SC5262D-IR

Silan Semiconductors REMOTE CONTROL ENCODER DESCRIPTION The SC5262 is a remote control encoder paired with SC5272 utilizing CMOS technology. It encodes data and address pins into a serial coded waveform suitable for RF or IR modulation. SC5262 has a maximum of 12-bits of tri-state address pins providing up to 531,441(or 312) address codes; thereby, drastically reducing any code collision and unauthorized code scanning possibilities. SC5262 DIP-18 FEATURES * Low power consumption and very high noise immunity * Up to 12 tri-state code address pins or 6 data pins * Wide operating voltage range(Vcc=3V ~ 15V) * Single resistor oscillator * Latch or Momentary output type SOP-20 APPLICATION * Home/automation security system * Remote control toys or for industrial use * Remote control fan * Garage door controller DIP-20 ORDERING INFORMATION SC5262X-XX RF: RF Applicatant, normally omitted IR: IR Applicatant S: SOP-20 Package D: DIP-20 Package Omitted: DIP-18 Package PIN CONFIGURATION A0 A1 A2 A3 18 Pin Package 20 Pin Package A4 A5 A6/D5 A7/D4 Vss NC 1 Vcc Dout OSC1 OSC2 SC5262 TE A11/D0 A10/D1 A9/D2 A8/D3 NC HANGZHOU SILAN MICROELECTRONICS JOINT-STOCK CO.,LTD Rev: 1.0 2000.12.31 1 Silan Semiconductors BLOCK DIAGRAM OSC2 OSC1 TE Dout SC5262 14 17 15 16 18 Vcc OSC System Timing Control Logic Code Generation 9 Vss Address 1 A0 2 A1 3 A2 4 A3 5 A4 6 A5 7 A6/ D5 8 A7/ D4 10 A8/ D3 11 A9/ D2 12 13 A10/ A11/ D1 D0 The block diagram is for DIP-18(hereinafter is the same) ABSOLUTE MAXIMUM RATINGS(Ta=25°C ) Characteristic Supply Voltage Input Voltage Output Voltage Maximum Power Dissipation(Vcc=12V) Operating Temperature Storage Temperature Symbol Vcc Vi Vo Pa Topr Tstg Value -0.3 ~ 16.0 -0.3 ~ Vcc+0.3 -0.3 ~ Vcc+0.3 300 -20 ~ +70 -40 ~ +125 Unit V V V mW °C °C ELECTRICAL CHARACTERISTICS (Ta=25°C,Vcc=12V,unless otherwise specified) Characteristic Supply Voltage Supply Current Symbol Vcc Icc Test Condition Vcc=12V,OSC stops A0~ A11 Open Vcc=5V,VOH=3V Vcc=8V,VOH=4V Vcc=12V,VOH=6V Vcc=5V,VOL=3V Vcc=8V,VOL=4V Vcc=12V,VOL=6V Min 3 Typ. 0.02 Max 15 0.3 Unit V µA mA mA mA mA mA mA Dout Output driving Current IOH Dout Output sinking Current IOL -3 -6 -10 2 5 9 HANGZHOU SILAN MICROELECTRONICS JOINT-STOCK CO.,LTD Rev: 1.0 2000.12.31 2 Silan Semiconductors PIN DESCRIPTION Pin No. 18 PIN 20 PIN 1~6 1~6 SC5262 I/O I Pin Name A0~A5 Description Code Address pins No. 0~5. These six tri-state pins are detected by SC5262 to determine the encoded waveform bit 0 ~bit 5. Each pin can be set to “0”,”1”,”f”(floating). Code Address pinsNo.6~11/data pins No.5~0. These six tri-state pins are detected by SC5262 to determine the encoded waveform bit 6 ~bit 11.When these pins are used as address pins, they can be set to “0”,”1”,”f”.When they are used as data pins ,they can be set only to “0”,”1”. Transmission Enable. Active Low Signal.SC5262 outputs the encoded waveform to DOUT when this pins is pulled to LOW. A resistor connected between Oscillator Pin No.1 these two pins determine the Oscillator Pin No.2 fundamental frequency of SC5262. Data Output Pin. The encoded waveform is serially outputted to this pin. When SC5262 is not transmitting, DOUT outputs low(Vss) voltage. Positive Power Supply Negative Power Supply Not Connected 7~8 10~13 7~8 12~15 A6/D5~A11/D0 I 14 15 16 