USB3311-CP-TR

USB3311 Hi-Speed USB Transceiver with 1.8V ULPI Interface 26MHz Reference Clock PRODUCT FEATURES USB-IF “Hi-Speed” compliant to the Universal Serial Bus Specification Rev 2.0 Interface compliant with the ULPI Specification revision 1.1 as a Single Data Rate (SDR) PHY 1.8V IO Voltage (+/- 10%) SMSC flexPWRTM Technology — Low current design ideal for battery powered applications — “Sleep” mode tri-states all ULPI pins and places the part in a low current state Data Brief Carkit UART mode for non-USB serial data transfers Integrated USB Switch — — — — — Allows single USB port of connection High speed data Battery charging Stereo and mono/mic audio USB1.1 data Industrial Operating Temperature -40°C to +85°C Packaging Options — 24 pin QFN lead-free RoHS compliant package (4 x 4 x 0.90 mm height) — 25 ball VFBGA lead-free RoHS compliant package also available; (3 x 3 x 0.88mm height) Supports FS pre-amble for FS hubs with a LS device attached (UTMI+ Level 3) Supports HS SOF and LS keep-alive pulse Includes full support for the optional On-The-Go (OTG) protocol detailed in the On-The-Go Supplement Revision 1.0a specification Supports the OTG Host Negotiation Protocol (HNP) and Session Request Protocol (SRP) Allows host to turn VBUS off to conserve battery power in OTG applications Support OTG monitoring of VBUS levels with internal comparators “Wrapper-less” design for optimal timing performance and design ease — Low Latency Hi-Speed Receiver (43 Hi-Speed clocks Max) allows use of legacy UTMI Links with a ULPI bridge Applications The USB3311 is targeted for any application where a HiSpeed USB connection is desired and when board space, power, and interface pins must be minimized. The USB3311 is well suited for: Cell Phones PDAs MP3 Players GPS Personal Navigation Scanners External Hard Drives Digital Still and Video Cameras Portable Media Players Entertainment Devices Printers Set Top Boxes Video Record/Playback Systems IP and Video Phones Gaming Consoles POS Terminals Internal 5V cable short-circuit protection of ID, DP and DM lines to VBUS or ground 26MHz Reference Clock operation — 0 to 3.6V input drive tolerant — Able to accept “noisy” clock sources Internal low jitter PLL for 480MHz Hi-Speed USB operation Internal detection of the value of resistance to ground on the ID pin Integrated battery to 3.3V LDO regulator — 2.2uF bypass capacitor — 100mV dropout voltage Integrated ESD protection circuits — Up to +-15kV without any external devices SMSC USB3311 PRODUCT PREVIEW Revision 1.0 (05-08-07) Hi-Speed USB Transceiver with 1.8V ULPI Interface - 26MHz Reference Clock ORDER NUMBER(S): USB3311-CP-TR for 24 pin, QFN Lead-Free RoHS Compliant Package (tape and reel) USB3311-GJ-TR for 25 pin, VFBGA Lead-Free RoHS Compliant Package (tape and reel) Reel size is 4000 pieces. 80 ARKAY DRIVE, HAUPPAUGE, NY 11788 (631) 435-6000, FAX (631) 273-3123 Copyright © 2007 SMSC or its subsidiaries. All rights reserved. Circuit diagrams and other information relating to SMSC products are included as a means of illustrating typical applications. Consequently, complete information sufficient for construction purposes is not necessarily given. Although the information has been checked and is believed to be accurate, no responsibility is assumed for inaccuracies. SMSC reserves the right to make changes to specifications and product descriptions at any time without notice. Contact your local SMSC sales office to obtain the latest specifications before placing your product order. The provision of this information does not convey to the purchaser of the described semiconductor devices any licenses under any patent rights or other intellectual property rights of SMSC or others. All sales are expressly conditional on your agreement to the terms and conditions of the most recently dated version of SMSC's standard Terms of Sale Agreement dated before the date of your order (the "Terms of Sale Agreement"). The product may contain design defects or errors known as anomalies which may cause the product's functions to deviate from published specifications. Anomaly sheets are available upon request. SMSC products are not designed, intended, authorized or warranted for use in any life support or other application where product failure could cause or contribute to personal injury or severe property damage. Any and all such uses without prior written approval of an Officer of SMSC and further testing and/or modification will be fully at the risk of the customer. Copies of this document or other SMSC literature, as well as the Terms of Sale Agreement, may be obtained by visiting SMSC’s website at http://www.smsc.com. SMSC is a registered trademark of Standard Microsystems Corporation (“SMSC”). Product names and company names are the trademarks of their respective holders. SMSC DISCLAIMS AND EXCLUDES ANY AND ALL WARRANTIES, INCLUDING WITHOUT LIMITATION ANY AND ALL IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, TITLE, AND AGAINST INFRINGEMENT AND THE LIKE, AND ANY AND ALL WARRANTIES ARISING FROM ANY COURSE OF DEALING OR USAGE OF TRADE. IN NO EVENT SHALL SMSC BE LIABLE FOR ANY DIRECT, INCIDENTAL, INDIRECT, SPECIAL, PUNITIVE, OR CONSEQUENTIAL DAMAGES; OR FOR LOST DATA, PROFITS, SAVINGS OR REVENUES OF ANY KIND; REGARDLESS OF THE FORM OF ACTION, WHETHER BASED