CXP1042Q

CXP1042Q System Controller for Compact Disc Players For the availability of this product, please contact the sales office. Description The CXP1042Q is a 4-bit single chip microcomputer based on the SPC500 series. It incorporates programs in firmware for CD operations. It can be connected directly to the CDL-500 series of LSIs for CD players, and can directly drive LCDs, in addition to other features. It can be employed in a wide range of equipment, from deck-type CD players to radio cassettes and portable systems. 64 pin QFP (Plastic) Functions • Key inputs of up to 16 keys is possible through matrix scanning. The following functions can be selected by setting their respective keys. , , • PLAY/PAUSE/PLAY PAUSE keys • STOP key , • SKIP key; on memory input, this becomes the tune selection key , • Fast forward key; speed differs during PLAY and PAUSE • Repeat One tune or all tunes repeat • OPEN/CLOSE Loading function (when deck type device is selected) • A← B → A← B repeat function → • SHUFFLE Shuffle (random) function • PROG Program; up to 21 tune memory, can indicate remainder • REMAIN Indicates single tune or all tunes remaining, up to 31 tunes • INTRO Fixes introscan at 10 seconds • AUTO Sets auto space at 4 seconds • MUSIC calendar Can display up to 16 tunes • REMOTE Enables input using NEC format remote control devices with modifiable custom codes • 10key Direct tune selection using keypad; selects tune on memory input (remote control only) • Syncro Synchronization input and processing •×2 Double speed playback • Battery detection When portable mode selected, there is battery detection function • Simple adjustment of tracking gain/balance Recommended Combinations • RF amplifier/servo signal processor CXA1782B • Digital signal processor CXD2507A/2508A • Pickup mechanism KSL 2101 Structure Silicon gate CMOS IC Sony reserves the right to change products and specifications without prior notice. This information does not convey any license by any implication or otherwise under any patents or other right. Application circuits shown, if any, are typical examples illustrating the operation of the devices. Sony cannot assume responsibility for any problems arising out of the use of these circuits. –1– E95236-ST CXP1042Q Features • Can be connected directly to CDL-500 series LSIs for CD use • Up to 16 keys can be connected directly; expansion of functions through addition of keys is possible Types of Keys ∗ ∗ ∗ ∗ PLAY PAUSE ∗∗ PLAY/PAUSE ∗∗ REP STOP F.SKIP B.SKIP F.F F.R ∗∗ OPEN CLOSE SHL REM A B AUTO INTR PRG When deck mode is selected SHUFFLE REPEAT REMAIN A B REPEAT AUTO SPACE INTRO PROGRAM CHECK ∗/∗∗ Multiple functions can be combined. • LCDs can be driven directly. This includes time display, music calendar, remaining tunes and other display functions. • NEC format remote control input possible; direct tune selection through keypad and other functions can be added. • Supports auxiliary functions including synchronization input and double-speed playback. • Easy switching between deck and portable equipment using external pins. (i) With deck type selected, performs tray loading function. (ii) With portable type selected, displays detection of weak battery and executes emergency termination when battery voltage is low. In this way, it functions specific to the system required. • An simple tracking gain/balance function is built-in, enabling adjustment of the tracking gain/balance according to the disc. –2– Reference Circuit F+ T+ T– F– VR PD GND LD 87654321 F E K G A B C D 12345678 (+VCC) 0.01µ 100k (TEX) (+5) REPEAT 1 ALL A B SHUFFLE X2 PROGRAM 1a 2 BATT 3 4 5 6 MEMORY fgb INTRO c REMAIN e SPACE (SPX) (SPY) (SP) (TEY) (VC) 0.01µ 150k d 1 5 9 13 2 6 10 14 3 7 11 15 4 8 12 16 (+5) (+5A) (LDD) (VC) (TE) (FEY) 48 47 46 45 44 43 42 41 40 39 38 37 VC IDFCT TZC ATSC TE1 LPF1 TE0 VEE E1 E F FB 14 13 12 11 10 8 7 3 1 36 35 34 33 32 31 30 29 28 27 26 25 5 4 2 1 6 9 GND LO– MREF SP+ SPIN CNTL GND MUTE REG1 REG2 (–) FIN F+ F– SP+ 1 SP– 2 SL+ 3 SL– 4 LS 5 GND 6 (FE) 2 3 4 5 6 (LD) 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 TEST NORMAL Drive IC LOR