DATA SHEET
SE2435L: 860 to 930 MHz High-Power RF Front-End Module
Applications
Internet of Things
Smart meters
In-home appliances
Smart thermostats
Industrial applications
Features
Integrated PA with +30 dBm output power
Integrated LNA with programmable bypass
Integrated antenna switching with transmit/receive diversity
function
Low FEM noise figure of 2 dB, typical
Single-ended 50 transmit/receive RF interface
Fast turn-on/turn-off time: < 1 μsec
Supply voltage: 2.0 to 4.8 V
Sleep mode current: < 1 μA
QFN (24-pin, 4 x 4 x 0.9 mm ) NiPdAu plated package
(MSL1, 260 C per JEDEC J-STD-020)
Figure 1. SE2435L Block Diagram
Description
The SE2435L is a high-performance, highly integrated RF
front-end module designed for high-power Industrial, Scientific,
Medical (ISM) band applications operating in the 860 to 930 MHz
frequency range.
The SE2435L is designed for ease of use and maximum flexibility
with fully matched 50 TX and RX inputs and antenna outputs,
and digital controls compatible with 1.6 to 3.6 V CMOS levels.
The RF blocks operate over a wide supply voltage range from 2.0
to 4.8 V allowing the SE2435L to be used in battery powered
applications over a wide spectrum of the battery discharge curve.
The SE2435L is packaged in a 24-pin, 4 x 4 mm Quad Flat NoLead (QFN) package.
A functional block diagram of the SE2435L is provided in Figure 1.
Figure 2 shows the pinout for the SE2435L. Table 1 lists the pin
assignments and signal descriptions.
Figure 2. SE2435L Pinout (Top View)
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
202412K • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • October 2, 2019
1
DATA SHEET • SE2435L: 860 TO 930 MHz HIGH-POWER RF FRONT-END MODULE
Table 1. SE2435L Signal Descriptions
Pin
Name
Description
Pin
Name
Description
1
CSD
Shutdown control input
14
ANT1
Antenna port 1
2
PA_IN
PA input (from Tx filter)
15
N/C
Not connected internally to the device
3
CPS
Rx path select control input
16
TX_IN
Tx signal to antennas (from OMN)
4
CTX
Transmit enable control input
17
N/C
Not connected internally to the device
5
TX_FLT
Transmit signal (to Tx filter)
18
N/C
Not connected internally to the device
6
TR
Bi-directional RF signal to/from transceiver
19
N/C
Not connected internally to the device
7
ANT_SEL
Antenna select control input
20
PA_OUT
PA output (to Z optimum)1
8
GND
Ground
21
VCC2
Positive power supply
9
LNA_IN
LNA input (from Rx filter)
22
N/C
Not connected internally to the device
10
N/C
Not connected internally to the device
23
VCC0
Positive power supply
11
RX_FLT
Rx signal from antennas (to Rx filter)
24
VCC1
Positive power supply
Paddle
GND
Exposed die paddle; electrical and thermal
ground. Connect to PCB ground
12
ANT2
Antenna port 2
13
N/C
Not connected internally to the device
1 Z optimum = 5 Ω for +30 dBm or 8 Ω for +27 dBm POUT.
Electrical and Mechanical Specifications
Table 2 provides the absolute maximum ratings, and Table 3
shows the recommended operating conditions.
Electrical specifications are provided in Tables 4 through 9.
Typical performance characteristics are shown in Figures 3
through 8.
Table 2. SE2435L Absolute Maximum Ratings1
Parameter
Symbol
Minimum
Maximum
Units
Supply voltage (no RF)
VCC
-0.3
5.5
V
Operating temperature
TA
-40
85
°C
Storage temperature
TSTG
-40
125
°C
Tx input power at TR port
PIN_TX_MAX
+10
dBm
Rx input power at ANT1 or ANT2 ports
PIN_RX_MAX
+10
dBm
Electrostatic discharge:
ESD
1000
V
Human Body Model (HBM), Class 1C
1 Exposure to maximum rating conditions for extended periods may reduce device reliability. There is no damage to device with only one parameter set at the limit and all other parameters
set at or below their nominal value. Exceeding any of the limits listed here may result in permanent damage to the device.
ESD HANDLING: Although this device is designed to be as robust as possible, electrostatic discharge (ESD) can damage this device.
This device must be protected at all times from ESD when handling or transporting. Static charges may easily produce
potentials of several kilovolts on the human body or equipment, which can discharge without detection.
Industry-standard ESD handling precautions should be used at all times.
