Specifications
PB PIEZO AUDIO
BUZZER
Acoustic Product Specification
Product Number: PB-4216-2
Item
Unit
Specification
Rated Voltage
VDC
12.0
Operating Voltage
VDC
3.0 ~ 20.0
Mean Current
mA
10.0 Max.
At rated voltage
Sound Output
dB
90
At 30cm at rated voltage.
Rated Frequency
Hz
2800±500
Operating Temp
℃
-20 ~ +55
Storage Temp
℃
-30 ~ +70
Dimension
mm
Ø41.6xH16.0
Weight
gram
9.0
Material
ABS(Black)
Terminal
Wire Type
Environmental
Protection Regulation
RoHS
Condition
See attached drawing.
Wire 140mm
(UL1007/AWG26#)
Release | Revision: B/2018
Test condition:
Temperature: +25±2℃ Related Humidity: 65±5% Air Pressure: 86-106KPa
CONTENTS
This document contains the
technical specifications for the
Piezo Audio Buzzer.
Page 1
Specifications
Mechanical Characteristics
Item
Test Condition
Evaluation Standard
Solderability
Lead terminals are immersed in
rosin for 5 seconds and then
immersed in the solder bath at
+250±5℃ for 3±1 seconds.
90% min. lead
terminals shall be wet
with solder.
(Except the edge of
terminal)
Soldering Heat
Resistance
Lead terminals are immersed in
the soldering bath at +250±5℃
for 3±1seconds. The force of
9.8N(1.0Kg) is applied to the part
for 10 seconds.
No interference in
operation.
Terminal Mechanical
Strength
The pull force shall be applied to
double lead wires:
Horizontal 3.0N(0.306kg) for 30
seconds.
Vertical 2.0N(0.204kg) for 30
seconds.
No damage and
cutting off.
Vibration
The buzzer shall be measured
after a vibration of amplitude of
1.5mm with 10Hz to 55Hz band
of vibration frequency is applied
to each of 3 perpendicular
directions for 2 hours
Drop Test
The part is dropped from a height
of 75cm onto a 40mm thick
wooden board 3 times in 3 axes
(X,Y,Z). A total of 9 times.
The value of
oscillation frequency
current consumption
should be in±10%
compared with initial
ones.
The SPL should be
in±10dB compared
with initial one.
Mechanical Characteristics
Page 2
Environment Test
Reliability Test
Page 3
Inspection Fixture
Frequency Response
Page 4
Dimensions
Page 5
Packing
www.soberton.com
1
Environment Test
Item
Test Condition
Evaluation Standard
High Temp. Test
PB PIEZO AUDIO
BUZZER
The part is placed in a chamber
at +70℃ for 96 hours.
Low Temp. Test
The part is placed in a chamber
at -30℃ for 96 hours.
Acoustic Product Specification
Humidity Test
The part is placed in a chamber
at +70℃, and 90±5% relative
humidity for 96 hours.
After the test, the part
shall meet specifications
without any
degradation in
appearance and
performance except
SPL. After 4 hours at
+25℃ ±2˚C, the SPL
should be in ±10dBA
compared with initial
one.
Temp/Humidity
Cycle
The part shall be subjected to 5 cycles,
Each cycle shall consist of:
Product Number: PB-4216-2
Release | Revision: B/2018
CONTENTS
This document contains the
technical specifications for the
Piezo Audio Buzzer.
Page 1
Specifications
Mechanical Characteristics
Page 2
Environment Test
Reliability Test
Reliability Test
Item
Test Condition
Evaluation Standard
Operating Life Test
1. Continuous Life Test
48 hours of continuous
operation at +55℃ with the
maximum rated voltage applied.
After the test, the part
shall meet specifications
without any
degradation in
appearance and
performance except
SPL.
After 4 hours at +25℃
±2˚C, the SPL should be
in ±10dBA compared
with initial one.
2. Intermittent Life Test
A duty cycle of 1 minute on,
1 minute off, a minimum of
1000 times at +25±2℃ and the
maximum rated voltage applied.
Page 3
Inspection Fixture
Frequency Response
Page 4
Dimensions
Page 5
Packing
Standard Test Condition:
a) Temperature: +5~+35℃
b) Humidity: 45~85%
c) Pressure: 86~106KPa
2
www.soberton.com
Inspection Fixture
S.P.L Measuring Circuit
Input Signal: 12 VDC
MIC: S.P.L meter TES1351B or equivalent
PB PIEZO AUDIO
BUZZER
Acoustic Product Specification
Product Number: PB-4216-2
Frequency Response
Release | Revision: B/2018
CONTENTS
This document contains the
technical specifications for the
Piezo Audio Buzzer.
Page 1
Specifications
Mechanical Characteristics
Page 2
Environment Test
Reliability Test
Page 3
Inspection Fixture
Frequency Response
Page 4
Dimensions
Page 5
Packing
3
www.soberton.com
Dimensions
Tolerance: ±0.5 (unit: mm)
PB PIEZO AUDIO
BUZZER
Acoustic Product Specification
Product Number: PB-4216-2
Emission
Release | Revision: B/2018
CONTENTS
This document contains the
technical specifications for the
Piezo Audio Buzzer.
Page 1
Specifications
Mechanical Characteristics
Page 2
Environment Test
Reliability Test
Page 3
Inspection Fixture
Frequency Response
Page 4
Dimensions
Page 5
Packing
No.
Part Name
Material
Quantity
1
Case
ABS
1
2
Cover
ABS
1
3
Piezo
Brass + Ceramic
1
4
Wire (140mm)
UL1007 AWG26#
(300V/ 1.3mm)
2
5
Wire
Copper
3
6
PCB
Epoxy
1
4
www.soberton.com
Packing
PB PIEZO AUDIO
BUZZER
Acoustic Product Specification
Product Number: PB-4216-2
Release | Revision: B/2018
CONTENTS
This document contains the
technical specifications for the
Piezo Audio Buzzer.
Packing Box
L x W x H (mm)
Quantity (pcs)
Per Box
300 x 200 x 50
72
Per Carton (12 Boxes)
430 x 320 x 280
864
Page 1
Specifications
Mechanical Characteristics
Page 2
Environment Test
Reliability Test
Page 3
Inspection Fixture
Frequency Response
Page 4
Dimensions
Page 5
Packing
5
www.soberton.com
很抱歉,暂时无法提供与“PB-4216-2”相匹配的价格&库存,您可以联系我们找货
免费人工找货