PB-2418-2

Specifications PB PIEZO AUDIO BUZZER Acoustic Product Specification Product Number: PB-2418-2 Item Unit Specification Rated Voltage VDC 12.0 Operating Voltage VDC 3.0 ~ 20.0 Mean Current mA 15 Max. At rated voltage Sound Output dB 95 At 10cm at rated voltage. Rated Frequency Hz 3300±500 Operating Temp ℃ -20 ~ +85 Storage Temp ℃ -30 ~ +85 Dimension mm Ø24.0xH17.5 Weight gram 5.4 Material PBT(Black) Terminal Pin type (Plating Sn) Environmental Protection Regulation RoHS Condition See attached drawing. See attached drawing. Release | Revision: C/2018 Test condition: Temperature: +25±2℃ Related Humidity: 65±5% Air Pressure: 86-106KPa CONTENTS This document contains the technical specifications for the Piezo Audio Buzzer. Page 1 Specifications Mechanical Characteristics Item Test Condition Evaluation Standard Solderability Lead terminals are immersed in rosin for 5 seconds and then immersed in the solder bath at +250±5℃ for 3±1 seconds. 90% min. lead terminals shall be wet with solder. (Except the edge of terminal) Soldering Heat Resistance Lead terminals are immersed in the soldering bath at +250±5℃ for 3±1 seconds. The force of 9.8N(1.0Kg) is applied to the part for 10 seconds. No interference in operation. Terminal Mechanical Strength The force of 9.8N is applied to each terminal in axial direction for 10 seconds. No damage and cutting off. Vibration The buzzer shall be measured after a vibration of amplitude of 1.5mm with 10Hz to 55Hz band of vibration frequency is applied to each of 3 perpendicular directions for 2 hours After the test, the part shall meet specifications without any damage in appearance and performance except SPL. Drop Test The part is dropped from a height of 75cm onto a 40mm thick wooden board 3 times in 3 axes (X,Y,Z). A total of 9 times. Mechanical Characteristics Page 2 Environment Test Reliability Test Page 3 Inspection Fixture Frequency Response Recommended Wave Soldering Temperature Curve Page 4 Dimensions Page 5 Packing 1 www.soberton.com Environment Test Item Test Condition Evaluation Standard High Temp. Test PB PIEZO AUDIO BUZZER The part is placed in a chamber at +85℃ for 96 hours. Low Temp. Test The part is placed in a chamber at -30℃ for 96 hours. Acoustic Product Specification Humidity Test The part is placed in a chamber at +40℃, and 90±5% relative humidity for 96 hours. After the test, the part shall meet specifications without any degradation in appearance and performance except SPL. After 4 hours at +25℃ ±2˚C, the SPL should be in ±10dBA compared with initial one. Temp/Humidity Cycle The part shall be subjected to 5 cycles, Each cycle shall consist of: Product Number: PB-2418-2 Release | Revision: C/2018 CONTENTS This document contains the technical specifications for the Piezo Audio Buzzer. Page 1 Specifications Mechanical Characteristics Page 2 Environment Test Reliability Test Reliability Test Item Test Condition Evaluation Standard Operating Life Test 1. Continuous Life Test 48 hours of continuous operation at +55℃ with the maximum rated voltage applied After the test, the part shall meet specifications without any degradation in appearance and performance except SPL. After 4 hours at +25℃ ±2˚C, the SPL should be in ±10dBA compared with initial one. 2. Intermittent Life Test A duty cycle of 1 minute on, 1 minute off, a minimum of 1000 times at +25±2℃ and the maximum rated voltage applied Page 3 Inspection Fixture Frequency Response Recommended Wave Soldering Temperature Curve Page 4 Dimensions Standard Test Condition: a) Temperature: +5~+35℃ b) Humidity: 45~85% c) Pressure: 86~106KPa Page 5 Packing 2 www.soberton.com Inspection Fixture S.P.L Measuring Circuit Input Signal: 12 VDC MIC: S.P.L meter TES1351B or equivalent PB PIEZO AUDIO BUZZER Acoustic Product Specification Product Number: PB-2418-2 Frequency Response Release | Revision: C/2018 CONTENTS This document contains the technical specifications for the Piezo Audio Buzzer. Page 1 Specifications Mechanical Characteristics Recommended Wave Soldering Temperature Curve Page 2 Environment Test Reliability Test Page 3 Inspection Fixture Frequency Response Recommended Wave Soldering Temperature Curve Page 4 Dimensions Page 5 Packing 3 www.soberton.com Dimensions Tolerance: ±0.5 (unit: mm) PB PIEZO AUDIO BUZZER Acoustic Product Specification Sound Emission Hole 1 Product Number: PB-2418-2 2 3 4 5 6 Release | Revision: C/2018 CONTENTS This document contains the technical specifications for the Piezo Audio Buzzer. No. Part Name Material Quantity 1 Case PBT 1 2 PIN Copper 2 3 PCB Epoxy 1 4 Wire Copper Wire 3 Page 2 Environment Test 5 Piezo Brass + Ceramic 1 Reliability Test 6 Case PBT 1 Page 1 Specifications Mechanical Characteristics Page 3 Inspection Fixture Frequency Response Recommended Wave Soldering Temperature Curve Page 4 Dimensions Page 5 Packing 4 www.soberton.com Packing PB PIEZO AUDIO BUZZER Acoustic Product Specification Product Number: PB-2418-2 Details Release | Revision: C/2018 CONTENTS This document contains the technical specifications for the Piezo Audio Buzzer. Per Bag: 50 pcs Per Carton: 40 bags Per Carton: 2,000pcs Volume: 660 x 360 x 260mm Page 1 Specifications Mechanical Characteristics Page 2 Environment Test Reliability Test Page 3 Inspection Fixture Frequency Response Recommended Wave Soldering Temperature Curve Page 4 Dimensions Page 5 Packing 5 www.soberton.com