SP7662

SP7662 Wide Input Voltage Range 12A, 300kHz, Buck Regulator FEATURES ■ 4.75V to 22V Input Voltage Range using Single Supply ■ 3V to 22V Input Voltage Range using Dual Supply ■ ±% 0.8V Reference ■ 2A Output Capability ■ Current Limiting using Inductor DCR ■ Built in Low RDS(ON) Power Switches ■ 300 kHz Fixed Frequency Operation ■ Over Temperature Protection ■ Short Circuit Protection with Auto-Restart ■ Wide BW Amp Allows Type II or III Compensation ■ Programmable Soft Start ■ Fast Transient Response ■ High Efficiency: Greater than 95% Possible ■ Nonsynchronous Start-Up into a Pre-Charged Output ■ Available in RoHS Compliant, Lead Free Packaging: Small 7mm x 4mm DFN ■ U.S. Patent #6,922,04 LX LX LX 26 25 24 BOTTOM VIEW Heatsink Pad 1 Connect to Lx Power Blox SP7662 TM DFN PACKAGE 7mm x 4mm (Option 2) 1 PGND 2 PGND 3 PGND 4 PGND LX 23 VCC 2 2 UVIN 21 GND 20 GND 19 VIN 18 BST 17 LX 16 LX 15 LX 14 Heatsink Pad 3 Connect to VINP Pin 29 Heatsink Pad 2 Connect to GND Pin 28 Pin 27 5 GND 6 VFB 7 COMP 8 SS 9 GND 10 ISN 11 ISP 12 SWN 13 VINP DESCRIPTION The SP7662 is a synchronous step-down switching regulator optimized for high efficiency. The part is designed for use with a single 4.75V to 22V single supply or 3V to 22V input if an external Vcc is provided. The SP7662 provides a fully integrated buck regulator solution using a fixed 300 kHz frequency, PWM voltage mode architecture. Protection features include UVLO, thermal shutdown, output current limit and short circuit protection. The SP7662 is available in the space saving DFN package. 5 4 3 TYPICAL APPLICATION CIRCUIT 2  VIN 12Vin (9.6V - 16V)  D  VOUT LX 28 27 C3 22uF  C2 22uF C 22uF L, SC508-2R7M 2.7uH, 4. mOhm R3 5.k C4 R9 ISP 3.30V, 0-12A R4 5.k  3 D GND PAD GND CZ2 C 2 SWN PAD  VFB 2 3 4 5 6 PGND PGND PGND PGND GND VFB COMP SS GND ISN ISP LX LX 26 25 24 23 22 2 20 9 8 7 6 5 4 NC 0.uF 6.9k ISN VFB RZ3 453 R 0k C5 C6 00uF 00uF  4 RZ2 4.02k U SP7662 LX LX VCC UVIN GND GND VIN BST LX CZ3 2200pF R2 3.6k 0nF CVCC 4.7uF CP 00pF CSS 47nF GND C 7 8 9 0  CF 00pF VIN PAD C9 6.8nF B 2 3 RBST 5. 22nF CBST SWN VIN LX LX SD0AWS DBST B ISN ISP LX 29 Rs  Ohm Cs 2.2nF LX Rs2  Ohm Cs2 2.2nF Mar -07 Rev AJ A SP7662 Wide Input Voltage Range 2A, 300kHz Buck Regulator © 2007 Sipex Corporation A  ABSOLUTE MAXIMUM RATINGS These are stress ratings only and functional operation of the device at these ratings or any other above those indicated in the operation sections of the specifications below is not implied. Exposure to absolute maximum rating conditions for extended periods of time may affect reliability. VCC ...................................................................................................7V ViN .................................................................................................25V BST................................................................................................ 30V LX-BST ...............................................................................-0.3V to 7V LX ........................................................................................-V to 30V All other pins .......................................................... -0.3V to VCC + 0.3V Storage Temperature ................................................... -65°C to 50°C Power Dissipation ........................................Internally Limited via OTP Lead Temperature (Soldering, 0 sec) .......................................300°C ESD Rating ........................................................................... 2kV HBM Thermal Resistance θJC............................................................ 5°C/W Specifications are for TAMB = TJ = 25°C, and those denoted by ♦ apply over the full operating range, -40°C< Tj< 25°C. Unless otherwise specified: 4.5V < Vcc < 5.5V, 3V < ViN < 22V, BST = LX + 5V, UVIN = 3V, CVCC = µF, CCOMP = 0.