SL28647BLC

SL28647 Clock Generator for Intel®CK505 Features • 100-MHz low power spreadable differential video clock • 33-MHz PCI clocks • Compliant to Intel® CK505 • Buffered Reference Clock 14.318 MHz • Selectable CPU frequencies • Low-voltage frequency select inputs • Low power differential CPU clock pairs • I2C support with readback capabilities • 100-MHz low power differential SRC clocks • 96-MHz low power differential dot clock • Ideal Lexmark Spread Spectrum profile for maximum electromagnetic interference (EMI) reduction • 27-MHz Spread and Non-spread video clock • 3.3V power supply • 48-MHz USB clock • 72-pin QFN package • SRC clocks independently stoppable through CLKREQ#[1:9] Table 1. Output Confguration Table CPU SRC PCI REF DOT96 USB_48M LCD 27M x2/x3 x9/11 x5 x2 x1 x1 x1 x2 Block Diagram CLKREQ9# CLKREQ8# SRCT_8 SRCC_8 VSS_SRC SRCC_7 SRCT_7 VDD_SRC SRCC_6 SRCT_6 CLKREQ6# SCRC_5 SRCT_5 SCRC_4 SRCT_4 CLKREQ4# SRCC_3 SRCT_3 Pin Configuration 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 VDD_SRC SRCC_9 SRCT_9 VSS_SRC CPUC2_ITP / SRCC_10 CPUT2_ITP / SRCT_10 VDDA VSSA NC CPUC1_MCH CPUT1_MCH VDD_CPU CPUC0 CPUT0 VSS_CPU SCLK SDATA VDD_REF 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 SL28647 VDD_SRC SRCC_2 SRCT_2 SRCC_1/SATAC SRCT_1/SATAT VDD_SRC SRCC_0 / LCDC100 / 96C SRCT_0 / LCDT100 / 96T CLKREQ1# FSB/TEST_MODE DOT96C / 27M_SS DOT96T / 27M_NSS VSS_48 48M / FSA VDD_48 CKPWRGD/PD# CLKREQ7# PCIF0/ITP_SEL XOUT XIN VSS_REF REF1 REF0 / FSC_TEST_SEL CPU_STP# PCI_STP# CLKREQ2# PCI1 CLKREQ3# CLKREQ5# VDD_PCI VSS_PCI PCI2/TME PCI3 PCI4 / FCTSEL1 VSS_PCI VDD_PCI 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 ....................... Document #: 001-05103 Rev *B Page 1 of 27 400 West Cesar Chavez, Austin, TX 78701 1+(512) 416-8500 1+(512) 416-9669 www.silabs.com SL28647 Pin Description Pin No. Name 1, 49, 54, 65 VDD_SRC 2, 3, 52, 53, 55, 56, 58, 59, 60, 61, 63, 64, 66, 67, 69, 70 SRCT/C[2:9] Type PWR Description 3.3V power supply for outputs. O, DIF 100-MHz Differential serial reference clocks. 4, 68 VSS_SRC 5, 6 CPUT2_ITP/SRCT10, O, DIF Selectable differential CPU or SRC clock output. CPUC2_ITP/SRCC10 ITP_SEL = 0 @ pin 39 assertion = SRC10 ITP_SEL = 1 @ pin 39 assertion = CPU2 GND Ground for outputs. 7 VDDA PWR 3.3V power supply for PLL. 8 VSSA GND Ground for PLL. 9 NC NC No Connect Pin 10, 11 CPUC1_MCH, CPUT1_MCH 12 VDD_CPU O, DIF Differential CPU clock output to MCH PWR 3.3V power supply for outputs. 13, 14 CPU[T/C]0 15 VSS_CPU O, DIF Differential CPU clock output 16 SCLK 17 SDATA 18 VDD_REF PWR 19 XOUT O, SE 14.318-MHz crystal output. 20 XIN 21 VSS_REF GND I Ground for outputs. SMBus-compatible SCLOCK. I/O, OD SMBus-compatible SDATA. I GND 3.3V power supply for outputs. 14.318-MHz crystal input. Ground for outputs. 22 REF1 O Fixed 14.318-MHz clock output. 23 REF0/FSC_TESTSEL I/O Fixed 14.318 clock output/3.3V-tolerant input for CPU frequency selection/Selects test mode if pulled to VIMFS_C when pin 39 is asserted LOW. Refer to DC Electrical Specifications table for VILFS_C,VIMFS_C,VIHFS_C specifications. 24 CPU_STP# I 3.3V LVTTL input for CPU_STP# active LOW During direct clock off to M1 mode transition, a serial load of BSEL data is driven on this pin and sampled on the rising edge of PCI_STP#. See Figure 14.for more information. 25 PCI_STP# I 3.3V LVTTL input for PCI_STP# active LOW During direct clock off to M1 mode transition, a serial load of BSEL data is driven on CPU_STP# and sampled on the rising edge of this pin. See Figure 14. for more information. 26, 28, 29, 38, 46, 57, 62, 71, 72 CLKREQ[1:9]# I 3.3V LVTTL input for enabling assigned SRC clock (active LOW). 27 PCI1 30, 36 VDD_PCI PWR 3.3V power supply for outputs. 31, 35 VSS_PCI GND Ground for outputs. I/O, SE 33MHz clock output .......................Document #: 001-05103 Rev *B Page 2 of 27 SL28647 Pin Description (continued) Pin No. Name 32 PCI2/TME 33 PCI3 34 PCI4/FCTSEL1 Type Description I/O, PU, 33-MHz clock output/Trusted Mode Enable Strap SE Strap at pin 39 assertion to determine if the part is in trusted mode or not. Internal pull-up resistor of 100K to 3.3V, use 10K resistor to pull it low externally if needed 0 = Normal mode 1= Trusted mode (default) O, SE 33MHz clock output / 3.3V-tolerant input select pin to select termination scheme for differential clocks. I/O, PD 33-MHz clock output/3.3V LVTTL input for selecting pins 47,48 (SRC[T/C]0, 100M[T/C]) and pins 43,44 (DOT96[T/C] and 27M Spread and Non-spread) (sampled on pin 39 assertion). Internal pull-down resistor of 100K to GND FCTS E L1 P in 43 37 ITP_SEL/PCIF0 39 CKPWRGD/PD# P in 44 P in 47 P in 48 0 DOT96T DOT96C 96/100M_T 96/100M_C 1 27M_NSS 27M_SS SRCT0 SRCC0 I/O, PD, 3.3V LVTTL input to enable SRC10 or CPU2_ITP/33-MHz clock output. (sampled SE on pin 39 assertion). Internal pull-down resistor of 100K to GND 1 = CPU2_ITP, 0 = SRC10 I 3.3V LVTTL input. This pin is a level sensitive strobe. When asserted, it latches data on the FSA, FSB, FSC, FCTSEL1 and ITP_SEL pins. After assertion, it becomes a real time input for controlling power down. 40 VDD_48 PWR 41 48M/FSA I/O 3.3V power supply for outputs. 42 VSS_48 GND 43, 44 DOT96T/ 27M_NSS DOT96C/ 27M_SS 45 FSB/TEST_MODE 47, 48 SRC[T/C]0/ LCD100M[T/C] O,DIF 100-MHz differential serial reference clock output/Differential 96/100-MHz SS clock for flat-panel display Selected via FCTSEL1 at pin 39 assertion. 