SP335E
RS-232/RS-485/RS-422 TRANSCEIVER WITH INTERNAL TERMINATION
August 2017
Rev. 1.0.2
GENERAL DESCRIPTION
FEATURES
Pin-Selectable Cable Termination
No External Resistors Required for RS-485/422
The SP335 is an advanced multiprotocol transceiver
supporting RS-232, RS-485, and RS-422 serial
standards. Integrated cable termination and multiple
configuration modes allow all three protocols to be
used interchangeably over a single cable or
connector with no additional switching components.
Full operation requires only four external charge
pump capacitors.
Termination or Biasing
Robust ESD Protection:
The RS-485/RS-232 mode pin selects RS-485 mode
when high, and RS-232 mode when low. In RS-485
mode, the TERM pin enables the differential 120
termination, and the HALF/FULL pin configures the
transceiver as either half or full duplex.
■
±15kV IEC 61000-4-2 Air Gap Discharge
■
± 8kV IEC 61000-4-2 Contact Discharge
■
±15kV Human Body Model (HBM)
20Mbps RS-485 and 1Mbps RS-232 Data Rates
Pin-Selectable 250kbps Slew Limiting
Single Supply Operation from 3V to 5.5V
1.65V to 5.5V Logic Interface VL pin
The high speed drivers operate up to 20Mbps in RS485/422 modes, and up to 1Mbps in RS-232 mode.
All drivers can be slew limited to 250kbps in any
mode to minimize electromagnetic interference (EMI)
by setting the dedicated SLEW pin low.
2 Drivers, 2 Receivers RS-232/V.28
1 Driver, 1 Receiver RS-485/422
All transmitter outputs and receiver inputs feature
robust electrostatic discharge (ESD) protection to
±15kV IEC 61000-4-2 Airgap, ±15kV Human Body
Model (HBM) and ±8kV IEC 61000-4-2 Contact. Each
receiver output has full fail-safe protection to avoid
system lockup, oscillation, or indeterminate states by
defaulting to logic-high output level when the inputs
are open, shorted, or terminated but undriven. No
external biasing resistors are required.
■
Full or Half Duplex Configuration
■
1/8th Unit Load, up to 256 receivers on bus
RS-485/422 Enhanced Receiver Fail-safe for open,
shorted, or terminated but idle inputs
10nA Shutdown Supply Current (typical)
Small 32 QFN package (5mm x 5mm)
TYPICAL APPLICATIONS
Software Programmable Serial Ports
The RS-232 receiver inputs include a 5k pull-down
to ground when in RS-232 mode. The RS-485/422
receiver inputs are high impedance (>96k when
termination is disabled), allowing up to 256 devices
on a single communication bus (1/8th unit load).
(RS-232, RS-422, RS-485)
Industrial and Single Board Computers
Industrial and Process Control Equipment
Point-Of-Sale Equipment
HVAC Controls and Networking Equipment
Building Security and Automation
The SP335 operates from a single power supply,
either 3.3V or 5V, with low idle current. The shutdown
mode consumes less than 1µA in low power standby
operation with RS-232 receivers enabled.
ORDERING INFORMATION(1)
PART NUMBER
OPERATING TEMPERATURE RANGE
LEAD-FREE
PACKAGE
SP335EER1-L
PACKAGE METHOD
Tray
-40°C to +85°C
SP335EER1-L/TR
Yes(2)
SP335ECR1-L
Reel
32-pin QFN
Tray
0°C to +70°C
SP335ECR1-L/TR
SP335EER1-0A-EB
Reel
SP335E Evaluation Board
NOTES:
1.
2.
Refer to www.exar.com/SP335E for most up-to-date Ordering Information
Visit www.exar.com for additional information on Environmental Rating
1
SP335E
RS-232/RS-485/RS-422 TRANSCEIVER WITH INTERNAL TERMINATION
REV. 1.0.2
ABSOLUTE MAXIMUM RATINGS
These are stress ratings only and functional operation of the device at these ratings or any other above those
indicated in the operation sections to the specifications below is not implied. Exposure to absolute maximum
rating conditions for extended periods of time may affect reliability and cause permanent damage to the
device.