µF, Css = 50nF. ELECTRICAL SPECIFICATIONS CONDITIONS PARAMETER QUIESCENT CURRENT ViN Supply Current (No switching) ViN Supply Current (switching) BST Supply Current (No switching) BST Supply Current (switching) PROTECTION: UVLO MIN TYP .5 8 0.2 3 MAX UNITS ♦ 3.0 20 0.4 6 mA mA ♦ VfB= 0.9V mA mA ♦ VfB= 0.9V Vcc UVLO Start Threshold 4.00 Vcc UVLO Hysteresis UVIN Start Threshold UVIN Hysteresis UVIN Input Current 00 2.30 200 4.25 200 2.50 300 4.50 300 2.65 400 .0 V mV V ♦ ♦ ♦ ♦ ♦ UVIN=3.0V 2X Gain Config., Measure VfB; Vcc=5V mV µA ERROR AMPLIFIER REFERENCE Error Amplifier Reference 0.792 0.800 0.808 0.784 0.800 0.86 70 -230 50 -50 50 3.2 3.5 -2.0 230 -70 200 3.8 V V Error Amplifier Reference Over Line COMP Sink Current COMP Source Current VfB Input Bias Current COMP Clamp COMP Clamp Temp. Coefficient VCC LINEAR REGULATOR ♦ ♦ VfB=0.9V, COMP=0.9V ♦ VfB=0.9V, COMP=0.9V ♦ VfB=0.8V VfB=0.7V, TA=25°C µA µA nA V mV/°C VCC Output Voltage 4.7 4.5 250 5.0 4.73 500 5.3 V ♦ Dropout Voltage 750 mV ViN = 6 to 23V, ILOAD = 0mA to 30mA ♦ ViN = 5V, 20mA Vin-Vout = Dropout voltage when ♦ Vcc regulated drops by 2%. IVCC = 30mA. © 2007 Sipex Corporation Mar -07 Rev AJ SP7662 Wide Input Voltage Range 2A, 300kHz Buck Regulator 2 Specifications are for TAMB = TJ = 25°C, and those denoted by ♦ apply over the full operating range, -40°C< Tj< 25°C. Unless otherwise specified: 4.5V < Vcc < 5.5V, 3V < ViN < 22V, BST = LX + 5V, UVIN = 3V, CVCC = µF, CCOMP = 0.µF, Css = 50nF. ELECTRICAL SPECIFICATIONS PARAMETER Ramp Amplitude RAMP Offset Ramp offset Temperature Coefficient GH Minimum Pulse Width Maximum Controllable Duty Ratio Maximum Duty Ratio Internal Oscillator Ratio TIMERS: SOFTSTART SS Charge Current: SS Discharge Current: Short Circuit Threshold Voltage MIN TYP MAX UNITS ♦ 0.80 .7 .00 2.0 -2 50 92 00 255 -6 .0 300 -0 2.0 345 -4.0 3.0 97 80 .20 2.3 V V mV/°C ns % % kHZ CONDITIONS CONTROL LOOP: PWM COMPARATOR, RAMP & LOOP DELAY PATH ♦ ♦ ♦ ♦ ♦ ♦ ♦ ♦ Fault Present, SS=0.2V Valid for 20 cycles µA mA PROTECTION: SHORT CIRCUIT, OVERCURRENT & THERMAL 0.20 0.25 220 60 0.30 270 V ms mV ♦ ♦ VfB=0.5V Measured ISP - ISN 70 Hiccup Timeout Overcurrent Threshold 54 Voltage ISP, ISN Common Mode 0 Range Thermal Shutdown 35 Temperature Thermal Recovery Temperature Thermal Hysteresis OUTPUT: POWER STAGE 66 3.6 V °C °C °C Guaranteed by design 45 35 0 55 High Side Switch RDSON Synchronous Low Side Switch RDSON Maximum Output Current 2 6.8 6.8 20.5 8.5 mΩ mΩ A VGS=4.5V; IDrAiN=5A; TAMB=25°C VGS=4.5V; IDrAiN=5A; TAMB=25°C ♦ Mar -07 Rev AJ SP7662 Wide Input Voltage Range 2A, 300kHz Buck Regulator © 2007 Sipex Corporation 3 CONTROLLER BLOCK DIAGRAM VC C C O MP SS V FB IN T 1.6 V A S Y N C . S TA R TU P C O MP A R A TO R G L H OL D O FF BS T V FB VCC 10 uA S O FTS TA R T I N P U T SS 0.1V P W M LO O P VC C G m E R R O R A MP LIFIE R FA U L T RE S E T D O MIN A N T R Q P OS R E F F A U LT S QP W M GH V PO S Gm S Y N C H R O NO U S DR I V E R S WN GL FA U L T 300 kH Z P GN D C LK C L OC K P U LS E G E N E R A TO R 2.8 V 1. 3 V F A U LT R A MP = 1 V V CC R E FE R E N C E C OR E 0. 8V R E F OK PO W E R F A U LT 4.25 V O N 4.05 V OFF 145ºC O N 135ºC O FF V C C U V LO TH E R MA L S H U TD OW N SET D O MIN A N T S Q H I C C U P F A U LT 0. 25V V P OS 5V L IN E A R R E G U LA TO R V F B IN T S H O R T C IR C U IT D E TE C TIO N R GND 200ms D elay OV E R C U R R E N T D E TE C TIO N C OU N TE R C LK V IN 60 mV R E F OK C LR 140K U V IN 2.50 V O N 2.20 V O FF 50K V I N U V LO IS P IS N T HE R M A L A ND O V E R C UR R E N T P R O T E C T I O N UV LO C O M P A R A T O R S Note: The SP7662 uses the Sipex PWM controller SP6133. Mar -07 Rev AJ SP7662 Wide Input Voltage Range 2A, 300kHz Buck Regulator © 2007 Sipex Corporation 4 PIN DESCRIPTION SP7662 DFN PACKAGE 7mm x 4mm (Option 2) LX 26 LX 25 LX 24 LX 23 VCC 22 UVIN 21 GND 20 GND 19 VIN 18 BST 17 LX 16 LX 15 LX 14 Heatsink Pad 3 Connect to VINP Pin 29 Heatsink Pad 2 Connect to GND Pin 28 Pin 27 1 PGND 2 PGND 3 PGND 4 PGND 5 GND 6 VFB 7 COMP 8 SS 9 GND 10 ISN 11 ISP 12 SWN 13 VINP BOTTOM VIEW Heatsink Pad 1 Connect to Lx Pin Pin # Name Description -4 PGND Ground connection for the synchronous rectifier. Ground Pin. The control circuitry of the IC and lower power driver are referenced to this 5, 9, GND 9, 20 pin. Return separately from other ground traces to the (-) terminal of COut. Feedback Voltage and Short Circuit Detection pin. It is the inverting input of the Error Amplifier and serves as the output voltage feedback point for the Buck Converter. The output voltage is sensed and can be adjusted through an external resistor divider. Whenever VFB drops 0.25V below the positive