SP3249E
Intelligent +3.0V to +5.5V RS-232 Transceiver
FEATURES
■ Meets true EIA/TIA-232-F Standards
from a +3.0V to +5.5V power supply
■ Interoperable with EIA/TIA-232 and
adheres to EIA/TIA-562 down to a +2.7V
power source
■ Minimum 250Kbps data rate under load
■ Regulated Charge Pump Yields Stable
RS-232 Outputs Regardless of VCC
Variations
■ Enhanced ESD Specifications:
+15kV Human Body Model
+15kV IEC61000-4-2 Air Discharge
+8kV IEC61000-4-2 Contact Discharge
C2+ 1
24 C1+
GND 2
23 V+
C2- 3
22 VCC
V- 4
T1OUT 5
T2OUT 6
21
SP3249E
C1-
20 T1 IN
19 T2 IN
18 T3 IN
T3 OUT 7
R1IN
8
17 R1OUT
R 2IN
9
16 R2OUT
T4OUT 10
15 T4IN
R3 IN 11
14
T5 OUT 12
13
R3 OUT
T5 IN
Now Available in Lead Free Packaging
DESCRIPTION
The SP3249E device is an RS-232 transceiver solution intended for portable or hand-held applications
such as notebook and palmtop computers. The SP3249E uses an internal high-efficiency, charge-pump
power supply that requires only 0.1µF capacitors in 3.3V operation. This charge pump and Exar's
driver architecture allow the SP3249E device to deliver compliant RS-232 performance from a single
power supply ranging from +3.0V to +5.5V. The SP3249E is a 5-driver / 3-receiver device that is ideal
for laptop / notebook computer and PDA applications.
Device
Power
Supplies
RS-232
Drivers
RS-232
Receivers
External
Components
Auto
On-Line
Circuitry
SELECTION TABLE
TTL 3-State
# of
Pins
SP3223E
+3.0V to +5.5V
2
2
4 Capacitors
YES
YES
20
SP3243E
+3.0V to +5.5V
3
5
4 Capacitors
YES
YES
28
SP3238E
+3.0V to +5.5V
5
3
4 Capacitors
YES
YES
28
SP3239E
+3.0V to +5.5V
5
3
4 Capacitors
NO
YES
28
SP3249E
+3.0V to +5.5V
5
3
4 Capacitors
NO
NO
24
Exar Corporation 48720 Kato Road, Fremont CA, 94538 • 510-668-7017 • www.exar.com
SP3249E_100_013111
ABSOLUTE MAXIMUM RATINGS
These are stress ratings only and functional operation
of the device at these ratings or any other above those
indicated in the operation sections of the specifications
below is not implied. Exposure to absolute maximum
rating conditions for extended periods of time may
affect reliability and cause permanent damage to the
device.
VCC.......................................................-0.3V to +6.0V
V+ (NOTE 1).......................................-0.3V to +7.0V
V- (NOTE 1)........................................+0.3V to -7.0V
V+ + |V-| (NOTE 1)...........................................+13V
ICC (DC VCC or GND current).........................+100mA
Input Voltages
TxIN, .................................................-0.3V to +6.0V
RxIN...................................................................+25V
Output Voltages
TxOUT.............................................................+13.2V
RxOUT........................................-0.3V to (VCC +0.3V)
Short-Circuit Duration
TxOUT....................................................Continuous
Storage Temperature......................-65°C to +150°C
NOTE 1: V+ and V- can have maximum magnitudes of 7V, but their absolute difference cannot exceed 13V.
ELECTRICAL CHARACTERISTICS
VCC = +3.0V to +5.5V, C1 - C4 = 0.1µF (tested at 3.3V +/-5%), C1 - C4 = 0.22µF (tested at 3.3V +/-10%),
C1 = 0.047µF and C2 - C4 = 0.33µF (tested at 5.0V +/-10%), TAMB = TMIN to TMAX, unless otherwise noted. Typical
values are at TA = 25°C
PARAMETER
MIN.