Supply Voltage VCC
-0.3V to 6.0V
Logic Interface Voltage VL
VL VCC
Voltage at TTL Input Pins
-0.3V to 6.0V
Receiver Input Voltage (from Ground)
±18V
Driver Output Voltage (from Ground)
±18V
Short Circuit Duration, TX out to Ground
Continuous
Storage Temperature Range
-65°C to 150°C
Lead Temperature (soldering, 10s)
300°C
Maximum Operating Junction Temperature, TJ
125°C
Power Dissipation 32-pin 5x5 QFN
(derate 26.0mW/°C above +70°C)
1400mW
CAUTION:
ESD (ElectroStatic Discharge) sensitive device. Permanent damage may occur on unconnected devices
subject to high energy electrostatic fields. Unused devices must be stored in conductive foam or shunts.
Personnel should be properly grounded prior to handling this device. The protective foam should be
discharged to the destination socket before devices are removed.
ESD PROTECTION
MIN.
TYP.
TX Output & RX Input Pins
All Other Pins
2
MAX.
UNITS
±15
kV
IEC 61000-4-2 Airgap
±8
kV
IEC 61000-4-2 Contact
±15
kV
Human Body Model (HBM)
±3
kV
Human Body Model (HBM)
SP335E
RS-232/RS-485/RS-422 TRANSCEIVER WITH INTERNAL TERMINATION
REV. 1.0.2
ELECTRICAL CHARACTERISTICS
UNLESS OTHERWISE NOTED:
VCC = +3.0V to +5.5V, C1-C4 = 0.1µF; TA = TMIN to TMAX. Typical values are at VL = VCC = 3.3V, TA = +25°C.
SYMBOL
PARAMETERS
MIN.
TYP.
MAX.
UNITS
CONDITIONS
1
2.5
mA
No load, Idle inputs,
RS-485/RS-232 = 0V
DC CHARACTERISTICS
ICC
Supply Current (RS-232)
ICC
Supply Current (RS-485/422)
1.8
4.5
mA
No load, Idle inputs,
RS-485/RS-232 = VCC
ICC
Vcc Shutdown Current
0.01
1
µA
SHDN = 0V, Receiver inputs
open or grounded
TRANSMITTER and LOGIC INPUTS (PINS 10 - 15, 20 - 22)
VL
VIL
Logic Input Voltage Low
VIH
Logic Input Voltage High
IINL
Logic Input Leakage Current
±0.01
±1
µA
IINPD
Logic Input Pulldown Current
10
50
µA
VHYS
Logic Input Hysteresis
200
3
2VL
V
V
3
RE, TERM, & FD_TX_TERM
VIN = VL
mV
RS-232 and RS-485/422 RECEIVER OUTPUTS (PINS 6 & 7)
VOL
Receiver Output Voltage Low
VOH
Receiver Output Voltage High
IOSS
Receiver Output Short Circuit Current
IOZ
Receiver Output Leakage Current
0.4
VL-0.6
3
V
IOUT = 1.5mA
V
IOUT = -1.5mA
±20
±85
mA
±0.05
±1
µA
0 VO VL
0 VO VL,
Receivers disabled
SP335E
RS-232/RS-485/RS-422 TRANSCEIVER WITH INTERNAL TERMINATION
REV. 1.0.2
ELECTRICAL CHARACTERISTICS (Continued)
UNLESS OTHERWISE NOTED:
VCC = +3.0V to +5.5V, C1-C4 = 0.1µF; TA = TMIN to TMAX. Typical values are at VCC = 3.3V, TA = +25°C.
SYMBOL
PARAMETERS
MIN.
TYP.
MAX.
UNITS
+15
V
CONDITIONS
RS-232 SINGLE-ENDED RECEIVER INPUTS (PINS 18 & 19)
VIN
Input Voltage Range
VIL
Input Threshold Low
VIH
Input Threshold High
VHYS
Input Hysteresis
RIN
Input Resistance
-15
0.6
1.2
V
VCC = 3.3V
0.8
1.5
V
VCC = 5.0V
1.5
2.0
V
VCC = 3.3V
1.8
2.4
V
VCC = 5.0V
0.5
3
5
V
7
k
-15V VIN +15V
RS-232 SINGLE-ENDED TRANSMITTER OUTPUTS (PINS 3 & 4)
VOUT
Output Voltage Swing
±5.0
±5.5
V
Outputs loaded with 3k to Gnd
ROFF
Output Power Off Impedance
300
10M
VCC = 0V, VOUT = ±2V
ISC
Output Short Circuit Current
IO
Output Leakage Current
±30
4
±60
mA
±125
µA
VOUT = 0V
SHDN = 0V, VOUT = ±9V,
VCC = 0V or 5.5V
SP335E
RS-232/RS-485/RS-422 TRANSCEIVER WITH INTERNAL TERMINATION
REV. 1.0.2
ELECTRICAL CHARACTERISTICS (Continued)
UNLESS OTHERWISE NOTED:
VCC = +3.0V to +5.5V, C1-C4 = 0.1µF; TA = TMIN to TMAX. Typical values are at VCC = 3.3V, TA = +25°C.
