SKY73084-11

DATA SHEET SKY73084-11: 300 – 500 MHz High Gain and Linearity Diversity Downconversion Mixer Applications • 2G/3G base station transceivers: − GSM/EDGE, CDMA, UMTS/WCDMA • Land mobile radio • High performance radio links Description The SKY73084-11 is a fully integrated diversity mixer that includes Local Oscillator (LO) drivers, an LO switch, high linearity mixers, and large dynamic range Intermediate Frequency (IF) amplifiers. Low loss RF baluns have also been included to reduce design complications and lower system cost. The SKY73084-11 features an input IP3 of +25.2 dBm and a Noise Figure (NF) of 9.4 dB, making the device an ideal solution for high dynamic range systems such as 2G/3G base station receivers. The LO switch provides more than 60 dB of isolation between LO inputs and supports the switching time required for GSM/EDGE base stations. The SKY73084-11 is manufactured using a robust silicon BiCMOS process and has been designed for optimum long-term reliability. The SKY73084-11 diversity downconversion mixer is provided in a compact, 36-pin Multi-Chip Module (MCM). A functional block diagram is shown in Figure 1. The pin configuration and package are shown in Figure 2. Signal pin assignments and functional pin descriptions are provided in Table 1. Features • Operating frequency range: 300 to 500 MHz • IF frequency range: 50 to 250 MHz • Conversion gain: 9.8 dB • Input IP3: +25.2 dBm • Output IP3: +35 dBm • Noise figure: 9.4 dB • Integrated LO drivers • Integrated low loss RF baluns • High linearity IF amplifiers • On-chip SPDT LO switch (greater than 60 dB LO-to-LO isolation) • Small, MCM (36-pin, 6 x 6 mm) Pb-free package (MSL3, 260 °C per JEDEC J-STD-020) IFA+ IFA– RFA LO1 LO_SEL (Switch Enable) RFB LO2 IFB+ IFB– S643 Figure 1. SKY73084-11 Block Diagram Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 200884F • Skyworks Proprietary and Confidential information • Products and Product Information are Subject to Change Without Notice • April 3, 2009 1 DATA SHEET • SKY73084-11 DOWNCONVERSION MIXER VCC_RFA VCC_IFA IFA+ GND RIFA 29 IFA– NC NC 36 35 34 33 32 31 30 28 27 26 25 24 23 22 21 20 19 RFA NC GND VCC_LO GND VCC_LO GND NC RFB NC 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 LO2 GND GND GND LO_SEL GND VCC_LO GND LO1 VCC_RFB VCC_IFB IFB+ IFB– NC GND NC RIFB NC S646 Figure 2. SKY73084-11 Pinout – 36-Pin MCM (Top View) Table 1. SKY73084-11 Signal Descriptions Pin # 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 RFA NC GND VCC1 GND VCC2 GND NC RFB VCC3 NC GND IFB+ IFB– NC VCC4 RIFB NC Name Description RF channel A input No connect Ground DC supply, +5 V Ground DC supply, +5 V Ground No connect RF channel B input DC supply, +5 V No connect Ground IF channel B positive output IF channel B negative output No connect DC supply, +5 V IF channel B bias control No connect Pin # 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 LO1 GND VCC5 GND LO_SEL GND GND GND LO2 NC RIFA VCC6 NC IFA+ IFA– GND NC VCC7 Name Description Local oscillator #1 input Ground DC supply, +5 V Ground Local oscillator switch select Ground Ground Ground Local oscillator #2 input No connect IF channel A bias control DC supply, +5 V No connect IF channel A positive output IF channel A negative output Ground No connect DC supply, +5 V Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 2 April 3, 2009 • Skyworks Proprietary and Confidential information • Products and Product Information are Subject to Change Without Notice • 200884F DATA SHEET • SKY73084-11 DOWNCONVERSION MIXER Functional Description The