0
登录后你可以
  • 下载海量资料
  • 学习在线课程
  • 观看技术视频
  • 写文章/发帖/加入社区
会员中心
创作中心
发布
  • 发文章

  • 发资料

  • 发帖

  • 提问

  • 发视频

创作活动
SKY65146

SKY65146

  • 厂商:

    SKYWORKS(思佳讯)

  • 封装:

  • 描述:

    SKY65146 - 3.5 V Broadband MCM Power Amplifier 806-849 MHz - Skyworks Solutions Inc.

  • 数据手册
  • 价格&库存
SKY65146 数据手册
DATA SHEET SKY65146: 3.5 V Broadband MCM Power Amplifier 806–849 MHz Applications G G G G G Block Diagram VD4 (28) VD3 (8) VD2 (22) iDEN® (806–825 MHz) TETRA (806–825 MHz) TDMA (824–849 MHz) AMPS (824–849 MHz) Wireless Local Loop (WLL) VREG (1) CMOS CONTROLLER CIRCUIT RF IN (5) INPUT MATCH PA 1 Features G G G G G G G G G G G INTER STAGE MATCH 1 PA 2 INTER STAGE MATCH 2 OUTPUT STAGE MODULE OUTPUT MATCH RF OUT (15) GaAs HBT IC Low voltage positive bias supply (3.5 V) High gain 39 dB, high power: PSAT 35.6 dBm High efficiency: PAE 51% Good linearity Dual mode operation Large dynamic range 28-pin LCC package (10 x 13.97 x 1.45 mm) Internal RF match Power down control Available on tape and reel Available lead (Pb)-free and RoHS-compliant Package Diagram GND GND GND 2 VD4 NC 7 6 5 NC 4 3 1 28 GND 27 GND 26 GND 25 GND 24 GND 23 GND 22 RFOUT VREG 8 NC 9 NC 10 GND 11 RFIN 12 GND 13 Description The SKY65146 is a fully matched 28-pin surface mount multi-chip module (MCM) amplifier designed for Private Mobile Radio, Wireless Local Loop, and TDMA/AMPS mobile units operating in the 806-849 MHz cellular bandwidth. Microwave Monolithic Integrated Circuits (MMICs), comprised of Gallium Arsenide (GaAs) and Si CMOS, contain all active circuitry in the module, which includes on-board bias circuitry as well as the interstage matching circuit. The input and output match is realized off-chip within the module package to optimize efficiency and high power performance (P3 dB_sat ≅ 35.6 dBm) into a 50 Ω load. Primary bias to the SKY65146 can be supplied directly from a single cell lithiumion or other suitable battery with a nominal output of 3.5 V. No external supply side switch is needed as typical “off” leakage is a few microamperes with full primary voltage supplied from the battery. NC 14 15 16 17 18 10 20 21 VD3 NC NC GND GND The ICs are manufactured on an advanced InGaP HBT process and on a silicon CMOS process, providing for all positive voltage DC supply operation while maintaining high efficiency and good linearity. The module can operate over the temperature range of -40 ˚C to 85 ˚C. A populated evaluation board is available upon request. NEW Skyworks offers lead (Pb)-free, RoHS (Restriction of Hazardous Substances)-compliant packaging. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 200810 Rev. C • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice. • September 8, 2008 GND NC VD2 1 DATA SHEET • SKY65146 Electrical Specifications VCC (VD) = 3.5 V, VREG = 2.75 V, Frequency = 815 MHz, TC = 25 °C, unless otherwise specified. Parameter Frequency range Gain Power gain Input VSWR Saturated output power Power added efficiency Current @ PSAT Quiescent current Harmonic Levels Symbol F lS21l Gp lS11l P3 dB SAT PAE ICC SAT ICCQ 2FO 3FO 4FO RxBN Small signal PO = 29 dBm Small signal Gain Comp < 3 dB PO = P3 dB SAT PO = P3 dB SAT No RF signal PO < P3 dB SAT PO < P3 dB SAT PO < P3 dB SAT PO < 29 dBm CW Output VSWR = 10:1 PO < 29 dBm Junction to case 15:1 19 6.8 270 35.5 12 35.1 47 Condition Min. 806 38.7 38.7 17 35.6 51 2 329 -37 -60 -80 -85 370 dBm % A mA dBc dBc dBc dBm/Hz 40 Typ. Max. 825 Unit MHz dB dB Noise power in Rx band FC + 30 MHz, BW = 18 kHz Noise figure Stability (spurious output) Ruggedness - no damage Thermal resistance NF S Ru θJC 8 -36 dB dBm VSWR °C/W Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 2 September 8, 2008 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice. • 200810 Rev. C DATA SHEET • SKY65146 Recommended Operating Conditions Parameter Supply voltage Regulation voltage Operating frequency Continuous RMS output power Operating case temperature Symbol VCC VREG F PoRMS TC -40 Conditions Min. 3 2.65 806 29 +25 Typ. 3.5 2.75 Max. 4.4 2.85 849 31 +85 Unit V V MHz dBm °C Absolute Maximum Ratings Characteristic RF input power (PIN) Supply voltage (VCC) Regulated supply voltage (VREG) Operating case temperature (TC) Storage temperature(TST) Junction temperature (TJ) Value 11 dBm(1) 6.9 V(2) VCC V (3) -40 °C to +85 °C -55 °C to +125 °C 150 °C CAUTION: Although this device is designed to be as robust as possible, ESD (Electrostatic Discharge) can damage this device. This device must be protected at all times from ESD. Static charges may easily produce potentials of several kilovolts on the human body or equipment, which can discharge without detection. Industry-standard ESD precautions must be employed at all times. 1. For pulsed operation with duty cycle < 25%. 2. When amplifier is biased off (VREG = 0 V). 3. Voltage on VREG pin may not exceed the applied VCC voltage. Performance is guaranteed only under the conditions listed in the specifications table and is not guaranteed under the full range(s) described by the Absolute Maximum specifications. Exceeding any of the absolute maximum/minimum specifications may result in permanent damage to the device and will void the warranty. Each absolute maximum rating listed is an individual parameter. Biasing and driving the amplifier with more than one absolute maximum rating listed may result in permanent damage to the device. Exposure to maximum rating conditions for extended periods may reduce device reliability. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 200810 Rev. C • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice. • September 8, 2008 3 DATA SHEET • SKY65146 Typical Performance Data VCC (VD) = 3.5 V, VREG = 2.75 V, Frequency = 815 MHz, TC = 25 °C, unless otherwise specified. -40 °C 42 25 °C 85 °C 42 3.0 V 3.5 V 4.0 V 4.5 V 40 40 Gain (dB) Gain (dB) 38 36 805 38 36 34 810 815 820 825 -40 -15 10 35 60 85 Frequency (MHz) Temperature (°C ) Gain vs. Frequency Across Temperature -40 °C 43 41 39 25 °C 85 °C 43 41 39 Gain vs. Temperature Across VCC 806 MHz 815.5 MHz 825 MHz Gain (dB) Gain (dB) 37 35 33 31 37 35 33 31 23 28 33 38 23 25 27 29 31 33 35 37 POUT (dBm) POUT (dBm) Gain vs. POUT Across Temperature 3.0 V 43 41 39 37 35 33 31 -19 -20 805 3.5 V 4.0 V 4.5 V -15 -16 Gain vs. POUT Across Frequency -40 °C 25 °C 85 °C lS11l (dB) 23 25 27 29 31 33 35 37 Gain (dB) -17 -18 810 815 820 825 POUT (dBm) Frequency (MHz) Gain vs. POUT Across VCC lS11l vs. Frequency Across Temperature Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 4 September 8, 2008 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice. • 200810 Rev. C DATA SHEET • SKY65146 Typical Performance Data VCC (VD) = 3.5 V, VREG = 2.75 V, Frequency = 815 MHz, TC = 25 °C, unless otherwise specified. -40 °C 2.4 25 °C 85 °C 2.4 806 MHz 815.5 MHz 825 MHz 1.9 1.9 ICC (A) ICC (A) 22 24 26 28 30 32 34 36 38 1.4 1.4 0.9 0.9 0.4 0.4 22 24 26 28 30 32 34 36 38 POUT (dBm) POUT (dBm) ICC vs. POUT Across Temperature 3.0 V 2.4 3.5 V 4.0 V 4.5 V 0.43 ICC vs. POUT Across Frequency 3.0 V 3.5 V 4.0 V 4.5 V 