CX77105-16P

CX77105 Power Amplifier Module for CDMA/AMPS (824–849 MHz) The CX77105, a dual-mode, Code Division Multiple Access (CDMA) / Advanced Mobile Phone Service (AMPS) Power Amplifier Module (PAM), is a fully matched, 10-pin surface mount module developed for cellular handsets and wireless local loop applications. This small and efficient power amplifier module packs a full 824–849 MHz bandwidth coverage into a single compact package. The device meets the stringent IS95 CDMA linearity requirements to and exceeding 28 dBm output power, and can be driven to levels beyond 31 dBm for high efficiency in FM mode operation. A low current digital pin (VCONT) provides improved efficiency for the low RF power range of operation. Distinguishing Features • Low voltage positive bias supply (3.2 V to 4.2 V, typical) Good linearity High efficiency Dual mode operation Large dynamic range 10-pin package (4 x 4 x 1.5 mm) Power down control Low power-state control InGaP IS 95/CDMA2000 • • • • • • The single Gallium Arsenide (GaAs) Microwave Monolithic Integrated Circuit (MMIC) • contains all active circuitry in the module. The MMIC contains on-board bias circuitry, • as well as input and interstage matching circuits. The output match is realized off-chip • and within the module package to optimize efficiency and power performance into a 50 Ω load. This device is manufactured with Skyworks’ GaAs Heterojunction Bipolar Transistor (HBT) process that provides for all positive voltage DC supply operation while maintaining high efficiency and good linearity. Primary bias to the CX77105 is supplied directly from a three-cell nickel cadmium, a single-cell lithium ion, or other suitable battery with an output in the 3–4 volt range. Power down is accomplished by setting the voltage on the low current reference pin to zero volts. No external supply side switch is needed as typical “off” leakage is a few microamperes with full primary voltage supplied from the battery. Applications • • • Digital cellular (CDMA) Analog cellular (AMPS) Wireless local loop (WLL) Functional Block Diagram VREF (1) VCC1 (5) VCONT (2) VCC2 (6) Driver Stage Bias Power Stage Bias RF IN (4) Input Match DA Inter Stage Match PA Output Match (8) RF OUT MMIC MODULE (3, 7, 9, 10) GND (3, 7, 9, 10) GND Data Sheet © 2001, 2002 Skyworks Solutions, Inc., All Rights Reserved. 101787A December 10, 2002 Electrical Specifications CX77105 Power Amplifier Module for CDMA/AMPS (824–849 MHz) Electrical Specifications The following tables list the electrical characteristics of the CX77105 Power Amplifier. Table 2 lists the recommended operating conditions for achieving the electrical performance listed in Table 4. Table 3 lists the electrical performance of the CX77105 Power Amplifier over the recommended operating conditions. Table 1. Absolute Maximum Ratings(1) Parameter RF Input Power Supply Voltage Reference Voltage Case Operating Temperature Storage Temperature NOTE(S): (1) Symbol PIN VCC VREF TC TSTG Minimum — — — –30 –55 Nominal 4.0 3.4 3.0 25 — Maximum 7.0 6.0 3.1 +110 +125 Unit dBm Volts Volts o o C C No damage assuming only one parameter is set at limit at a time with all other parameters set at or below nominal value. Table 2. Recommended Operating Conditions Parameter Supply Voltage PA On Reference Voltage PA Off High Bias Low Bias VREF VCONT VCONT FO TO — 0.0 2.5 824.0 –30 — — — 836.5 — 0.5 0.5 Volts 3.0 849.0 +85 MHz °C Symbol VCC VREF Minimum 3.2 2.95 Nominal 3.4 3.0 Maximum 4.2 3.05 Unit Volts Volts Mode Input Impedance >2.5 