Dynamic Speaker Electroacoustic Characteristics
Sound Pressure Level
86dB(1W/0.5m) ±3dB at AVE 0.8KHz, 1.0KHz, 1.2KHz, 1.5KHz
Measuring conditions and procedures shown in Fig 1 & Fig 2
SP DYNAMIC
SPEAKER UNIT
Frequency Response Curve
As shown in Figure 3
Resonance Frequency (F0)
Acoustic Product Specification
650 ±20%Hz
Input Power (Nominal and Maximum)
Product Number: SP-2040
SP-1605-3
Rated Noise Power: 1.0W
Short Term Max Power: 2.0W
Frequency Range
F0 ~ 6KHz.
Buzz, Rattle, Etc
Not audible from 650Hz to 20KHz with 2.83V Sine Wave Input
Polarity
Release | Revision: B/2017
When positive voltage is applied to the terminal marked (+), diaphragm
should be moved to the front.
Magnet
Rare earth permanent (NdFeB) magnet φ11x2mm
CONTENTS
This document contains the
technical specifications for the
dynamic speaker unit.
Page 1
Speaker Electroacoustic
Characteristics
General Specifications
Page 2
Reliability Tests
Page 3
Measuring Method (Speaker
Mode)
Block Diagram for Measurement
Method
Page 4
Frequency Response Curve
AC Impedance
8Ω ±15%
Distortion
Input Rated Power to 1.0W
Dimension
20x40x8.4mm
General Specifications
Operating Temperature Range
-30℃~+80℃
Storage Temperature Range
-40˚C ~ +85˚C
Standard Test Conditions
Temperature 5℃~35℃
Page 5
Dimensions
Page 6
Packing
Relative Humidity 45%~80%(RH)
Air Pressure 860 mbar ~ 1060 mbar
IP Level
No rating
www.soberton.com
1
Reliability Tests
The sound pressure as specified will neither deviate more than ±3dB from the initial
value, nor have any significant damage after any of following testing.
High Temperature Test
SP DYNAMIC
SPEAKER UNIT
Acoustic Product Specification
High Temperature +85±3℃
Duration 96 hours
Low Temperature Test
Low Temperature -40±3℃
Duration 96 hours
Product Number: SP-2040
SP-1605-3
Humidity Test
Temperature +40±3℃
Relative Humidity 92%~95%
Duration 96 hours
Vibration
10Hz ~ 55Hz ~ 10Hz sine wave sweep 15 minute 5G(constant)
X, Y, Z
3 directions, 2 hours each, total 6 hours
Release | Revision: B/2017
Temperature Cycle Test
The part will be subjected to 5 cycles. One cycle shall be 12 hours and
consist of:
CONTENTS
This document contains the
technical specifications for the
dynamic speaker unit.
Page 1
Speaker Electroacoustic
Characteristics
General Specifications
Page 2
Reliability Tests
Page 3
Measuring Method (Speaker
Mode)
Block Diagram for Measurement
Method
Page 4
Frequency Response Curve
Drop Test
Free drop from 100cm height to the concrete floor
X,Y, Z 6 directions 1 time each, total 6 times
Load Test
Rated Power White noise is applied for 96 hours at room temp.
Max Power Test
Max power 1 minute on - 2 minutes off, 10 cycles
Terminal Strength Test
Page 5
Dimensions
Capable of withstanding 1kg load for 30 seconds without resulting in any
damage or rejection
Page 6
Packing
2
www.soberton.com
Measuring Method (Speaker Mode) (Fig. 1)
SP DYNAMIC
SPEAKER UNIT
Acoustic Product Specification
Product Number: SP-2040
SP-1605-3
Block Diagram for Measurement Method (Fig. 2)
Release | Revision: B/2017
CONTENTS
This document contains the
technical specifications for the
dynamic speaker unit.
Page 1
Speaker Electroacoustic
Characteristics
General Specifications
Page 2
Reliability Tests
Page 3
Measuring Method (Speaker
Mode)
Block Diagram for Measurement
Method
Page 4
Frequency Response Curve
Page 5
Dimensions
Page 6
Packing
3
www.soberton.com
Frequency Response Curve (Fig. 3)
The swept sine-wave frequency response of a loudspeaker should ideally not
deviate more than indicated.
SP DYNAMIC
SPEAKER UNIT
Acoustic Product Specification
Product Number: SP-2040
SP-1605-3
Release | Revision: B/2017
CONTENTS
This document contains the
technical specifications for the
dynamic speaker unit.
Page 1
Speaker Electroacoustic
Characteristics
General Specifications
Page 2
Reliability Tests
Page 3
Measuring Method (Speaker
Mode)
Block Diagram for Measurement
Method
Page 4
Frequency Response Curve
Page 5
Dimensions
Page 6
Packing
4
www.soberton.com
Dimensions
Tolerance: ±0.5 (unit: mm)
SP DYNAMIC
SPEAKER UNIT
Acoustic Product Specification
Product Number: SP-2040
SP-1605-3
Release | Revision: B/2017
CONTENTS
This document contains the
technical specifications for the
dynamic speaker unit.
Page 1
Speaker Electroacoustic
Characteristics
No.
Part Name
Material
Quantity
1
Frame
ABS
1
2
PCB Terminal
Paper Cu
1
Page 3
Measuring Method (Speaker
Mode)
3
Magnet
NdFeB
1
4
Plate
SPCC
1
Block Diagram for Measurement
Method
5
Voice Coil
Paper Cu
1
6
Diaphragm
Cloth
1
7
CAP
Paper
1
General Specifications
Page 2
Reliability Tests
Page 4
Frequency Response Curve
Page 5
Dimensions
Page 6
Packing
5
www.soberton.com
Packing
SP DYNAMIC
SPEAKER UNIT
50pcs per tray
10 trays per units, 1 unit per carton
Total: 1000 pcs per box
Size:36.5 x 27 x 31.5cm
Acoustic Product Specification
Product Number: SP-2040
SP-1605-3
Release | Revision: B/2017
CONTENTS
This document contains the
technical specifications for the
dynamic speaker unit.
Page 1
Speaker Electroacoustic
Characteristics
General Specifications
Page 2
Reliability Tests
Page 3
Measuring Method (Speaker
Mode)
Block Diagram for Measurement
Method
Page 4
Frequency Response Curve
Page 5
Dimensions
Page 6
Packing
6
www.soberton.com
很抱歉,暂时无法提供与“SP-2040”相匹配的价格&库存,您可以联系我们找货
免费人工找货