SL28770ELC

SL28770 EProClock® Generator for Intel Calpella Chipset Features • 96MHz Differential DOT clock • 27MHz Video clock • Intel CK505 Clock Revision 1.0 Compliant • Hybrid Video Support - Simultaneous DOT96, 27MHz_SS and 27MHz_NSS video clocks • 48MHz USB clock • Buffered Reference Clock 14.318MHz • PCI-Express Gen 2 Compliant • 14.318MHz Crystal Input or Clock input • Low power push-pull type differential output buffers • EProClock® Programmable Technology • Integrated voltage regulator • I2C support with readback capabilities • Integrated resistors on differential clocks • Triangular Spread Spectrum profile for maximum electromagnetic interference (EMI) reduction • Scalable low voltage VDD_IO (3.3V to 1.05V) • 3.3V Power supply • Wireless friendly 3-bits slew rate control on single-ended clocks. • 32-pin QFN package • Differential CPU clocks with selectable frequency • 100MHz Differential SRC clocks CPU SRC x2 x1 SATA DOT96 USB_48 REF 27M x1 x1 x1 x1 x2 • 100MHz Differential SATA clocks CKPWRGD/ PD# VSS_REF XOUT XIN/CLKIN VDD_REF REF0/ FS** SCLK SDATA Pin Configuration Block Diagram 32 31 30 29 28 27 26 25 24 VDD_CPU VDD_DOT 1 VSS_DOT 2 23 CPU0 22 CPU#0 DOT96 3 DOT96# 4 21 VSS_CPU SL28770 VDD_27 5 27_NSS 6 20 CPU1 19 CPU#1 18 VDD_CPU_IO 27_SS 7 USB_48 8 17 VDD_SRC CPU_STP# VDD_SRC_IO SRC#1 SRC1 VSS_SRC SRC0# / SATA# VSS_27 SRC0 / SATA 9 10 11 12 13 14 15 16 ** Internal 100K-ohm Pull-Down Resistor DOC#: SP-AP-0065 (Rev. AA) 400 West Cesar Chavez, Austin, TX 78701 1+(512) 416-8500 1+(512) 416-9669 Page 1 of 22 www.silabs.com SL28770 32-QFN Pin Definitions Pin No. 1 Name VDD_DOT Type PWR Description 3.3V Power supply for outputs and PLL 2 VSS_DOT 3 DOT96 O, DIF Fixed true 96MHz clock output GND Ground for outputs 4 DOT96# O, DIF Fixed complement 96MHz clock output 5 VDD_27 PWR 3.3V Power supply for 27MHz PLL Non-spread 27MHz video clock output 6 27M_NSS O,SE 7 27M_SS O, SE Spread 27MHz video clock output 8 USB_48 O,SE Non-spread 48MHz video clock output 9 VSS_27 GND Ground for 27MHz PLL 10 SRC0 / SATA O, DIF 100MHz True differential serial reference clock 11 SRC0# / SATA# O, DIF 100MHz Complement differential serial reference clock 12 VSS_SRC 13 SRC1 O, DIF 100MHz True differential serial reference clock GND 14 SRC1# O, DIF 100MHz Complement differential serial reference clock 15 VDD_SRC_IO 16 CPU_STP# I 17 VDD_SRC PWR 3.3V Power supply for PLL 18 VDD_CPU_IO PWR Scalable 3.3V to 1.05V power supply for output buffer 19 CPU1# O, DIF Complement differential CPU clock output 20 CPU1 O, DIF True differential CPU clock output 21 VSS_CPU 22 CPU0# O, DIF Complement differential CPU clock output 23 CPU0 O, DIF True differential CPU clock output 24 VDD_CPU 25 CKPWRGD/PD# PWR GND PWR I Ground for PLL Scalable 3.3V to 1.05V power supply for output buffer 3.3V tolerance input to stop the CPU clock Ground for PLL 3.3V Power supply for CPU PLL 3.3V LVTTL input. This pin is a level sensitive strobe used to latch the FS. After CKPWRGD (active HIGH) assertion, this pin becomes a real-time input for asserting power down (active LOW) 26 VSS_REF GND 27 XOUT O, SE 14.318MHz Crystal output, Float XOUT if using only CLKIN (Clock input) 28 XIN/CLKIN I 29 VDD_REF PWR 30 REF/FS** 14.318MHz Crystal input or 3.3V, 14.318MHz Clock Input 3.3V Power supply for outputs and also maintains SMBUS registers during power-down PD, I/O 3.3V tolerant input