 100MHz clock)
26
VDD_SRC_IO
GND
PWR
Ground for outputs.
IO power supply for SRC outputs.
........................ DOC #: SP-AP-0064 (Rev. AB) Page 2 of 28
SL28541-2
56 TSSOP Pin Definition (continued)
Pin No.
27
SRC4
Name
Type
Description
O, DIF 100MHz Differential serial reference clocks.
28
SRC4#
29
CPU_STP#
O, DIF 100MHz Differential serial reference clocks.
30
31
32
SRC6#
O, DIF 100MHz Differential serial reference clocks.
33
SRC6
O, DIF 100MHz Differential serial reference clocks.
34
VSS_SRC
35
SRC7#/OE#_6
I/O,
Dif
100MHz Differential serial reference clocks/3.3V OE#6 Input controlling SRC6.
(Default SRC7, 100MHz clock).
36
SRC7/OE#_8
I/O,
Dif
100MHz Differential serial reference clocks/3.3V OE#8 Input controlling SRC8.
(Default SRC7, 100MHz clock).
37
VDD_SRC_IO
PWR
38
SRC8#/CPU2#_ITP#
I
3.3V tolerant input for stopping CPU outputs
PCI_STP#
I
3.3V tolerant input for stopping PCI and SRC outputs
VDD_SRC
PWR
GND
3.3V Power supply for SRC PLL.
Ground for outputs.
0.7V power supply for SRC outputs.
O, DIF Selectable differential CPU or SRC clock output. ITP_EN = 0 at CKPWRGD
assertion = SRC8
ITP_EN = 1 @ CKPWRGD assertion = CPU2
(Note: CPU2 is an iAMT clock in iAMT mode depending on the configuration set in Byte 11
Bit3:2)
39
SRC8/CPU2_ITP
O, DIF Selectable differential CPU or SRC clock output. ITP_EN = 0 at CKPWRGD
assertion = SRC8
ITP_EN = 1 @ CKPWRGD assertion = CPU2
(Note: CPU2 is an iAMT clock in iAMT mode depending on the configuration set in Byte 11
Bit3:2)
40
NC
NC
PWR
No Connect
41
VDD_CPU_IO
42
CPU1#
O, DIF Differential CPU clock outputs. (Note: CPU1 is an iAMT clock in iAMT mode depending
IO Power supply for CPU outputs.
43
CPU1
O, DIF Differential CPU clock outputs. (Note: CPU1 is an iAMT clock in iAMT mode depending
44
VSS_CPU
45
CPU#0
O, DIF Differential CPU clock outputs.
46
CPU0
O, DIF Differential CPU clock outputs.
on the configuration set in Byte 11 Bit3:2)
on the configuration set in Byte 11 Bit3:2)
GND
PWR
Ground for outputs.
47
VDD_CPU
48
CKPWRGD/PD#
I
3.3V LVTTL input. This pin is a level sensitive strobe used to latch the FS_A, FS_B,
FS_C, FS_D, SRC5_SEL, and ITP_EN.
After CKPWRGD (active HIGH) assertion, this pin becomes a real-time input for
asserting power down (active LOW).
3.3V Power supply for CPU PLL.
49
FSB/TEST_MODE
I
3.3V tolerant input for CPU frequency selection.
Selects Ref/N or Tri-state when in test mode
0 = Tri-state, 1 = Ref/N.
Refer to DC Electrical Specifications table for Vil_FS and Vih_FS specifications.
50
VSS_REF
GND
51
XOUT
O, SE 14.318MHz Crystal output. (Float XOUT if using CLKIN)
52
XIN/CLKIN
I
53
VDD_REF
PWR
54
REF0/FSC/TEST_SEL
I/O
3.3V tolerant input for CPU frequency selection/fixed 14.318MHz clock output.
Selects test mode if pulled to VIHFS_C when CKPWRGD is asserted HIGH. Refer
to DC Electrical Specifications table for VILFS_C, VIMFS_C, VIHFS_C specifications.
55
SMB_DATA
I/O
SMBus compatible SDATA.
Ground for outputs.
14.318MHz Crystal input or 3.3V, 14.318MHz input clock signal.
3.3V Power supply for outputs and also maintains SMBUS registers during
power-down.
........................ DOC #: SP-AP-0064 (Rev. AB) Page 3 of 28
SL28541-2
56 TSSOP Pin Definition (continued)
Pin No.
Name
56
SMB_CLK
Type
I
Description
SMBus compatible SCLOCK.
Table 1. Frequency Select Pin (FSA, FSB and FSC)
FSC
FSB
FSA
CPU
0
0
0
266 MHz
0
0
1
133 MHz
0
1
0
200 MHz
0
1
1
166 MHz
1
0
0
333 MHz
1
0
1
100 MHz
1
1
0
400 MHz
1
1
1
Reserved
SRC
PCIF/PCI
27MHz
REF
DOT96
USB
100 MHz
33 MHz
27 MHz
14.318 MHz
96 MHz
48 MHz
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Frequency Select Pin (FSA, FSB and FSC)
Apply the appropriate logic levels to FSA, FSB, and FSC
inputs before CKPWRGD assertion to achieve host clock
frequency selection. When the clock chip sampled HIGH on
CKPWRGD and indicates that VTT voltage is stable then FSA,
FSB, and FSC input values are sampled. This process
employs a one-shot functionality and once the CKPWRGD
sampled a valid HIGH, all other FSA, FSB, FSC, and
CKPWRGD transitions are ignored except in test mode.