LOF SL– SL+ LDIN SLIN VCC VCC VREF (–) TIN T– T+ GND CXA1782Q FEQ FEI FOFCT FGQ PQ2 PQ1 PQ LQ 52 32 53 15 16 17 18 19 20 21 8 9 10 11 22 23 24 25 26 27 28 7 31 54 30 (RF) (LDY) (LDX) 55 29 56 28 57 27 58 CXP1042Q (SLX) (SLY) TA0 SL+ SL– 12 26 1 2 59 VLC1 VLC2 VLC3 VDD VL LD+ LD– LSD GND LS1 3 4 5 (SL) VDD VSS 25 FLB FAQ FA– SRCH TGU TG2 FSET TA– SL0 ISET VCC CLK XLT DATA XRST COUT SENS RF– RFD RFI CP CB CC1 CC2 FOK (VC) (FDK) 2MHz 60 24 61 23 13 14 15 16 17 18 19 20 21 22 23 24 XRST 62 RST 22 63 21 64 INT1 20 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 REM A-B AUTO INTR PRG REP SHL OPEN REMOCON MODULE (GND) XLT FOK SCOR SQCK/CLK DATA SENSE SUBQ GF5 KEY SCAN MUTG REMOCON CUSTOM CODE PORTABLE DECK "0" DIODES "1" Low-pass filter + audio circuit 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 (CHIP) (FEX) Bat-E MUT2 R515 22k MON FDK XLON XTSL SPOC SPOB SPOA CLK0 XLT0 DAT0 CNIN SEIN VSS CLOK XLAT DATA XRST SENS MUTE SOCK SOSO EXCK SBSO SCOR 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 (C2) CXP1042Q (M3) (M1) (M0) NDCK LRCK LRCK1 PCMD PCMD1 GCN GCN1 GTOP XUGF XFCN GFS RFCK VSS C2P0 XROF MNT3 MNT1 MNT0 FSTT CAM DOUT EMPH EMPH1 WFCK –3– (L) 1L (AG) 2 AGND (R) 3R 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 80 79 78 77 76 75 74 73 (RP) (NRP) (CHIP) CXD2508AQ 72 71 70 69 68 67 66 65 MOP MOS LOCK TEST FIL0 FIL1 PCQ VDD AVSS1 CLTV AVDD1 RF BIAS ASV1 ASV0 ASVE DTS3 DTS2 RPWM NRPWM AVSS2 AVSS XTA0 XTA1 AVDD AVDD LPWM NLPWM VDD DTS1 ZERDA ZERDL (LP) (NLP) 57 58 59 60 61 62 63 64 CXP1042Q Pin Configuration and Pin Description PB2/UNLOAD/Batt-W PD3/Disc OUT/Batt-E PD2/Disc IN/OPEN PX2/SENSE SC/SQCK/CLK PD1/SYNC IN PB0/MUTG PB1/MUT2 POB/DATA EC/SCOR PD0/GFS PY2/FOK SI/SUBQ PY1/MODE 2 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 PY0/XLT 1 64 63 62 61 60 59 58 57 56 55 54 53 52 PC3/KI3 PC2/KI2 PC1/KI1 PC0/KI0 LOAD/DECK-PT/PB3 KS0/PA0 KS1/PA1 KS2/PA2 KS3/PA3 VSS N.C. RS3/PE3 RS2/PE2 RS1/PE1 RS0/PE0 SEG19 SEG18 20 21 22 23 24 25 26 27 28 29 30 31 32 INT1 WP RST EXTAL XTAL VL VDD VLC3 VLC2 VLC1 COM0 COM1 COM2 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 SEG14 SEG15 SEG9 SEG16 SEG10 SEG4 SEG3 SEG17 SEG11 SEG12 SEG13 Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Symbol Function code PY0 PY1 PY2 PY3 PX0 PX1 PX2 PX3 PD0 PD1 PD2 PD3 PC0 PC1 PC2 PC3 XLT MODE FOK SCOR SQCK/CLK DATA SENSE SUBQ GFS SYNC IN Disc IN∗1/ OPEN Disc Out∗1/ Batt-E KI0 KI1 KI2 KI3 I/O O O I I O O I I I I I I I I I I –4– Description Latch output; connect to XLAT of CXD2507A/2508A Setting scan output signal for microcomputer operation mode Inputs focus condition; connect to CXA1782B FOK SCOR input; connect to CXD2507A/2508A SCOR SUB-Q reading clock output; 8-bit data clock output 8-bit data output Sense input (monitor for different systems); connect to CXD2507A/2508A SENS SUB-Q code input port; connect to CXD2507A/2508A SQSO Monitors disc state; connect to CXD2507A/2508A GFS Used to start the CD synchronously with external equipment (cassette deck, etc). Starts at falling edge ( ) Switch to "L" when tray enters unit in deck mode, or when lid is closed in portable mode Switch to "L" when tray is open in deck mode, and when there are no batteries in portable mode Key scan input port; reads the remote control custom code on reset or startup and setting state of the microcomputer operation mode COM3 SEG5 SEG6 SEG7 SEG8 SEG2 SEG1 SEG0 CXP1042Q Pin No. 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 Symbol Function code PB0 PB1 PB2 PB3 PA0 PA1 PA2 PA3 Vss N.C. PE3 PE2 PE1 PE0 SEG19 SEG18 SEG17 SEG16 SEG15 SEG14 SEG13 SEG12 SEG11 SEG10 SEG9 SEG8 SEG7 SEG6 SEG5 SEG4 SEG3 SEG2 SEG1 SEG0 MUTG MUT2 UNLOAD/ Batt-W LOAD/ DECK-PT KS0 KS1 KS2 KS3 Vss NC RS3 RS2 RS1 RS0 — SEG18 SEG17 SEG16 SEG15 SEG14 SEG13 SEG12 SEG11 SEG10 SEG9 SEG8 SEG7 SEG6 SEG5 SEG4 SEG3 SEG2 SEG1 SEG0 I/O O O I/O I/O O O O O Connect to GND Do not connect to anything O O O O Key scan output signal Description Turns mute on when mute signal is "H"; turned on when unit is opened or stopped Turns mute on when "L", turned on when unit is opened, stopped, paused or accessed. In deck mode, output