1.9 0.38 1.4 ICCQ (A) 0.33 0.28 22 24 26 28 30 32 34 36 38 -40 ICC (A) 0.9 0.4 -15 10 35 60 85 POUT (dBm) Temperature (°C) ICC vs. POUT Across VCC -40 °C 8 25 °C 85 °C 8 ICCQ vs. Temperature Across VCC 3.0 V 3.5 V 4.0 V 4.5 V 7 7 NF (dB) 6 NF (dB) 6 5 805 810 815 820 825 5 -40 -15 10 35 60 85 Frequency (MHz) Temperature (°C) NF vs. Frequency Across Temperature NF vs. Temperature Across VCC Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 200810 Rev. C • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice. • September 8, 2008 5 DATA SHEET • SKY65146 Typical Performance Data VCC (VD) = 3.5 V, VREG = 2.75 V, Frequency = 815 MHz, TC = 25 °C, unless otherwise specified. 806 MHz 58 48 815.5 MHz 825 MHz 58 48 -40 °C 25 °C 85 °C PAE (%) 28 18 8 PAE (%) 20 22 24 26 28 30 32 34 36 38 38 38 28 18 8 20 22 24 26 28 30 32 34 36 38 POUT (dBm) POUT (dBm) PAE vs. POUT Across Frequency 3.0 V 58 44 48 42 40 38 36 8 20 22 24 26 28 30 32 34 36 38 34 3.5 V 4.0 V 4.5 V PAE vs. POUT Across Temperature -10 dBm -8.5 dBm -9.5 dBm -8 dBm -9 dBm PAE (%) 38 28 18 2nd Harmonics (dB) POUT (dBm) -40 -15 10 35 60 85 PAE vs. POUT Across VCC -10 dBm -8.5 dBm 52 49 -9.5 dBm -8 dBm -9 dBm Temperature (°C) 2nd Harmonics vs. Temperature Across PIN -10 dBm -8.5 dBm 44 42 40 38 36 34 805 -9.5 dBm -8 dBm -9 dBm 2nd Harmonics (dB) 46 43 40 37 34 3.00 2nd Harmonics (dB) 3.25 3.50 3.75 4.00 4.25 4.50 810 815 820 825 VCC (V) Frequency (MHz) 2nd Harmonics vs. VCC Across PIN 2nd Harmonics vs. Frequency Across PIN Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 6 September 8, 2008 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice. • 200810 Rev. C DATA SHEET • SKY65146 Typical Performance Data VCC (VD) = 3.5 V, VREG = 2.75 V, Frequency = 815 MHz, TC = 25 °C, unless otherwise specified. -10 dBm -8.5 dBm 61 60 59 58 57 56 -40 57 805 -9.5 dBm -8 dBm -9 dBm 61 -10 dBm -8.5 dBm -9.5 dBm -8 dBm -9 dBm 3rd Harmonics (dB) 3rd Harmonics (dB) 60 59 58 -15 10 35 60 85 810 815 820 825 Temperature ( C ) Frequency (MHz) 3rd Harmonics vs. Temperature Across PIN -10 dBm -8.5 dBm 62 -9.5 dBm -8 dBm -9 dBm 84 82 3rd Harmonics vs. Frequency Across PIN -10 dBm -8.5 dBm -9.5 dBm -8 dBm -9 dBm 3rd Harmonics (dB) 4th Harmonics (dB) 3.25 3.50 3.75 4.00 4.25 4.50 61 80 78 76 74 -40 60 59 58 3.00 -15 10 35 60 85 VCC (V) Temperature (°C) 3rd Harmonics vs. VCC Across PIN -10 dBm -8.5 dBm 83 -9.5 dBm -8 dBm -9 dBm 4th Harmonics vs. Temperature Across PIN -10 dBm -8.5 dBm 82 -9.5 dBm -8 dBm -9 dBm 4th Harmonics (dB) 805 810 815 820 825 4th Harmonics (dB) 81 80 79 78 77 75 76 3.00 3.25 3.50 3.75 4.00 4.25 4.50 Frequency (MHz) VCC (V) 4th Harmonics vs. Frequency Across PIN 4th Harmonics vs. VCC Across PIN Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 200810 Rev. C • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice. • September 8, 2008 7 DATA SHEET • SKY65146 Typical Performance Data VCC (VD) = 3.5 V, VREG = 2.75 V, Frequency = 815 MHz, TC = 25 °C, unless otherwise specified. 50 40 30 S11 S21 S22 36.0 35.5 35.0 P1 dB (dBm) Sij (dB) 20 10 0 -10 -20 0.70 0.75 0.80 0.85 0.90 0.95 1.00 34.5 34.0 33.5 33.0 32.5 32.0 800 820 840 860 880 900 920 940 Frequency (GHz) Frequency (MHz) S-Parameters vs. Frequency 806 MHz 850 MHz 40 39 38 37 50 815.5 MHz 890 MHz 825 MHz 930 MHz P1 dB v s. Frequency 55 PAE @ P1 dB (%) 45 40 35 30 800 820 840 860 880 900 920 940 OIP3 (dBm) 36 35 34 33 32 31 30 16 18 20 22 24 26 28 Frequency (MHz) Power Out/Tone (dBm) PAE @ P1 dB v s. Frequency OIP3 vs. POUT/Tone Across Frequency Tone Spacing =1 