50, 51 SRCT_1/SATAT, SRCC_1/SATAC O, DIF 100-MHz Differential serial reference clocks. Fixed 48-MHz clock output/3.3V-tolerant input for CPU frequency selection Refer to DC Electrical Specifications table for Vil_FS and Vih_FS specifications. Ground for outputs. O, DIF Fixed 96-MHz clock output or 27 Mhz Spread and Non-spread output Selected via FCTSEL1 at pin 39 assertion. I 3.3V-tolerant input for CPU frequency selection. Selects Ref/N or Tri-state when in test mode 0 = Tri-state, 1 = Ref/N Refer to DC Electrical Specifications table for Vil_FS and Vih_FS specifications. Frequency Select Pins (FSA, FSB, and FSC) Serial Data Interface Host clock frequency selection is achieved by applying the appropriate logic levels to FSA, FSB, FSC inputs prior to CK_PWRGD assertion (as seen by the clock synthesizer). Upon CK_PWRGD being sampled HIGH by the clock chip (indicating processor CK_PWRGD voltage is stable), the clock chip samples the FSA, FSB, and FSC input values. For all logic levels of FSA, FSB, and FSC, CK_PWRGD employs a one-shot functionality in that once a valid HIGH on CK_PWRGD has been sampled, all further CK_PWRGD, FSA, FSB, and FSC transitions will be ignored, except in test mode. To enhance the flexibility and function of the clock synthesizer, a two-signal serial interface is provided. Through the Serial Data Interface, various device functions, such as individual clock output buffers, can be individually enabled or disabled. The registers associated with the Serial Data Interface initialize to their default setting upon power-up, and therefore use of this interface is optional. Clock device register changes are normally made upon system initialization, if any are required. The interface cannot be used during system operation for power management functions. .......................Document #: 001-05103 Rev *B Page 3 of 27 SL28647 Data Protocol system controller can access individually indexed bytes. The offset of the indexed byte is encoded in the command code, as described in Table 3. The clock driver serial protocol accepts byte write, byte read, block write, and block read operations from the controller. For block write/read operation, the bytes must be accessed in sequential order from lowest to highest byte (most significant bit first) with the ability to stop after any complete byte has been transferred. For byte write and byte read operations, the The block write and block read protocol is outlined in Table 4 while Table 5 outlines the corresponding byte write and byte read protocol. The slave receiver address is 11010010 (D2h) Table 2. Frequency Select Table FSA, FSB, and FSC FSC FSB FSA CPU 0 0 0 266 MHz 1 0 1 100 MHz 0 0 1 133 MHz 0 1 1 166 MHz 0 1 0 200 MHz 1 0 0 333 MHz 1 1 0 400 MHz 1 1 1 SRC PCIF/PCI 27MHz REF DOT96 USB 100 MHz 33 MHz 27 MHz 14.318 MHz 96 MHz 48 MHz Reserved Table 3. Command Code Definition Bit 7 (6:0) Description 0 = Block read or block write operation, 1 = Byte read or byte write operation Byte offset for byte read or byte write operation. For block read or block write operations, these bits should be '0000000' Table 4. Block Read and Block Write Protocol Block Write Protocol Bit 1 8:2 9 10 18:11 19 27:20 28 36:29 37 45:38 Description Start Slave address–7 bits Write Acknowledge from slave Command Code–8 bits Block Read Protocol Bit 1 8:2 9 10 18:11 Description Start Slave address–7 bits Write Acknowledge from slave Command Code–8 bits Acknowledge from slave 19 Acknowledge from slave Byte Count–8 bits (Skip this step if I2C_EN bit set) 20 Repeat start Acknowledge from slave 27:21 Slave address–7 bits Data byte 1–8 bits 28 Read = 1 Acknowledge from slave 29 Acknowledge from slave Data byte 2–8 bits 46 Acknowledge from slave .... Data Byte/Slave Acknowledges .... Data Byte N–8 bits .... Acknowledge from slave .... Stop .......................Document #: 001-05103 Rev *B Page 4 of 27 37:30 38 46:39 47 55:48 56 Byte Count from slave–8 bits Acknowledge Data byte 1 from slave–8 bits Acknowledge Data byte 2 from slave–8 bits Acknowledge .... Data bytes from slave/Acknowledge .... Data Byte N from slave–8 bits .... NOT Acknowledge .... Stop SL28647 Table 5. Byte Read and Byte Write Protocol Byte Write Protocol Bit 1 8:2 9 10 18:11 19 27:20 Byte Read Protocol Description Bit Start 1 Slave address–7 bits 8:2 Write 9 Acknowledge from slave 10 Command Code–8 bits 18:11 Description Start Slave address–7 bits Write Acknowledge from slave Command Code–8 bits Acknowledge from slave 19 Acknowledge from slave Data byte–8 bits 20 Repeated start 28 Acknowledge from slave 29 Stop 27:21 28 29 37:30 Slave address–7 bits Read Acknowledge from slave Data from slave–8 bits 38 NOT Acknowledge 39 Stop Control Registers Byte 0 Control Register 0 Bit @Pup Name Description 7 0 RESEREVD RESERVED 6 0 RESEREVD RESERVED 5 0 RESEREVD RESERVED 4 0 iAMT_EN 3 0 RESEREVD RESERVED 2 0 RESEREVD RESERVED 1 0 RESEREVD RESERVED 0 1 PD_Restore Save configuration when PD# is asserted 0 = Config. cleared, 1 = Config. saved Set via SMBus or by combination of PD, CPU_STP and PCI_STP 0 = Legacy mode, 1 = iAMT enable Byte 1 Control Register 1 Bit @Pup Name Description 7 1 SRC7_OE SRC7 Output Enable 0 = Disabled, 1 = Enabled 6 1 SRC6_OE SRC[6 Output Enable 0 = Disabled, 1 = Enabled 5 1 SRC5_OE SRC5 Output Enable 0 = Disabled, 1 = Enabled 4 1 SRC4_OE SRC4 Output Enable 0 = Disabled, 1 = Enabled 3 1 SRC3_OE SRC3 Output Enable 0 = Disabled, 1 = Enabled 2 1 SRC2_OE SRC2 Output Enable 0 = Disabled, 1 = Enabled 1 1 SRC1_OE SRC1 Output Enable 0 = Disabled, 1 = Enabled 0 1 SRC0 /LCD_96/100M_OE SRC0/LCD_96/100M Output Enable 0 = Disabled, 1 = Enabled .......................Document #: 001-05103 Rev *B Page 5 of 27 SL28647 Byte 2 Control Register 2 Bit @Pup Name Description 7 1 PCIF0_OE 6 1 5 1 48M_OE 48-MHz Output Enable 0 = Disabled, 1 = Enabled 4 1 REF0_OE REF0 Output Enable 0 = Disabled, 1 = Enabled 3 1 REF1_OE REF1 Output Enable 0 = Disabled, 1 = Enabled 2 1 CPU1_OE CPU[T/C]1 Output Enable 0 = Disabled, 1 = Enabled 1 1 CPU0_OE CPU[T/C]0 Output Enable 0 = Disabled, 1 = Enabled 0 1 CPU, SRC, PCI, PCIF Spread Enable PCIF0 Output Enable 0 = Disabled, 1 = Enabled 27M_non_SS/DOT_96_OE 27M Non-spread and DOT_96 MHz Output Enable 0 = Disable, 1 = Enabled PLL1 (CPU PLL) Spread Spectrum Enable 0 = Spread off, 1 = Spread on Byte 3 Control Register 3 Bit @Pup Name 7 1 PCI4_OE PCI4 Output Enable 0 = Disabled, 1 = Enabled Description 6 1 PCI3_OE PCI3 Output Enable 0 = Disabled, 1 = Enabled 5 1 PCI2_OE PCI2 Output Enable 0 = Disabled, 1 = Enabled 4 1 PCI1_OE PCI1 Output Enable 0 = Disabled, 1 = Enabled 3 1 RESERVED 2 1 RESERVED 1 1 CPU2/SRC10_OE 0 1 RESERVED RESERVED RESERVED CPU2/SRC10 Output Enable 0 = Disabled, 1 = Enabled RESERVED Byte 4 Control Register 4 Bit @Pup Name Description 7 0 SRC7_STP_CTRL Allow control