Serial Data Interface
To enhance the flexibility and function of the clock synthesizer,
a two-signal serial interface is provided. Through the Serial
Data Interface, various device functions, such as individual
clock output buffers are individually enabled or disabled. The
registers associated with the Serial Data Interface initialize to
their default setting at power-up. The use of this interface is
optional. Clock device register changes are normally made at
system initialization, if any are required. The interface cannot
be used during system operation for power management
functions.
Data Protocol
The clock driver serial protocol accepts byte write, byte read,
block write, and block read operations from the controller. For
block write/read operation, access the bytes in sequential
order from lowest to highest (most significant bit first) with the
ability to stop after any complete byte is transferred. For byte
write and byte read operations, the system controller can
access individually indexed bytes. The offset of the indexed
byte is encoded in the command code described in Table 2.
The block write and block read protocol is outlined in Table 3
while Table 4 outlines byte write and byte read protocol. The
slave receiver address is 11010010 (D2h).
.
Table 2. Command Code Definition
Bit
7
Description
0 = Block read or block write operation, 1 = Byte read or byte write operation
(6:0)
Byte offset for byte read or byte write operation. For block read or block write operations, these bits should be '0000000'
Table 3. Block Read and Block Write Protocol
Block Write Protocol
Bit
1
8:2
9
10
18:11
19
27:20
28
Description
Start
Slave address–7 bits
Write
Acknowledge from slave
Command Code–8 bits
Block Read Protocol
Bit
1
8:2
9
10
18:11
Description
Start
Slave address–7 bits
Write
Acknowledge from slave
Command Code–8 bits
Acknowledge from slave
19
Acknowledge from slave
Byte Count–8 bits
20
Repeat start
Acknowledge from slave
........................ DOC #: SP-AP-0064 (Rev. AB) Page 4 of 28
27:21
Slave address–7 bits
SL28541-2
Table 3. Block Read and Block Write Protocol (continued)
Block Write Protocol
Bit
36:29
37
45:38
Description
Data byte 1–8 bits
Acknowledge from slave
Data byte 2–8 bits
Block Read Protocol
Bit
Read = 1
29
Acknowledge from slave
37:30
46
Acknowledge from slave
....
Data Byte /Slave Acknowledges
....
Data Byte N–8 bits
....
Acknowledge from slave
....
Stop
Description
28
38
46:39
47
55:48
Byte Count from slave–8 bits
Acknowledge
Data byte 1 from slave–8 bits
Acknowledge
Data byte 2 from slave–8 bits
56
Acknowledge
....
Data bytes from slave / Acknowledge
....
Data Byte N from slave–8 bits
....
NOT Acknowledge
....
Stop
Table 4. Byte Read and Byte Write Protocol
Byte Write Protocol
Bit
1
8:2
9
10
18:11
19
27:20
Description
Start
Slave address–7 bits
Write
Acknowledge from slave
Command Code–8 bits
Byte Read Protocol
Bit
1
8:2
9
10
18:11
Description
Start
Slave address–7 bits
Write
Acknowledge from slave
Command Code–8 bits
Acknowledge from slave
19
Acknowledge from slave
Data byte–8 bits
20
Repeated start
28
Acknowledge from slave
29
Stop
27:21
28
29
37:30
........................ DOC #: SP-AP-0064 (Rev. AB) Page 5 of 28
Slave address–7 bits
Read
Acknowledge from slave
Data from slave–8 bits
38
NOT Acknowledge
39
Stop
SL28541-2
Control Registers
Byte 0: Control Register 0
Bit
@Pup
Name
Description
7
HW
FS_C
CPU Frequency Select Bit, set by HW
6
HW
FS_B
CPU Frequency Select Bit, set by HW
5
HW
FS_A
4
0
iAMT_EN
3
0
RESERVED
2
0
SRC_Main_SEL
1
0
SATA_SEL
Select source of SATA clock
0 = SATA = SRC_MAIN, 1= SATA = PLL2
0
1
PD_Restore
Save configuration when PD# is asserted
0 = Config. cleared, 1 = Config. saved
CPU Frequency Select Bit, set by HW
Set via SMBus or by combination of PWRDWN, CPU_STP, and PCI_STP
0 = Legacy Mode, 1 = iAMT Enabled
RESERVED
Select source for SRC clock
0 = SRC_MAIN = PLL1, PLL3_CFG Table applies
1 = SRC_MAIN = PLL3, PLL3_CFG Table does not apply
Byte 1: Control Register 1
Bit
@Pup
Name
7
0
SRC0_SEL
Description
6
0
PLL1_SS_DC
Select for down or center SS
0 = Down spread, 1 = Center spread