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
2
October 2, 2019 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 202412K
DATA SHEET • SE2435L: 860 TO 930 MHz HIGH-POWER RF FRONT-END MODULE
Table 3. SE2435L Recommended Operating Conditions
Parameter
Symbol
Min
Typ
Max
Units
Supply voltage on VCC
VCC
2.0
4.0
4.8
V
Ambient temperature
TA
-40
+25
+85
°C
Table 4. SE2435L DC Electrical Specifications1
(VCC = 4.0 V, f = 915 MHz, TA = +25 C, Unless Otherwise Noted)
Parameter
Total supply current, transmit mode
Symbol
ICC_TX30
ICC_TX27
ICC_TX24
Test Condition
Min
POUT = +30 dBm
POUT = +27 dBm
POUT = +24 dBm
Typ
Max
Units
550
380
275
Total supply current, receive mode
ICC_RX
Total supply current, receive bypass mode
ICC_RXB
Quiescent current
ICQ_TX
No RF
50
Sleep supply current
ICC_OFF
No RF
0.05
mA
mA
mA
6
mA
μA
280
mA
μA
1.00
1 Performance is guaranteed only under the conditions listed in this table.
Table 5. SE2435L Electrical Specifications: Control Logic Characteristics1
(TA = +25 C, Unless Otherwise Noted)
Parameter
Symbol
Control voltage:
High
Low
VIH
VIL
Input current:
High
Low
IIH
IIL
Test Condition
Min
Typ
1.6
0
Max
Units
Vcc2
0.3
V
V
1
1
μA
μA
1 Performance is guaranteed only under the conditions listed in this table.
2 For Pin 7, ANT_SEL, the maximum is 3.6 V.
Table 6. SE2435L Electrical Specifications: Mode Control Logic (TA = +25) 1
Mode
Sleep (all off)
CPS
CSD
CTX
ANT_SEL
0
0
0
X
Receive or transmit bypass
0
1
0
X
Receive LNA mode
1
1
0
X
Transmit
X
1
1
X
ANT1 port enabled
X
X
X
0
ANT2 port enabled
X
X
X
1
1 “1” = 1.6 to Vcc, “0” = 0 to 0.3 V, “X” = don’t care.
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
202412K • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • October 2, 2019
3
DATA SHEET • SE2435L: 860 TO 930 MHz HIGH-POWER RF FRONT-END MODULE
Table 7. SE2435L Electrical Specifications: AC Transmit Mode
(VCC = 4 V, TA = +25 C, All Unused Ports Terminated at 50 , Unless Otherwise Noted. Input Port TR, Output Ports ANT1 and ANT2
Lumped Elements Filter Connected between the TX_FLT and PA_IN Pins)
Parameter
Frequency range
Symbol
Test Condition
f
Min
Typ
860
Max
Units
930
MHz
POUT_915
VCC = 4.8 V
VCC = 4.0 V
VCC = 3.6 V
VCC = 3.0 V
+31.5
+30.5
+29.5
+28.0
dBm
dBm
dBm
dBm
Output power at ANT1 or ANT2 ports in the
860 to 870 MHz frequency range2
POUT_860
VCC = 4.0 V
VCC = 3.6 V
VCC = 3.0 V
VCC = 2.0 V
+27
+24
+21
+18
dBm
dBm
dBm
dBm
PA power added efficiency
PAE_PA
POUT = +28 dBm at
PA_OUT port, 915 MHz
Small signal gain1
S21_915
900 to 930 MHz
26
dB
Small signal gain2
S21_860
860 to 870 MHz
26
dB
Small signal gain variation1, 2
S21
Gain variation across
frequency range
Output return loss1, 2
S22ANT1,2
Into 50 , ANT1 and
ANT2 ports
2 harmonic1, 3
Output power at ANT1 or ANT2 ports in the
900 to 930 MHz frequency range1
nd
64
-10
%
2
dBp-p
-6
dB
2fo
POUT = +30 dBm
-22
dBc
3 to 10 harmonic1, 3
3fo to 10fo
POUT = +30 dBm
-72
dBc
Turn-on time4
tON
1
μs
Turn-off time
tOFF
1
μs
rd
th
Stability
STAB
CW, PIN = 0 dBm
0.1 GHz to 20 GHz
load VSWR = 6:1
Ruggedness
RU
CW, POUT = +30 dBm into
50 Ω, load VSWR = 10:1
All non-harmonically related outputs less than -43 dBm
No permanent damage
1 900 to 930 MHz with specified matching network on the Evaluation Board.
2 860 to 870 MHz with specified matching network on the Evaluation Board.
