SC5104

SC5104 FAN REMOTE CONTROL ENCODER DESCRIPTION SC5104 is a remote control encoder paired with SC8206 utilizing CMOS technology. Using a special coding technique, SC5104 increases noise immunity to a very great extent. SC5104 has a maximum of 8 input channel. Its high performance features makes SC5104 a must in every fan and other electrical home appliance remote control application. SOP-16-225-1.27 FEATURES * CMOS technology * High noise immunity * Wide range of voltage: Vcc=2.2 ~ 4.0 V * LED indicator * Transmits signal of maximum 8 channels * 2 bits custom code options available * Key-in oscillation, reduce static current dissipation. * 38kHz carrier transmits output. DIP-16-300-2.54 ORDERING INFORMATION Device SC5104 SC5104S Package DIP-16-300-2.54 SOP-16-225-1.27 APPLICATIONS * Fan remote control * Air cleaner * Humidifier * Heater BLOCK DIAGRAM HANGZHOU SILAN MICROELECTRONICS CO.,LTD Http: www.silan.com.cn REV:1.2 2009.05.05 Page 1 of 8 SC5104 ABSOLUTE MAXIMUM RATING (Tamb=25°C) Characteristics Supply Voltage Input/Output Voltage Power Dissipation Operating Temperature Storage Temperature Symbol VDD VIN PD Topr Tstg Ratings -0.3~6.0 VSS -0.3V~VDD+0.3V 500 -10 ~ +70 -40~+125 Unit V V mW °C °C DC CHARACTERISTICS (unless other specified, Tamb=25°C,VDD=3V) Characteristics Supply Voltage Symbol VDD -no load, oscillation is stopped, Static Power Dissipation ISB C1=C2=0 no load, oscillation is stopped, C1=C2=1 DOUT Output High Current DOUT Output Low Current High Input Voltage Low Input Voltage LED High Output Current LED Low Output Current Oscillation Frequency Pull-up resistor at C1, C2 Pull-up resistor at K1~K8 IOH IOL VIH VIL IOH IOL fOSC Rc Ri VIN=0V VIN=0V VOH=2.7V VOL=0.3V --VOH=2.7V VOL=0.3V Test conditions Min. 2.0 ----0.7VDD 0 -----Typ. 3.0 0.1 1.8 0.74 -2.5 --2.5 -1.0 455 4 250 Max. 4.0 ----VDD 0.3VDD 10 ----Unit V μA μA mA mA V V mA mA kHz MΩ KΩ PIN CONFIGURATION C1 C2 K1 K2 K3 K4 K5 VSS 1 2 3 16 VDD 15 DOUT 14 LED SC5104 4 5 6 7 8 13 OSCO 12 OSCI 11 K8 10 K7 9 K6 HANGZHOU SILAN MICROELECTRONICS CO.,LTD Http: www.silan.com.cn REV:1.2 2009.05.05 Page 2 of 8 SC5104 PIN DESCRIPTION Pin no. 1~2 3~7 8 9~11 12 13 14 15 16 Symbol C1, C2 K1~K5 VSS K6~K8 OSCI OSCO LED DOUT VDD I/O I I -I I O O O -Floating Denote “0”. Key Input Pins, Built In Pull-Up Resistor. Negative Power Supply. Key Input Pins, Built In Pull-Up Resistor. 455kHz Oscillator Input Pin. 455kHz Oscillator Output Pin. LED Driver Output Indication Code Data Output(Contain 38kHz Carrier Signal) Positive Power Supply. Descriptions Custom Code Option: Built In Pull-Up Resistor, Grounding Denote “1”, FUNCTION DESCRIPTIONS 1. Key inputs K1~K8 In static mode, key inputs K1~K8 are set as high level through pull-up resistor and there is no current flows in circuit. When one key is pressed, corresponding code is transmitted. 2. Customer code C1, C2 In static mode, C1 and C2 are internal pulled as high level. Four different customer code combination are available by the two bits. For these two bits, “1” indicates corresponding pin is grounded while “0” indicates floating or connected to VDD. 3. Code format A frame consists of: 1） Lead code——110 2） Customer code——C1C2 3） Instruction code——7 bits key code (see SC5104 key code table for details) 4）Logic 0: 1/4T high level, 3/4T low level; Logic 1: 3/4T high level, 1/4T Low level. 5）Code cyclic time T=1.6879ms 6）Intern\val between two frame: 4T HANGZHOU SILAN MICROELECTRONICS CO.,LTD Http: www.silan.com.cn REV:1.2 2009.05.05 Page 3 of 8 SC5104 4. Data out Data code is output at Dout. When one key is pressed, high level is output at pin LED and data (four frames at least) is output at Dout after 32ms delay. Data is continuously output if the key is kept pressed and there is 4 code interval between frames. 5. Oscillator Internal oscillator integrates advanced key-press start power saving function. The oscillator is in sleep mode when there is no key pressed and there is no current; it only works when key is pressed. This is for power saving. 455KHz oscillator is connected to pins OSCI and OSCO for using. 6. Key code table Key No. K1 K2 K3 K4 K5 K6 K7 K8 Instruction code D0 0 0 0 0 0 0 1 1 D1 0 0 0 0 0 1 0 0 D2 0 0 0 0 1 0 0 0 D3 0 0 0 1 0 0 0 00 D4 0 0 1 0 0 0 0 1 D5 0 1 0 0 0 0 1 1 D6 1 0 0 0 0 0 1 0 HANGZHOU SILAN MICROELECTRONICS CO.,LTD Http: www.silan.com.cn REV:1.2 2009.05.05 Page 4 of 8 SC5104 TYPICAL APPLICATION CIRCUIT HANGZHOU SILAN MICROELECTRONICS CO.,LTD Http: www.silan.com.cn REV:1.2 2009.05.05 Page 5 of 8 SC5104 PACKAGE OUTLINE DIP-16-300-2.54 UNIT: mm SOP-16-225-1.27 1.80MAX UNIT: mm 1.27 10.15±0.25 0.4 0.2 +0.05 -0.02 HANGZHOU SILAN MICROELECTRONICS CO.,LTD Http: www.silan.com.cn REV:1.2 2009.05.05 Page 6 of 8 5.72±0.25 6.0±0.4 3.9±0.3 SC5104 HANDLING MOS DEVICES: Electrostatic charges can exist in many things. All of our MOS devices are internally protected against electrostatic discharge but they can be damaged if the following precautions are not taken: • Persons at a work bench should be earthed via a wrist strap. • Equipment cases should be earthed. • All tools used during assembly, including soldering tools and solder baths, must be earthed. • MOS devices should be packed for dispatch in antistatic/conductive containers. Disclaimer: • Silan reserves the right to make changes to the information herein for the improvement of the design and performance without further notice! • All semiconductor products malfunction or fail with some probability under special conditions. When using Silan products in system design or complete machine manufacturing, it is the responsibility of the buyer to comply with the safety standards strictly and take essential measures to avoid situations in which a malfunction or failure of such Silan products could cause loss of body injury or damage to property. • Silan will supply the best possible product for customers! HANGZHOU SILAN MICROELECTRONICS CO.,LTD Http: www.silan.com.cn REV:1.2 2009.05.05 Page 7 of 8