0
登录后你可以
  • 下载海量资料
  • 学习在线课程
  • 观看技术视频
  • 写文章/发帖/加入社区
会员中心
创作中心
发布
  • 发文章

  • 发资料

  • 发帖

  • 提问

  • 发视频

创作活动
CXA1853AQ

CXA1853AQ

  • 厂商:

    SONY(索尼)

  • 封装:

  • 描述:

    CXA1853AQ - RGB Driver for LCD - Sony Corporation

  • 数据手册
  • 价格&库存
CXA1853AQ 数据手册
CXA1853AQ RGB Driver for LCD Description The CXA1853AQ is an RGB driver for LCD panels. It supports a line alternative RGB drive system. Features • Built-in RGB signal phase matching sample-andhold circuit • Effective frequency response (18MHz Typ.) • Built-in gain and breakpoint variable 2-point γ compensation circuit • Built-in side black generation circuit for 4:3/16:9 aspect conversion • Built-in VCOM voltage output circuit Structure Bipolar silicon monolithic IC Applications • Liquid crystal projectors • Liquid crystal viewfinders • Compact liquid crystal monitors 80 pin QFP (Plastic) Absolute Maximum Ratings (Ta = 25°C) • Supply voltage VCC1 6 VCC2 15 • Input pin voltage VIN VCC1 • Operating temperature Topr –25 to +75 • Storage temperature Tstg –55 to +150 • Allowable power dissipation PD 1500 Operating Conditions • Supply voltage V V V °C °C mW VCC1 VCC2 • RGB input signal voltage VIN 4.75 to 5.25 11.0 to 14.0 0.7 V V Vp-p Note) Note) Defined as the amplitude from the pedestal level to white. Sony reserves the right to change products and specifications without prior notice. This information does not convey any license by any implication or otherwise under any patents or other right. Application circuits shown, if any, are typical examples illustrating the operation of the devices. Sony cannot assume responsibility for any problems arising out of the use of these circuits. –1– E96334-PS CXA1853AQ Block Diagram GCA DETG GCA DETR GCA DETB RGB GAIN GAM SEL 42 SIG SEL R GAIN B GAIN XCLP1 GND IREF N.C. 60 GND 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 XCLP2 SH4 VCC4 N.C. SH2 SH3 41 SH1 61 PVCC 62 SH IN 63 GND 64 B CLAMP 65 S/H S/H GCA CLP S/H S/H S/H GCA GAIN CONT WHT LIM 40 BLK CENT BLKLMT CTRL 39 BLK LIM 38 VCOM OUT 37 SIG CENT CTR 36 VCOM CTR EA BUFF R CLAMP 67 S/H EA PRG G CLAMP 66 35 PRG 34 GND R GAM GAIN1 69 B GAM GAIN1 70 RGB GAM GAIN2 71 R GAM GAIN2 72 B GAM GAIN2 73 RGB GAM CTR2 74 R GAM CTR2 75 B GAM CTR2 76 RGB GAM CTR1 77 R GAM CTR1 78 B GAM CTR1 79 Rγ CONT RGB GAM GAIN1 68 SID 33 SID FRP 32 FRP S/H S/H GCA EA S/H BUFF RGB γ CONT 31 PRG CTR 30 SID CTR 29 SID CLP Bγ CONT γ AMP γ AMP γ AMP 28 R CLP SW BUFF BUFF 27 G CLP 26 B CLP SW BUFF 25 R SBRT SBRT CONT 24 B SBRT 23 RGB SBRT 22 GND SW BUFF CLP CLP N.C. 80 BRT CONT CLP 21 N.C. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 GND N.C. RGB MBRT GAM OUT SID OUT N.C. VCC1 VCC2 N.C. R OUT N.C. R MBRT G OUT B MBRT B OUT –2– VCC3 N.C. RIN GIN BIN CXA1853AQ Pin Description Pin NO. Symbol Pin voltage VCC1 2k 200 37k 80k 80k 40µA 40µA (VCC1 = 5V, VCC2 = 13V) Equivalent circuit Description 1 RGB MBRT 1.6 to 5.0V∗ 1 RGB signal common main brightness control. Preset internally to 3.3V. 40µA GND VCC1 4 R MBRT 1.6 to 5.0V∗ 200 4 5 5k 80k 74k 80k 40µA 20µA VCC1 100 R signal main brightness control. Preset internally to 3.3V. B signal main brightness control. Preset internally to 3.3V. 5 B MBRT 1.6 to 5.0V∗ GND 20µA 2V Reference level 7 GAM OUT 7 G signal output of which main bright and gamma are adjusted and insert the reference signal. 100 GND 8 9 VCC1 RIN 5V VCC1 50µA 9 200 5V power supply. R signal input. Input a 0.7Vp-p signal.Note 2) G signal input. Input a 0.7Vp-p signal.Note 2) B signal input. Input a 0.7Vp-p signal.Note 2) GND. VCC2 10 GIN 10 11 6.2k 11 12 BIN GND 0V GND 13 SID OUT 9.3Vp-p Typ. 10 13 10 SID signal output. GND Note 1) ∗ in the Pin voltage indicates external applied voltage. Note 2) Defined as the amplitude from the pedestal level to white. –3– CXA1853AQ Pin NO. 14 15 VCC2 Symbol Pin voltage 13V VCC2 Equivalent circuit Description 13V power supply. R signal output. 15 16 R OUT 16 G OUT 4.5V Typ. 10 10 G signal output. 17 17 18 22 B OUT VCC3 GND 5V 0V GND B signal output. 5V power supply. GND. VCC3 3k 200 200 27k 23 RGB SBRT 1.6 to 5.0V∗ 23 RGB signal common sub brightness control. 13µA 53µA GND 53µA 24 B SBRT 1.6 to 5.0V∗ VCC3 3k 200 24 25 118k 80k 40µA 26µA 80k B signal sub brightness control. Preset internally to 3.3V. 25 R SBRT 1.6 to 5.0V∗ 26µA GND R signal sub brightness control. Preset internally to 3.3V. 26 B CLP VCC2 26 200 2k B output detection signal input. G output detection signal input. 10µA 27 G CLP 4.7 to 8.3V∗ 27 28 28 R CLP GND R output detection signal input. Note) ∗ in the Pin voltage indicates external applied voltage. –4– CXA1853AQ Pin NO. Symbol Pin voltage VCC2 Equivalent circuit Description 200 2k 29 SID CLP 4.7 to 8.3V∗ 29 10µA GND VCC3 3k 200 80k 35k 80k 40µA 53µA SID output detection signal input. Use an average value detecting external capacitor with a small leak current absolute value and tolerance. 30 SID CTR 1.6 to 5.0V∗ 30 SID output amplitude control. Preset internally to 3.3V. 53µA GND VCC3 3k 90k 31 PRG CTR 1.6 to 5.0V∗ 200 31 Level control for the PRG signal inserted into the SID signal. 90k GND VCC3 10µA 32 FRP 5V 0V 32 200 FRP input. This pulse is used to invert the polarity of the RGB output. Output is inverted when Low, and noninverted when High. Input level: High ≥ 4V Low ≤ 1V GND VCC3 10µA 33 SID FRP 0V 5V 33 200 GND FRP pulse input for SID output. This pulse is used to invert the polarity of the SID output. Output is inverted when Low, and non-inverted when High. Input level: High ≥ 4V Low ≤ 1V GND. 34 GND 0V Note) ∗ in the Pin voltage indicates external applied voltage. –5– CXA1853AQ Pin NO. Symbol Pin voltage VCC3 5V Equivalent circuit Description 10µA 200 35 PRG 0V 35 PRG pulse input. This pulse is used to insert the PRG signal into the SID output. Input level: High ≥ 4V Low ≤ 1V GND VCC2 200 80k 50k 80k 40µA 17µA VCC2 200 80k 50k 80k 40µA 26µA 36 VCOM CTR 1.6 to 5.0V∗ 36 17µA GND VCOM voltage control. The VCOM voltage variable range is –0.8V to +1.3V with respect to the signal center voltage. 37 SIG CENT CTR 1.6 to 5.0V∗ 37 RGB and SID signal center voltage control. 26µA GND VCC2 38 VCOM OUT 3.4 to 9.1V∗ 10 38 10 VCOM voltage output. GND VCC2 2k 200 100k 127k 100k 40µA 20µA 39 BLK LIM 1.6 to 5.0V∗ 39 Limiter control for limiting the output amplitude of the RGB signal. Preset internally to 3.3V. 20µA GND Note) ∗ in the Pin voltage indicates external applied voltage. –6– CXA1853AQ Pin NO. Symbol Pin voltage VCC2 Equivalent circuit Description 2k 200 100k 50k 100k 40µA 20µA 40 BLK CENT 1.6 to 5.0V∗ 40 20µA GND RGB signal output limiter center control. Preset internally to 3.3V. When preset, the limiter center becomes equal to the RGB output center. VCC3 2k 200 100k 37k 100k 40µA 20µA VCC1 55k 41 WHT LIM 1.6 to 5.0V∗ 41 RGB signal white peak limiter control. Preset internally to 3.3V. 20µA GND 42 GAM SEL 5.0V∗ 200 42 Gamma circuit control. Gamma ON when High, gamma OFF when Low. Input level: High ≥ 4V Low ≤ 1V GND 5V VCC1 43 XCLP2 0V 2.0µs 43 5V 44 GND 1.2µs VCC4 55k 200 Reference signal pulse input. Reference level when Low. Input level: High ≥ 4V Low ≤ 1V Clamp pulse input. Clamped when Low. Input level: High ≥ 4V Low ≤ 1V 44 XCLP1 0V 1.5k 200 200 38k 45 RGB GAIN 1.6 to 5.0V∗ 45 Gain control for RGB signal common variable gain amplifier. 