3 Measured with continuous wave signal.
4 From 50% of CTX edge to 90% of final RF output power.
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
4
October 2, 2019 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 202412K
DATA SHEET • SE2435L: 860 TO 930 MHz HIGH-POWER RF FRONT-END MODULE
Table 8. SE2435L Electrical Specifications: AC Receive Mode
(VCC = 4 V, TA = +25 C, f = 900 to 930 MHz and 860 to 870 MHz, All Unused Ports Terminated at 50 Ω, Unless Otherwise Noted. Input
Port ANT1 or ANT2, Output Port TR. 0 Ω Connected between the RX_FLT and LNA_IN Pins in lieu of External Filters)
Parameter
Symbol
Test Condition
Min
Frequency range
fIN
860
Receive gain
RX_GAIN
14
Typ
Max
Units
930
MHz
16
18
dB
2
2.5
Receive noise figure
NF
Input third order intercept
IIP3
-5
-2
dBm
Input 1-dB compression point
IP1dB
-15
-12
dBm
Antenna port return loss
S11ANT1,2
Into 50 , ANT1 and
ANT2 ports
-12
dB
-8
dB
Turn-on time1
tON
1
μs
Turn-off time2
tOFF
1
μs
Gain in bypass mode
G_bp
-3
Input 1-dB compression point in bypass mode
IP1dB
+10
-2
dB
dBm
1 From 50% of CTX edge to 90% of final RF output power.
2 From 50% of CTX edge to 10% of final RF output power.
Table 9. SE2435L DC Electrical Specifications: Diversity Antenna Function
(VCC = 4 V, TA = +25 C, f = 900 to 930 MHz and 860 to 870 MHz, All Unused Ports Terminated at 50 , Unless Otherwise Noted)
Parameter
Symbol
Min
Typ
Max
Units
Isolation between ANT1 and ANT2 ports
ISOLANTSW
-20
dB
Insertion loss from TX_IN to ANT1
TX_ANT1
0.8
dB
Insertion loss from TX_IN to ANT2
TX_ANT2
0.8
dB
Insertion loss from ANT1 to RX_FLT
RX_ANT1
0.6
dB
Insertion loss from ANT2 to RX_FLT
RX_ANT2
0.6
dB
Insertion loss from TR to TX_FLT
TxRx_Tx
0.5
dB
ANT1 to ANT2 switching time transmit mode
TANT1-ANT1_TX
800
ns
ANT1 to ANT2 switching time receive mode
TANT1-ANT2_RX
400
ns
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
202412K • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • October 2, 2019
5
DATA SHEET • SE2435L: 860 TO 930 MHz HIGH-POWER RF FRONT-END MODULE
Typical Performance Characteristics1
(VCC = 4 V, TA = +25 C, f = 900 to 930 MHz, All Unused Ports Terminated at 50 , Unless Otherwise Noted)
Figure 3. Typical Harmonics Level at +30 dBm POUT
(including Antenna Filter)
Figure 4. Typical POUT and ICC Transfer Characteristics
Figure 5. Typical Gain vs POUT
(VCC = 4 V)
Figure 6. Typical ICC vs POUT
(VCC = 4 V)
Figure 7. Typical Gain vs POUT
(VCC = 2.0 to 4.8 V)
Figure 8. Typical PAE vs POUT & VCC, CW
(VCC = 2.0 to 4.8 V)
(including OMN and Antenna Filter Losses)
Note 1: Typical performance graphs at 868 MHz are available upon request (+24, +27, and +30 dBm POUT).
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
6
October 2, 2019 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 202412K
DATA SHEET • SE2435L: 860 TO 930 MHz HIGH-POWER RF FRONT-END MODULE
Evaluation Board Description
The SE2435L-EK1 Evaluation is to demonstrate the performance
of the SE2435L Front-End Module. It is optimized for evaluation,
experimentation and investigation, using CW (continuous wave)
signals.
Figure 9 shows the Evaluation Board. The Evaluation Board
schematic diagram is provided in Figure 10. The Bill of Materials
(BOM) for the SE2435L Evaluation Board is listed in Table 10.
