SGA-4163

SGA-4163 Product Description The SGA-4163 is a high performance SiGe HBT MMIC Amplifier. A Darlington configuration featuring 1 micron emitters provides high FT and excellent thermal perfomance. The heterojunction increases breakdown voltage and minimizes leakage current between junctions. Cancellation of emitter junction non-linearities results in higher suppression of intermodulation products. Only 2 DC-blocking capacitors, a bias resistor and an optional RF choke are required for operation. SGA-4163Z Pb RoHS Compliant & Green Package DC-5000 MHz, Cascadable SiGe HBT MMIC Amplifier The matte tin finish on Sirenza’s lead-free package utilizes a post annealing process to mitigate tin whisker formation and is RoHS Product Features compliant per EU Directive 2002/95. This package is also manufactured with green molding compounds that contain no antimony • Now available in Lead Free, RoHS Compliant, & Green Packaging trioxide nor halogenated fire retardants. • Broadband Operation: DC-5000 MHz Gain & Return Loss vs. Frequency 16 12 Gain (dB) 8 4 0 0 1 VD= 3.2 V, ID= 45 mA (Typ.) 0 -10 -20 Return Loss (dB) • Cascadable 50 Ohm • Operates From Single Supply • Low Thermal Resistance Package GAIN ORL IRL Applications • • • • PA Driver Amplifier Cellular, PCS, GSM, UMTS IF Amplifier Wireless Data, Satellite -30 TL=+25ºC -40 2 3 4 Frequency (GHz) 5 6 Symbol G Parameter Small Signal Gain Units dB Frequency 850 MHz 1950 MHz 2400 MHz 850 MHz 1950 MHz 850 MHz 1950 MHz Min. 9.5 Typ. 10.5 9.7 9.6 13.0 12.1 29.7 25.4 5000 Max. 11.5 P1dB OIP3 Output Pow er at 1dB Compression Output Third Order Intercept Point dBm dBm MHz dB dB dB V mA °C/W Bandw idth Determined by Return Loss (>10dB) IRL ORL NF VD ID RTH, j-l Input Return Loss Output Return Loss Noise Figure Device Operating Voltage Device Operating Current Thermal Resistance (junction to lead) VS = 8 V RBIAS = 110 Ohms 1950 MHz 1950 MHz 1950 MHz 2.9 41 28.0 20.1 5.0 3.2 45 255 3.5 49 Test Conditions: ID = 45 mA Typ. TL = 25ºC OIP3 Tone Spacing = 1 MHz, Pout per tone = -5 dBm ZS = ZL = 50 Ohms The information provided herein is believed to be reliable at press time. Sirenza Microdevices assumes no responsibility for inaccuracies or omissions. Sirenza Microdevices assumes no responsibility for the use of this information, and all such information shall be entirely at the user’s own risk. Prices and specifications are subject to change without notice. No patent rights or licenses to any of the circuits described herein are implied or granted to any third party. Sirenza Microdevices does not authorize or warrant any Sirenza Microdevices product for use in life-support devices and/or systems. Copyright 2001 Sirenza Microdevices, Inc.. All worldwide rights reserved. 303 Technology Court, Broomfield, CO. 80021 Phone: (800) SMI-MMIC 1 http://www.sirenza.com EDS-100638 Rev. G SGA-4163 DC-5000 MHz Cascadable MMIC Amplifier Preliminary Typical RF Performance at Key Operating Frequencies Symbol Parameter Unit 100 500 Frequency Frequency (MHz) Frequency (MHz)(MHz) 850 1950 2400 3500 G OIP3 P1dB IRL ORL S12 NF Small Signal Gain Output Third Order Intercept Point Output Power at 1dB Compression Input Return Loss Output Return Loss Reverse Isolation Noise Figure VS = 8 V VS = 8 V RBIAS = 110 Ohms RBIAS = 39 Ohms dB dBm dBm dB dB dB dB 10.3 10.2 30.2 12.9 10.5 29.7 13.0 23.7 24.3 16.3 4.8 9.7 25.4 12.1 28.0 20.1 17.2 5.0 9.6 23.0 11.1 36.7 18.7 17.6 5.3 9.4 29.1 19.7 15.5 26.7 20.8 16.0 4.6 16.6 17.6 18.4 Test Conditions: = 45 mA Typ. IID = 80 mA Typ. D T = 25ºC TLL = 25ºC OIP Tone Spacing = 1 MHz, Pout per tone = -5 dBm OIP33 Tone Spacing = 1 MHz, Pout per tone = 0 dBm ZS = Z = 50 Ohms ZS = ZLL= 50 Ohms Noise Figure vs. Frequency VD= 3.2 V, ID= 45 mA (Typ.) 7 6 5 4 3 Absolute Maximum Ratings Parameter Max. Device Current (ID) Max. Device Voltage (VD) Absolute Limit 90 mA 5V +18 dBm +150°C -40°C to +85°C +150°C Noise Figure (dB) Max. RF Input Power Max. Junction