SPX1117HM3-L-2-85

SPX1117 800mA Low Dropout Voltage Regulator FEATURES ■ Guaranteed 0.8A Output Current ■ Guaranteed 1A Peak Current ■ Three Terminal Adjustable or Fixed 1.5V, 1.8V, 2.5V, 2.85V, 3.0V, 3.3V and 5V ■ Low Quiescent Current ■ Low Dropout Voltage of 1.1V at 0.8A ■ 0.1% Line and 0.2% Load Regulation ■ Stable with 2.2uF Ceramic Capacitor ■ Overcurrent and Thermal Protection ■ Lead Free, RoHS Compliant Packages: SOT-223,TO-252, TO-220, and TO-263 DESCRIPTION The SPX1117 is a low power positive-voltage regulator designed to satisfy moderate power requirements with a cost effective, small footprint solution. This device is an excellent choice for use in battery-powered applications and portable computers. The SPX1117 features very low quiescent current and a low dropout voltage of 1.1V at a full load. As output current decreases, quiescent current flows into the load, increasing efficiency. SPX1117 is available in adjustable or fixed 1.5V, 1.8V, 2.5V,2.5V, 2.85V, 3.0V, 3.3V and 5V output voltages. The SPX1117 is offered in several 3-pin surface mount packages: SOT-223, TO-252, TO-220 and TO-263. An output capacitor of 10µF provides unconditional stability while a smaller 2.2µF capacitor is sufficient for most applications. FUNCTIONAL DIAGRAM VIN APPLICATIONS ■ Desktop PC's Servers ■ SCSI-II Active Terminator ■ Portable/ Palm Top / Notebook Computers ■ Cordless Phones ■ Battery Chargers ■ Disk Drives ■ Portable Consumer Equipment ■ Portable Instrumentation ■ SMPS Post-Regulator Current Limit + VOUT ICL AMP + 1.25V Thermal Limit + – I TL VREF ADJ/GND IADJ ~ 50µA – Apr 20-07 Rev B SPX1117 800mA Low Dropout Voltage Regulator © 2007 Sipex Corporation 1 ABSOLUTE MAXIMUM RATINGS Power Dissipation.......................................Internally Limited Lead Temperature (soldering, 5 seconds) ...............260°C Storage Temperature Range.......................-65°C to +150°C Operating Junction Temperature Range.....-40°C to +125°C Input Supply Voltage .................................................... +20V Input to Output Voltage ................................................ 18.8V ESD Rating.................................................................2kV min These are sterss ratings only and functional operation of the device at these ratings or any other above those indicated in the operation sections of the specifications below is not implied. Exposure to absolute maximum rating conditions for extended periods of time may affect reliability. ELECTRICAL CHARACTERISTICS TA = 25°C, CIN = COUT = 10µF, unless otherwise specified. The Boldface applies over the full operating temperature range. PARAMETER 1.5V Version Output Voltage 1.8V Version Output Voltage 2.5V Version Output Voltage 2.85V Version Output Voltage 3.00V Version Output Voltage 3.30V Version Output Voltage 5V Version Output Voltage All Voltage Options Reference Voltage Output Voltage Temperature Stability Line Regulation (Note 1) Load Regulation (Note 1) Dropout Voltage (Note 2) Quiescent Current VINMIN ≤VIN≤ 12V,VOUT=Fixed/Adj, IOUT=5mA 5mA≤IOUT≤ 800mA,VOUT=Fixed/Adj IOUT=100mA IOUT=500mA IOUT=800mA 4.25V≤VIN≤ 6.5V SPX1117 800mA Low Dropout Voltage Regulator CONDITIONS MIN TYP MAX UNITS IOUT = 5mA, VIN =3.0V, TJ = 25ºC 5mA ≤ IOUT ≤ 800mA, 