reference, a short circuit fault is detected and the IC enters hiccup mode. 6 VFB 7 8 0  2 3 4-6, 23-26 Output of the Error Amplifier. It is internally connected to the inverting input of the COMP PWM comparator. An optimal filter combination is chosen and connected to this pin and either ground or VFB to stabilize the voltage mode loop. Soft Start. Connect an external capacitor between SS and GND to set the soft start SS rate based on the 0µA source current. The SS pin is held low via a mA (min) current during all fault conditions. ISN Current sense negative input. Rail-to-rail input for overcurrent detection. ISP SWN VINP LX BST VIN UVIN VCC Current sense positive input. Rail-to-rail input for overcurrent detection. Lower supply rail for the GH high-side gate driver. Connect this pin to the switching node as close as possible to pins 23- 27. Do not connect this pin to pins 4 – 6. Input connection to the high side N-channel MOSFET. Connect an inductor between this pin and VOut. High side driver supply pin. Connect BST to the external boost diode and capacitor as shown in the Typical Application Circuit on page . The high side driver is connected between BST pin and SWN pin. ViN connection for internal LDO and PWM Controller. UVLO input for ViN voltage. Connect a resistor divider between ViN and UVIN to set minimum operating voltage. Use resistor values below 20kΩ to override internal resistor divider. Output of internal regulator. May be exterinally biased if Vin < 5V. SP7662 Wide Input Voltage Range 2A, 300kHz Buck Regulator © 2007 Sipex Corporation 7 8 2 22 Mar -07 Rev AJ 5 THEORY OF OPERATION General Overview The SP7662 is a fixed frequency, voltage mode, synchronous PWM regulator optimized for high efficiency. The part has been specifically designed for single supply operation from a 5V to 22V input. The heart of the SP7662 is a wide bandwidth transconductance amplifier designed to accommodate Type II and Type III compensation schemes. A precision 0.8V reference, present on the positive terminal of the error amplifier, permits the programming of the output voltage down to 0.8V via the VFB pin. The output of the error amplifier, COMP, is compared to a .V peak-to-peak ramp, which is responsible for trailing edge PWM control. This voltage ramp and PWM control logic are governed by the internal oscillator that accurately sets the PWM frequency to 300kHz. The SP7662 contains two unique control features that are very powerful in distributed applications. First, nonsynchronous driver control is enabled during startup, to prohibit the low side switch from pulling down the output until the high side switch has attempted to turn on. Second, a 00% duty cycle timeout ensures that the low side switch is periodically enhanced during extended periods at 00% duty cycle. This guarantees the synchronized refreshing of the BST capacitor during very large duty ratios. The SP7662 also contains a number of valuable protection features. Programmable VIN UVLO allows the user to set the exact value at which the conversion voltage can safely begin down-conversion, and an internal VCC UVLO which ensures that the controller itself has enough voltage to properly operate. Other protection features include thermal shutdown and short-circuit detection. In the event that either a thermal, short-circuit, or UVLO fault is detected, the SP7662 is forced into an idle state where the output drivers are held off for a finite period before a restart is attempted. Mar -07 Rev AJ Soft Start “Soft Start” is achieved when a power converter ramps up the output voltage while controlling the magnitude of the input supply source current. In a modern step down converter, ramping up the positive terminal of the error amplifier controls soft start. As a result, excess source current can be defined as the current required to charge the output capacitor. IViN = COut • (∆VOut / ∆TSOft-StArt) The SP7662 provides the user with the option to program the soft start rate by tying a capacitor from the SS pin to GND. The selection of this capacitor is based on the 0µA pull up current present at the SS pin and the 0.8V reference voltage. Therefore, the excess source can be redefined as: IViN = COut • [∆VOut •0µA / (CSS • 0.8V)] Under Voltage