to tray loading motor; in portable mode, output to battery warning display In deck mode, indicates tray loading motor operation; on "L" detection immediately after reset, performs portable mode branching RMC customer code scan signal Unused (do not connect to anything) O O O O O O O O O O O O O O O O O O O Connect to LCD (refer to LCD example) –5– CXP1042Q Pin No. 51 52 53 54 55 56 57 58 59 60 61 62 63 64 Symbol Function code COM3 COM2 COM1 COM0 VLC1 VLC2 VLC3 VDD VL XTAL EXTAL RST WP INT1 RMC XTAL EXTAL Reset VDD COM3 COM2 COM1 COM0 I/O O O O O Description Connect to LCD (refer to LCD example) LCD bias power supply VDD O LCD bias power supply Connect to a 2MHz oscillator I I/O I I Connect to a 2MHz oscillator Connect reset Not used (connect to Vss or VDD) Connect to remote control input and remote control module (Mentioned here after with Pin No./Function code.) The expansion port of the CXD2507A/2508A is used to detect the LD on/off output, limit switch input and tray open/close input. CXD2507A/2508A Pin No. 2507A 61 2508A 19 SPOB LIMSW I Limit switch input. "L" when the pickup is at the innermost track. LD on/off "L": on, "H": off At this point, switch the IC whose one driver output functions also as spindle loading motor output. Goes "L" when the tray is fully opened. Goes "L" when the tray is closed. Symbol Function code I/O Description 64 22 XLON LDON DISC OUT∗2 (OPEN) DISC IN∗2 (CLOSE) O 63 18 62 20 SPOD SPOA SPOC I I ∗1, ∗2 The tray switch is determined according to the state where Pin 2 (PY1/MODE) and Pin 16 (PC3/KI3) is connected immediately after reset or not. Connected: DSP expansion port used Not connected: Microcomputer port used However, use the microcomputer port when the OPEN/Batt-E function is employed for portable mode. The selected mute (Pin 2 (PY1/MODE) or Pin 15 (PC2/KI2)) is used to identify which of the CXD2507A or CXD2508A is employed for DSP. Therefore, select the suitable method for the used DSP. CXD2508A: DAC mute selected CXD2507A: DSP mute selected –6– CXP1042Q LCD Example REPEAT 1 ALL A B SHUFFLE X2 PROGRAM 1a 2 BATT 3 4 5 6 MEMORY fgb INTRO e c REMAIN SPACE d 1 5 9 13 2 6 10 14 3 7 11 15 4 8 12 16 No. REPEAT 1 ALL A B SHUFFLE X2 PROGRAM 1a 2 BATT 3 4 5 6 MEMORY fgb INTRO c REMAIN e SPACE d COM. 3 COM. 2 COM. 1 COM. 0 COM. 0 1 5 9 13 2 6 10 14 3 7 11 15 4 8 12 16 Function code COM0 COM1 COM2 COM3 1 2 3 4 5 COM. 3 REMAIN 1d 1c 2d 2c 1e 1g 2e 2g — 3d 3c 4d 4c 5d 5c 6d 6c SPACE 13 14 15 16 3e 3g 4e 4g 5e 5g 6e 6g INTRO 9 10 11 12 1f 1b 2f 2b B 3f 3b 4f 4b 5f 5b 6f 6b COM. 2 COM. 1 REPEAT 1 (Left) 1a ALL 2a A← → BATT 3a SHUFFLE 4a : 5a ×2 6a SEG0 SEG1 SEG2 SEG3 SEG4 SEG5 SEG6 SEG7 SEG8 SEG9 SEG10 SEG11 SEG12 SEG13 NO23 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 NO1 MEMORY PROGRAM SEG14 5 6 7 8 1 (Right) SEG15 2 3 4 SEG16 SEG17 SEG18 –7– CXP1042Q Key Matrix The CXP1042Q has the key matrix configuration shown below. KS3/PA3 KS2/PA2 KS1/PS1 KS0/PS0 24 23 22 21 KI1/PC1 13 KI0/PC0 14 15 KI2/PC2 16 KI3/PC3 ∗ REM A B ∗ REP∗ AUTO SHL INTR OPEN CLOSE PRG ∗ Key combination mode , key and REP key have the combination mode which combines the other keys' functions. 1. , key combination mode Combination mode is set when Pin 2 (MODE) and Pin 13 (KI0) is not connected with diode. In this time, combines the function. 2. REP key combination mode Combination mode is set when Pin 2 (MODE) and Pin 14 (KI1) is not connected with diode. In this time, REP combines SHL and PRG functions. –8– CXP1042Q List of Functions 1. Deck/Portable select Switches between deck mode and portable mode. In deck mode the tray loading function is activated; in portable mode, the battery detection function is activated. Accepts signals from a NEC format remote control unit. A 16-bit custom code can be selected. Keys to initiate playing can be selected. Performs tune selection. Performs fast-forward and rewind. The speed differs during Play and Pause. Can display Single Remain, All Remain, Program Remain. For repetition of one or of all tunes. For performance of A← B repeat. → Performed shuffled (random) playing. Inserts 4-second blanks between tunes. Plays the