MHz Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 8 September 8, 2008 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice. • 200810 Rev. C DATA SHEET • SKY65146 Application Circuit Notes Center Ground. It is extremely important that the device paddle be sufficiently grounded for both thermal and stability reasons. Multiple small vias are acceptable and will work well under the device if solder migration is an issue. VD2 (Pin 1). Supply voltage for output (final) stage collector bias (typically 3.5 V). Bypassing of VD3 is accomplished with C2 and C3 and should be placed in the approximate location shown on the Evaluation Board, but placement is not critical. Ground (Pins 2, 3, 6, 11, 13, 16, 19, 20, 23–28). Attach all ground pins to the RF ground plane with the largest diameter and lowest inductance via that the layout will allow. Multiple small vias are also acceptable and will work well under the device if solder migration is an issue. No Connect (Pins 4, 5, 9, 10, 14, 17, 18, 21). The pins are open and may or may not be connected to ground. VD4 (Pin 7). Supply voltage for base bias circuitry to all stages (typically 3.5 V). Bypassing of VD3 is accomplished with C1 which should be placed in the approximate location shown on the Evaluation Board, but placement is not critical. VREG (Pin 8). VREG is the regulated bias enable control voltage to the silicon CMOS controller, 0.0 V = Off, 2.75 V = On. Nominal “On” operating range is between 2.65 VDC and 2.85 VDC. VREG set to 0 VDC will force the amplifier into standby mode. RF_IN (Pin 12). Amplifier RF Input Pin. ZO = 50 Ω. The module includes an onboard internal DC blocking capacitor. All impedance matching is provided internal to the module. VD3 (Pin 15). Supply voltage for driver collector bias (typically 3.5V). Bypassing of VD3 is accomplished with C4 and C5 which should be placed in the approximate location shown on the Evaluation Board, but placement is not critical. RF_OUT (Pin 22). Amplifier RF Output Pin. ZO = 50 Ω. The module includes an onboard internal DC blocking capacitor. All impedance matching is provided internally to the module. Package and Handling Information Since the device package is sensitive to moisture absorption, it is baked and vacuum packed before shipping. Instructions on the shipping container label regarding exposure to moisture after the container seal is broken must be followed. Otherwise, problems related to moisture absorption may occur when the part is subjected to high temperature during solder assembly. Please refer to Skyworks’ solder reflow application note, available at www.skyworksinc.com, for instructions on mounting the SKY65146 to a printed circuit board. Production quantities of this product are shipped in a standard tape and reel format. For packaging details, refer to the Skyworks Application Note, Tape and Reel, document number 101568. Electrostatic Discharge (ESD) Sensitivity The SKY65146 is a static-sensitive electronic device. Do not operate or store near strong electrostatic fields. Take proper ESD precautions. Theory of Operation The SKY65146 is a fully matched 3-stage GaAs HBT power amplifier module consisting of on-chip interstage matching circuits and bias circuitry. The input and output match is realized off-chip, but within the module package. The amplifier employs series feedback on the first and second stages to provide for high gain and stability and power of up to 4 W. The module includes a silicon CMOS controller circuit to provide a regulated