Lock Out (UVLO) The SP7662 has two separate UVLO comparators to monitor the bias (Vcc) and Input (ViN) voltages independently. The Vcc UVLO is internally set to 4.25V. The ViN UVLO is programmable through UViN pin. When UVIN pin is greater than 2.5V the SP7662 is permitted to start up pending the removal of all other faults. A pair of internal resistors is connected to UVIN as shown in the figure below. SP7662 VIN R6 UVIN 140KΩ R7 GND 2.5V ON 2.2V OFF 50KΩ + Internal and external bias of UVIN SP7662 Wide Input Voltage Range 2A, 300kHz Buck Regulator © 2007 Sipex Corporation 6 THEORY OF OPERATION Therefore without external biasing the ViN start threshold is 9.5V. A small capacitor may be required between UVIN and GND to filter out noise. For applications with ViN of 5V or 3.3V, connect UVIN directly to ViN. To program the ViN start threshold, use a pair of external resistors as shown. If external resistors are an order of magnitude smaller than internal resistors, then the ViN start threshold is given by: ViN(start) = 2.5 • (R6+R7)/R7 For example, if it is required to have a ViN start threshold of 7V, then let R7 = 5KΩ and using the ViN start threshold equation we get R6 = 9.09KΩ. Thermal and Short-Circuit Protection Because the SP7662 is designed to drive large output current, there is a chance that the power converter will become too hot. Therefore, an internal thermal shutdown (45°C) has been included to prevent the IC from malfunctioning at extreme temperatures. A short-circuit detection comparator has also been included in the SP7662 to protect against an accidental short at the output of the power converter. This comparator constantly monitors the positive and negative terminals of the error amplifier, and if the VfB pin falls more than 250mV (typical) below the positive reference, a short-circuit fault is set. Because the SS pin overrides the internal 0.8V reference during soft start, the SP7662 is capable of detecting short-circuit faults throughout the duration of soft start as well as in regular operation. Over-Current Protection The Over-current protection feature can only be used on output voltages ≤ 3.3 volts. It is limited by the common mode rating of the op-amp used to sense the voltage across the inductor. Over-current is deMar -07 Rev AJ tected by monitoring a differential voltage across the output inductor as shown in the next figure. SP7662 SWN L = 2.7uH, DCR = 4.1mΩ VOUT R3 5.11KΩ R4 5.11KΩ ISP ISN CSP 6.8nF CS 0.uF Over-current detection circuit Inputs to an over-current detection comparator, set to trigger at 60 mV nominal, are connected to the inductor as shown. Since the average voltage sensed by the comparator is equal to the product of inductor current and inductor DC resistance (DCR), then IMAx = 60mV / DCR. Solving this equation for the specific inductor in circuit 1, IMAx = 4.6A. When IMAx is reached, a 220 ms time-out is initiated, during which top and bottom drivers are turned off. Following the time-out, a restart is attempted. If the fault condition persists, then the time-out is repeated (referred to as hiccup). Increasing the Current Limit If it is desired to set IMAx > {60mV / DCR} (in this case larger than 4.6A), then a resistor R9 should be added as shown in the next figure. R9 forms a resistor divider and reduces the voltage seen by the comparator. (IMAx • DCR) Since: 60mV = R9 {R3 + R4 + R9} SP7662 Wide Input Voltage Range 2A, 300kHz Buck Regulator © 2007 Sipex Corporation 7 THEORY OF OPERATION Solving for R9 we get: R9 = [60mV • (R3 + R4)] [(IMAx • DCR) – 60mV] As an example: if desired IMAx is 7A, then R9 = 63.4KΩ. R8 = R4 • [VOut - 60mV + (IMAX • DCR)] 60mV - (IMAX • DCR) As an example: for IMAx of 2A and VOut of 3.3V, calculated R8 is 1.5MΩ. SP7662 SWN L = 2.7uH, DCR = 4.1mΩ SP7662 VOUT SWN L = 2.7uH, DCR = 4.1mΩ VOUT R3 5.11KΩ R9 63.4KΩ R4 5.11KΩ R3 5.11KΩ R4 5.11KΩ ISP ISN CSP 6.8nF ISP ISN CS 0.uF CSP 6.8nF CS 0.uF R8 1.5MΩ Over-current detection circuit for Imax > 60mV / DCR Decreasing the Current Limit If it is required to set IMAx < {60mV / DCR, a resistor is added as shown in the following figure. R8 increases the net voltage detected by the current-sense comparator. Voltage at the positive and negative terminal of comparator is