5
0
PLL3_SS_DC
Select for down or center SS
0 = Down spread, 1 = Center spread
4
0
PLL3_CFB3
3
0
PLL3_CFB2
2
1
PLL3_CFB1
1
0
PLL3_CFB0
0
1
RESERVED
Select for SRC0 or DOT96
0 = SRC0, 1 = DOT96
When GCLK_SEL=0, this bit is 1. When GCLK_SEL=1, this bit is 0
Bit 4:1 only applies when SRC_Main_SEL = 0
SeeTable 8: PLL3 / SE configuration table
RESERVED
Byte 2: Control Register 2
Bit
@Pup
Name
Description
7
1
REF
Output enable for REF
0 = Output Disabled, 1 = Output Enabled
6
1
USB
Output enable for USB
0 = Output Disabled, 1 = Output Enabled
5
1
PCIF0
Output enable for PCIF0
0 = Output Disabled, 1 = Output Enabled
4
1
PCI4
Output enable for PCI4
0 = Output Disabled, 1 = Output Enabled
3
1
PCI3
Output enable for PCI3
0 = Output Disabled, 1 = Output Enabled
2
1
PCI2
Output enable for PCI2
0 = Output Disabled, 1 = Output Enabled
1
1
PCI1
Output enable for PCI1
0 = Output Disabled, 1 = Output Enabled
0
1
PCI0
Output enable for PCI0
0 = Output Disabled, 1 = Output Enabled
........................ DOC #: SP-AP-0064 (Rev. AB) Page 6 of 28
SL28541-2
Byte 3: Control Register 3
Bit
@Pup
Name
7
1
RESERVED
RESERVED
Description
6
1
RESERVED
RESERVED
5
1
RESERVED
RESERVED
4
1
SRC[T/C]8/CPU2_ITP
Output enable for SRC8 or CPU2_ITP
0 = Output Disabled, 1 = Output Enabled
3
1
SRC[T/C]7
Output enable for SRC7
0 = Output Disabled, 1 = Output Enabled
2
1
SRC[T/C]6
Output enable for SRC6
0 = Output Disabled, 1 = Output Enabled
1
1
RESERVED
0
1
SRC[T/C]4
RESERVED
Output enable for SRC4
0 = Output Disabled, 1 = Output Enabled
Byte 4: Control Register 4
Bit
@Pup
Name
7
1
SRC[T/C]3
Output enable for SRC3
0 = Output Disabled, 1 = Output Enabled
Description
6
1
SRC[T/C]2/SATA
Output enable for SRC2/SATA
0 = Output Disabled, 1 = Output Enabled
5
1
4
1
SRC[T/C]0/DOT96[T/C]
Output enable for SRC0/DOT96
0 = Output Disabled, 1 = Output Enabled
3
1
CPU[T/C]1
Output enable for CPU1
0 = Output Disabled, 1 = Output Enabled
2
1
CPU[T/C]0
Output enable for CPU0
0 = Output Disabled, 1 = Output Enabled
1
1
PLL1_SS_EN
Enable PLL1s spread modulation,
0 = Spread Disabled, 1 = Spread Enabled
0
1
PLL3_SS_EN
Enable PLL3s spread modulation
0 = Spread Disabled, 1 = Spread Enabled
SRC[T/C]1/LCD_100M[T/C] Output enable for SRC1/LCD_100M
0 = Output Disabled, 1 = Output Enabled
Byte 5: Control Register 5
Bit
@Pup
Name
Description
7
0
CR#_A_EN
Enable CR#_A (clk req)
0 = Disabled, 1 = Enabled,
6
0
CR#_A_SEL
Set CR#_A SRC0 or SRC2
0 = CR#_ASRC0, 1 = CR#_ASRC2
5
0
CR#_B_EN
Enable CR#_B(clk req)
0 = Disabled, 1 = Enabled,
4
0
CR#_B_SEL
Set CR#_B SRC1 or SRC4
0 = CR#_BSRC1, 1 = CR#_BSRC4
3
0
CR#_C_EN
Enable CR#_C (clk req)
0 = Disabled, 1 = Enabled
2
0
CR#_C_SEL
Set CR#_C SRC0 or SRC2
0 = CR#_CSRC0, 1 = CR#_CSRC2
1
0
CR#_D_EN
Enable CR#_D (clk req)
0 = Disabled, 1 = Enabled
........................ DOC #: SP-AP-0064 (Rev. AB) Page 7 of 28
SL28541-2
Byte 5: Control Register 5 (continued)
Bit
@Pup
Name
0
0
CR#_D_SEL
Description
Set CR#_D SRC1 or SRC4
0 = CR#_DSRC1, 1 = CR#_DSRC4
Byte 6: Control Register 6
Bit
@Pup
Name
Description
7
0
CR#_E_EN
Enable CR#_E (clk req) SRC6
0 = Disabled, 1 = Enabled
6
0
CR#_F_EN
Enable CR#_F (clk req) SRC8
0 = Disabled, 1 = Enabled
5
0
RESERVED
RESERVED
4
0
RESERVED
RESERVED
3
0
RESERVED
RESERVED
2
0
RESERVED
RESERVED
1
0
LCD_100_STP_CTRL
If set, LCD_100 stop with PCI_STP#
0 = Free running, 1 = PCI_STP# stoppable
0
0
SRC_STP_CTRL
If set, SRCs stop with PCI_STP#
0 = Free running, 1 = PCI_STP# stoppable
Byte 7: Vendor ID
Bit
@Pup
Name
7
0
Rev Code Bit 3
Revision Code Bit 3
Description
6
0
Rev Code Bit 2
Revision Code Bit 2
5
0
Rev Code Bit 1
Revision Code Bit 1
4
1
Rev Code Bit 0
Revision Code Bit 0
3
1
Vendor ID bit 3
Vendor ID Bit 3
2
0
Vendor ID bit 2
Vendor ID Bit 2
1
0
Vendor ID bit 1
Vendor ID Bit 1
0
0
Vendor ID bit 0
Vendor ID Bit 0
Byte 8: Control Register 8
Bit
@Pup
Name
7
0
Device_ID3
Description
6
0
Device_ID2
5
0
Device_ID1
4
0
Device_ID0
3
0
Reserved
Reserved
2
0
Reserved
Reserved
0000 = CK505 Yellow Cover Device, 56-pin TSSOP
0001 = CK505 Yellow Cover Device, 64-pin TSSOP
0010 = CK505 Yellow Cover Device, 48-pin QFN (Reserved)
