SKYFR-001439

SPECIFICATION SHEET SKYFR-001439: 2300—2400 MHz Single Junc#on Robust Lead Isolator Applica#ons • Wireless infrastructure • Power amplifiers Features • Small surface mount package • Operang frequency range: 2300 to 2400 MHz • BeO free • RoHS compliant • Tape & Reel 1 CW 2 Figure 1. Block Diagram Table 1. Absolute Maximum Ratings Parameter Symbol Test Condition Min Max Units Average power PAVG 20 W Peak power PPK 100 W Operating temperature range TOP -40 +125 °C TSTOR -55 +125 °C Storage temperature range Note: Exceeding any of the limits listed here may result in permanent damage to the device or may reduce device reliability. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com Revision 1 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • July 2017 1 SPECIFICATION SHEET • SKYFR-001439 Table 2. Electrical Specifications (Note 1) Parameter Symbol Frequency range Test Condition f Min Typical 2300 Impedance Max Units 2400 MHz 50 @ IL -40°C to +125°C Isolation ISO -40°C to +125°C 20 dB Return loss RL -40°C to +125°C 20 dB Insertion loss 0.25 Group delay 2.0 Intermodulation distortion (Note 2) IMD 2 x 5W CW tones, 1MHz spacing 55 dB ns dBc Note 1: Performance is guaranteed under the conditions listed in this table and over the operating temperature range. Note 2: See Skyworks Application Note, Intermodulation Distortion Measurements of Ferrites, document number 201537 for further details. Note 3: Part tested on PCB-00167, 0.508mm Rogers RO4350B, trace width 1.07mm wide, 1oz copper. Table 3. Plating Specification Section Base Material Plating Pins Brass Silver Housing Steel Silver Table 4. Ordering Information Manufacturing Part Number SKYFR-001439 Evaluation Board Part Number TFX-00118 Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 2017 2 SPECIFICATION SHEET • SKYFR-001439 All dimensions in millimeters. Tolerance: ±0.2mm unless otherwise specified. Coplanarity specification: 0.1mm maximum. Figure 2. Package Dimensions and Recommended PCB Layout Copyright © 2011 Skyworks Solutions, Inc. All Rights Reserved. Information in the document is provided in connection with Skyworks Solutions, Inc. (“Skyworks”) products or services. These materials, including the information contained herein, are provided by Skyworks as a service to its customers and may be used for informational purposes only by the customer. Skyworks assumes no responsibility for errors or omissions in these materials or the information contained herein. Skyworks may change its documentation, products, services, specifications or product descriptions at any time, without notice. Skyworks makes no commitment to update the materials or information and shall have no responsibility whatsoever for conflicts, incompatibilities, or other difficulties arising from any future changes. No license, whether express, implied, by estoppel or otherwise, is granted to any intellectual property rights by this document. Skyworks assumes no liability for any materials, products or information provided hereunder, including the sale, distribution, reproduction or use of any Skyworks products, information or materials, except as may be provided in Skyworks Terms and Conditions of Sale. THE MATERIALS, PRODUCTS AND INFORMATION ARE PROVIDED “AS IS” WITHOUT WARRANTY OF ANY KIND, WHETHER EXPRESS, IMPLIED, STATUTORY, OR OTHERWISE, INCLUDING FITNESS FOR A PARTICULAR PURPOSE OR USE, MERCHANTABILITY, PERFORMANCE, QUALITY OR NON-INFRIDGEMENT OF ANY INTELLECTUAL PROPERTY RIGHT; ALL SUCH WARRANTIES ARE HEREBY EXPRESSLY DISCLAIMED. SKYWORKS DOES NOT WARRANT THE ACCURACY OR COMPLETENESS OF THE INFORMATION, TEXT, GRAPHICS OR OTHER ITEMS CONTAINED WITHIN THESE MATERIALS. SKYWORKS SHALL NOT BE LIABLE FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO ANY SPECIAL, INDIRECT, INCIDENTAL, STATUTORY, OR CONSEQUENCIAL DAMAGES, INCLUDING WITHOUT LIMITATION, LOST REVENUES OR LOST PROFITS THAT MAY RESULT FROM THE USE OF THE MATERIALS OR INFORMATION, WHETHER OR NOT THE RECIPIENT OF MATERIALS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Skyworks products are not intended for use in medical, lifesaving or life-sustaining applications, or other equipment in which the failure of the Skyworks products could lead to personal injury, death, physical or environmental damage. Skyworks customers using or selling Skyworks products for use in such applications do so at their own risk and agree to fully indemnify Skyworks for any damages resulting from such improper use or sale. Customers are responsible for their products and applications using Skyworks products, which may deviate from published specifications as a result of design defects, errors, or operation of products outside of published parameters or design specifications. Customers should include design and operating safeguards to minimize these and other risks. Skyworks assumes no liability for applications assistance, customer product design, or damage to any equipment resulting from the use of Skyworks products outside of stated published specifications or parameters. Skyworks, the Skyworks symbol, and “Breakthrough Simplicity” are trademarks or registered trademarks of Skyworks Solutions, Inc. in the United States and other countries. Third-party brands and names are for identification purposes only, and are the property of their respective owners. Additional information, including relevant terms and conditions, posted at www.skyworksinc.com and incorporated by reference. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 2017 3