2.9V ≤ VIN ≤ 10V IOUT = 5mA, VIN =3.3V, TJ = 25ºC 5mA ≤ IOUT ≤ 800mA, 3.2V ≤ VIN ≤ 10V IOUT = 5mA, VIN =4.0V, TJ = 25ºC 5mA ≤ IOUT ≤ 800mA, 3.9V ≤ VIN ≤ 10V IOUT = 5mA, VIN =4.35V, TJ = 25ºC 5mA ≤ IOUT ≤ 800mA, 4.25V ≤ VIN ≤ 10V IOUT = 5mA, VIN =4.5V, TJ = 25ºC 5mA ≤ IOUT ≤ 800mA, 4.4V ≤ VIN ≤ 10V IOUT = 5mA, VIN =4.8V, TJ = 25ºC 5mA ≤ IOUT ≤ 800mA, 4.7V ≤ VIN ≤ 10V IOUT = 5mA, VIN =6.5V 5mA ≤ IOUT ≤ 800mA, 6.4V ≤ VIN ≤ 12V IOUT=5mA, (VIN - VOUT )= 2V, TJ = 25ºC 5mA≤IOUT≤ 800mA, 1.4V≤(VIN-VOUT)≤ 10V 1.485 1.470 1.500 1.515 1.530 V 1.782 1.764 1.800 1.818 1.836 V 2.475 2.450 2.500 2.525 2.550 V 2.821 2.793 2.850 2.878 2.907 V 2.970 2.940 3.000 3.030 3.060 V 3.267 3.234 3.300 3.333 3.366 V 4.950 4.90 5 5.050 5.10 V 1.238 1.225 1.250 0.3 1.262 1.270 V % 3 6 1.00 1.05 1.10 5 7 12 1.20 1.25 1.30 10 mV mV V mA Apr 20-07 Rev B © 2007 Sipex Corporation 2 ELECTRICAL CHARACTERISTICS TA = 25°C, CIN = COUT = 10µF, unless otherwise specified. The Boldface applies over the full operating temperature range. PARAMETER Adjust Pin Current Current Limit Thermal Regulation Ripple Rejection Long Term Stability RMS Output Noise CONDITIONS (VIN-VOUT)=5V 25°C, 30mS pulse fRIPPLE=120Hz, (VIN-VOUT)=2V, VRIPPLE=1VPP 125°C, 1000Hrs % of VOUT, 10Hz≤f≤10kHz 60 MIN 1.0 TYP 50 1.5 0.01 75 0.03 0.003 MAX 120 2.0 0.1 UNITS µA A %/W dB % % *Note 1 - For fixed option, VINMIN = VOUT + 1.5V - For adjustable option, VINMIN = VIN - VOUT = 1.4V *Note 2 - Dropout voltage is the input voltage minus output voltage that produces a 1% decrease in output voltage with respect to the nominal output voltage at VIN = VOUT + 1.5V Apr 20-07 Rev B SPX1117 800mA Low Dropout Voltage Regulator © 2007 Sipex Corporation 3 TYPICAL PERFORMANCE CHARACTERISTICS 3.320 3.315 3.310 3.305 3.300 3.295 3.290 3.285 3.280 10 100 Output Current (mA) 1000 3.325 3.320 Vout (V) Output Voltage 3.315 3.310 3.305 3.300 4.5 6.5 8.5 10.5 Vin (V) 12.5 14.5 Figure 1. Load Regulation for SPX1117M3-3.3; VIN=4.8V Figure 2. Line Regulation for SPX1117M3-3.3; IOUT=10mA Dropout Voltage (V) 1.3 1.2 1.1 1.0 0.9 100 200 300 400 500 600 700 800 900 1000 Current Limit (A) 2.00 1.50 1.00 0.50 0.00 -50 -25 0 25 50 75 100 125 Io (mA) Temp ( oC) Figure 4. Current Limit for SP1117M3-3.3; VIN=4.8V, CIN=COUT=1µF, IOUT pulsed from 10mA to Current Limit Figure 3. Dropout Voltage vs Output Current for SPX1117M3-3.3; VIN=4.8V, COUT=2.2µF Output Deviation (mV) 100 0 125°C 22µF 1.275 1.27 1.265 1.26 1.255 1.25 1.245 1.24 1.235 1.23 1.225 -50 1.25v Adj -100 1.5 Indicating Current Limit Starts Vout (V) Output Current (A) 1.0 0.5 0 V = 4.0V V =3.3V Fixed 1 =10mA C =1µF Tan Cap C =2.2µF Tan Cap IN IN O IN OUT -30 -10 10 30 50 70 90 110 130 0 0.1 0.2 0.3 0.4 0.5 0.6 Time (ms) 0.7 0.8 0.9 1.0 Temp (C) Figure 5. Current Limit for SPX1117M3-3.3, Output Voltage Deviation with IOUT=10mA to 1A Step Figure 6. VOUT vs Temperature, VIN=2.5V, IOUT=10mA Apr 20-07 Rev B SPX1117 800mA Low Dropout Voltage Regulator © 2007 Sipex Corporation 4 TYPICAL PERFORMANCE CHARACTERISTICS: Continued 1.53 1.52 1.51 Vout (V) 1.84 1.5v Adj 1.5v Fixed Vout (V) 1.83 1.82 1.81 1.8 1.79 1.78 1.77 1.8v Adj 1.8v Fixed 1.5 1.49 1.48 1.47 -50 -30 -10 10 30 50 Temp (C) 70 90 110 130 1.76 -50 -30 -10 10 30 50 Temp (C) 70 90 110 130 Figure 7. VIN=3.0V, IOUT=10mA