0011 = CK505 Yellow Cover Device, 56-pin QFN (Reserved)
0100 = CK505 Yellow Cover Device, 64-pin QFN
0101 = CK505 Yellow Cover Device, 72-pin QFN (Reserved)
0110 = CK505 Yellow Cover Device, 48-pin SSOP (Reserved)
0111 = CK505 Yellow Cover Device, 48-pin SSOP (Reserved)
1000 = Reserved
1001 = CY28548
1010 = Reserved
1011 = Reserved
1100 = Reserved
1101 = Reserved
1110 = Reserved
1111 = Reserved
........................ DOC #: SP-AP-0064 (Rev. AB) Page 8 of 28
SL28541-2
Byte 8: Control Register 8 (continued)
Bit
@Pup
Name
Description
1
1
27M_NSS_OE
Output enable for 27M_NSS
0 = Output Disabled, 1 = Output Enabled
0
1
27M_SS_OE
Output enable for 27M_SS
0 = Output Disabled, 1 = Output Enabled
Byte 9: Control Register 9
Bit
@Pup
Name
Description
7
0
PCIF_0_with PCI_STP#
6
HW
TME_STRAP
5
1
REF_DSC1
4
0
TEST_MODE_SEL
Mode select either REF/N or tri-state
0 = All output tri-state, 1 = All output REF/N
3
0
TEST_MODE_ENTRY
Allow entry into test mode
0 = Normal operation, 1 = Enter test mode
2
1
I2C_VOUT
1
0
I2C_VOUT
0
1
I2C_VOUT
Allows control of PCIF_0 with assertion of PCI_STP#
0 = Free running PCIF, 1 = Stopped with PCI_STP#
Trusted mode enable strap status
0 = Normal, 1 = No overclocking
REF drive strength 1 of 2 (See Byte 17 and 18 for more setting)
0 = Low, 1 = High
Differential Amplitude Configuration
I2C_VOUT[2,1,0]
000 = 0.63V
001 = 0.71V
010 = 0.77V
011 = 082V
100 = 0.86V
101 = 0.90V (default)
110 = 0.93V
111 = unused
Byte 10: Control Register 10
Bit
@Pup
Name
Description
7
HW
GCLK_SEL latch
6
1
PLL3_EN
PLL3 power down
0 = Power down, 1 = Power up
5
1
PLL2_EN
PLL2 power down
0 = Power down, 1 = Power up
4
1
SRC_DIV_EN
SRC divider disable
0 = Disabled, 1 = Enabled
3
1
PCI_DIV_EN
PCI divider disable
0 = Disabled, 1 = Enabled
2
1
CPU_DIV_EN
CPU divider disable
0 = Disabled, 1 = Enabled
1
1
CPU1 Stop Enable
Enable CPU_STP# control of CPU1
0 = Free running, 1= Stoppable
0
1
CPU0 Stop Enable
Enable CPU_STP# control of CPU0
0 = Free running, 1= Stoppable
Readback of GCLK_SEL latch
0 = DOT96/LCD_100, 1 = SRC0/27 MHz
Byte 11: Control Register 11
Bit
@Pup
Name
7
0
Reserved
Description
Reserved
........................ DOC #: SP-AP-0064 (Rev. AB) Page 9 of 28
SL28541-2
Byte 11: Control Register 11 (continued)
6
0
Reserved
Reserved
5
0
Reserved
Reserved
4
0
Reserved
Reserved
3
0
Reserved
Reserved
2
0
Reserved
Reserved
1
0
Reserved
Reserved
0
0
Reserved
Reserved
Byte 12: Byte Count
Bit
@Pup
Name
Description
7
0
Reserved
Reserved
6
0
Reserved
Reserved
5
0
BC5
4
1
BC4
3
0
BC3
2
0
BC2
1
1
BC1
0
1
BC0
Byte count register for block read operation.
The default value for Byte count is 19.
In order to read beyond Byte 19, the user should change the byte count
limit.to or beyond the byte that is desired to be read.
Byte 13: Control Register 13
Bit
@Pup
Name
7
1
USB_BIT1
Description
6
1
PCI/ PCIF_BIT1
5
0
PLL1_Spread
Select percentage of spread for PLL1
0 = 0.5%, 1=1%
4
1
SATA_SS_EN
Enable SATA spread modulation,
0 = Spread Disabled, 1 = Spread Enabled
3
1
CPU[T/C]2
2
1
SE1/SE2_BIT_1
1
1
Reserved
Reserved
0
1
SW_PCI
SW PCI_STP# Function
0 = SW PCI_STP assert, 1 = SW PCI_STP deassert
When this bit is set to 0, all STOPPABLE PCI, PCIF and SRC outputs are
stopped in a synchronous manner with no short pulses.
When this bit is set to 1, all STOPPED PCI, PCIF and SRC outputs are
resumed in a synchronous manner with no short pulses.
Name
Description
USB drive strength 1 of 3(See Byte 17 for more setting)
0 = Low, 1= High
PCI drive strength 1 of 3(See Byte 17 & 18 for more setting)
0 = Low, 1 = High
Allow control of CPU2 with assertion of CPU_STP#
0 = Free running, 1 = Stopped with CPU_STP#
SE1 and SE2 Drive Strength Setting 1 of 3 (See Byte 17 and 18 for more setting)
0 = Low, 1= High
Byte 14: Control Register 14
Bit
@Pup
...................... DOC #: SP-AP-0064 (Rev. AB) Page 10 of 28
SL28541-2
Byte 14: Control Register 14
7
0
CPU_DAF_N7
6
0
CPU_DAF_N6
5
0
CPU_DAF_N5
4
0
CPU_DAF_N4
3
0
CPU_DAF_N3
2
0
CPU_DAF_N2
1
0
CPU_DAF_N1
0
0
CPU_DAF_N0
If Prog_CPU_EN is set, the values programmed in CPU_DAF_N[8:0] and
CPU_DAF_M[6:0] are used to determine the CPU output frequency.
