SGA-2163

SGA-2163 Product Description The SGA-2163 is a high performance SiGe HBT MMIC Amplifier. A Darlington configuration featuring 1 micron emitters provides high FT and excellent thermal perfomance. The heterojunction increases breakdown voltage and minimizes leakage current between junctions. Cancellation of emitter junction non-linearities results in higher suppression of intermodulation products. Only 2 DC-blocking capacitors, a bias resistor and an optional RF choke are required for operation. The matte tin finish on Sirenza’s lead-free package utilizes a post annealing process to mitigate tin whisker formation and is RoHS compliant per EU Directive 2002/95. This package is also manufactured with green molding compounds that contain no antimony trioxide nor halogenated fire retardants. Gain & Return Loss vs. Freq. @TL=+25°C 12 GAIN Return Loss (dB) 9 Gain (dB) IRL -10 0 SGA-2163Z Pb RoHS Compliant & Green Package DC-5000 MHz, Cascadable SiGe HBT MMIC Amplifier Product Features • Now available in Lead Free, RoHS Compliant, & Green Packaging • Broadband Operation: DC-5000 MHz • Cascadable 50 Ohm • Operates From Single Supply • Low Thermal Resistance Package 6 -20 ORL Applications • PA Driver Amplifier 3 -30 0 0 1 2 3 Frequency (GHz) 4 5 -40 • Cellular, PCS, GSM, UMTS • IF Amplifier • Wireless Data, Satellite Symbol G Parameter Small Signal Gain Units dB Frequency 850 MHz 1950 MHz 2400 MHz 850 MHz 1950 MHz 850 MHz 1950 MHz Min. 9.5 Typ. 10.5 9.8 9.6 7.1 6.2 21.0 18.0 5000 Max. 11.5 P1dB OIP3 Output Pow er at 1dB Compression Output Third Order Intercept Point dBm dBm MHz dB dB dB V mA °C/W Bandw idth Det ermined by Ret urn Loss (>10dB) IRL ORL NF VD ID RTH, j-l Input Return Loss Output Return Loss Noise Figure Device Operating Voltage Device Operating Current Thermal Resistance (junction to lead) Test Conditions: VS = 5 V RBIAS = 140 Ohms 1950 MHz 1950 MHz 1950 MHz 1.9 17 22.5 24.8 4.4 2.2 20 255 2.5 23 ID = 20 mA Typ. TL = 25ºC OIP3 Tone Spacing = 1 MHz, Pout per tone = -10 dBm ZS = ZL = 50 Ohms The information provided herein is believed to be reliable at press time. Sirenza Microdevices assumes no responsibility for inaccuracies or omissions. Sirenza Microdevices assumes no responsibility for the use of this information, and all such information shall be entirely at the user’s own risk. Prices and specifications are subject to change without notice. No patent rights or licenses to any of the circuits described herein are implied or granted to any third party. Sirenza Microdevices does not authorize or warrant any Sirenza Microdevices product for use in life-support devices and/or systems. Copyright 2001 Sirenza Microdevices, Inc.. All worldwide rights reserved. 303 Technology Court, Broomfield, CO 80021 Phone: (800) SMI-MMIC 1 http://www.sirenza.com EDS-100624 Rev E SGA-2163 DC-5000 MHz Cascadable MMIC Amplifier Preliminary Typical RF Performance at Key Operating Frequencies Symbol Parameter Unit 100 Frequency Frequency (MHz) Frequency (MHz)(MHz) 500 850 1950 2400 3500 G OIP3 P1dB IRL ORL S12 NF Small Signal Gain Output Third Order Intercept Point Output Power at 1dB Compression Input Return Loss Output Return Loss Reverse Isolation Noise Figure VS = 5 V VS = 8 V RBIAS = 140 Ohms RBIAS = 39 Ohms dB dBm dBm dB dB dB dB 10.7 10.6 20.9 7.2 10.5 21.0 7.1 20.3 22.3 15.5 4.1 9.8 18.0 6.2 22.5 24.8 16.1 4.4 9.6 16.9 5.6 22.1 23.4 16.4 4.8 9.3 18.7 17.2 15.6 19.8 19.1 15.4 4.2 16.0 27.6 16.9 Test Conditions: = 20 mA Typ. IID = 80 mA Typ. D T = 25ºC TLL = 25ºC OIP Tone Spacing = 1 MHz, Pout -10 dBm OIP33 Tone Spacing = 1 MHz, Pout per tone = 0 dBm ZS = Z = 50 Ohms ZS = ZLL= 50 Ohms Absolute Maximum Ratings Noise Figure vs. Frequency VD= 2.2 V, ID= 20 mA 7 Noise Figure (dB) 6 5 4 Parameter Max. Device Current (ID) Max. Device Voltage (VD) Max. RF Input Power Absolute Limit 40 mA 4V +18 dBm +150°C -40°C to +85°C +150°C TL=+25ºC Max. Junction Temp. (TJ) Operating Temp. Range (TL) Max. Storage