SKY73084-11 is a high gain diversity mixer, optimized for base station receiver applications. The device consists of two diversity channels, each consisting of a low loss RF balun, high linearity passive mixer, and a low noise IF amplifier. LO amplifiers are also included that allow the SKY73084-11 to connect directly to the output of a Voltage Controlled Oscillator (VCO). This eliminates the extra gain stages needed by most discrete passive mixers. A Single Pole, Double Throw (SPDT) switch has been included to select between two different LO inputs for frequency hopping applications (i.e., GSM). RF Baluns and Passive Mixer The RF baluns provide a single ended input, which can easily be matched to 50 Ω using a simple matching circuit. The RF baluns offer very low loss and excellent amplitude and phase balance. The high linearity mixer is a passive, double balanced mixer that provides a very low insertion loss, and excellent 3rd Order Input Insertion Point (IIP3) and linearity performance. Additionally, the balanced nature of the mixer provides for excellent port-to-port isolation. LO Buffers and SPDT LO Switch The LO buffers allow the input power of the SKY73084-11 to be programmed in the range of –6 to +6 dBm. The LO section has been optimized for high-side LO injection. However, the LO can be driven over a wide frequency range with only slight degradation in performance. A high isolation SPDT switch allows the SKY73084-11 to be used for frequency hopping applications. This switch provides greater than 60 dB of LO1 to LO2 isolation: LO_SEL Logic: High Low State: LO1 enabled LO2 enabled For applications that do not require frequency hopping, LO_SEL is fixed to one state and the appropriate LO input is used. IF Amplifier The SKY73084-11 includes high dynamic range IF amplifiers that follow the passive mixers in the signal path. The outputs require a supply voltage connection using inductive chokes. These choke inductors should be high-Q and have the ability to handle 200 mA or greater. A simple matching network allows the output ports to be matched to a balanced 200 Ω impedance. The IF amplifiers are optimized for IF frequencies between 50 and 250 MHz. The IF amplifiers can be operated outside of this range, but with a slight degradation in performance. Electrical and Mechanical Specifications The absolute maximum ratings of the SKY73084-11 are provided in Table 2. The recommended operating conditions are specified in Table 3 and electrical specifications are provided in Table 4. Typical performance characteristics of the SKY73084-11 are illustrated in Figures 3 through 31. Table 2. SKY73084-11 Absolute Maximum Ratings Parameter Supply voltage, +5 V (VCC1 – VCC7) Supply current RF input power LO input power Operating case temperature Junction temperature Storage case temperature VCC ICC PRF PLO TC TJ TSTG –40 –40 0 Symbol Minimum 4.5 Typical 5.0 370 Maximum 5.5 430 +20 +20 +85 +150 +125 Units V mA dBm dBm °C °C °C Notes: Exposure to maximum rating conditions for extended periods may reduce device reliability. There is no damage to device with only one parameter set at the limit and all other parameters set at or below their nominal value. Nominal thermal resistance (junction to center ground pad) is 5.1 °C/W. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 200884F • Skyworks Proprietary and Confidential information • Products and Product Information are Subject to Change Without Notice • April 3, 2009 3 DATA SHEET • SKY73084-11 DOWNCONVERSION MIXER Table 3. SKY73084-11 Recommended Operating Conditions Parameter RF frequency range LO frequency range (Note 1) IF frequency range Supply voltage, +5 V (VCC1 – VCC7) Supply current LO input power LO select logic: high low Operating case temperature FRF FLO FIF VCC ICC PLO LO_SELH LO_SELL TC –6 2.2 0.8 –40 +85 Symbol Minimum 300 350 50 4.75 5.00 370 0 +6 Typical Maximum 500 600 250 5.25 Units MHz MHz MHz V mA dBm V V °C Note 1: The SKY73084-11 has been optimized for high-side LO injection. However, the LO can be used outside of the specified frequency range with degraded performance. Table 4. SKY73084-11 Electrical Specifications (1 of 2) (Voltage Supply = +5 V, TC = +25 °C, LO = 0 dBm, RF Frequency = 350 MHz, IF Frequency = 90 MHz, LO Frequency = 440 MHz, Unless Otherwise Noted) Parameter Conversion gain G Symbol Test Condition FRF = 328 to 388 MHz, VCC = 4.75 to 5.25 V, PLO = –3 to +3 dBm FRF = 350 MHz, Tc = –40 to +85 °C NF FRF = 350 MHz FRF = 350 MHz, Tc = –40 to +85 °C NFBLK IIP3 Blocking signal input power = +8 dBm FRF = 350 and 350.8 MHz, PRF = –10 dBm/each tone, VCC = 4.75 to 5.25 V, PLO = –3 to +3 dBm FRF = 350 and 350.8 MHz, Tc = –40 to +85 °C OIP3 FRF = 350 and 350.8 MHz, PRF = –10 dBm/each tone, VCC = 4.75 to 5.25 V, PLO = –3 to +3 dBm PRF = –10 dBm PRF = –10 dBm PRF = +2 dBm +9.5 +23.5 Min 7.5 Typical 9.8 Max Units dB Gain variation over temperature Noise Figure Noise Figure variation over temperature Noise Figure with a blocker signal Third order input intercept point ±1 9.4 ±0.8 18 +25.2 25 11.0 dB dB dB dB dBm Input IP3 variation over temperature Third order output intercept point ±0.4 +35 dB dBm 2RF – 2LO 3RF – 3LO 4RF – 3LO Input 1 dB compression point Output 1 dB compression point LO1 to LO2 isolation Channel-to-channel isolation RF to IF isolation 2x2 3x3 4x3 IP1dB OP1dB –63 –85 –102 +13.2 +22.0 –57 –70 –95 dBc dBc dBc dBm dBm dB dB dB FRF = 350 MHz, FLO = 440 MHz FRF = 350 MHz, FLO = 440 MHz Frf = 350 MHz 40 37 30 63 41 76 Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 4 April 3, 2009 • Skyworks Proprietary and Confidential information • Products and Product Information are Subject to Change Without Notice • 200884F DATA SHEET • SKY73084-11 DOWNCONVERSION MIXER Table 4. SKY73084-11 Electrical Specifications (2 of 2) (Voltage Supply = +5 V, TC = +25 °C, LO = 0 dBm, RF Frequency = 350 MHz, IF Frequency = 90 MHz, LO Frequency = 440 MHz, Unless Otherwise Noted) Parameter LO leakage: 1xLO to RF port 2xLO to RF port 3xLO to RF port 4xLO to RF port 1xLO to IF port LO_SEL input LO switching time RF port input return loss LO port input return loss IF port input return loss ZIN_RF ZIN_LO ZOUT_IF With external matching components With external matching components With external matching components 14 14 14 Symbol Test Condition FRF = 350 MHz, FLO = 440 MHz Min Typical –40 –28 –50 – –40 –20 +150 Max –25 –22 –28 –28 –23 +250 1.0 Units dBm dBm dBm dBm dBm µA µs dB dB dB 12.0 11.5 11.0 10.5 4.75 V 5.00 V 5.25 V 12.0 11.5 11.0 10.5 –40 oC +25 oC +85 oC Gain (dB) Gain (dB) 10.0 9.5 9.0 8.5 8.0 7.5 7.0 328 336 344 352 360 368 376 384 10.0 9.5 9.0 8.5 8.0 7.5 7.0 328 336 344 352 360 368 376 384 RF Frequency (MHz) RF Frequency (MHz) Figure 3. Mixer A Gain vs. Frequency and Supply Voltage Figure 4. Mixer A Gain vs. Frequency and Temperature 12.0 11.5 11.0 10.5 –3 dBm 0 dBm +3 dBm 12.0 11.5 11.0 10.5 4.75 V 5.00 V 5.25 V Gain (dB) Gain (dB) 10.0 9.5 9.0 8.5 8.0 7.5 7.0 328 336 344 352 360 368 376 384 10.0 9.5 9.0 8.5 8.0 7.5 7.0 328 336 344 352 360 368 376 384 RF Frequency (MHz) RF Frequency (MHz) Figure 5. Mixer A Gain vs. Frequency and LO Power Figure 6. Mixer B Gain