Figure 8. VIN=3.3V, IOUT=10mA 2.92 2.5v Adj 2.5v Fixed Vout (V) 2.55 2.54 2.53 2.52 2.51 2.5 2.49 2.48 2.47 2.46 2.45 -50 2.9 2.88 2.86 2.84 2.82 2.8 -50 2.85v Adj 2.85v Fixed Vout (V) -30 -10 10 30 50 Temp (C) 70 90 110 130 -30 -10 10 30 50 Temp (C) 70 90 110 130 Figure 9. VIN=4.0V, IOUT=10mA Figure 10. VIN=4.85V, IOUT=10mA 3.06 3.04 3.02 3v Adj 3v Fixed Vout (V) 3.38 3.36 3.34 3.32 3.3 3.28 -30 -10 10 30 50 70 90 110 130 3.3v Adj 3.3v Fixed Vout (V) 3 2.98 2.96 2.94 -50 3.26 -50 -30 -10 10 30 50 70 90 110 130 Temp (C) Temp (C) Figure 11. VIN=4.85V, IOUT=10mA Output Voltage Change, mV 6 4 2 Figure 12. VIN=5.0V, IOUT=10mA 1.816 1.815 1.814 1.813 1.812 1.811 1.81 1.809 1.808 1.807 1.806 -40 -20 0 20 40 Ambient Temperature, *C 60 800mA 400mA 10mA -2 -4 -6 -8 -40 -20 0 20 40 60 80 100 Ambient Temperature,*C V out, V 0 80 100 Figure 13. Line Regulation vs Temperature. VOUT=1.8V (adjustable), VIN= 3.3V 0.4 0.3 -40°C +25°C +85°C Figure 14. Output Voltage vs Temperature at different Current Loads, VIN=3.3V, VOUT = 1.8V Adjustable Vout tolerance,% 0.2 0.1 0 -0.1 -0.2 -0.3 3 4 Vin, V 5 6 Figure 15. Line Regulation at ILOAD=800mA over Temperature, VOUT=1.8V adjustable Apr 20-07 Rev B SPX1117 800mA Low Dropout Voltage Regulator © 2007 Sipex Corporation 5 APPLICATION INFORMATION Output Capacitor To ensure the stability of the SPX1117, an output capacitor of at least 2.2µF (tantalum or ceramic) or 10µF (aluminum) is required. The value may change based on the application requirements of the output load or temperature range. The value of ESR can vary based on the type of capacitor used in the applications to guarantee stability. The recommended value for ESR is 0.5Ω or less. A larger value of output capacitance (up to 100µF) can improve the load transient response. Soldering Methods The SPX1117 SOT-223 package is designed to be compatible with infrared reflow or vapor-phase reflow soldering techniques. During soldering, the non-active or mildly active fluxes may be used. The SPX1117 die is attached to the heatsink lead which exits opposite the input, output, and ground pins. Figure 16. Load Step Response (0 to 800mA), Vin=3.3V, Vout=1.8V, Cin=10µF, Cout=2.2µF, Ceramic; 1 = Vout, 4= Iload Hand soldering and wave soldering should be avoided since these methods can cause damage to the device with excessive thermal gradients on the package. The SOT-223 recommended soldering method are as follows: vapor phase reflow and infrared reflow with the component preheated to within 65°C of the soldering temperature range. Figure 17. Load Step Response (0 to 800mA), Vin=3.3V, Vout=1.8V, Cin=10µF, Cout=2.2µF, OSCON; 1 = Vout, 4= Iload © 2007 Sipex Corporation Apr 20-07 Rev B SPX1117 800mA Low Dropout Voltage Regulator 6 APPLICATION INFORMATION: Continued Thermal Characteristics The thermal resistance of SPX1117 (SOT-223 Package) is 15°C/W from junction to tab and 31 °C/W from tab to ambient for a total of 46 °C/W from junction to ambient (Table 1). The SPX1117 features the internal thermal limiting to protect the device during overload conditions. Special care needs to be taken during continuous load conditions such that the maximum junction temperature does not exceed 125 °C. Thermal protection is activated at >155°C and deactiviated at