SKY13397-388LF

DATA SHEET SKY13397-388LF: 0.1 – 3.0 GHz DP5T Switch Applications • WCDMA distribution band switches • Broadband, high power switches • Antenna tuning switches Features • Broadband frequency range: 0.1 to 3.0 GHz • High IP0.1dB: +38 dBm • Low insertion loss: 0.35 dB @ 1.0 GHz and 0.4 dB @ 2.0 GHz • High isolation: >30 dB @ 1.0 GHz and 2.0 GHz • Operating battery voltage range: 2.5 to 5.0 V • Small, QFN (16-pin, 2.3 x 2.3 mm) package (MSL1, 260 °C per JEDEC J-STD-020) Figure 1. SKY13397-388LF Block Diagram Description The SKY13397-388LF is a double-pole, five-throw (DP5T) switch designed for broadband, high-power switching applications that demand low harmonics and low insertion loss. The switch is optimized for 3G WCDMA applications. The SKY13397-388LF features integrated logic that uses only two control lines for switch operation. The low current consumption of the device makes it very suitable for battery-operated applications. The switch is manufactured using a state of the art Silicon on Insulator (SOI) process, and is provided in a compact Quad Flat No-Lead (QFN) 2.3 x 2.3 mm package. A functional block diagram is shown in Figure 1. The pin configuration and package are shown in Figure 2. Signal pin assignments and functional pin descriptions are provided in Table 1. Figure 2. SKY13397-388LF Pinout – 16-Pin QFN (Top View) Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 201544E • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • January 4, 2013 1 DATA SHEET • SKY13397-388LF DP5T SWITCH Table 1. SKY13397-388LF Signal Descriptions Pin # Name Description Pin # Name Description 1 GND Ground 9 GND Ground 2 IN2 RF input 2. This pin connected to pins 5, 7, or 10 depending on the control voltage applied to pins 15 and 16. 10 OUT2C RF input 2C, connected to RF input 2 3 GND Ground 11 OUT1B RF output 1B, connected to RF input 1 4 IN1 RF input 1. This pin connected to pins pins 11 or 12 depending on the control voltage applied to pins 15 and 16. 12 OUT1A RF output 1A, connected to RF input 1 5 OUT2A RF output 2A, connected to RF input 2 13 GND Ground 6 GND Ground 14 VDD Supply voltage input. 7 OUT2B RFoutput 2B, connected to RF input 2 15 GPIO2 Control signal 2. Logic level applied to this pin and to pin 16, controls the state of the switch. 8 GND Ground 16 GPIO1 Control signal 1. Logic level applied to this pin and to pin 15, controls the state of the switch. Table 2. SKY13397-388LF Absolute Maximum Ratings Parameter Symbol Minimum Maximum Units V Supply voltage VDD 2.5 5.5 Control voltage VCTL 1.65 3.30 V Input power PIN +40 dBm Storage temperature TSTG –50 +100 °C Operating temperature TOP –30 +85 °C Note: Exposure to maximum rating conditions for extended periods may reduce device reliability. There is no damage to device with only one parameter set at the limit and all other parameters set at or below their nominal value. Exceeding any of the limits listed here may result in permanent damage to the device. CAUTION: Although this device is designed to be as robust as possible, Electrostatic Discharge (ESD) can damage this device. This device must be protected at all times from ESD. Static charges may easily produce potentials of several kilovolts on the human body or equipment, which can discharge without detection. Industry-standard ESD precautions should be used at all times. Functional Description The SKY13397-388LF includes an internal negative voltage generator and decoder that eliminate the need for external DC blocking capacitors on the RF ports. No external components are required for proper operation. DC decoupling capacitors may be added on the VDD and control lines if necessary. Switching is controlled by two control voltage inputs, GPIO1 and GPIO2. Depending on the logic voltage level applied to the control pins, the OUT1 signal (pin 4) is connected to one of two switched RF inputs (IN1A or IN1B) through a low insertion loss path, while the OUT2 signal (pin 2) is simultaneously switched to one of three RF inputs (IN2A, IN2B, IN2C). For proper switching operation, the SKY13397-388LF must be set to a state for a minimum of 10 μs before changing to a different state. Shutdown mode is enabled by connecting both control pins to logic low. This mode reduces the overall current consumption of the device to 5 μA, typical. To prevent the switch from accidentally entering shutdown mode during switching, caution must be taken to avoid having both control signals (GPIO1 and GPIO2) set to logic low for more than 500 ns. When exiting shutdown mode, the switch has a 25 μs startup time before switching occurs. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 2 January 4, 2013 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 201544E DATA SHEET • SKY13397-388LF DP5T SWITCH Electrical and Mechanical Specifications I/O (GPIO) pins 15 and 16 with VDD = high. When VDD is high, the switch is active and its state is controlled as described in Table 4. When the switch is in standby mode, all paths are not operating. The absolute maximum ratings of the SKY13397-388LF are provided in Table 2. Electrical specifications are provided in Table 3. The SKY13397-388LF may be used in one of two modes: active and standby. These modes are controlled by the General Purpose Table 3. SKY13397-388LF Electrical Specifications (Note 1) (VDD = 2.5 V to 5.0 V, TOP = +25 °C, VHIGH > 1.8 V, All Unused RF Ports Terminated in a 50 Ω Load, Unless Otherwise Noted) Parameter Symbol Test Condition Min Typical Max Units 0.35 0.40 0.45 0.45 0.50 0.60 dB dB dB Insertion loss 0.1 to 1.0 GHz 1.0 to 2.0 GHz 2.0 to 2.5 GHz Isolation 0.1 to 1.0 GHz 1.0 to 2.0 GHz 2.0 to 2.5 GHz 40 28 27 51 31 29 dB dB dB Return loss 0.1 to 2.2 GHz 14 17 dB fFUNDAMENTAL = 900 MHz, PIN = +28 dBm –56 dBm fFUNDAMENTAL = 1800 MHz, PIN = +28 dBm –51 dBm fFUNDAMENTAL = 900 MHz, PIN = +28 dBm –52 dBm fFUNDAMENTAL = 1800 MHz, PIN = +28 dBm –45 nd 2 harmonic 2fo rd 3 harmonic 3fo Input 0.1 dB compression point Supply voltage IP0.1dB f = 900 MHz +37 +38 f = 1800 MHz +37 +38 VDD Control voltage (Note 2) Supply Current Switching rise time 2.5 VHIGH 1.65 dBm dBm dBm 5.0 V 2.00 3.30 V VLOW 0 0.30 V Control current in active & isolation 27 μA Control current in standby @ VDD = 2.5 V 0.8 Control current in standby @ VDD = 4.5 V 4.7 μA Control current in standby @ VDD = 5.5 V 6.0 μA 10/90% RF 0.40 5.0 0.75 μA μs Switching fall time 90/10% RF 1.0 1.5 μs Switching on time 50% VCTL to 10/90% RF 2.2 2.5 μs Switching off time 50% VCTL to 90/10% RF 2.2 2.5 μs Logic dwell time (Note 3) TOP = –40 °C to +85 °C Startup time (Note 4) Shutdown state to any RF switch state 10 μs 12 20 25 μs Note 1: Performance is guaranteed only under the conditions listed in this Table. Note 2: Control voltage must be less than or equal to VDD at all times. Note 3: Dwell time refers to the amount of time the switch is required to stay in any one state before switching to another state. Refer to the Functional Description section for more information. Note 4: Startup time refers to the amount of time it takes for the switch to be fully operational when coming out of shutdown mode. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 201544E • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • January 4, 2013 3 DATA SHEET • SKY13397-388LF DP5T SWITCH Table 4. SKY13397-388LF Truth Table Note: State GPIO1 GPIO2 RF Path 1 0 0 Standby 2 0 1 OUT1B, OUT2B 3 1 0 OUT1A, OUT2A 4 1 1 OUT2C “1” = +1.65 to +3.30 V (for GPIO1 and GPIO2 pins). “0” = 0 V to +0.2 V. Any state other than described in this Table places the switch into an undefined state. An undefined state will not damage the device. Evaluation Board Package and Handling Information The SKY13397-388LF Evaluation Board is used to test the performance of the SKY13397-388LF DP6T Switch. An Evaluation Board schematic diagram is provided in Figure 3. An assembly drawing for the Evaluation Board is shown in Figure 4. Instructions on the shipping container label regarding exposure to moisture after the container seal is broken must be followed. Otherwise, problems related to moisture absorption may occur when the part is subjected to high temperature during solder assembly. Package Dimensions The PCB layout footprint for the SKY13397-388LF is provided in Figure 5. Typical case markings are shown in Figure 6. Package dimensions for the 16-pin QFN are shown in Figure 7, and tape and reel dimensions are provided in Figure 8. THE SKY13397-388LF is rated to Moisture Sensitivity Level 1 (MSL1) at 260 °C. It can be used for lead or lead-free soldering. For additional information, refer to the Skyworks Application Note, Solder Reflow Information, document number 200164. Care must be taken when attaching this product, whether it is done manually or in a production solder reflow environment. Production quantities of this product are shipped in a standard tape and reel format. Figure 3. SKY13397-388LF Evaluation Board Schematic Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 4 January 4, 2013 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 201544E DATA SHEET • SKY13397-388LF DP5T SWITCH Figure 4. SKY13397-388LF Evaluation Board Assembly Diagram Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 