Byte 15: Control Register 15
Bit
@Pup
Name
7
0
CPU_DAF_N8
See Byte 14 for description
If Prog_CPU_EN is set, the values programmed in CPU_DAF_N[8:0] and
CPU_DAF_M[6:0] are used to determine the CPU output frequency.
6
0
CPU_DAF_M6
5
0
CPU_DAF_M5
4
0
CPU_DAF_M4
3
0
CPU_DAF_M3
2
0
CPU_DAF_M2
1
0
CPU_DAF_M1
0
0
CPU_DAF_M0
Description
Byte 16: Control Register 16
Bit
@Pup
Name
Description
Dial-A-Frequency®
7
0
PCI-E_N7
PCI-E
6
0
PCI-E_N6
PCI-E Dial-A-Frequency Bit N6
5
0
PCI-E_N5
PCI-E Dial-A-Frequency Bit N5
4
0
PCI-E_N4
PCI-E Dial-A-Frequency Bit N4
3
0
PCI-E_N3
PCI-E Dial-A-Frequency Bit N3
2
0
PCI-E_N2
PCI-E Dial-A-Frequency Bit N2
1
0
PCI-E_N1
PCI-E Dial-A-Frequency Bit N1
0
0
PCI-E_N0
PCI-E Dial-A-Frequency Bit N0
...................... DOC #: SP-AP-0064 (Rev. AB) Page 11 of 28
Bit N7
SL28541-2
Byte 17: Control Register 17
Bit
@Pup
Name
7
0
SMSW_EN
Enable Smooth Switching
0 = Disabled, 1= Enabled
Description
6
0
SMSW_SEL
Smooth switch select
0 = CPU_PLL, 1 = SRC_PLL
5
0
SE1/SE2_BIT0
SE1 and SE2 drive strength Setting 2 of 3(see Byte 18 for more setting)
0 = Low, 1= High
4
0
Prog_PCI-E_EN
Programmable PCI-E frequency enable
0 = Disabled, 1= Enabled
3
0
Prog_CPU_EN
Programmable CPU frequency enable
0 = Disabled, 1= Enabled
2
0
REF_BIT0
REFdrive strength strength Setting 2 of 3(see Byte 18 for more setting)
0 = Low, 1= High
1
0
USB_BIT0
USB drive strength strength Setting 2 of 3(see Byte 18 for more setting)
0 = Low, 1= High
0
0
PCI/ PCIF_BIT0
PCI drive strength strength Setting 2 of 3(see Byte 18 for more setting)
0 = Low, 1= High
Byte 18: Control Register 18
7
0
REF_BIT2
6
0
RESERVED
5
1
RESERVED
4
0
RESERVED
Drive Strength Control
3
0
USB_BIT2
1
BIT_0
(Byte 17)
1
2
0
PCI/PCIF_BIT2
1
1
0
1
0
SE1/SE2_BIT2
1
0
1
RESERVED
1
0
0
0
1
1
0
1
0
0
0
1
0
0
Def ault
BIT_2
(Byte18)
1
(Vario us B ytes )
BIT_1
Buf f er
Strength
Strongest
Table 5. Output Driver Status during PCI-STP# and CPU-STP#
PCI_STP# Asserted
Single-ended Clocks Stoppable
Differential Clocks
CPU_STP# Asserted
Driven low
Running
Non stoppable
Running
Running
Stoppable
Clock driven high
Clock driven high
Non stoppable
Clock# driven low
Clock# driven low
Running
Running
SMBus OE Disabled
Driven low
Clock driven Low or 20K
pulldown
Table 6. Output Driver Status
All Single-ended Clocks
w/o Strap
All Differential Clocks except
CPU1
w/ Strap
Clock
Clock#
CPU1
Clock
Clock#
Latches Open State
Low
Hi-z
Low or 20K pulldown Low
Low or 20K pulldown Low
Powerdown
Low
Hi-z
Low or 20K pulldown Low
Low or 20K pulldown Low
M1
Low
Hi-z
Low or 20K pulldown Low
Running
...................... DOC #: SP-AP-0064 (Rev. AB) Page 12 of 28
Running
SL28541-2
Table 7. PLL3/SE Configuration Table
GCLK_SEL
B1b4
B1b3
B1b2
B1b1
0
0
0
0
0
Pin 17 (MHz)
Pin 18 (MHz)
Spread (%)
Comment
0
0
0
0
1
100
100
0.5
SRC1 from SRC_Main
0
0
0
1
0
100
100
0.5
LCD_100 from PLL3
0
0
0
1
1
100
100
1
LCD_100 from PLL3
0
0
1
0
0
100
100
1.5
LCD_100 from PLL3
0
0
1
0
1
100
100
2
LCD_100 from PLL3
0
0
1
1
0
N/A
N/A
N/A
N/A
0
0
1
1
1
N/A
N/A
N/A
N/A
0
1
0
0
0
N/A
N/A
N/A
N/A
0
1
0
0
1
N/A
N/A
N/A
N/A
0
1
0
1
0
N/A
N/A
N/A
N/A
0
1
0
1
1
N/A
N/A
N/A
N/A
0
1
1
0
0
N/A
N/A
none
N/A
0
1
1
0
1
N/A
N/A
N/A
N/A
0
1
1
1
0
N/A
N/A
N/A
N/A
0
1
1
1
1
N/A
N/A
N/A
N/A
1
0
0
0
0
N/A
N/A
N/A
1
0
0
0
1
27M_NSS
27M_SS
0.5
1
0
0
1
0
27M_NSS
27M_SS
0.5
27M_SS from PLL3
1
0
0
1
1
27M_NSS
27M_SS
1
27M_SS from PLL3
1
0
1
0
0
27M_NSS
27M_SS
1.5
27M_SS from PLL3
1
0
1
0
1
27M_NSS
27M_SS
2
27M_SS from PLL3
1
0
1
1
0
N/A
N/A
N/A
1
0
1
1
1
N/A
N/A
N/A
1
1
0
0
0
N/A
N/A
N/A
1
1
0
0
1
N/A
N/A
N/A
1
1
0
1
0
N/A
N/A
N/A
1
1
0
1
1
N/A
N/A
N/A
1
1
1
0
0
N/A
N/A
N/A
1
1
1
0
1
N/A
N/A
N/A
PLL3 Disabled
27M_SS from PLL3
Table 8. Crystal Recommendations
Frequency
(Fund)
Cut
Loading Load Cap
Drive
(max.)
