PT-1706

Specifications PT PIEZO AUDIO TRANSDUCER Acoustic Product Specification Product Number: PT-1706 Release | Revision: B/2018 CONTENTS This document contains the technical specifications for the Piezo Audio Transducer. Page 1 Specifications Item Unit Specification Rated Voltage Vp-p 5.0 Operating Voltage Vp-p 1.0 ~ 18.0 Mean Current mA 3 Max. Capacitance at 30Hz pF 10000±30% Sound Output dB 80 Rated Frequency Hz 4000±500 Operating Temp ℃ -30 ~ +70 Storage Temp ℃ -40 ~ +85 Dimension mm Ø16.5×H6.7 Weight gram 3.0 Material LCP(Black) Terminal Pin type (Plating Sn) Environmental Protection Regulation RoHS Condition At rated voltage At 10cm at rated voltage. See attached drawing. See attached drawing. Test condition: Temperature: +25±2℃ Related Humidity: 65±5% Air Pressure: 86-106KPa Mechanical Characteristics Item Test Condition Evaluation Standard Solderability Lead terminals are immersed in rosin for 5 seconds and then immersed in the solder bath at +250±5℃ for 3±1 seconds. 90% min. lead terminals shall be wet with solder. (Except the edge of terminal) Soldering Heat Resistance Lead terminals are immersed in the soldering bath at +250±5℃ for 3±1 seconds. No interference in operation. Frequency Response Terminal Mechanical Strength The force of 9.8N is applied to each terminal in axial direction for 10 seconds. No damage and cutting off. Recommended Wave Soldering Temperature Curve Vibration The buzzer shall be measured after a vibration of amplitude of 1.5mm with 10Hz to 55Hz band of vibration frequency is applied to each of 3 perpendicular directions for 2 hours. Drop Test The part is dropped from a height of 75cm onto a 40mm thick wooden board 3 times in 3 axes (X,Y,Z). A total of 9 times. The value of oscillation frequency current consumption should be in ±10% compared with initial ones. The SPL should be in ±10dB compared with initial one. Mechanical Characteristics Page 2 Environment Test Reliability Test Page 3 Inspection Fixture Page 4 Dimensions Page 5 Packing 1 www.soberton.com Environment Test Item Test Condition Evaluation Standard High Temp. Test PT PIEZO AUDIO TRANSDUCER The part is placed in a chamber at +85℃ for 96 hours. Low Temp. Test The part is placed in a chamber at -40℃ for 96 hours. Acoustic Product Specification Humidity Test The part is placed in a chamber at +40℃, and 90±5% relative humidity for 96 hours. After the test, the part shall meet specifications without any degradation in appearance and performance except SPL. After 4 hours at +25℃ ±2˚C, the SPL should be in ±10dBA compared with initial one. Temp/Humidity Cycle The part shall be subjected to 5 cycles, Each cycle shall consist of: Product Number: PT-1706 Release | Revision: B/2018 CONTENTS This document contains the technical specifications for the Piezo Audio Transducer. Page 1 Specifications Mechanical Characteristics Page 2 Environment Test Reliability Test Reliability Test Item Test Condition Evaluation Standard Operating Life Test 1. Continuous Life Test 48 hours of continuous operation at +70℃ with the maximum rated voltage applied. After the test, the part shall meet specifications without any degradation in appearance and performance except SPL. After 4 hours at +25℃ ±2˚C, the SPL should be in ±10dBA compared with initial one. 2. Intermittent Life Test A duty cycle of 1 minute on, 1 minute off, a minimum of 1000 times at +25±2℃ and the maximum rated voltage applied. Page 3 Inspection Fixture Frequency Response Recommended Wave Soldering Temperature Curve Page 4 Dimensions Page 5 Packing Standard Test Condition: a) Temperature: +5~+35℃ b) Humidity: 45~85% c) Pressure: 86~106KPa 2 www.soberton.com Inspection Fixture S.P.L Measuring Circuit PT PIEZO AUDIO TRANSDUCER Input Signal: 5.0 Vp-p , square wave, 4000Hz MIC: S.P.L meter TES1351B or equivalent S.G: Hewlett Packard 33120A Function Generator or equivalent Acoustic Product Specification Product Number: PT-1706 Frequency Response Release | Revision: B/2018 CONTENTS This document contains the technical specifications for the Piezo Audio Transducer. Page 1 Specifications Mechanical Characteristics Recommended Wave Soldering Temperature Curve Page 2 Environment Test Reliability Test Page 3 Inspection Fixture Frequency Response Recommended Wave Soldering Temperature Curve Page 4 Dimensions Page 5 Packing 3 www.soberton.com Dimensions Tolerance: ±0.5 (unit: mm) PT PIEZO AUDIO TRANSDUCER Emission Acoustic Product Specification Product Number: PT-1706 Release | Revision: B/2018 CONTENTS This document contains the technical specifications for the Piezo Audio Transducer. Page 1 Specifications No. Part Name Material Quantity Mechanical Characteristics 1 Case LCP 1 Page 2 Environment Test 2 Cover LCP 1 3 Piezo Copper + Ceramics 1 4 Pin Copper 2 Reliability Test Page 3 Inspection Fixture Frequency Response Recommended Wave Soldering Temperature Curve Page 4 Dimensions Page 5 Packing 4 www.soberton.com Packing PT PIEZO AUDIO TRANSDUCER Acoustic Product Specification Product Number: PT-1706 Release | Revision: B/2018 CONTENTS This document contains the technical specifications for the Piezo Audio Transducer. Page 1 Specifications Mechanical Characteristics Page 2 Environment Test Reliability Test Page 3 Inspection Fixture Frequency Response Recommended Wave Soldering Temperature Curve Page 4 Dimensions Page 5 Packing 5 www.soberton.com