201544E • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • January 4, 2013 5 DATA SHEET • SKY13397-388LF DP5T SWITCH Figure 5. SKY13397-388LF PCB Layout Footprint (Top View) Figure 6. Typical Case Markings (Top View) Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 6 January 4, 2013 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 201544E DATA SHEET • SKY13397-388LF DP5T SWITCH Figure 7. SKY13397-388LF 16-Pin QFN Package Dimensions Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 201544E • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • January 4, 2013 7 DATA SHEET • SKY13397-388LF DP5T SWITCH Figure 8. SKY13397-388LF Tape and Reel Dimensions Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 8 January 4, 2013 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 201544E DATA SHEET • SKY13397-388LF DP5T SWITCH Ordering Information Model Name SKY13397-388LF DP5T Switch Manufacturing Part Number SKY13397-388LF Evaluation Board Part Number SK41602-1 Copyright © 2011, 2013 Skyworks Solutions, Inc. All Rights Reserved. Information in this document is provided in connection with Skyworks Solutions, Inc. (“Skyworks”) products or services. These materials, including the information contained herein, are provided by Skyworks as a service to its customers and may be used for informational purposes only by the customer. Skyworks assumes no responsibility for errors or omissions in these materials or the information contained herein. Skyworks may change its documentation, products, services, specifications or product descriptions at any time, without notice. Skyworks makes no commitment to update the materials or information and shall have no responsibility whatsoever for conflicts, incompatibilities, or other difficulties arising from any future changes. No license, whether express, implied, by estoppel or otherwise, is granted to any intellectual property rights by this document. Skyworks assumes no liability for any materials, products or information provided hereunder, including the sale, distribution, reproduction or use of Skyworks products, information or materials, except as may be provided in Skyworks Terms and Conditions of Sale. THE MATERIALS, PRODUCTS AND INFORMATION ARE PROVIDED “AS IS” WITHOUT WARRANTY OF ANY KIND, WHETHER EXPRESS, IMPLIED, STATUTORY, OR OTHERWISE, INCLUDING FITNESS FOR A PARTICULAR PURPOSE OR USE, MERCHANTABILITY, PERFORMANCE, QUALITY OR NON-INFRINGEMENT OF ANY INTELLECTUAL PROPERTY RIGHT; ALL SUCH WARRANTIES ARE HEREBY EXPRESSLY DISCLAIMED. SKYWORKS DOES NOT WARRANT THE ACCURACY OR COMPLETENESS OF THE INFORMATION, TEXT, GRAPHICS OR OTHER ITEMS CONTAINED WITHIN THESE MATERIALS. SKYWORKS SHALL NOT BE LIABLE FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO ANY SPECIAL, INDIRECT, INCIDENTAL, STATUTORY, OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION, LOST REVENUES OR LOST PROFITS THAT MAY RESULT FROM THE USE OF THE MATERIALS OR INFORMATION, WHETHER OR NOT THE RECIPIENT OF MATERIALS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Skyworks products are not intended for use in medical, lifesaving or life-sustaining applications, or other equipment in which the failure of the Skyworks products could lead to personal injury, death, physical or environmental damage. Skyworks customers using or selling Skyworks products for use in such applications do so at their own risk and agree to fully indemnify Skyworks for any damages resulting from such improper use or sale. Customers are responsible for their products and applications using Skyworks products, which may deviate from published specifications as a result of design defects, errors, or operation of products outside of published parameters or design specifications. Customers should include design and operating safeguards to minimize these and other risks. Skyworks assumes no liability for applications assistance, customer product design, or damage to any equipment resulting from the use of Skyworks products outside of stated published specifications or parameters. Skyworks, the Skyworks symbol, and “Breakthrough Simplicity” are trademarks or registered trademarks of Skyworks Solutions, Inc., in the United States and other countries. Third-party brands and names are for identification purposes only, and are the property of their respective owners. Additional information, including relevant terms and conditions, posted at www.skyworksinc.com, are incorporated by reference. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 201544E • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • January 4, 2013 9