SKY13414-485LF

DATA SHEET SKY13414-485LF: 0.1 to 3.8 GHz SP4T Antenna Switch Applications  Any 2G/3G/4G antenna diversity or LTE (TDD/FDD) transmit/receive system for which GSM transmit is not required RF1 Features RF2  Broadband frequency range: 0.1 to 3.8 GHz  Low insertion loss: 0.45 dB typical @ 2.7 GHz RF3  High isolation: >31 dB @ 2.7 GHz RF4 ANT  Internal 50 Ω port to control diversity antenna impedance when device is not in use Skyworks Green™ products are compliant with all applicable legislation and are halogen-free. For additional information, refer to Skyworks Definition of Green™, document number SQ04-0074. V1 V2 Decoder V3 Bias VDD  Small QFN (14-pin, 2.0 x 2.0 mm) package (MSL1, 260 C per JEDEC J-STD-020) 201689-001 50 Ω  Integrated logic Figure 1. SKY13414-485LF Block Diagram Description The SKY13414-485LF is a single pole, four-throw (SP4T) antenna switch with an internal 50 Ω termination. The high-linearity performance and low insertion loss achieved by the SKY13414-485LF make it an ideal choice for main/diversity switching commonly used in LTE-based handsets, data cards, and tablets that use antenna diversity solutions. The SKY13414-485LF is part of a scalable family of products that covers SP4T through SP8T switches that allow up to eight bands of WCDMA/LTE:  SKY13414-485LF SP4T Antenna Switch (this Data Sheet)  SKY13415-485LF SP5T Antenna Switch (Data Sheet #201704)  SKY13416-485LF SP6T Antenna Switch (Data Sheet #201679)  SKY13417-485LF SP7T Antenna Switch (Data Sheet #201661)  SKY13418-485LF SP8T Antenna Switch (Data Sheet #201712) Switching is controlled by three CMOS/TTL-compatible control voltage inputs (V1, V2, and V3). Depending on the logic voltage level applied to the control pins, the ANT pin is connected to one of four switched RF outputs (RF1 to RF4) using a low insertion loss path, while the paths between the ANT pin and the other RF pins are in a high isolation state. The antenna path can also be closed on a 50 Ω load when it needs to be terminated. The 50 Ω load is internally grounded. No external blocking capacitors are required on the RF paths unless VDC is externally applied. The SKY13414-485LF is manufactured in a compact, 14-pin 2.0 x 2.0 mm, Quad Flat No-Lead (QFN) package. A functional block diagram is shown in Figure 1. The pin configuration and package are shown in Figure 2. Signal pin assignments and functional pin descriptions are provided in Table 1. The symmetric port designs provide flexibility in signal routing for both receive diversity and higher power TD-SCDMA/TDD-LTE, WCDMA/FDD, and LTE transmit/receive applications. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 201689J • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • November 23, 2016 1 N/C ANT N/C DATA SHEET • SKY13414-485LF: SP4T ANTENNA SWITCH 14 13 12 RF3 2 10 RF4 RF1 3 9 RF2 VDD 4 8 N/C 5 6 7 V1 N/C V2 11 V3 N/C 1 201689-002 Figure 2. SKY13414-485LF Pinout (Top View) Table 1. SKY13414-485LF Signal Descriptions1 Pin Name Description Pin 8 Name N/C Description 1 N/C Not connected Not connected 2 RF3 RF I/O path 3 9 RF2 RF I/O path 2 3 RF1 RF I/O path 1 10 RF4 RF I/O path 4 4 VDD DC power supply 11 N/C Not connected 5 V3 DC control voltage 3 12 N/C Not connected 6 V2 DC control voltage 2 13 ANT Antenna port 7 V1 DC control voltage 1 14 N/C Not connected 1 Bottom ground paddles must be connected to ground. Functional Description Electrical and Mechanical Specifications The SKY13414-485LF includes an internal negative voltage generator and decoder that eliminate the need for external DC blocking capacitors on the RF ports. No external components are required for