kΩ Operating Frequency Operating Temperature Table 3. Power Range Truth Table Power Mode High Power Low Power Shut Down VREF 3.0 V 3.0 V 0.0 V VCONT 0.0–0.5 V 2.5–3.0 V 0.0 V Range 16 dBm–28 dBm ≤ 16 dBm — 2 Skyworks Solutions, Inc. Proprietary 101787A December 10, 2002 CX77105 Power Amplifier Module for CDMA/AMPS (824–849 MHz) Table 4. Electrical Specifications for CDMA / AMPS Nominal Operating Conditions(1) Characteristics Digital Mode Gain conditions Analog Mode Digital Mode Power Added Efficiency Analog Mode Total Supply Current Quiescent Current Reference Current Control Current Total Supply current in Power-down Mode 885 kHz offset Adjacent Channel Power(2)(3) 1.98 MHz offset Electrical Specifications Symbol GLOW GHIGH GP PAELOW PAEHIGH PAEa ICC_LOW ICC_HIGH IQ_LOW IQ_HIGH IREF ICTRL IPD ACP1LOW ACP1HIGH ACP2LOW Condition VCONT ≥ 2.5 V PO = 16 dBm VCONT ≤ 0.5 V PO = 28 dBm VCONT ≤ 0.5 V PO = 31 dBm VCONT ≥ 2.5 V PO = 16 dBm VCONT ≤ 0.5 V PO = 28 dBm VCONT ≤ 0.5 V PO = 31 dBm PO = 16 dBm PO = 28 dBm VCONT ≥ 2.5 V VCONT ≤ 0.5 V — VCONT = 2.5 V VCC = 3.4 V VREF = 0 V VCONT ≥ 2.5 V PO ≤ 16 dBm VCONT ≤ 0.5 V PO ≤ 28 dBm VCONT ≥ 2.5 V PO ≤ 16 dBm or VCONT ≤ 0.5 V PO ≤ 28 dBm PO ≤ 28 dBm PO ≤ 28 dBm Minimum 25.0 28.5 27.5 7.6 37.0 48.0 — — 40 60 — 200 — — — — Typical 27.0 29.0 29.0 8.5 40.0 55.0 137 490 55 78 2.5 235 3.0 –49.0 –50.0 –65.0 Maximum 28.0 31.0 31.0 — — — 153 500 75 105 5.0 500 5.0 –47.3 –47.0 –59.0 Unit dB % mA mA mA µA µA dBc ACP2HIGH FO2 FO3 — — — –60.0 –38.0 –59.0 –57.4 –35.0 dBc –45.0 Harmonic Suppression Secon d Third 101787A December 10, 2002 Skyworks Solutions, Inc. Proprietary 3 Electrical Specifications CX77105 Power Amplifier Module for CDMA/AMPS (824–849 MHz) Table 4. Electrical Specifications for CDMA / AMPS Nominal Operating Conditions(1) Characteristics Noise Power in RX Band 869-894 MHz Noise Figure Input Voltage Standing Wave Ratio Stability (Spurious output) Ruggedness—No damage(4) NOTE(S): (1) (2) Symbol RxBN NF VSWR S Ru Condition PO ≤ 28 dBm — — 5:1 VSWR all phases PO ≤ 28 dBm Minimum — — — — 10:1 Typical –137 4.6 — — — Maximum — 5.0 1.9:1 –60.0 — Unit dBm/Hz dB — dBc VSWR VCC = +3.4 V, VREF = +3.0 V, Freq = 836.5 MHz, TC = 25 °C, unless otherwise specified. ACP is specified per IS95 as the ratio of the total in-band power (1.23 MHz BW) to adjacent power in a 30 kHz BW. (3) CDMA2000 is configured as DCCH = 9600, SCHO = 9600, PCH (Walsh 0) = – 3.75 dB, and Peak-to-Average Ratio (CCDF = 1%) = 4.5 dB. For CDMA2000, 0.5 dB back-off in output power is required. (4) All phases, time = 10 seconds. Table 5. Electrical Specifications for CDMA / AMPS Recommended Operating Conditions(1) Characteristics Digital Mode Gain conditions Analog Mode 1.25 MHz offset Adjacent Channel Power(2)(3) 1.98 MHz offset ACP2HIGH Second Harmonic Suppression Third F O3 F O2 Symbol GLOW GHIGH GP ACP1LOW ACP1HIGH ACP2LOW Condition VCONT ≥ 2.5 V PO = 16 dBm VCONT ≤ 0.5 V PO = 28 dBm VCONT ≤ 0.5 V PO = 31 dBm VCONT ≥ 2.5 V PO ≤ 16 dBm VCONT ≤ 0.5 V PO ≤ 28 dBm VCONT ≥ 2.5 V PO ≤ 16 dBm or VCONT ≤ 0.5 V PO ≤ 28 dBm PO ≤ 28 dBm PO ≤ 28 dBm Minimum 24.0 27.1 24.0 — — — Maximum 28.5 32.4 33.0 –44 –44 –56 Unit dB dBc dBc dBc — — — –56 –30 –40 dBc dBc dBc 4 Skyworks Solutions, Inc. Proprietary 101787A December 10, 2002 CX77105 Power Amplifier Module for CDMA/AMPS (824–849 MHz) Table 5. Electrical Specifications for CDMA / AMPS Recommended Operating Conditions(1) Characteristics Noise Power in RX Band 869-894 MHz Noise Figure Input Voltage Standing Wave Ratio (VSWR) Stability (Spurious output) Ruggedness – No damage(4) NOTE(S): (1) (2) Electrical Specifications Symbol RxBN NF VSWR S Ru Condition PO ≤ 28 dBm — — 5:1 VSWR All phases PO ≤ 28dBm Minimum — — — — 10:1 Maximum –134.0 7.0 2.0:1 –60.0 — Unit dBm/Hz dB — dBc VSWR Per Table 2, unless otherwise specified. ACP is specified per IS95 as the ratio of the total in-band power (1.23 MHz BW) to adjacent power in a 30 kHz BW. (3) CDMA2000 is configured as DCCH = 9600, SCHO = 9600, PCH (Walsh 0) = –3.75 dB, and Peak-to-Average Ratio (CCDF = 1%) = 4.5 dB. For CDMA2000, 0.5 dB back-off in output power is required. (4) All phases, time = 10 seconds. 101787A December 10, 2002 Skyworks Solutions, Inc. Proprietary 5 Characterization Data CX77105 Power Amplifier Module for CDMA/AMPS (824–849 MHz) Characterization Data The following graphs illustrate the characteristics of a typical CX77105 power amplifier designed for operation in the cellular frequency band (824–849 MHz). This amplifier was selected by characterizing a group of devices and then selecting a part with average electrical performance for both nominal and the full range of recommended operating conditions, including worst case limits. Figures 1 through 7 illustrate the digital signal characteristics of the CX77105. Shown are power sweep characteristics for key performance parameters, over temperature and frequency, up to 28.5 dBm output power. The data was taken up to and including 16 dBm output power with the bias mode control pin setting of VCONT = 2.5 volts. Beyond 16 dBm output power, the VCONT was set to 0 volts. Figure 1. Digital Mode Gain vs. Output Power VREF = 3.0 V VCC = 3.4 V 35 34 33 32 31 30 Gain (dB) 29 28 27 26 +25 ˚C +85 ˚C 25 24 23 22 21 20 0 5 10 15 20 25 30 –30 ˚C VCONT > 2.5 V VCONT < 0.5 V Output Power (dBm) 101787_009 Legend 8 24 824 @ – 30 ˚ C 30 8 37 837 @ – 30 ˚ C 30 8 49 849 @ – 30 ˚ C 30 8 24 824 @ +25 ˚ C 8 37 837 @ +25 ˚ C 8 49 849 @ +25 ˚ C 8 24 824 @ +85 ˚ C 8 37 837 @ +85 ˚ C 8 49 849 @ +85 ˚ C 6 Skyworks Solutions, Inc. Proprietary 101787A December 10, 2002 CX77105 Power Amplifier Module for CDMA/AMPS (824–849 MHz) Figure 2. Primary Bias Current vs. Output Power VREF = 3.0 V 600 Characterization Data VCC = 3.4 V 500 400 Icc (mA) VCONT > 2.5 V 300 VCONT < 0.5 V 200 100 0 0 5 10 15 20 25 30 Output Power (dBm) 101787_010 Figure 3. Power Added Efficiency vs. Output Power VREF = 3.0 V VCC = 3.4 V 45 40 35 Power Added Efficiency (%) 30 25 VCONT > 2.5 V 20 VCONT < 0.5 V 15 10 5 0 0 5 10 15 20 25 30 Output Power (dBm) 101787_011 Legend 8 24 824 @ – 30 ˚ C 30 8 37 837 @ – 30 ˚ C 30 8 49 849 @ – 30 ˚ C 30 8 24 824 @ +25 ˚ C 8 37 837 @ +25 ˚ C 8 49 849 @ +25 ˚ C 8 24 824 @ +85 ˚ C 8 37 837 @ +85 ˚ C 8 49 849 @ +85 ˚ C 101787A December 10, 2002 Skyworks Solutions, Inc. Proprietary 7 Characterization Data CX77105 Power Amplifier Module for CDMA/AMPS (824–849 MHz) Figure 4. Adjacent Channel Power for 885 kHz Offset Current vs. Output Power VREF = 3.0 V VCC = 3.4 V 80 75 Adjacent Channel Power Ratio 70 +8 5˚ C 65 +2 5˚ C 60 –3 0˚ C VCONT > 2.5 V VCONT < 0.5 V 55 50 45 40 0 5 10 15 20 25 30 Output Power (dBm) 101787_012 Figure 5. Adjacent Channel Power for 1.98 MHz Offset vs. Output Power VREF = 3.0 V 90 Vcc = 3.4 V Adjacent Channel Power Ratio (-dBc) 85 +8 5˚ 80 C +2 5˚ C 75 –3 0˚ C 70 65 60 VCONT > 2.5 V VCONT < 0.5 V 55 50 0 5 10 15 20 25 30 Output Power (dBm) Legend 8 24 824 @ – 30 ˚ C 30 8 37 837 @ – 30 ˚ C 30 8 49 849 @ – 30 ˚ C 30 8 24 824 @ +25 ˚ C 8 37 837 @ +25 ˚ C 8 49 849 @ +25 ˚ C 8 24 824 @ +85 ˚ C 8 37 837 @ +85 ˚ C 8 49 849 @ +85 ˚ C 8 Skyworks Solutions, Inc. Proprietary 101787A December 10, 2002 CX77105 Power Amplifier Module for CDMA/AMPS (824–849 MHz) Figure 6. Second Harmonic Rejection vs. Output Power Characterization Data VREF = 3.0 V VCC = 3.4 V 55 2nd Harmonic Rejection (-dBc) 50 45 40 35 VCONT > 2.5 V 30 0 5 10 15 20 25 30 VCONT < 0.5 V Output Power (dBm) 101787_014 Figure 7. Third Harmonic Rejection vs. Output Power VREF = 3.0 V VCC = 3.4 V 70 3rd Harmonic Rejection (-dBc) 65 60 55 VCONT > 2.5 V 50 0 5 10 15 VCONT < 0.5 V 20 25 30 Output Power (dBm) 101787_015 Legend 8 24 824 @ – 30 ˚ C 30 8 37 837 @ – 30 ˚ C 30 8 49 849 @ – 30 ˚ C 30 8 24 824 @ +25 ˚ C 8 37 837 @ +25 ˚ C 8 49 849 @ +25 ˚ C 8 24 824 @ +85 ˚ C 8 37 837 @ +85 ˚ C 8 49 849 @ +85 ˚ C 101787A December 10, 2002 Skyworks Solutions, Inc. Proprietary 9 Characterization Data CX77105 Power Amplifier Module for CDMA/AMPS (824–849 MHz) Figure 8. Noise Figure as Function of Operating Conditions 7 824 6 836.5 849 COLD ROOM TEMPERATURE HOT 5 Noise Figure (dB) 4 3 2 1 0 3.2 V –30 ˚C 3.4 V –30 ˚C 4.2 V –30 ˚C 3.2 V +25 ˚C 3.4 V +25 ˚C 4.2 V +25 ˚C 3.2 V +85 ˚C 3.4 V +85 ˚C 4.2 V +85 ˚C Collector Voltage / Case Temperature 101787_016 Figure 9. Input VSWR as Function of Operating Conditions 2.0 824 1.9 836.5 849 COLD 1.8 1.7 1.6 ROOM TEMPERATURE HOT VSWR 1.5 1.4 1.3 1.2 1.1 1.0 3.2 V –30 ˚C 3.4 V –30 ˚C 4.2 V –30 ˚C 3.2 V +25 ˚C 3.4 V +25 ˚C 4.2 V +25 ˚C 3.2 V +85 ˚C 3.4 V +85 ˚C 4.2 V +85 ˚C Collector Voltage / Case Temperature 101787_017 10 Skyworks Solutions, Inc. Proprietary 101787A December 10, 2002 CX77105 Power Amplifier Module for CDMA/AMPS (824–849 MHz) Evaluation Board Description Evaluation Board Description The evaluation board is a platform for testing and interfacing design circuitry. To accommodate the interface testing of the CX77105, the evaluation board schematic and diagrams are included for preliminary analysis and design. Figure 10 shows the basic schematic of the board for the 824 MHz to 849 MHz range. Figure 10. Evaluation Board Schematic VREF 1 VREF C9 1000 pF GND 10 2 VCONT VCONT C3 1000 pF GND 9 RF OUT 3 GND RF OUT 8 RF IN 4 RF IN GND 7 5 VCC1 VCC2 6 VCC1 C6 10 µF C7 0.1 µF C4 1000 pF C5 330 pF VCC2 101787_003 Figure 11. Evaluation Board Assembly Diagram P1 RF IN J1 GND VCC1 GND CELLULAR 4X4 C7 C3 J2 GND VCT U1 C9 C5 C4 C6 VCC2 GND GND VREF EN14-D1235-003 12/17/01 RF OUT P2 101787_002 101787A December 10, 2002 Skyworks Solutions, Inc. Proprietary 11 Package Dimensions and Pin Descriptions CX77105 Power Amplifier Module for CDMA/AMPS (824–849 MHz) Package Dimensions and Pin Descriptions The CX77105 is a multi-layer laminate base, overmold encapsulated modular package designed for surface mount solder attachment to a printed circuit board. Figure 12 is a mechanical drawing of the pad layout for this package. The pin numbering convention starts with pin 1 in the upper left, as indicated in Figure 12, and increments counter-clockwise around the package. Table 6 describes each pin function and Figure 13 illustrates typical case markings. Figure 12. CX77105 Package Dimensional Drawing 1.9 1.275 SOLDER MASK EDGES 1.275 1.0 1.7 0.85 0.4 ± 0.05 0.1 1.9 0.4 ± 0.05 DETAIL PAD METAL PAD EDGES A A R0.2 TOP VIEW Note: Solder mask pattern pad layout as viewed from top looking through package. 0.48 0.45 PIN 1 INDICATOR 10 2 3 4 5 9 8 7 6 4 ± 0.05 TOP VIEW 4 ± 0.05 1.5 ± 0.1 SIDE VIEW All Dimensions in millimeters. 