TYP.
MAX.
UNITS
CONDITIONS
0.3
1.0
mA
0.8
V
V
+1.0
µA
TxIN,TAMB = +25°C
0.4
V
IOUT = 1.6mA
DC CHARACTERISTICS
Supply Current
no load
LOGIC INPUTS AND RECEIVER OUTPUTS
Input Logic Threshold
LOW
HIGH
2.4
Input Leakage Current
+0.01
Output Voltage LOW
Output Voltage HIGH
VCC = +3.3V or +5.0V, TxIN
VCC -0.6
VCC -0.1
V
IOUT = -1.0mA
+5.0
+5.4
V
All driver outputs loaded with 3KΩ to
GND
DRIVER OUTPUTS
Output Voltage Swing
Exar Corporation 48720 Kato Road, Fremont CA, 94538 • 510-668-7017 • www.exar.com
SP3249E_100_013111
ELECTRICAL CHARACTERISTICS
VCC = +3.0V to +5.5V, C1 - C4 = 0.1µF (tested at 3.3V +/-5%), C1 - C4 = 0.22µF (tested at 3.3V +/-10%),
C1 = 0.047µF and C2 - C4 = 0.33µF (tested at 5.0V +/-10%), TAMB = TMIN to TMAX, unless otherwise noted. Typical
values are at TA = 25°C
PARAMETER
MIN.
TYP.
MAX.
UNITS
CONDITIONS
DRIVER OUTPUTS (continued)
Output Resistance
300
Output Short-Circuit Current
Ω
+35
+60
mA
25
V
VCC = V+ = V- = 0V, VOUT=+2V
VOUT = GND
RECEIVER INPUTS
Input Voltage Range
-25
Input Threshold LOW
0.6
1.2
V
Vcc = 3.3V
Input Threshold LOW
0.8
1.5
V
Vcc = 5.0V
Input Threshold HIGH
1.5
2.4
V
Vcc = 3.3V
Input Threshold HIGH
1.8
2.4
V
Vcc = 5.0V
7
kΩ
Input Hysteresis
0.5
Input Resistance
3
5
V
TIMING CHARACTERISTICS
Maximum Data Rate
250
kbps
RL = 3KΩ, CL = 1000pF, one
driver switching
Receiver Propagation Delay
tPHL
tPLH
0.15
0.15
µs
Receiver input to Receiver
output, CL = 150pF
Receiver Output Enable Time
200
ns
Normal operation
Receiver Output Disable Time
200
ns
Normal operation
Driver Skew
100
ns
| tPHL - tPLH |, TAMB = 25°C
Receiver Skew
50
Transition-Region Slew Rate
ns
30
V/µs
| tPHL - tPLH |
Vcc = 3.3V, RL = 3kΩ, TAMB =
25°C, measurements taken from
-3.0V to +3.0V or +3.0V to -3.0V
Exar Corporation 48720 Kato Road, Fremont CA, 94538 • 510-668-7017 • www.exar.com
SP3249E_100_013111
TYPICAL PERFORMANCE CHARACTERISTICS
Unless otherwise noted, the following performance characteristics apply for VCC = +3.3V, 250kbps data rate, all
drivers loaded with 3kΩ, 0.1µF charge pump capacitors, and TAMB = +25°C.
25
20
V /u S
6
V o lt
4
2
15
POS. SR
NE G S R
10
VOH
0
-2 0
1000
2000
3000
4000
5
VOL
5000
0
-4
0
-6
1000
2000
3000
4000
5000
pF
pF
Figure 2. Slew Rate VS. Load Capacitance
Figure 1. Transmitter Output Voltage VS. Load
Capacitance
60
50
mA
40
250K bps
30
120K bps
20K bps
20
10
0
0
1000
2000
3000
4000
5000
pF
Figure 3. Supply Current VS. Load Capacitance
when Transmitting Data
Exar Corporation 48720 Kato Road, Fremont CA, 94538 • 510-668-7017 • www.exar.com
SP3249E_100_013111
NAME
FUNCTION
PIN NUMBER
C2+
Positive terminal of the symmetrical charge-pump capacitor C2.