for Graphic clock selection/fixed 14.318MHz clock output. (Internal 100K-ohm pull-down resistor on FS pin) Refer to DC Electrical Specifications table for Vil_FS and Vih_FS specifications 31 SDATA I/O 32 SCLK I DOC#: SP-AP-0065 (Rev. AA) Ground for outputs SMBus compatible SDATA SMBus compatible SCLOCK Page 2 of 22 SL28770 PC EProClock® Programmable Technology PC EProClock® is the world’s first non-volatile programmable PC clock. The PC EProClock® technology allows board designer to promptly achieve optimum compliance and clock signal integrity; historically, attainable typically through device and/or board redesigns. PC EProClock® technology can be configured through SMBus or hard coded. - Differential skew control on true or compliment or both - Differential duty cycle control on true or compliment or both - Differential amplitude control - Differential and single-ended slew rate control Features: - Program Internal or External series resistor on single-ended clocks - > 4000 bits of configurations - Program different spread profiles - Can be configured through SMBus or hard coded - Program different spread modulation rate - Custom frequency sets Frequency Select Pin (FS) FS CPU Power On 0 133MHz Default 1 100MHz SRC SATA DOT96 USB_48 27MHz REF 100MHz 100MHz 96MHz 48MHz 27MHz 14.318MHz Frequency Select Pin FS Apply the appropriate logic levels to FS inputs before CKPWRGD assertion to achieve host clock frequency selection. When the clock chip sampled HIGH on CKPWRGD and indicates that VTT voltage is stable then FS input values are sampled. This process employs a one-shot functionality and once the CKPWRGD sampled a valid HIGH, all other FS, and CKPWRGD transitions are ignored except in test mode. Serial Data Interface To enhance the flexibility and function of the clock synthesizer, a two-signal serial interface is provided. Through the Serial Data Interface, various device functions, such as individual clock output buffers are individually enabled or disabled. The registers associated with the Serial Data Interface initialize to their default setting at power-up. The use of this interface is optional. Clock device register changes are normally made at system initialization, if any are required. The interface cannot be used during system operation for power management functions. Data Protocol The clock driver serial protocol accepts byte write, byte read, block write, and block read operations from the controller. For block write/read operation, access the bytes in sequential order from lowest to highest (most significant bit first) with the ability to stop after any complete byte is transferred. For byte write and byte read operations, the system controller can access individually indexed bytes. The offset of the indexed byte is encoded in the command code described in Table 1. The block write and block read protocol is outlined in Table 2 while Table 3 outlines byte write and byte read protocol. The slave receiver address is 11010010 (D2h). . Table 1. Command Code Definition Bit 7 Description 0 = Block read or block write operation, 1 = Byte read or byte write operation (6:0) Byte offset for byte read or byte write operation. For block read or block write operations, these bits should be '0000000' Table 2. Block Read and Block Write Protocol Block Write Protocol Bit 1 8:2 9 10 18:11 19 27:20 28 Description Start Slave