101787_004 12 Skyworks Solutions, Inc. Proprietary 101787A December 10, 2002 CX77105 Power Amplifier Module for CDMA/AMPS (824–849 MHz) Table 6. Pin Descriptions Pin # 1 2 3 4 NOTE(S): (1) (2) Package Dimensions and Pin Descriptions Function VREF VCONT GND RF IN Pin # 5 6 7 8 Function VCC1(1) VCC2(1) GND RF OUT Pin # 9 10 GND PAD(2) Function GND GND GND All supply pins may be connected together at the supply. GROUND PAD is package underside. Figure 13. Typical Case Markings SKYWORKS Mark Pin 1 Identifier CX77105-NN EXXXXX.XX YYWW MEX Manufacturing Part Number-Revision Number Lot Number YY = Manufacture Year WW = Week Package Sealed MEX = Country Code 101787_006 101787A December 10, 2002 Skyworks Solutions, Inc. Proprietary 13 Package and Handling Information CX77105 Power Amplifier Module for CDMA/AMPS (824–849 MHz) Package and Handling Information Because of its sensitivity to moisture absorption, this device package is baked and vacuum packed prior to shipment. Instructions on the shipping container label must be followed regarding exposure to moisture after the container seal is broken, otherwise, problems related to moisture absorption may occur when the part is subjected to high temperature during solder assembly. The CX77105 is capable of withstanding an MSL 3/240 °C solder reflow. Care must be taken when attaching this product, whether it is done manually or in a production solder reflow environment. If the part is attached in a reflow oven, the temperature ramp rate should not exceed 5 °C per second; maximum temperature should not exceed 240 °C. If the part is manually attached, precaution should be taken to insure that the part is not subjected to temperatures exceeding 240 °C for more than 10 seconds. For details on both attachment techniques, precautions, and handling procedures recommended by Skyworks, please refer to Application Note: PCB Design and SMT Assembly/Rework, Document Number 101752. Additional information on standard SMT reflow profiles can also be found in the JEDEC Standard J–STD–020B. Production quantities of this product are shipped in the standard tape-and-reel format. For packaging details, refer to Application Note: Tape and Reel, Document Number 101568. 14 Skyworks Solutions, Inc. Proprietary 101787A December 10, 2002 CX77105 Power Amplifier Module for CDMA/AMPS (824–849 MHz) Electrostatic Discharge Sensitivity Electrostatic Discharge Sensitivity The CX77105 is a Class I device. Figure 14 lists the Electrostatic Discharge (ESD) immunity level for each pin of the CX77105 product. The numbers in Figure 14 specify the ESD threshold level for each pin where the I-V curve between the pin and ground starts to show degradation. The ESD testing was performed in compliance with MIL-STD-883E Method 3015.7 using the Human Body Model. Since 2000 volts represents the maximum measurement limit of the test equipment used, pins marked > 2000 V pass 2000V ESD stress. Figure 14. ESD Sensitivity Ares (Top View) + 1600 V VREF – 1400 V 1 10 GND + 1000 V VCONT – 1300 V 2 9 GND GND 3 8 > + 2000 V RF OUT < – 2000 V + 2000 V – 2000 V RF IN 4 GROUND PAD 7 GND + 2000 V – 2000 V VCC1 5 6 VCC2 > + 2000 V < – 2000 V 101787_007 Various failure criteria can be utilized when performing ESD testing. Many vendors employ relaxed ESD failure standards which fail devices only after “the pin fails the electrical specification limits” or “the pin becomes completely non-functional”. Skyworks employs most stringent criteria, fails devices as soon as the pin begins to show any degradation on a curve tracer. To avoid ESD damage, both latent and visible, it is very important that