Figure 9. SE2435L Evaluation Board
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
202412K • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • October 2, 2019
7
DATA SHEET • SE2435L: 860 TO 930 MHz HIGH-POWER RF FRONT-END MODULE
Figure 10. Evaluation Board Schematic for 915 MHz Application and FCC Conducted Harmonics Rejection Compliant
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
8
October 2, 2019 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 202412K
DATA SHEET • SE2435L: 860 TO 930 MHz HIGH-POWER RF FRONT-END MODULE
Table 10. SE2435L Evaluation Board Bill of Materials1
Component
L2
Part Number
Description
Value
Package
Manufacturer
LQG15HN1N3S02D
High frequency multilayer
1.3 nH
0402
muRata
C17
GRM1555C1H1R8CZ01
Multilayer ceramic
1.8 pF
0402
muRata
C11
GRM155R71H102KA01
Multilayer ceramic
1 nF
0402
muRata
L1
LQG15HN3N0S02D
High frequency multilayer
3.0 nH
0402
muRata
L4
LQG15HN3N3S02D
High frequency multilayer
3.3 nH
0402
muRata
L3
LQG15HN4N7S02D
High frequency multilayer
4.7 F
0402
muRata
C6
GRM188R60J475KE19
Multilayer ceramic
4.7 F
0603
muRata
C3
GRM1555C1H8R2DZ01
Multilayer ceramic
8.2 pF
0402
muRata
C1
GRM155R71E103KA01
Multilayer ceramic
10 nF
0402
muRata
J4
TSW-110-07-G-D
100 mil Header
10X2
100 mil
Samtec
C2
GRM1555C1H220JZ01
Multilayer ceramic
22 pF
0402
muRata
C8
GRM1555C1H330JZ01
Multilayer ceramic
33 pF
0402
muRata
C10
GRM1555C1H101JZ01
Multilayer ceramic
100 pF
0402
muRata
U1
SE2435L
860 to 930 MHz high power RF FEM
SE2435L
QFN400x400
Skyworks
J1, J2, J3
142-0701-851
SMA end launch straight jack receptacle - tab contact
SMA
End launch
Johnson Components
C9, C12, C13, R1
GRM1555C1H3R3CZ01
Multilayer ceramic
3.3 pF
0402
muRata
L5, L6 ,L7, L8, L9
LQG18HN6N8S00D
High frequency multilayer
6.8 nH
0603
muRata
1 Schematic and BOM has been designed to optimize performance with CW signals, 100% duty cycle.
Evaluation Board Setup Procedure
This section provides the details required to setup the evaluation
board and the test equipment for the SE2435L. Table 11
describes the pins on the Power and Control I/O Header J4. Note
that it is recommended to use proper engineering connection
practices by making RF and digital connections prior to turning on
the power supply.
Connect Supply
1. Connect (J1, J2, and J3) to 50 instruments. Terminate all
unused ports (if applicable) with 50 .
2. Connect the supply ground to Pin 1 of J4.
3. Connect 3.6 V or 4.0 V to Pin 2 of J4:
The required RF path/antenna can be selected using the
information in Table 6.
Measure Performance
TX: The 860 to 930 MHz (depending on the region) amplifier
performance can be monitored by applying an RF signal to
connector J1 (TR), and monitoring the output power on
connector J2 (ANT2) or J3 (ANT1).
RX: The 860 to 930 MHz LNA performance can be monitored by
applying an RF signal to connector J2 (ANT2) or J3 (ANT1), and
monitoring the output signal on connector J1 (TR).
CAUTION Be careful not to overdrive the amplifier by applying
too much RF on the input to the device. A starting
input power of -20 dBm is suitable.
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
202412K • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • October 2, 2019
9
DATA SHEET • SE2435L: 860 TO 930 MHz HIGH-POWER RF FRONT-END MODULE
Table 11. Power and Control I/O Header (J4)
Evaluation Board Label
Pin Number
Description
Recommended setting
GND
1,3,5,7,9,11,13,15,17,19
Ground
General purpose grounds
VCC
2,4,6,10,14,18
Supply voltage
General purpose VCC provided as the main power supply.
CTX
8
Control
CPS
12
Control
CSD
16
Control
ANTSEL
20
Control
See Table 6.
Package Dimensions
Package and Handling Information
The layout footprint for the SE2435L is provided in Figure 11.
Typical part markings are shown in Figure 12. Package
dimensions for the SE2435L are shown in Figure 13, and tape and
reel dimensions are provided in Figure 14.
Instructions on the shipping container label regarding exposure to
moisture after the container seal is broken must be followed.
Otherwise, problems related to moisture absorption may occur
when the part is subjected to high temperature during solder
assembly.
The SE2435L is rated to Moisture Sensitivity Level 1 (MSL1) at
260 C. It can be used for lead or lead-free soldering. For
additional information, refer to the Skyworks Application Note,
Solder Reflow Information, document number 200164.
Care must be taken when attaching this product, whether it is
done manually or in a production solder reflow environment.
Production quantities of this product are shipped in a standard
tape and reel format.