address–7 bits Write Acknowledge from slave Command Code–8 bits Block Read Protocol Bit 1 8:2 9 10 18:11 Description Start Slave address–7 bits Write Acknowledge from slave Command Code–8 bits Acknowledge from slave 19 Acknowledge from slave Byte Count–8 bits 20 Repeat start Acknowledge from slave DOC#: SP-AP-0065 (Rev. AA) 27:21 Slave address–7 bits Page 3 of 22 SL28770 Table 2. Block Read and Block Write Protocol (continued) Block Write Protocol Bit 36:29 37 45:38 Description Data byte 1–8 bits Acknowledge from slave Data byte 2–8 bits Block Read Protocol Bit Read = 1 29 Acknowledge from slave 37:30 46 Acknowledge from slave .... Data Byte /Slave Acknowledges .... Data Byte N–8 bits .... Acknowledge from slave .... Stop Description 28 38 46:39 47 55:48 Byte Count from slave–8 bits Acknowledge Data byte 1 from slave–8 bits Acknowledge Data byte 2 from slave–8 bits 56 Acknowledge .... Data bytes from slave / Acknowledge .... Data Byte N from slave–8 bits .... NOT Acknowledge .... Stop Table 3. Byte Read and Byte Write Protocol Byte Write Protocol Bit 1 8:2 9 10 18:11 19 27:20 Description Start Slave address–7 bits Write Acknowledge from slave Command Code–8 bits Byte Read Protocol Bit 1 8:2 9 10 18:11 Description Start Slave address–7 bits Write Acknowledge from slave Command Code–8 bits Acknowledge from slave 19 Acknowledge from slave Data byte–8 bits 20 Repeated start 28 Acknowledge from slave 29 Stop 27:21 28 29 37:30 DOC#: SP-AP-0065 (Rev. AA) Slave address–7 bits Read Acknowledge from slave Data from slave–8 bits 38 NOT Acknowledge 39 Stop Page 4 of 22 SL28770 Control Registers Byte 0: Control Register 0 Bit @Pup Name Description 7 HW FS 6 0 RESERVED RESERVED 5 1 RESERVED RESERVED 4 0 iAMT_EN 3 0 RESERVED 2 0 SRC_Main_SEL 1 0 SATA_SEL Select source of SATA clock 0 = SATA = SRC_MAIN, 1= SATA = PLL4 0 1 PD_Restore Save configuration when PD# is asserted 0 = Config. cleared, 1 = Config. saved CPU Frequency Select Bit, set by HW 0 = 133MHz, 1= 100MHz iAMT Enable 0 = Legacy Mode, 1 = iAMT Enabled RESERVED Select source for SRC clock 0 = SRC_MAIN = PLL1, PLL3_CFG Table applies 1 = SRC_MAIN = PLL3, PLL3_CFG Table does not apply Byte 1: Control Register 1 Bit @Pup Name 7 1 RESERVED 6 0 PLL1_SS_DC Select for down or center SS 0 = Down spread, 1 = Center spread 5 0 PLL3_SS_DC Select for down or center SS 0 = Down spread, 1 = Center spread 4 0 PLL3_CFB3 3 0 PLL3_CFB2 2 1 PLL3_CFB1 1 0 PLL3_CFB0 0 1 RESERVED Description RESERVED CFB Bit [4:1] only applies when SRC_Main_SEL = 0 (Byte 0, bit 2 =0) See Table 4 on page 9 for Configuration. RESERVED Byte 2: Control Register 2 Bit @Pup Name 7 1 REF_OE Output enable for REF 0 = Output Disabled, 1 = Output Enabled Description 6 1 USB_48_OE Output enable for USB_48 0 = Output Disabled, 1 = Output Enabled 5 1 RESERVED RESERVED 4 1 RESERVED RESERVED 3 1 RESERVED RESERVED 2 1 RESERVED RESERVED 1 1 RESERVED RESERVED 0 1 RESERVED RESERVED Byte 3: Control Register 3 Bit @Pup Name 7 1 RESERVED RESERVED 6 1 RESERVED RESERVED DOC#: SP-AP-0065 (Rev. AA) Description Page 5 of 22 SL28770 Byte 3: Control Register 3 5 1 RESERVED RESERVED 4 1 RESERVED RESERVED 3 1 RESERVED RESERVED 2 1 RESERVED RESERVED 1 1 RESERVED RESERVED 0 1 RESERVED RESERVED Byte 4: Control Register 4 Bit @Pup Name 7 1 RESERVED Description 6 1 SATA_OE Output enable for SATA 0 = Output Disabled, 1 = Output Enabled 5 1 SRC_OE Output enable