vs. Frequency and Supply Voltage Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 200884F • Skyworks Proprietary and Confidential information • Products and Product Information are Subject to Change Without Notice • April 3, 2009 5 DATA SHEET • SKY73084-11 DOWNCONVERSION MIXER 12.0 11.5 11.0 10.5 –40 oC +25 oC +85 oC 12.0 11.5 11.0 10.5 –3 dBm 0 dBm +3 dBm Gain (dB) 9.5 9.0 8.5 8.0 7.5 7.0 328 336 344 352 360 368 376 384 Gain (dB) 10.0 10.0 9.5 9.0 8.5 8.0 7.5 7.0 328 336 344 352 360 368 376 384 RF Frequency (MHz) RF Frequency (MHz) Figure 7. Mixer B Gain vs. Frequency and Temperature Figure 8. Mixer B Gain vs. Frequency and LO Power 15 14 13 4.75 V 5.00 V 5.25 V 15 14 13 –40 oC +25 oC +85 oC Noise Figure (dB) Noise Figure (dB) 12 11 10 9 8 7 6 5 328 336 344 352 360 368 376 384 12 11 10 9 8 7 6 5 328 336 344 352 360 368 376 384 RF Frequency (MHz) RF Frequency (MHz) Figure 9. Mixer A Noise Figure vs Frequency and Supply Voltage Figure 10. Mixer A Noise Figure vs Frequency and Temperature 15 14 13 –3 dBm 0 dBm +3 dBm 15 14 13 4.75 V 5.00 V 5.25 V Noise Figure (dB) Noise Figure (dB) 12 11 10 9 8 7 6 5 328 336 344 352 360 368 376 384 12 11 10 9 8 7 6 5 328 336 344 352 360 368 376 384 RF Frequency (MHz) RF Frequency (MHz) Figure 11. Mixer A Noise Figure vs Frequency and LO Power Figure 12. Mixer B Noise Figure vs Frequency and Supply Voltage 15 14 13 –40 oC +25 oC +85 oC 15 14 13 –3 dBm 0 dBm +3 dBm Noise Figure (dB) 12 11 10 9 8 7 6 5 328 336 344 352 360 368 376 384 Noise Figure (dB) 12 11 10 9 8 7 6 5 328 336 344 352 360 368 376 384 RF Frequency (MHz) RF Frequency (MHz) Figure 13. Mixer B Noise Figure vs Frequency and Temperature Figure 14. Mixer B Noise Figure vs Frequency and LO Power Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 6 April 3, 2009 • Skyworks Proprietary and Confidential information • Products and Product Information are Subject to Change Without Notice • 200884F DATA SHEET • SKY73084-11 DOWNCONVERSION MIXER 30 29 28 27 4.75 V 5.00 V 5.25 V 30 29 28 27 –40 oC +25 oC +85 oC IIP3 (dBm) IIP3 (dBm) 26 25 24 23 22 21 20 328 336 344 352 360 368 376 384 26 25 24 23 22 21 20 328 336 344 352 360 368 376 384 RF Frequency (MHz) RF Frequency (MHz) Figure 15. Mixer A IIP3 vs Frequency and Supply Voltage Figure 16. Mixer A IIP3 vs Frequency and Temperature 30 29 28 27 –3 dBm 0 dBm +3 dBm 30 29 28 27 4.75 V 5.00 V 5.25 V IIP3 (dBm) IIP3 (dBm) 26 25 24 23 22 21 20 328 336 344 352 360 368 376 384 26 25 24 23 22 21 20 328 336 344 352 360 368 376 384 RF Frequency (MHz) RF Frequency (MHz) Figure 17. Mixer A IIP3 vs Frequency and LO Power Figure 18. Mixer B IIP3 vs Frequency and Supply Voltage 30 29 28 27 –40 oC +25 oC +85 oC 30 29 28 27 –3 dBm 0 dBm +3 dBm IIP3 (dBm) IIP3 (dBm) 26 25 24 23 22 21 20 328 336 344 352 360 368 376 384 26 25 24 23 22 21 20 328 336 344 352 360 368 376 384 RF Frequency (MHz) RF Frequency (MHz) Figure 19. Mixer B IIP3 vs Frequency and Temperature Figure 20. Mixer B IIP3 vs Frequency and LO Power –60 –61 –62 –60 –61 –62 –40 oC +25 oC +85 oC 2RF – 2 LO (dBc) –40 oC +25 oC +85 oC 2RF – 2 LO (dBc) –63 –64 –65 –66 –67 –68 –69 –70 70 75 80 85 90 95 100 105 110 115 –63 –64 –65 –66 –67 –68 –69 –70 70 75 80 85 90 95 100 105 110 115 IF Frequency (MHz) IF Frequency (MHz) Figure 21. Mixer A 2RF–2LO vs IF Frequency and Temperature Figure 22. Mixer B 2RF–2LO vs IF Frequency and Temperature Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 200884F • Skyworks Proprietary and Confidential information • Products and Product Information are Subject to Change Without Notice • April 3, 2009 7 DATA SHEET • SKY73084-11 DOWNCONVERSION MIXER 90 87 –40 oC +25 oC +85 oC 90 87 –40 oC +25 oC +85 oC RF to IF Isolation (dB) 84 81 78 75 72 69 66 63 60 4.75 5.00 5.25 RF to IF Isolation (dB) 84 81 78 75 72 69 66 63 60 4.75 5.00 5.25 Supply Voltage (V) Supply Voltage (V) Figure 23. Mixer A RF to IF Isolation vs Supply Voltage and Temperature –30 –32 –40 oC +25 oC +85 oC Figure 24. Mixer B RF to IF Isolation vs Supply Voltage and Temperature –30 –32 –40 oC +25 oC +85 oC LO to IF Leakage (dBm) –36 –38 –40 –42 –44 –46 –48 –50 70 75 80 85 90 95 100 105 110 115 LO to IF Leakage (dBm) –34 –34 –36 –38 –40 –42 –44 –46 –48 –50 70 75 80 85 90 95 100 105 110 115 IF Frequency (MHz) IF Frequency (MHz) Figure 25. Mixer A LO to IF Leakage vs IF Frequency and Temperature –30 –32 –40 oC +25 oC +85 oC Figure 26. Mixer B LO to IF Leakage vs IF Frequency and Temperature –30 –32 –40 oC +25 oC +85 oC LO to RF Leakage (dBm) –34 –36 –38 –40 –42 –44 –46 –48 –50 70 75 80 85 90 95 100 105 LO to RF Leakage (dBm) –34 –36 –38 –40 –42 –44 –46 –48 –50 70 75 80 85 90 95 100 105 110 115 110 115 IF Frequency (MHz) IF Frequency (MHz) Figure 27. Mixer A LO to RF Leakage vs IF Frequency and Temperature Channel A to Channel B Isolation (dB) 50 48 46 44 42 40 38 36 34 32 30 4.75 5.00 5.25 –40 oC +25 oC +85 oC Figure 28. Mixer B LO to RF Leakage vs IF Frequency and Temperature –90 –93 –40 oC +25 oC +85 oC Mixer A 4RF-3LO (dBc) –96 –99 –102 –105 –108 –111 –114 –117 –120 4.75 5.00 5.25 Supply Voltage (V) Supply Voltage (V) Figure 29. Channel A to Channel B IF Isolation vs Supply Voltage and Temperature Figure 30. Mixer A 4RF to 3LO vs Supply Voltage and Temperature Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 8 April 3, 2009 • Skyworks Proprietary and Confidential information • Products and Product Information are Subject to Change Without Notice • 200884F DATA SHEET • SKY73084-11 DOWNCONVERSION MIXER –90 –93 –40 oC +25 oC +85 oC Mixer B 4RF-3LO (dBc) –96 –99 –102 –105 –108 –111 –114 –117 –120 4.75 5.00 5.25 Supply Voltage (V) Figure 31. Mixer B 4RF to 3LO vs Supply Voltage and Temperature Evaluation Board Description The SKY73084-11 Evaluation Board is used to test the performance of the SKY73084-11 downconversion mixer. An assembly drawing for the Evaluation Board is shown in Figure 32 and the layer detail is provided in Figure 33. A schematic diagram of the SKY73084-11 Evaluation Board is shown in Figure 34. Circuit Design Configurations The following design considerations are general in nature and must be followed regardless of final use or configuration: 1. Paths to ground should be made as short as possible. 2. The ground pad of the SKY73084-11 has special electrical and thermal grounding requirements. This pad is the main thermal conduit for heat dissipation. Since the circuit board acts as the heat sink, it must shunt as much heat as possible from the device. Therefore, design the connection to the ground pad to dissipate the maximum wattage produced by the circuit board. 3. Skyworks recommends including external bypass capacitors on the VCC voltage inputs of the device. 