Temp. (TJ) Operating Temp. Range (TL) Max. Storage Temp. TL=+25ºC 2 0 0.5 1 1.5 2 Frequency (GHz) 2.5 3 Operation of this device beyond any one of these limits may cause permanent damage. For reliable continous operation, the device voltage and current must not exceed the maximum operating values specified in the table on page one. Bias conditions should also satisfy the following expression: IDVD < (TJ - TL) / RTH, j-l OIP3 vs. Frequency VD=3.2 V, ID= 45 mA (Typ.) 35 30 OIP3 (dBm) P1dB (dBm) 18 15 12 9 P1dB vs. Frequency VD= 3.2 V, ID= 45 mA (Typ.) 25 20 TL=+25ºC 15 0 0.5 1 1.5 2 Frequency (GHz) 2.5 3 6 0 0.5 1 1.5 2 Frequency (GHz) TL=+25ºC 2.5 3 303 Technology Court, Broomfield, CO 80021 Phone: (800) SMI-MMIC 2 http://www.sirenza.com EDS-100638 Rev. G SGA-4163 DC-5000 MHz Cascadable MMIC Amplifier Preliminary Typical RF Performance Over Temperature ( Bias: VD= 3.2 V, ID= 45 mA (Typ.) ) |S | vs. Frequency 16 12 S21(dB) 8 4 21 |S | vs. Frequency 0 -10 S11(dB) -20 -30 11 TL 0 0 1 2 3 4 Frequency (GHz) 5 +25°C -40°C +85°C TL -40 6 +25°C -40°C +85°C 0 1 2 3 4 Frequency (GHz) 5 6 |S | vs. Frequency -10 -15 S12(dB) S22(dB) 12 |S | vs. Frequency 0 -10 22 -20 -25 -20 -30 TL -30 0 1 2 3 4 Frequency (GHz) 5 +25°C -40°C +85°C TL -40 +25°C -40°C +85°C 6 0 1 2 3 4 Frequency (GHz) 5 6 NOTE: Full S-parameter data available at www.sirenza.com 303 Technology Court, Broomfield, CO 80021 Phone: (800) SMI-MMIC 3 http://www.sirenza.com EDS-100638 Rev. G SGA-4163 DC-5000 MHz Cascadable MMIC Amplifier Preliminary Basic Application Circuit R BIAS Application Circuit Element Values Frequency (Mhz) Reference Designator 500 850 1950 2400 3500 VS 1 uF 1000 pF CD LC 1,2 CB CD LC 220 pF 100 pF 68 nH 100 pF 68 pF 33 nH 68 pF 22 pF 22 nH 56 pF 22 pF 18 nH 39 pF 15 pF 15 nH RF in CB 3 SGA-4163 6 4,5 CB RF out Recommended Bias Resistor Values for ID=45mA RBIAS=( VS-VD ) / ID Supply Voltage(VS) RBIAS 6V 62 8V 110 10 V 150 12 V 200 VS RBIAS 1 uF 1000 pF Note: RBIAS provides DC bias stability over temperature. CD LC A41 Mounting Instructions 1. Use a large ground pad area near device pins 1, 2, CB CB 4, and 5 with many plated through-holes as shown. 3. We recommend 1 or 2 ounce copper. Measurements for this data sheet were made on a 31 mil thick FR-4 board with 1 ounce copper on both sides. Pin # 3 Function RF IN Description RF input pin. This pin requires the use of an external DC blocking capacitor chosen for the frequency of operation. Connection to ground. For optimum RF performance, use via holes as close to ground leads as possible to reduce lead inductance . Part Identification Marking 654 654 1, 2, 4, 5 GND A41 123 A41Z 123 6 RF output and bias pin. DC voltage is RF OUT/ present on this pin, therefore a DC BIAS blocking capacitor is necessary for proper operation. Caution: ESD sensitive Appropriate precautions in handling, packaging and testing devices must be observed. Part Number Ordering Information Part Number Reel Size Devices/Reel SGA-4163 SGA-4163Z 7" 7" 3000 3000 303 Technology Court, Broomfield, CO 80021 Phone: (800) SMI-MMIC 4 http://www.sirenza.com EDS-100638 Rev. G SGA-4163 DC-5000 MHz Cascadable MMIC Amplifier SOT-363 PCB Pad Layout Dimensions in inches [millimeters] Preliminary RF OUT RF IN Notes: 1. Provide a large ground pad area under device pins 1, 2, 4, & 5 with many plated via holes as shown. 2. Dimensions given for 50 Ohm RF I/O lines are for 31 mil thick Getek. Scale accordingly for different board thicknesses and dielectric contants. 3. We recommend 1 or 2 ounce copper. Measurements for this data sheet were made on a 31 mil thick Getek with 1 ounce copper on both sides. SOT-363 Nominal Package Dimensions Dimensions in inches [millimeters] A link to the SOT-363 package outline drawing with full dimensions and tolerances may be found on the product web page at www.sirenza.com. 303 Technology Court, Broomfield, CO 80021 Phone: (800) SMI-MMIC 5 http://www.sirenza.com EDS-100638 Rev. G