SYMBOL
PARAMETERS
MIN.
TYP.
MAX.
UNITS
CONDITIONS
RS-485/422 DIFFERENTIAL RECEIVER INPUTS (A,B)
RIN
Receiver Input Resistance
IIN
Receiver Input Current
VTH
VTH
Receiver Differential
Threshold Voltage
k
96
-200
Receiver Input Hysteresis
-125
Termination disabled,
-7V VCM +12V
125
µA
VIN = +12V
-100
µA
VIN = -7V
-50
mV
-7V VCM +12V
25
mV
Termination enabled, Figure 4
RTERM
Termination Resistance
100
120
155
RTERM
Termination Resistance
100
120
140
Termination enabled, Figure 4
VCM = 0V
1.5
VCC
V
RL = 54 (RS-485), Figure 5
1.5
VCC
V
-7V VCM +12V, Figure 6
2
VCC
V
RL = 100 (RS-422), Figure 5
0.2
V
RL = 54 or 100, Figure 5
3
V
RL = 54 or 100, Figure 5
0.2
V
RL = 54 or 100, Figure 5
±250
mA
-7V VY or VZ +12V, Figure 7
µA
DE = 0V or SHDN = 0V,
VY or VZ = -7V or +12V,
-7V VCM +12V
RS-485/422 DIFFERENTIAL DRIVER OUTPUTS (Y, Z)
VOD
VOD
VCM
VCM
IOSD
IO
Differential Driver Output
Change In Magnitude of
Differential Output Voltage
Driver Common Mode Output Voltage
Change In Magnitude of
Common Mode Output Voltage
Driver Output Short Circuit Current
Driver Output Leakage Current
±125
VCC = 0V or 5.5V
5
SP335E
RS-232/RS-485/RS-422 TRANSCEIVER WITH INTERNAL TERMINATION
REV. 1.0.2
TIMING CHARACTERISTICS
UNLESS OTHERWISE NOTED:
VCC = +3.0V to +5.5V, C1-C4 = 0.1µF; TA = TMIN to TMAX. Typical values are at VCC = 3.3V, TA = +25°C.
SYMBOL
PARAMETERS
MIN.
TYP.
MAX.
UNITS
CONDITIONS
ALL MODES
tENABLE
tSHUTDOWN
Enable from Shutdown
1000
ns
Enable to Shutdown
1000
ns
RS-232, DATA RATE = 250kbps (SLEW = 0V), ONE TRANSMITTER SWITCHING
Maximum Data Rate
tRHL, tRLH
Receiver Propagation Delay
tRHL-tRLH
Receiver Propagation Delay Skew
tDHL, tDLH
Driver Propagation Delay
tDHL-tDLH
Driver Propagation Delay Skew
tSHL, tSLH
Transition Region Slew Rate from
3.0V to -3.0V or -3.0V to 3.0V
tSHL, tSLH
Transition Region Slew Rate from
3.0V to -3.0V or -3.0V to 3.0V
250
kbps
100
ns
100
1400
600
ns
RL = 3k, CL = 1000pF
CL = 150pF, Figure 8
ns
RL = 3k, CL = 2500pF,
ns
Figure 9
VCC = +3.3V, RL = 3k to 7k,
6
30
V/µs
CL = 150pF to 2500pF,
TA = 25°C, Figure 9
VCC = +3.3V, RL = 3k to 7k,
4
30
V/µs
CL = 150pF to 2500pF,
Figure 9
RS-232, DATA RATE = 1Mbps (SLEW = VCC), ONE TRANSMITTER SWITCHING
Maximum Data Rate
Mbps RL = 3k, CL = 250pF
1
tRHL, tRLH
Receiver Propagation Delay
tRHL-tRLH
Receiver Propagation Delay Skew
tDHL, tDLH
Driver Propagation Delay
tDHL-tDLH
Driver Propagation Delay Skew
tSHL, tSLH
Transition Region Slew Rate from
3.0V to -3.0V or -3.0V to 3.0V
13
Transition Region Slew Rate from
3.0V to -3.0V or -3.0V to 3.0V
24
tSHL, tSLH
100
ns
100
300
150
ns
CL = 150pF, Figure 8
ns
RL = 3k, CL = 1000pF,
ns
Figure 9
VCC = +3.3V, RL = 3k to 7k,
150
V/µs
CL = 150pF to 1000pF,
Figure 9
VCC = +3.3V, RL = 3k to 7k,
150
V/µs
CL = 150pF to 1000pF,
TA = 25°C, Figure 9
6
SP335E
REV. 1.0.2
RS-232/RS-485/RS-422 TRANSCEIVER WITH INTERNAL TERMINATION
TIMING CHARACTERISTICS (Continued)
UNLESS OTHERWISE NOTED:
VCC = +3.0V to +5.5V, C1-C4 = 0.1µF; TA = TMIN to TMAX. Typical values are at VCC = 3.3V, TA = +25°C.