4. Components L5, L6, L14, and L15 (see Figure 34) are high-Q low loss inductors. These inductors must be able to pass currents in excess of 200 mA DC. 5. Components R1 and R2 (see Figure 34) set the bias current for the IF amplifiers. Skyworks recommends that these resistors have a tolerance of ±1% to optimize performance consistency of the SKY73084-11. These resistors are not required for the Evaluation Board to operate as specified in Tables 3 and 4. Package Dimensions The PCB layout footprint for the SKY73084-11 is provided in Figure 35. Figure 36 shows the package dimensions for the 36-pin MCM and Figure 37 provides the tape and reel dimensions. Package and Handling Information Since the device package is sensitive to moisture absorption, it is baked and vacuum packed before shipping. Instructions on the shipping container label regarding exposure to moisture after the container seal is broken must be followed. Otherwise, problems related to moisture absorption may occur when the part is subjected to high temperature during solder assembly. THE SKY73084-11 is rated to Moisture Sensitivity Level 3 (MSL3) at 260 °C. It can be used for lead or lead-free soldering. For additional information, refer to the Skyworks Application Note, PCB Design & SMT Assembly/Rework Guidelines for MCM-L Packages, document number 101752. Care must be taken when attaching this product, whether it is done manually or in a production solder reflow environment. Production quantities of this product are shipped in a standard tape and reel format. For packaging details, refer to the Skyworks Application Note, Tape and Reel, document number 101568. Electrostatic Discharge (ESD) Sensitivity The SKY73084-11 is a static-sensitive electronic device. Do not operate or store near strong electrostatic fields. Take proper ESD precautions. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 200884F • Skyworks Proprietary and Confidential information • Products and Product Information are Subject to Change Without Notice • April 3, 2009 9 DATA SHEET • SKY73084-11 DOWNCONVERSION MIXER J9 J5 C34 L16 L17 C35 R4 T2 C29 L13 C33 C28 L12 C25 J4 L1 C2 L2 C32 J8 C26 C39 R2 C24 L11 R5 L14 C3 C38 C1 L15 C27 C23 C4 C20 C21 C22 J1 C5 C8 C7 C41 C6 L3 L4 J2 C17 R6 R1 C40 C13 C12 R3 T1 C11 C19 C18 L10 L5 L6 C14 J7 L18 C36 L19 J3 L8 C37 C15 L9 C16 J10 J6 S905 Figure 32. SKY73084-11 Evaluation Board Assembly Diagram Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 10 April 3, 2009 • Skyworks Proprietary and Confidential information • Products and Product Information are Subject to Change Without Notice • 200884F DATA SHEET • SKY73084-11 DOWNCONVERSION MIXER Layer 1: Top -- Metal Layer 2: Ground Layer 3: Power Plane Layer 4: Solid Ground Plane S904 Figure 33. SKY77024 Evaluation Board Layer Detail Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 200884F • Skyworks Proprietary and Confidential information • Products and Product Information are Subject to Change Without Notice • April 3, 2009 11 DATA SHEET • SKY73084-11 DOWNCONVERSION MIXER R4 0Ω DB714 L14 470 nH T2 L13 39 nH C28 33 pF C26 1 μF C27 33 pF L12 0Ω J5 VCC L15 470 nH VCC R2 DNI VCC 36 35 x 34 33 32 31 x 30 29 28 27 26 25 Element Jumper 24 23 22 21 20 19 C17 33 pF R1 DNI L10 0Ω C21 33 pF C22 12 pF C20 1 μF C23 33 pF L11 0Ω x VCC7 IFA+ GND VCC6 NC NC IFA– 1 RIFA NC J4 L1 0Ω L2 5.1 pF C2 27 nH C1 0Ω J8 RFA NC LO2 GND GND GND x 2 3 GND VCC1 GND VCC2 GND NC VCC3 VCC4 VCC 4 C35 33 pF 5 6 7 VCC VCC SKY73084 LO_SEL GND VCC5 GND J7 L3 0Ω C6 27 nH L4 5.1 pF C8 0Ω x 8 9 J3 RFB IFB+ LO1 RIFB 17 18 IFB– GND NC 10 11 12 13 14 15 NC 16 x x VCC L5 470 nH C13 1 μF C14 33 pF x NC VCC L9 0Ω L8 39 nH C16 33 pF VCC L6 470 nH T1 DB714 R3 0Ω J6 Note: The SKY73084 Evaluation Board can be converted to provide a differential output by removing components T1, T2, R3, and R4. Some component labels may be different than the corresponding component symbol shown here. Component values, however, are accurate as of the date of this Data Sheet. S1237 Figure 34. SKY73084-11 Evaluation Board Schematic Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 12 April 3, 2009 • Skyworks Proprietary and Confidential information • Products and Product Information are Subject to Change Without Notice • 200884F DATA SHEET • SKY73084-11 DOWNCONVERSION MIXER 6.3 Component Outline 0.15 0.4 0.25 0.075 0.075 0.75 0.9 12X 0.062 6.3 36X 0.875 Soldermask Opening 24X 0.125 Stencil aperture size for center ground pads should be 80% to 100% (by area) of the solder mask opening of the package. 