initial 10 seconds of a disc. Enables programming of up to 21 tunes. Enables direct tune selection using the keypad (for use with a remote control unit only). A function for detection of reduced battery voltage is provided by the BattW and Batt-E pins (portable mode only). For sync rate input and activation. , Double-speed playback is executed only when key is set to the independent mode and REP key to repeat key if sync rate input is made for stop. With the deck mode selected, tray loading is possible. The tune select and fast-forward keys can be combined or kept independent, and the repeat key and mode key can be selected. 2. Remote control input 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. , , , , , Remain Repeat A← B → Shuffle AUTO INTRO PROG 1 to 10 , +10 14. Battery input 15. Sync rate input 16. Double-speed playback 17. Loading function 18. Key combining function –9– CXP1042Q 1. Deck mode/portable mode selection A feature of the CXP1042Q is its ability to be used in both deck-type and in portable equipment. (a) Selection Selection is executed through Pin 20 (LOAD/DECK-PT). Mode selection is determined by the condition of this pin immediately after reset of the CXP1042Q. When Pin 20 (LOAD/DECK-PT) is high: Deck mode When Pin 20 (LOAD/DECK-PT) is low: Portable/radio cassette mode (b) Deck mode • In deck mode the tray loading function is activated. • Pins necessary for tray operation: For the loading motor Pin 19 (UNLOAD/Batt-W) goes "H" when tray is ejected Pin 20 (LOAD/DECK PT) goes "H" when tray is closed For the tray SW Disc IN goes "L" when the tray is closed Disc OUT goes "L" when tray is fully opened Tray UNLOAD direction LOAD direction The tray switch state is input from the microcomputer port or DSP port according to the microcomputer operation mode. • The relation between Pin 19 (UNLOAD/Batt-W) and Pin 20 (LOAD/DECK-PT) is as follows. State Open (stopped) LOAD direction UNLOAD direction Close completed (stopped) Pin 19/UNLOAD H L H H Pin 20/LOAD H H L H (c) Portable mode • In portable mode, when the lid is closed the operation changes to TOC reading. • Pin 20 (LOAD/DECK-PT) should be held "L". • Pin 11 (Disc IN/OPEN) should be connected to a switch that makes the pin go "L" when the lid is closed. • Two pins used in deck mode can be employed to detect a reduced battery voltage. • When Pin 19 (UNLOAD/Batt-W) is made "L" through the reduced voltage detection circuit, BATT is displayed. • In addition, when Pin 19 (UNLOAD/Batt-W) is "L", forcing Pin 12 (Disc OUT/Batt-E) "L" induces the STOP state. • Input the Disc IN/OPEN and Disc OUT/Batt-E to the microcomputer port because the DSP expansion port can not be used for the portable mode. (d) Selection of tray switch input port The microcomputer port or DSP port can be selected for the tray switch input (Disc IN/OUT) according to the state where Pin 2 (MODE) and Pin 16 (KI3) is connected immediately after reset or not. Not connected: Microcomputer port used Connected with diode: DSP port used However, use the microcomputer port when the OPEN/Batt-E function is employed for portable mode. – 10 – CXP1042Q Selection State of Operation Mode and Connection of Each Switch Deck mode DSP expansion port used DSP: CXD2507A DSP: CXD2508A Setting of mode selection pin Operation mode Deck mode Microcomputer port used H L Portable mode Pin 20 (LOAD/DEC-PT) Pin 2 (MODE) and Pin 16 (KI3) Pin 2 (MODE) and Pin 15 (KI2) Lid open switch H H Connected Connected Not connected — Connected Not connected — — Microcomputer Pin 11 (Disc IN/OPEN) Microcomputer Pin 19 (UNLOAD/Batt-W) Microcomputer Pin 12 (Disc OUT/Batt-E) — — — — Battery switch Connected switch — — — Detection switch without battery — — — Microcomputer Pin 11 (Disc IN/OPEN) Microcomputer Pin 12 Disc OUT/Batt-E) SPOB for DSP Tray open switch SPOD for DSP SPOA for DSP Tray close switch Limit switch SPOC for DSP SPOB for DSP SPOC for DSP SPOB for DSP — SPOB for DSP – 11 – CXP1042Q 2. Selection of microcomputer operation mode In the CXP1042Q, functions can be selected according to the state where Pin 2 (MODE) and Pins 13 to 16 (KI0 to 3) are connected