ON CONTRACT; TORT; NEGLIGENCE OF SMSC OR OTHERS; STRICT LIABILITY; BREACH OF WARRANTY; OR OTHERWISE; WHETHER OR NOT ANY REMEDY OF BUYER IS HELD TO HAVE FAILED OF ITS ESSENTIAL PURPOSE, AND WHETHER OR NOT SMSC HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Revision 1.0 (05-08-07) PRODUCT PREVIEW 2 SMSC USB3311 Hi-Speed USB Transceiver with 1.8V ULPI Interface - 26MHz Reference Clock General Description The USB3311 is a highly integrated Hi-Speed USB2.0 Transceiver (PHY) that supports systems architectures based on a 26MHz reference clock. It is designed to be used in both commercial and industrial temperature applications. The USB3311 meets all of the electrical requirements to be used as a Hi-Speed USB Host, Device, or an On-the-Go (OTG) device. In addition to the supporting USB signaling the USB3311 also provides USB UART mode and USB Audio mode. USB3311 uses the industry standard UTMI+ Low Pin Interface (ULPI) to connect the USB PHY to the Link. The industry standard ULPI interface uses a method of in-band signaling and status byte transfers between the Link and PHY, to facilitate a USB session. By using in-band signaling and status byte transfers the ULPI interface requires only 12 pins. The USB3311 uses SMSC’s “wrapper-less” technology to implement the ULPI interface. This “wrapperless” technology allows the PHY to achieve a low latency transmit and receive time. SMSC’s low latency transceiver allows an existing UTMI Link to be reused by adding a UTMI to ULPI bridge. By adding a bridge to the ASIC the existing and proven UTMI Link IP can be reused. REFCLK VBUS ID ESD Protection OTG Low Jitter Integrated PLL BIAS RBIAS DP DM Hi-Speed USB Transceiver ULPI Registers and State Machine Integrated Power Management RESETB VBAT VDD33 VDD18 Carkit ULPI Interface STP NXT DIR CLKOUT SPKR_L SPKR_R/M DATA[7:0] Figure 1 USB3311 Block Diagram The USB3311 is designed to run with a 26MHz reference clock. By using a reference clock from the Link the USB3311 is able to remove the cost of a crystal reference from the design. SMSC USB3311 PRODUCT PREVIEW 3 Revision 1.0 (05-08-07) Hi-Speed USB Transceiver with 1.8V ULPI Interface - 26MHz Reference Clock The USB3311 includes a integrated 3.3V LDO regulator to generate its own supply from the VBAT pin. The VBAT pin can range from 3.1 to 5.5V. The regulator dropout voltage is less than 100mV which allows the PHY to continue USB signaling when the voltage on VBAT drops to 3.1V. The USB transceiver will continue to operate at lower voltages, although some parameters may be outside the limits of the USB specifications. If the user would like to provide a 3.3V supply to the USB3311 the VBAT and VDD3.3 pins should be connected together. The USB3311 also includes integrated pull-up resistors that can be used for detecting the attachment of a USB Charger. By sensing the attachment to a USB Charger a product using the USB3311 can charge its battery at more than the 500mA allowed when charging from a USB Host. The USB3311 also includes support for USB audio modes. The user can program the PHY into UART or audio mode while in synchronous mode. The USB3311 can only enter these modes when the user programs the part into these modes. In USB UART mode, the USB3311 DP and DM outputs will be redefined to transmit on DM and to receive on DP. In UART mode the USB3311 can function as a bi-directional transceiver. In USB audio mode the DP pin is shorted to the SPKR_R/M pin with a switch. The DM pin is shorted to the SPKR_L pin. The user can then initiate audio signaling over the USB cable. In addition to audio signals, the switches can also be used to connect Full Speed USB from another PHY onto the USB cable. Revision 1.0 (05-08-07) PRODUCT PREVIEW 4 SMSC USB3311 Hi-Speed USB Transceiver with 1.8V ULPI Interface - 26MHz Reference Clock USB3311 Pin Locations and Descriptions Package Diagram with Pin Locations The pinout below is viewed from the top of the package. RESETB REFCLK VDD1.8 RBIAS STP 20 24 23 22 21 19 DIR ID VBUS VBAT VDD3.3 DM DP 1 2 3 4 5 6 10 11 12 7 8 9 18 17 NXT DATA0 DATA1 DATA2 DATA3 CLKOUT 24Pin QFN 4x4mm 16 15 14 13 SPKR_R/M SPKR_L DATA7 DATA6 DATA5 Figure 2 USB3311 QFN Pinout - Top View SMSC USB3311 PRODUCT PREVIEW 5 DATA4 Revision 1.0 (05-08-07) Hi-Speed USB Transceiver with 1.8V ULPI Interface - 26MHz Reference Clock 1 A B C D E 2 3 4 5 TOP VIEW Figure 3 USB3311 VFBGA Pinout - Top View Pin Definitions The following table details the pin definitions for the figure above. Table 1 USB3311 Pin Description PIN/ BALL DIRECTION/ TYPE Input, Analog ID I/O, Analog VBUS Power VBAT N/A N/A ACTIVE LEVEL N/A NAME DESCRIPTION ID pin of the USB cable. For non-OTG applications this pin can be floated. For an A-Device ID is grounded. For a BDevice ID is floated. VBUS pin of the USB cable. This pin is used for the Vbus comparator inputs and for Vbus pulsing during session request protocol. Regulator input. The regulator supply can be from 5.5V to 3.1V. 1 B1 2 C1 3 C2 Revision 1.0 (05-08-07) PRODUCT PREVIEW 6 SMSC USB3311 Hi-Speed USB Transceiver with 1.8V ULPI Interface - 26MHz Reference Clock Table 1 USB3311 Pin Description (continued) PIN/ BALL DIRECTION/ TYPE Power 4 D2 5 D1 6 E1 7 E2 8 E3 9 D3 10 E4 11 D4 12 E5 13 D5 14 C4 15 C5 16 B4 17 B5 ACTIVE LEVEL N/A NAME DESCRIPTION 3.3V Regulator Output. A 2.2uF (