SKY66001-11

DATA SHEET SKY66001-11: 2100 to 2200 MHz, +19 dBm Linear Power Amplifier Applications  Residential femtocells VEN  WCDMA, Band 1 MMIC VCC1  Small cells Power Stage Bias Driver Stage Bias Features RF_IN  Small signal gain: 28.6 dB Input Match DA Inter-Stage Match PA Output Match RF_OUT VCC2 CPL_OUT CPL_IN  ACLR at POUT = +19 dBm: -51 dBc  PA on/off control S2993  I/O impedance internally matched to 50 Ω Figure 1. SKY66001-11 Linear PA Block Diagram  Single DC supply: 3.3 V to 4.6 V  Minimal number of external components required Description  Small footprint MCM (10-pin, 3 x 3 mm) package (MSL3, 260 C per JEDEC J-STD-020) The SKY66001-11 linear power amplifier (PA) is a fully matched surface-mount module developed for WCDMA applications operating from 2100 to 2200 MHz. The device meets the stringent spectral linearity requirements of WCDMA femtocell applications with high power-added efficiency. An integrated directional coupler eliminates the need for any external coupler. Skyworks GreenTM products are compliant with all applicable legislation and are halogen-free. For additional information, refer to Skyworks Definition of GreenTM, document number SQ04–0074. VCC1 1 10 VCC2 RF_IN 2 9 RF_OUT GND 3 8 CPL_IN GND 4 7 GND VEN 5 6 CPL_OUT S2992 The GaAs MMIC contains all active amplifier circuitry, which includes input and interstage matching circuits. An output match into a 50 Ω load, realized off-chip within the module package, optimizes efficiency and power performance. The SKY66001-11 is manufactured with Skyworks InGaP GaAs HBT process, which provides for all positive voltage DC supply operation and maintains high efficiency and good linearity. The primary bias to the device can be supplied directly from any suitable power supply with an output of 4.2 V. Power down is achieved by setting the VEN pin to 0 V. No external supply side switch is needed since typical “off” leakage is a few microamps with full primary voltage supplied from the main power supply. The SKY66001-11 is packaged in a 10-pin, 3 x 3 mm Multi-Chip Module (MCM), which allows for a highly manufacturable low-cost solution. A functional block diagram of the SKY66001-11 is shown in Figure 1. The 10-pin MCM package and pinout are shown in Figure 2. Signal pin assignments and functional pin descriptions are provided in Table 1. Figure 2. SKY66001-11 Pinout (Top View) Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 201936F • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • October 6, 2017 1 DATA SHEET • SKY66001-11: 2100 TO 2200 MHz, +19 DBM LINEAR POWER AMPLIFIER Table 1. SKY66001-11 Signal Descriptions Pin Name Description Pin Input stage supply voltage 6 Name Description 1 VCC1 CPL_OUT RF coupler output 2 RF_IN RF input port 3 GND Ground 7 GND Ground 8 CPL_IN RF coupler input 4 GND Ground 9 RF_OUT RF output port 5 VEN Enable 10 VCC2 Output stage supply voltage Technical Description Electrical and Mechanical Specifications The SKY66001-11 PA contains all of the needed RF matching and DC biasing circuits. The device is a two-stage, HBT InGaP device optimized for high linearity and power efficiency. These features make the device suitable for wideband digital applications where PA linearity and power consumption are of critical importance (e.g., small cell and infrastructure applications). The absolute maximum ratings of the SKY66001-11 are provided in Table 2. The recommended operating conditions are specified in Table 3 and electrical specifications are provided in Table 4. Typical performance characteristics of the SKY66001-11 are illustrated in Figures 3 to 11. The device is designed for standard WCDMA modulated signals. Under these stringent test conditions, the device exhibits excellent spectral purity and power efficiency. Table 2. SKY66001-11 Absolute Maximum Ratings1 Parameter Supply voltage (VCC1, VCC2) Symbol VCC Minimum Maximum Units 0 +4.6 V Total supply current ICC 700 mA Logic control input voltage (VEN) VCTL -0.5 3.1 V Case operating temperature2 TC -40 +85 C Storage temperature TSTG -55 Junction temperature TJ Thermal resistance ΘJC Electrostatic discharge: Charged Device Model (CDM), Class 4 Human Body Model (HBM), Class 1C Machine Model (MM), Class A ESD +150 C +150 C 60 C/W 500 1000 150 V V V 1 Exposure to maximum rating conditions for extended periods may reduce device reliability. There is no damage to device with only one parameter set at the limit and all other parameters set at or below their nominal value. Exceeding any of the limits listed here may result in permanent damage to the device. 2 Case operating temperature (Tc) refers to the temperature of the bottom ground pad. ESD HANDLING: Although this device is designed to be as robust as possible, electrostatic discharge (ESD) can damage this device. This device must be protected at all times from ESD when handling or transporting. Static charges may easily produce potentials of several kilovolts on the human body or equipment, which can discharge without detection. Industry-standard ESD handling precautions should be used at all times. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 2 October 6, 2017 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 201936F DATA SHEET • SKY66001-11: 2100 TO 2200 MHz, +19 DBM LINEAR POWER AMPLIFIER Table 3. SKY66001-11 Recommended Operating Conditions Parameter Symbol Min Typ 2100 Max Units 2200 MHz Frequency range f Supply voltage (VCC1, VCC2)1 VCC 4.0 4.2 4.6 V Logic control input voltage: Logic high Logic low VIH VIL 1.35 0 1.80 3.10 0.5 V V PA enable current IEN