20µA 40µA GND 40µA Note) ∗ in the Pin voltage indicates external applied voltage. –7– CXA1853AQ Pin NO. Symbol Pin voltage VCC4 Equivalent circuit Description Gain control for R signal variable gain amplifier. Preset internally to 3.3V. Gain control for B signal variable gain amplifier. Preset internally to 3.3V. GND. 46 R GAIN 1.6 to 5.0V∗ 46 47 1k 200 48k 80k 80k 40µA 80µA 47 B GAIN 1.6 to 5.0V∗ GND 80µA 48 GND 0V VCC4 5k 5k 49 IREF 1.2V 49 2k 200 10k Sample-and -hold circuit current setting. GND 50 51 VCC4 GCADET B 5.0V VCC4 40µA 51 5V power supply. B GCA circuit clamp detection. G GCA circuit clamp detection. 6.2k 52 GCADET G 1.8V Typ. 52 53 53 GCADET R GND R GCA circuit clamp detection. VCC4 55k 54 SIG SEL 0 to 5.0V∗ 200 54 GND Selection of input signal to Sample-and -hold circuit. R and B signals selected when High, G signal selected when Low. Input level: High ≥ 4V Low ≤ 1V GND. 55 56 57 58 61 62 GND SH4 SH3 SH2 SH1 PVCC 0V PVCC 56 5V 0V 57 58 59 100 GND 200 100µA Sample-and-hold pulse input. Input level: High ≥ 3.0V Low ≤ 1.0V Sampling when High, hold when Low. 5V 5V power supply. Note) ∗ in the Pin voltage indicates external applied voltage. –8– CXA1853AQ Pin NO. Symbol Pin voltage 2.25V Reference level Equivalent circuit VCC4 100µA 200 63 Description 63 SH IN Sample-and-hold circuit input. 6.2k GND 64 65 GND B CLAMP 0V VCC1 40µA 65 66 67 GND. B signal clamp detection. 66 G CLAMP 2.1V Typ. G signal clamp detection. 67 R CLAMP GND R signal clamp detection. VCC1 1k 200 200 37k 68 RGB GAM GAIN 1 1.6 to 5.0V∗ 68 RGB signal common black side voltage gain control. 40µA 40µA GND VCC1 40µA 69 R GAM GAIN 1 1.6 to 5.0V∗ 200 69 70 1k 80k 37k 80k 40µA 40µA R signal black side voltage gain control. Preset internally to 3.3V. B signal black side voltage gain control. Preset internally to 3.3V. 70 B GAM GAIN 1 1.6 to 5.0V∗ GND 40µA VCC1 1k 200 200 37k 71 RGB GAM GAIN 2 1.6 to 5.0V∗ 71 RGB signal common white side voltage gain control. 40µA 40µA GND 40µA Note) ∗ in the Pin voltage indicates external applied voltage. –9– CXA1853AQ Pin NO. Symbol Pin voltage VCC1 Equivalent circuit Description R signal white side voltage gain control. Preset internally to 3.3V. B signal white side voltage gain control. Preset internally to 3.3V. 72 R GAM GAIN 2 1.6 to 5.0V∗ 200 72 73 1k 80k 37k 80k 40µA 40µA 73 B GAM GAIN 2 1.6 to 5.0V∗ GND 40µA VCC1 1k 200 200 37k 74 RGB GAM CTR 2 1.6 to 5.0V∗ 74 RGB signal common white side voltage gain change point control. 40µA 40µA GND VCC1 40µA 75 R GAM CTR 2 1.6 to 5.0V∗ 200 75 76 3k 80k 74k 80k 40µA 20µA R signal white side voltage gain change point control. Preset internally to 3.3V. B signal white side voltage gain change point control. Preset internally to 3.3V. 76 B GAM CTR 2 1.6 to 5.0V∗ GND VCC1 20µA 1k 200 200 37k 77 RGB GAM CTR 1 1.6 to 5.0V∗ 77 RGB signal common black side voltage gain change point control. 40µA 40µA GND VCC1 40µA 78 R GAM CTR 1 1.6 to 5.0V∗ 78 79 3k 200 74k 80k 80k 40µA 20µA R signal black side voltage gain change point control. Preset internally to 3.3V. B signal black side voltage gain change point control. Preset internally to 3.3V. 79 B GAM CTR 1 1.6 to 5.0V∗ GND 20µA Note) ∗ in the Pin voltage indicates external applied voltage. – 10 – CXA1853AQ Electrical Characteristics Unless otherwise specified: Ta = 25°C, VCC1 = VCC3 = VCC4 = PVCC = 5V, VCC2 = 13V SW1 = OFF, SW4 = OFF, SW5 = OFF, SW9 = a, SW10 = a, SW11 = a, SW24 = OFF, SW25 = OFF, SW26 = a, SW27 = a, SW28 = a, SW29 = a, SW30 = OFF, SW36 = OFF, SW37 = OFF, SW39 = OFF, SW40 = OFF, SW41 = OFF, SW46 = OFF, SW47 = OFF, SW51 = a, SW52 = a, SW53 = a, SW63 = a, SW65 = a, SW66 = a, SW67 = a, SW69 = OFF, SW70 = OFF, SW72 = OFF, SW73 = OFF, SW75 = OFF, SW76 = OFF, SW78 = OFF, SW79 = OFF, V23 = 3.1V, V31 = 3.5V, V42 = 5.0V, V45 = 2.8V, V54 = 5.0V, V68 = 1.6V, V71 = 1.6V, V74 = 1.6V, V77 = 5.0V Set (R IN), (G IN), (B IN) and (TEST IN) = 0V, (SH1), (SH2), (SH3) and (SH4) = 5V, and input SG4 to (FRP) and (SID FRP), SG5 to (PRG), SG2 to (XCLP2) and SG3 to (XCLP1). No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 Item Current consumption (1) Current consumption (2) Current consumption (3) Current consumption (4) Current consumption (5) R IN pin current “Z” R IN pin current “H” R IN pin current “L” G IN pin current “Z” G IN pin current “H” G IN pin current “L” B IN pin current “Z” B IN pin current “H” B IN pin current “L” RGB SBRT pin current B CLP pin current G CLP pin current R CLP pin current SID CLP pin current PRG CTR pin current FRP pin current “H” FRP pin current “L” SID FRP pin current “H” SID FRP pin current “L” PRG pin current “H” PRG pin current “L” GAM SEL pin current “H” Symbol ICC1 ICC2 ICC3 ICC4 ICC5 IZ9 IH9 IL9 IZ10 IH10 IL10 IZ11 IH11 IL11 I23 I26 I27 I28 I29 I31 IH32 IL32 IH33 IL33 IH35 IL35 IH42 Measurement conditions Measure the current entering Pin 8. Measure the current entering Pin 14. Measure the current entering Pin 18. Measure the current entering Pin 50. Measure the current entering Pin 62. SW9 → b, (XCLP1) = 5V, V9 = 2.4V SW9 → b, (XCLP1) = 0V, V9 = 3.4V SW9 → b, (XCLP1) = 0V, V9 = 1.4V SW10 → b, (XCLP1) = 5V, V10 = 2.4V SW10 → b, (XCLP1) = 0V, V10 = 3.4V SW10 → b, (XCLP1) = 0V, V10 = 1.4V SW11 → b, (XCLP1) = 5V, V11 = 2.4V SW11 → b, (XCLP1) = 0V, V11 = 3.4V SW11 → b, (XCLP1) = 0V, V11 = 1.4V V23 = 5.0V SW26 → b, V26 = 7.0V SW27 → b, V27 = 7.0V SW28 → b, V28 = 7.0V SW29 → b, V29 = 7.0V V31 = 5.0V (FRP) = 5V (FRP) = 0V (SID FRP) = 5V (SID FRP) = 0V (PRG) = 5V (PRG) = 0V V42 = 5V Min. — — — — — –1.5 13 — –1.5 13 — –1.5 13 — — –0.2 –0.2 –0.2 –0.2 — –0.1 –0.3 –0.1 –0.3 –0.1 –0.3 –0.1 Typ. 30 11 6 29 4 0 25 –25 0 25 –25 0 25 –25 2.5 0 0 0 0 0.3 0 –0.1 0 –0.1 0 –0.1 0 Max. 44 18 10 43 7 1.5 — –13 1.5 — –13 1.5 — –13 6 0.2 0.2 0.2 0.2 0.8 0.1 — 0.1 — 0.1 — 0.1 Unit mA mA mA mA mA µA µA µA µA µA µA µA µA µA µA µA µA µA µA µA µA µA µA µA µA µA µA – 11 – CXA1853AQ No. 