1
GND
Ground.
2
Negative terminal of the symmetrical charge-pump capacitor C2.
3
C2-
Regulated -5.5V output generated by the charge pump.
4
T1OUT
V-
RS-232 Driver Output.
5
T2OUT
RS-232 Driver Output.
6
T3OUT
RS-232 Driver Output.
7
R1IN
RS-232 receiver input.
8
R2IN
RS-232 receiver input.
9
T4OUT
RS-232 Driver Output.
10
R3IN
RS-232 receiver input.
11
T5OUT
RS-232 Driver Output.
12
TTL/CMOS driver input.
13
TTL/CMOS receiver output.
14
T5IN
R3OUT
TTL/CMOS driver input.
15
R2OUT
T4IN
TTL/CMOS receiver output.
16
R1OUT
TTL/CMOS receiver output.
17
T3IN
TTL/CMOS driver input.
18
T2IN
TTL/CMOS driver input.
19
T1IN
TTL/CMOS driver input.
20
C1-
Negative terminal of the symmetrical charge-pump capacitor C1.
21
Vcc
+3.0V to +5.5V supply voltage.
22
V+
Regulated +5.5V output generated by the charge pump.
23
Positive terminal of the symmetrical charge-pump capacitor C1.
24
C1+
Table 1. Device Pin Description
Exar Corporation 48720 Kato Road, Fremont CA, 94538 • 510-668-7017 • www.exar.com
SP3249E_100_013111
24 C1+
C2+ 1
GND 2
23
V+
C2- 3
22
VCC
V- 4
21
C1-
T1OUT 5
T2OUT
6
T3 OUT
7
SP3249E
20 T1 IN
19 T2 IN
18 T3 IN
R1IN
8
17 R1OUT
R 2IN
9
16
T4OUT 10
R3 IN
R2OUT
15 T4IN
11
14
T5 OUT 12
13
R3 OUT
T5 IN
Figure 4. SP3249E Pinout Configuration
C5
C1
C2
TTL/CMOS
INPUTS
+
+
+
24 C1+
0.1µF
VCC
22
VCC
0.1µF
V+
C3
21 C11 C2+
0.1µF
SP3249E
V-
C4
20 T1IN
T1OUT
5
19 T2IN
T2OUT
6
18 T3IN
T3OUT
7
15 T4IN
T4OUT
10
13 T5IN
T5OUT
12
R1IN
8
R2IN
9
R3IN
11
5kΩ
16 R2OUT
5kΩ
14 R3OUT
+
0.1µF
4
3 C2-
17 R1OUT
TTL/CMOS
OUTPUTS
23
+
0.1µF
RS-232
OUTPUTS
RS-232
INPUTS
5kΩ
GND
2
Figure 5. SP3249E Typical Operating Circuit
Exar Corporation 48720 Kato Road, Fremont CA, 94538 • 510-668-7017 • www.exar.com
SP3249E_100_013111
DESCRIPTION
Drivers
The SP3249E device meets the EIA/TIA-232
and ITU-T V.28/V.24 communication protocols
and can be implemented in battery-powered,
portable, or hand-held applications such as
notebook or palmtop computers. The SP3249E
devices feature Exar's proprietary and patented
(U.S.‑‑ 5,306,954) on-board charge pump circuitry that generates ±5.5V RS-232 voltage levels
from a single +3.0V to +5.5V power supply. The
SP3249E devices can guarantee a data rate of
250kbps fully loaded.
The drivers are inverting level transmitters that
convert TTL or CMOS logic levels to 5.0V EIA/
TIA-232 levels with an inverted sense relative
to the input logic levels. Typically, the RS-232
output voltage swing is +5.4V with no load and
+5V minimum fully loaded. The driver outputs are
protected against infinite short-circuits to ground
without degradation in reliability. These drivers
comply with the EIA-TIA-232-F and all previous
RS-232 versions.