proper operation. DC decoupling capacitors may be added on the VDD and control lines if necessary. The absolute maximum ratings of the SKY13414-485LF are provided in Table 2. Electrical specifications are provided in Table 3. Switching is controlled by three control voltage inputs, V1, V2, and V3. Depending on the logic voltage level applied to the control pins, the antenna pin is connected to one of four switched RF outputs or a 50 Ω termination. The state of the SKY13414-485LF is determined by the logic shown in Table 4. The isolation matrix shown in Table 5 provides the port-to-port and antenna-to-port isolation for all available RF states at four different frequencies: 1.0 GHz, 2.0 GHz, 2.7 GHz, and 3.8 GHz. Shutdown mode is enabled by connecting all three control pins (V1, V2, and V3) to logic high. This mode reduces the overall current consumption of the device to 5 μA typical. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 2 November 23, 2016 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 201689J DATA SHEET • SKY13414-485LF: SP4T ANTENNA SWITCH Table 2. SKY13414-485LF Absolute Maximum Ratings1 Parameter Minimum Maximum Units VDD 2.5 5.0 V Control voltage (V1, V2, and V3) VCTL –0.5 +3.0 V RF power applied to “on” arm (RF1 to RF4) or ANT port: PIN +37.5 +35 dBm dBm Supply voltage Symbol 0.1 to 2.7 GHz (RF1 to RF4 arm) 3.4 to 3.8 GHz (RF2 to RF4 arm) RF power applied to “off” arm (RF1 to RF4) PIN +33 dBm RF power applied to antenna in the 50 Ω switched RF output state PIN +27 dBm Operating temperature TOP –40 +85 C Storage temperature TSTG –55 +150 C Electrostatic discharge: ESD 500 V Human Body Model (HBM) 1 Exposure to maximum rating conditions for extended periods may reduce device reliability. There is no damage to device with only one parameter set at the limit and all other parameters set at or below their nominal value. Exceeding any of the limits listed here may result in permanent damage to the device. ESD HANDLING: Although this device is designed to be as robust as possible, electrostatic discharge (ESD) can damage this device. This device must be protected at all times from ESD when handling or transporting. Static charges may easily produce potentials of several kilovolts on the human body or equipment, which can discharge without detection. Industry-standard ESD handling precautions should be used at all times. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 201689J • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • November 17, 2016 3 DATA SHEET • SKY13414-485LF: SP4T ANTENNA SWITCH Table 3. SKY13414-485LF General Electrical Specifications1 (VDD = 2.6 V, V1 = V2 = V3 = 0/1.8 V, PIN = 0 dBm, TOP = +25 C, Characteristic Impedance [ZO] = 50 Ω, Unless Otherwise Noted) Parameter Symbol Test Condition (Note 2) Min Typical Max Units 2.5 3.0 4.8 V 40 50 μA 1.80 2.70 0.4 V V 0.5 1.0 μA DC Specifications Supply voltage VDD Supply current IDD Control voltage: High Low VCTL_H VCTL_L Control current ICTL Shutdown mode supply current 1.35 VCTL = 1.8 V IOFF V1/2/3 = 1.8 V, VDD = 3 V 5 10 μA tON 50% of control voltage to 90% of final RF power, switching between RF1/2/3/4/5/6 1.75 2.20 μs IL 0.1 to 1.0 GHz 1.0 to 2.0 GHz 2.0 to 2.7 GHz 3.4 to 3.8 GHz 0.40 0.40 0.45 0.6 0.50 0.50 0.60 0.8 dB dB dB dB Iso 0.1 to 1.0 GHz 1.0 to 2.0 GHz 2.0 to 2.7 GHz 3.4 to 3.8 GHz 38 32 27 20 42 35 31 26 dB dB dB dB RL 0.1 to 1.0 GHz 1.0 to 2.0 GHz 2.0 to 2.7 GHz 3.4 to 3.8 GHz 21 23 15 12 24 25 18 15 dB dB dB dB 2fo PIN = +26 dBm, 0.1 to 3.0 GHz +99 dBc 3fo PIN = +26 dBm, 0.1 to 3.0 GHz +105 dBc 2fo PIN = +26 dBm, 3.4 to 3.8 GHz, VSWR = 1:1 –55 dBm 3fo PIN = +26 dBm, 3.4 to 