SYMBOL
PARAMETERS
MIN.
TYP.
MAX.
UNITS
CONDITIONS
RS-485/RS-422, DATA RATE = 250kbps (SLEW = 0V), ONE TRANSMITTER SWITCHING
Maximum Data Rate
tRPHL, tRPLH
Receiver Propagation Delay
tRPHL-tRPLH
Receiver Propagation Delay Skew
tDPHL, tDPLH
Driver Propagation Delay
tDPHL-tDPLH
Driver Propagation Delay Skew
tDR, tDF
Driver Rise and Fall Time
250
kbps
50
500
300
650
150
ns
10
ns
1000
ns
100
ns
1200
ns
RL = 54, CL = 50pF
CL = 15pF, Figure 10
RL = 54, CL = 50pF,
Figure 11
tRZH, tRZL
Receiver Output Enable Time
200
ns
tRHZ, tRLZ
Receiver Output Disable Time
200
ns
tDZH, tDZL
Driver Output Enable Time
1000
ns
RL = 500, CL = 50pF,
tDHZ, tDLZ
Driver Output Disable Time
200
ns
Figure 13
CL = 15pF, Figure 12
RS-485/RS-422, DATA RATE = 20Mbps (SLEW = VCC), ONE TRANSMITTER SWITCHING
Maximum Data Rate
tRPHL, tRPLH
Receiver Propagation Delay
tRPHL-tRPLH
Receiver Propagation Delay Skew
tDPHL, tDPLH
Driver Propagation Delay
tDPHL-tDPLH
Driver Propagation Delay Skew
tDR, tDF
Mbps RL = 54, CL = 50pF
20
50
30
10
Driver Rise and Fall Time
150
ns
10
ns
100
ns
10
ns
20
ns
CL = 15pF, Figure 10
RL = 54, CL = 50pF,
Figure 11
tRZH, tRZL
Receiver Output Enable Time
200
ns
tRHZ, tRLZ
Receiver Output Disable Time
200
ns
tDZH, tDZL
Driver Output Enable Time
200
ns
RL = 500, CL = 50pF,
tDHZ, tDLZ
Driver Output Disable Time
200
ns
Figure 13
7
CL = 15pF, Figure 12
SP335E
RS-232/RS-485/RS-422 TRANSCEIVER WITH INTERNAL TERMINATION
REV. 1.0.2
PIN DESCRIPTIONS
Pin
Name
RS-232
RS-485 Full Duplex
RS-485 Half Duplex
1
2
GND
Ground
3
T1OUT, B/Z
Transmitter 1 Output
Z Driver Neg Output
B/Z Neg Input/Output
4
T2OUT, A/Y
Transmitter 2 Output
Y Driver Pos Output
A/Y Pos Input/Output
6
R1OUT
Receiver 1 Output
X
X
7
R2OUT, RO
Receiver 2 Output
Receiver TTL Output
Receiver TTL Output
5
8
9
10
SHDN
Low power shutdown mode when low
11
SLEW
Data rate limited to 250kbps when low
12
FD_TX_TERM
X
13
TERM
X
14
RS-485/RS-232
0
1
1
15
HALF/FULL
X
0
1
120 Y-Z termination
enabled when both TERM
and FD_TX_TERM are high
X
120 A-B termination enabled when high
16
17
GND
Ground
18
R2IN, A
Receiver 2 Input
A Pos Receiver Input
X
19
R1IN, B
Receiver 1 Input
B Neg Receiver Input
X
20
RE
X
Receiver enabled when low
21
T2IN, DE
Transmitter 2 Input
Driver enabled when high
22
T1IN, DI
Transmitter 1 Input