of SRC7 with assertion of PCI_STP# or SW PCI_STP 0 = Free running, 1 = Stopped with PCI_STP# 6 0 SRC6_STP_CTRL Allow control of SRC6 with assertion of PCI_STP# or SW PCI_STP 0 = Free running, 1 = Stopped with PCI_STP# 5 0 SRC5_STP_CTRL Allow control of SRC5 with assertion of PCI_STP# or SW PCI_STP 0 = Free running, 1 = Stopped with PCI_STP# 4 0 SRC4_STP_CTRL Allow control of SRC4 with assertion of PCI_STP# or SW PCI_STP 0 = Free running, 1 = Stopped with PCI_STP# 3 0 SRC3_STP_CTRL Allow control of SRC3 with assertion of PCI_STP# or SW PCI_STP 0 = Free running, 1 = Stopped with PCI_STP# 2 0 SRC2_STP_CTRL Allow control of SRC2 with assertion of PCI_STP# or SW PCI_STP 0 = Free running, 1 = Stopped with PCI_STP# 1 0 SRC1_STP_CTRL Allow control of SRC1 with assertion of PCI_STP# or SW PCI_STP 0 = Free running, 1 = Stopped with PCI_STP# .......................Document #: 001-05103 Rev *B Page 6 of 27 SL28647 Byte 4 Control Register 4 (continued) Bit @Pup Name 0 0 SRC0_STP_CTRL Description Allow control of SRC0 with assertion of PCI_STP# or SW PCI_STP 0 = Free running, 1 = Stopped with PCI_STP# Byte 5 Control Register 5 Bit @Pup 7 0 Name Description 6 0 DOT96_PD_Drive_Mode 5 0 RESERVED RESERVED RESERVED LCD_96/100M_PD_Drive_Mode LCD_96/100 PWRDWN Drive Mode 0 = Driven in PWRDWN, 1 = Tri-state DOT96 PWRDWN Drive Mode 0 = Driven in PWRDWN, 1 = Tri-state 4 0 RESERVED 3 0 PCIF0_STP_CTRL Allow control of PCIF0 with assertion of SW and HW PCI_STP# 0 = Free running, 1 = Stopped with PCI_STP# 2 1 CPU2_STP_CTRL Allow control of CPU[T/C]2 with assertion of CPU_STP# 0 = Free running, 1 = Stopped with CPU_STP# 1 1 CPU1_STP_CTRL Allow control of CPU[T/C]1 with assertion of CPU_STP# 0 = Free running, 1 = Stopped with CPU_STP# 0 1 CPU0_STP_CTRL Allow control of CPU[T/C]0 with assertion of CPU_STP# 0 = Free running, 1 = Stopped with CPU_STP# Byte 6 Control Register 6 Bit @Pup Name Description 7 0 SRC_STP_Drive_Mode SRC Stop Drive Mode 0 = Driven when PCI_STP# asserted 1 = Tri-state when PCI_STP# asserted 6 0 CPU2_STP_Drive_Mode CPU2 Stop Drive Mode 0 = Driven when CPU_STP# asserted 1 = Tri-state when CPU_STP# asserted 5 0 CPU1_STP_Drive_Mode CPU1 Stop Drive Mode 0 = Driven when CPU_STP# asserted 1 = Tri-state when CPU_STP# asserted 4 0 CPU0_STP_Drive_Mode CPU0 Stop Drive Mode 0 = Driven when CPU_STP# asserted 1 = Tri-state when CPU_STP# asserted 3 0 2 0 CPU2_PD_Drive_Mode CPU2 PWRDWN Drive Mode 0 = Driven when PD asserted 1 = Tri-state when PD asserted 1 0 CPU1_PD_Drive_Mode CPU1 PWRDWN Drive Mode 0 = Driven when PD asserted 1 = Tri-state when PD asserted 0 0 CPU0_PD_Drive_Mode CPU0 PWRDWN Drive Mode 0 = Driven when PD asserted 1 = Tri-state when PD asserted SRC_[9:1]_PD_Drive_Mode SRC[9:1] PWRDWN Drive Mode 0 = Driven when PD asserted 1 = Tri-state when PD asserted Byte 7 Control Register 7 Bit @Pup Name 7 0 TEST_SEL Description REF/N or Tri-state Select 0 = Tri-state, 1 = REF/N Clock .......................Document #: 001-05103 Rev *B Page 7 of 27 SL28647 Byte 7 Control Register 7 (continued) Bit @Pup Name Description 6 0 TEST_MODE 5 1 REF1 Bit0 REF1 Slew Rate Control Bit 0, See Table 6 for more detail 0 = Low, 1 = High 4 1 REF0 Bit0 REF0 Slew Rate Control Bit 0, See Table 6 for more detail 0 = Low, 1 = High 3 1 2 HW FSC FSC Reflects the value of the FSC pin sampled on power up 0 = FSC was low during CK_PWRGD assertion 1 HW FSB FSB Reflects the value of the FSB pin sampled on power up 0 = FSB was low during CK_PWRGD assertion 0 HW FSA FSA Reflects the value of the FSA pin sampled on power up 0 = FSA was low during CK_PWRGD assertion Test Clock Mode Entry Control 0 = Normal operation, 1 = REF/N or Tri-state mode, PCI, PCIF and SRC clock SW PCI_STP Function outputs except those set to 0 = SW PCI_STP assert, 1= SW PCI_STP deassert free running When this bit is set to 0, all STOPPABLE PCI, PCIF and SRC outputs will be stopped in a synchronous manner with no short pulses. When this bit is set to 1, all STOPPED PCI, PCIF and SRC outputs will resume in a synchronous manner with no short pulses. Byte 8 Vendor ID Bit @Pup Name 7 0 Revision Code Bit 3 Revision Code Bit 3 Description 6 0 Revision Code Bit 2 Revision Code Bit 2 5 1 Revision Code Bit 1 Revision Code Bit 1 4 0 Revision Code Bit 0 Revision Code Bit 0 3 1 Vendor ID Bit 3 Vendor ID Bit 3 2 0 Vendor ID Bit 2 Vendor ID Bit 2 1 0 Vendor ID Bit 1 Vendor ID Bit 1 0 0 Vendor ID Bit 0 Vendor ID Bit 0 Byte 9 Control Register 9 Bit @Pup Name Description 7 0 RESERVED RESERVED 6 0 RESERVED RESERVED 5 0 RESERVED RESERVED 4 0 RESERVED RESERVED 3 1 RESERVED RESERVED 2 1 48M Bit0 1 1 RESERVED 0 1 PCIF0 Bit0 48M Slew Rate Control Bit 0, See Table 6 for more detail 0 = Low, 1 = High RESERVED PCIF0 Slew Rate Control Bit 0, See Table 6 for more detail 0 = Low, 1 = High Byte 10 Control Register 10 Bit @Pup Name 7 0 RESERVED RESERVED Description 6 0 RESERVED RESERVED .......................Document #: 001-05103 Rev *B Page 8 of 27 SL28647 Byte 10 Control Register 10 (continued) Bit @Pup Name Description 5 0 S1 4 0 S0 3 1 RESERVED RESERVED 2 1 27M_SS_OE 27M_SS Output Enable 0 =Disabled, 1 = Enabled 1 1 0 0 27M_SS/LCD 96_100M SS Spread Spectrum Selection table: S[1:0] SS% ‘00’ = –0.5%(Default value) ‘01’ = –1.0% ‘10’ = –1.5% ‘11’ = –2.0% 27M_SS/LCD_96M/100M 27M_SS/LCD_96/100M Spread spectrum enable. Spread Enable 0 = Spread Disabled, 1 = Spread Enabled RESERVED RESERVED Byte 11 Control Register 11 Bit @Pup Name 7 1 RESERVED RESERVED Description 6 1 RESERVED RESERVED 5 1 SRC9_OE SRC9 Output Enable 0 = Disabled, 1 = Enabled 4 1 SRC8_OE SRC8 Output Enable 0 = Disabled, 1 = Enabled 3 0 RESERVED 2 0 SRC10_STP_CTRL Allow control of SRC10 with assertion of SW PCI_STP# 0 = Free running, 1 = Stopped with PCI_STP# 1 0 SRC9_STP_CTRL Allow control of SRC9 with assertion of SW PCI_STP# 0 = Free running, 1 = Stopped with PCI_STP# 0 0 SRC8_STP_CTRL Allow control of SRC8 with assertion of SW PCI_STP# 0 = Free running, 1 = Stopped with PCI_STP# RESERVED Byte 12 Control Register 12 Bit @Pup Name Description 7 0 DIAG_EN 6 HW CPU PLL Status CPU_PLL status 0 = PLL not locked; 1 = PLL locked 5 HW Video PLL