Shunt Cap
(max.)
Motional
(max.)
Tolerance
(max.)
Stability
(max.)
Aging
(max.)
14.31818 MHz
AT
Parallel
0.1 mW
5 pF
0.016 pF
35 ppm
30 ppm
5 ppm
20 pF
Crystal Loading
The SL28541-2 requires a Parallel Resonance Crystal. Substituting a series resonance crystal causes the SL28541-2 to
operate at the wrong frequency and violates the ppm specification. For most applications there is a 300-ppm frequency
shift between series and parallel crystals due to incorrect
loading.
...................... DOC #: SP-AP-0064 (Rev. AB) Page 13 of 28
Crystal loading plays a critical role in achieving low ppm performance. To realize low ppm performance, use the total capacitance the crystal sees to calculate the appropriate capacitive
loading (CL).
Figure 1 shows a typical crystal configuration using the two
trim capacitors. It is important that the trim capacitors are in
series with the crystal. It is not true that load capacitors are in
parallel with the crystal and are approximately equal to the
load capacitance of the crystal.
SL28541-2
Dial-A-Frequency® (CPU and SRC Clocks)
This feature allows the user to over-clock their system by
slowly stepping up the CPU or SRC frequency. When the
programmable output frequency feature is enabled, the CPU
and SRC frequencies are determined by the following
equation:
Fcpu = G * N/M or Fcpu=G2 * N, where G2 = G / M.
• “N” and “M” are the values programmed in Programmable
Frequency Select N-Value Register and M-Value Register,
respectively.
Figure 1. Crystal Capacitive Clarification
Calculating Load Capacitors
In addition to the standard external trim capacitors, consider
the trace capacitance and pin capacitance to calculate the
crystal loading correctly. Again, the capacitance on each side
is in series with the crystal. The total capacitance on both side
is twice the specified crystal load capacitance (CL). Trim
capacitors are calculated to provide equal capacitive loading
on both sides.
• “G” stands for the PLL Gear Constant, which is determined
by the programmed value of FS[E:A]. See Table 1,
Frequency Select Table for the Gear Constant for each
Frequency selection. The PCI Express only allows user
control of the N register, the M value is fixed and
documented in Table 1, Frequency Select Table.
In this mode, the user writes the desired N and M values into
the DAF I2C registers. The user cannot change only the M
value and must change both the M and the N values at the
same time, if they require a change to the M value. The user
may change only the N value.
Associated Register Bits
• CPU_DAF Enable – This bit enables CPU DAF mode. By
default, it is not set. When set, the operating frequency is
determined by the values entered into the CPU_DAF_N
register. Note that the CPU_DAF_N and M register must
contain valid values before CPU_DAF is set. Default = 0,
(No DAF).
• CPU_DAF_N – There are nine bits (for 512 values) to
linearly change the CPU frequency (limited by VCO range).
Default = 0, (0000). The allowable values for N are detailed
in Table 1, Frequency Select Table.
• CPU DAF M – There are 7 bits (for 128 values) to linearly
change the CPU frequency (limited by VCO range). Default
= 0, the allowable values for M are detailed in Table 1,
Frequency Select Table
Figure 2. Crystal Loading Example
,
Use the following formulas to calculate the trim capacitor
values for Ce1 and Ce2.
Load Capacitance (each side)
Ce = 2 * CL – (Cs + Ci)
Total Capacitance (as seen by the crystal)
CLe
=
1
1
( Ce1 + Cs1
+ Ci1 +
1
Ce2 + Cs2 + Ci2
)
• SRC_DAF Enable – This bit enables SRC DAF mode. By
default, it is not set. When set, the operating frequency is
determined by the values entered into the SRC_DAF_N
register. Note that the SRC_DAF_N register must contain
valid values before SRC_DAF is set. Default = 0, (No DAF).
• SRC_DAF_N – There are nine bits (for 512 values) to
linearly change the CPU frequency (limited by VCO range).
Default = 0, (0000). The allowable values for N are detailed
in Table 1, Frequency Select Table.
Smooth Switching
CL ................................................... Crystal load capacitance
CLe .........................................Actual loading seen by crystal
using standard value trim capacitors
Ce .....................................................External trim capacitors
Cs ............................................. Stray capacitance (terraced)
Ci .......................................................... Internal capacitance
(lead frame, bond wires, etc.)
The device contains one smooth switch circuit that is shared
by the CPU PLL and SRC PLL. The smooth switch circuit
ensures that when the output frequency changes by
overclocking, the transition from the old frequency to the new
frequency is a slow, smooth transition containing no glitches.
The rate of change of output frequency when using the smooth
switch circuit is less than 1 MHz/0.667 s. The frequency
overshoot and undershoot is less than 2%.