17 18 9 -- 16 17 18 19 20 9 10~11 TE I O I O ---- OSC1 OSC2 DOUT Vcc Vss NC FUNCTIONAL DESCRIPTION The SC5262 encodes the code address and data set at A0~ A5 and A6/D5 ~ A11/D0 into a special waveform and outputs it to the Dout when TE is pulled to “0” (Low state). This waveform is fed to either the RF modulator or the IR transmitter for transmission. The Transmitted radio frequency or infrared ray is received by the RF demodulator or IR receiver and reshaped to the special waveform. SC5272 is then used to decode the waveform and set the corresponding output pins. Thus completing a remote control encoding and decoding function. 1. RF OPERATION Code Bits A code bit is the basic component of the encoded waveform, and can be classified as either an AD(Address/Data) Bit or a SYNC(Synchronous) Bit. An AD bit can be designated as bit “ 0 ”, “ 1 ” or “ f ” if it is in low, high or floating state respectively. One bit waveform consists of two pulse cycles. Each pulse cycle has 16 oscillating time periods. For further details, please refer to the diagram below: The Synchronous bit waveform is 4 bits long with 1/8 bit width pulse. Please refer to the diagram below: 1/8 bit width=4a 4 bit width=128a Note: 1bit =32a HANGZHOU SILAN MICROELECTRONICS JOINT-STOCK CO.,LTD Rev: 1.0 2000.12.31 3 Silan Semiconductors Code word SC5262 A group of Code Bits is called a Code Word. A Code Word consists of 12 AD bits followed by one Sync. Bit. The 12 AD bits are determined by the corresponding states of A0~A5 and A6/D5 ~ A11/D0 pins at the time of transmission. When Data Type of SC5262 is used , the address bits will decrease accordingly. For example, in the 3 Data Type where the address has 9 bits, the transmitting format is: 9 address bits 3 Data bits Sync. Bit SC5262/SC5272 has a maximum of 12 Address Bits including the 6 Address/Data bits. The following diagram shows the code bits with their corresponding pins. A0 A1 A2 A3 A4 A5 A6 /D5 A6 A6 A6 A6 A6 A6 D5 A7 /D4 A7 A7 A7 A7 A7 D4 D4 A8 /D3 A8 A8 A8 A8 D3 D3 D3 A9 /D2 A9 A9 A9 D2 D2 D2 D2 A10 /D1 A10 A10 D1 D1 D1 D1 D1 A11 /D0 A11 D0 D0 D0 D0 D0 D0 Sync Sync Sync Sync Sync Sync Sync 0 Data 1 Data 2 Data 3 Data 4 Data 5 Data 6 Data A0 A0 A0 A0 A0 A0 A0 A1 A1 A1 A1 A1 A1 A1 A2 A2 A2 A2 A2 A2 A2 A3 A3 A3 A3 A3 A3 A3 A4 A4 A4 A4 A4 A4 A4 A5 A5 A5 A5 A5 A5 A5 The Code Bits A0~A5 and A6/D5 ~ A11/D0 are determined by the states of A0 ~ A5 and A6/D5 ~A11/D0 pins. For example, when the A0(pin 1) is set to “ 1 ”(Vcc), the code bit A0 is synthesized as “ 1 ” bit. In the same manner, when it (A0 pin) is set to “ 0 ”( Vss) or left floating, the Code Bit A0 is synthesized as a “ 0 ” or “ f ” bit respectively. Code Frame A Code Frame consists of 4 continuous code Words. When SC5262 detects “0” on the TE (meaning , the TE is active “low”), it outputs a Code frame at Dout. If TE is still active at the time the Code Frame transmission ends. SC5262 outputs another Code Frame. It should be noted that the Code Frame is synthesized at the time of transmission. TE 1 frame(=4 word) 1 frame 1 frame Dout Single Resistor Oscillator The Build-in oscillator circuitry of SC5262 allows a precision oscillator to be constructed by connecting an external resistor between OSC1 and OSC2 pins. For SC5272 to decode correctly the received