Status Video_PLL status 0 = PLL not locked; 1 = PLL locked 4 HW Fixed PLL Status Fixed_PLL status 0 = PLL not locked; 1 = PLL locked 3 HW PCIe PLL Status PCIe_PLL status 0 = PLL not locked; 1 = PLL locked 2 HW Frequency Accuracy 1 1 Byte 0 Access Diagnostic Bits Enabled 0 = Reset (default) setting bit 6, 5, 4, 2, 0 to zero 1 = DIAG mode enabled Primiary PLL or external crystal Frequency Accuracy 0=Frequency not accurate, 1=Frequency Accurate Byte 0 Access Control 0 = Disabled, 1 = Enabled .......................Document #: 001-05103 Rev *B Page 9 of 27 SL28647 Byte 12 Control Register 12 Bit @Pup Name 0 HW PWRGOOD Description Power on reset status bit 0 = All of the below conditions are not meet 1 = Valid voltage levels exist on VDD_SRC/CPU, VDD_REF, VDDA, VDD_48, VDD_PCI and CKPWRGD is asserted and external crystal is detected. Byte 13 Control Register 13 Bit @Pup Name Description 7 0 CLKREQ#9 CLKREQ#9 Input Enable 0 = Disabled, 1 = Enabled 6 0 CLKREQ#8 CLKREQ#8 Input Enable 0 = Disabled, 1 = Enabled 5 0 CLKREQ#7 CLKREQ#7 Input Enable 0 = Disabled, 1 = Enabled 4 0 CLKREQ#6 CLKREQ#6 Input Enable 0 = Disabled, 1 = Enabled 3 0 CLKREQ#5 CLKREQ#5 Input Enable 0 = Disabled, 1 = Enabled 2 0 CLKREQ#4 CLKREQ#4 Input Enable 0 = Disabled, 1 = Enabled 1 0 CLKREQ#3 CLKREQ#3 Input Enable 0 = Disabled, 1 = Enabled 0 0 CLKREQ#2 CLKREQ#2 Input Enable 0 = Disabled, 1 = Enabled Byte 14 Control Register 14 Bit @Pup Name Description 7 0 CLKREQ#1 6 1 LCD _96/100M Clock Speed 5 1 27M_SS Bit 0 4 1 27M_non-SS Bit 0 3 1 PCI4 Bit 0 PCI4 Slew Rate Control Bit 0, See Table 6 for more detail 0 = Low, 1 = High 2 1 PCI3 Bit 0 PCI3 Slew Rate Control Bit 0, See Table 6 for more detail 0 = Low, 1 = High 1 1 PCI2 Bit 0 PCI2 Slew Rate Control Bit 0, See Table 6 for more detail 0 = Low, 1 = High 0 1 PCI1 Bit 0 PCI1Slew Rate Control Bit 0, See Table 6 for more detail 0 = Low, 1 = Highh CLKREQ#1 Input Enable 0 = Disabled, 1 = Enabled LCD 96_100M Clock Speed 0 = 96 MHz, 1 = 100 MHz 27M SS Slew Rate Control Bit 0, See Table 6 for more detail 0 = Low, 1 = High 27M non-SS Slew Rate Control Bit 0, See Table 6 for more detail 0 = Low, 1 = High Byte 15 Control Register 15 Bit @Pup Name Description 7 HW TME_STRAP Trusted mode enable strap status, 0 = Normal 1 = No overclocking (default) 6 1 RESERVED RESERVED 5 1 RESERVED RESERVED .....................Document #: 001-05103 Rev *B Page 10 of 27 SL28647 Byte 15 Control Register 15 Bit @Pup Name 4 1 RESERVED RESERVED 3 1 RESERVED RESERVED IO_VOUT[2,1,0] 000 = 0.30V 001 = 0.40V 010 = 0.50V 011 = 0.60V 100 = 0.70V 101 = 0.80V (Default) 110 = 0.90V 111 = 1.00V 2 1 IO_VOUT2 1 0 IO_VOUT1 0 1 IO_VOUT0 Description Byte 16 Control Register 16 Bit @Pup Name 7 1 PCI4 Bit 1 PCI4 Slew Rate Control Bit 1, See Table 6 for more detail 0=Low, 1 = High Description 6 1 PCI3 Bit 1 PCI3 Slew Rate Control Bit 1, See Table 6 for more detail 0=Low, 1 = High 5 1 PCI2 Bit 1 PCI2 Slew Rate Control Bit 1, See Table 6 for more detail 0=Low, 1 = High 4 1 PCI1 Bit 1 PCI1 Slew Rate Control Bit 1, See Table 6 for more detail 0=Low, 1 = High 3 1 PCIF0 Bit 1 2 1 48M Bit 1 1 1 27M_SS Bit 1 0 1 27M_non-SS Bit 1 PCIF0 Slew Rate Control Bit 1, See Table 6 for more detail 0=Low, 1 = High 48M Slew Rate Control Bit 1, See Table 6 for more detail 0=Low, 1 = High 27M_SS Slew Rate Control Bit 1, See Table 6 for more detail 0=Low, 1 = High 27M_non-SS Slew Rate Control Bit 1, See Table 6 for more detail 0=Low, 1 = High Byte 17 Control Register 17 Bit @Pup Name 7 1 27M_SS Bit 2 Description 6 1 27M_non_SS Bit 2 5 1 REF1 Bit 1 REF1 Slew Rate Control Bit 1, See Table 6 for more detail 0=Low, 1 = High 4 1 REF0 Bit 1 REF0 Slew Rate Control Bit 1, See Table 6 for more detail 0=Low, 1 = High 3 1 REF1 Bit 2 REF1 Slew Rate Control Bit 2, See Table 6 for more detail 0=Low, 1 = High 2 1 REF0 Bit 2 REF0 Slew Rate Control Bit 2, See Table 6 for more detail 0=Low, 1 = High 1 0 RESERVED RESERVED 0 0 RESERVED RESERVED 27MHz_SS Slew Rate Control Bit 2, See Table 6 for more detail 0=Low, 1 = High 27MHz_non_SS Slew Rate Control Bit 2, See Table 6 for more detail 0=Low, 1 = High ..................... Document #: 001-05103 Rev *B Page 11 of 27 SL28647 Byte 18 Control Register 18 Bit @Pup Name Description 7 1 RESERVED RESERVED 6 1 RESERVED RESERVED 5 1 RESERVED RESERVED 4 1 RESERVED RESERVED 3 1 RESERVED RESERVED 2 1 RESERVED RESERVED 1 1 RESERVED RESERVED 0 1 RESERVED RESERVED Byte 19 Control Register 19 Bit @Pup Name 7 1 PCI4 Bit 2 PCI4 Slew Rate Control Bit 2, See Table 6 for more detail 0=Low, 1 = High Description 6 1 PCI3 Bit 2 PCI3 Slew Rate Control Bit 2, See Table 6 for more detail 0=Low, 1 = High 5 1 PCI2 Bit 2 PCI2 Slew Rate Control Bit 2, See Table 6 for more detail 0=Low, 1 = High 4 1 PCI1 Bit 2 PCI1 Slew Rate Control Bit 2, See Table 6 for more detail 0=Low, 1 = High 3 1 PCIF0 Bit 2 2 1 48M Bit 2 1 1 RESERVED RESERVED 0 1 RESERVED RESERVED PCIF0 Slew Rate Control Bit 2, See Table 6 for more detail 0=Low, 1 = High 48M Slew Rate Control Bit 2, See Table 6 for more detail 0=Low, 1 = High Table 6. Slew Rate Control Table Default Slew Rate Control Bit [2:0] Bit2 Bit1 Bit0 1 1 1 1 1 0 1 0 1 1 0 0 0 1 1 0 1 0 0 0 1 0 0 0 Slew Rate Fastest Slowest Table 7. Crystal Recommendation Frequency (Fund) Cut Loading Load Cap Drive (max.) Shunt Cap (max.) Motional (max.) Tolerance (max.) Stability (max.) Aging (max.) 14.31818 MHz AT Parallel 0.1 mW 5 pF 0.016 pF 35 ppm 30 ppm 5 ppm 20 pF The SL28647 requires a Parallel Resonance Crystal. Substituting a series resonance crystal will cause the SL28647 to .....................Document #: 001-05103 Rev *B Page 12 of 27 operate at the wrong frequency and violate the ppm specification. For most applications there is a 300-ppm frequency SL28647 shift between series and parallel crystals due to incorrect loading. Use the following formulas to calculate the trim capacitor values for Ce1 and Ce2. Load Capacitance (each side) Crystal Loading Crystal loading plays a critical role in achieving low ppm performance. To realize low ppm performance, the total capacitance the crystal will see must be considered to calculate the