SKY65053-377LF

DATA SHEET SKY65053-377LF: 0.45-6.0 GHz Low Noise Transistor Applications • Wireless infrastructure: WLAN, WiMAX, broadband, cellular base stations • Test instrumentation • LNA for GPS receivers • Satellite receivers Features • Externally matched for wideband operation • Noise Figure = 0.6 dB @ 2.4 GHz of device only • Noise Figure = 0.8 dB @ 2.4 GHz including matching network loss • Gain = 16.5 dB @ 2.4 GHz, 5 V, 55 mA • OIP3 = +33.5 dBm @ 2.4 GHz, 5 V, 55 mA • OP1dB = +15.5 dBm @ 2.4 GHz, 5 V, 55 mA • Adjustable supply current, 15 to 100 mA • Unconditionally stable to 18 GHz with reference design circuit • Small, QFN (4-pin, 2 x 2 mm) Pb-free package (MSL3, 260 °C per JEDEC J-STD-020) Figure 1. SKY65053-377LF Block Diagram Description The SKY65053-377LF is a high performance, n-channel lownoise transistor. The device is fabricated from Skyworks advanced depletion mode pHEMT process and is provided in a 2 x 2 mm, 4-pin Quad Flat No-Lead (QFN) package. The transistor’s low Noise Figure (NF), high gain, and excellent 3rd Order Intercept Point (IP3) allow the device to be used in various receiver and transmitter applications. A functional block diagram is shown in Figure 1. The pin configuration and package are shown in Figure 2. Signal pin assignments and functional pin descriptions are provided in Table 1. 1 DRAIN 2 4 SOURCE 3 GATE Figure 2. SKY65053-377LF Pinout – 4-Pin QFN (Top View) Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 201089C • Skyworks Proprietary and Confidential information • Products and Product Information are Subject to Change Without Notice • July 7, 2009 1 SOURCE DATA SHEET • SKY65053-377LF LOW NOISE TRANSISTOR Table 1. SKY65053-377LF Signal Descriptions Pin # 1 2 DRAIN SOURCE Name Description RF output. Supply voltage required through external RF choke. Source lead. Provides DC self-biasing point and AC ground. Pin # 3 4 GATE SOURCE Name RF input Source lead. Provides DC self-biasing point and AC ground. Description Functional Description The SKY65053-377LF is a depletion mode pHEMT designed for low noise, high frequency applications that demand high linearity. The SKY65053-377LF has a typical NF of 0.8 dB tested at the 2.4 GHz wireless LAN frequency band. A gain of 16.5 dB typical is achieved using the same circuit. The SKY65053-377LF can be used for any application from 450 MHz up to 6 GHz. Biasing To properly bias a depletion mode pHEMT, both the gate and drain of the device must be properly biased. At VGS = 0 V and VDS ≥ 2V, the device is in its saturated state and draws the maximum amount of current, IDSS. Typically, the device achieves the best balance of noise and linearity performance at VDS = 5V and IDS = 55 mA. To control IDS, VGS must be biased with a negative voltage supply. To eliminate the need for a negative DC supply, self-biasing should be used when a resistor is placed between one of the source leads and ground. A bypass capacitor should be placed in parallel to this resistor to provide an RF ground and to ensure performance at the operating frequency remains unchanged. When current flows from drain to source and through the resistor, the source voltage becomes biased above DC ground. The gate pin of the device should be left unbiased at 0 V, which creates the desired negative VGS value. This greatly simplifies the design by eliminating the need for a second DC supply. RF Matching Networks The circuit schematic (see Figure 12) shows the recommended RF matching network used for the 2.4 GHz wireless LAN frequency band. Components C1, C2, L1, and L2 provide the necessary impedance match for NF and input return loss. Circuit board and input matching structure losses on the input of the amplifier add directly to the overall NF of the amplifier. It is critical to minimize RF trace lengths and to use high-Q components to achieve optimal NF performance. Components R1 and C10 provide self-bias for the device and RF grounding for one of the two source leads. Component C6 is placed on the opposing source lead and is used to tune the transistor’s internal source inductance. The effect of source inductance varies with frequency. Too little source inductance increases gain