with diode immediately after reset or not. Tray switch Not connected: Microcomputer port Connected: DSP port Pin 16 (KI3) Mute Not connected: DAC mute Connected: DSP mute Pin 15 (KI2) REP key function Not connected: Combine mode Connected: Repeat key Pin 14 (KI1) , key function Not connected: Combine mode Connected: Independent mode Pin 13 (KI0) Selection function Applicable pin Example of connection 16 15 14 13 2 In this example, the microcomputer port and DSP mute (CXD2507A) is used for the tray switch, and the REP key is used as repeat key and / key is used in the combination mode. • Tray switch selection Connected: Input the content of tray switch from the DSP expansion port Not connected: Input the content of tray switch from the microcomputer port • Mute selection Connected: DSP mute (select for the CXD2507A used) Not connected: DAC mute (select for the CXD2508A used) • , key function selection Connected: / , / key independent mode Not connected: / , / key combination mode Operation for combination mode Function differs depending on length of time pressed and state of operation • In stopped state: Functions as , key regardless of the length of time pressed If the length of time pressed for playback is: • 0.5 seconds or less: Functions as , key • Longer than 0.5 seconds: Functions as , key • REP key function selection Connected: Functions as repeat key Not connected: Functions as combination mode Operation of combination mode Function differs depending on the state of operation • In stopped state: Functions as program key • In normal playback state: Switches between single-tune repeat, all-tune repeat and tune shuffle • In program playback state: Switches between single-tune repeat and all the programmed tunes repeat Select the the independent mode for , key and repeat key for REP key to execute the double-speed playback. – 12 – CXP1042Q 3. Mute function The CXP1042Q has two mute pins, Pin 17 (MUTG...active high) and Pin 18 (MUT2...active low). The command transferred to the DSP and the state of mute pin differ depending on the selected mute method when mute is turned on. • DAC mute (CXD2508A used) When "mute on" is requested, set Pin 18 (MUT2) active and then transfer the attenuate command (A00000h) to the DAC. Only when "open/stop" is requested, set Pin 17 (MUTG) active after approximately 32ms from the command transfer. • DSP mute (CXD2507A used) When "mute on" is requested, set Pin 17 (MUTG) and Pin 18 (MUT2) active and then transfer the mute command (A207F0h) to the DSP. Note that A007F0h is transferred when mute is turned off both for DAC mute and DSP mute. Timing chart for mute on Operation request STOP ACCESS PLAY PAUSE PLAY STOP DAC mute Command to DSP A00000 A007F0 A00000 A007F0 A00000 32ms MUT2 pin MUTG pin DSP mute Command to DSP A207F0 A007F0 A207F0 A007F0 A207F0 MUT2 pin MUTG pin – 13 – CXP1042Q 4. Remote control Any NEC format remote control can be used. Please note that no other remote control units are supported. (a) Format 67.5ms 108ms 108ms 9ms 4.5ms Custom Code 16bit Data Code 8bit Data Code 8bit 13.5ms Leader Code (b) 27ms 67.5ms (c) 27ms (b) Custom code setting 16 bits of the custom code can be set. (c) Remote control data Code D7 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 D0 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 Contents Code D7 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 D0 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 Contents OPEN 7 10 27 28 29 30 (0001) (0010) (0011) (0100) 16 15 14 13 0 SHUFFLE Repeat 1 Remain 0 1 PROGRAM 0 INTRO 1 AUTO SPACE 0 A← B → 1 — 0 — 1 1 0 1 0 — 1 4 0 1 8 +10 9 — 5 6 — 2 3 (Example: custom code "1234") By forming a diode matrix, a single bit of data is created; adding a diode at each point sets that point to "0". Please use the above example as a reference. This matrix is read only immediately after the power is turned on. The data on the receiving end is as shown above and cannot be changed. For the transmitting end, please refer to the specifications of the transmitting side chip. – 14 – CXP1042Q 5. To play in deck mode (a) Turn the power on. • If the