3.8 GHz, VSWR = 1:1 –65 dBm 2fo PIN = +26 dBm, 3.4 to 3.8 GHz, VSWR = 5:1 –50 dBm 3fo PIN = +26 dBm, 3.4 to 3.8 GHz, VSWR = 5:1 –60 dBm +37.5 +37 dBm dBm +70 dBm Turn-on switching time RF Specifications Insertion loss (ANT pin to RF1/2/3/4 pins) Isolation (ANT pin to RF1/2/3/4 pins) Input return loss (ANT pin to RF1/2/3/4 pins) Second harmonics (ANT pin to RF1/2/3/4 pins) Third harmonics (ANT pin to RF1/2/3/4 pins) Harmonics (ANT to RF2, 3, 4) Harmonics (ANT to RF2, 3, 4) Harmonics (ANT to RF2, 3, 4) Harmonics (ANT to RF2, 3, 4) 0.1 dB compression point (ANT pin to RF2/3/4 pins) Third order input intercept point 50 Ω power handling P0.1dB 0.8 GHz to 3.0 GHz 3.4 to 3.8 GHz IIP3 @ 2.0 GHz, PIN = +26 dBm, Δf = 1 MHz @ 0.1 to 3.8 GHz +27 Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 4 November 23, 2016 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 201689J dBm DATA SHEET • SKY13414-485LF: SP4T ANTENNA SWITCH Table 4. SKY13414-485LF Control Logic1 Control Pins V1 (Pin 7) V2 (Pin 6) Switched RF Outputs V3 (Pin 5) RF1 (Pin 3) RF2 (Pin 9) RF3 (Pin 2) RF4 (Pin 10) 50 Ω 0 0 0 Insertion Loss Isolation Isolation Isolation Isolation 0 0 1 Isolation Insertion Loss Isolation Isolation Isolation 0 1 0 Isolation Isolation Insertion Loss Isolation Isolation 0 1 1 Isolation Isolation Isolation Insertion Loss Isolation 1 0 0 Isolation Isolation Isolation Isolation Isolation 1 0 1 Isolation Isolation Isolation Isolation 50 Ω 1 1 1 Shutdown mode 1 “High” = 1.8 V; “Low” = 0 V. Any state other than that described in this table places the switch into an undefined state. An undefined state will not damage the device. Table 5. Isolation Matrix (1 of 2) Frequency (GHz) “On” Port Isolation (dB) RF1 RF2 RF3 RF4 Antenna-to-Port RF1 1.0 – –47 –40 –42 RF1 2.0 – –39 –31 –35 RF1 2.7 – –36 –27 –32 RF1 3.8 – –31 –22 –27 RF2 1.0 –46 – –40 –40 RF2 2.0 –38 – –34 –32 RF2 2.7 –35 – –31 –28 RF2 3.8 –30 – –26 –23 RF3 1.0 –38 –46 – –42 RF3 2.0 –30 –39 – –35 RF3 2.7 –27 –36 – –32 RF3 3.8 –23 –31 – –27 RF4 1.0 –45 –38 –41 – RF4 2.0 –38 –31 –34 – RF4 2.7 –34 –28 –31 – RF4 3.8 –30 –24 –26 – Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 201689J • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • November 17, 2016 5 DATA SHEET • SKY13414-485LF: SP4T ANTENNA SWITCH Table 5. Isolation Matrix (2 of 2) Frequency (GHz) “On” Port Isolation (dB) RF1 RF2 RF3 RF4 Port-to-Port RF1 1.0 – –54 –31 –52 RF1 2.0 – –43 –25 –43 RF1 2.7 – –39 –22 –39 RF1 3.8 – –32 –17 –34 RF2 1.0 –55 – –48 –31 RF2 2.0 –43 – –41 –24 RF2 2.7 –38 – –37 –21 RF2 3.8 –32 – –33 –17 RF3 1.0 –30 –56 – –52 RF3 2.0 –24 –45 – –43 RF3 2.7 –21 –40 – –39 RF3 3.8 –17 –34 – –34 RF4 1.0 –56 –30 –48 – RF4 2.0 –44 –24 –41 – RF4 2.7 –39 –21 –37 – RF4 3.8 –32 –17 –32 – Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 6 November 23, 2016 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 201689J DATA SHEET • SKY13414-485LF: SP4T ANTENNA SWITCH Evaluation Board Description Package and Handling Information The SKY13414-485LF Evaluation Board is used to test the performance of the SKY13414-485LF SP4T switch. An Evaluation Board schematic diagram is provided in Figure 3. An assembly drawing for the Evaluation Board is shown in Figure 4. Instructions on the shipping container label regarding exposure to moisture after the container seal is broken must be followed. Otherwise, problems related to moisture absorption may occur when the part is subjected to high temperature during solder assembly. Package Dimensions The SKY13414-485LF is rated to Moisture Sensitivity Level 1 (MSL1) at 260 C. It can be used for lead or lead-free soldering. For additional information, refer