The drivers can guarantee a data rate of 250kbps
fully loaded with 3kΩ in parallel with 1000pF,
ensuring compatibility with PC-to-PC communication software. All unused drivers inputs should
be connected to GND or VCC.
The SP3249E is a 5-driver/3-receiver device, ideal
for portable or hand-held applications.
The slew rate of the driver output is internally
limited to a maximum of 30V/µs in order to meet
the EIA standards (EIA RS-232D 2.1.7, Paragraph
5). The transition of the loaded output from HIGH
to LOW also meets the monotonicity requirements
of the standard.
THEORY OF OPERATION
The SP3249E device is made up of three basic
circuit blocks:
1. Drivers
2. Receivers
3. The Exar proprietary charge pump
Figure 7 shows a loopback test circuit used to
test the RS-232 drivers. Figure 8 shows the test
results of the loopback circuit with all five drivers
active at 120kbps with typical RS-232 loads in
parallel with 1000pF capacitors. Figure 9 shows
the test results where one driver was active
at 250kbps and all five drivers loaded with an
RS-232 receiver in parallel with a 1000pF capacitor. A solid RS-232 data transmission rate
of 120kbps provides compatibility with many
designs in personal computer peripherals and
LAN applications.
VCC
C5
C1
C2
+
+
+
RxD
UART
or
Serial µC
0.1µF
24 C1+
0.1µF
V+
23
C3
21 C11 C2+
0.1µF
22
VCC
SP3249E
C4
3 C220 T1IN
T1OUT 5
T2OUT 6
CTS
19 T2IN
18 T3IN
T3OUT 7
DCD
15 T4IN
T4OUT 10
RI
13 T5IN
T5OUT 12
RTS
16 R2OUT
14 R3OUT
+
0.1µF
RS-232
OUTPUTS
Receivers
The receivers convert +5.0V EIA/TIA-232
levels to TTL or CMOS logic output levels.
R1IN 8
17 R1OUT
DTR
0.1µF
V- 4
DSR
TxD
+
5kΩ
5kΩ
R2IN
9
RS-232
INPUTS
Since receiver input is usually from a transmission line where long cable lengths and system
interference can degrade the signal, the inputs
have a typical hysteresis margin of 300mV. This
ensures that the receiver is virtually immune to
noisy transmission lines. Should an input be left
unconnected, an internal 5kΩ pulldown resistor
to ground will commit the output of the receiver
to a HIGH state.
R3IN 11
5kΩ
GND
2
Figure 6. Interface Circuitry Controlled by
Microprocessor Supervisory Circuit
Exar Corporation 48720 Kato Road, Fremont CA, 94538 • 510-668-7017 • www.exar.com
SP3249E_100_013111
Charge Pump
The charge pump is an Exar–patented design
(U.S. 5,306,954) and uses a unique approach
compared to older less–efficient designs.
The charge pump still requires four external
capacitors, but uses a four–phase voltage
shifting technique to attain symmetrical 5.5V
power supplies. The internal power supply
consists of a regulated dual charge pump that
provides output voltages 5.5V regardless of
the input voltage (VCC) over the +3.0V to +5.5V
range. This is important to maintain compliant RS-232 levels regardless of power supply
fluctuations.
VCC
C5
C1
C2
+
+
+
0.1µF
C1+
0.1µF
LOGIC
INPUTS
LOGIC
OUTPUTS
V+
C1C2+
0.1µF
VCC
SP3249E
C3
+
0.1µF
VC4
C2-
+
0.1µF
TxOUT
TxIN
RxOUT
RxIN
1000pF
5kΩ
The charge pump operates in a discontinuous
mode using an internal oscillator. If the output
voltages are less than a magnitude of 5.5V, the
charge pump is enabled. If the output voltages
exceed a magnitude of 5.5V, the charge pump
is disabled. This oscillator controls the four
phases of the voltage shifting. A description of
each phase follows.