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 Item GAM SEL pin current “L” XCLP2 pin current “H” XCLP2 pin current “L” XCLP1 pin current “H” XCLP1 pin current “L” RGB GAIN pin current Symbol IL42 IH43 IL43 IH44 IL44 I45 Measurement conditions V42 = 0V (XCLP2) = 5V (XCLP2) = 0V (XCLP1) = 5V (XCLP1) = 0V V45 = 5V SW51 → b, (XCLP1) = 5V, V51 = 2.0V SW51 → b, (XCLP1) = 0V, V51 = 3.0V SW51 → b, (XCLP1) = 0V, V51 = 1.0V SW52 → b, (XCLP1) = 5V, V52 = 2.0V SW52 → b, (XCLP1) = 5V, V52 = 3.0V SW52 → b, (XCLP1) = 5V, V52 = 1.0V SW53 → b, (XCLP1) = 5V, V53 = 2.0V SW53 → b, (XCLP1) = 5V, V53 = 3.0V SW53 → b, (XCLP1) = 5V, V53 = 1.0V V54 = 5V V54 = 0V (SH4) = 5V (SH4) = 0V (SH3) = 5V (SH3) = 0V (SH2) = 5V (SH2) = 0V (SH1) = 5V (SH1) = 0V SW63 → b, (XCLP1) = 5V, V63 = 2.2V SW63 → b, (XCLP1) = 0V, V63 = 3.2V SW63 → b, (XCLP1) = 0V, V63 = 1.2V SW65 → b, (XCLP1) = 5V, V65 = 2.0V SW65 → b, (XCLP1) = 0V, V65 = 3.0V SW65 → b, (XCLP1) = 0V, V65 = 1.0V SW66 → b, (XCLP1) = 5V, V66 = 2.0V SW66 → b, (XCLP1) = 0V, V66 = 3.0V SW66 → b, (XCLP1) = 0V, V66 = 1.0V SW67 → b, (XCLP1) = 5V, V67 = 2.0V SW67 → b, (XCLP1) = 0V, V67 = 3.0V SW67 → b, (XCLP1) = 0V, V67 = 1.0V V68 = 5.0V Min. — –0.1 — –0.1 –1.0 — –0.5 15 — –0.5 15 — –0.5 15 — –0.1 –3.0 –0.1 –5.0 –0.1 –5.0 –0.1 –5.0 –0.1 –5.0 –1.5 13 — –0.5 15 — –0.5 15 — –0.5 15 — — Typ. –1.7 0 –1.0 0 –0.2 0.5 0 30 30 0 30 –30 0 30 –30 0 –1.0 0 –2.0 0 –2.0 0 –2.0 0 –2.0 0 25 –25 0 40 –40 0 40 –40 0 40 –40 0.5 Max. –0.4 0.1 –0.3 0.1 — 1.3 0.5 — –15 0.5 — –15 0.5 — –15 0.1 — 0.1 — 0.1 — 0.1 — 0.1 — 1.5 — –13 0.5 — –15 0.5 — –15 0.5 — –15 1.3 Unit µA µA µA µA µA µA µA µA µA µA µA µA µA µA µA µA µA µA µA µA µA µA µA µA µA µA µA µA µA µA µA µA µA µA µA µA µA µA GCA DET B pin current “Z” IZ51 GCA DET B pin current “H” IH51 GCA DET B pin current “L” IL51 GCA DET G pin current “Z” IZ52 GCA DET G pin current “H” IH52 GCA DET G pin current “L” IL52 GCA DET R pin current “Z” IZ53 GCA DET R pin current “H” IH53 GCA DET R pin current “L” IL53 SIG SEL pin current “H” SIG SEL pin current “L” SH4 pin current “H” SH4 pin current “L” SH3 pin current “H” SH3 pin current “L” SH2 pin current “H” SH2 pin current “L” SH1 pin current “H” SH1 pin current “L” SH IN pin current “Z” SH IN pin current “H” SH IN pin current “L” B CLAMP pin current “Z” B CLAMP pin current “H” B CLAMP pin current “L” G CLAMP pin current “Z” G CLAMP pin current “H” G CLAMP pin current “L” R CLAMP pin current “Z” R CLAMP pin current “H” R CLAMP pin current “L” I54H I54L I56H I56L I57H I57L I58H I58L I61H I61L IZ63 IH63 IL63 IZ65 IH65 IL65 IZ66 IH66 IL66 IZ67 IH67 IL67 RGB GAM GAIN1 pin current I68 – 12 – CXA1853AQ No. 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 Item Symbol Measurement conditions V71 = 5.0V V74 = 5.0V V77 = 5.0V Min. — — — 1.3 1.3 1.3 2.9 2.9 2.9 2.9 2.9 2.9 2.9 2.9 2.9 2.9 0.8 1.2 1.2 1.2 1.9 1.6 1.6 1.6 2.9 2.9 2.9 2.9 2.9 2.9 2.9 2.9 2.9 2.9 2.9 45 Typ. 0.5 0.5 0.5 1.7 1.7 1.7 3.3 3.3 3.3 3.3 3.3 3.3 3.3 3.3 3.3 3.3 1.2 1.8 1.8 1.8 2.3 2.1 2.1 2.1 3.3 3.3 3.3 3.3 3.3 3.3 3.3 3.3 3.3 3.3 3.3 80 Max. 1.3 1.3 1.3 2.1 2.1 2.1 3.7 3.7 3.7 3.7 3.7 3.7 3.7 3.7 3.7 3.7 1.6 2.4 2.4 2.4 2.7 2.6 2.6 2.6 3.7 3.7 3.7 3.7 3.7 3.7 3.7 3.7 3.7 3.7 3.7 110 Unit µA µA µA V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V kΩ RGB GAM GAIN2 pin current I71 RGB GAM CTR2 pin current RGB GAM CTR1 pin current RIN pin voltage GIN pin voltage BIN pin voltage B SBRT pin voltage R SBRT pin voltage SID CTR pin voltage VCOM CTR pin voltage I74 I77 V9 V10 V11 V24 V25 V30 V36 SIG CENT CTR pin voltage V37 BLK LIM pin voltage BLK CENT pin voltage WHT LIM pin voltage R GAIN pin voltage B GAIN pin voltage IREF pin voltage GCA DET B pin voltage GCA DET G pin voltage GCA DET R pin voltage SH IN pin voltage B CLAMP pin voltage G CLAMP pin voltage R CLAMP pin voltage V39 V40 V41 V46 V47 V49 V51 V52 V53 V63 V65 V66 V67 R GAM GAIN1 pin voltage V69 B GAM GAIN1 pin voltage V70 R GAM GAIN2 pin voltage V72 B GAM GAIN2 pin voltage V73 R GAM CTR2 pin voltage B GAM CTR2 pin voltage R GAM CTR1 pin voltage B GAM CTR1 pin voltage RGB MBRT pin voltage R MBRT pin voltage B MBRT pin voltage RGB MBRT input impedance V75 V76 V78 V79 V1 V4 V5 Z1 – 13 – CXA1853AQ No. 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 Item R MBRT input impedance B MBRT input impedance B SBRT input impedance R SBRT input impedance SID CTR input impedance VCOM CTR input impedance SIG CENT CTR input impedance BLK LIM input impedance BLK CENT input impedance WHT LIM input impedance R GAIN input impedance B GAIN input impedance R GAM GAIN1 input impedance B GAM GAIN1 input impedance R GAM GAIN2 input impedance B GAM GAIN2 input impedance R GAM CTR2 input impedance B GAM CTR2 input impedance R GAM CTR1 input impedance B GAM CTR1 input impedance Symbol Z4 Z5 Z24 Z25 Z30 Z36 Z37 Z39 Z40 Z41 Z46 Z47 Z69 Z70 Z72 Z73 Z75 Z76 Z78 Z79 Measurement conditions Min. 45 45 45 45 45 45 45 55 55 55 45 45 45 45 45 45 45 45 45 45 Typ. 80 80 80 80 80 80 80 100 100 100 80 80 80 80 80 80 80 80 80 80 Max. 110 110 110 110 110 110 110 150 150 150 110 110 110 110 110 110 110 110 110 110 Unit kΩ kΩ kΩ kΩ kΩ kΩ kΩ kΩ kΩ kΩ kΩ kΩ kΩ kΩ kΩ kΩ kΩ kΩ kΩ kΩ – 14 – CXA1853AQ No. Item Symbol Measurement conditions Set SW41 → ON, V41 = 1.6V, V42 = 0V, V54 = 0V and input SG1 (0 dB) to (TEST IN). Then adjust V45 so that the non-inverted output amplitude (black to white) at TP16 is 5 times the input signal amplitude and label this as VI. Input SG1 (–6 dB) to (TEST IN) and label the non-inverted output amplitudes (black to white) at TP15, TP16 and TP17 with V45 = VI as VRST, VGST and VBST, and the inverted output amplitudes as VRSTA, VGSTA and VBSTA, respectively. Next, label the non-inverted output amplitudes (black to white) at TP15, TP16 and TP17 with V45 = 5.0V as VRSM, VGSM and VBSM, and the inverted output amplitudes as VRSMA, VGSMA and VBSMA, respectively. Next, label the non-inverted output amplitudes (black to white) at TP15, TP16 and TP17 with V45 = 1.6V as VRSN, VGSN and VBSN, and the inverted output amplitudes as VRSNA, VGSNA and VBSNA, respectively. ∆GCS1 = 20log (VRSM (A)/VRST (A)) = 20log (VGSM (A)/VGST (A)) = 20log (VBSM (A)/VBST (A)) ∆GCS2 = 20log (VRSN (A)/VRST (A)) = 20log (VGSN (A)/VGST (A)) = 20log (VBSN (A)/VBST (A)) Set V42 = 0V, V54 = 0V, input SG1 (–6dB) to (TEST IN), and set V45 = VI, SW46 → ON, SW41 → ON, V41 = 1.6V and V46 = 5.0V. Then label the non-inverted output amplitude (black to white) at TP15 as VRSTM and the inverted output amplitude as VRSTMA. Next, label the non-inverted output amplitude (black to white) at TP15 with V46 = 1.6V as VRSTN and the inverted output amplitude as VRSTNA. ∆GRS1 = 20log (VRSTM (A)/VGST (A)) ∆GRS2 = 20log (VRSTN (A)/VGST (A)) Set V42 = 0V, V54 = 0V, input SG1 (–6dB) to (TEST IN), and set V45 = VI, SW47 → ON, SW41 → ON, V41 = 1.6V and V47 = 5.0V. Then label the non-inverted output amplitude (black to white) at TP17 as VBSTM and the inverted output amplitude as VBSTMA. Next, label the non-inverted output amplitude (black to white) at TP17 with V47 = 1.6V as VBSTN and the inverted output amplitude as VBSTNA. ∆GBS1 = 20log (VBSTM (A)/VGST (A)) ∆GBS2 = 20log (VBSTN (A)/VGST (A)) Min. Typ. Max. Unit 122 RGB