tray is in the open state, a disc can be loaded. • A focus search is performed, and if a disc is already loaded, the TOC is read. • If a disc is not loaded, "disc" is displayed. (b) When the TOC has been read 1234 5678 (c) To load a disc • Press OPEN (d) To play the disc • Press 1234 5678 or . (e) To pause during playing • Press 1234 5678 or . (f) To stop playing • Press 1234 5678 – 15 – CXP1042Q 6. To play in portable mode (a) Turn the power on. • When the lid is open, no operation takes place. • A focus search is performed, and if a disc is already loaded, the TOC is read. • When no disc is loaded, "disc" is displayed. (b) When the TOC has been read 1234 5678 (c) To load a disc • Open the lid. (d) To play the disc • Press or . 1234 5678 (e) To pause during playing • Press or . 1234 5678 (f) To stop playing • Press 1234 5678 . – 16 – CXP1042Q Functions common to the deck mode and the portable/radio cassette mode. 7. To begin listening from a specific tune • Press or . (Example: Sixth tune specified) • If the keys are pressed continuously, the tune number continues to change. • After a few seconds playing starts. 678 678 →tune can be specified directly only by remote control. Tunes 1 to 10 can be specified directly using the corresponding keys. For tunes following tune 10, the following procedure is used. • Press +10 . • Following this, press a key from 1 to 10 . • If there are not more than 10 tunes on the disc, the +10 key is invalid. 8. To move to a desired place on the disc • During play, press or . • The player moves at high speed, emitting a small sound during play, or without emitting a sound during pause. 9. To check the time remaining on the disc • Press Remain . • When pressed once, the time remaining for the tune currently being played is displayed. When the tune being played is beyond the 32nd tune, " " is displayed. • Pressing Remain once again causes the time remaining on the disc to be displayed. 1 5 9 13 2 6 10 14 3 7 11 15 4 8 12 16 1 5 9 13 2 6 10 14 3 7 11 15 4 8 12 16 REMAIN REMAIN • Pressing Remain once again restores the normal display. REMAIN 1 5 9 13 2 6 10 14 3 7 11 15 4 8 12 16 – 17 – CXP1042Q 10. To repeat a tune or tunes • Press Repeat . • Pressing once causes one tune to be repeated. • Pressing once more causes all tunes to be repeated. In program playback mode, all the programmed tunes to be repeated. • Pressing once more turns off Repeat mode. REPEAT 1 1234 5678 REPEAT ALL 1234 5678 234 5678 11. A← B repeat function → Used to repeatedly play the part of the disc from a certain point A to a certain point B. • At the starting point of the interval A← B, press A← B . → → • At the ending point of the interval A← B, once again → press A← B . On doing so, the interval A← B will be → → played repeatedly. • To stop repeated A← B play, press A← B once → → again, or press Repeat . 12. To play tunes out of order (Shuffle) SHUFFLE REPEAT AB 1234 5678 REPEAT AB 1234 5678 • Press SHUFFLE . • Press or . 1 5 9 13 2 6 10 14 34 78 11 12 15 • Play starts. • If SHUFFLE is pressed during play, shuffled play starts from the end of the current tune. SHUFFLE 1 5 9 13 2 6 10 14 34 78 11 12 15 SHUFFLE 78 9 10 11 12 13 14 15 16 – 18 – CXP1042Q 13. To insert a 4-second blank between tunes When dubbing onto tapes or in similar situations, it is sometimes necessary to insert blanks between tunes. • Press AUTO . • Pressing AUTO once more cancels the function. Note) When playing the introduction and when is pressed, blank is not inserted. 14. To listen to the disc introduction only for 10 seconds • Press INTRO . • Pressing INTRO once more cancels the function. • It is possible to play the introduction during Shuffle and Program operation also. REPEAT ALL SHUFFLE INTRO 234 5678 9 10 11 12 SPACE 13 14 15 16 1 5 INTRO 9 13 2 6 10 14 3 7 11 15 4 8 12 16 • In Repeat All mode, introduction play does not halt even when the last tune is reached, but is repeated. PROGRAM 6 8 INTRO 9 10 12 13 15 – 19 – CXP1042Q 15. Program play Up to 21 tunes can be programmed for listening and played. (a) Press PROG . MEMORY (b) Select a tune number using the and keys. (The remote control 1 to 10 and +10 keys can also be used.) MEMORY (c) Press PROG . Repeat steps (b) and (c) for all the tunes desired. MEMORY 1 (d) Indicate that input is completed by pressing . (e) When Remain is pressed while in state (b), the total remaining time is displayed while the key is pressed. By using the and keys with the Remain key, the total play time can be checked while programming. (f) If, among the tunes included in programming, any one or more tunes is numbered above 32, the display shown on the right appears. 