bias enable control, VREG (0–2.75 V) for amplifier On/Off operation. In off operation, supply current is a few microamperes with VREG = 0 V. The module operates with all positive DC voltages while maintaining high efficiency and good linearity. The nominal operating voltage is 3.5 V for maximum power, but can be operated at slightly lower voltages for other mobile applications. Application Circuit VD2 C2 10 F VD4 C1 10 F VREG 8 NC 9 NC 10 11 RF_IN 50 Ω 12 13 NC 14 15 VD3 C4 10 F C5 1000 pF 16 17 NC 18 NC 19 20 21 NC 7 6 NC 5 NC 4 3 2 1 28 27 26 C3 1000 pF SKY65146 25 24 23 22 50 Ω RF_OUT Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 200810 Rev. C • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice. • September 8, 2008 9 DATA SHEET • SKY65146 Pin Assignments Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 Pin Name VD2 GND GND N/C N/C GND VD4 VREG N/C N/C GND RFIN GND N/C VD3 GND N/C N/C GND GND N/C RFOUT GND GND GND GND GND GND Description Supply voltage for output (final) stage collector bias (typically 3.5 V) Low inductance ground connection Evaluation Board VCTL (NC) GND VREG VD4 VD3 VD2 VD1 (NC) C2 J3 RF In U1 C1 SKY65146 C3 Pin 1 J2 RF Out C5 C4 GND Low inductance ground connection No connect No connect Low inductance ground connection Supply voltage for base bias circuitry to all stages (typically 3.5 V) Regulated bias enable control voltage, 0.0 = Off, 2.75 V = On No connect No connect Low inductance ground connection 806–849 MHz RF input signal 50 Ω Low inductance ground connection No connect Supply voltage for driver collector bias (typically 3.5 V) Low inductance ground connection No connect No connect Low inductance ground connection Low inductance ground connection No connect 806–849 MHz RF output signal 50 Ω Low inductance ground connection Low inductance ground connection Low inductance ground connection Low inductance ground connection Low inductance ground connection Low inductance ground connection J1 SKY65146 Test Fixture TW16-D390- Recommended Solder Reflow Profiles Refer to the “Recommended Solder Reflow Profile” Application Note. Tape and Reel Information Refer to the “Discrete Devices and IC Switch/Attenuators Tape and Reel Package Orientation” Application Note. Center attachment pad must have a low inductance and low thermal resistance connection to the customer's printed circuit board ground plane. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 10 September 8, 2008 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice. • 200810 Rev. C DATA SHEET • SKY65146 Evaluation Board Description The Skyworks SKY65146 Evaluation Board is used to test the performance of the SKY65146 power amplifier module. The following design considerations are general in nature and must be followed regardless of final use or configuration. 1. Paths to ground should be made as short as possible. 2. The ground pad of the SKY65146 power amplifier module has special electrical and thermal grounding requirements. This pad is the main thermal conduit for heat dissipation. Since the circuit board acts as the heat sink, it must shunt as much heat as possible from the amplifiers. As such, design the connection to the ground pad to dissipate the maximum wattage produced to the circuit. Multiple vias to the grounding layer are required. NOTE: Junction temperature (TJ) of the device increases with a poor connection to the slug and ground. This reduces the lifetime of the device. Capacitors C6 and C7 are shown on EVB, but are not used. Evaluation Board