ABA3100RS3P1

ABA3100 1 GHz Balanced Low Noise Linear Amplifier Data Sheet FEATURES • 12 dB Gain • +5 V Nominal Supply Voltage • High Linearity • Low Noise Figure: 2.7 dB (typ) • Characterized at +25 dBmV output power • Wide Band operation to beyond 1 GHz • -40 to +85 °C • RoHS-Compliant Package Option APPLICATIONS • Driver Amplifier • CATV - Distribution / Drop Amplifiers S3 Package Modified 16 Pin SOIC • Set Top Boxes • Home Gateway PRODUCT DESCRIPTION The ABA3100 is a monolithic IC intended for use in applications requiring high linearity, such as Cellular Telephone Base Station Driver Amplifiers, CATV Fiber Receiver and Distribution Amplifiers, CATV Drop Amplifiers, CATV Set Top Boxes and Home Gateways. Offered in a modified 16 lead surface mount SOIC package, it is well suited for use in amplifiers where small size, reduced component count, and high reliability are important. RF IN 12 dB RF OUT RF IN 12 dB RF OUT Figure 1: Block Diagram 204193B • Skyworks Proprietary and Confidential Information • Products and Product Information are Subject to Change Without Notice • September 16, 2016 ABA3100 1 FB1 GND 16 2 RF IN1 GND 15 3 RF IN1 RF OUT1 /VDD1 14 4 GND GND 13 5 GND GND 12 6 RF IN2 RF OUT2 /VDD2 11 7 RF IN2 GND 10 8 FB2 I ADJ 9 Figure 2: Pinout Diagram Table 1: Pin Description PIN NAME DESCRIPTION PIN NAME DESCRIPTION 1 FB1 Feedback for Amplifier A1 9 IADJ Current Adjust 2 RFIN1 RF Input of Amplifier A1 10 GND Ground 3 RFIN1 RF Input of Amplifier A1 11 RFOUT2VDD2 RF output and VDD of Amplifier A2 4 GND Ground 12 GND Ground 5 GND Ground 13 GND Ground 6 RFIN2 RF Input of Amplifier A2 14 RFOUT1/VDD1 RF Output and VDD of Amplifier A1 7 RFIN2 RF Input of Amplifier A2 15 GND Ground 8 FB2 Feedback for Amplifier A2 16 GND Ground 2 Data Sheet September 16, 2016 • Skyworks Proprietary and Confidential Information • Products and Product Information are Subject to Change Without Notice • 204193B ABA3100 ELECTRICAL CHARACTERISTICS Table 2: Absolute Minimum and Maximum Ratings PARAMETER MIN MAX UNITS Analog Supply (pins 11, 14) 0 +12 VDC RF P o we r a t Inp uts (p i ns 2 , 3 , 6, 7) - +10 dBm - 65 +150 °C Soldering Temperature - 260 °C Soldering Time - 5.0 Sec. Storage Temperature Stresses in excess of the absolute ratings may cause permanent damage. Functional operation is not implied under these conditions. Exposure to absolute ratings for extended periods of time may adversely affect reliability. Notes: 1. Pins 1, 2, 3, 6, 7 and 8 should be AC-coupled. No external DC bias should be applied. 2. Pin 9 should be AC-grounded. No external DC bias should be applied. Table 3: Operating Ranges PARAMETER MIN TYP MAX UNITS RF Input / Output Frequency 50 - 1000 MHz Analog Supply: VDD (pins 11, 14) +4.5 +5 +9 VDC Case Temperature: TA -40 - +85 °C The device may be operated safely over these conditions; however, parametric performance is guaranteed only over the conditions defined in the electrical specifications. Data Sheet 204193B • Skyworks Proprietary and Confidential Information • Products and Product Information are Subject to Change Without Notice • September 16, 2016 3 ABA3100 Table 4: Electrical Specifications (Ta = +25 °C, Vdd = + 5 VDC, Test System = 75Ω) PARAMETER MIN TYP MAX UNITS Gain 11 12 13 dB Noise Figure - 2.5 2.7 3.2 3.0 3.5 4.0 dB dB dB 10 18 - dB Input/Output Return Loss -72 dBc -75 dBc 2nd Order Input Intercept Point (OIP2) (2) +60 dBm 3rd Order Input Intercept Point (OIP3) (2) +35 dBm CSO CTB (1) (1) Thermal Resistance Current Consumption (3,4) - - 33  C/W 120 150 170 mA COMMENTS 50 MHz - 350 MHz 350 MHz - 550 MHz 550 MHz - 860 MHz Notes: (1) 132 channels, +25 dBmV per channel (measured at the output), 6 MHz channel spacing. (2) Two tones: 397 MHz and 403 MHz, +4 dBm per tone. (3) Characterized with IADJ pin floating. (4) Adding a shunt resistor from the IADJ pin to ground will lower current, but with some decrease in perfomance. 