and high frequency stability, but at the cost of decreased in-band stability. Too much source inductance decreases high frequency stability and gain, but increases in-band stability. It is very important to find the optimum tuning of source inductance that balances all of these variables. The output matching topology is typical for an RF amplifier. Component L4 is the RF choke that prevents RF signals from reaching the DC supply. Component C11 is the output DC blocking capacitor. Components C12 and L6 provide the best impedance match for best linearity performance. Electrical and Mechanical Specifications The absolute maximum ratings of the SKY65053-377LF are provided in Table 2. The recommended operating conditions are specified in Table 3 and electrical specifications are provided in Table 4. Performance characteristics for the SKY65053-377LF are illustrated in Figures 3 through 10. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 2 July 7, 2009 • Skyworks Proprietary and Confidential information • Products and Product Information are Subject to Change Without Notice • 201089C DATA SHEET • SKY65053-377LF LOW NOISE TRANSISTOR Table 2. SKY65053-377LF Absolute Maximum Ratings Parameter Supply voltage Input power Gate to source voltage Gate to drain voltage Drain to source current Gate to drain current Power dissipation Junction temperature Storage temperature Operating temperature Thermal resistance Note: Symbol VDD PIN VGS VGD IDS IGD PDIS TJ TSTG TOP ΘJC Minimum Typical 6 +15 –5.0 –5.0 110 100 240 150 Maximum Units V dBm V V mA μA mW °C °C °C °C/W –65 –40 220 +125 +85 Exposure to maximum rating conditions for extended periods may reduce device reliability. There is no damage to device with only one parameter set at the limit and all other parameters set at or below their nominal value. CAUTION: Although this device is designed to be as robust as possible, Electrostatic Discharge (ESD) can damage this device. This device must be protected at all times from ESD. Static charges may easily produce potentials of several kilovolts on the human body or equipment, which can discharge without detection. Industry-standard ESD precautions should be used at all times. Table 3. SKY65053-377LF Recommended Operating Conditions Parameter Operating frequency Supply voltage Supply current f VDD IDD Symbol Minimum 0.45 2.00 15 5.00 55 Typical Maximum 6.0 5.25 100 Units GHz V mA Table 4. SKY65053-377LF Electrical Specifications (Note 1) (1 of 2) (TOP = +25 °C, Characteristic Impedance [ZO] = 50 Ω, VDD = 5 V, IDD = 55 mA, Parameters Include Recommended Matching Networks, Unless Otherwise Noted) Parameter Saturated drain current Pinchoff voltage Transconductance Symbol IDSS VP gM Test Condition VDS = 6 V, VGS = 0 V VDS = 6 V, IDS = 2.5% of IDSS VDS = 6 V, gM = ΔIDS/ΔVGS, measured at IDS = 20% of IDSS VGD = VGS = –3 V Min 80 –0.95 80 Typical 100 –0.80 120 Max 120 –0.65 160 Units mA V mS Gate leakage current Noise Figure IGSS NF1 (Note 2) NF2 (Note 3) 1 0.6 0.8 16.5 –12 –7 200 μA dB dB dB dB dB Gain Input return loss Output return loss |S21| |S11| |S22| Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 201089C • Skyworks Proprietary and Confidential information • Products and Product Information are Subject to Change Without Notice • July 7, 2009 3 DATA SHEET • SKY65053-377LF LOW NOISE TRANSISTOR Table 4. SKY65053-377LF Electrical Specifications (Note 1) (2 of 2) (TOP = +25 °C, Characteristic Impedance [ZO] = 50 Ω, VDD = 5 V, IDD = 55 mA, Parameters Include Recommended Matching Networks, Unless Otherwise Noted) Parameter Reverse isolation 3 Order Output Intercept Point 3rd Order Input Intercept Point 1 dB Output Compression Point 1 dB Input Compression Point Stability rd Symbol |S12| OIP3 IIP3 OP1dB IP1dB Test Condition Min Typical –25 Max Units dB dBm dBm dBm dBm K POUT = +5 dBm/tone, 1 MHz spacing POUT = +5 dBm/tone, 1 MHz spacing +33.5 +17 +15.5 0 Unconditionally stable up to 18 GHz >1 Note 1: Performance is guaranteed only under the conditions listed in this Table and is not guaranteed over the full operating or storage temperature ranges. Exceeding any of the conditions listed here may result in permanent damage to the device. Operation