Test Procedure Step 1. Connect RF test equipment to Amplifier input/output SMA connectors. Step 2. Connect DC ground. Step 3. Connect all VCC (VD) lines to 3.5 V supply and VREG to 2.75 V. Verify the ICQ current is approximately 329 mA. Step 4. Apply RF signal data -30 dBm level and observe that the output level is approximately 8 dBm or the gain of the device is approximately 38 dB. NOTE: It is important that the VD2, VD3, and VD4 voltage source be adjusted such that 3.5 V is measured at the board. The high collector currents will drop the collector voltage significantly if long leads are used. Adjust the bias voltage to compensate. Bill of Material for Evaluation Board Part 1 2 3 4 5 ID C1 C2 C3 C4 C5 QTY 1 1 1 1 1 Size 1206 1206 0402 1206 0402 Value 10 10 1000 10 1000 Units µF µF pF µF pF Manufacturer AVX AVX Murata AVX Murata Product Number TAJA106M006R TAJA106M006R GRM155R71H102KA01 TAJA106M006R GRM155R71H102KA01 Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 200810 Rev. C • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice. • September 8, 2008 11 DATA SHEET • SKY65146 Evaluation Board Stack-Up Cross Section Name Thickness (mm) Material L1 Lam1 L2 Lam2 L3 Lam3 L4 0.025 0.400 0.025 0.600 0.025 0.400 0.025 Cu Rogers 4003 Cu FR4 Cu FR4 Cu Package Outline εr – 3.38 – 4.00 – 10.04 Pin 1 Indicator Top 14.04 4.00 – Branding Specifications 1.45 ± 0.1 4X 3.81 4X 2.54 4X 1.27 Mark Pin 1 Identifier Pin 28 0 Manufacturing Part Number Revision Number 28X SMT Pad SKY65146 EXXXXX.XX YYWW MX (0.2x 45°) Pin 1 Indicator See Detail A Pin 1 See Detail B Lot Number YY = Manufacture Year WW = Week Packaged Sealed MX = Country Code C 12X 1 12X 2 12X 3 12X 4 0 4X 1.27 4X 2.54 4X 3.81 14X 6.873 14X 4.873 2.5 1.5 0.5 54X Solder Mask Openings See Detail B 1.163 ± 0.05 (0.147) 0.875 0.02X 45° 0.875 R 0.05 Max. Detail A Units = mm. Detail B 0.875 0.875 R 0.05 Max. 1.016 ± 0.05 0.762 ± 0.05 Detail C (R 0.381) 0.889 ± 0.05 (R 0.508) Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 12 September 8, 2008 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice. • 200810 Rev. C DATA SHEET • SKY65146 Recommended Footprint 10.34 mm 14X 0.762 mm Pin 28 Solder Mask 10.44 mm Pin 28 0.20 X 45° 18X 2.5 mm 28X 0.862 mm 28X 1.286 mm 14X 1.186 mm Pin 1 Pin 1 12X 3 mm 14.34 mm 12X 1 mm 12X 2 mm 14.44 mm C L 1.27 mm Typ. 1.27 mm Typ. C L 0.6 mm 12X 4 mm 0.875 mm Typ. R0.431 mm Typ. 0.25 mm Typ. Package Outline R0.381 mm Typ. 0.25 mm Typ. 0.875 mm Typ. C L 18X 1.5 mm 18X 0.5 mm Thermal via array Ø0.3 mm on 0.7 mm pitch additional vias in common ground pad will improve thermal performance C L 0.6 mm Thermal vias should be tented and filled with solder mask 30-35 µm copper plating recommended. Stencil Pattern 10.34 mm 18X 2.5 mm 28X 28X 0.762 mm 1.186 mm Pin 28 0.20 X 45° Pin 1 12X 3 mm 12X 1 mm 12X 2 mm 12X 4 mm 0.875 mm Typ. Stencil aperture size of 80 to 100% of the module/pkg 0.875 mm solder mask Typ. openings. Package Outline C L 18X 1.5 mm 18X 0.5 mm C L 1.27 mm 14.34 mm Typ. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 200810 Rev. C • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice. • September 8, 2008 13 DATA SHEET • SKY65146 Ordering Information Model Name SKY65146: 3.5 V Broadband MCM Power Amplifier 806–849 MHz Manufacturing Part Number SKY65146-21 (Pb-free package) Evaluation Kit Part Number TW16-D390 Copyright © 2007, 2008, Skyworks Solutions, Inc. All Rights Reserved. Information in this document is provided in connection with Skyworks Solutions, Inc. (“Skyworks”) products or services. These materials, including the information contained herein, are provided by Skyworks as a service to its customers and may be used for informational purposes only by the customer. Skyworks assumes no responsibility for errors or omissions in these materials or the information contained herein. Skyworks may change its documentation, products, services, specifications or product descriptions at any time, without notice. Skyworks makes no commitment to update the materials or information and shall have no responsibility whatsoever for conflicts, incompatibilities, or other difficulties arising from any future changes. No license, whether express, implied, by estoppel or otherwise, is granted to any intellectual property rights by this document. Skyworks assumes no liability for any materials, products or information provided hereunder, including the sale, distribution, reproduction or use of Skyworks products, information or materials, except as may be provided in Skyworks Terms and Conditions of Sale. THE MATERIALS, PRODUCTS AND INFORMATION ARE PROVIDED “AS IS” WITHOUT WARRANTY OF ANY KIND, WHETHER EXPRESS, IMPLIED, STATUTORY, OR OTHERWISE, INCLUDING FITNESS FOR A PARTICULAR PURPOSE OR USE, MERCHANTABILITY, PERFORMANCE, QUALITY OR NON-INFRINGEMENT OF ANY INTELLECTUAL PROPERTY RIGHT; ALL SUCH WARRANTIES ARE HEREBY EXPRESSLY DISCLAIMED. SKYWORKS DOES NOT WARRANT THE ACCURACY OR COMPLETENESS OF THE INFORMATION, TEXT, GRAPHICS OR OTHER ITEMS CONTAINED WITHIN THESE MATERIALS. SKYWORKS SHALL NOT BE LIABLE FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO ANY SPECIAL, INDIRECT, INCIDENTAL, STATUTORY, OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION, LOST REVENUES OR LOST PROFITS THAT MAY RESULT FROM THE USE OF THE MATERIALS OR INFORMATION, WHETHER OR NOT THE RECIPIENT OF MATERIALS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Skyworks products are not intended for use in medical, lifesaving or life-sustaining applications, or other equipment in which the failure of the Skyworks products could lead to personal injury, death, physical or environmental damage. Skyworks customers using or selling Skyworks products for use in such applications do so at their own risk and agree to fully indemnify Skyworks for any damages resulting from such improper use or sale. Customers are responsible for their products and applications using Skyworks products, which may deviate from published specifications as a result of design defects, errors, or operation of products outside of published parameters or design specifications. Customers should include design and operating safeguards to minimize these and other risks. Skyworks assumes no liability for applications assistance, customer product design, or damage to any equipment resulting from the use of Skyworks products outside of stated published specifications or parameters. Skyworks, the Skyworks symbol, and “Breakthrough Simplicity” are trademarks or registered trademarks of Skyworks Solutions, Inc., in the United States and other countries. Third-party brands and names are for identification purposes only, and are the property of their respective owners. Additional information, including relevant terms and conditions, posted at www.skyworksinc.com, are incorporated by reference. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 14 September 8, 2008 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice. • 200810 Rev. C
SKY65146 价格&库存

很抱歉,暂时无法提供与“SKY65146”相匹配的价格&库存,您可以联系我们找货

免费人工找货