1 MEMORY 1 MEMORY 5 3 7 11 – 20 – CXP1042Q (g) Pressing or begins play. PROGRAM 1 5 3 7 11 (h) The music calendar of a tune disappears as the tune is completed. PROGRAM 5 7 11 (i) In the above state, pressing the Remain key causes the remaining time of the tune being played to display. REMAIN PROGRAM 1 5 3 7 11 (j) If the tune being played is numbered above 32, the display shown on the right appears. REMAIN PROGRAM 5 3 7 11 (k) During display of the remaining time of the current tune, if the Remain key is pressed once more the remaining time for all the programmed tunes is displayed. PROGRAM 5 REMAIN 3 7 11 (l) If any of the tunes remaining to be played is numbered above 32, the display shown on the right appears. REMAIN PROGRAM 1 5 3 7 11 (m) To stop playing press . To play the previous program again, press PROG once more and set Memory mode. The contents of the previous program are stored and can be used again. When the tray or lid is opened, the program contents are cleared. – 21 – CXP1042Q 16. Battery input (in portable mode) Using pins: Pin 19 (UNLOAD/Batt-W) Pin 12 (Disc OUT/Batt-E) 4 5678 9 10 11 12 13 14 15 16 BATT (a) When Batt-W is "L", the BATT lamp lights. BATT (b) When both Batt-W and Batt-E are "L", the unit is forced to stop, "disc" is displayed, and keys no longer function. 17. Sync rate function X2 This function is used to play the CD player in synchronization with the record key of a cassette deck. Operation is triggered by (the falling edge), and differs depending on the state of the CD player. (a) While stopped The CD player enters the Play state, and starts after 4 seconds. During this time, double-speed playback is executed when , key is set to the independent mode and REP key to repeat key. (b) During play pause The CD player pauses at the beginning of the current tune, and after 4 seconds begins playing. SHUFFLE X2 1 5 9 13 2 6 10 14 3 7 11 15 4 8 12 16 678 9 10 11 12 13 14 15 16 1 5 9 13 2 6 10 14 3 7 11 15 4 8 12 16 (c) While open When the tray is loaded, the player enters the Play state. Output is not at double speed even for any operation mode. (d) During shuffled play Play is shuffled, and (a) and (b) are executed. (e) During program play Program play begins, and (a) and (b) are executed. 8 9 10 11 12 13 14 15 16 X2 PROGRAM 1 5 9 3 7 11 – 22 – CXP1042Q Absolute Maximum Ratings Item Supply voltage LCD bias voltage Input voltage Output voltage High level output current High level total output current Low level output current Low level total output current Operating temperature Storage temperature Allowable power dissipation VDD VLC1, VLC2, VLC3 VIN VOUT IOH ∑IOH IOL ∑IOL Topr Tstg PD Symbol Rating –0.3 to +7.0 –0.3 to +7.0∗1 –0.3 to +7.0∗1 –0.3 to +7.0∗1 –5 –50 15 50 –20 to +75 –55 to +150 600 Unit V V V V mA mA mA mA °C °C mW (Ta = –20 to +75°C, Vss = 0V) Remarks General purpose port 1 pins∗2 Total for all output pins General purpose port 1 pins∗2 Total for all output pins QIP ∗1 VLC1, VLC2, VLC3, VIN and VOUT must not exceed VDD + 0.3V. ∗2 PA to PD, PX0 to PX2, PY0, PY1 and, when the mask option port is selected, PE and PF. Note) Usage exceeding absolute maximum ratings may permanently impair the LSI. Normal operation should be conducted under the recommended operating conditions. Exceeding these conditions may adversely affect the reliability of the LSI. Recommended Operating Conditions Item Supply voltage LCD bias voltage VDD VLC1, VLC2, VLC3 VIH High level input voltage VIHS VIHEX VIL Low level input voltage VILS VILEX Operating temperature Topr Symbol Min. 3.5 Vss 0.7VDD 0.8VDD VDD – 0.4 0 0 –0.3 –20 