SC23R01T01002

SC23R01 8K-BIT CONTACTLESS IC CARD DESCRIPTION SC23R01 is a smart card module utilizing CMOS EEPROM technology. It is a multi-application functionality smart card with 1024 bytes EEPROM memory. Its embedded crypto and communication modules can protect the system fr om any kind of tampering and make it attractive in ticketing applications. FEATURES * 1024 X 8 bit EEPROM; * Operating frequency: 13.56MHz; baud rate: 106Kbit/s; * Contactless transmission of data and not need external power supply; * Operating distance: up to 10cm; * High security data transmission; * 16 independence sectors which support manifold applications; * For some key hierarchy system, each sector has two secret keys; * Customer definable access conditions for each memory block; * Arithmetic logic function; ORDERING INFORMATION Device SC23R01 SC23R01T-01-002 Package XOA2 Gold bump APPLICATIONS * High credible EEPROM controller, write endurance100000 cycles, * used for ticketing system with IC card. data retention of 10 years; * Comply to the ISO/IEC14443 type A. BLOCK DIAGRAM HANGZHOU SILAN MICROELECTRONICS CO.,LTD Http: www.silan.com.cn REV:1.1 2006.10.31 Page 1 of 7 SC23R01 PIN CONFIGURATION 1 RF1 RF2 2 XOA2 FUNCTION DESCRIPTION 1. RF interface and read/write device REQ STD/ALL 1.1 Request The communication protocol of SC23R01 is complied with the ISO14443A. When the card is positioned in the proximity of the read/write device (RWD), the RWD sends the REQ STD/ALL command to confirm whether the card is SC23R01. 1.2 Anti-collision loop When there are several cards in the operating rang of the RWD, the anticollision algorithm selects one card for further transaction. The unselected card return to the standby mode and wait for a new request command. In this course, it will return the serial number of the card. 1.3 Select card Select the serial number of the selected card, the card returns the answer to select code (=08H). 1.4 3 Pass authentication After selecting the card, the RWD specifies the memory location which needs access, and uses the corresponding key for 3 pass authentication. After authenticating successfully, all memory operations are encrypted. (for selecting another sector, the key should be authenticated again) . 1.5 Memory operations After authentication, the following operation may be performed: Read: read block. Write: write block. Decrement: decrease the content of a block and store the result in a data register. Increment: increase the content of a block and store the result in a data register. Transfer: write the content of data register to a value block. Restore: read the content of the value block to the data register. Halt: set the card in the halt mode. The operation flow chart: HANGZHOU SILAN MICROELECTRONICS CO.,LTD Http: www.silan.com.cn REV:1.1 2006.10.31 Page 2 of 7 SC23R01 2. Instruction Commands Code(hex) 26 52 93 93 60 61 30 A0 C1 C0 C2 B0 50 Request standby card Request all the cards in the operating range Anti-collision Select card Authentication key A Authentication key B Read Write Increment Decrement Restore Transfer Halt 3. Data integrity In the contactless communication, the following measures ensure the data transmission: l anti-collision l 16 bits CRC error correction for each frame HANGZHOU SILAN MICROELECTRONICS CO.,LTD Http: www.silan.com.cn REV:1.1 2006.10.31 Page 3 of 7 SC23R01 l parity bits for each byte l bit count checking l bit coding to distinguish between “ , “ or no information 1” 0” l channel monitoring(protocol sequence and bit stream analysis) 4. Security SC23R01 provides high security: three pass authentication is before read/write operation; each card has different serial number, ; transfer encrypted data and key protection. The secret key of the card is protected and cannot be read, which only the user knows and can amend it . The EEPROM is divided into 16 sectors, and each sector is with different key, user can set the key according to different sector (with multi-applications in one card). The RWD specifies the sector to be accessed only by verifying the key A or B. 5. Memory configuration and access condition The 8 k bits EEPROM is organized in 16 sectors with 4 blocks of 16 bytes each sector. Memory map: The block 3 of each sector contains the secret key A (6 bytes), access control condition (4 bytes) and secret key B(6 bytes), which is a specific block , other three blocks are data blocks; but the block 0 of the sector 0 used for store manufacture code and serial number, it is solidified and only readable. The data blocks can be configured two applications: read/write blocks and value blocks; the read/write block is used for store data, direct read and write; the value block is used for initialization, increment, decrement and value reading for direct control of the stored value. Block 3 configuration: HANGZHOU SILAN MICROELECTRONICS CO.,LTD Http: www.silan.com.cn REV:1.1 2006.10.31 Page 4 of 7 SC23R01 Access control of block 3 is as follows: Key A C1X3 C2X3 C3X3 0 0 1 1 0 0 1 1 0 1 0 1 0 1 0 1 0 0 0 0 1 1 1 1 Read Never Never Never Never Never Never Never Never Key A Write KEY A Never KEY B Never KEY A KEY B Never Never Access Control Read KEY A KEY A KEY A|B KEY A|B KEY A KEY A|B KEY A|B KEY A|B Access Control Write Never Never Never Never KEY A KEY B KEY B Never Key B Read KEY A KEY A Never Never KEY A Never Never Never Key B Write KEY A Never KEYB Never KEY A KEY B Never Never Key B may be read, transfer configuration Key B may be read Key B may be read Remark Note: KEYA|B indicates secret key A or key B; never denotes no condition implement. Data block storage control: C1XY 0 0 1 1 0 0 1 1 C2XY 0 1 0 1 0 1 0 1 C3XY 0 0 0 0 1 1 1 1 Read KEY A|B1 KEY A|B1 KEY A|B KEY A|B KEY B1 KEY B 1 1 1 Write KEY A|B1 Never KEY B KEY B 1 1 Increment KEY A|B1 Never Never KEY B 1 Decr, Transfer, Restore KEY A|B1 Never Never KEY A|B1 KEY A|B1 Never Never Never KEY A|B1 Never KEY B1 Never Never Never Never Never Never Never Note: if key B can be read in the sector trailer, then it cannot be as key authentication(all grey line in above table). If the RWD tries to authenticate any blocks with key B using gray line, the card will refuse any operation for memory after authentication. HANGZHOU SILAN MICROELECTRONICS CO.,LTD Http: www.silan.com.cn REV:1.1 2006.10.31 Page 5 of 7 SC23R01 PACKAGE OUTLINE XOA2 UNIT: mm MODULE HANDLING DESCRIPTION (ADVICE) • The substrate material of the card is PVC of 6 layers (Inlay 2 layers). • Antenna material: monocrystal Cu (enameled wire); antenna coil: 5 loops; linear diameter: Φ0.13mm; inside diameter: 44x75mm; outside diameter: 45 x76mm; the module and antenna adopt bonding technology. • The winding of the antenna coil makes the inductance to be 5.3~5.5µ in order to match the antenna with the module and make sure it will meet the requirement of resonance frequency and induction distance. HANDLING MOS DEVICES: Electrostatic charges can exist in many things. All of our MOS devices are internally protected against electrostatic discharge but they can be damaged if the following precautions are not taken: • Persons at a work bench should be earthed via a wrist strap. • Equipment cases should be earthed. • All tools used during assembly, including soldering tools and solder baths, must be earthed. • MOS devices should be packed for dispatch in antistatic/conductive containers. HANGZHOU SILAN MICROELECTRONICS CO.,LTD Http: www.silan.com.cn REV:1.1 2006.10.31 Page 6 of 7