24X 0.125 36X 0.875 SMT Pad Detail Scale: 2X 9X This Rotation 9X Rotated 180o 9X Rotated 90o CW 9X Rotated 90o CCW Component Outline Stencil and Metallization 12X 0.063 Stencil Aperture Top View 6.3 Pin 36 2X 2.775 Pin 1 6.45 2X 2.775 6.3 0.5 Pitch Typ 6.45 3.88 Component Outline Component Outline 0.25 Typ Thermal Via Array. Solder Mask Opening ∅0.3 mm on 0.6 mm pitch. Top View Additional vias in common ground pad will improve thermal and electrical performance. NOTE: thermal vias should be tented and filled with solder mask, 30-35 μm Cu plating recommended. Metallization Top View Note: The cross-hatched area represents the merger of the center ground pad +10 individual I/O ground pads. All I/O ground pads should have at least one via connected to internal ground planes for optimum electrical performance. All measurements are in millimeters S1125 Figure 35. PCB Layout Footprint for the SKY73084-11 6 x 6 mm MCM Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 200884F • Skyworks Proprietary and Confidential information • Products and Product Information are Subject to Change Without Notice • April 3, 2009 13 DATA SHEET • SKY73084-11 DOWNCONVERSION MIXER 18X 2.9 Pin 1 Indicator 4X 2 Pin 36 4X 0.5 4X 1 C 6 B 4X 1.5 Pin 1 Indicator (See Detail D) Pin 1 A 4X 1 4X 1.5 4X 2 6 4X 0.5 2X 1.9 18X 2.9 36x SMT Pad 0.15 A B C 1.1 ± 0.1 0.15 A B C A 0.1 3X R0.2 2X 1.9 Top View 0.5 ± 0.1 (0.1) Side View 0.2 x 0.2 Bottom View Solder Mask Opening 0.2 A B C 0.25 ± 0.05 0.4 ± 0.05 Detail D Metal Pad Edge All measurements are in millimeters Pads are solder mask defined on one edge and metal defined on three edges. Dimensioning and tolerancing according to ASME Y14.5M-1994 S689_A Detail A Figure 36. SKY73084-11 36-Pin MCM Package Dimensions Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 14 April 3, 2009 • Skyworks Proprietary and Confidential information • Products and Product Information are Subject to Change Without Notice • 200884F DATA SHEET • SKY73084-11 DOWNCONVERSION MIXER 2.00 ± 0.05 ∅1.50 ± 0.10 0.30 ± 0.02 Pin #1 Indicator (see Notes) 8.00 4.00 B 1.75 ± 0.10 5.50 ± 0.05 A 6.35 A 7o Max. 1.59 B ∅1.50 Min. 6.35 B Notes: 1. Carrier tape: black conductive polystyrene 2. Cover tape material: transparent conductive PSA 3. Cover tape size: 9.3 mm width 4. All dimensions are in millimeters 5. Pin 1 orientation is in top left corner for the following Skyworks products: SKY73022-21, -31 SKY73023-21, -31 For all other 6 x 6 mm MCM/RFLGA products, pin 1 orientation is in top right corner. 8 Max. o A S1183 Figure 37. SKY73084-11 Tape and Reel Dimensions Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 200884F • Skyworks Proprietary and Confidential information • Products and Product Information are Subject to Change Without Notice • April 3, 2009 15 12.00 ± 0.30 DATA SHEET • SKY73084-11 DOWNCONVERSION MIXER Ordering Information Model Name SKY73084-11 300-500 MHz Downconversion Mixer Manufacturing Part Number SKY73084-11 (Pb-free package) Evaluation Kit Part Number TW17-D570 Copyright © 2008, 2009 Skyworks Solutions, Inc. All Rights Reserved. Information in this document is