at elevated temperatures may reduce reliability of the device. Note 2: NF of device only. Input RF connector, board, and input matching network loss de-embedded from measurement. Note 3: NF of device and matching network. Input RF connector and board loss de-embedded from measurement. Typical Performance Characteristics (TOP = +25 °C, Characteristic Impedance [ZO] = 50 Ω, VDD = 5 V, IDD = 55 mA, Includes Recommended 2.4 GHz Matching Network, Unless Otherwise Noted) 0 20 19 18 –5 Small Signal Gain (dB) 17 16 15 14 13 12 11 10 1.6 1.8 2.0 2.2 2.4 2.6 2.8 3.0 Input Return Loss (dB) –40 oC +25 oC +85 oC –10 –15 –40 oC +25 oC +85 oC Frequency (GHz) –20 –25 1.6 1.8 2.0 2.2 2.4 2.6 2.8 3.0 Frequency (GHz) Figure 3. Small Signal Gain vs Frequency Over Temperature (PIN = –20 dBm) Figure 4. Input Return Loss vs Frequency Over Temperature (PIN = –20 dBm) Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 4 July 7, 2009 • Skyworks Proprietary and Confidential information • Products and Product Information are Subject to Change Without Notice • 201089C DATA SHEET • SKY65053-377LF LOW NOISE TRANSISTOR 0 –5 –10 0 –40 oC +25 oC +85 oC Output Return Loss (dB) –2 –4 –6 –8 –10 –12 –14 –16 –18 –20 Recverse Isolation (dB) –15 –20 –25 –30 –35 –40 –45 –50 1.6 1.8 2.0 2.2 2.4 2.6 2.8 3.0 –40 oC +25 oC +85 oC 1.6 1.8 2.0 2.2 2.4 2.6 2.8 3.0 Frequency (GHz) Frequency (GHz) Figure 5. Reverse Isolation vs Frequency Over Temperature (PIN = –20 dBm) Figure 6. Output Return Loss vs Frequency Over Temperature (PIN = –20 dBm) 1.2 +40 +35 1.0 +30 Noise Figure (dB) 0.8 +25 0.6 0.4 –40 oC +25 oC +85 oC OIP3 (dBm) +20 +15 +10 –40 oC +25 oC +85 oC 0.2 +5 0 2.30 2.35 2.40 2.45 2.50 2.55 2.60 0 4.0 4.2 4.4 4.6 4.8 5.0 5.2 Frequency (GHz) Supply Voltage (V) Figure 7. Noise Figure vs Frequency Over Temperature Figure 8. OIP3 vs Supply Voltage (f = 2.4 GHz, Tone Spacing = 10 MHz, POUT = +5 dBm/Tone) 17.5 8 7 6 5 17.0 μ1 –40 oC μ1 +25 oC μ1 +85 oC μ2 –40 oC μ2 +25 oC μ2 +85 oC 16.5 Gain (dB) μ1, μ2 16.0 4 3 15.5 15.0 14.5 –40 oC +25 oC +85 oC –20 –15 –10 –5 0 +5 2 1 0 0 2 4 6 8 10 12 14 16 18 14.0 Input Power (dBm) Frequency (GHz) Figure 9. Gain vs Input Power Over Temperature (f = 2.4 GHz) Figure 10. Stability vs Frequency Over Temperature (PIN = –20 dBm) Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 201089C • Skyworks Proprietary and Confidential information • Products and Product Information are Subject to Change Without Notice • July 7, 2009 5 DATA SHEET • SKY65053-377LF LOW NOISE TRANSISTOR Evaluation Board Description The SKY65053-377LF Evaluation Board is used to test the performance of the SKY65053-377LF low noise transistor. An assembly drawing for the Evaluation Board is shown in Figure 11. The Evaluation Board schematic diagram is shown in Figure 12. Table 5 provides the Bill of Materials (BOM) list for Evaluation Board components. Circuit Design Considerations Input and output traces have been minimized to reduce losses. All surface mount components are 0402-sized to reduce component parasitics. Use of 0603 or larger components is not recommended. Component spacing has also been minimized. The board is provisioned with two RF connectors and a DC launch. RF connector and board loss up to component C1 is approximately 0.1 dB at 2.4 GHz. It is very important to place multiple ground vias as close to shunt components as possible. This ensures proper grounding and circuit performance. Board material is 10 mil VT47 FR4 with 1 oz. copper cladding. The RF traces are 50 Ω. Caution: Do not ground the exposed pad. Evaluation Board Test Procedure Step 1: Connect RF test equipment to amplifier input/output SMA connectors. Step 2: Connect DC ground. Step 3: Connect VDD to a +5 V supply with a current limit of 100 mA. Verify that the board draws approximately 55 mA. Step 4: Apply RF signal or noise source. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 6 July 7, 2009 • Skyworks Proprietary and Confidential information • Products and Product Information are Subject to Change Without Notice • 201089C DATA SHEET • SKY65053-377LF LOW NOISE TRANSISTOR Caution: Do not ground the exposed pad. S1512 Figure 11. SKY65053-377LF Evaluation Board Assembly Diagram C11 C12 L4 C1 L2 C2 L1 C6 C4 C14 L3 C5 R1 C10 C7 C15 R2 C3 C13 L5 RF Output L6 RF Input VDD S1509 Figure 12. SKY65053-377LF Evaluation Board Schematic Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 201089C • Skyworks Proprietary and Confidential information • Products and Product Information are Subject to Change Without Notice • July 7, 2009 7 DATA SHEET • SKY65053-377LF LOW NOISE TRANSISTOR Table 5. SKY65053-377LF Evaluation Board Bill of Materials Component C1 C2 C3 C4, C5, C7, C8, C9, C14 C6 C10 C11 C12 C13 C15 L1 L2 L3 L4 L5 L6 R1 R2 33 pF 1.2 pF 0.3 pF DNP 10000 pF 10000 pF 3.6 pF 0.3 pF 3.9 pF 1000 pF 12 nH 2 nH DNP 5.6 nH 0Ω 6.8 nH 4.7 Ω 39 Ω 0402 0402 0402 0402 0402 Coilcraft HP Panasonic Taiyo Yuden HK Panasonic Panasonic 0402 0402 0402 0402 0402 0402 0402 0402 Murata GRM015 Murata GRM015 Murata GJM015 Murata GJM015 Murata GRM015 Murata GRM015 Coilcraft HP Coilcraft HP Value 0402 0402 0402 Size Manufacturer/Part Series Murata GRM015 Murata GJM015 Murata GJM015 Package Dimensions The PCB layout footprint for the SKY65053-377LF is shown in Figure 13. Typical case markings are shown in Figure 14. Package dimensions for the 4-pin QFN are shown in Figure 15, and tape and reel dimensions are provided in Figure 16. related to moisture absorption may occur when the part is subjected to high temperature during solder assembly. THE SKY65053-377LF is rated to Moisture Sensitivity Level 3 (MSL3) at 260 °C. It can be used for lead or lead-free soldering. Care must be taken when attaching this product, whether it is done manually or in a production solder reflow environment. Production quantities of this product are shipped in a standard tape and reel format. For packaging details, refer to the Skyworks Application Note, Discrete Devices and IC Switch/Attenuators Tape and Reel Package Orientation, document number 200083. Package and Handling Information Since the device package is sensitive to moisture absorption, it is baked and vacuum packed before shipping. Instructions on the shipping container label regarding exposure to moisture after the container seal is broken must be followed. Otherwise, problems Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 8 July 7, 2009 • Skyworks Proprietary and Confidential information • Products and Product Information are Subject to Change Without Notice • 201089C DATA SHEET • SKY65053-377LF LOW NOISE TRANSISTOR 4X 0.600 2X 0.300 See Detail A for Solderable Area 0.650 1.300 2X 0.600 1.250 0.600 Pin 1 Package Outline See Detail B for Solderable Area 0.55 0.55 0.40 0.30 Detail B Caution: Do not ground the exposed pad. Detail A (3X) S1416 Figure 13. SKY65053-377LF PCB Layout Footprint Pin 1 Indicator Skyworks Part # Figure 14. Typical Case Markings (Top View) Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 201089C • Skyworks Proprietary and Confidential information • Products and Product Information are Subject to Change Without Notice • July 7, 2009 9 S53 DATA SHEET • SKY65053-377LF LOW NOISE TRANSISTOR 0.6+0.1/–0.15 2.00 A B 0.02+0.03/–0.02 Detail B C (0.300) Exposed Pad 1.2+0.1/–0.15 2X 0.65 2.00 1.25 (0.600) 1.30 2X 2X 0.10 C 0.10 C Pin 1 Indicator Detail A 0.55+0.05/–0.04 0.10 C 4X 0.20 Min 4X 0.08 C 3 Top View 0.4 ± 0.1 Side View 0.4 ± 0.1 Bottom View 0.4 ± 0.05 0.3 ± 0.05 0.10 M C A B 5 R 0.15 Detail A All measurements are in millimeters. Dimensioning and tolerancing according to ASME Y14.5M-1994. Detail B (3 Places) S1411 Figure 15. SKY65053-377LF 4-Pin QFN Package Dimensions Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 10 July 7, 2009 • Skyworks Proprietary and Confidential information • Products and Product Information are Subject to Change Without Notice • 201089C DATA SHEET • SKY65053-377LF LOW NOISE TRANSISTOR ∅1.50+ 0.10/–0.00 Pin #1 4.00 ± 0.10 4.00 (Note 4) 2.00 ± 0.05 1.75 ± 0.10 0.30 ± 0.05 (T) B 8.00 +0.30/–0.10 S1555 A 2.30 (Bo) A 1.00 (Ko) B 2.30 (Ao) R0.30 Typ. ∅1.00 Min. B A Notes: 1. Carrier tape: black conductive polystyrene. 2. Cover tape material: transparent conductive HSA. 3. Cover tape size: 5.40 mm width. 4. Ten sprocket hole pitch cumulative tolerance ±0.20 mm. 5. Ao and Bo measurement point to be 0.30 mm from bottom pocket. 