CLC2000ISO8MTR

Data Sheet Comlinear CLC2000, CLC4000 ® FEATURES n 9.4V pp output drive into RL= 25Ω n Using both amplifiers, 18.8V pp differential output drive into RL= 25Ω n ±200mA @ V = 9.4V o pp n 0.009%/0.06˚ differential gain/ phase error n 250MHz -3dB bandwidth at G = 2 n 510MHz -3dB bandwidth at G = 1 n 210V/μs slew rate n 4.5nV/√Hz input voltage noise n 2.7pA/√Hz input current noise n 7mA supply current n Fully specified at 5V and 12V supplies General Description APPLICATIONS n ADSL PCI modem cards n ADSL external modems n Cable drivers n Video line driver n Twisted pair driver/receiver n Power line communications Typical Application - ADSL Application The Comlinear CLC2000 and CLC4000 are dual and quad voltage feedback amplifiers that offer ±200mA of output current at 9.4Vpp. The CLC2000 and CLC4000 are capable of driving signals to within 1V of the power rails. When connected as a differential line driver, the amplifier drives signals up to 18.8Vpp into a 25Ω load, which supports the peak upstream power levels for upstream full-rate ADSL CPE applications. The Comlinear CLC2000 and CLC4000 can operate from single or dual supplies from 5V to 12V. It consumes only 7mA of supply current per channel. The combination of wide bandwidth, low noise, low distortion, and high output current capability makes the CLC2000 and CLC4000 ideally suited for Customer Premise ADSL or video line driving applications. +Vs + 1/2 CLC2000 Rf+ Ro+=12.5Ω Vo+ 1:2 VIN Rg RL=100Ω Rf- - VOUT Vo- Ro-=12.5Ω 1/2 CLC2000 -Vs Comlinear CLC2000, CLC4000 High Output Current Dual and Quad Amplifiers High Output Current Dual and Quad Amplifiers Rev 1D Ordering Information Part Number Package Pb-Free Operating Temperature Range Packaging Method CLC2000ISO8X SOIC-8 Yes -40°C to +85°C Reel CLC2000ISO8 SOIC-8 Yes -40°C to +85°C Rail CLC4000ISO14X SOIC-14 Yes -40°C to +85°C Reel CLC4000ISO14 SOIC-14 Yes -40°C to +85°C Rail Moisture sensitivity level for all parts is MSL-1. Exar Corporation 48720 Kato Road, Fremont CA 94538, USA www.exar.com Tel. +1 510 668-7000 - Fax. +1 510 668-7001 Data Sheet CLC2000 Pin Assignments CLC2000 Pin Configuration Pin Name 1 OUT1 Output, channel 1 OUT2 2 -IN1 Negative input, channel 1 -IN2 3 +IN1 Positive input, channel 1 4 -VS 5 +IN2 Positive input, channel 2 6 -IN2 Negative input, channel 2 7 OUT2 Output, channel 2 8 +VS 1 8 +VS -IN1 2 7 +IN1 3 6 -V S 4 +IN2 5 1 14 OUT4 -IN1 2 13 -IN4 +IN1 3 12 +IN4 +VS 4 11 -VS +IN2 5 10 +IN3 -IN2 6 9 -IN3 7 8 OUT3 OUT2 Negative supply Positive supply CLC4000 Pin Assignments CLC4000 Pin Configuration OUT1 Description Comlinear CLC2000, CLC4000 High Output Current Dual and Quad Amplifiers Pin No. OUT1 Pin No. Pin Name 1 OUT1 Description Output, channel 1 2 -IN1 Negative input, channel 1 3 +IN1 Positive input, channel 1 4 +VS Positive supply 5 +IN2 Positive input, channel 2 6 -IN2 Negative input, channel 2 7 OUT2 Output, channel 2 8 OUT3 Output, channel 3 9 -IN3 Negative input, channel 3 10 +IN3 Positive input, channel 3 11 -VS 12 +IN4 Negative supply Positive input, channel 4 13 -IN4 Negative input, channel 4 14 OUT4 Output, channel 4 Rev 1D ©2007-2013 Exar Corporation 2/18 Rev 1D Data Sheet Absolute Maximum Ratings The safety of the device is not guaranteed when it is operated above the “Absolute Maximum Ratings”. The device should not be operated at these “absolute” limits. Adhere to the “Recommended