SL74HC151D

SL74HC151 8-Input Data Selector/Multiplexer High-Performance Silicon-Gate CMOS The SL74HC151 is identical in pinout to the LS/ALS151. The device inputs are compatible with standard CMOS outputs; with pullup resistors, they are compatible with LS/ALSTTL outputs. The device selects one of the eight binary Data Inputs, as determined by the Address Inputs. The Strobe pin must be at a low level for the selected data to appear at the outputs. If Strobe is high, the Y output is forced to a low level and the Y output is forced to a high level. • Outputs Directly Interface to CMOS, NMOS, and TTL • Operating Voltage Range: 2.0 to 6.0 V • Low Input Current: 1.0 µA • High Noise Immunity Characteristic of CMOS Devices ORDERING INFORMATION SL74HC151N Plastic SL74HC151D SOIC TA = -55° to 125° C for all packages PIN ASSIGNMENT LOGIC DIAGRAM FUNCTION TABLE Inputs A2 X L L PIN 16 =VCC PIN 8 = GND L L H H H H A1 X L L H H L L H H A0 X L H L H L H L H Strobe H L L L L L L L L Outputs Y L D0 D1 D2 D3 D4 D5 D6 D7 Y H D0 D1 D2 D3 D4 D5 D6 D7 D0,D1...D7=the level of the respective D input X = don’t care SLS System Logic Semiconductor SL74HC151 MAXIMUM RATINGS * Symbol VCC VIN VOUT IIN IOUT ICC PD T stg TL * Parameter DC Supply Voltage (Referenced to GND) DC Input Voltage (Referenced to GND) DC Output Voltage (Referenced to GND) DC Input Current, per Pin DC Output Current, per Pin DC Supply Current, VCC and GND Pins Power Dissipation in Still Air, Plastic DIP+ SOIC Package+ Storage Temperature Lead Temperature, 1 mm from Case for 10 Seconds (Plastic DIP or SOIC Package) Value -0.5 to +7.0 -1.5 to VCC +1.5 -0.5 to VCC +0.5 ±20 ±25 ±50 750 500 -65 to +150 260 Unit V V V mA mA mA mW °C °C Maximum Ratings are those values beyond which damage to the device may occur. Functional operation should be restricted to the Recommended Operating Conditions. +Derating - Plastic DIP: - 10 mW/°C from 65° to 125°C SOIC Package: : - 7 mW/°C from 65° to 125°C RECOMMENDED OPERATING CONDITIONS Symbol VCC VIN, VOUT TA tr, t f Parameter DC Supply Voltage (Referenced to GND) DC Input Voltage, Output Voltage (Referenced to GND) Operating Temperature, All Package Types Input Rise and Fall Time (Figure 1) VCC =2.0 V VCC =4.5 V VCC =6.0 V Min 2.0 0 -55 0 0 0 Max 6.0 VCC +125 1000 500 400 Unit V V °C ns This device contains protection circuitry to guard against damage due to high static voltages or electric fields. However, precautions must be taken to avoid applications of any voltage higher than maximum rated voltages to this high-impedance circuit. For proper operation, VIN a nd VOUT should be constrained to the range GND≤(VIN or VOUT)≤VCC. Unused inputs must always be tied to an appropriate logic voltage level (e.g., either GND or V ). CC Unused outputs must be left open. SLS System Logic Semiconductor SL74HC151 DC ELECTRICAL CHARACTERISTICS (Voltages Referenced to GND) VCC Symbol Parameter Test Conditions V Guaranteed Limit 25 °C to -55°C 1.5 3.15 4.2 0.3 0.9 1.2 1.9 4.4 5.9 3.98 5.48 0.1 0.1 0.1 0.26 0.26 ±0.1 8.0 ≤85 °C 1.5 3.15 4.2 0.3 0.9 1.2 1.9 4.4 5.9 3.84 5.34 0.1 0.1 0.1 0.33 0.33 ±1.0 80 ≤125 °C 1.5 3.15 4.2 0.3 0.9 1.2 1.9 4.4 5.9 3.7 5.2 0.1 0.1 0.1 0.4 0.4 ±1.0 160 µA µA V Unit VIH Minimum High-Level Input Voltage Maximum Low -Level Input Voltage Minimum High-Level Output Voltage VOUT=0.1 V or VCC-0.1 V IOUT≤ 20 µA VOUT=0.1 V or VCC-0.1 V IOUT ≤ 20 µA VIN=VIH or VIL IOUT ≤ 20 µA VIN=VIH or VIL IOUT ≤ 4.0 mA IOUT ≤ 5.2 mA 2.0 4.5 6.0 2.0 4.5 6.0 2.0 4.5 6.0 4.5 6.0 2.0 4.5 6.0 4.5 6.0 6.0 6.0 V VIL V VOH V VOL Maximum Low-Level Output Voltage VIN=VIH or VIL IOUT ≤ 20 µA VIN=VIH or VIL IOUT ≤ 4.0 mA IOUT ≤ 5.2 mA IIN ICC Maximum Input Leakage Current Maximum Quiescent Supply Current (per Package) VIN=VCC or GND VIN=VCC or GND IOUT=0µA SLS System Logic Semiconductor SL74HC151 AC ELECTRICAL CHARACTERISTICS (CL=50pF,Input t r=t f=6.0 ns) VCC Symbol tPLH, t PHL Parameter Maximum Propagation Delay, Input D to Output Y or Y (Figures 1,3 and 6) Maximum Propagation Delay , Input A to Output Y or Y (Figures 2 and 6) Maximum Propagation Delay , Strobe to Output Y or Y (Figures 4,5 and 6) Maximum Output Transition Time, Any Output (Figures 1 and 6) Maximum Input Capacitance Power Dissipation Capacitance (Per Package) CPD Used to determine the no-load dynamic power consumption: PD=CPDVCC2f+ICCVCC V 2.0 4.5 6.0 2.0 4.5 6.0 2.0 4.5 6.0 2.0 4.5 6.0 Guaranteed Limit 25 °C to -55°C 185 37 31 205 41 35 125 25 21 75 15 13 10 ≤85°C 230 46 39 255 51 43 155 31 26 95 19 16 10 ≤125°C 280 56 48 310 62 53 190 38 32 110 22 19 10 Unit ns tPLH, t PHL ns tPLH, t PHL ns tTLH, t THL ns CIN pF Typical @25°C,VCC=5.0 V 36 pF Figure 1. Switching Waveforms Figure 2. Switching Waveforms Figure 3. Switching Waveforms Figure 4. Switching Waveforms SLS System Logic Semiconductor SL74HC151 Figure 5. Switching waveforms Figure 6.Test Circuit EXPANDED LOGIC DIAGRAM SLS System Logic Semiconductor