The Smooth Switch circuit assigns auto or manual. In Auto
mode, clock generator assigns smooth switch automatically
when the PLL does overclocking. For manual mode, assign
...................... DOC #: SP-AP-0064 (Rev. AB) Page 14 of 28
SL28541-2
the smooth switch circuit to PLL via Smbus. By default the
smooth switch circuit is set to auto mode. PLL can be
over-clocked when it does not have control of the smooth
switch circuit but it is not guaranteed to transition to the new
frequency without large frequency glitches.
Do not enable over-clocking and change the N values of both
PLLs in the same SMBUS block write and use smooth switch
mechanism on spread spectrum on/off.
PD_RESTORE
If a ‘0’ is set for Byte 0 bit 0 then, upon assertion of PD# LOW,
the SL28541-2 initiates a full reset. The result of this is that the
clock chip emulates a cold power on start and goes to the
“Latches Open” state. If the PD_RESTORE bit is set to a ‘1’
then the configuration is stored upon PD# asserted LOW. Note
that if the iAMT bit, Byte 0 bit 3, is set to a ‘1’ then the
PD_RESTORE bit must be ignored. In other words, in Intel
iAMT mode, PD# reset is not allowed.
PD# (Power down) Clarification
PD# (Power down) Assertion
When PD is sampled HIGH by two consecutive rising edges
of CPUC, all single-ended outputs will be held LOW on their
next HIGH-to-LOW transition and differential clocks must held
LOW. When PD mode is desired as the initial power on state,
PD must be asserted HIGH in less than 10 s after asserting
CKPWRGD.
PD# Deassertion
The power up latency is less than 1.8 ms. This is the time from
the deassertion of the PD# pin or the ramping of the power
supply until the time that stable clocks are generated from the
clock chip. All differential outputs stopped in a three-state
condition, resulting from power down are driven high in less
than 300 s of PD# deassertion to a voltage greater than
200 mV. After the clock chip’s internal PLL is powered up and
locked, all outputs are enabled within a few clock cycles of
each clock. Figure 4 is an example showing the relationship of
clocks coming up.
The CKPWRGD/PD# pin is a dual-function pin. During initial
power up, the pin functions as CKPWRGD. Once CKPWRGD
has been sampled HIGH by the clock chip, the pin assumes
PD# functionality. The PD# pin is an asynchronous active
LOW input used to shut off all clocks cleanly before shutting
off power to the device. This signal is synchronized internally
to the device before powering down the clock synthesizer. PD#
is also an asynchronous input for powering up the system.
When PD# is asserted LOW, clocks are driven to a LOW value
and held before turning off the VCOs and the crystal oscillator.
PD#
CPUT, 133MHz
CPUC, 133MHz
SRCT 100MHz
SRCC 100MHz
USB, 48MHz
DOT96T
DOT96C
PCI, 33 MHz
REF
Figure 3. Power down Assertion Timing Waveform
...................... DOC #: SP-AP-0064 (Rev. AB) Page 15 of 28
SL28541-2
Ts ta b le
< 1 .8 m s
PD#
C P U T , 1 3 3 MH z
C P U C , 1 3 3 MH z
S R C T 1 0 0 MH z
S R C C 1 0 0 MH z
U S B , 4 8 MH z
D OT 9 6 T
D OT 9 6 C
P C I, 3 3 MH z
Td r iv e _ PW R D N #
2 00m V
REF
Figure 4. Power down Deassertion Timing Waveform
FS _A, FS _B ,FS_C ,FS _D
CKPWRGD
P W R G D _V R M
0.2-0.3 m s
D elay
V D D C lock G en
C lock S tate
C lock O utputs
C lock V C O
S tate 0
W ait for
V TT_PW R G D #
S tate 1
D evice is not affected,
V TT_P W R G D # is ignored
S am ple S els
State 2
O ff
State 3
On
On
O ff
Figure 5. CKPWRGD Timing Diagram
...................... DOC #: SP-AP-0064 (Rev. AB) Page 16 of 28
SL28541-2
CPU_STP# Assertion
CPU_STP# Deassertion
The CPU_STP# signal is an active LOW input used for
synchronous stopping and starting the CPU output clocks
while the rest of the clock generator continues to function.
When the CPU_STP# pin is asserted, all CPU outputs that are
set with the SMBus configuration to be stoppable are stopped
within two to six CPU clock periods after sampled by two rising
edges of the internal CPUC clock. The final states of the
stopped CPU signals are CPUT = HIGH and CPUC = LOW.
The deassertion of the CPU_STP# signal causes all stopped
CPU outputs to resume normal operation in a synchronous
manner. No short or stretched clock pulses are produced when
the clock resumes. The maximum latency from the
deassertion to active outputs is no more than two CPU clock
cycles.
CPU_STP#
CPUT
CPUC
Figure 6. CPU_STP# Assertion Waveform
CPU_STP#
CPUT
CPUC
CPUT Internal
CPUC Internal
Tdrive_CPU_STP#,10 ns>200 mV
Figure 7. CPU_STP# Deassertion Waveform
PCI_STP# Assertion
.
The PCI_STP# signal is an active LOW input used for
synchronously stopping and starting the PCI outputs while the
rest of the clock generator continues to function. The set-up
time for capturing PCI_STP# going LOW is 10 ns (tSU). (See
Figure 8.) The PCIF clocks are affected by this pin if their
corresponding control bit in the SMBus register is set to allow
them to be free running.
T su
PC I_STP#
PC I_F
PC I
SR C 100M H z
Figure 8. PCI_STP# Assertion Waveform
...................... DOC #: SP-AP-0064 (Rev. AB) Page 17 of 28
SL28541-2
.