GAIN adjustment range (1) ∆GCS1 4.0 6.0 — dB 123 RGB GAIN adjustment range (2) ∆GCS2 — –6.0 –4.0 dB 124 R GAIN adjustment range (1) ∆GRS1 2.5 4.6 — dB 125 R GAIN adjustment range (2) ∆GRS2 — –4.6 –2.5 dB 126 B GAIN adjustment range (1) ∆GBS1 2.5 4.6 — dB 127 B GAIN adjustment range (2) ∆GBS2 — –4.6 –2.5 dB – 15 – CXA1853AQ No. Item Symbol Measurement conditions Label the DC potentials at TP9, TP10 and TP11 as VRT, VGT and VBT, respectively. Next, label the DC potentials at TP9, TP10 and TP11 with SW1 → ON and V1 = 5.0V as VRN, VGN and VBN, respectively. Next, label the DC potentials at TP9, TP10 and TP11 with V1 = 1.6 V as VRM, VGM and VBM, respectively. ∆VBM1 = VRN – VRT, VGN – VGT, VBN – VBT ∆VBM2 = VRM – VRT, VGM – VGT, VBM – VBT Min. Typ. Max. Unit 128 RGB MBRT adjustment range (1) ∆VBM1 — –0.35 –0.30 V 129 RGB MBRT adjustment range (2) ∆VBM2 0.30 0.35 — V 130 R MBRT adjustment range (1) R MBRT adjustment range (2) B MBRT adjustment range (1) B MBRT adjustment range (2) ∆VBR1 131 ∆VBR2 Label the DC potential at TP9 with SW4 → ON — –0.16 –0.12 and V4 = 5.0V as VRTN. Next, label the DC potential at TP9 with V4 = 1.6V as VRTM. — 0.12 0.16 ∆VBR1 = VRTN – VGT ∆VBR2 = VRTM – VGT Label the DC potential at TP11 with SW5 → ON — –0.16 –0.12 and V5 = 5.0V as VBTN. Next, label the DC potential at TP11 with V5 = 1.6V as VBTM. — 0.12 0.16 ∆VBB1 = VBTN – VGT ∆VBB2 = VBTM – VGT Set SW39 → ON, V39 = 1.6V, V45 = 5.0V and V23 = 5.0V. Then measure the amplitudes (black to black) at TP15, TP16 and TP17. Set SW39 → ON and V39 = 1.6V. Then label the non-inverted reference level potentials at TP15, TP16 and TP17 as VSRT, VSGT and VSBT, and the inverted reference level potentials as VSRTA, VSGTA and VSBTA, respectively. Next, label the non-inverted reference level potentials at TP15, TP16 and TP17 with V23 = 1.6V as VSRN, VSGN and VSBN, and the inverted reference level potentials as VSRNA, VSGNA and VSBNA, respectively. Next, label the non-inverted reference level potentials at TP15, TP16 and TP17 with V23 = 5.0V as VSRM, VSGM and VSBM, and the inverted reference level potentials as VSRMA, VSGMA and VSBMA, respectively. VSBN = VSRNA – VSRN, VSGNA – VSGN, VSBNA – VSBN VSBM = VSRMA – VSRM, VSGMA – VSGM, VSBMA – VSBM V V 132 ∆VBB1 V 133 ∆VBB2 V 134 Maximum RGB output amplitude ∆VBMAX 10.0 10.7 — Vp-p 135 RGB SBRT adjustment range (1) VSBN — –0.7 0 V 136 RGB SBRT adjustment range (2) VSBM 8.5 10.7 — V – 16 – CXA1853AQ No. Item Symbol Measurement conditions Set SW39 → ON, V39 = 1.6V, SW25 → ON and V25 = 1.6V. Then label the non-inverted reference level potential at TP15 as VSRTN and the inverted reference level potential as VSRTNA. Next, label the non-inverted reference level potential at TP15 with V25 = 5.0V as VSRTM and the inverted reference level potential as VSRTMA. ∆VSSR1 = (VSRTNA – VSRTN) – (VSGTA – VSGT) ∆VSSR2 = (VSRTMA – VSRTM) – (VSGTA – VSGT) Set SW39 → ON, V39 = 1.6V, SW24 → ON and V24 = 1.6V. Then label the non-inverted reference level potential at TP17 as VSBTN and the inverted reference level potential as VSBTNA. Next, label the non-inverted reference level potential at TP17 with V24 = 5.0V as VSBTM and the inverted reference level potential as VSBTMA. ∆VSSB1 = (VSBTNA – VSBTN) – (VSGTA – VSGT) ∆VSSB2 = (VSBTMA – VSBTM) – (VSGTA – VSGT) ∆VS = VSRT (A) – VSGT (A), VSGT (A) – VSBT (A), VSBT (A) – VSRT (A) Min. Typ. Max. Unit 137 R SBRT adjustment range (1) ∆VSSR1 — –1.8 –1.2 V 138 R SBRT adjustment range (2) ∆VSSR2 1.2 1.8 — V 139 B SBRT adjustment range (1) ∆VSSB1 — –1.8 –1.2 V 140 B SBRT adjustment range (2) ∆VSSB2 1.2 1.8 — V 141 Reference level difference ∆VS between R, G and B –200 0 200 mV 142 Gain difference between R, G and B ∆GRGB Set V45 = VI, SW41 → ON, V41 = 1.6V and input SG1 (0dB) to (R IN), (G IN) and (B IN). Then label the non-inverted output amplitudes (black to white) at TP15, TP16 and TP17 as VRVT, VGVT and VBVT, and the inverted output amplitudes as –0.8 VRVTA, VGVTA and VBVTA, respectively. ∆GRGB = 20log (VBVT/VRVT), 20log (VRVT/VGVT), 20log (VGVT/VBVT) ∆GINV = 20log (VRVT/VRVTA), 20log (VGVT/VGVTA), 20log (VBVT/VBVTA) –0.7 0 0.8 dB 143 Difference between the inverted and non-inverted gain ∆GINV 0 0.7 dB 144 Difference between the ∆V50I reference level and 50 IRE Set V45 = VI. Then label the non-inverted output signal reference level amplitudes at TP15, TP16 and TP17 as VSR, VSG and VSB, and the inverted output signal reference level –150 amplitudes as VSRA, VSGA and VSBA, respectively. V50I = VSR (A) – VRVT (A)/2 = VSG (A) – VGVT (A)/2 = VSB (A) – VBVT (A)/2 (See “Black Side Gamma Measurement Method”.) Set V45 = VI. Then measure the minimum gain GN of the non8.0 inverted and inverted signals at TP15, TP16 and TP17. GGN = 20 log (GN) (See “Black Side Gamma Measurement Method”.) Set V45 = VI, V23 = 1.6V and V77 = 1.6V. –1.5 Then obtain the gamma gain of the non-inverted and inverted signals at TP15, TP16 and TP17. 0 150 mV 145 Gamma intermediate region gain GGN 9.8 12.0 dB 146 Minimum RGB gamma black side gain GCBN 0 1.5 dB – 17 – CXA1853AQ No. Item Symbol Measurement conditions (See “Black Side Gamma Measurement Method”.) Set V45 = VI, V23 = 1.6V, V68 = 5.0V and V77 = 1.6V. Then obtain the gamma gain of the non-inverted and inverted signals at TP15, TP16 and TP17. Min. Typ. Max. Unit 147 Maximum RGB gamma black side gain ∆GGBM 15 18 — dB 148 Gamma black side gain difference between R, G and B ∆GGBT (See “Black Side Gamma Measurement Method”.) Set V45 = VI, V23 = 1.6V, V68 = 3.0V and V77 = 1.6V. Then label the non-inverted side gamma gain at TP15, TP16 and TP17 as GBRT, GBGT and GBBT, –1.0 and the inverted side gamma gain as GBRTA, GBGTA and GBBTA, respectively. ∆GGBT = GBRT (A) – GBGT (A) = GBGT (A) – GBBT (A) = GBBT (A) – GBRT (A) (See “Black Side Gamma Measurement Method”.) Set V45 = VI, V23 = 1.6V, V68 = 3.0V, V77 = 1.6V, SW69 → ON and V69 = 1.6V. — Then measure the gamma gain at TP15, and label the non-inverted side as GBRN and the inverted side as GBRNA ∆GGBR1 = GBRN (A) – GBGT (A) Next, measure the gamma gain at TP15 with V69 = 5.0V, and label the non-inverted side as 2.5 GBRM and the inverted side as GBRMA. ∆GGBR2 = GBRM (A) – GBGT (A) (See “Black Side Gamma Measurement Method”.) Set V45 = VI, V23 = 1.6V, V68 = 3.0V, V77 = 1.6V, SW70 → ON and V70 = 1.6V. — Then measure the gamma gain at TP17, and label the non-inverted side as GBBN and the inverted side as GBBNA. ∆GGBB1 = GBBN (A) – GBGT (A) Next, measure the gamma gain at TP17 with V70 = 5.0V, and label the non-inverted side as 2.5 GBBM and the inverted side as GBBMA. ∆GGBB2 = GBBM (A) – GBGT (A) (See “White Side Gamma Measurement Method”.) Set V45 = VI, V23 = 1.6V, SW41 → ON, V41 = 1.6V, V71 = 1.6V and V74 = 5.0V. –1.5 Then measure the gamma gain of the non-inverted and inverted sides at TP15, TP16 and TP17. (See “White Side Gamma Measurement Method”.) Set V45 = VI, V23 = 1.6V, SW41 → ON, V41 = 1.6V, V71 = 5.0V and V74 = 5.0V. Then measure the gamma gain of the non-inverted and inverted sides at TP15, TP16 and TP17. 