Operating Conditions” for proper device function. The information contained in the Electrical Characteristics tables and Typical Performance plots reflect the operating conditions noted on the tables and plots. Supply Voltage Input Voltage Range Min Max Unit 0 -Vs -0.5V ±7 or 14 +Vs +0.5V V V Comlinear CLC2000, CLC4000 High Output Current Dual and Quad Amplifiers Parameter Reliability Information Parameter Junction Temperature Storage Temperature Range Lead Temperature (Soldering, 10s) Package Thermal Resistance 8-Lead SOIC 14-Lead SOIC Min Typ -65 Max Unit 150 150 260 °C °C °C 100 88 °C/W °C/W Notes: Package thermal resistance (qJA), JDEC standard, multi-layer test boards, still air. ESD Protection Product Human Body Model (HBM) Charged Device Model (CDM) 2.5kV 2kV Recommended Operating Conditions Parameter Min Operating Temperature Range Supply Voltage Range -40 ±2.5 Typ Max Unit +85 ±6.5 °C V Rev 1D ©2007-2013 Exar Corporation 3/18 Rev 1D Data Sheet Electrical Characteristics TA = 25°C, Vs = 5V, Rf = Rg = 510Ω, RL = 100Ω to VS/2, G = 2; unless otherwise noted. Symbol Parameter Conditions Min Typ Max Units Frequency Domain Response -3dB Bandwidth G = +1, VOUT = 0.2Vpp, Rf = 0 422 MHz BWSS BWLS -3dB Bandwidth G = +2, VOUT = 0.2Vpp 236 MHz Large Signal Bandwidth G = +2, VOUT = 2Vpp 68 BW0.1dB MHz 0.1dB Gain Flatness G = +2, VOUT = 0.2Vpp 77 MHz Time Domain Response tR, tF Rise and Fall Time VOUT = 1V step; (10% to 90%) 3.7 ns tS Settling Time to 0.1% VOUT = 2V step 20 ns OS Overshoot VOUT = 0.2V step 6 % SR Slew Rate VOUT = 2V step 200 V/µs 2Vpp, 100KHz, RL = 25Ω -83 dBc 2Vpp, 1MHz, RL = 100Ω -85 dBc 2Vpp, 100KHz, RL = 25Ω -86 dBc 2Vpp, 1MHz, RL = 100Ω -82 dBc % Distortion/Noise Response HD2 2nd Harmonic Distortion HD3 3rd Harmonic Distortion DG Differential Gain NTSC (3.58MHz), DC-coupled, RL = 150Ω 0.01 DP Differential Phase NTSC (3.58MHz), DC-coupled, RL = 150Ω 0.05 ° en Input Voltage Noise > 1MHz 4.2 nV/√Hz in Input Current Noise > 1MHz 2.7 pA/√Hz XTALK Crosstalk Channel-to-channel 5MHz -63 dB DC Performance VIO Input Offset Voltage 0.3 mV dVIO Average Drift 0.383 µV/°C IIO Input Offset Current 0.2 µA Ib Input Bias Current 10 µA Average Drift 2.5 nA/°C 81 dB dIbni PSRR Power Supply Rejection Ratio DC AOL Open-Loop Gain RL = 25Ω 76 dB IS Supply Current per channel 6.75 mA Non-inverting 2.5 MΩ 1 pF 0.4 to 4.6 V 80 dB Input Characteristics RIN Input Resistance CIN Input Capacitance CMIR Common Mode Input Range CMRR Common Mode Rejection Ratio DC Output Characteristics RO ISC Closed Loop, DC 0.01 Ω RL = 25Ω 0.95 to 4.05 V RL = 1kΩ 0.75 to 4.25 V 1000 mA Output Voltage Swing Short-Circuit Output Current VOUT = VS / 2 ©2007-2013 Exar Corporation 4/18 Rev 1D Rev 1D VOUT Output Resistance Comlinear CLC2000, CLC4000 High Output Current Dual and Quad Amplifiers UGBW Data Sheet Electrical Characteristics TA = 25°C, Vs = 12V, Rf = Rg = 510Ω, RL = 100Ω to VS/2, G = 2; unless otherwise noted. Symbol Parameter Conditions Min Typ Max Units Frequency Domain Response -3dB Bandwidth G = +1, VOUT = 0.2Vpp, Rf = 0 510 MHz BWSS BWLS -3dB Bandwidth G = +2, VOUT = 0.2Vpp 250 MHz Large Signal Bandwidth G = +2, VOUT = 4Vpp 35 BW0.1dB MHz 0.1dB Gain Flatness G = +2, VOUT = 0.2Vpp 32 MHz 13.3 ns 20 ns Time Domain Response tR, tF Rise and Fall Time VOUT = 4V step; (10% to 90%) tS Settling Time to 0.1% VOUT = 2V step OS Overshoot VOUT = 0.2V step 2 % SR Slew Rate