for SRC 0 = Output Disabled, 1 = Output Enabled 4 1 DOT96_OE Output enable for DOT96 0 = Output Disabled, 1 = Output Enabled 3 1 CPU1_OE Output enable for CPU1 0 = Output Disabled, 1 = Output Enabled 2 1 CPU0_OE Output enable for CPU0 0 = Output Disabled, 1 = Output Enabled 1 1 PLL1_SS_EN Enable PLL1s spread modulation, 0 = Spread Disabled, 1 = Spread Enabled 0 1 PLL3_SS_EN Enable PLL3s spread modulation 0 = Spread Disabled, 1 = Spread Enabled RESERVED Byte 5: Control Register 5 Bit @Pup Name 7 0 RESERVED RESERVED Description 6 0 RESERVED RESERVED 5 0 RESERVED RESERVED 4 0 RESERVED RESERVED 3 0 RESERVED RESERVED 2 0 RESERVED RESERVED 1 0 RESERVED RESERVED 0 0 RESERVED RESERVED Byte 6: Control Register 6 Bit @Pup Name 7 0 RESERVED RESERVED 6 0 RESERVED RESERVED 5 0 REF Bit1 4 0 RESERVED RESERVED 3 0 27MHz Bit 1 27MHz slew rate control (see Byte 13 for Slew Rate Bit 0 and Bit 2) 0 = High, 1 = Low 2 0 RESERVED RESERVED 1 0 RESERVED RESERVED DOC#: SP-AP-0065 (Rev. AA) Description REF slew rate control (see Byte 13 for Slew Rate Bit 0 and Bit 2) 0 = High, 1 = Low Page 6 of 22 SL28770 Byte 6: Control Register 6 0 0 RESERVED RESERVED Byte 7: Vendor ID Bit @Pup Name Description 7 0 Rev Code Bit 3 Revision Code Bit 3 6 1 Rev Code Bit 2 Revision Code Bit 2 5 0 Rev Code Bit 1 Revision Code Bit 1 4 0 Rev Code Bit 0 Revision Code Bit 0 3 1 Vendor ID bit 3 Vendor ID Bit 3 2 0 Vendor ID bit 2 Vendor ID Bit 2 1 0 Vendor ID bit 1 Vendor ID Bit 1 0 0 Vendor ID bit 0 Vendor ID Bit 0 Byte 8: Control Register 8 Bit @Pup Name 7 1 Device_ID3 RESERVED Description 6 0 Device_ID2 RESERVED 5 0 Device_ID1 RESERVED 4 0 Device_ID0 RESERVED 3 0 RESERVED RESERVED 2 0 RESERVED RESERVED 1 1 27M_non-SS_OE Output enable for 27M_non-SS 0 = Output Disabled, 1 = Output Enabled 0 1 27M_SS_OE Output enable for 27M_SS 0 = Output Disabled, 1 = Output Enabled Byte 9: Control Register 9 Bit @Pup Name 7 0 RESERVED RESERVED 6 0 RESERVED RESERVED 5 1 RESERVED RESERVED 4 0 TEST _MODE_SEL Test mode select either REF/N or tri-state 0 = All outputs tri-state, 1 = All output REF/N 3 0 TEST_MODE_ENTRY Allows entry into test mode 0 = Normal Operation, 1 = Enter test mode(s) 2 1 I2C_VOUT 1 0 I2C_VOUT 0 1 I2C_VOUT DOC#: SP-AP-0065 (Rev. AA) Description Amplitude configurations differential clocks I2C_VOUT[2:0] 000 = 0.30V 001 = 0.40V 010 = 0.50V 011 = 0.60V 100 = 0.70V 101 = 0.80V (default) 110 = 0.90V 111 = 1.00V Page 7 of 22 SL28770 Byte 10: Control Register 10 Bit @Pup Name Description 7 0 RESERVED RESERVED 6 0 RESERVED RESERVED 5 0 RESERVED RESERVED 4 0 RESERVED RESERVED 3 0 RESERVED RESERVED 2 0 RESERVED RESERVED 1 1 CPU1_STP_CTRL Enable CPU_STP# control of CPU1 0 = Free running, 1= Stoppable 0 1 CPU0_STP_CTRL Enable CPU_STP# control of CPU0 0 = Free running, 1= Stoppable Byte 11: Control Register 11 Bit @Pup Name Description 7 0 RESERVED RESERVED 6 0 RESERVED RESERVED 5 0 RESERVED RESERVED 4 0 RESERVED RESERVED 3 0 RESERVED 2 1 CPU1_iAMT_EN 1 1 PCI-e_GEN2 PCI-e_Gen2 Compliant 0 = non Gen2, 1= Gen2 Compliant 0 1 RESERVED RESERVED RESERVED CPU1 iAMT Clock Enabled 0 = Disabled, 1 = Enabled Byte 12: Byte Count Bit @Pup Name 7 0 BC7 6 0 BC6 5 0 BC5 4 0 BC4 3 1 BC3 2 1 BC2 1 1 BC1 0 1 BC0 Description Byte count register for block read operation. The default value for Byte count is 15. In order to read beyond Byte 15, the user should change the byte count limit.to or beyond the