0 1.0 dB 149 R gamma black side sub gain adjustment range (1) ∆GGBR1 –4.5 –2.5 dB 150 R gamma black side sub gain adjustment range (2) ∆GGBR2 4.5 — dB 151 B gamma black side sub gain adjustment range (1) ∆GGBB1 –4.5 –2.5 dB 152 B gamma black side sub gain adjustment range (2) ∆GGBB2 4.5 — dB 153 Minimum RGB gamma white side gain GGWN 0 1.5 dB 154 Maximum RGB gamma white side gain GGWN 15 18 — dB – 18 – CXA1853AQ No. Item Symbol Measurement conditions Min. Typ. Max. Unit 155 Gamma white side gain difference between R, G and B ∆GGWT (See “White Side Gamma Measurement Method”.) Set V45 = VI, V23 = 1.6V, V71 = 3.0V, V74 = 5.0V, SW41 → ON and V41 = 1.6V. Then label the non-inverted side gamma gain at TP15, TP16 and TP17 as GWRT, GWGT and GWBT, and the inverted side gamma gain as –1.0 GWRTA, GWGTA and GWBTA, respectively. ∆GGWT = GWRT (A) – GWGT (A) = GWGT (A) – GWBT (A) = GWBT (A) – GWRT (A) (See “White Side Gamma Measurement Method”.) Set V45 = VI, V23 = 1.6V, V71 = 3.0V, V74 = 5.0V, SW41 → ON, V41 = 1.6V, SW72 → ON and V72 = 1.6V. Then measure the gamma gain at TP15, and label the non-inverted side as GWRN and the inverted side as GWRNA. ∆GGWR1 = GWRN (A) – GWGT (A) Next, measure the gamma gain at TP15 with V72 = 5.0V, and label the non-inverted side as GWRM and the inverted side as GWRMA. ∆GGWR2 = GWRM (A) – GWGT (A) (See “White Side Gamma Measurement Method”.) Set V45 = VI, V23 = 1.6V, V71 = 3.0V, V74 = 5.0V, SW41 → ON, V41 = 1.6V, SW73 → ON and V73 = 1.6V. Then measure the gamma gain at TP17, and label the non-inverted side as GWBN and the inverted side as GWBNA. ∆GGWB1 = GWBN (A) – GWGT (A) Next, measure the gamma gain at TP17 with V73 = 5.0V, and label the non-inverted side as GWBM and the inverted side as GWBMA. ∆GGWB2 = GWBM (A) – GWGT (A) 0 1.0 dB 156 R gamma white side sub gain adjustment range (1) ∆GGWR1 — –4.5 –2.5 dB 157 R gamma white side sub gain adjustment range (2) ∆GGWR2 2.5 4.5 — dB 158 B gamma white side sub gain adjustment range (1) ∆GGWB1 — –4.5 –2.5 dB 159 B gamma white side sub gain adjustment range (2) ∆GGWB2 2.5 4.5 — dB 160 Minimum RGB gamma PGBN black side breakpoint value (See “Black Side Gamma Measurement Method”.) Set V45 = VI, V23 = 1.6V, V68 = 5.0V and V77 = 1.6V. –0.45 –0.15 Then measure the gamma breakpoints of the non-inverted and inverted sides at TP15, TP16 and TP17. (See “Black Side Gamma Measurement Method”.) Set V45 = VI, V23 = 1.6V, V68 = 5.0V, V77 = 5.0V, SW1 → ON and V1 = 4.0V. Then measure the gamma breakpoints of the non-inverted and inverted sides at TP15, TP16 and TP17. — V 161 Maximum RGB gamma PGBM black side breakpoint value — –1.05 –0.75 V – 19 – CXA1853AQ No. Item Symbol Measurement conditions Min. Typ. Max. Unit 162 Gamma black side breakpoint difference between R, G and B ∆PGBT (See “Black Side Gamma Measurement Method”.) Set V45 = VI, V23 = 1.6V, V68 = 5.0V and V77 = 3.3V. Then measure the gamma breakpoints at TP15, TP16 and TP17 and label the non-inverted side as PGBRT, PGBGT and PGBBT, and the inverted –0.15 side as PGBRTA, PGBGTA and PGBBTA, respectively. ∆PGBT = PGBRT (A) – PGBGT (A) = PGBGT (A) – PGBBT (A) = PGBBT (A) – PGBRT (A) (See “Black Side Gamma Measurement Method”.) Set V45 = VI, V23 = 1.6V, V68 = 5.0V, V77 = 3.3V, SW78 → ON and V78 = 1.6V. Then measure the gamma breakpoint at TP15, and label the non-inverted side as PGBRN and the inverted side as PGBRNA. ∆PGBR1 = PGBRN (A) – PGBGT (A) Next, measure the gamma breakpoint at TP15 with V78 = 5.0V, SW1 → ON and V1 = 4.0V, and label the non-inverted side as PGBRM and the inverted side as PGBMA. ∆PGBR2 = PGBRM (A) – PGBGT (A) 0 0.15 V 163 R gamma black side breakpoint sub adjustment ∆PGBR1 range (1) 0.15 0.3 — V 164 R gamma black side breakpoint sub adjustment ∆PGBR2 range (2) — –0.3 –0.15 V 165 B gamma black side breakpoint sub adjustment ∆PGBB1 range (1) 166 B gamma black side breakpoint sub adjustment ∆PGBB2 range (2) (See “Black Side Gamma Measurement Method”.) Set V45 = VI, V23 = 1.6V, V68 = 5.0V, V77 = 3.3V, SW79 → ON and V79 = 1.6V. 0.15 Then measure the gamma breakpoint at TP17, and label the non-inverted side as PGBBN and the inverted side as PGBBNA. ∆PGBB1 = PGBBN (A) – PGBGT (A) Next, measure the gamma breakpoint at TP17 with V79 = 5.0V, SW1 → ON and V1 = 4.0V, and label — the non-inverted side as PGBBM and the inverted side as PGBBMA. ∆PGBB2 = PGBBM (A) – PGBGT (A) (See “White Side Gamma Measurement Method”.) Set V45 = VI, V23 = 1.6V, V71 = 5.0V, V74 = 5.0V, SW41 → ON and V41 = 1.6V. Then measure the gamma breakpoints of the noninverted and inverted sides at TP15, TP16 and TP17. (See “White Side Gamma Measurement Method”.) Set V45 = VI, V23 = 1.6V, V71 = 5.0V, V74 = 1.6V, SW1 → ON, V1 = 2.3V, SW41 → ON and V41 = 1.6V. Then measure the gamma breakpoints of the noninverted and inverted sides at TP15, TP16 and TP17. 0.3 — V –0.3 –0.15 V 167 Minimum RGB gamma PGWN white side breakpoint value — –0.35 –0.05 V 168 Maximum RGB gamma PGWM white side breakpoint value 0.75 1.20 — V 169 Gamma white side breakpoint difference between R, G and B ∆PGWT (See “White Side Gamma Measurement Method”.) Set V45 = VI, V23 = 1.6V, V71 = 5.0V, V74 = 3.3V, SW41 → ON and V41 = 1.6V. Then measure the gamma breakpoints at TP15, TP16 and TP17 and label the non-inverted sides as –0.15 PGWRT, PGWGT and PGWBT, and the inverted sides as PGWRTA, PGWGTA and PGWBTA, respectively. ∆PGWT = PGWRT (A) – PGWGT (A) = PGWGT (A) – PGWBT (A) = PGWBT (A) – PGWRT (A) 0 0.15 V – 20 – CXA1853AQ No. Item Symbol Measurement conditions Min. Typ. Max. Unit 170 R gamma white side breakpoint sub adjustment ∆PGWR1 range (1) 171 R gamma white side breakpoint sub adjustment ∆PGWR2 range (2) (See “White Side Gamma Measurement Method”.) Set V45 = VI, V23 = 1.6V, V71 = 5.0V, V74 = 3.3V, SW41 → ON and V41 = 1.6V. Then measure the gamma breakpoint at TP16, — and label the non-inverted side as PGWGT and the inverted side as PGWGTA. Next, measure the gamma breakpoint at TP15 with SW75 → ON and V75 = 5.0, and label the noninverted side as PGWRN and the inverted side as PGWRNA. ∆PGWR1 = PGWRN (A) – PGWGT (A) Next, measure the gamma breakpoint at TP15 with 0.15 V75 = 1.6V, SW1 → ON and V1 = 2.3V, and label the non-inverted side as PGWRM and the inverted side as PGWRMA. ∆PGWR2 = PGWRM (A) – PGWGT (A) (See “White Side Gamma Measurement Method”.) Set V45 = VI, V23 = 1.6V, V71 = 5.0V, V74 = 3.3V, SW41 → ON, V41 = 1.6V, SW76 → ON and — V76 = 5.0V. Then measure the gamma breakpoint at TP17, and label the non-inverted side as PGWBN and the inverted side as PGWBNA. ∆PGWB1 = PGWBN (A) – PGWGT (A) Next, measure the gamma breakpoint at TP17 with V75 = 1.6V, SW1 → ON and V1 = 2.3V, and set 0.15 the non-inverted side as PGWBM and the inverted side as PGWBMA. ∆PGWB2 = PGWBM (A) – PGWGT (A) Set V45 = 5.0V, V42 = 0V, V54 = 0V and input SG1 (0dB) to (TEST IN). Label the non-inverted output amplitudes (black to white) at TP15, TP16 and TP17 as VWRLT, VWGLT and VWBLT, and the inverted output amplitudes as VWRLTA, VWGLTA and VWBLTA, respectively. Next, label the non-inverted output amplitudes (black to white) at TP15, TP16 and TP17 with SW41 → ON and V41 = 5.0V as VWRLN, VWGLN and VWBLN, and the inverted output amplitudes as VWRLNA, VWGLNA and VWBLNA, respectively. Next, label the non-inverted output amplitudes (black to white) at TP15, TP16 and TP17 with V41 = 1.6V as VWRLM, VWGLM and VWBLM, and the inverted output amplitudes as VWRLMA, VWGLMA and VWBLMA, respectively. VWT = VWRLT (A), VWGLT (A), VWBLT (A) ∆VW1 = VWRLN (A) – VWRLT (A) = VWGLN (A) – VWGLT (A) = VWBLN (A) – VWBLT (A) ∆VW2 = VWRLM (A) – VWRLT (A) = VWGLM (A) – VWGLT (A) VWBLM (A) – VWBLT (A) –0.3 –0.15 V 0.3 — V 172 B gamma white side breakpoint sub adjustment ∆PGWB1 range (1) –0.3 –0.15 V 173 B gamma white side breakpoint sub adjustment ∆PGWB2 range (2) 0.3 — V 174 WHT LIM standard voltage VWT value 1.7 2.0 2.3 V 175 WHT LIM adjustment range (1) ∆VW1 — –1.7 –1.3 V 176 WHT LIM adjustment range (2) ∆VW2 2.4 2.8 — V – 21 – CXA1853AQ No. Item Symbol Measurement conditions Min. Typ. Max. Unit 177 BLK LIM standard voltage value (non-inverted side) VBLT 178 BLK LIM standard voltage value (inverted side) VBLTA 179 BLK LIM adjustment range ∆VBL1 (1) (non-inverted side) 180 BLK LIM adjustment range ∆VBL2 (2) (non-inverted side) 181 BLK LIM adjustment range ∆VBL3 (3) (inverted side) 182 BLK LIM adjustment range ∆VBL4 (4) (inverted side) Set V23 = 1.6V and V37 = 2.8V. Then label the DC voltages at TP15, TP16 and TP17 as VCR1, VCG1 and VCB1, respectively. Next, set V23 = 5.0V, SW26 → (b), SW27 → (b), 4.2 SW28 → (b), V26 = 7.0V, V27 = 7.0V and V28 = 7.0V, and then label the non-inverted limiter levels at TP15, TP16 and TP17 as VBRLT, VBGLT and VBBLT, and the inverted limiter levels as VBRLTA, VBGLTA and VBBLTA, respectively. Next, label the non-inverted limiter levels at TP15, TP16 and TP17 with SW39 → ON and V39 = 1.6V as VBRLM, VBGLM and VBBLM, and the 4.2 inverted limiter levels as VBRLMA, VBGLMA and VBBLMA, respectively. Next, label the non-inverted limiter levels at TP15, TP16 and TP17 with V39 = 5.0V as VBRLN, VBGLN and VBBLN, and the inverted limiter levels as VBRLNA, VBGLNA and VBBLNA, respectively. VBLT = VCR1 – VBRLT = VCG1 – VBGLT 0.7 = VCB1 – VBBLT VBLTA = VBRLTA – VCR1 = VBGLTA – VCG1 = VBBLTA – VCB1 ∆VBL1 = (VCR1 – VBRLM) – (VCR1 – VBRLT) = (VCG1 – VBGLM) – (VCG1 – VBGLT) — = (VCB1 – VBBLM) – (VCB1 – VBBLT) ∆VBL2 = (VCR1 – VBRLN) – (VCR1 – VBRLT) = (VCG1 – VBGLN) – (VCG1 – VBGLT) = (VCB1 – VBBLN) – (VCB1 – VBBLT) –0.5 ∆VBL3 = (VBRLMA – VCR1) – (VBRLTA – VCR1) = (VBGLMA – VCG1) – (VBGLTA – VCG1) = (VBBLMA – VCB1) – (VBBLTA – VCB1) ∆VBL4 = (VBRLNA – VCR1) – (VBRLTA – VCR1) — = (VBGLNA – VCG1) – (VBGLTA – VCG1) = (VBBLNA – VCB1) – (VBBLTA – VCB1) Set V42 = 0V and V23 = 2.1V. Then label the DC voltages at TP15, TP16 and 6.35 TP17 as VCRT, VCGT and VCBT, respectively. VCRGB = VCRT, VCGT, VCBT Set V31 = 1.6V, SW30 → ON and V30 = 1.6V. Then measure the DC voltage at TP13. 6.35 4.8 5.4 V 4.8 5.4 V 1.2 — V –2.7 –2.2 V 0 0.5 V –2.7 –2.2 V 183 RGB output DC voltage VCRGB 6.50 6.65 V 184 SID output DC voltage VCSID 6.50 6.65 V – 22 – CXA1853AQ No. Item Symbol Measurement conditions Min. Typ. Max. Unit 185 DC voltage difference between RGB and SID outputs ∆VCSRGB Set V42 = 0V, V31 = 1.6V, SW30 → ON, V30 = 1.6V and V37 = 2.8V. Then measure the DC voltages at TP13, TP15, TP16 and TP17, and level these voltages as VCS2, VCR2, VCG2 and VCB2, respectively. –150 ∆VCSRGB = VCS2 – VCR2, VCS2 – VCG2, VCS2 – VCB2 = VCR2 – VCG2, VCR2 – VCB2, VCG2 – VCB2 Set V42 = 0V, V37 = 5.0V, SW37 → ON. Then measure the DC voltages at TP13, TP15, TP16 and TP17. Set V42 = 0V, V37 = 1.6V, SW37 → ON. Then measure the DC voltages at TP15, TP16 and TP17. ∆VCOM = VCRT – VCOM = VCGT – VCOM = VCBT – VCOM — 0 150 mV 186 Minimum SIG CENT adjustment voltage Maximum SIG CENT adjustment voltage DC voltage difference between VCOM OUT and RGB output VC1 4.7 5.3 V 187 VC2 7.7 8.3 — V 188 ∆VCOM 100 300 500 mV 189 VCOM control range (1) ∆VCOM1 Set SW36 → ON and V36 = 5.0V. Then label the voltage at TP38 as VCOM1. ∆VCOM1 = VCRT – VCOM1 = VCGT – VCOM1 = VCBT – VCOM1 Set SW36 → ON and V36 = 1.6V. Then label the voltage at TP38 as VCOM2. ∆VCOM2 = VCRT – VCOM2 = VCGT – VCOM2 = VCBT – VCOM2 Set V31 = 1.6V. Then measure the output amplitude at TP13. Set V31 = 1.6V, SW30 → ON, V30 = 5.0V and VCC2 = 13V. Then measure the output amplitude at TP13. Set V31 = 1.6V, SW30 → ON, V30 = 1.6V and VCC2 = 13V. Then measure the output amplitude at TP13. Set V31 = 5.0V. Then measure the amplitude of the PRG section using the output waveform at TP13. –1.9 –1.6 V 190 VCOM control range (2) ∆VCOM2 2.1 2.4 V 191 SID OUT amplitude VSID 8.3 9.3 10.3 Vp-p 192 Maximum SID CTR control VSMAX voltage Minimum SID CTR control VSMIN voltage 10 11 — Vp-p 193 — 5.0 6.5 Vp-p 194 Maximum PRG CTR control voltage VPRGM VPRG 2.0 3.2 — Vp-p SG5 – 23 – CXA1853AQ No. 195 Item Minimum PRG CTR control voltage Symbol VPRGN Measurement conditions Set V31 = 1.6V. Then measure the amplitude of the PRG section using the output waveform at TP13. Frequency response from (R IN), (G IN) and (B IN) to TP15, TP16 and TP17 (frequency which goes to –3dB with respect to 100kHz) Frequency response from (R IN), (G IN) and (B IN) to the sample-and-hold circuit input (frequency which goes to –3dB with respect to 100kHz) Input SG6 to (R IN), (G IN) and (B IN). Then adjust V45 so that the output amplitude (black to white) at TP16 is 3V. Measure the slew rate from the 10 to 90% rise and fall time of TP15, TP16 and TP17. Set SW41 → ON, V41 = 1.6V and input SG1 (variable amplitude) to (R IN), (G IN) and (B IN). Then label the amplitude of the 1st, 5th and 10th steps as b1, b5 and b10, respectively, using the non-inverted output waveform at TP15, TP16 and TP17. The input dynamic range is defined as the minimum value for the input amplitude (black to white) at which b1/b5 < 0.8 or b10/b5 < 0.8. Set V45 = VI and input SG7 to (SH1), (SH2) and (SH3). Then measure the droop rate at TP15, TP16 and TP17. Next, input SG7 to (SH4). Then measure the droop rate of TP15, TP16 and TP17. Min. — Typ. 0 Max. 0.4 Unit Vp-p 196 Frequency response (1) fRGB (RGB input – RGB output) — 18 — MHz 197 Frequency response (3) (RGB input – γ) fγ 20 25 — MHz 198 Slew rate RSRGB (RGB input – RGB output) 60 100 — V/µs 199 Input