Driver TTL Input
23
24
25
V-
Charge pump negative supply, 0.1µF from ground
26
C2-
Charge pump cap 2 negative lead
27
C2+
Charge pump cap 2 positive lead, 0.1µF
28
V+
Charge pump positive supply, 0.1µF to ground
29
C1+
Charge pump cap 1 positive lead, 0.1µF
30
VL
Logic Supply for TTL Inputs and Outputs, VL = +1.65V to +5.5V or tie to VCC
31
VCC
Main Supply, VCC = +3.0V to +5.5V, bypass to ground with 1.0µF
32
C1-
Charge pump cap 1 negative lead
8
SP335E
RS-232/RS-485/RS-422 TRANSCEIVER WITH INTERNAL TERMINATION
REV. 1.0.2
SUGGESTED DB9 CONNECTOR PINOUT
DB9
Pin
RS-232
RS-485
Full Duplex
2
RXD
RX+
3
TXD
TX-
RS-485
Half Duplex
1
Data-
4
5
Ground
6
7
RTS
TX+
8
CTS
RX-
9
9
Data+
SP335E
RS-232/RS-485/RS-422 TRANSCEIVER WITH INTERNAL TERMINATION
REV. 1.0.2
BLOCK DIAGRAMS
FIGURE 1. RS-232 MODE
C1
0.1µF
C3
0.1µF
C2
0.1µF
C4
0.1µF
Cc
1.0µF
26
25
V-
V+
27
C2-
28
C2+
29
C1+
30
VL
31
VCC
C1-
32
1
24
SP335
GND
2
T1OUT
T2OUT
32 pin QFN
RS-232
23
T1
3
22
T2
4
21
5
R1
6
R2
7
5kΩ
19
5kΩ
18
GND
8
17
11
12
13
14
15
16
____
HALF/FULL
10
______
RS-485/RS-232
9
_____
SLEW
R2OUT
T2IN
20
_____
SHDN
R1OUT
T1IN
Pins 12, 13, and 20 have 300k internal pull-downs (not shown).
10
R1IN
R2IN
SP335E
RS-232/RS-485/RS-422 TRANSCEIVER WITH INTERNAL TERMINATION
REV. 1.0.2
FIGURE 2. RS-485 FULL DUPLEX MODE
C1
0.1µF
C3
0.1µF
C2
0.1µF
C4
0.1µF
Cc
1.0µF
27
26
25
V-
V+
C1+
28
C2-
29
C2+
30
VL
31
VCC
C1-
32
1
24
SP335
GND
2
Z
Y
RO
3
32 pin QFN
RS-485 Full Duplex
23
D
120Ω
22
4
21
5
20
6
19
R
120Ω
7
18
DI
DE
__
RE
B
A
GND
8
17
TERM
14
15
16
____
HALF/FULL
13
______
RS-485/RS-232
12
FD_TX_TERM
11
_____
SLEW
10
_____
SHDN
9
Pins 12, 13, and 20 have 300k internal pull-downs (not shown).
Termination control follows the truth table on page 20.
The full duplex driver termination is enabled only when both TERM and FD_TX_TERM are high.
11
SP335E
RS-232/RS-485/RS-422 TRANSCEIVER WITH INTERNAL TERMINATION
REV. 1.0.2
FIGURE 3. RS-485 HALF DUPLEX MODE
C1
0.1µF
C3
0.1µF
C2
0.1µF
C4
0.1µF
Cc
1.0µF
27
26
25
V-
V+
C1+
28
C2-
29
C2+
30
VL
31
VCC
C1-
32
1
24
SP335
GND
2
B/Z
A/Y
3
32 pin QFN
RS-485 Half Duplex
23
D
120Ω
22
4
21
5
20
6
7
18
GND
8
17
13
14
15
16
____
HALF/FULL
12
______
RS-485/RS-232
11
TERM
10
_____
SLEW
9
_____
SHDN
RO
19
R
Pins 12, 13, and 20 have 300k internal pull-downs (not shown).