given by: VSP = VOut + (IMAx • DCR) VSN = VOut • {R8 / (R4 +R8)} Since the comparator is triggered at 60mV: VSP-VSN = 60 mV Combining the above equations and solving for R8: Over-current detection circuit for Imax < {60mV / DCR} Handling of Faults Upon the detection of power (UVLO), thermal, or short-circuit faults, the SP7662 is forced into an idle state where the SS and COMP pins are pulled low and both switches are held off. In the event of UVLO fault, the SP7662 remains in this idle state until the UVLO fault is removed. Upon the detection of a thermal or short-circuit fault, an internal 200ms timer is activated. In the event of a short-circuit fault, a restart is attempted immediately after the 200ms timeout expires. Whereas, when a thermal fault is detected the 200ms delay continuously recycles and a restart cannot be attempted until the thermal fault is removed and the timer expires. Mar -07 Rev AJ SP7662 Wide Input Voltage Range 2A, 300kHz Buck Regulator © 2007 Sipex Corporation 8 APPLICATIONS INFORMATION Error Amplifier and Voltage Loop The heart of the SP7662 voltage error loop is a high performance, wide bandwidth transconductance a mplifier. Because of the amplifier’s current limited (+/-150µA) transconductance, there are many ways to compensate the voltage loop or to control the COMP pin externally. If a simple, single-pole, single-zero response is desired, then compensation can be as simple as an RC circuit to Ground. If a more complex compensation is required, then the amplifier has enough bandwidth (45° at 4 MHz), and enough gain (60dB) to run Type III compensation schemes with adequate gain and phase margins at crossover frequencies greater than 50kHz. The common mode output of the error amplifier is 0.9V to 2.2V. Therefore, the PWM voltage ramp has been set between .V and 2.2V to ensure proper 0% to 00% duty cycle capability. The voltage loop also includes two other very important features. One is a nonsynchronous startup mode. Basically, the synchronous rectifier cannot turn on unless the high side switch has attempted to turn on or the SS pin has exceeded .7V. This feature prevents the controller from “dragging down” the output voltage during startup or in fault modes. VBST GH Voltage VSWN V(VCC) GL Voltage 0V V(VIN) SWN Voltage -0V -V(Diode) V V(VIN)+V(VCC) BST Voltage V(VCC) TIME Mar -07 Rev AJ The second feature is a 00% duty cycle timeout that ensures synchronized refreshing of the BST capacitor at very high duty ratios. In the event that the high side NFET is on for 20 continuous clock cycles, a reset is given to the PWM flip flop half way through the 2st cycle. This forces GL to rise for the cycle, in turn refreshing the BST capacitor. The boost capacitor is used to generate a high voltage drive supply for the high side switch, which is Vcc above ViN. Power MOSFETs The SP7662 contains a pair of integrated low resistance N-channel switches designed to drive up to 2A of output current. Care should be taken to de-rate the output current based on the thermal conditions in the system such as ambient temperature, airflow and heat sinking. Maximum output current could be limited by thermal limitations of a particular application by taking advantage of the integrated-over-temperature protective scheme employed in the SP7662. The SP7662 incorporates a built-in overtemperature protection to prevent internal overheating. Setting Output Voltages The SP7662 can be set to different output voltages. The relationship in the following formula is based on a voltage divider from the output to the feedback pin VfB, which is set to an internal reference voltage of 0.80V. Standard 1% metal film resistors of surface mount size 0603 are recommended. VOut = 0.80V [R / R2 +  ] => R2 = R / [ ( VOut / 0.80V ) –  ] Where R1 = 10KΩ and for VOut = 0.80V setting, simply remove R2 from the board. Furthermore, one could select the value of the R and R2 combination to meet the exact output voltage setting by restricting the R resistance range such that 10KΩ < R1 < 100KΩ for overall system loop stability. © 2007 Sipex Corporation SP7662 Wide Input Voltage Range 2A, 300kHz Buck Regulator 9 APPLICATIONS INFORMATION Inductor Selection There are many factors to consider in selecting the inductor