VOUT = 4V step 210 V/µs 2Vpp, 100KHz, RL = 25Ω -84 dBc 2Vpp, 1MHz, RL = 100Ω -86 dBc 8.4Vpp, 100KHz, RL = 25Ω -63 dBc 8.4Vpp, 1MHz, RL = 100Ω -82 dBc 2Vpp, 100KHz, RL = 25Ω -88 dBc 2Vpp, 1MHz, RL = 100Ω -80 dBc 8.4Vpp, 100KHz, RL = 25Ω -63 dBc Distortion/Noise Response HD2 2nd Harmonic Distortion HD3 3rd Harmonic Distortion DG Differential Gain DP 8.4Vpp, 1MHz, RL = 100Ω -83 dBc NTSC (3.58MHz), DC-coupled, RL = 150Ω 0.009 % Differential Phase NTSC (3.58MHz), DC-coupled, RL = 150Ω 0.06 ° en Input Voltage Noise > 1MHz 4.5 nV/√Hz in Input Current Noise > 1MHz 2.7 pA/√Hz Crosstalk Channel-to-channel 5MHz -62 dB XTALK DC Performance VIO dVIO Input Offset Voltage(1) -6 Average Drift 0.3 6 0.383 IIO Input Offset Current(1) 0.2 2 Ib Input Bias Current(1) 10 20 Average Drift 2.5 nA/°C 81 dB dIbni -2 mV µV/°C PSRR Power Supply Rejection Ratio(1) DC AOL Open-Loop Gain RL = 25 73 76 IS Supply Current(1) per channel 7 µA µA dB 12 mA Input Characteristics RIN Input Resistance CIN Input Capacitance CMIR Common Mode Input Range CMRR Common Mode Rejection Ratio(1) Non-inverting MΩ 1 pF 0.6 to 11.4 V 70 79 dB Closed Loop, DC 0.01 Ω RL = 25Ω (1) 1.5 1.2 to 10.8 DC Output Characteristics RO VOUT ISC Output Resistance Output Voltage Swing Short-Circuit Output Current 10.5 V RL = 1kΩ 0.8 to 11.2 V VOUT = VS / 2 1000 mA Notes: 1. 100% tested at 25°C ©2007-2013 Exar Corporation 5/18 Rev 1D Rev 1D 2.5 Comlinear CLC2000, CLC4000 High Output Current Dual and Quad Amplifiers UGBW Data Sheet Typical Performance Characteristics TA = 25°C, Vs = 12V, Rf = 510Ω, RL = 100Ω to VS/2, G = 2; unless otherwise noted. Non-Inverting Frequency Response (VS=5V) 1 2 0 1 Normalized Gain (dB) -1 G = 10 -2 G=2 G=5 -3 -4 G=1 Rf = 0 -5 -6 G=1 Rf = 0 0 -1 G = 10 G=5 -3 -4 -5 VOUT = 0.2Vpp -7 VOUT = 0.2Vpp -6 0.1 1 10 100 1000 0.1 1 Frequency (MHz) 10 1000 Inverting Frequency Response (VS=5V) 1 1 G = -1 0 G = -1 0 -1 -1 Normalized Gain (dB) G = -2 -2 G = -10 -3 -4 G = -5 -5 G = -2 -2 G = -10 -3 -4 G = -5 -5 -6 -6 VOUT = 0.2Vpp -7 VOUT = 0.2Vpp -7 0.1 1 10 100 1000 0.1 1 Frequency (MHz) 10 100 1000 100 1000 Frequency (MHz) Frequency Response vs. RL Frequency vs. RL (VS = 5V) 2 2 RL = 5kΩ 1 RL = 5kΩ 1 RL = 1kΩ Normalized Gain (dB) 0 -1 -2 RL = 150Ω -3 RL = 50Ω -4 -5 RL = 1kΩ 0 -1 -2 RL = 150Ω -3 RL = 50Ω -4 -5 VOUT = 0.2Vpp VOUT = 0.2Vpp RL = 25Ω -6 Rev 1D Normalized Gain (dB) 100 Frequency (MHz) Inverting Frequency Response Normalized Gain (dB) G=2 -2 RL = 25Ω -6 0.1 1 10 100 1000 0.1 Frequency (MHz) ©2007-2013 Exar Corporation 1 10 Frequency (MHz) 6/18 Comlinear CLC2000, CLC4000 High Output Current Dual and Quad Amplifiers Normalized Gain (dB) Non-Inverting Frequency Response Rev 1D Data Sheet Typical Performance Characteristics - Continued TA = 25°C, Vs = 12V, Rf = 510Ω, RL = 100Ω to VS/2, G = 2; unless otherwise noted. Frequency vs. CL Frequency vs. CL (VS = 5V) 1 0 0 CL = 1000pF Rs = 5Ω CL = 500pF Rs = 6Ω -2 -3 CL = 100pF Rs = 13Ω -4 CL = 50pF Rs = 20Ω -5 -6 CL = 1000pF Rs = 5Ω -1 Normalized Gain (dB) Normalized Gain (dB) -1 -3 CL = 100pF Rs = 13Ω -4 CL = 50pF Rs = 25Ω -5 -6 CL = 10pF Rs = 30Ω VOUT = 0.2Vpp CL = 500pF Rs = 6Ω -2 -7 VOUT = 0.2Vpp -7 0.1 1 10 100 1000 0.1 1 Frequency (MHz) 100 1000 Recommended RS vs. CL (VS = 5V) 45 40 35 30 RS (Ω) RS (Ω) 32 30 28 26 24 22 20 18 16 14 12 10 8 6 4 2 0 10 Frequency (MHz) Recommended RS vs. CL 25 20 15 10 VOUT = 0.2Vpp RS optimized for