Termination control follows the truth table on page 20.
12
DI
DE
__
RE
SP335E
RS-232/RS-485/RS-422 TRANSCEIVER WITH INTERNAL TERMINATION
REV. 1.0.2
TEST CIRCUITS
FIGURE 4. RS-485/422 RECEIVER TERMINATION RESISTANCE
IB
B
RTERM = 2 (VA – VB)
IA – IB
RTERM
±2V
Rx
IA
-7V ≤ VA, VB ≤ +12V
A
Termination is enabled when both TERM and RS-485/RS-232 are logic high.
FIGURE 5. RS-485/422 DIFFERENTIAL DRIVER OUTPUT VOLTAGE
Z
DI = 0V or VL
D
RL
2
VOD
VCM
RL
2
Y
DE = VL
FIGURE 6. RS-485/422 DIFFERENTIAL DRIVER OUTPUT VOLTAGE OVER COMMON MODE
Z
375Ω
DI = 0V or VL
D
VOD
VCM
60Ω
375Ω
Y
DE = VL
FIGURE 7. RS-485/422 DRIVER OUTPUT SHORT CIRCUIT CURRENT
Z
DI = 0V or VL
IOSD
D
-7V to +12V
Y
DE = 0V or VL
13
V
SP335E
RS-232/RS-485/RS-422 TRANSCEIVER WITH INTERNAL TERMINATION
REV. 1.0.2
FIGURE 8. RS-232 RECEIVER PROPAGATION DELAY
VIN
VOUT
Rx
CL
VIN
+3V
1.5V
1.5V
-3V
tRHL
tRLH
VL
2
VL
2
VOH
VOUT
VOL
FIGURE 9. RS-232 DRIVER PROPAGATION DELAY
VIN
VOUT
Tx
RL
VIN
VL
0V
VL
2
CL
VL
2
tDHL
tDLH
+3V
VOUT
0V
-3V
tSHL
0V
tSLH
14
SP335E
RS-232/RS-485/RS-422 TRANSCEIVER WITH INTERNAL TERMINATION
REV. 1.0.2
FIGURE 10. RS-485/422 RECEIVER PROPAGATION DELAY
B
RO
R
CL
A
RE = 0V
B
+1V
0V
-1V
A
tRPLH
tRPHL
VOH
VL
2
RO
VL
2
VOL
FIGURE 11. RS-485/422 DRIVER PROPAGATION DELAY AND RISE/FALL TIMES
Z
DI
VOD
D
RL
CL
Y
DE = VL
DI
VL
0V
Z
VL
2
VL
2
tDPLH
tSKEW = |tDPHL – tDPLH|
tDPHL
VOD
Y
VOD
(VY - VZ)
VOD+
0V
VOD-
90%
90%
10%
10%
tDR
15
tDF
SP335E
RS-232/RS-485/RS-422 TRANSCEIVER WITH INTERNAL TERMINATION
REV. 1.0.2
FIGURE 12. RS-485/422 RECEIVER OUTPUT ENABLE/DISABLE TIMES
B
RO
R
RE
A
RE
VL
0V
VL
2
RL
CL
VL
2
VA = VCC
VB = 0V
tRZH
VOH
tRHZ
VOH
2
RO
0V
VOH - 0.25V
VL
B
RL
RO
R
RE
VL
0V
VA = 0V
VB = VCC
VL
2
VL
2
tRZL
VL
RO
VOL
CL
RE
A
tRLZ
VL + VOL
2
VOL + 0.25V
16
SP335E
RS-232/RS-485/RS-422 TRANSCEIVER WITH INTERNAL TERMINATION
REV. 1.0.2
FIGURE 13. RS-485/422 DRIVER OUTPUT ENABLE/DISABLE TIMES
Z
Testing Z: DI = 0V
VOUT
D
Testing Y: DI = VL
DE
DE
VL
VL
2
0V
RL
Y
VL
2
tDZH
VOH
VOUT
CL
tDHZ
VOH + VOL
2
VOL
VOH - 0.25V
VCC
Z
RL
Testing Z: DI = VL
VOUT
D
Testing Y: DI = 0V
DE
DE
VL
0V
VL
2
VL
2
tDZL
VOH
VOUT
VOL
CL
Y
tDLZ
VOH + VOL
2
VOL + 0.25V
17
SP335E
RS-232/RS-485/RS-422 TRANSCEIVER WITH INTERNAL TERMINATION
REV. 1.0.2
PRODUCT SUMMARY
The SP335 is an advanced multiprotocol transceiver supporting RS-232, RS-485, and RS-422 serial
standards. Integrated cable termination and multiple configuration modes allow all three protocols to be used
interchangeably over a single cable or connector with no additional switching components. Full operation
requires only four external charge pump capacitors.