including core material, inductance vs. frequency, current handling capability, efficiency, size and EMI. In a typical SP7662 circuit, the inductor is chosen primarily for value, saturation current and DC resistance. Increasing the inductor value will decrease output voltage ripple, but degrade transient response. Low inductor values provide the smallest size, but cause large ripple currents, poor efficiency and require more output capacitance to smooth out the larger ripple current. The inductor must be able to handle the peak current at the switching frequency without saturating, and the copper resistance in the winding should be kept as low as possible to minimize resistive power loss. A good compromise between size, loss and cost is to set the inductor ripple current to be within 20% to 40% of the maximum output current. The switching frequency and the inductor operating point determine the inductor value as follows: L = . and provide low core loss at the high switching frequency. Low cost powderediron cores have a gradual saturation characteristic but can introduce considerable AC core loss, especially when the inductor value is relatively low and the ripple current is high. Ferrite materials, although more expensive, have an abrupt saturation characteristic with the inductance dropping sharply when the peak design current is exceeded. Nevertheless, they are preferred at high switching frequencies because they present very low core loss while the designer is only required to prevent saturation. In general, ferrite or molypermalloy materials are a better choice for all but the most cost sensitive applications. Optimizing Efficiency The power dissipated in the inductor is equal to the sum of the core and copper losses. To minimize copper losses, the winding resistance needs to be minimized, but this usually comes at the expense of a larger inductor. Core losses have a more significant contribution at low output current where the copper losses are at a minimum, and can typically be neglected at higher output currents where the copper losses dominate. Core loss information is usually available from the magnetics vendor. Proper inductor selection can affect the resulting power supply efficiency by more than 15%! The copper loss in the inductor can be calculated using the following equation: PL(Cu) = I L(rMS) • rwiNDiNg where IL(rMS) is the RMS inductor current that can be calculated as follows: IL(rMS) = IOut(MAx) • 2 ViN(MAx) • ƒs • Kr • IOut(MAx) VOut • (ViN(MAx) - VOut) where: ƒs = switching frequency Kr = ratio of the AC inductor ripple current to the maximum output current The peak-to-peak inductor ripple current is: IPP = . VOut • (ViN(MAx) - VOut) ViN(MAx) • ƒs •L Once the required inductor value is selected, the proper selection of core material is based on peak inductor current and efficiency requirements. The core must be large enough not to saturate at the peak inductor current IPeAk = IOut(MAx) IPP + 2 √ ( ) + 3 . IOut(MAx) IPP 2 Mar -07 Rev AJ SP7662 Wide Input Voltage Range 2A, 300kHz Buck Regulator © 2007 Sipex Corporation 0 APPLICATIONS INFORMATION Output Capacitor Selection The required ESR (Equivalent Series Resistance) and capacitance drive the selection of the type and quantity of the output capacitors. The ESR must be small enough that both the resistive voltage deviation due to a step change in the load current and the output ripple voltage do not exceed the tolerance limits expected on the output voltage. During an output load transient, the output capacitor must supply all the additional current demanded by the load until the SP7662 adjusts the inductor current to the new value. In order to maintain VOut,the capacitance must be large enough so that the output voltage is held up while the inductor current ramps to the value corresponding to the new load current. Additionally, the ESR in the output capacitor causes a step in the output voltage equal to the current. Because of the fast transient response and inherent 00% to 0% duty cycle capability provided by the SP7662 when exposed to output load transients, the output capacitor is typically chosen for ESR, not for capacitance value. The ESR of the output capacitor, combined with the inductor ripple