byte that is desired to be read. Byte 13: Control Register 13 Bit @Pup DOC#: SP-AP-0065 (Rev. AA) Name Description Page 8 of 22 SL28770 7 1 REF_Bit2 Drive Strength Control - Bit[2:0], Note: See Byte 6 Bit 5 for REF Slew Rate Bit 1 and 6 1 REF_Bit0 Byte 6 Bit 3 for 27MHz Slew Rate Bit 1 5 1 27MHz_NSS_Bit2 4 1 27MHz_NSS_Bit0 3 1 27MHz_SS_Bit2 2 1 27MHz_SS_Bit0 1 0 RESERVED 0 0 Wireless Friendly mode Normal mode default ‘101’ Wireless Friendly Mode default to ‘111’ RESERVED Wireless Friendly Mode 0 = Disabled, Default all single-ended clocks slew rate config bits to ‘101’ 1 = Enabled, Default all single-ended clocks slew rate config bits to ‘111’ Byte 14: Control Register 14 Bit @Pup Name Description 7 1 USB_48_Bit2 Drive Strength Control - Bit[2:0] , Note: REF Bit 1is located in Byte 6 Bit 5 and 27MHz 6 0 USB_48_Bit1 5 1 USB_48_Bit0 4 0 OTP_4 3 0 OTP_3 2 0 OTP_2 1 0 OTP_1 0 0 OTP_0 Bit 1 is located in Byte 6 Bit 3 Normal mode default ‘101’ Wireless Friendly Mode default to ‘111’ OTP_ID Identification for programmed device Table 4. Pin 6 and 7 Configuration Table B1b4 B1b3 B1b2 B1b1 Pin7 Pin 8 Spread (%) 0 0 0 0 N/A N/A N/A 0 0 0 1 N/A N/A N/A 0 0 1 0 27M_NSS 27M_SS -0.5% 0 0 1 1 27M_NSS 27M_SS -1% 0 1 0 0 27M_NSS 27M_SS -1.5% 0 1 0 1 27M_NSS 27M_SS -2% 0 1 1 0 27M_NSS 27M_SS -0.75V 0 1 1 1 27M_NSS 27M_SS -1.25% DOC#: SP-AP-0065 (Rev. AA) Page 9 of 22 SL28770 B1b4 B1b3 B1b2 B1b1 Pin7 Pin 8 Spread (%) 1 0 0 0 27M_NSS 27M_SS -1.75% 1 0 0 1 27M_NSS 27M_SS +/-0.5% 1 0 1 0 27M_NSS 27M_SS +/-0.75% 1 0 1 1 N/A N/A N/A 1 1 0 0 N/A N/A N/A 1 1 0 1 N/A N/A N/A 1 1 1 0 N/A N/A N/A 1 1 1 1 N/A N/A N/A . . Table 5. Output Driver Status during CPU_STP# CPU_STP# Asserted Single-ended Clocks Stoppable Differential Clocks SMBus OE Disabled Running Driven low Non stoppable Running Stoppable Clock driven high Clock driven low Clock# driven low Non stoppable Running Table 6. Output Driver Status All Single-ended Clocks All Differential Clocks w/o Strap w/ Strap Clock Clock# Low Hi-z Low Low PD# = 0 (Power down) Table 7. Crystal Recommendations Frequency (Fund) Cut Loading Load Cap Drive (max.) Shunt Cap (max.) Motional (max.) Tolerance (max.) Stability (max.) Aging (max.) 14.31818 MHz AT Parallel 0.1 mW 5 pF 0.016 pF 35 ppm 30 ppm 5 ppm 20 pF The SL28770 requires a Parallel Resonance Crystal. Substituting a series resonance crystal causes the SL28770 to operate at the wrong frequency and violates the ppm specification. For most applications there is a 300-ppm frequency shift between series and parallel crystals due to incorrect loading. Crystal Loading Crystal loading plays a critical role in achieving low ppm performance. To realize low ppm performance, use the total capacitance the crystal sees to calculate the appropriate capacitive loading (CL). Figure 1 shows a typical crystal configuration using the two trim capacitors. It is important that the trim capacitors are in series with the crystal. It is not true that load capacitors are in parallel with the crystal and are approximately equal to the load capacitance of the crystal. DOC#: SP-AP-0065 (Rev. AA) Figure 1. Crystal Capacitive Clarification Calculating Load Capacitors In addition to the standard external trim capacitors, consider the trace capacitance and pin capacitance to calculate the crystal loading correctly. Again, the capacitance on each side is in series with the crystal. The total