Max. 5.5 VDD VDD VDD VDD + 0.3 0.3VDD 0.2VDD 0.4 +75 Unit V V V V V V V V °C Hysteresis input∗4 EXTAL pin∗5 Hysteresis input∗4 EXTAL pin∗5 LCD power supply range∗3 (Vss = 0V) Remarks ∗3 The optimum value will vary depending on the characteristics of the liquid crystal display. ∗4 Each pin of INT1, WP, PX0, PX3, PY2, PY3, and RST. ∗5 Specified only for external clock input. – 23 – CXP1042Q Electrical Characteristics DC characteristics Item High level output voltage Low level output voltage Symbol VOH Pin PA to PE∗1 PX0 to PX2 PY0, PY1 VL (VOL only) RST (VOL only) EXTAL∗2 RST∗3 PA to PF, PX0 to PX2, PY0, PY1 PX3, PY2, PY3, INT1, WP COM0 to COM3 SEG0 to SEG19 VDD = 5.5V, VIL = 0.4V –2.0 mA Conditions VDD = 4.5V, IOH = –10µA VDD = 4.5V, IOH = –200µA VDD = 4.5V, IOL = 1.8mA VDD = 4.5V, IOL = 3.6mA VDD = 5.5V, VIH = 5.5V 0.5 –0.5 –1.5 (Ta = –20 to +75°C, Vss = 0V) Min. 4.0 2.4 0.4 0.6 40 –40 –400 Typ. Max. Unit V V V V µA µA µA VOL IIH IILE Input current IILR IIL High impedance input/output leakage current Common output impedance Segment output impedance IIZ VDD = 5.5V VDD = 5V VLC1 = 3.75V VLC2 = 2.5V VLC3 = 1.25V VDD = 5.5V external clock, 1MHz; all output pins open ±10 µA kΩ kΩ RCOM RSEG IDD 3 5 5 15 Supply current IDDSP IDDS VDD 2 6 mA Input pin capacitance CIN All pins other than VLC1 to VLC3, Clock 1MHz, COM0 to COM3, 0V for pins other than SEG0 to SEG15, those measured. SEG16 to SEG19, VDD, Vss 10 20 pF ∗1 Pull-up resistances selected for each of pins PA to PF, PY0 and PY1. ∗2 Crystal or ceramic oscillator circuit selected. ∗3 Pull-up resistance selected for the RST pin. – 24 – CXP1042Q AC Characteristics (1) Clock timing Item System clock frequency System clock input pulse width System clock input rise, fall times Event count clock input pulse width Event count clock input rise, fall times ∗ tsys = 8/fc Note) When accurately adjusting the frequency, conditions may differ from those of Fig. 2. Symbol fc Pin XTAL EXTAL (Ta = –20 to +75°C, VDD = 3.5 to 5.5V, Vss = 0V) Conditions Figs. 1, 2 Min. 2 90 EXTAL Figs. 1, 2 200 PY3/EC PY3/EC Fig.3 Fig.3 ns µs 20 ms Max. 2 Unit MHz ns tXL tXH tCR tCF tEL tEH tER tEF tsys∗ + 0.05 1/fC VDD – 0.4V EXTAL 0.4VDD tXH tCF tXL tCR Fig. 1. Clock timing Crystal oscillation Ceramic oscillation External clock EXTAL XTAL EXTAL XTAL OPEN C1 C2 Fig. 2. Clock applied conditions 0.8VDD PY3/EC 0.2VDD tEH tEF tEL tER Fig. 3. Event count clock timing – 25 – CXP1042Q (2) Serial transfer Item Serial transfer clock (SC) cycle time Serial transfer clock (SC) high-low level width Serial data input set-up time (relative to SC) Serial data input hold time (relative to SC) Time delay from SC falling edge for high data output Delay time from SC falling edge for low data output Note) tsys=8/fc Symbol Pin SC (Ta = –20 to +75°C, VDD = 3.5 to 5.5V, Vss = 0V) Conditions Input mode Output mode Input mode Output mode SC input mode SC output mode SC input mode SC output mode Min. Max. Unit µs µs µs µs µs µs µs µs µs tKCY tKH tKL tSIK tKSI tKSOB SC tsys/4 + 1.42 tsys tsys/8 + 0.7 tsys/2 – 1.6 0.1 0.2 SI SI SOB SOB tsys/8 + 0.5 0.1 tsys/8 + 0.5 µs tKCY tKL tKH 0.8VDD SC 0.2VDD tSIK tKSI 0.8VDD SI Input data 0.2VDD tKSOA tKSOB 0.8VDD SOB 0.2VDD Output data Fig. 4. Serial transfer timing – 26 – CXP1042Q (3) Others Item External interruption high, low level width Reset input low level width Note) tsys = 8/fc Symbol Pin INT1 RST (Ta = –20 to +75°C, VDD = 3.5 to 5.5V, Vss = 0V) Conditions Edge detection mode Min. Max. Unit µs µs tI1H, tI1L tRSL tsys + 0.05 2tsys tI1L tI1H INT1 (rising edge) 0.2VDD 0.8VDD tI1H tI1L INT1 (falling edge) 0.8VDD 0.2VDD Fig. 5. Interruption input timing tRSL RST 0.2VDD Fig. 6. RST input timing – 27 – CXP1042Q Package Outline Unit: mm 64PIN QFP(PLASTIC) 23.9 ± 0.4 + 0.4 20.0 – 0.1 51 33 + 0.1 0.15 – 0.05 0.15 52 32 17.9 ± 0.4 + 0.4 14.0 – 0.1 64 20 + 0.2 0.1 – 0.05 1 1.0 + 0.15 0.4 – 0.1 19 + 0.35 2.75 – 0.15 ± 0.12 M PACKAGE STRUCTURE PACKAGE MATERIAL SONY CODE EIAJ CODE JEDEC CODE QFP–64P–L01 ∗ QFP064–P–1420 LEAD TREATMENT LEAD MATERIAL PACKAGE WEIGHT EPOXY RESIN SOLDER/PALLADIUM PLATING COPPER /42 ALLOY 1.5g – 28 – 0.8 ± 0.2 16.3