GND
Figure 7. Loopback Test Circuit for RS-232 Driver
Data Transmission Rates
Phase 1
— VSS charge storage — During this phase of the
clock cycle, the positive side of capacitors C1 and
C2 are initially charged to VCC. Cl+ is then switched
to GND and the charge in C1– is transferred to C2–.
Since C2+ is connected to VCC, the voltage potential
across capacitor C2 is now 2 times VCC.
Figure 8. Loopback Test results at 120kbps
(All Drivers Fully Loaded)
Figure 9. Loopback Test results at 250Kbps
(All Drivers Fully Loaded)
Exar Corporation 48720 Kato Road, Fremont CA, 94538 • 510-668-7017 • www.exar.com
SP3249E_100_013111
Phase 2
— VSS transfer — Phase two of the clock
connects the negative terminal of C2 to the VSS
storage capacitor and the positive terminal of
C2 to GND. This transfers a negative generated voltage to C3. This generated voltage is
regulated to a minimum voltage of -5.5V.
Simultaneous with the transfer of the voltage to C3,
the positive side of capacitor C1 is switched to VCC
and the negative side is connected to GND.
Phase 3
— VDD charge storage — The third phase of the
clock is identical to the first phase — the charge
transferred in C1 produces –VCC in the negative
terminal of C1, which is applied to the negative
side of capacitor C2. Since C2+ is at VCC, the voltage potential across C2 is 2 times VCC.
Since both V+ and V– are separately generated
from VCC, in a no–load condition V+ and V– will
be symmetrical. Older charge pump approaches
that generate V– from V+ will show a decrease in
the magnitude of V– compared to V+ due to the
inherent inefficiencies in the design.
The clock rate for the charge pump typically
operates at 500kHz. The external capacitors
can be as low as 0.1µF with a 16V breakdown
voltage rating.
Phase 4
— VDD transfer — The fourth phase of the clock
connects the negative terminal of C2 to GND,
and transfers this positive generated voltage
across C2 to C4, the VDD storage capacitor. This
voltage is regulated to +5.5V. At this voltage,
the internal oscillator is disabled. Simultaneous with the transfer of the voltage to C4, the
positive side of capacitor C1 is switched to VCC
and the negative side is connected to GND, allowing the charge pump cycle to begin again.
The charge pump cycle will continue as long
as the operational conditions for the internal
oscillator are present.
Figure 10. Charge Pump Waveform
Exar Corporation 48720 Kato Road, Fremont CA, 94538 • 510-668-7017 • www.exar.com
SP3249E_100_013111
VCC = +5V
C4
+5V
C1
+
+
C2
–
–5V
–
+
–
VDD Storage Capacitor
–
+
VSS Storage Capacitor
C3
–5V
Figure 11. Charge Pump — Phase 1
VCC = +5V
C4
+
C1
C2
–
+
–
+
–
–
+
VDD Storage Capacitor
VSS Storage Capacitor
C3
-5.5V
Figure 12. Charge Pump — Phase 2
VCC = +5V
C4
+5V
C1
+
–
C2
–5V
+
–
+
–
VDD Storage Capacitor
–
+
VSS Storage Capacitor
C3
–5V
Figure 13. Charge Pump — Phase 3
VCC = +5V
+5.5V
C1
+
–
C2
C4
+
–
+
–
–
+
VDD Storage Capacitor
VSS Storage Capacitor
C3
Figure 14. Charge Pump — Phase 4
Exar Corporation 48720 Kato Road, Fremont CA, 94538 • 510-668-7017 • www.exar.com
10
SP3249E_100_013111
VCC
C5
C1
+
+
24
0.1µF
C2
0.1µF
C1+
21 C11
+
22
VCC
0.1µF
3
C2+
SP3249E
V+
23
C3
V-
C2-
R1IN
8
R2IN
9
R3IN
11
20 T1IN
T1OUT
5
19 T2IN
T2OUT
6
18 T3IN
T3OUT
7
15 T4IN
T4OUT
10
13 T5IN
T5OUT
12
5kΩ
16 R2OUT
5kΩ
14 R3OUT
0.1µF
4
C4
17 R1OUT
+
+
0.1µF
5kΩ
6
7
8
9
GND
2
DB-9 Connector Pins:
1. Received Line Signal Detector
2. Received Data
3. Transmitted Data
4. Data Terminal Ready
5. Signal Ground (Common)
DB-9
Connector
6.