capacitance on both side is twice the specified crystal load capacitance (CL). Trim capacitors are calculated to provide equal capacitive loading on both sides. Page 10 of 22 SL28770 PD# (Power down) Clarification The CKPWRGD/PD# pin is a dual-function pin. During initial power up, the pin functions as CKPWRGD. Once CKPWRGD has been sampled HIGH by the clock chip, the pin assumes PD# functionality. The PD# pin is an asynchronous active LOW input used to shut off all clocks cleanly before shutting off power to the device. This signal is synchronized internally to the device before powering down the clock synthesizer. PD# is also an asynchronous input for powering up the system. When PD# is asserted LOW, clocks are driven to a LOW value and held before turning off the VCOs and the crystal oscillator. PD# (Power down) Assertion Figure 2. Crystal Loading Example , Use the following formulas to calculate the trim capacitor values for Ce1 and Ce2. Load Capacitance (each side) Ce = 2 * CL – (Cs + Ci) PD# Deassertion Total Capacitance (as seen by the crystal) CLe = 1 1 ( Ce1 + Cs1 + Ci1 + 1 Ce2 + Cs2 + Ci2 When PD# is sampled LOW by two consecutive rising edges of CPU clocks, all single-ended outputs will be held LOW on their next HIGH-to-LOW transition and differential clocks must held LOW. When PD# mode is desired as the initial power on state, PD# must be asserted LOW in less than 10 s after asserting CKPWRGD. ) CL ................................................... Crystal load capacitance CLe .........................................Actual loading seen by crystal using standard value trim capacitors The power up latency is less than 1.8 ms. This is the time from the deassertion of the PD# pin or the ramping of the power supply until the time that stable clocks are generated from the clock chip. All differential outputs stopped in a three-state condition, resulting from are driven high in less than 300 s of PD# deassertion to a voltage greater than 200 mV. After the clock chip’s internal PLL is powered up and locked, all outputs are enabled within a few clock cycles of each clock. Figure 4 is an example showing the relationship of clocks coming up. Ce .....................................................External trim capacitors Cs ............................................. Stray capacitance (terraced) Ci .......................................................... Internal capacitance (lead frame, bond wires, etc.) Figure 3. Power Down Assertion Timing Waveform DOC#: SP-AP-0065 (Rev. AA) Page 11 of 22 SL28770 Figure 4. Power Down Deassertion Timing Waveform Figure 5. CKPWRGD Timing Diagram CPU_STP# Assertion CPU_STP# Deassertion The CPU_STP# signal is an active LOW input used for synchronous stopping and starting the CPU output clocks while the rest of the clock generator continues to function. When the CPU_STP# pin is asserted, all CPU outputs that are set with the SMBus configuration to be stoppable are stopped within two to six CPU clock periods after sampled by two rising edges of the internal CPUC clock. The final states of the stopped CPU signals are CPUT = HIGH and CPUC = LOW. The deassertion of the CPU_STP# signal causes all stopped CPU outputs to resume normal operation in a synchronous manner. No short or stretched clock pulses are produced when the clock resumes. The maximum latency from the deassertion to active