EM-6027S

MODEL: EM6027S PRODUCT: Electret Condenser Microphone TYPE: OMNI DIRECTIONAL BACK ELECTRET CONDENSER MICROPHONE ELECTRICAL CHARACTERISTICS Temperature =20±2 °C Humidity=65±5% parameter symbol condition sensitivity S 0dB=1V/Pa at 1kHz output impedance Z out current consumption limits unit min center max -51 -48 -45 dB f=1kHz 2.2 KΩ IDSS VCC =2.0V, RL=2.2KΩ 500 µA signal to noise ratio S/N at 1kHz S.P.L=1Pa (A-Weighted Curve) decreasing voltage ΔS VCC=3.0V to2.0V operating voltage 58 1.0 maximum input S.P.L dB -3 dB 10 V 115 dB TYPICAL FREQUENCY RESPONSE CURVE FREQUENCY RESPONSE MICROPHONE RESPONSE TOLERANCE WINDOW Frequency(Hz) Lower Limit(dB) Upper Limit(dB) 50 -6 +3 100 -3 +3 800 -3 +3 1000 0 0 1200 -3 +3 3000 -3 +8 5000 -3 +8 12000 -8 +8 MEASUREMENT CIRCUIT RL = 2.2KΩ Vs = 2.0V C1 = 10PF C2 = 33PF C = 1µF PAGE 1/5 MODEL: EM6027S PRODUCT: Electret Condenser Microphone TEMPERATURE CONDITIONS storage temperature range -40C ~ +85C operation temperature range -40C ~ +85C Note: Store in electronic warehouse. TERMINAL MECHANICAL STRENGTH Terminal should be no interference in operation after pulled the terminal with 1kg for 1 minute. RELIABILITY TEST After each of following tests, the sensitivity of the microphone should be within ±3dB of initial sensitivity after 3 hours of conditioning at 20°C . vibration test frequency 10hz ~ 55hz amplitude 1.52mm change of frequency 1 octave/min 2 hours in each of axis high temperature test +85°C for 240 hours low temperature test -40°C for 240 hours humidity test 90% ~ 95%RH, +60°C for 240 hours thermal shocking test –40°C, 30 minutes temperature cycles -40°C (2h) +80°C, 30 minutes, repeated 32 cycles +20°C (0.5h) (2h) +85°C (0.1h) (2h) +20°C (0.5h) (2h) room temperature, 3 hours -40°C (0.5h) (2h) for 5 cycles packing drop test height 1.5m procedure 5 times from each of axis electrostatic discharge Tested to IEC61000-4-2 level 3 contact discharge The microphone shall operate normally after 10 discharges to is 6KV DC and the discharge network is 150pF & 330Ω. air discharge The microphone shall operate normally after 10 discharges to is 8KV DC and the discharge network is 150pF & 330Ω SOLDERING CONDITION We suggest using an anti-static welding machine which can control soldering temperature automatically. Soldering temperature should be controlled at under 320 °C and soldering time for each terminal should be 1~2 seconds. Microphone should be fixed on the metal block (heat sink), which has high radiation effects, and heat sink shall contact with MIC tightly. Microphone may easily be destroyed by the static electricity and the countermeasure for eliminating the static electricity shall be electrocution (worktable and human body shall be ground connection). PAGE 2/5 MODEL: EM6027S PRODUCT: Electret Condenser Microphone MEASUREMENT SETUP DRAWING PRODUCT EXTERNAL VIEW AND DIMENSION Unit : mm EXPLODED DRAWING AND MATERIAL TABLE Name Material Quantity 1 Dustproof gauze Non-weave cloth 1 2 Case Al-Mg alloy 1 3 Diaphragm 1 4 Spacer 1 5 Electret plate 1 6 Chamber 1 7 Copper ring 1 8 PCB 1 9 FET 1 10 PIN 2 11 Capacitor 1 Remark 10+33pF PAGE 3/5 MODEL: EM6027S PRODUCT: Electret Condenser Microphone HEAT SINK SHAPE OF HEAT SINK SHAPE OF HOLE AT FIXED PART PAGE 4/5 MODEL: EM6027S PRODUCT: Electret Condenser Microphone PACKING DIMENSION: (LENGTH*WIDTH *HEIGHT) Anti-Static Bag: 80mm*80mm*2mm SMALL PACKET: 80mm*80 mm*10mm MIDDLE BOX:175mm*85mm*50mm CARTON SIZE: 550mm*230mm*235mm QUANTITY AND WEIGHT 100PCS/Small Box 1000PCS/Mid Box 30000PCS/Per Carton 1PC=0.1g NET WEIGHT：3.0kg GROSS WEIGHT：7.0kg X1 100PCS X14 1400PCS X20 28000PCS PAGE 5/5