appropriate capacitive loading (CL). Figure 1 shows a typical crystal configuration using the two trim capacitors. An important clarification for the following discussion is that the trim capacitors are in series with the crystal not parallel. It’s a common misconception that load capacitors are in parallel with the crystal and should be approximately equal to the load capacitance of the crystal. This is not true. Ce = 2 * CL – (Cs + Ci) Total Capacitance (as seen by the crystal) CLe = 1 1 ( Ce1 + Cs1 + Ci1 + 1 Ce2 + Cs2 + Ci2 ) CL....................................................Crystal load capacitance CLe......................................... Actual loading seen by crystal using standard value trim capacitors Ce..................................................... External trim capacitors Cs .............................................. Stray capacitance (terraced) Ci ...........................................................Internal capacitance (lead frame, bond wires etc.) CLK_REQ# Description Figure 1. Crystal Capacitive Clarification Calculating Load Capacitors In addition to the standard external trim capacitors, trace capacitance and pin capacitance must also be considered to correctly calculate crystal loading. As mentioned previously, the capacitance on each side of the crystal is in series with the crystal. This means the total capacitance on each side of the crystal must be twice the specified crystal load capacitance (CL). While the capacitance on each side of the crystal is in series with the crystal, trim capacitors (Ce1,Ce2) should be calculated to provide equal capacitive loading on both sides. Figure 2. Crystal Loading Example .....................Document #: 001-05103 Rev *B Page 13 of 27 The CLKREQ# signals are active LOW inputs used for clean enabling and disabling selected SRC outputs. The outputs controlled by CLKREQ# are determined by the settings in register byte 8. The CLKREQ# signal is a de-bounced signal in that it’s state must remain unchanged during two consecutive rising edges of SRCC to be recognized as a valid assertion or deassertion. (The assertion and deassertion of this signal is absolutely asynchronous.) CLK_REQ[1:9]# Assertion (CLKREQ# -> LOW) All differential outputs that were stopped are to resume normal operation in a glitch-free manner. The maximum latency from the assertion to active outputs is between 2 and 6 SRC clock periods (2 clocks are shown) with all SRC outputs resuming simultaneously. All stopped SRC outputs must be driven HIGH within 10 ns of CLKREQ# deassertion to a voltage greater than 200 mV. SL28647 Figure 3. CLK_REQ#[1:9] Deassertion/Assertion Waveform CLK_REQ[1:9]# Deassertion (CLKREQ# -> HIGH) The impact of deasserting the CLKREQ# pins is that all SRC outputs that are set in the control registers to stoppable via deassertion of CLKREQ# are to be stopped after their next transition. The final state of all stopped SRC clocks is Low/Low. PD (Power-down) Clarification The CK_PWRGD/PD# pin is a dual-function pin. During initial power-up, the pin functions as CK_PWRGD. Once CK_PWRGD has been sampled HIGH by the clock chip, the pin assumes PD# functionality. The PD# pin is an asynchronous active LOW input used to shut off all clocks cleanly prior to shutting off power to the device. This signal is synchronized internal to the device prior to powering down the clock synthesizer. PD# is also an asynchronous input for powering up the system. When PD# is asserted LOW, all clocks need to be driven to a LOW value and held prior to turning off the VCOs and the crystal oscillator. PD (Power-down) Assertion When PD# is sampled LOW by two consecutive rising edges of CPUC, all single-ended outputs will be held LOW on their next HIGH-to-LOW transition and differential clocks must be held HIGH or tri-stated (depending on the state of the control register drive mode bit) on the next diff clock# HIGH-to-LOW transition within 4 clock periods. When the SMBus PD drive mode bit corresponding to the differential (CPU, SRC, and DOT) clock output of interest is programmed to ‘0’, the clock outputs are held with “Diff clock” pin driven HIGH, and “Diff clock#” tri-state. If the control register PD drive mode bit corresponding to the output of interest is programmed to “1”, then both the “Diff clock” and the “Diff clock#” are tri-state. Note that Figure 4 shows CPUT = 133 MHz and PD drive mode = ‘1’ for all differential outputs. This diagram and description is applicable to valid CPU frequencies 100, 133, 166, and 200 MHz. In the event that PD mode is desired as the initial power-on state, PD must be asserted HIGH in less than 10 s after asserting CK_PWRGD. It should be noted that 96_100_SSC will follow the DOT waveform when selected for 96 MHz and the SRC waveform when in 100-MHz mode. PD Deassertion The power-up latency is less than 1.8 ms. This is the time from the deassertion of the PD pin or the ramping of the power supply until the time that stable clocks are output from the clock chip. All differential outputs stopped in a three-state condition resulting from power down will be driven high in less than 300 s of PD deassertion to a voltage greater than 200 mV. After the clock chip’s internal PLL is powered up and locked, all outputs will be enabled within a few clock cycles of each other. Figure 5 is an example showing the relationship of clocks coming up. It should be noted that 96_100_SSC will follow the DOT waveform when selected for 96 MHz and the SRC waveform when in 100-MHz mode. PD# CPUT, 133MHz CPUC, 133MHz SRCT 100MHz SRCC 100MHz USB, 48MHz DOT96T DOT96C PCI, 33 MHz REF Figure 4. Power-down Assertion Timing Waveform .....................Document #: 001-05103 Rev *B Page 14 of 27 SL28647 Tstable 200 mV Figure 7. CPU_STP# Deassertion Waveform .....................Document #: 001-05103 Rev *B Page 15 of 27 SL28647 PCI_STP# Assertion The PCI_STP# signal is an active LOW input used for synchronous stopping and starting the PCI outputs and SRC outputs if they are set to be stoppable in SMbus while the rest of the clock generator continues to function. The set-up time for capturing PCI_STP# going LOW is 10 ns (tSU). (See Figure 9.) The PCIF clocks will not be affected by this pin if their corresponding control bit in the SMBus register is set to allow them to be free running. All stopped PCI outputs are driven Low, SRC outputs are High/Low if set to driven and Low/Low if set to tri-state. PCI_STP# Deassertion The deassertion of the PCI_STP# signal will cause all PCI and stoppable PCIF clocks to resume running in a synchronous manner within two PCI clock periods after PCI_STP# transitions to a HIGH level. 