4 Data Sheet September 16, 2016 • Skyworks Proprietary and Confidential Information • Products and Product Information are Subject to Change Without Notice • 204193B ABA3100 PERFORMANCE DATA Figure Figure 3: Typical Gain Gain (S21)(S21) vs. Frequency 3: Typical vs. Frequency 15 14.5 14 13.5 Gain (dB) 13 12.5 12 11.5 11 10.5 10 0 100 200 300 400 500 600 700 800 900 1000 Frequency (MHz) ? Typical Input Return vs. Frequency Figure 4:Figure Typical Input Return Loss Loss (S11)(S11) vs. Frequency 5 0 Input Return Loss (dB) -5 -10 -15 -20 -25 -30 -35 -40 0 100 200 300 400 500 600 700 800 900 1000 Frequency (MHz) Data Sheet 204193B • Skyworks Proprietary and Confidential Information • Products and Product Information are Subject to Change Without Notice • September 16, 2016 5 ABA3100 ?:Output TypicalReturn Output Loss Return(S22) Lossvs. (S22) vs. Frequency Figure 5: Figure Typical Frequency 5 0 Output Return Loss (dB) -5 -10 -15 -20 -25 -30 -35 -40 0 100 200 300 400 500 600 700 800 900 1000 Frequency (MHz) Figure ?: Typical Isolation vs. Frequency Figure 6: Typical Isolation (S12)(S12) vs. Frequency 0 -5 -10 Isolation (dB) -15 -20 -25 -30 -35 -40 -45 -50 0 100 200 300 400 500 600 700 800 900 1000 Frequency (MHz) 6 Data Sheet September 16, 2016 • Skyworks Proprietary and Confidential Information • Products and Product Information are Subject to Change Without Notice • 204193B ABA3100 Figure 7:Figure Typical Noise Figure vs. Frequency ?: Typical Noise Figure vs. Frequency 8 7 Noise Floor (dB) 6 5 4 3 2 1 0 100 200 300 400 500 600 700 800 900 1000 Frequency (MHz) Data Sheet 204193B • Skyworks Proprietary and Confidential Information • Products and Product Information are Subject to Change Without Notice • September 16, 2016 7 ABA3100 APPLICATION INFORMATION Figure 8: Evaluation Board Layout Not Installed +5 VDC (Vdd) C9 C11 C3 T1 C1 1 FB1 2 RF IN1 RF IN1 3 RF In C2 16 GND 15 RF GND 13 5 GND GND 12 6 RF IN2 RF IN2 8 T2 RF Out C7 11 OUT2 GND IADJ FB2 C8 14 GND RF L1 OUT1 4 7 C4 GND C10 10 L2 9 C6 C5 ABA3100 I Adj +5 VDC (Vdd) Not Installed * Connecting a resistor from IADJ to ground lowers current; normal operation is with IADJ floating. Figure 9: Evaluation Board Schematic 8 Data Sheet September 16, 2016 • Skyworks Proprietary and Confidential Information • Products and Product Information are Subject to Change Without Notice • 204193B ABA3100 Table 5: Evaluation Board Parts List ITEM DESCRIPTION QTY VENDOR VENDOR PART NUMBER C1-C4, C6, C9 0.01uF CHIP CAP. 6 MURATA GRM39X7R1103K25V C7, C8 470 pF CHIP CAP. 2 MURATA GRM39COG471J25V C10 47 uF ELEC. CAP. 1 DIGI-KEY CORP C5. C11 (not installed) L1, L2 390 nH CHIP INDUCTOR 2 COILCRAFT CONNECTORS 75  N MALE PANEL MOUNT 2 PASTERNACK ENTERPRISES PE4504 T1, T2 BALUN 2 PULSE ENGINEERING CX2024 PCB 1 STANDARD PRINTED CIRCUITS, INC. EBSTA-111899 P5275-ND 1008CS-391XKBC Notes: 1. “N” Connector center pin should be approximately 80 mils in length. 2. Connector tabs must be reduced by 150 mils. 3. Device must be soldered on PC board. Figure 10: Pulse CX 2024 Balun Note: 1. Consult Pulse Engineering data sheet for more details. Data Sheet 204193B • Skyworks Proprietary and Confidential Information • Products and Product Information are Subject to Change Without Notice • September 16, 2016 9 ABA3100 PACKAGE OUTLINE Figure 11: S3 Package Outline - Modified 16 Pin SOIC 10 Data Sheet September 16, 2016 • Skyworks Proprietary and Confidential Information • Products and Product Information are Subject to Change Without Notice • 204193B ABA3100 NOTES Data Sheet 204193B • Skyworks Proprietary and Confidential Information • Products and Product Information are Subject to Change Without Notice • September 16, 2016 11 ABA3100 ORDERING INFORMATION ORDER NUMBER TEMPERATURE RANGE PACKAGE DESCRIPTION ABA3100S3TR -40 to +85 °C Modified 16 Pin SOIC 3,500 piece Tape and