PCI_STP# Deassertion
The deassertion of the PCI_STP# signal causes all PCI and
stoppable PCIF clocks to resume running in a synchronous
manner within two PCI clock periods, after PCI_STP# transitions to a HIGH level.
T su
T drive_ S R C
P C I_S T P #
P C I_F
PCI
SR C 100 M H z
Figure 9. PCI_STP# Deassertion Waveform
.
.
Figure 10. Clock Generator Power up/Run State Diagram
...................... DOC #: SP-AP-0064 (Rev. AB) Page 18 of 28
SL28541-2
Clock Off to M 1
3.3V
Vcc
2.0V
FSC
T_delay t
CPU_STP#
FSB
FSA
PCI_STP#
CKPWRGD/PD#
Off
CK505 SMBUS
CK505 State
Latches Open
Off
M1
BSEL[0..2]
CK505 Core Logic
Off
PLL1
Locked
CPU1
PLL2 & PLL3
All Other Clocks
REF Oscillator
T_delay2
T_delay3
Figure 11. BSEL Serial Latching
...................... DOC #: SP-AP-0064 (Rev. AB) Page 19 of 28
SL28541-2
Absolute Maximum Conditions
Parameter
Description
Condition
VDD_3.3V
Supply Voltage
Functional
VDD_IO
IO Supply Voltage
Functional
VIN
Input Voltage
Relative to VSS
TS
Temperature, Storage
Non-functional
TA
Commercial Temperature,
Operating Ambient
Functional
Min.
Max.
–
Industrial Temperature,
Operating Ambient
Unit
4.6
V
3.465
V
–0.5
4.6
VDC
–65
150
°C
0
85
°C
-40
+85
°C
TJ
Temperature, Junction
Functional
–
150
°C
ØJC
Dissipation, Junction to Case
JEDEC (JESD 51)
–
20
°C/W
ØJA
Dissipation, Junction to Ambient JEDEC (JESD 51)
–
60
°C/
W
ESDHBM
ESD Protection (Human Body
Model)
JEDEC (JESD 22-A114)
2000
–
V
UL-94
Flammability Rating
UL (CLASS)
MSL
Moisture Sensitivity Level
V–0
1
Multiple Supplies: The Voltage on any input or I/O pin cannot exceed the power pin during power-up. Power supply sequencing is NOT required.
DC Electrical Specifications
Parameter
Description
VDD core
3.3V Operating Voltage
Condition
3.3 ± 5%
Min.
Max.
Unit
3.135
3.465
V
VIH
3.3V Input High Voltage (SE)
2.0
VDD + 0.3
V
VIL
3.3V Input Low Voltage (SE)
VSS – 0.3
0.8
V
VIHI2C
Input High Voltage
SDATA, SCLK
2.2
–
V
VILI2C
Input Low Voltage
SDATA, SCLK
–
1.0
V
VIH_FS
FS_[A,B] Input High Voltage
0.7
1.5
V
VIL_FS
FS_[A,B] Input Low Voltage
VSS – 0.3
0.35
V
VIHFS_C_TEST
FS_C Input High Voltage
VIMFS_C_NORMAL FS_C Input Middle Voltage
VILFS_C_NORMAL FS_C Input Low Voltage
IIH
Input High Leakage Current
Except internal pull-down resistors, 0 < VIN < VDD
Except internal pull-up resistors, 0 < VIN < VDD
IIL
Input Low Leakage Current
VOH
3.3V Output High Voltage (SE) IOH = –1 mA
VOL
3.3V Output Low Voltage (SE)
VDD IO
Low Voltage IO Supply Voltage
IOZ
IOL = 1 mA
2
VDD + 0.3
V
0.7
1.5
V
VSS – 0.3
0.35
V
–
5
A
–5
–
A
2.4
–
V
–
0.4
V
1
3.465
V
High-impedance Output
Current
–10
10
A
CIN
Input Pin Capacitance
1.5
5
pF
COUT
Output Pin Capacitance
6
pF
LIN
Pin Inductance
–
7
nH
VXIH
Xin High Voltage
0.7VDD
VDD
V
VXIL
Xin Low Voltage
0
0.3VDD
V
IDDPWRDWN
Power Down Current
1
mA
IDD
Dynamic Supply Current
250
mA
...................... DOC #: SP-AP-0064 (Rev. AB) Page 20 of 28
–
SL28541-2
AC Electrical Specifications
Parameter
Description
Condition
Min.
Max.
Unit
47.5
52.5
%
69.841
71.0
ns
–
10.0
ns
Crystal
TDC
XIN Duty Cycle
The device operates reliably with input
duty cycles up to 30/70 but the REF clock
duty cycle will not be within specification
TPERIOD
XIN Period
When XIN is driven from an external
clock source
TR/TF
XIN Rise and Fall Times
Measured between 0.3VDD and 0.7VDD
TCCJ
XIN Cycle to Cycle Jitter
As an average over 1-s duration
LACC
Long-term Accuracy
–
500
ps
–
300
ppm
Measured at VDD/2
47
53
%
Clock Input
TDC
CLKIN Duty Cycle
TR/TF
CLKIN Rise and Fall Times
Measured between 0.2VDD and 0.8VDD
0.5
4.0
V/ns
TCCJ
CLKIN Cycle to Cycle Jitter
Measured at VDD/2
–
250
ps
TLTJ
CLKIN Long Term Jitter
Measured at VDD/2
–
350
ps
VIL
Input Low Voltage
XIN / CLKIN pin
–
0.8
V
VIH
Input High Voltage
XIN / CLKIN pin
2
VDD+0.3
V
IIL
Input LowCurrent
XIN / CLKIN pin, 0 < VIN
工商网监
湘ICP备2023018690号