outputs is no more than two CPU clock cycles. CPU_STP# CPUT CPUC Figure 6. CPU_STP# Assertion Waveform DOC#: SP-AP-0065 (Rev. AA) Page 12 of 22 SL28770 CPU_STP# CPUT CPUC CPUT Internal CPUC Internal Tdrive_CPU_STP#,10 ns>200 mV Figure 7. CPU_STP# Deassertion Waveform DOC#: SP-AP-0065 (Rev. AA) Page 13 of 22 SL28770 Absolute Maximum Conditions Parameter Description Condition VDD_3.3V Main Supply Voltage Functional VDD_IO IO Supply Voltage Functional VIN Input Voltage Relative to VSS TS Temperature, Storage Non-functional TA Temperature, Operating Ambient (Commercial) TA Min. Max. Unit – 4.6 V 3.465 V –0.5 4.6 VDC –65 150 °C Functional 0 85 °C Temperature, Operating Ambient (Industrial) Functional -40 85 °C TJ Temperature, Junction Functional – 150 °C ØJC Dissipation, Junction to Case JEDEC (JESD 51) – 20 °C/ W ØJA Dissipation, Junction to Ambient JEDEC (JESD 51) – 60 °C/ W ESDHBM ESD Protection (Human Body Model) JEDEC (JESD 22 - A114) 2000 – V UL-94 Flammability Rating UL (Class) Max. Unit 3.135 3.465 V 2.0 VDD + 0.3 V VSS – 0.3 0.8 V 2.2 – V V–0 Multiple Supplies: The Voltage on any input or I/O pin cannot exceed the power pin during power-up. Power supply sequencing is NOT required. DC Electrical Specifications Parameter Description VDD core 3.3V Operating Voltage VIH 3.3V Input High Voltage (SE) Condition 3.3 ± 5% VIL 3.3V Input Low Voltage (SE) VIHI2C Input High Voltage SDATA, SCLK VILI2C Input Low Voltage SDATA, SCLK VIH_FS FS Input High Voltage VIL_FS FS Input Low Voltage IIH Input High Leakage Current Except internal pull-down resistors, 0 < VIN < VDD IIL Input Low Leakage Current Except internal pull-up resistors, 0 < VIN < VDD VOH VOL 3.3V Output High Voltage (SE) IOH = –1 mA 3.3V Output Low Voltage (SE) IOL = 1 mA VDD IO Low Voltage IO Supply Voltage IOZ Min. – 1.0 V 0.7 VDD+0.3 V VSS – 0.3 0.35 V – 5 A –5 – A 2.4 – V – 0.4 V 1 3.465 V High-impedance Output Current –10 10 A CIN Input Pin Capacitance 1.5 5 pF COUT Output Pin Capacitance 6 pF LIN Pin Inductance – 7 nH VXIH Xin High Voltage 0.7VDD VDD V VXIL Xin Low Voltage 0 0.3VDD V IDD_PD Power Down Current – 1 mA IDD_3.3V Dynamic Supply Current All outputs enabled. SE clocks with 8” traces. Differential clocks with 7” traces. Loading per CK505 spec. – 70 mA IDD_VDD_IO Dynamic Supply Current All outputs enabled. SE clocks with 8” traces. Differential clocks with 7” traces. Loading per CK505 spec. – 25 mA DOC#: SP-AP-0065 (Rev. AA) Page 14 of 22 SL28770 AC Electrical Specifications Parameter Description Condition Min. Max. Unit 47.5 52.5 % 69.841 71.0 ns – 10.0 ns Crystal TDC XIN Duty Cycle The device operates reliably with input duty cycles up to 30/70 but the REF clock duty cycle will not be within specification TPERIOD XIN Period When XIN is driven from an external clock source TR/TF XIN Rise and Fall Times Measured between 0.3VDD and 0.7VDD TCCJ XIN Cycle to Cycle Jitter As an average over 1-s duration – 500 ps LACC Long-term Accuracy Measured at VDD/2 differential – 250 ppm TDC CLKIN Duty Cycle Measured at VDD/2 47 53 % Clock Input TR/TF CLKIN Rise and Fall Times Measured between 0.2VDD and 0.8VDD 0.5 4.0 V/ns TCCJ CLKIN Cycle to Cycle Jitter Measured at VDD/2 – 250 ps TLTJ CLKIN Long Term Jitter Measured at VDD/2 – 350 ps VIL Input Low Voltage XIN / CLKIN pin – 0.8 V VIH Input High Voltage XIN / CLKIN pin 2 VDD+0.3 V IIL Input LowCurrent XIN / CLKIN pin, 0 < VIN