waveform, the oscillator frequency of SC5272 must be 2.5 ~8 times that of transmitting SC5262. The typical oscillator frequency with various resistor values for both SC5262 and SC5272 are shown below: HANGZHOU SILAN MICROELECTRONICS JOINT-STOCK CO.,LTD Rev: 1.0 2000.12.31 4 Silan Semiconductors Encoder OSC Frequency 100 1000 SC5262 Decoder OSC Frequency R=100k R=240k R=510k R=1M Frequency (kHz) R=2M R=3.3M 10 Frequency (kHz) 100 R=510k R=1M R=2M R=4.7M 10 1 0 3 6 9 12 15 1 0 3 6 9 12 15 Supply Voltage (V) Supply Voltage (V) Suggested Oscillator resistor values are shown below: SC5262 4.7M 3.3M 1.2M SC5272 820k 680k 200k 2. IR OPERATION In the IR Type of operation, the functions are similar to the above descriptions except for the output waveform that has a carrier frequency of 38kHz. Details are as follow. Code Bits The Code Bits are further modulated with a 38kHz carrier frequency and can be”0”,”1” or “ f ” bit. Their waveform are shown below: OSC "0" "1" "f" Sync 620λ 20λ 60λ 160λ Note:λ=2 clock lengths Code Word A Code Word is made up of code bits and the format is the same as that of the RF Code Word. Code Frame Likewise, a Code Frame is made up of Code Words and the format is the same as that of RF type of operation. HANGZHOU SILAN MICROELECTRONICS JOINT-STOCK CO.,LTD Rev: 1.0 2000.12.31 5 Silan Semiconductors Oscillator SC5262 The oscillator frequency for the IR type of operation is twice the carrier frequency. Thus, the oscillator frequency should be kept at 76kHz. A 430k~470kΩ oscillator resistor between OSC1 and OSC2 pins is recommended. It should be noted that the carrier is a 50% duty cycle frequency. OPERATION FLOW CHART Power ON Stand-by Mode No TE Enable? Yes 4 Words of Address/Data transmitted No TE Enable? Yes HANGZHOU SILAN MICROELECTRONICS JOINT-STOCK CO.,LTD Rev: 1.0 2000.12.31 6 Silan Semiconductors TYPICAL APPLICATION CIRCUIT SW0 LED SW1 SW2 10µH 1N4148×4 2.7k ×4 SW3 SC5262 +12V 25pF 5pF 4.7M MPSH10 4.7k 10k ×4 18 17 16 15 14 13 12 11 10 SC5262 1 2 3 4 5 6 7 8 9 UHF Band 4 Data Transmitter Circuit is recommended. LED 10µH 25pF +12V 5pF 4.7M SW MPSH10 4.7k 18 17 16 15 14 13 12 11 10 SC5262 1 2 3 4 5 6 7 8 9 UHF Band Address-only(o data) Transmitter Circuit is recommended. HANGZHOU SILAN MICROELECTRONICS JOINT-STOCK CO.,LTD Rev: 1.0 2000.12.31 7 Silan Semiconductors LED 10µH SW SC5262 +12V 25pF 5pF 4.7M MPSH10 4.7k 18 17 16 15 14 13 12 11 10 SC5262 1 2 3 4 5 6 7 8 9 UHF Band Address-only(o data) Zero-stand-by Transmitter Circuit is recommended. SW0 SW1 SW2 SW3 1N4148×4 4.7 IR 47µF +4.5V Rosc 2SC1815×2 430k ~ 470k 18 17 16 15 14 13 12 11 10 2.7k ×4 SC5262-IR 1 1N4148 1N4148 SW4 SW5 2.7k 2 3 4 5 6 7 8 9 2.7k Infrared Ray 6-data circuit. Adjust Rosc to get 38kHz carrier pulse at Dout pin is recommended. HANGZHOU SILAN MICROELECTRONICS JOINT-STOCK CO.,LTD Rev: 1.0 2000.12.31 8 Silan Semiconductors PACKAGE OUTLINE SC5262 UNIT: mm 2.54 DIP-18-300-2.54 6.40 1.50 22.95 7.62 15 degree 3.51 0.46 DIP-20-300-2.54 2.54 3.30 5.08 0.25 UNIT: mm 6.40 1.50 22.95 7.62 15 degree 3.51 0.46 HANGZHOU SILAN MICROELECTRONICS JOINT-STOCK CO.,LTD Rev: 1.0 2000.12.31 9 3.30 5.08 0.25 Silan Semiconductors SOP-20-225-1.27 SC5262 UNIT: mm 10.45 7.70 1.27 18.02 17.62 0.41 HANGZHOU SILAN MICROELECTRONICS JOINT-STOCK CO.,LTD Rev: 1.0 2000.12.31 10 1.95 9.53