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
10
October 2, 2019 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 202412K
DATA SHEET • SE2435L: 860 TO 930 MHZ HIGH-POWER RF FRONT-END MODULE
Figure 11. SE2435L Recommended Footprint
(Top View)
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
11
October 2, 2019 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 202412K
DATA SHEET • SE2435L: 860 TO 930 MHz HIGH-POWER RF FRONT-END MODULE
Figure 12. Typical Part Markings
(Top View)
Figure 13. SE2435L Package Dimensions
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
12
October 2, 2019 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 202412K
DATA SHEET • SE2435L: 860 TO 930 MHz HIGH-POWER RF FRONT-END MODULE
Figure 14. SE2435L Tape and Reel Dimensions
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
202412K • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • October 2, 2019
13
DATA SHEET • SE2435L: 860 TO 930 MHz HIGH-POWER RF FRONT-END MODULE
Ordering Information
Model Name
Manufacturing Part Number
Evaluation Board Part Number
SE2435L: FCC +30 dBm 900 to 930 MHz Front-End Module
SE2435L
SE2435L-EK1
SE2435L: ETSI +27 dBm 868 to 880 MHz Front-End Module
SE2435L
SE2435L-EK2
SE2435L: ETSI + FCC +30 dBm 868 to 930 MHz Front-End Module
SE2435L
SE2435L-EK5
SE2435L: FCC +25 dBm 915 MHz Front-End Module
SE2435L
SE2435L-EK7
Copyright © 2013-2016, 2019 Skyworks Solutions, Inc. All Rights Reserved.
Information in this document is provided in connection with Skyworks Solutions, Inc. (“Skyworks”) products or services. These materials, including the information contained herein, are provided by
Skyworks as a service to its customers and may be used for informational purposes only by the customer. Skyworks assumes no responsibility for errors or omissions in these materials or the
information contained herein. Skyworks may change its documentation, products, services, specifications or product descriptions at any time, without notice. Skyworks makes no commitment to
update the materials or information and shall have no responsibility whatsoever for conflicts, incompatibilities, or other difficulties arising from any future changes.
No license, whether express, implied, by estoppel or otherwise, is granted to any intellectual property rights by this document. Skyworks assumes no liability for any materials, products or
information provided hereunder, including the sale, distribution, reproduction or use of Skyworks products, information or materials, except as may be provided in Skyworks Terms and Conditions
of Sale.
THE MATERIALS, PRODUCTS AND INFORMATION ARE PROVIDED “AS IS” WITHOUT WARRANTY OF ANY KIND, WHETHER EXPRESS, IMPLIED, STATUTORY, OR OTHERWISE, INCLUDING FITNESS FOR A
PARTICULAR PURPOSE OR USE, MERCHANTABILITY, PERFORMANCE, QUALITY OR NON-INFRINGEMENT OF ANY INTELLECTUAL PROPERTY RIGHT; ALL SUCH WARRANTIES ARE HEREBY EXPRESSLY
DISCLAIMED. SKYWORKS DOES NOT WARRANT THE ACCURACY OR COMPLETENESS OF THE INFORMATION, TEXT, GRAPHICS OR OTHER ITEMS CONTAINED WITHIN THESE MATERIALS. SKYWORKS
SHALL NOT BE LIABLE FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO ANY SPECIAL, INDIRECT, INCIDENTAL, STATUTORY, OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION,
LOST REVENUES OR LOST PROFITS THAT MAY RESULT FROM THE USE OF THE MATERIALS OR INFORMATION, WHETHER OR NOT THE RECIPIENT OF MATERIALS HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGE.
Skyworks products are not intended for use in medical, lifesaving or life-sustaining applications, or other equipment in which the failure of the Skyworks products could lead to personal injury,
death, physical or environmental damage. Skyworks customers using or selling Skyworks products for use in such applications do so at their own risk and agree to fully indemnify Skyworks for any
damages resulting from such improper use or sale.
Customers are responsible for their products and applications using Skyworks products, which may deviate from published specifications as a result of design defects, errors, or operation of
products outside of published parameters or design specifications. Customers should include design and operating safeguards to minimize these and other risks. Skyworks assumes no liability for
applications assistance, customer product design, or damage to any equipment resulting from the use of Skyworks products outside of stated published specifications or parameters.
Skyworks and the Skyworks symbol are trademarks or registered trademarks of Skyworks Solutions, Inc. or its subsidiaries in the United States and other countries. Third-party brands and names
are for identification purposes only, and are the property of their respective owners. Additional information, including relevant terms and conditions, posted at www.skyworksinc.com, are
incorporated by reference.
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
14
October 2, 2019 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 202412K
