ST-03BH

Specifications Item Unit Specification Condition Rated Voltage Vo-p 3.6 Vo-p Operating Voltage Vo-p 2.5 ~ 4.5 ST BUZZER Mean Current mA 100 Max. Acoustic Product Specification Coil Resistance Ω 16 ±3 Sound Output dB 88 Rated Frequency Hz 2730 Operating Temp ℃ -30 ~ +70 Storage Temp ℃ -40 ~ +85 Dimension mm L8.5 × W8.5 × H3.0 Weight gram 0.6 Product Number: ST-03BH Release | Revision: E/2018 CONTENTS This document contains the technical specifications for the electromagnetic buzzer. Page 1 Specifications Mechanical Characteristics Material LCP (Black) Terminal SMD type (Plating Sn) Environmental Protection Regulation RoHS Page 3 Frequency Response Curve Page 4 Recommended Temperature Profile Measurement Test Circuit See attached drawing Mechanical Characteristics Item Test condition Evaluation standard Solderability Lead terminals are immersed in the solder bath at +250±5℃ for 3±1 seconds. Soldering Heat Resistance The product follows the reflow temperature curve to test its reflow thermal stability. 90% min. lead terminals shall be wet with solder No interference in operation. Terminal Mechanical Strength Lead pads shall be soldered on the pc board, and the force of 9.8N (1.0Kg) shall be applied to the part for 10 seconds. No damage and cutting off Vibration The part shall be subjected to a vibration cycle of 10Hz to 55Hz to 10Hz in a period of 1 minute. Total peak amplitude shall be 1.52mm(9.3G). The vibration test shall consist of 2 hours per axis in each three axes (X,Y,Z). Total 6 hours. Drop Test The part is dropped from a height of 75cm onto a 40mm thick wooden board 3 times in 3 axes (X,Y,Z). Total of 9 times. After the test, the part shall meet specifications without any damage in appearance and performance except SPL. The SPL should be in ±10dBA compared with initial one. Page 5 Dimensions www.soberton.com See attached drawing Temperature : +25±2 ℃ Relative Humidity: 65±5% Air Pressure: 86-106KPa Inspection Fixture Page 6 Packing At 10cm(A-weight free air), at rated voltage 2730Hz, square wave, ½ duty Test Condition Page 2 Environment Test Reliability Test At rated voltage, 2730 Hz square wave, ½ duty Environment Test Item Test condition Evaluation standard High Temp. Test The part is placed in a chamber at +85℃ for 96 hours Low Temp. Test The part is placed in a chamber at -40℃ for 96 hours Thermal Shock The part shall be subjected to 10 cycles. Each cycle shall consist of: After the test, the part shall meet specifications without any degradation in appearance and performance except SPL. After 4 hours at +25℃, the SPL should be in ±10dBA compared with initial one. Temp./Humidity Cycle The part shall be subjected to 10 cycles. One cycle shall be 24 hours and consist of: ST BUZZER Acoustic Product Specification Product Number: ST-03BH Release | Revision: E/2018 CONTENTS This document contains the technical specifications for the electromagnetic buzzer. Page 1 Specifications Mechanical Characteristics Page 2 Environment Test Reliability Test Page 3 Frequency Response Curve Page 4 Recommended Temperature Profile Measurement Test Circuit Inspection Fixture Page 5 Dimensions Page 6 Packing www.soberton.com Reliability Test Item Test condition Evaluation standard Operating Life Test Ordinary Temperature The part shall be subjected to 96 hours of continuous operation at +25˚C±10˚C. After the test, the part shall meet specifications without any degradation in appearance and performance except SPL. After 4 hours at +25℃, the SPL should be in ±10dBA compared with initial one. High Temperature The part shall be subjected to 72 hours of continuous operation at +70℃ at 3.6V, 2730Hz applied. Low Temperature The part shall be subjected to 72 hours of continuous operation at -30℃ at 3.6V, 2730Hz applied. Standard test condition: a) Temperature: +5~+35℃ b) Humidity: 45~85% c) Pressure: 86~106KPa Typical Frequency Response Curve ST BUZZER Acoustic Product Specification Product Number: ST-03BH Release | Revision: E/2018 CONTENTS This document contains the technical specifications for the electromagnetic buzzer. Page 1 Specifications Mechanical Characteristics Page 2 Environment Test Reliability Test Page 3 Frequency Response Curve Page 4 Recommended Temperature Profile Measurement Test Circuit Inspection Fixture Page 5 Dimensions Page 6 Packing www.soberton.com Recommended Temperature Profile for Reflow Oven ST BUZZER Recommendable wave soldering condition is as follows: Note 1: It is requested that reflow soldering should be executed after heat of product goes down to normal temperature. Note 2: Peak reflow temperature of 250˚C maximum of 10 seconds, with a maximum duration of 40-60 seconds between 220˚C and 250˚C Acoustic Product Specification Product Number: ST-03BH Measurement Test Circuit Release | Revision: E/2018 CONTENTS This document contains the technical specifications for the electromagnetic buzzer. Page 1 Specifications Mechanical Characteristics Page 2 Environment Test Inspection Fixture S.P.L Measuring Circuit Input Signal: 3.6 Vo-p, square wave ½ duty, 2730 Hz Reliability Test Page 3 Frequency Response Curve Page 4 Recommended Temperature Profile Measurement Test Circuit Inspection Fixture Page 5 Dimensions Page 6 Packing www.soberton.com Mic: RION S.P.L meter UC30 or equivalent S.G: Hewlett Packard 33120A Function Generator or equivalent Dimensions ST BUZZER Acoustic Product Specification Product Number: ST-03BH Release | Revision: E/2018 CONTENTS This document contains the technical specifications for the electromagnetic buzzer. Page 1 Specifications Mechanical Characteristics Page 2 Environment Test No. Part Name Material Quantity 1 Case LCP 1 2 Core Ferrum 1 Page 4 Recommended Temperature Profile 3 Coil Copper 1 4 Magnet ring NdFeB 1 Measurement Test Circuit 5 Diaphragm Ferrum 1 Inspection Fixture 6 Case LCP 1 Reliability Test Page 3 Frequency Response Curve Page 5 Dimensions Page 6 Packing www.soberton.com Packing ST BUZZER Acoustic Product Specification Product Number: ST-03BH Release | Revision: E/2018 CONTENTS This document contains the technical specifications for the electromagnetic buzzer. Page 1 Specifications Mechanical Characteristics Page 2 Environment Test Reliability Test Page 3 Frequency Response Curve Page 4 Recommended Temperature Profile Measurement Test Circuit Inspection Fixture Page 5 Dimensions Page 6 Packing www.soberton.com