INTERNALLY SWITCHED CABLE TERMINATION
Enabling and disabling the RS-485/422 termination resistor is one of the largest challenges system designers
face when sharing a single connector or pair of lines across multiple serial protocols. A termination resistor
may be necessary for accurate RS-485/422 communication, but must be removed when the lines are used for
RS-232. SP335 provides an elegant solution to this problem by integrating the termination resistor and
switching control, and allowing it to be switched in and out of the circuit with a single pin. No external switching
components are required. Termination on the receiver inputs will be enabled if both TERM and RS-485/RS-232
are high.
ENHANCED FAILSAFE
The enhanced failsafe feature of the SP335 guarantees a logic-high receiver output when the receiver inputs
are open, shorted, or terminated but idle/undriven. The enhanced failsafe interprets 0V differential as a logic
high with a minimum 50mV noise margin, while maintaining compliance with the EIA/TIA-485 standard of
±200mV. No external biasing resistors are required, further easing the usage of multiple protocols over a single
connector.
±15kV ESD PROTECTION
ESD protection structures are incorporated on all pins to protect against electrostatic discharges encountered
during handling and assembly. The bus pins (driver outputs and receiver inputs) have extra protection
structures, which have been tested up to ±15kV without damage. These structures withstand high ESD in all
states: normal operation, in shutdown, and when powered off.
ESD protection is be tested in various ways. Exar uses the following methods to qualify the protection
structures designed into SP335:
±8kV using IEC 61000-4-2 Contact Discharge
±15kV using IEC 61000-4-2 Airgap Discharge
±15kV using the Human Body Model (HBM)
The IEC 61000-4-2 standard is more rigorous than HBM, resulting in lower voltage levels compared with HBM
for the same level of ESD protection. Because IEC 61000-4-2 specifies a lower series resistance, the peak
current is higher than HBM. The SP335 has passed both HBM and IEC 61000-4-2 testing without damage.
VARIABLE LOGIC LEVEL VOLTAGE
The SP335 includes a VL pin, which reduces the logic level thresholds to interface with processors operating at
reduced supply voltages. This pin should be connected to the supply voltage of the processor, or can be
connected to VCC for typical logic levels.
18
SP335E
RS-232/RS-485/RS-422 TRANSCEIVER WITH INTERNAL TERMINATION
REV. 1.0.2
TRUTH TABLES
TABLE 1: RS-232 TX TRUTH TABLE
INPUTS
OUTPUTS
SHDN
RS-485/RS-232
DI/T1IN, DE/T2IN
Z(B)/T1OUT, Y(A)/T2OUT
0
X
X
1/8th unit load
1
0
0
1
1
0
1
0
1
1
X
RS-485 Mode
TABLE 2: RS-232 RX TRUTH TABLE
INPUTS
OUTPUTS
SHDN
RS-485/RS-232
B/R1IN, A/R2IN
R1OUT, RO/R2OUT
X
0
0
1
X
0
1
0
X
0
Inputs open
1
X
1
X
R1OUT High-Z,
RO/R2OUT in RS-485 Mode
19
SP335E
RS-232/RS-485/RS-422 TRANSCEIVER WITH INTERNAL TERMINATION
REV. 1.0.2
TABLE 3: RS-485/422 TX TRUTH TABLE
INPUTS
OUTPUTS
SHDN
RS-485/RS-232
DE/T2IN
DI/T1IN
Z(B)/T1OUT
Y(A)/T2OUT
0
X
X
X
1/8th unit load
1/8th unit load
1
1
0
X
1/8th unit load
1/8th unit load
1
1
1
0
1
0
1
1
1
1
0
1
X
0
X
X
RS-232 Mode
TABLE 4: RS-485/422 RX TRUTH TABLE
INPUTS
OUTPUT
RS-485/RS-232
SHDN
HALF/FULL
RE
(A-B)
(Y-Z)
RO/R2OUT
1
0
X
X
X
X
High-Z
1
1
0
0
-50mV
X
1
1
1
0
0
-200mV
X
0
1
1
0
0
Floating
X
1
1
1
1
0
X
-50mV
1
1
1
1
0
X
-200mV
0
1
1
1
0
X
Floating
1
1
1
X
1
X
X
High-Z
0
X
X
X
X
X
RS-232 Mode
TABLE 5: RS-485/422 TERMINATION TRUTH TABLE
FD_TX_TERM
TERM
RS-485/RS-232
HALF/FULL
TX TERM
RX TERM
PIN 12
PIN 13
PIN 14
PIN 15
PINS 3-4
PINS 18-19
X
0
1
0
-
-
0
1
1
0
-
ON
1
1
1
0
ON
ON
X
0
1
1
-
-
X
1
1
1
ON
-
X
X
0
X
-
-
The DE and RE pins have no effect on the termination setting in any mode.