current, is typically the main contributor to output voltage ripple. The maximum allowable ESR required to maintain a specified output voltage ripple can be calculated by: ReSr ≤ ∆VOut IPk-Pk ∆VOut = ƒs = Switching Frequency D = Duty Cycle COut = Output Capacitance Value Input Capacitor Selection √ ( IPP • ( – D) ƒs • COut ) 2 + (IPP •ReSr) 2 The input capacitor should be selected for ripple current rating, capacitance and voltage rating. The input capacitor must meet the ripple current requirement imposed by the switching current. In continuous conduction mode, the source current of the high-side MOSFET is approximately a square wave of duty cycle VOut/ViN. More accurately, the current wave form is trapezoidal, given a finite turn-on and turn-off, switch transition slope. Most of this current is supplied by the input bypass capacitors. The RMS current handling capability of the input capacitors is determined at maximum output current and under the assumption that the peak-to-peak inductor ripple current is low, it is given by: ICiN(rMS) = IOut(MAx) • √D(1 - D) The worst case occurs when the duty cycle D is 50% and gives an RMS current value equal to IOUT/2. Select input capacitors with adequate ripple current rating to ensure reliable operation. The power dissipated in the input capacitor is: PCiN = I CiN(rMS) • reSr(CiN) This can become a significant part of power losses in a converter and hurt the overall energy transfer efficiency. The input voltage ripple primarily depends on the input 2 where: ∆VOut = Peak-to-Peak Output Voltage Ripple IPk-Pk = Peak-to-Peak Inductor Ripple Current The total output ripple is a combination of the ESR and the output capacitance value and can be calculated as follows: Mar -07 Rev AJ SP7662 Wide Input Voltage Range 2A, 300kHz Buck Regulator © 2007 Sipex Corporation  APPLICATIONS INFORMATION capacitor ESR and capacitance. Ignoring the inductor ripple current, the input voltage ripple can be determined by: ∆ViN = Loop Compensation Design The open loop gain of the whole system can be divided into the gain of the error amplifier, PWM modulator, buck converter output stage, and feedback resistor divider. In order to cross over at the desired frequency cut-off (FCO), the gain of the error amplifier must compensate for the attenuation caused by the rest of the loop at this frequency. The goal of loop compensation is to manipulate loop frequency response such that its crossover gain at 0db, results in a slope of -20db/decade. The first step of compensation design is to pick the loop crossover frequency. High crossover frequency is desirable for fast transient response, but often jeopardizes the power supply stability. Crossover frequency should be higher than the ESR zero but less than /5 of the switching frequency or IOut(MAx)•reSr(CiN) + IOut(MAx)•VOut•(ViN - VOut) V2iN • ƒs • CiN The capacitor type suitable for the output capacitors can also be used for the input capacitors. However, exercise extra caution when tantalum capacitors are used. Tantalum capacitors are known for catastrophic failure when exposed to surge current, and input capacitors are prone to such surge current when power supplies are connected “live” to low impedance power sources. Although tantalum capacitors have been successfully employed at the input, it is generally not recommended. Type III Voltage Loop Compensation GAMP (s) Gain Block VREF (Volts) (SRz2Cz2+1)(SR1Cz3+1) SR1Cz2(SRz3Cz3+1)(SRz2Cp1+1) Notes: RESR = Output Capacitor Equivalent Series Resistance. RDC = Output Inductor DC Resistance. VRAMP_PP = SP7662 Internal Ramp Amplitude Peak-to-Peak Voltage. Condition: Cz2 >> Cp1 & R1 >> Rz3 Output Load Resistance >> RESR & RDC PWM Stage GPWM Gain Block VIN VRAMP_PP Output Stage GOUT (s) Gain Block (SRESRCOUT+ 1) [S^2LCOUT+S(RESR+RDC) COUT+1] VOUT (Volts) Voltage Feedback GFBK Gain Block R2 VFBK (Volts) (R1 + R2) or VREF VOUT SP7662 Voltage Mode Control Loop with Loop Dynamic Mar -07 Rev AJ SP7662 Wide Input Voltage Range 2A, 300kHz Buck Regulator © 2007 Sipex Corporation 2 APPLICATIONS INFORMATION 60kHz. The ESR zero is contributed by the ESR associated with the output capacitors and can be determined by: ƒP(LC) = .  