6. All measurements are in millimeters. Figure 16. SKY65053-377LF Tape and Reel Dimensions Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 201089C • Skyworks Proprietary and Confidential information • Products and Product Information are Subject to Change Without Notice • July 7, 2009 11 3.50 ± 0.05 DATA SHEET • SKY65053-377LF LOW NOISE TRANSISTOR Ordering Information Model Name SKY65053-377LF Low Noise Transistor Manufacturing Part Number SKY65053-377LF (Pb-free package) Evaluation Board Part Number SKY65053-377LF (2.4 GHz) Copyright © 2009 Skyworks Solutions, Inc. All Rights Reserved. Information in this document is provided in connection with Skyworks Solutions, Inc. (“Skyworks”) products or services. These materials, including the information contained herein, are provided by Skyworks as a service to its customers and may be used for informational purposes only by the customer. Skyworks assumes no responsibility for errors or omissions in these materials or the information contained herein. Skyworks may change its documentation, products, services, specifications or product descriptions at any time, without notice. Skyworks makes no commitment to update the materials or information and shall have no responsibility whatsoever for conflicts, incompatibilities, or other difficulties arising from any future changes. No license, whether express, implied, by estoppel or otherwise, is granted to any intellectual property rights by this document. Skyworks assumes no liability for any materials, products or information provided hereunder, including the sale, distribution, reproduction or use of Skyworks products, information or materials, except as may be provided in Skyworks Terms and Conditions of Sale. THE MATERIALS, PRODUCTS AND INFORMATION ARE PROVIDED “AS IS” WITHOUT WARRANTY OF ANY KIND, WHETHER EXPRESS, IMPLIED, STATUTORY, OR OTHERWISE, INCLUDING FITNESS FOR A PARTICULAR PURPOSE OR USE, MERCHANTABILITY, PERFORMANCE, QUALITY OR NON-INFRINGEMENT OF ANY INTELLECTUAL PROPERTY RIGHT; ALL SUCH WARRANTIES ARE HEREBY EXPRESSLY DISCLAIMED. SKYWORKS DOES NOT WARRANT THE ACCURACY OR COMPLETENESS OF THE INFORMATION, TEXT, GRAPHICS OR OTHER ITEMS CONTAINED WITHIN THESE MATERIALS. SKYWORKS SHALL NOT BE LIABLE FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO ANY SPECIAL, INDIRECT, INCIDENTAL, STATUTORY, OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION, LOST REVENUES OR LOST PROFITS THAT MAY RESULT FROM THE USE OF THE MATERIALS OR INFORMATION, WHETHER OR NOT THE RECIPIENT OF MATERIALS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Skyworks products are not intended for use in medical, lifesaving or life-sustaining applications, or other equipment in which the failure of the Skyworks products could lead to personal injury, death, physical or environmental damage. Skyworks customers using or selling Skyworks products for use in such applications do so at their own risk and agree to fully indemnify Skyworks for any damages resulting from such improper use or sale. Customers are responsible for their products and applications using Skyworks products, which may deviate from published specifications as a result of design defects, errors, or operation of products outside of published parameters or design specifications. Customers should include design and operating safeguards to minimize these and other risks. Skyworks assumes no liability for applications assistance, customer product design, or damage to any equipment resulting from the use of Skyworks products outside of stated published specifications or parameters. Skyworks, the Skyworks symbol, and “Breakthrough Simplicity” are trademarks or registered trademarks of Skyworks Solutions, Inc., in the United States and other countries. Third-party brands and names are for identification purposes only, and are the property of their respective owners. Additional information, including relevant terms and conditions, posted at www.skyworksinc.com, are incorporated by reference. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 12 July 7, 2009 • Skyworks Proprietary and Confidential information • Products and Product Information are Subject to Change Without Notice • 201089C