USB3326A-GL-TR

USB332x Miniature Hi-Speed USB Transceiver with 1.8V ULPI Interface PRODUCT FEATURES Integrated ESD protection circuits — Up to ±15kV IEC Air Discharge without external devices Over-Voltage Protection circuit (OVP) protects the VBUS pin from continuous DC voltages up to 30V Integrated USB Switch — No degradation of Hi-Speed electrical characteristics — Allows single USB port of connection by providing switching function for: – Battery charging – Stereo and mono/mic audio – USB Full-Speed/Low-Speed data flexPWRTM Technology — Low current design ideal for battery powered applications — “Sleep” mode tri-states all ULPI pins and places the part in a low current state — 1.8V IO Voltage (±10%) Integrated battery to 3.3V LDO regulator — 2.2uF bypass capacitor — 100mV dropout voltage “Wrapper-less” design for optimal timing performance and design ease — Low Latency Hi-Speed Receiver (43 Hi-Speed clocks Max) allows use of legacy UTMI Links with a ULPI bridge External Reference Clock operation — 0 to 3.6V input drive tolerant — Able to accept “noisy” clock sources as reference to internal, low-jitter PLL — Frequencies: 12, 13, 19.2, 24, 26, 27, 38.4, 52 or 60MHz Smart detection circuits allow identification of USB charger, headset, or data cable insertion Includes full support for the optional On-The-Go (OTG) protocol detailed in the On-The-Go Supplement Revision 1.3 specification Supports the OTG Host Negotiation Protocol (HNP) and Session Request Protocol (SRP) UART mode for non-USB serial data transfers SMSC USB332x Data Brief Internal 5V cable short-circuit protection of ID, DP and DM lines to VBUS or ground Industrial Operating Temperature -40°C to +85°C 25 ball WLCSP lead-free RoHS compliant package; (1.95 x 1.95 x 0.53mm height) Applications The USB332x is targeted for any application where a HiSpeed USB connection is desired and when board space, power, and interface pins must be minimized. The USB332x is well suited for: Cell Phones PDAs MP3 Players GPS Personal Navigation Devices Datacards Scanners External Hard Drives Digital Still and Video Cameras Portable Media Players Entertainment Devices Printers HDTVs Set Top Boxes/DVR/PVR Video Record/Playback Systems IP and Video Phones Gaming Consoles POS Terminals PRODUCT PREVIEW Revision 0.3 (02-04-08) Miniature Hi-Speed USB Transceiver with 1.8V ULPI Interface ORDER NUMBER(S): ORDER NUMBER USB3321A-GL-TR USB3322A-GL-TR USB3324A-GL-TR USB3325A-GL-TR USB3326A-GL-TR USB3327A-GL-TR USB3328A-GL-TR USB3329A-GL-TR Note 1 REFCLK FREQUENCY (NOTE 1) 26MHz 12MHz 52MHz 24MHz 19.2MHz 27MHz 38.4MHz 13MHz PACKAGE TYPE REEL SIZE 25 Ball, WLCSP Lead-Free RoHS Compliant Package (tape and reel) 3000 pieces All versions support ULPI Clock In Mode (60MHz input at REFCLK) 80 ARKAY DRIVE, HAUPPAUGE, NY 11788 (631) 435-6000, FAX (631) 273-3123 Copyright © 2008 SMSC or its subsidiaries. All rights reserved. Circuit diagrams and other information relating to SMSC products are included as a means of illustrating typical applications. Consequently, complete information sufficient for construction purposes is not necessarily given. Although the information has been checked and is believed to be accurate, no responsibility is assumed for inaccuracies. SMSC reserves the right to make changes to specifications and product descriptions at any time without notice. Contact your local SMSC sales office to obtain the latest specifications before placing your product order. The provision of this information does not convey to the purchaser of the described semiconductor devices any licenses under any patent rights or other intellectual property rights of SMSC or others. All sales are expressly conditional on your agreement to the terms and conditions of the most recently dated version of SMSC's standard Terms of Sale Agreement dated before the date of your order (the "Terms of Sale Agreement"). The product may contain design defects or errors known as anomalies which may cause the product's functions to deviate from published specifications. Anomaly sheets are available upon request. SMSC products are not designed, intended, authorized or warranted for use in any life support or other application where product failure could cause or contribute to personal injury or severe property damage. Any and all such uses without prior written approval of an Officer of SMSC and further testing and/or modification will be fully at the risk of the customer. Copies of this document or other SMSC literature, as well as the Terms of Sale Agreement, may be obtained by visiting SMSC’s website at http://www.smsc.com. SMSC is a registered trademark of Standard Microsystems Corporation (“SMSC”). Product names and company names are the trademarks of their respective holders. SMSC DISCLAIMS AND EXCLUDES ANY AND ALL WARRANTIES, INCLUDING WITHOUT LIMITATION ANY AND ALL IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, TITLE, AND AGAINST INFRINGEMENT AND THE LIKE, AND ANY AND ALL WARRANTIES ARISING FROM ANY COURSE OF DEALING OR USAGE OF TRADE. IN NO EVENT SHALL SMSC BE LIABLE FOR ANY DIRECT, INCIDENTAL, INDIRECT, SPECIAL, PUNITIVE, OR CONSEQUENTIAL DAMAGES; OR FOR LOST DATA, PROFITS, SAVINGS OR REVENUES OF ANY KIND; REGARDLESS OF THE FORM OF ACTION, WHETHER BASED ON CONTRACT; TORT; NEGLIGENCE OF SMSC OR OTHERS; STRICT LIABILITY; BREACH OF WARRANTY; OR OTHERWISE; WHETHER