to the Skyworks Application Note, Solder Reflow Information, document number 200164. The PCB layout footprint for the SKY13414-485LF is provided in Figure 5. Typical part markings are shown in Figure 6. Package dimensions are shown in Figure 7, and tape and reel dimensions are provided in Figure 8. Care must be taken when attaching this product, whether it is done manually or in a production solder reflow environment. Production quantities of this product are shipped in a standard tape and reel format. × RF Output Port 3 RF Output Port 1 N/C 1 12 ANT × 13 N/C 14 Antenna × N/C N/C 2 RF3 RF4 RF1 RF2 VDD N/C 3 5 × V1 V2 6 RF Output Port 4 RF Output Port 2 9 8 V3 DC Control Voltage 3 DC Control Voltage 2 × 10 4 DC Power 11 7 DC Control Voltage 1 201689-003 Figure 3. SKY13414-485LF Evaluation Board Schematic Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 201689J • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • November 17, 2016 7 DATA SHEET • SKY13414-485LF: SP4T ANTENNA SWITCH RF3 RF1 N/C N/C GND VDD V3 V2 V1 N/C ANT N/C RF2 RF4 N/C 201689-004 Figure 4. SKY13414-485LF Evaluation Board Assembly Diagram 14X 0.755 Pin 14 14X 0.395 R0.125 Pin 1 Indicator Pin 1 14X 0.200 6X 0.450 Pitch 2X 0.500 Exposed Soldering Area Package Outline 4X 0.400 Pitch 2X 0.500 201689-005 All measurements in millimeters Figure 5. SKY13414-485LF PCB Layout Footprint (Top View) Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 8 November 23, 2016 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 201689J DATA SHEET • SKY13414-485LF: SP4T ANTENNA SWITCH Pin 1 Indicator Skyworks Part Number 201689-006 Figure 6. Typical Part Markings (Top View) 2.00 Seating Plane –C– –A– R0.125 Pin 1 Indicator See Detail A 0.02 +0.03/–0.02 –B– Pin 1 Indicator (0.500) 8X 0.845 12 14 1 11 6X 0.845 4X 0.225 2.00 4 8 0.05 C 2X 0.120 Ref. 0.55 ± 0.05 2X 0.05 C 0.05 C 1 ± 0.1 (0.500) 4X 0.675 7 Exposed Pad 5 14X 0.065 14X 3 0.05 C 4X 0.400 14X 0.255 1 ± 0.1 Top View Side View Bottom View 0.2 ± 0.05 0.18 ± 0.05 Notes: 4 1. All measurements are in millimeters. 2. Dimensions and tolerances according to ASME Y14.5M-1994. 3. Coplanarity applies to the terminals and all other bottom surface metallization. 4. Dimension applies to metallized terminal. If the terminal has a radius on its end, the width dimension should not be measured in that radius area. 0.10 M C A B Detail A Scale: 100X 3X This Rotation 3X Rotated 180° 4X Rotated 90° CW 4X Rotated 90° CCW 201689-007 Figure 7. SKY13414-485LF Package Dimensions Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 201689J • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • November 17, 2016 9 DATA SHEET • SKY13414-485LF: SP4T ANTENNA SWITCH 2.00 ± 0.05 Ø1.50 + 0.10/–0.00 4.00 ± 0.10 1.75 ± 0.10 Pin 1 0.23 ± 0.05 A 2.25 ± 0.05 7º 3.50 ± 0.05 8.00 ± 0.20 0.70 ± 0.05 (Ko) Section A B 4.00 ± 0.10 A B 7º 2.25 ± 0.05 Section B Notes: 1. 2. 3. 4. 5. Carrier tape must meet all requirements of Skyworks GP01-D232 procurement spec for tape and reel shipping. Carrier tape shall be black conductive polycarbonate bakeable material at 125 ˚C temperature. Cover tape shall be transparent conductive with 5.40 mm width. ESD-surface resistivity must meet all ESD requirements of Skyworks specified on GP01-D232. All measurements are in millimeters. 