1.8mS CPU_STOP# PD CPUT(Free Running) CPUC(Free Running) CPUT(Stoppable) CPUC(Stoppable) DOT96T DOT96C Figure 8. CPU_STP# = Tri-state, CPU_PD = Tri-state, DOT_PD = Tri-state Tsu PCI_STP# PCI_F PCI SRC 100MHz Figure 9. PCI_STP# Assertion Waveform 1.8 ms CPU_STOP# PD CPUT(Free Running CPUC(Free Running CPUT(Stoppable) CPUC(Stoppable) Figure 10. CPU_STP# = Driven, CPU_PD = Driven, DOT_PD = Driven .....................Document #: 001-05103 Rev *B Page 16 of 27 SL28647 Tdrive_SRC Tsu PCI_STP# PCI_F PCI SRC 100MHz Figure 11. PCI_STP# Deassertion Waveform Figure 12. CK_PWRGD Timing DIagram Table 8. Default Condition for Output Driver Status PCI_STOP# Asserted Single-ended Clocks Stoppable Differential Clocks CPU_STOP# Asserted Driven Low Running Non Stoppable Running Running Stoppable Clock Drive High Clock# Driven Low Clock Drive High Clock# Driven Low Non Stoppable Running Running SMBus OE Disabled Driven Low Driven Low or 20K pulldown Table 9. Default Condition for Output Driver Status All Single-ended Clocks All Differential Clocks except CPU1 w/o Strap w/Strap Clock Latches Open State Low Hi-Z Low or 20K pulldown Low Powerdown (PD#) Low Hi-Z Low or 20K pulldown Low Low or 20K pulldown Low M1 Low Hi-Z Low or 20K pulldown Low Running .....................Document #: 001-05103 Rev *B Page 17 of 27 Clock# CPU1 Clock Clock# Low or 20K pulldown Low Running SL28647 Figure 13. SL28647 State Diagram C l o c k O f f t o M1 3.3V Vcc 2.0V FSC T_delay t CPU_STOP# FSB FSA PCI_STOP# CKPWRGD/PWRDWN Off CK505 SMBUS CK505 State Latches Open Off M1 BSEL[0..2] CK505 Core Logic Off PLL1 Locked CPU1 PLL2 & PLL3 All Other Clocks REF Oscillator T_delay2 T_delay3 Figure 14. BSEL Serial Latching .....................Document #: 001-05103 Rev *B Page 18 of 27 SL28647 Absolute Maximum Conditions Min. Max. Unit VDD Parameter Core Supply Voltage Description – 4.6 V VDD_A Analog Supply Voltage – 4.6 V VIN Input Voltage Relative to VSS –0.5 TS Temperature, Storage Non-functional –65 150 °C TA Temperature, Operating Ambient Functional 0 70 °C TJ Temperature, Junction Functional – 150 °C ØJC Dissipation, Junction to Case Mil-STD-883E Method 1012.1 – 20 °C/W ØJA Dissipation, Junction to Ambient JEDEC (JESD 51) – 60 °C/W ESDHBM ESD Protection (Human Body Model) MIL-STD-883, Method 3015 2000 – V UL-94 Flammability Rating MSL Moisture Sensitivity Level Condition At 1/8 in. VDD + 0.5 VDC V–0 2 Multiple Supplies: The Voltage on any input or I/O pin cannot exceed the power pin during power-up. Power supply sequencing is NOT required. DC Electrical Specifications Parameter Description Condition All VDDs 3.3V Operating Voltage 3.3 ± 5% VILI2C Input Low Voltage SDATA, SCLK VIHI2C Input High Voltage SDATA, SCLK VIL_FS FS_[A,B] Input Low Voltage Min. Max. Unit 3.135 3.465 V – 1.0 V 2.2 – V VSS – 0.3 0.35 V 0.7 VDD + 0.5 V VSS – 0.3 0.35 V VIH_FS FS_[A,B] Input High Voltage VILFS_C FS_C Input Low Voltage VIMFS_C FS_C Input Middle Voltage 0.7 1.7 V VIHFS_C FS_C Input High Voltage 2.0 VDD + 0.5 V VIL 3.3V Input Low Voltage VSS – 0.3 0.8 V VIH 3.3V Input High Voltage 2.0 VDD + 0.3 V IIL Input Low Leakage Current Except internal pull-up resistors, 0 < VIN < VDD –5 5 A IIH Input High Leakage Current Except internal pull-down resistors, 0 < VIN < VDD – 5 A VOL 3.3V Output Low Voltage IOL = 1 mA VOH 3.3V Output High Voltage IOH = –1 mA – 0.4 V 2.4 – V IOZ High-impedance Output Current –10 10 A CIN Input Pin Capacitance 3 5 pF COUT Output Pin Capacitance 3 6 pF LIN Pin Inductance – 7 nH VXIH Xin High Voltage 0.7VDD VDD V VXIL Xin Low Voltage 0 0.3VDD V IDD3.3V Dynamic Supply Current – 250 mA IPD3.3V Power-down Supply Current PD asserted, Outputs Driven – 30 mA IPD3.3V Power-down Supply Current PD asserted, Outputs Tri-state – 5 mA Min. Max. Unit AC Electrical Specifications Parameter Description Crystal .....................Document #: 001-05103 Rev *B Page 19 of 27 Condition SL28647 AC Electrical Specifications (continued) Parameter Description Condition Min. Max. Unit The device will operate reliably with input duty cycles up to 30/70 but the REF clock duty cycle will not be within specification 47.5 52.5 % When XIN is driven from an external clock source 69.841 71.0 ns Measured between 0.3VDD and 0.7VDD – 10.0 ns As an average over 1-s duration – 500 ps CPUT and CPUC Duty Cycle Measured at 0V differential at 0.1s 45 55 % TPERIOD 100 MHz CPUT and CPUC Period Measured at 0V differential at 0.1s 9.99900 10.0010 ns TPERIOD 133 MHz CPUT and CPUC Period Measured at 0V differential at 0.1s 7.49925 7.50075 ns TPERIOD 166 MHz CPUT and CPUC Period Measured at 0V differential at 0.1s 5.99940 6.00060 ns TPERIOD 200 MHz CPUT and CPUC Period Measured at 0V differential at 0.1s 4.99950 5.00050 ns TPERIOD 266 MHz CPUT and CPUC Period Measured at 0V differential at 0.1s 3.74963 3.75038 ns TPERIOD 333 MHz CPUT and CPUC Period Measured at 0V differential at 0.1s 2.99970 3.00030 ns TPERIOD 400 MHz CPUT and CPUC Period Measured at 0V differential at 0.1s 2.49975 2.50025 ns TPERIODSS 100 MHz CPUT and CPUC Period, SSC Measured at 0V differential at 0.1s 10.02406 10.02607 ns TPERIODSS 133 MHz CPUT and CPUC Period, SSC Measured at 0V differential at 0.1s 7.51804 7.51955 ns TPERIODSS 166 MHz CPUT and CPUC Period, SSC Measured at 0V differential at 0.1s 6.01444 6.01564 ns TPERIODSS 200 MHz CPUT and CPUC Period, SSC Measured at 0V differential at 0.1s 5.01203 5.01303 ns TPERIODSS 266 MHz CPUT and CPUC Period, SSC Measured at 0V differential at 0.1s 3.75902 3.75978 ns TPERIODSS 333 MHz CPUT and CPUC Period, SSC Measured