dynamic range VDIN 0.8 1.1 — Vp-p 200 Sample-and-hold circuit droop rate RDLP — — 40 mV/µs 201 GAM OUT reference voltage amplitude GAM OUT GAIN (Maximum GAM gain) VGS Measure the reference signal voltage amplitude 0.15 of TP7. Input SG1 to (G IN). Then measure the output amplitude (black to white) of TP7, and label it as VG. –5.2 0.22 0.29 Vp-p 202 GG –4.2 –3.2 dB Note) The symbol (A) in the Measurement conditions inscription indicates that the measurement values for both the inverted and non-inverted sides are used. (Example) 20 log (VRSM (A)/VRST (A)) means both 20 log (VRSM/VRST) and 20 log (VRSMA/VRSTA). In this example, VRSM and VRST are non-inverted side measurement values and VRSMA and VRSTA are inverted side measurement values. – 24 – CXA1853AQ Black Side Gamma Measurement Method Measure the output voltages y1 to y10 which correspond to the input voltages a1 to a10 using SG8 as the input signal. (Measure the voltage from the reference level. Label the white side from the reference level as positive, and the black side as negative.) Select the two points where | yn – yn – 1 | (n = 2 to 10) is a maximum, and label these points yk and yk – 1. Also, label the input voltages which correspond to yk and yk – 1 as ak and ak – 1, respectively. Next, measure the output voltages y1 to y10 which correspond to the input voltages a1 to a10 using SG9 as the input signal. Select the two points where | yn – yn – 1 | (n = 2 to 10) is a maximum, and label these points yh and yh – 1. Also, label the input voltages which correspond to yh and yh – 1 as ah and ah – 1, respectively. From the above: Maximum gain GM = (yk – yk – 1)/(ak – ak – 1) Minimum gain GN = (yh – yh – 1)/(ah – ah – 1) The black side gamma gain is defined as the ratio of the maximum gain to the minimum gain. In other words: Gamma gain = 20 log (GM/GN) The gamma breakpoint is defined as the intersection between the straight line passing through points (ak, yk) and (ak – 1, yk – 1) and the straight line passing through points (ah, yh) and (ah – 1, yh – 1). In other words: Gamma breakpoint = (GM ∗ GN ∗ (ak – ah) – GN ∗ yk + GM ∗ yh)/(GM – GN) Reference level y10 y9 y8 y7 y6 y5 y4 Reference level y2 y3 y4 y5 y6 y7 y8 y9 y10 y1 y1 y2 y3 RGB output waveform (SG8) RGB output waveform (SG9) – 25 – CXA1853AQ White Side Gamma Measurement Method Measure the output voltages y1 to y10 which correspond to the input voltages a1 to a10 using SG9 as the input signal. (Measure the voltage from the reference level. Label the white side from the reference level as positive, and the black side as negative.) Select the two points where | yn – yn – 1 | (n = 2 to 10) is a maximum, and label these points yk and yk – 1. Also, label the input voltages which correspond to yk and yk – 1 as ak and ak – 1, respectively. Next, measure the output voltages y1 to y10 which correspond to the input voltages a1 to a10 using SG8 as the input signal. Select the two points where | yn – yn – 1 | (n = 2 to 10) is a maximum, and label these points yh and yh – 1. Also, label the input voltages which correspond to yh and yh – 1 as ah and ah – 1, respectively. From the above: Maximum gain GM = (yk – yk – 1)/(ak – ak – 1) Minimum gain GN = (yh – yh – 1)/(ah – ah – 1) The white side gamma gain is defined as the ratio of the maximum gain to the minimum gain. In other words: Gamma gain = 20 log (GM/GN) The gamma breakpoint is defined as the intersection between the straight line passing through points (ak, yk) and (ak – 1, yk – 1) and the straight line passing through points (ah, yh) and (ah – 1, yh – 1). In other words: Gamma breakpoint = (GM ∗ GN ∗ (ak – ah) – GN ∗ yk + GM ∗ yh)/(GM – GN) Reference level y1 y2 y3 y4 y5 y6 y7 y8 y9 y10 Reference level y4 y5 y6 y7 y8 y9 y10 y1 y2 y3 RGB output waveform (SG8) RGB output waveform (SG9) – 26 – CXA1853AQ Input Waveforms 10-step linear waveform 0dB Amplitude of the 10th step White 0.714V SG1 5µs Black Amplitude of the 5th step 0.286V Amplitude of the 1st step 64µs 2µs 5V SG2 0V 0.4µs 1.2µs 5V SG3 0V 5V SG4 0V 5V SG5 0V 6µs 1µs SG6 tr, tf < 5ns 0.714V 10µs 5V SG7 0V – 27 – CXA1853AQ SG8 35mV 35mV 35mV 35mV 35mV 35mV 35mV 35mV 35mV 35mV 35mV 35mV 35mV 35mV 35mV 35mV 35mV 35mV 35mV 35mV SG9 350mV – 28 – CXA1853AQ Electrical Characteristics Measurement Circuit (B IN) 0.1µ 390k 390k 390k 390k TP15 TP13 TP16 100 TP17 VCC2 (R IN) (a) (a) (b) SW11 (G IN) TP11 100 (a) (b) (b) SW9 TP9 VCC1 100µ 100µ 100µ 0.1µ 0.1µ VCC3 TP7 V5 SW5 V4 SW4 5 4 3 2 1 80 79 78 77 V77 76 75 74 V74 73 72 71 V71 70 69 68 V68 67 66 65 64 63 62 61 VCC5 0.1µ SW66 SW67 V66 0.1µ SW65 (b) SW70 SW69 V70 V69 (b) V67 (a) (b) (a) 0.1µ V65 0.1µ SW73 SW72 V73 V72 SW76 SW75 V76 V75 SW79 SW78 V79 V78 V1 SW1 1µ 1µ 1µ 1µ 0.1µ V29 V28 V27 V26 20 19 21 18 17 16 15 14 13 12 TP10 SW10 100 100 11 10 9 8 7 6 (b) (a) (a) (b) (b) (a) (b) 22 23 V23 V24 V25 SW24 SW25 24 25 26 27 28 29 V30 SW30 V31 (FRP) (SID FRP) 30 31 32 33 34 (PRG) V36 V37 SW36 SW37 TP38 SW39 40 V40 SW40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 37 38 39 V39 35 36 (a) SW28 SW27 SW29 SW26 (a) SW52 100µ V54 (b) SW63 (a) 0.1µ SH IN SW41 V42 V45 SW46 SW47 TP49 (b) (a) 100µ 0.1µ (XCLP2) (SH4) (SH3) (SH2) V46 V47 0.1µ (a) SW51 V51 (b) 0.1µ (a) V53 (b) SW53 – 29 – 0.1µ V52 VCC4 (SH1) V41 (XCLP1) 33k V63 CXA1853AQ Description of Operation Reference signal The reference level is inserted into the RGB signal by inputting the XCLP2 signal shown below during the RGB input signal pedestal level interval. Gamma compensation and clamping operation are performed based on this level. Reference signal RGB signal input XCLP1 1.2µ 0.4µ 0.4µ XCLP2 Bright adjustment The position of the RGB signal relative to the reference level changes according to the voltage applied to RGB MBRT (Pin 1). Bright can be controlled without changing the γ characteristics to the panel because the input bias is changed with the breakpoint for output kept constant. RGB signal output 50 IRE Low Bright pin voltage preset High – 30 – CXA1853AQ Gamma compensation The gamma compensation curve establishes the gain change points (breakpoints) on both the black and white sides from the reference level. The black and white side gains and the black and white side gain change points can each be adjusted independently. Output Output Reference level Reference level Input Input Gain adjustment Breakpoint variation Sample-and-hold, gain control and pedestal clamp Since sample-and-hold circuits are established in the R, G and B lines and each of these circuits is operated by an independent pulse, the delay can be set freely. In addition, the pulse leak is canceled by establishing a sample-and-hold circuit in the clamp loop and inputting the differential input of the gain control circuit. S/H S/H Gain control amplifier 45 To the inversion circuit