201689-008 Figure 8. SKY13414-485LF Tape and Reel Dimensions Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 10 November 23, 2016 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 201689J DATA SHEET • SKY13414-485LF: SP4T ANTENNA SWITCH Ordering Information Model Name SKY13414-485LF: 0.1 to 3.8 GHz SP4T Antenna Switch Manufacturing Part Number SKY13414-485LF Evaluation Board Part Number SKY13414-485LF-EVB Copyright © 2011-2016 Skyworks Solutions, Inc. All Rights Reserved. Information in this document is provided in connection with Skyworks Solutions, Inc. (“Skyworks”) products or services. These materials, including the information contained herein, are provided by Skyworks as a service to its customers and may be used for informational purposes only by the customer. Skyworks assumes no responsibility for errors or omissions in these materials or the information contained herein. Skyworks may change its documentation, products, services, specifications or product descriptions at any time, without notice. Skyworks makes no commitment to update the materials or information and shall have no responsibility whatsoever for conflicts, incompatibilities, or other difficulties arising from any future changes. No license, whether express, implied, by estoppel or otherwise, is granted to any intellectual property rights by this document. Skyworks assumes no liability for any materials, products or information provided hereunder, including the sale, distribution, reproduction or use of Skyworks products, information or materials, except as may be provided in Skyworks Terms and Conditions of Sale. THE MATERIALS, PRODUCTS AND INFORMATION ARE PROVIDED “AS IS” WITHOUT WARRANTY OF ANY KIND, WHETHER EXPRESS, IMPLIED, STATUTORY, OR OTHERWISE, INCLUDING FITNESS FOR A PARTICULAR PURPOSE OR USE, MERCHANTABILITY, PERFORMANCE, QUALITY OR NON-INFRINGEMENT OF ANY INTELLECTUAL PROPERTY RIGHT; ALL SUCH WARRANTIES ARE HEREBY EXPRESSLY DISCLAIMED. SKYWORKS DOES NOT WARRANT THE ACCURACY OR COMPLETENESS OF THE INFORMATION, TEXT, GRAPHICS OR OTHER ITEMS CONTAINED WITHIN THESE MATERIALS. SKYWORKS SHALL NOT BE LIABLE FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO ANY SPECIAL, INDIRECT, INCIDENTAL, STATUTORY, OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION, LOST REVENUES OR LOST PROFITS THAT MAY RESULT FROM THE USE OF THE MATERIALS OR INFORMATION, WHETHER OR NOT THE RECIPIENT OF MATERIALS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Skyworks products are not intended for use in medical, lifesaving or life-sustaining applications, or other equipment in which the failure of the Skyworks products could lead to personal injury, death, physical or environmental damage. Skyworks customers using or selling Skyworks products for use in such applications do so at their own risk and agree to fully indemnify Skyworks for any damages resulting from such improper use or sale. Customers are responsible for their products and applications using Skyworks products, which may deviate from published specifications as a result of design defects, errors, or operation of products outside of published parameters or design specifications. Customers should include design and operating safeguards to minimize these and other risks. Skyworks assumes no liability for applications assistance, customer product design, or damage to any equipment resulting from the use of Skyworks products outside of stated published specifications or parameters. Skyworks and the Skyworks symbol are trademarks or registered trademarks of Skyworks Solutions, Inc., in the United States and other countries. Third-party brands and names are for identification purposes only, and are the property of their respective owners. Additional information, including relevant terms and conditions, posted at www.skyworksinc.com, are incorporated by reference. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 201689J • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • November 17, 2016 11