at 0V differential at 0.1s 3.00722 3.00782 ns TPERIODSS 400 MHz CPUT and CPUC Period, SSC Measured at 0V differential at 0.1s 2.50601 2.50652 ns TPERIODAbs 100 MHz CPUT and CPUC Absolute Measured at 0V differential at 1 clock period 9.91400 10.0860 ns TPERIODAbs 133 MHz CPUT and CPUC Absolute Measured at 0V differential at 1 clock period 7.41425 7.58575 ns TPERIODAbs 166 MHz CPUT and CPUC Absolute Measured at 0V differential @ 1 clock period 5.91440 6.08560 ns TPERIODAbs 200 MHz CPUT and CPUC Absolute Measured at 0V differential @ 1 clock period 4.91450 5.08550 ns TPERIODAbs 266 MHz CPUT and CPUC Absolute Measured at 0V differential @ 1 clock period 3.66463 3.83538 ns TPERIODAbs 333 MHz CPUT and CPUC Absolute Measured at 0V differential @ 1 clock period 2.91470 3.08530 ns TPERIODAbs 400 MHz CPUT and CPUC Absolute Measured at 0V differential @ 1 clock period 2.41475 2.58525 ns 100 MHz CPUT and CPUC Absolute Measured at 0V differential @ 1 clock period, SSC 9.91406 10.1362 ns 133 MHz CPUT and CPUC Absolute Measured at 0V differential @ 1 clock period, SSC 7.41430 7.62340 ns 166 MHz CPUT and CPUC Absolute Measured at 0V differential @ 1 clock period, SSC 5.91444 6.11572 ns TDC XIN Duty Cycle TPERIOD XIN Period TR/TF XIN Rise and Fall Times TCCJ XIN Cycle to Cycle Jitter TDC CPU TPERIODSSAbs TPERIODSSAbs TPERIODSSAbs .....................Document #: 001-05103 Rev *B Page 20 of 27 SL28647 AC Electrical Specifications (continued) Parameter Min. Max. Unit 200 MHz CPUT and CPUC Absolute Measured at 0V differential @ 1 clock period, SSC 4.91453 5.11060 ns 266 MHz CPUT and CPUC Absolute Measured at 0V differential @ 1 clock period, SSC 3.66465 3.85420 ns 333 MHz CPUT and CPUC Absolute Measured at 0V differential @ 1 clock period, SSC 2.91472 3.10036 ns 400 MHz CPUT and CPUC Absolute Measured at 0V differential @ 1 clock period, SSC 2.41477 2.59780 ns ODSSAbs TCCJ CPU Cycle to Cycle Jitter – 85 ps TCCJ2 CPU2_ITP Cycle to Cycle Jitter Measured at 0V differential – 125 ps LACC Long-term Accuracy Measured at 0V differential – 100 ppm TSKEW CPU0 to CPU1 Clock Skew Measured at 0V differential – 100 ps TSKEW2 CPU2_ITP to CPU0 Clock Skew Measured at 0V differential – 150 ps TPERIODSSAbs TPERIODSSAbs TPERIODSSAbs TPERI- Description Condition Measured at 0V differential TR / TF CPU Rising/Falling Slew rate Measured differentially from ±150 mV 2.5 8 V/ns TRFM Rise/Fall Matching Measured single-endedly from ±75 mV – 20 % VHIGH Voltage High 1.15 V VLOW Voltage Low –0.3 – V VOX Crossing Point Voltage at 0.7V Swing 300 550 mV SRC at 0.7V TDC SRC Duty Cycle Measured at 0V differential 45 55 % TPERIOD 100 MHz SRC Period Measured at 0V differential @ 0.1s 9.99900 10.0010 ns TPERIODSS 100 MHz SRC Period, SSC Measured at 0V differential @ 0.1s 10.02406 10.02607 ns Measured at 0V differential @ 1 clock 9.87400 10.1260 ns 100 MHz SRC Absolute Period, SSC Measured at 0V differential @ 1 clock 9.87406 10.1762 ns TPERIODAbs 100 MHz SRC Absolute Period TPERIODSSAbs TSKEW(windo Any SRC Clock Skew from the earliest bank to the latest bank w) Measured at 0V differential – 3.0 ns TCCJ SRC Cycle to Cycle Jitter Measured at 0V differential – 125 ps LACC SRC Long Term Accuracy Measured at 0V differential – 100 ppm T R / TF SRC Rising/Falling Slew Rate Measured differentially from ±150 mV 2.5 8 V/ns TRFM Rise/Fall Matching Measured single-endedly from ±75 mV – 20 % VHIGH Voltage High 1.15 V VLOW Voltage Low –0.3 – V VOX Crossing Point Voltage at 0.7V Swing 300 550 mV DOT96 at 0.7V TDC DOT96 Duty Cycle Measured at 0V differential TPERIOD DOT96 Period 45 55 % 10.4177 ns 10.6677 ns Measured at 0V differential at 0.1s 10.4156 TPERIODAbs DOT96 Absolute Period Measured at 0V differential at 0.1s 10.1656 TCCJ DOT96 Cycle to Cycle Jitter Measured at 0V differential at 1 clock – 250 ps LACC DOT96 Long Term Accuracy Measured at 0V differential at 1 clock – 100 ppm TR / TF DOT96 Rising/Falling Slew Rate Measured differentially from ±150 mV 2.5 8 V/ns TRFM Rise/Fall Matching Measured single-endedly from ±75 mV – 20 % VHIGH Voltage High 1.15 V VLOW Voltage Low –0.3 – V VOX Crossing Point Voltage at 0.7V Swing 300 550 mV .....................Document #: 001-05103 Rev *B Page 21 of 27 SL28647 AC Electrical Specifications (continued) Parameter Description Condition Min. Max. 45 55 Unit LCD_100_SSC at 0.7V TDC LCD_100 Duty Cycle Measured at 0V differential TPERIOD 100 MHz LCD_100 Period Measured at 0V differential at 0.1s 9.99900 10.0010 ns TPERIODSS 100 MHz LCD_100 Period, SSC -0.5% Measured at 0V differential at 0.1s 10.0240 10.0260 6 7 ns TPERIODAbs 100 MHz LCD_100 Absolute Period Measured at 0V differential at 1 clock 9.74900 10.2510 0 ns 100 MHz LCD_100 Absolute Period, Measured at 0V differential @ 1 clock SSC 9.74906 10.3012 ns ODSSAbs TPERI- % TCCJ LCD_100 Cycle to Cycle Jitter Measured at 0V differential – 250 ps LACC LCD_100 Long Term Accuracy Measured at 0V differential – 100 ppm T R / TF LCD_100 Rising/Falling Slew Rate Measured differentially from ±150 mV 2.5 8 V/ns TRFM Rise/Fall Matching Measured single-endedly from ±75 mV – 20 % VHIGH Voltage High 1.15 V VLOW Voltage Low –0.3 – V VOX Crossing Point Voltage at 0.7V Swing 300 550 mV 45 55 PCI/PCIF at 3.3V TDC PCI Duty Cycle Measurement at 1.5V TPERIOD Spread Disabled PCIF/PCI Period Measurement at 1.5V 29.99700 30.00300 ns TPERIODSS Spread Enabled PCIF/PCI Period Measurement at 1.5V 30.08421 30.23459 ns TPERIODAbs Spread Disabled PCIF/PCI Period Measurement at 1.5V 29.49700 30.50300 ns TPERI- Spread Enabled PCIF/PCI Period Measurement at 1.5V 29.56617 30.58421 ns THIGH Spread Enabled PCIF and PCI high time Measurement at 2V 12.2709 16.2799 5 5 ns TLOW Spread Enabled PCIF and PCI low time Measurement at 0.8V 11.8709 16.0799 5 5 ns THIGH Spread Disabled PCIF and PCI high Measurement at 2.V time 12.2736 16.2766 5 5 ns TLOW Spread Disabled PCIF and PCI low time Measurement at 0.8V 11.8736 16.0766 5 5 ns T R / TF PCIF/PCI Rising/Falling Slew Rate Measured between 0.8V and 2.0V TSKEW Any PCI clock to Any PCI clock Skew Measurement at 1.5V TCCJ PCIF and PCI Cycle to Cycle Jitter Measurement at 