S/H Clamp pulse Error amplifier Clamp voltage 57, 58, 61 56 51 to 53 Clamp capacitance S/H pulse – 31 – CXA1853AQ RGB inversion amplifier The polarity of the RGB output is inverted according to the FRP pulse. The relationship between input and output is as shown in the figure below. RGB IN FRP Signal center RGB OUT SID output The CXA1853Q outputs a side black signal for 4:3/16:9 aspect conversion. The black level is adjusted by the SID CTR pin. In addition, the PRG level can be set in part of the side black signal by inputting the PRG pulse. The PRG level is adjusted by the PRG CTR pin. The relationship between each input and output is as shown in the figure below. PRG SIDFRP Signal center SID OUT PRG level Signal center control The RGB and SID output center voltages are adjusted by the SIG CENT CTR (Pin 37). When SIG CENT CTR is preset, the output pin center voltage goes to VCC2/2. Output clamp The average value of each RGB and SID output signal is detected with external RC circuits and input to the RGB CLP and SID CLP pins. Then the center voltage offsets among R, G, B and SID outputs are reduced by feedback which equalizes these detected values and the signal center voltage set by the SIG CENT CTR pin. – 32 – CXA1853AQ Notes on Operation 1) R IN (Pin 9), G IN (Pin 10), B IN (Pin 11) input signal impedance An external capacitor is used as the hold capacitor for the clamp at the input of this IC. Therefore, the input signal impedance must be sufficiently low (75Ω or less) and the external capacitor must have a small leak current. 2) Clamp hold capacitors (Pins 51 to 53 and 65 to 67) The external capacitors connected to these pins must have a small leak current. 3) R, G, B, SID OUT load capacitance The output signal will tend to oscillate if the R, G, B and SID OUT load capacitance increases. Be sure to insert a 100 to 220Ω resistor in series to these output pins, and design to keep the load capacitance from exceeding 30pF. 4) External capacitor at the output The leak current absolute value and tolerance for the R, G, B and SID OUT average value detecting capacitors should be small. Note that if there is an offset in the leak current between R, G and B, offset voltage is also generated between R, G and B in the external resistor, which causes a DC offset of the output signal. R, G, B, SID OUT 100 to 220Ω Load capacitance 30pF or less 390kΩ R, G, B, SID CLP 1µF 5) GND and power supply pins Pins 12, 22, 34, 48, 55 and 64 (GND) should be set to the minimum identical potential applied to the IC, and should not be left open. In addition, the potential at Pins 8, 18, 50 and 62 should be the same. – 33 – CXA1853AQ Application Circuit CXD2412AQ Timing Generator 5V 0.01µ VR 100 100 100 100 VR VR 100 100 VR 100µ 0.1µ 0.1µ 0.1µ GCA DETG GCA DETR GCA DETB 33k RGB GAIN CAM SEL 42 WHT LIM 41 SIG SEL R GAIN B GAIN XCLP1 44 60 5V SH1 PVCC 0.01µ 100µ SH IN GND 0.1µ 0.1µ 0.1µ B CLAMP G CLAMP R CLAMP VR VR VR VR VR VR VR VR VR VR VR VR RGB GAM GAIN1 R GAM GAIN1 B GAM GAIN1 RGB GAM GAIN2 R GAM GAIN2 B GAM GAIN2 RGB GAM CTR2 R GAM CTR2 B GAM CTR2 RGB GAM CTR1 R GAM CTR1 B GAM CTR1 N.C. 61 62 63 64 65 66 67 68 69 70 GND 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 XCLP2 43 VCC4 IREF N.C. N.C. SH2 SH3 SH4 GND 40 39 38 37 36 35 34 33 32 31 CXA1853AQ 30 29 28 27 26 25 24 23 22 21 BLK CENT BLK LIM VCOM OUT SIG CENT CTR VCOM CTR PRG GND SID FRP FRP PRG CTR SID CTR SID CLP R CLP G CLP B CLP R SBRT B SBRT RGB SBRT GND N.C. VR VR VR VR VR VR VR VR 71 72 73 74 75 76 77 78 79 80 1 RGB MBRT N.C. 2 3 N.C. 4 R MBRT 5 B MBRT 6 N.C. GAM OUT 7 8 VCC1 9 RIN 10 GIN 11 BIN 12 GND 13 SID OUT 14 VCC2 15 R OUT 16 G OUT 17 B OUT 18 VCC3 19 N.C. 20 N.C. 5V 0.01µ 100µ 5V VR VR VR 0.01µ 33k indicated as VR. VR 0.1µ 0.1µ 0.1µ 68k R G B 150 buff 150 buff 150 buff 150 buff 390k 390k 390k 390k ANALOG RGB IN 13V 5V 13V 1µ 1µ 1µ 1µ 3.3k 0.01µ buff indicated as buff. 3.3k LCX007 LCD Panel 100µ 0.01µ 100µ Application circuits shown are typical examples illustrating the operation of the devices. Sony cannot assume responsibility for any problems arising out of the use of these circuits or for any infringement of third party patent and other right due to same. – 34 – CXA1853AQ Example of Representative Characteristics RGB GAIN adjustment range 8 6 4 8 6 4 R GAIN, B GAIN adjustment range ∆GCS [dB] 0 –2 –4 –6 –8 2 3 4 RGB GAIN (V45) [V] 5 ∆GRS [dB] 2 2 0 –2 –4 –6 –8 2 3 4 R GAIN (V46) [V] B GAIN (V47) [V] 5 RGB MBRT adjustment range 0.4 0.2 R MBRT, B MBRT adjustment range 0.2 0.1 ∆VBM [V] 0 ∆VBR [V] 2 3 4 RGB MBRT (V1) [V] 5 0 –0.2 –0.1 –0.4 –0.2 2 3 4 R MBRT (V4) [V] B MBRT (V5) [V] 5 RGB SBRT adjustment range 12 10 8 1 2 R SBRT, B SBRT adjustment range VSB [V] 6 4 2 0 –2 2 3 4 RGB SBRT (V23) [V] 5 ∆VSSR [V] 0 –1 –2 2 3 4 R SBRT (V25) [V] B SBRT (V24) [V] 5 – 35 – CXA1853AQ RGB gamma black side gain adjustment range 20 R, B gamma black side gain adjustment range 5 15 10 ∆GGBR [dB] 2 3 4 RGB GAM GAIN1 (V68) [V] 5 GGB [dB] 0 5 0 –5 2 3 4 R GAM GAIN1 (V69) [V] B GAM GAIN1 (V70) [V] 5 RGB gamma white side gain adjustment range 20 R, B gamma white side gain adjustment range 5 15 10 ∆GGWR [dB] 2 3 4 RGB GAM GAIN2 (V71) [V] 5 GGW [dB] 0 5 0 –5 2 3 4 R GAM GAIN2 (V72) [V] B GAM GAIN2 (V73) [V] 5 RGB gamma black side breakpoint adjustment range 0 0.4 R, B gamma black side breakpoint sub adjustment range 0.2 –0.5 ∆PGBR [V] 2 3 4 RGB GAM CTR1 (V77) [V] 5 PGB [V] 0 –0.2 –1 –0.4 2 3 4 R GAM CTR1 (V78) [V] B GAM CTR1 (V79) [V] 5 – 36 – CXA1853AQ RGB gamma white side breakpoint adjustment range 0.4 R gamma white side breakpoint sub adjustment range 1.5 1 0.2 ∆PGWR [V] PGW [V] 0.5 0 –0.2 0 –0.4 –0.5 2 3 4 RGB GAM CTR2 (V74) [V] 5 2 3 4 R GAM CTR2 (V75) [V] B GAM CTR2 (V76) [V] 5 WHT LIM adjustment range 7 3 BLK LIM adjustment range VCG1 – VBGL (non-inverted side) [V] 6 2 5 ∆VW [V] 1 4 0 3 –1 2 –2 1 2 3 4 WHT LIM (V41) [V] 5 2 3 4 BLK LIM (V39) [V] 5 BLK LIM adjustment range 7 9 Signal center adjustment range VBGLA – VCG1 (inverted side) [V] 6 8 5 7 4 VC [V] 6 3 5 2 1 2 3 4 BLK LIM (V39) [V] 5 4 2 3 4 SIG CENT CTR (V37) [V] 5 – 37 – CXA1853AQ VCOM control range 3 2 ∆VCOM [V] 1 0 –1 –2 2 3 4 VCOM CTR (V36) [V] 5 SID amplitude control range 12 10 VSID [Vp-p] 8 6 4 2 3 4 SID CTR (V30) [V] 5 PRG level control range 3 VPRG [Vp-p] 2 1 0 2 3 4 PRG CTR (V31) [V] 5 – 38 – CXA1853AQ Package Outline Unit: mm 80PIN QFP (PLASTIC) 16.0 ± 0.3 14.0 ± 0.2 60 61 41 40 1.4 ± 0.2 0.1 A 80 1 0.65 0.3 ± 0.05 20 0.13 M 0.15 ± 0.05 21 1.70 MAX 0.625 ± 0.2 0.1 ± 0.1 0° to 10° DETAIL A SONY CODE EIAJ CODE JEDEC CODE QFP-80P-L111 QFP080-P-1414 PACKAGE STRUCTURE PACKAGE MATERIAL LEAD TREATMENT LEAD MATERIAL PACKAGE WEIGHT EPOXY RESIN SOLDER PLATING COPPER ALLOY 0.6g – 39 – 15.0 ± 0.2
CXA1853AQ 价格&库存

很抱歉,暂时无法提供与“CXA1853AQ”相匹配的价格&库存,您可以联系我们找货

免费人工找货