20
SP335E
REV. 1.0.2
RS-232/RS-485/RS-422 TRANSCEIVER WITH INTERNAL TERMINATION
PACKAGE DRAWINGS
FIGURE 14. QFN32 MECHANICAL DIMENSIONS
Top View
Bottom View
Side View
Drawing No:
Revision:
21
POD-00000037
B
SP335E
RS-232/RS-485/RS-422 TRANSCEIVER WITH INTERNAL TERMINATION
REV. 1.0.2
FIGURE 15. QFN32 RECOMMENDED STENCIL DESIGN AND LAND PATTERN
Drawing No:
Revision:
22
POD-00000037
B
SP335E
RS-232/RS-485/RS-422 TRANSCEIVER WITH INTERNAL TERMINATION
REV. 1.0.2
REVISION HISTORY
DATE
REVISION
DESCRIPTION
Sept 2013
1.0.0
Production Release
August 2017
1.0.1
Update to MaxLinear logo. Updated format and ordering information table. Updated
package drawing to reflect 32 pins on package for bottom and side view.
August 2017
1.0.2
Added maximum operating junction temperature, page 2.
Corporate Headquarters:
High Performance Analog:
5966 La Place Court
48720 Kato Road
Suite 100
Fremont, CA 94538
Carlsbad, CA 92008
Tel.: +1 (510) 668-7000
Tel.:+1 (760) 692-0711
Fax: +1 (510) 668-7001
Fax: +1 (760) 444-8598
Email: serialtechsupport@exar.com
www.maxlinear.com
www.exar.com
The content of this document is furnished for informational use only, is subject to change without notice, and should not be construed as a commitment by MaxLinear, Inc.. MaxLinear,
Inc. assumes no responsibility or liability for any errors or inaccuracies that may appear in the informational content contained in this guide. Complying with all applicable copyright laws
is the responsibility of the user. Without limiting the rights under copyright, no part of this document may be reproduced into, stored in, or introduced into a retrieval system, or transmitted
in any form or by any means (electronic, mechanical, photocopying, recording, or otherwise), or for any purpose, without the express written permission of MaxLinear, Inc.
Maxlinear, Inc. does not recommend the use of any of its products in life support applications where the failure or malfunction of the product can reasonably be expected to cause failure
of the life support system or to significantly affect its safety or effectiveness. Products are not authorized for use in such applications unless MaxLinear, Inc. receives, in writing,
assurances to its satisfaction that: (a) the risk of injury or damage has been minimized; (b) the user assumes all such risks; (c) potential liability of MaxLinear, Inc. is adequately protected
under the circumstances.
MaxLinear, Inc. may have patents, patent applications, trademarks, copyrights, or other intellectual property rights covering subject matter in this document. Except as expressly
provided in any written license agreement from MaxLinear, Inc., the furnishing of this document does not give you any license to these patents, trademarks, copyrights, or other
intellectual property.
Company and product names may be registered trademarks or trademarks of the respective owners with which they are associated.
© 2013-2017 MaxLinear, Inc. All rights reserved
23
工商网监
湘ICP备2023018690号