7.
8.
9.
1
2
3
4
5
DCE Ready
Request to Send
Clear to Send
Ring Indicator
Figure 15. Circuit for the connectivity of the SP3249E with a DB-9 connector
Exar Corporation 48720 Kato Road, Fremont CA, 94538 • 510-668-7017 • www.exar.com
11
SP3249E_100_013111
ESD Tolerance
most of the ESD current when the ESD source
is applied to the connector pins. The test circuit
for IEC61000-4-2 is shown on Figure 17. There
are two methods within IEC61000-4-2, the Air
Discharge method and the Contact Discharge
method.
The SP3249E device incorporates ruggedized
ESD cells on all driver output and receiver input
pins. The ESD structure is improved over our
previous family for more rugged applications
and environments sensitive to electro-static discharges and associated transients. The improved
ESD tolerance is at least +15kV without damage
nor latch-up.
With the Air Discharge Method, an ESD voltage
is applied to the equipment under test (EUT)
through air. This simulates an electrically charged
person ready to connect a cable onto the rear of
the system only to find an unpleasant zap just
before the person touches the back panel. The
high energy potential on the person discharges
through an arcing path to the rear panel of the
system before he or she even touches the system. This energy, whether discharged directly
or through air, is predominantly a function of
the discharge current rather than the discharge
voltage. Variables with an air discharge such as
approach speed of the object carrying the ESD
potential to the system and humidity will tend to
change the discharge current. For example, the
rise time of the discharge current varies with the
approach speed.
There are different methods of ESD testing applied:
a) MIL-STD-883, Method 3015.7
b) IEC61000-4-2 Air-Discharge
c) IEC61000-4-2 Direct Contact
The Human Body Model has been the generally
accepted ESD testing method for semi-conductors. This method is also specified in
MIL-STD-883, Method 3015.7 for ESD testing.
The premise of this ESD test is to simulate the
human body’s potential to store electro-static
energy and discharge it to an integrated circuit.
The simulation is performed by using a test
model as shown in Figure 16. This method
will test the IC’s capability to withstand an ESD
transient during normal handling such as in
manufacturing areas where the IC's tend to be
handled frequently.
The Contact Discharge Method applies the ESD
current directly to the EUT. This method was
devised to reduce the unpredictability of the ESD
arc. The discharge current rise time is constant
since the energy is directly transferred without the
air-gap arc. In situations such as hand held systems, the ESD charge can be directly discharged
to the equipment from a person already holding
the equipment. The current is transferred on to
the keypad or the serial port of the equipment
directly and then travels through the PCB and
finally to the IC.
The IEC-61000-4-2, formerly IEC801-2, is generally used for testing ESD on equipment and
systems. For system manufacturers, they must
guarantee a certain amount of ESD protection
since the system itself is exposed to the outside
environment and human presence. The premise
with IEC61000-4-2 is that the system is required
to withstand an amount of static electricity when
ESD is applied to points and surfaces of the
equipment that are accessible to personnel during normal usage. The transceiver IC receives
RS
RC
SW1
DC Power
Source
SW2
CS
Device
Under
Test
Figure 16. ESD Test Circuit for Human Body Model
Exar Corporation 48720 Kato Road, Fremont CA, 94538 • 510-668-7017 • www.exar.com
12
SP3249E_100_013111
Contact-Discharge Model
RS
RC
RV
SW1
SW2
Device
Under
Test
CS
DC Power
Source
R S and RV add up to 330Ω for IEC61000-4-2.