Reel ABA3100S3P0 -40 to +85 °C Modified 16 Pin SOIC Plastic tubes (50 pieces per tube) ABA3100RS3P1 -40 to +85 °C RoHS-Compliant Modified 16 Pin SOIC 3,500 piece Tape and Reel COMPONENT PACKAGING Copyright © 2016 Skyworks Solutions, Inc. All Rights Reserved. Information in this document is provided in connection with Skyworks Solutions, Inc. (“Skyworks”) products or services. These materials, including the information contained herein, are provided by Skyworks as a service to its customers and may be used for informational purposes only by the customer. Skyworks assumes no responsibility for errors or omissions in these materials or the information contained herein. Skyworks may change its documentation, products, services, specifications or product descriptions at any time, without notice. Skyworks makes no commitment to update the materials or information and shall have no responsibility whatsoever for conflicts, incompatibilities, or other difficulties arising from any future changes. No license, whether express, implied, by estoppel or otherwise, is granted to any intellectual property rights by this document. Skyworks assumes no liability for any materials, products or information provided hereunder, including the sale, distribution, reproduction or use of Skyworks products, information or materials, except as may be provided in Skyworks Terms and Conditions of Sale. THE MATERIALS, PRODUCTS AND INFORMATION ARE PROVIDED “AS IS” WITHOUT WARRANTY OF ANY KIND, WHETHER EXPRESS, IMPLIED, STATUTORY, OR OTHERWISE, INCLUDING FITNESS FOR A PARTICULAR PURPOSE OR USE, MERCHANTABILITY, PERFORMANCE, QUALITY OR NON-INFRINGEMENT OF ANY INTELLECTUAL PROPERTY RIGHT; ALL SUCH WARRANTIES ARE HEREBY EXPRESSLY DISCLAIMED. SKYWORKS DOES NOT WARRANT THE ACCURACY OR COMPLETENESS OF THE INFORMATION, TEXT, GRAPHICS OR OTHER ITEMS CONTAINED WITHIN THESE MATERIALS. SKYWORKS SHALL NOT BE LIABLE FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO ANY SPECIAL, INDIRECT, INCIDENTAL, STATUTORY, OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION, LOST REVENUES OR LOST PROFITS THAT MAY RESULT FROM THE USE OF THE MATERIALS OR INFORMATION, WHETHER OR NOT THE RECIPIENT OF MATERIALS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Skyworks products are not intended for use in medical, lifesaving or life-sustaining applications, or other equipment in which the failure of the Skyworks products could lead to personal injury, death, physical or environmental damage. Skyworks customers using or selling Skyworks products for use in such applications do so at their own risk and agree to fully indemnify Skyworks for any damages resulting from such improper use or sale. Customers are responsible for their products and applications using Skyworks products, which may deviate from published specifications as a result of design defects, errors, or operation of products outside of published parameters or design specifications. Customers should include design and operating safeguards to minimize these and other risks. Skyworks assumes no liability for applications assistance, customer product design, or damage to any equipment resulting from the use of Skyworks products outside of stated published specifications or parameters. Skyworks and the Skyworks symbol are trademarks or registered trademarks of Skyworks Solutions, Inc., in the United States and other countries. Third-party brands and names are for identification purposes only, and are the property of their respective owners. Additional information, including relevant terms and conditions, posted at www.skyworksinc.com, are incorporated by reference. Skyworks Solutions, Inc. Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com Skyworks Proprietary and Confidential information • Products and Product Information are Subject to Change Without Notice 12 Data Sheet 204193B September 16, 2016