provided in connection with Skyworks Solutions, Inc. (“Skyworks”) products or services. These materials, including the information contained herein, are provided by Skyworks as a service to its customers and may be used for informational purposes only by the customer. Skyworks assumes no responsibility for errors or omissions in these materials or the information contained herein. Skyworks may change its documentation, products, services, specifications or product descriptions at any time, without notice. Skyworks makes no commitment to update the materials or information and shall have no responsibility whatsoever for conflicts, incompatibilities, or other difficulties arising from any future changes. No license, whether express, implied, by estoppel or otherwise, is granted to any intellectual property rights by this document. Skyworks assumes no liability for any materials, products or information provided hereunder, including the sale, distribution, reproduction or use of Skyworks products, information or materials, except as may be provided in Skyworks Terms and Conditions of Sale. THE MATERIALS, PRODUCTS AND INFORMATION ARE PROVIDED “AS IS” WITHOUT WARRANTY OF ANY KIND, WHETHER EXPRESS, IMPLIED, STATUTORY, OR OTHERWISE, INCLUDING FITNESS FOR A PARTICULAR PURPOSE OR USE, MERCHANTABILITY, PERFORMANCE, QUALITY OR NON-INFRINGEMENT OF ANY INTELLECTUAL PROPERTY RIGHT; ALL SUCH WARRANTIES ARE HEREBY EXPRESSLY DISCLAIMED. SKYWORKS DOES NOT WARRANT THE ACCURACY OR COMPLETENESS OF THE INFORMATION, TEXT, GRAPHICS OR OTHER ITEMS CONTAINED WITHIN THESE MATERIALS. SKYWORKS SHALL NOT BE LIABLE FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO ANY SPECIAL, INDIRECT, INCIDENTAL, STATUTORY, OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION, LOST REVENUES OR LOST PROFITS THAT MAY RESULT FROM THE USE OF THE MATERIALS OR INFORMATION, WHETHER OR NOT THE RECIPIENT OF MATERIALS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Skyworks products are not intended for use in medical, lifesaving or life-sustaining applications, or other equipment in which the failure of the Skyworks products could lead to personal injury, death, physical or environmental damage. Skyworks customers using or selling Skyworks products for use in such applications do so at their own risk and agree to fully indemnify Skyworks for any damages resulting from such improper use or sale. Customers are responsible for their products and applications using Skyworks products, which may deviate from published specifications as a result of design defects, errors, or operation of products outside of published parameters or design specifications. Customers should include design and operating safeguards to minimize these and other risks. Skyworks assumes no liability for applications assistance, customer product design, or damage to any equipment resulting from the use of Skyworks products outside of stated published specifications or parameters. Skyworks, the Skyworks symbol, and “Breakthrough Simplicity” are trademarks or registered trademarks of Skyworks Solutions, Inc., in the United States and other countries. Third-party brands and names are for identification purposes only, and are the property of their respective owners. Additional information, including relevant terms and conditions, posted at www.skyworksinc.com, are incorporated by reference. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 16 April 3, 2009 • Skyworks Proprietary and Confidential information • Products and Product Information are Subject to Change Without Notice • 200884F