Temp. TL=+25ºC 3 2 0 0.5 1 1.5 2 Frequency (GHz) 2.5 3 Operation of this device beyond any one of these limits may cause permanent damage. For reliable continous operation, the device voltage and current must not exceed the maximum operating values specified in the table on page one. Bias conditions should also satisfy the following expression: IDVD < (TJ - TL) / RTH, j-l OIP3 vs. Frequency VD= 2.2 V, ID= 20 mA 30 25 OIP3 (dBm) 20 15 P1dB vs. Frequency VD= 2.2 V, ID= 20 mA 10 TL P1dB (dBm) 8 6 4 2 0 TL TL=+25ºC TL=+25ºC 10 0 0.5 1 1.5 2 Frequency (GHz) 2.5 3 0 0.5 1 1.5 2 Frequency (GHz) 2.5 3 303 Technology Court, Broomfield, CO80021 Phone: (800) SMI-MMIC 2 http://www.sirenza.com EDS-100624 Rev E SGA-2163 DC-5000 MHz Cascadable MMIC Amplifier Preliminary Typical RF Performance Over Temperature ( Bias: VD= 2.2 V, ID= 20 mA (Typ.) ) |S | vs. Frequency 12 21 |S | vs. Frequency 0 -10 S11(dB) -20 -30 11 9 S21 (dB) 6 3 TL 0 0 1 2 3 Frequency (GHz) 4 +25°C -40°C +85°C TL -40 5 +25°C -40°C +85°C 0 1 2 3 Frequency (GHz) 4 5 |S | vs. Frequency -10 -15 S12(dB) -20 -25 12 |S | vs. Frequency 0 -10 S22(dB) -20 -30 -40 5 22 TL +25°C -40°C +85°C TL -30 0 1 2 3 Frequency (GHz) 4 +25°C -40°C +85°C 0 1 2 3 Frequency (GHz) 4 5 NOTE: Full S-parameter data available at www.sirenza.com 303 Technology Court, Broomfield, CO80021 Phone: (800) SMI-MMIC 3 http://www.sirenza.com EDS-100624 Rev E SGA-2163 DC-5000 MHz Cascadable MMIC Amplifier Preliminary Basic Application Circuit R BIAS Application Circuit Element Values Frequency (Mhz) Reference Designator VS 1 uF 1000 pF CD LC 1,2 500 850 1950 2400 3500 CB CD LC 220 pF 100 pF 68 nH 100 pF 68 pF 33 nH 68 pF 22 pF 22 nH 56 pF 22 pF 18 nH 39 pF 15 pF 15 nH RF in CB 3 SGA-2163 6 4,5 CB RF out Recommended Bias Resistor Values for ID=20mA RBIAS=( VS-VD ) / ID Supply Voltage(VS) 5V 140 6V 200 8V 300 10 V 390 VS RBIAS 1 uF 1000 pF RBIAS Note: RBIAS provides DC bias stability over temperature. CD LC A21 Mounting Instructions CB CB 1. Use a large ground pad area near device pins 1, 2, 4, and 5 with many plated through-holes as shown. 2. We recommend 1 or 2 ounce copper. Measurements for this data sheet were made on a 31 mil thick FR-4 board with 1 ounce copper on both sides. Part Identification Marking The part will be marked with an “A21” designator on the top surface of the package. Pin # 3 Function RF IN Description RF input pin. This pin requires the use of an external DC blocking capacitor chosen for the frequency of operation. Connection to ground. Use via holes for best performance to reduce lead inductance as close to ground leads as possible. 654 654 1, 2, 4, 5 GND A21 123 A21Z 6 123 RF OUT/ RF output and bias pin. DC voltage is BIAS present on this pin, therefore a DC blocking capacitor is necessary for proper operation. Caution: ESD sensitive Appropriate precautions in handling, packaging and testing devices must be observed. Part Number Ordering Information P art N umber S GA -2163 S GA -2163Z R eel S iz e 7" 7" D evices/R eel 3000 3000 303 Technology Court, Broomfield, CO80021 Phone: (800) SMI-MMIC 4 http://www.sirenza.com EDS-100624 Rev E SGA-2163 DC-5000 MHz Cascadable MMIC Amplifier SOT-363 PCB Pad Layout Dimensions in inches [millimeters] Preliminary RF OUT RF IN Notes: 1. Provide a large ground pad area under device pins 1, 2, 4, & 5 with many plated via holes as shown. 2. Dimensions given for 50 Ohm RF I/O lines are for 31 mil thick Getek. Scale accordingly for different board thicknesses and dielectric contants. 3. We recommend 1 or 2 ounce copper. Measurements for this data sheet were made on a 31 mil thick Getek with 1 ounce copper on both sides. SOT-363 Nominal Package Dimensions Dimensions in inches [millimeters] A link to the SOT-363 package outline drawing with full dimensions and tolerances may be found on the product web page at www.sirenza.com. 303 Technology Court, Broomfield, CO80021 Phone: (800) SMI-MMIC 5 http://www.sirenza.com EDS-100624 Rev E