Figure 17. ESD Test Circuit for IEC61000-4-2
I→
The circuit models in Figures 16 and 17 represent
the typical ESD testing circuit used for all three
methods. The CS is initially charged with the DC
power supply when the first switch (SW1) is on.
Now that the capacitor is charged, the second
switch (SW2) is on while SW1 switches off. The
voltage stored in the capacitor is then applied
through RS, the current limiting resistor, onto the
device under test (DUT). In ESD tests, the SW2
switch is pulsed so that the device under test
receives a duration of voltage.
30A
15A
0A
For the Human Body Model, the current limiting
resistor (RS) and the source capacitor (CS) are
1.5kΩ an 100pF, respectively. For IEC-61000-4-2,
the current limiting resistor (RS) and the source capacitor (CS) are 330Ω an 150pF, respectively.
t = 0ns
t→
t = 30ns
Figure 18. ESD Test Waveform for IEC61000-4-2
The higher CS value and lower RS value in the
IEC61000-4-2 model are more stringent than the
Human Body Model. The larger storage capacitor injects a higher voltage to the test point when
SW2 is switched on. The lower current limiting
resistor increases the current charge onto the
test point.
Device PIN
TESTED
Driver Outputs
Receiver Inputs
Human Body
MODEL
Air Discharge
+15kV
+15kV
+15kV
+15kV
IEC61000-4-2
Direct Contact
Level
+8kV
+8kV
4
4
Table 3. Transceiver ESD Tolerance Levels
Exar Corporation 48720 Kato Road, Fremont CA, 94538 • 510-668-7017 • www.exar.com
13
SP3249E_100_013111
▲
▲
PACKAGE: 24 PIN TSSOP
e
Exar Corporation 48720 Kato Road, Fremont CA, 94538 • 510-668-7017 • www.exar.com
14
SP3249E_100_013111
ORDERING INFORMATION
Part Number
Temp. Range
Package
SP3249ECY-L
0C to +70C
24 Pin TSSOP
SP3249ECY-L/TR
0C to +70C
24 Pin TSSOP
SP3249EEY-L
-40C to +85C
24 Pin TSSOP
SP3249EEY-L/TR
-40C to +85C
24 Pin TSSOP
For Tape and Reel option add "/TR", Example: SP3249ECY-L/TR.
Exar Corporation 48720 Kato Road, Fremont CA, 94538 • 510-668-7017 • www.exar.com
15
SP3249E_100_013111
REVISION HISTORY
DATE
REVISION DESCRIPTION
02/28/05
--
01/31/11
1.0.0
Legacy Sipex Datasheet
Convert to Exar Format, Update ordering information and
change ESD specification to IEC61000-4-2
Notice
EXAR Corporation reserves the right to make changes to any products contained in this publication in order to improve design, performance or reliability. EXAR Corporation assumes no representation that the circuits are free of patent infringement. Charts and schedules contained herein are
only for illustration purposes and may vary depending upon a user's specific application. While the information in this publication has been carefully
checked; no responsibility, however, is assumed for inaccuracies.
EXAR Corporation does not recommend the use of any of its products in life support applications where the failure or malfunction of the product can
reasonably be expected to cause failure of the life support system or to significantly affect its safety or effectiveness. Products are not authorized for
use in such applications unless EXAR Corporation receives, in writing, assurances to its satisfaction that: (a) the risk of injury or damage has been
minimized ; (b) the user assumes all such risks; (c) potential liability of EXAR Corporation is adequately protected under the circumstances.
Copyright 2011 EXAR Corporation
Datasheet January 2011
For technical support please email Exar's Serial Technical Support group at : serialtechsupport@exar.com
Reproduction, in part or whole, without the prior written consent of EXAR Corporation is prohibited.
Exar Corporation 48720 Kato Road, Fremont CA, 94538 • 510-668-7017 • www.exar.com
16
SP3249E_100_013111
工商网监
湘ICP备2023018690号