OR NOT ANY REMEDY OF BUYER IS HELD TO HAVE FAILED OF ITS ESSENTIAL PURPOSE, AND WHETHER OR NOT SMSC HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Revision 0.3 (02-04-08) 2 SMSC USB332x PRODUCT PREVIEW Miniature Hi-Speed USB Transceiver with 1.8V ULPI Interface General Description SMSC’s USB332x is a family of Hi-Speed USB 2.0 Transceivers that provides a physical layer (PHY) solution well-suited for portable electronic devices. Both commercial and industrial temperature applications are supported. Each model in the USB332x family may use a 60MHz reference clock, or the model-number specific reference clock shown in ORDER NUMBER(S): on page 2. Several advanced features make the USB332x the transceiver of choice by reducing both eBOM part count and printed circuit board (PCB) area. Outstanding ESD robustness eliminates the need for external ESD protection devices in typical applications. The internal Over-Voltage Protection circuit (OVP) protects the USB332x from voltages up to 30V. By using a reference clock from the Link, the USB332x removes the cost of a dedicated crystal reference from the design. And the integrated USB switch enables unique product features with a single USB port of connection. The USB332x meets all of the electrical requirements to be used as a Hi-Speed USB Host, Device, or an On-the-Go (OTG) transceiver. In addition to the supporting USB signaling, the USB332x also provides USB UART mode and USB Audio mode. USB332x uses the industry standard UTMI+ Low Pin Interface (ULPI) to connect the USB PHY to the Link. ULPI uses a method of in-band signaling and status byte transfers between the Link and PHY to facilitate a USB session with only 12 pins. The USB332x uses SMSC’s “wrapper-less” technology to implement the ULPI interface. This “wrapperless” technology allows the PHY to achieve a low latency transmit and receive time. SMSC’s low latency transceiver allows an existing UTMI Link to be reused by adding a UTMI to ULPI bridge. By adding a bridge to the ASIC the existing and proven UTMI Link IP can be reused. REFCLK VBUS OVP ESD Protection OTG ID Low Jitter Integrated PLL BIAS RBIAS DP DM Hi-Speed USB Transceiver Integrated Power Management ULPI Registers and State Machine RESETB VBAT VDD33 VDD18 USB DP/DM Switch ULPI Interface STP NXT DIR CLKOUT SPK_L SPK_R DATA[7:0] Figure 1 USB332x Block Diagram SMSC USB332x 3 Revision 0.3 (02-04-08) PRODUCT PREVIEW Miniature Hi-Speed USB Transceiver with 1.8V ULPI Interface The USB332x includes an integrated 3.3V LDO regulator that may optionally be used to generate 3.3V from power applied at the VBAT pin. The voltage on the VBAT pin can range from 3.1 to 5.5V. The regulator dropout voltage is less than 100mV which allows the PHY to continue USB signaling when the voltage on VBAT drops to 3.1V. The USB transceiver will continue to operate at lower voltages, although some parameters may be outside the limits of the USB specifications. If the user would like to provide a 3.3V supply to the USB332x, the VBAT and VDD33 pins should be connected together. The USB332x also includes integrated pull-up resistors that can be used for detecting the attachment of a USB Charger. By sensing the attachment to a USB Charger, a product using the USB332x can charge its battery at more than the 500mA allowed when charging from a USB Host. In USB UART mode, the USB332x D P a nd DM pins are redefined to enable pass-through of asynchronous serial data. The USB332x can only enter UART mode when the user programs the part into this mode. In USB audio mode, a switch connects the DP pin to the SPK_R pin, and another switch connects he DM pin to the SPK_L pin. The USB332x can be configured to enter USB audio mode. In addition, these switches are on when the RESETB pin of the USB332x is asserted. The USB audio mode enables audio signalling from a single USB port of connection, and the switches may also be used to connect Full Speed USB from another PHY onto the USB cable. Revision 0.3 (02-04-08) 4 SMSC USB332x PRODUCT PREVIEW Miniature Hi-Speed USB Transceiver with 1.8V ULPI Interface USB332x Pin Locations and Descriptions Package Diagram with Ball Locations The illustration below is viewed from the top of the package. 1 A B C D E RBIAS 2 REFCLK 3 STP 4 DIR 5 CLKOUT ID RESETB VDD18 DATA[0] NXT VBAT VBUS GND DATA[2] DATA[1] DM VDD33 DATA[7] DATA[4] DATA[3] DP SPK_R SPK_L DATA[6] DATA[5] TOP VIEW Figure 2 USB332x Ball Locations - Top View Ball Definitions The following table details the ball definitions for the figure above. Table 1 USB332x Pin Description DIRECTION/ TYPE Input, Analog ACTIVE LEVEL N/A BALL B1 NAME ID DESCRIPTION ID pin of the USB cable. For applications not using ID this pin can be connected to VDD33. For an A-Device ID is grounded. For a B-Device ID is floated. This pin connects to an external resistor (RVBUS) connected to the VBUS pin of the USB cable. This pin is used for the VBUS comparator inputs and for VBUS pulsing during session request protocol. Regulator input. The regulator supply can be from 5.5V to 3.1V. C2 VBUS I/O, Analog N/A C1 VBAT Power N/A SMSC USB332x 5 Revision 0.3 (02-04-08) PRODUCT PREVIEW Miniature Hi-Speed USB Transceiver with 1.8V ULPI Interface Table 1 USB332x Pin Description (continued) DIRECTION/ TYPE Power ACTIVE LEVEL N/A BALL D2 NAME VDD33 DESCRIPTION 3.3V Regulator Output. A 2.2uF (