the product assembly and test areas follow the Class-1 ESD handling precautions listed in Table 7. Table 7. Precautions for GaAs ICs with ESD Thresholds Greater Than 200 V But Less Than 2000 V Personnel Grounding Wrist Straps Conductive Smocks, Gloves and Finger Cots Antistatic ID Badges Protective Workstation Dissipative Table Tops Protective Test Equipment (Properly Grounded) Grounded Tip Soldering Irons Conductive Solder Suckers Static Sensors Facility Relative Humidity Control and Air Ionizers Dissipative Floors (less than 109 Ω to GND) Protective Packaging & Transportation Bags and Pouches (Faraday Shield) Protective Tote Boxes (Conductive Static Shielding) Protective Trays Grounded Carts Protective Work Order Holders 101787A December 10, 2002 Skyworks Solutions, Inc. Proprietary 15 Ordering Information Model Number CX77105 Manufacturing Part Number CX77105-16P Product Revision 16 Package 4x4LM-10 Operating Temperature –30 °C to +85 °C Revision History Revision A Level Date December 10, 2002 Initial Release Description References Application Note: PCB Design and SMT Assembly/Rework, Document Number 101752. Application Note: Tape and Reel, Document Number 101568 JEDEC Standard J–STD–020B. © 2001, 2002, Skyworks Solutions, Inc. All Rights Reserved. Information in this document is provided in connection with Skyworks Solutions, Inc. ("Skyworks") products. These materials are provided by Skyworks as a service to its customers and may be used for informational purposes only. Skyworks assumes no responsibility for errors or omissions in these materials. Skyworks may make changes to its products, specifications and product descriptions at any time, without notice. Skyworks makes no commitment to update the information and shall have no responsibility whatsoever for conflicts, incompatibilities, or other difficulties arising from future changes to its products and product descriptions. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document. Except as may be provided in Skyworks' Terms and Conditions of Sale for such products, Skyworks assumes no liability whatsoever. THESE MATERIALS ARE PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, RELATING TO SALE AND/OR USE OF SKYWORKS™ PRODUCTS INCLUDING WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, PERFORMANCE, QUALITY OR NON-INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. SKYWORKS FURTHER DOES NOT WARRANT THE ACCURACY OR COMPLETENESS OF THE INFORMATION, TEXT, GRAPHICS OR OTHER ITEMS CONTAINED WITHIN THESE MATERIALS. SKYWORKS SHALL NOT BE LIABLE FOR ANY SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION, LOST REVENUES OR LOST PROFITS THAT MAY RESULT FROM THE USE OF THESE MATERIALS. Skyworks™ products are not intended for use in medical, lifesaving or life-sustaining applications. Skyworks' customers using or selling Skyworks™ products for use in such applications do so at their own risk and agree to fully indemnify Skyworks for any damages resulting from such improper use or sale. The following are trademarks of Skyworks Solutions, Inc.: Skyworks™, the Skyworks symbol, and "Breakthrough Simplicity"™. Product names or services listed in this publication are for identification purposes only, and may be trademarks of third parties. Thirdparty brands and names are the property of their respective owners. Additional information, posted at www.skyworksinc.com, is incorporated by reference. General Information: Skyworks Solutions, Inc. 4311 Jamboree Rd. Newport Beach, CA. 92660-3007 www.skyworksinc.com