2π • √ L • COut ƒZ(ESR) =  2π • COut • ReSr The next step is to calculate the complex conjugate poles contributed by the LC output filter, Gain (dB) When the output capacitors are of a Ceramic Type, the SP7662 Evaluation Board requires a Type III compensation circuit to give a phase boost of 80° in order to counteract the effects of an underdamped resonance of the output filter at the double pole frequency. Condition: C22 >> CP1, R1 >> RZ3 Error Amplifier Gain Bandwidth Product 20 Log (RZ2/R1) 1/6.28 (RZ2) (CP1) 1/6.28 (RZ3) (CZ3) 1/6.28 (R1) (CZ3) 1/6.28(R22) (CZ2) 1/6.28 (R1) (CZ2) Frequency (Hz) Bode Plot of Type III Error Amplifier Compensation. CP1 RZ3 CZ3 CZ2 VFB RSET RZ2 VOUT R1 68.1kΩ, 1% + + - 0.8V COMP CF1 RSET = 54.48 (kΩ) (VOUT -0.8) Type III Error Amplifier Compensation Circuit Mar -07 Rev AJ SP7662 Wide Input Voltage Range 2A, 300kHz Buck Regulator © 2007 Sipex Corporation 3 APPLICATIONS INFORMATION VOUT 3.30V, 0-12A LX 2.7uH, 4.1 mΩ R3 5.11KΩ D1 NP C4 R9 ISP R4 5.11KΩ 0.1uF 60kΩ ISN 28 27 R11 10Ω,1% C5 100uF RZ3 499Ω,1% R1 10kΩ,1% C6 100uF C7 NP 1 2 SWN PAD GND PAD PGND PGND PGND PGND GND VFB COMP SS GND ISN ISP SWN VINP LX LX 26 25 24 23 22 21 20 19 18 17 16 15 14 CZ2 22nF CP1 RZ2 2KΩ,1% 100pF 3 4 5 6 7 U1 SP7662 LX LX VCC UVIN GND GND VIN BST LX LX LX CVCC 4.7uF R12 0 Ohms GND CZ3 2200pF R7 NP C8 NP CF1 100pF CSS 47nF 8 9 R2 3.2kΩ,1% R6 NP R8 NP 10 11 RBST C9 6.8nF 12 13 0 Ohms 22nF CBST SD101AWS DBST ISN ISP LX 29 VIN PAD Rs1 1Ω Cs1 2.2nF Rs2 1Ω Cs2 2.2nF VIN 5-22Vin C3 22uF C2 22uF C1 22uF GND Evaluation Board Schematic Parts shown for 5V-22V input, 3.3V Output Mar -07 Rev AJ SP7662 Wide Input Voltage Range 2A, 300kHz Buck Regulator © 2007 Sipex Corporation 4 TYPICAL PERFORMANCE CHARACTERISTICS 00 95 90 Efficiency (%) Efficiency vs Load at 22Vin 00 95 90 Efficiency (%) Efficiency vs. Load at 12VIN 85 80 75 70 65 60 55 50 0 2 4 6 8 0 2 Vout=5.0V Vout=2.5V Vout=.5V Vout=3.3V Vout=.8V Vout=.2V 85 80 75 70 65 60 55 50 0 2 4 6 8 0 2 Vout=5.0V Vout=3.3V Vout=2.5V Vout=.8V Vout=.5V Vout=.2V Vout=0.8V Output Load (A) Output Load (A) 00 Efficiency vs Load at 3.3Vin 00 Efficiency vs Load at 5.0Vin 90 Efficiency (%) Efficiency (%) 90 80 Vout=2.5V 80 Vout=3.3V 70 Vout=1 .8V Vout=1 .5V 70 Vout=2.5V Vout=1 .8V Vout=1 .5V Vout=1 .2V Vout=0.8V 60 Vout=1 .2V Vout=0.8V 60 50 0 2 4 6 8 0 2 50 0 2 4 6 8 0 2 Output Load (A) Output Load (A) Mar -07 Rev AJ SP7662 Wide Input Voltage Range 2A, 300kHz Buck Regulator © 2007 Sipex Corporation 5 TYPICAL PERFORMANCE CHARACTERISTICS Vout Ripple Vout Ripple Output Ripple, No Load Output Ripple, Iout=12A Vin Vout Vin Vout Soft start Soft start Iout 5A/div Iout 5A/div Start up Response, Iout=6A Start up Response, No Load Vin Vout Soft start Vout Transient Iout 10A/di Start up response, Iout=12A Mar -07 Rev AJ Iout 5A/div Load Step Response, Iout=6A -12A © 2007 Sipex Corporation SP7662 Wide Input Voltage Range 2A, 300kHz Buck Regulator 6 TYPICAL PERFORMANCE CHARACTERISTICS Vout Transient Vout Soft start Iout 5A/div Iout 0A/div Load Step Response, Iout=0A -2A Output Short Circuit Vout Vin SoftStart Vout (V) 3.38 3.36 3.34 Vout vs Load at 12Vin Iout 5A/div Vout=3.3V 3.32 0 2 4 6 8 0 2 Output Load (A) OCP Hiccup Response Mar -07 Rev AJ SP7662 Wide Input Voltage Range 2A, 300kHz Buck Regulator © 2007 Sipex Corporation 7 PACKAGE: 26 PIN DFN Mar -07 Rev AJ SP7662 Wide Input Voltage Range 2A, 300kHz Buck Regulator © 2007 Sipex Corporation 8 ORDERING INFORMATION Part Number Junction Temperature Package SP7662ER/TR..................................-40°C to +25°C............ .................................26 Pin 7 X 4 DFN (Option 2) SP7662ER-L/TR.............................-40°C to +25°C..........................(Lead Free) 26 Pin 7 X 4 DFN (Option 2) /TR = Tape and Reel Pack quantity is 3,000 26 pin DFN. Sipex Corporation Headquarters and Sales Office 233 South Hillview Drive Milpitas, CA 95035 TEL: (408) 934-7500 FAX: (408) 935-7600 Sipex Corporation reserves the right to make changes to any products described herein. Sipex does not assume any liability arising out of the application or use of any product or circuit described herein; neither does it convey any license under its patent rights nor the rights of others. Mar -07 Rev AJ SP7662 Wide Input Voltage Range 2A, 300kHz Buck Regulator © 2007 Sipex Corporation 9