1.5V – 500 ps LACC PCIF/PCI Long Term Accuracy Measurement at 1.5V – 100 ppm TDC Duty Cycle Measurement at 1.5V 45 55 % TPERIOD Period % ODSSAbs 1.0 4.0 V/ns – 1000 ps 48_M at 3.3V Measurement at 1.5V 20.83125 20.83542 TPERIODAbs Absolute Period Measurement at 1.5V 20.48125 21.18542 ns ns THIGH 48_M High time Measurement at 2V 8.216563 11.15198 ns TLOW 48_M Low time Measurement at 0.8V 7.816563 10.95198 ns T R / TF Rising and Falling Edge Rate Measured between 0.8V and 2.0V 1.0 2.0 V/ns TCCJ Cycle to Cycle Jitter Measurement at 1.5V – 350 ps LACC 48M Long Term Accuracy Measurement at 1.5V – 100 ppm Measurement at 1.5V 45 55 % 27M_NSS/27M_SS at 3.3V TDC Duty Cycle .....................Document #: 001-05103 Rev *B Page 22 of 27 SL28647 AC Electrical Specifications (continued) Parameter TPERIOD Description Condition Min. Max. Unit Spread Disabled 27M Period Measurement at 1.5V 37.0359 37.0381 4 3 ns Spread Enabled 27M Period Measurement at 1.5V 37.0129 37.1317 86 2 ns TR / TF Rising and Falling Edge Rate Measured between 0.8V and 2.0V 1.0 4.0 V/ns TCCJ Cycle to Cycle Jitter Measurement at 1.5V – 200 ps LACC 27_M Long Term Accuracy Measured at crossing point VOX – 50 ppm 45 55 REF TDC REF Duty Cycle Measurement at 1.5V TPERIOD REF Period Measurement at 1.5V 69.82033 69.86224 ns TPERIODAbs REF Absolute Period Measurement at 1.5V 68.83429 70.84826 ns THIGH REF High time Measurement at 2V 29.97543 38.46654 ns TLOW REF Low time Measurement at 0.8V 29.57543 38.26654 TR / TF REF Rising and Falling Edge Rate Measured between 0.8V and 2.0V 1.0 % ns 4.0 V/ns TSKEW REF Clock to REF Clock Measurement at 1.5V – 500 ps TCCJ REF Cycle to Cycle Jitter Measurement at 1.5V – 1000 ps LACC Long Term Accuracy Measurement at 1.5V – 100 ppm – 1.8 ms 10.0 – ns ENABLE/DISABLE and SET-UP TSTABLE Clock Stabilization from Power-up TSS Stopclock Set-up Time Test and Measurement Set-up For Single-ended Signals and Reference The following diagram shows test load configurations for the single-ended PCI, USB, and REF output signals. Figure 15.Single-ended Load Configuration Low Drive Option The information in this document is believed to be accurate in all respects at the time of publication but is subject to change without notice. Silicon Laboratories assumes no responsibility for errors and omissions, and disclaims responsibility for any consequences resulting from the use of information included herein. Additionally, Silicon Laboratories assumes no responsibility for the functioning of undescribed features or parameters. Silicon Laboratories reserves the right to make changes without further notice. Silicon Laboratories makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Silicon Laboratories assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. Silicon Laboratories products are not designed, intended, or authorized for use in applications intended to support or sustain life, or for any other application in which the failure of the Silicon Laboratories product could create a situation where personal injury or death may occur. Should Buyer purchase or use Silicon Laboratories products for any such unintended or unauthorized application, Buyer shall indemnify and hold Silicon Laboratories harmless against all claims and damages. .....................Document #: 001-05103 Rev *B Page 23 of 27 SL28647 Figure 16. Single-ended Load Configuration High Drive Option The following diagram shows the test load configuration for the differential CPU and SRC outputs. Figure 17. 0.8V Differential Load 3 .3 V s ig n a l s T DC - - 3 .3 V 2 .0 V 1 .5 V 0 .8 V 0V TR TF Figure 18. Single-ended Output Signals (for AC Parameters Measurement) .....................Document #: 001-05103 Rev *B Page 24 of 27 SL28647 Ordering Information Part Number Package Type Product Flow Lead-free SL28647CLC 72-pin QFN Commercial, 0 to 85C SL28647CLCT 72-pin QFN–Tape and Reel Commercial, 0 to 85C SL 28 647 CLC-(Y)T Packaging Designator for Tape and Reel Derivatives of a Generic Part Temperature Designator Package Designator L : QFN Revision Number A = 1st; B = 2nd ; C = 3th .... Generic Part Number Designated Family Number Company Initials This device is Pb free and RoHS compliant. Parts supporting extended temperature is available upon request. .....................Document #: 001-05103 Rev *B Page 25 of 27 SL28647 Package Diagram 72-Lead QFN 10 x 10 mm (Saw Version) The information in this document is believed to be accurate in all respects at the time of publication but is subject to change without notice. Silicon Laboratories assumes no responsibility for errors and omissions, and disclaims responsibility for any consequences resulting from the use of information included herein. Additionally, Silicon Laboratories assumes no responsibility for the functioning of undescribed features or parameters. Silicon Laboratories reserves the right to make changes without further notice. Silicon Laboratories makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Silicon Laboratories assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. Silicon Laboratories products are not designed, intended, or authorized for use in applications intended to support or sustain life, or for any other application in which the failure of the Silicon Laboratories product could create a situation where personal injury or death may occur. Should Buyer purchase or use Silicon Laboratories products for any such unintended or unauthorized application, Buyer shall indemnify and hold Silicon Laboratories harmless against all claims and damages. .....................Document #: 001-05103 Rev *B Page 26 of 27 SL28647 Document History Page Document Title: SL28647 Clock Generator for Intel®CK505 Document Number: 001-05103 REV. Issue Date Orig. of Change Description of Change 1.0 7/29/08 JMA New data sheet 1.1 3/30/09 JMA 1. Updated Package Diagram 2. Updated 27MHz Slew Rate Measurement Window 3. Updated TPeriod for CPU at 100MHz 4. MSL 1 to 2 5. Updated package drawing to be Saw 6. Updated Lead Width parameter b to be more visible .....................Document #: 001-05103 Rev *B Page 27 of 27